Network Working Group S. Hartman
Internet-Draft Painless Security
Intended status: Informational D. Zhang
Expires: January 06, 2014 Huawei
July 05, 2013

Operations Model for Router Keying
draft-ietf-karp-ops-model-07.txt

Abstract

Developing an operational and management model for routing protocol security that works with all the routing protocols will be critical to the success of routing protocol security efforts. This document discusses issues and begins to consider development of these models.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at http://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on January 06, 2014.

Copyright Notice

Copyright (c) 2013 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License.


Table of Contents

1. Introduction

The KARP working group is designing improvements to the cryptographic authentication of IETF routing protocols. These improvements include improvements to how integrity functions are handled within each protocol as well as designing an automated key management solution.

This document discusses issues to consider when thinking about the operational and management model for KARP. Each implementation will take its own approach to management; this is one area for vendor differentiation. However, it is desirable to have a common baseline for the management objects allowing administrators, security architects and protocol designers to understand what management capabilities they can depend on in heterogeneous environments. Similarly, designing and deploying the protocol will be easier with thought paid to a common operational model. This will also help with the design of NetConf schemas or MIBs later.

This document also gives recommendations for how management and operational issues can be approached as protocols are revised and as support is added for the key table [I-D.ietf-karp-crypto-key-table]

2. Requirements notation

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119].

3. Breakdown of KARP configuration

There are multiple ways of structuring configuration information. One factor to consider is the scope of the configuration information. Several protocols are peer-to-peer routing protocols where a different key could potentially be used for each neighbor. Other protocols require the same group key to be used for all nodes in an administrative domain or routing area. In other cases, the same group key needs to be used for all routers on an interface, but different group keys can be used for each interface.

Within situations where a per-interface, per-area or per-peer key can be used for manually configured long-term keys, that flexibility may not be desirable from an operational standpoint. For example consider OSPF [RFC2328]. Each OSPF link needs to use the same authentication configuration, including the set of keys used for reception and the set of keys used for transmission, but may use different keys for different links. The most general management model would be to configure keys per link. However for deployments where the area uses the same key it would be strongly desirable to configure the key as a property of the area. If the keys are configured per-link, they can get out of sync. In order to support generality of configuration and common operational situations, it would be desirable to have some sort of inheritance where default configurations are made per-area unless overridden per-interface.

As described in [I-D.ietf-karp-crypto-key-table], the cryptographic keys are separated from the interface configuration into their own configuration store. Each routing protocol is responsible for defining the form of the Peer specification used by that protocol. Thus each routing protocol needs to define the scope of keys. For group keying, the Peer specification names the group. A protocol could define a Peer specification indicating the key had a link scope and also a Peer specification for scoping a key to a specific area. For link-scoped keys it is generally best to define a single Peer specification indicating the key has a link scope and to use interface restrictions to restrict the key to the appropriate link.

Operational Requirements: implementations of this model MUST support configuration of keys at the most general scope for the underlying protocol; protocols supporting per-peer keys MUST permit configuration of per-peer keys, protocols supporting per-interface keys MUST support configuration of per-interface keys, and so on. Implementations MUST NOT permit configuration of an inappropriate key scope. For example, configuration of separate keys per interface MUST NOT be supported for a protocol requiring per-area keys. This restriction can be enforced by rules specified by each routing protocol for validating key table entries. As such these implementation requirements are best addressed by care being taken in how routing protocols specify the use of the key tables.

3.1. Integrity of the Key Table

The routing key table [I-D.ietf-karp-crypto-key-table] provides a very general mechanism to abstract the storage of keys for routing protocols. To avoid misconfiguration and simplify problem determination, the router MUST verify the internal consistency of entries added to the table. Routing protocols describe how their protocol interacts with the key table including what validation MUST be performed. At a minimum, the router MUST verify:

Other checks are possible. For example the router could verify that if a key is associated with a peer, that peer is a configured peer for the specified protocol. However, this may be undesirable. It may be desirable to load a key table when some peers have not yet been configured. Also, it may be desirable to share portions of a key table across devices even when their current configuration does not require an adjacency with a particular peer in the interest of uniform configuration or preparing for fail-over.

3.2. Management of Key Table

Several management operations will be quite common. For service provider deployments the configuration management system can simply update the key table. However, for smaller deployments, efficient management operations that do not require a configuration management system are important.

As part of adding a new key it is typically desirable to set an expiration time for an old key. The management interface SHOULD provide a mechanism to easily update the expiration time for a current key used with a given peer or interface. Also when adding a key it is desirable to push the key out to nodes that will need it, allowing use for receiving packets then later enabling transmit. This can be accomplished automatically by providing a delay between when a key becomes valid for reception and transmission. However, some environments may not be able to predict when all the necessary changes will be made. In these cases having a mechanism to enable a key for sending is desirable. Management interfaces SHOULD provide an easy mechanism to update the direction of an existing key or to enable a disabled key.

Implementations SHOULD permit a configuration in which if no unexpired key is available, existing security associations continue using the expired key with which they were established. Implementations MUST support a configuration in which security associations fail if no un-expired key is available for them. See Section 6.2 for a discussion of security faults including those related to key expiration.

3.3. Interactions with Automated Key Management

Consideration is required for how an automated key management protocol will assign key IDs for group keys. All members of the group may need to use the same key ID. This requires careful coordination of global key IDs. Interactions with the peer key ID field may make this easier; this requires additional study.

Automated key management protocols also assign keys for single peers. If the key ID is global and needs to be coordinated between the receiver and transmitter, then there is complexity in key management protocols.

3.4. Virtual Routing and Forwarding Instances (VRFs)

Many core and enterprise routers support multiple routing instances. For example a router serving multiple VPNs is likely to have a forwarding/routing instance for each of these VPNs. Each VRF will require its own routing key table.

4. Credentials and Authorization

Several methods for authentication have been proposed for KARP. The simplest is preshared keys used directly as traffic keys. In this mode, the traffic integrity keys are directly configured. This is the mode supported by most of today's routing protocols.

As discussed in [I-D.polk-saag-rtg-auth-keytable], preshared keys can be used as the input to a key derivation function (KDF) to generate traffic keys. For example the TCP Authentication Option (TCP-AO) [RFC5925] derives keys based on the initial TCP session state. Typically a KDF will combine a long-term key with public inputs exchanged as part of the protocol to form fresh session keys. A KDF could potentially be used with some inputs that are configured along with the long-term key. Also, it's possible that inputs to a KDF will be private and exchanged as part of the protocol, although this will be uncommon in KARP's uses of KDFs.

Preshared keys could also be used by an automated key management protocol. In this mode, preshared keys would be used for authentication. However traffic keys would be generated by some key agreement mechanism or transported in a key encryption key derived from the preshared key. This mode may provide better replay protection. Also, in the absence of active attackers, key agreement strategies such as Diffie-Hellman can be used to produce high-quality traffic keys even from relatively weak preshared keys. These key-agreement mechanisms are valuable even when active attackers are present, although an active attacker can mount a man-in-the-middle attack if the preshared key is sufficiently weak.

Public keys can be used for authentication within an automated key management protocol. The design guide [I-D.ietf-karp-design-guide] describes a mode in which routers have the hashes of peer routers' public keys. In this mode, a traditional public-key infrastructure is not required. The advantage of this mode is that a router only contains its own keying material, limiting the scope of a compromise. The disadvantage is that when a router is added or deleted from the set of authorized routers, all routers that peer need to be updated. Note that self-signed certificates are a common way of communicating public-keys in this style of authentication.

Certificates signed by a certification authority or some other PKI could be used for authentication within an automated key management protocol. The advantage of this approach is that routers may not need to be directly updated when peers are added or removed. The disadvantage is that more complexity and cost is required.

Each of these approaches has a different set of management and operational requirements. Key differences include how authorization is handled and how identity works. This section discusses these differences.

4.1. Preshared Keys

In the protocol, manual preshared keys are either unnamed or named by a small integer (typically 16 or 32 bits) key ID. Implementations that support multiple keys for protocols that have no names for keys need to try all possible keys before deciding a packet cannot be validated [RFC4808]. Typically key IDs are names used by one group or peer.

Manual preshared keys are often known by a group of peers rather than just one other peer. This is an interesting security property: unlike with digitally signed messages or protocols where symmetric keys are known only to two parties, it is impossible to identify the peer sending a message cryptographically. However, it is possible to show that the sender of a message is one of the parties who knows the preshared key. Within the routing threat model the peer sending a message can be identified only because peers are trusted and thus can be assumed to correctly label the packets they send. This contrasts with a protocol where cryptographic means such as digital signatures are used to verify the origin of a message. As a consequence, authorization is typically based on knowing the preshared key rather than on being a particular peer. Note that once an authorization decision is made, the peer can assert its identity; this identity is trusted just as the routing information from the peer is trusted. Doing an additional check for authorization based on the identity included in the packet would provide little value: an attacker who somehow had the key could claim the identity of an authorized peer and an attacker without the key should be unable to claim the identity of any peer. Such a check is not required by the KARP threat model: inside attacks are not in scope.

Preshared keys used with key derivation function similarly to manual preshared keys. However to form the actual traffic keys, session or peer specific information is combined with the key. From an authorization standpoint, the derivation key works the same as a manual key. An additional routing protocol step or transport step forms the key that is actually used.

Preshared keys that are used via automatic key management have not been specified for KARP. Their naming and authorization may differ from existing uses of preshared keys in routing protocols. In particular, such keys may end up being known only by two peers. Alternatively they may also be known by a group of peers. Authorization could potentially be based on peer identity, although it is likely that knowing the right key will be sufficient. There does not appear to be a compelling reason to decouple the authorization of a key for some purpose from authorization of peers holding that key to perform the authorized function.

4.1.1. Sharing Keys and Zones of Trust

Care needs to be taken when symmetric keys are used for multiple purposes. Consider the implications of using the same preshared key for two interfaces: it becomes impossible to cryptographically distinguish a router on one interface from a router on another interface. So, a router that is trusted to participate in a routing protocol on one interface becomes implicitly trusted for the other interfaces that share the key. For many cases, such as link-state routers in the same routing area, there is no significant advantage that an attacker could gain from this trust within the KARP threat model. However, other protocols such as BGP and RIP, permit routes to be filtered across a trust boundary. For these protocols, participation in one interface might be more advantageous than another. Operationally, when this trust distinction is important to a deployment, different keys need to be used on each side of the trust boundary. Key derivation can help prevent this problem in cases of accidental misconfiguration. However, key derivation cannot protect against a situation where a system was incorrectly trusted to have the key used to perform the derivation. This question of trust is important to the KARP threat model because it is essential to determining whether a party is an insider for a particular routing protocol. A customer router that is an an insider for a BGP peering relationship with a service provider is not typically an insider when considering the security of that service provider's IGP. Similarly, To the extent that there are multiple zones of trust and a routing protocol is determining whether a particular router is within a certain zone, the question of untrusted actors is within the scope of the routing threat model.

Key derivation can be part of a management solution to a desire to have multiple keys for different zones of trust. A master key could be combined with peer, link or area identifiers to form a router-specific preshared key that is loaded onto routers. Provided that the master key lives only on the management server and not the individual routers, trust is preserved. However in many cases, generating independent keys for the routers and storing the result is more practical. If the master key were somehow compromised, all the resulting keys would need to be changed. However if independent keys are used, the scope of a compromise may be more limited.

4.1.2. Key Separation and Protocol Design

More subtle problems with key separation can appear in protocol design. Two protocols that use the same traffic keys may work together in unintended ways permitting one protocol to be used to attack the other. Consider two hypothetical protocols. Protocol A starts its messages with a set of extensions that are ignored if not understood. Protocol B has a fixed header at the beginning of its messages but ends messages with extension information. It may be that the same message is valid both as part of protocol A and protocol B. An attacker may be able to gain an advantage by getting a router to generate this message with one protocol under situations where the other protocol would not generate the message. This hypothetical example is overly simplistic; real-world attacks exploiting key separation weaknesses tend to be complicated and involve specific properties of the cryptographic functions involved. The key point is that whenever the same key is used in multiple protocols, attacks may be possible. All the involved protocols need to be analyzed to understand the scope of potential attacks.

Key separation attacks interact with the KARP operational model in a number of ways. Administrators need to be aware of situations where using the same manual traffic key with two different protocols (or the same protocol in different contexts) creates attack opportunities. Design teams should consider how their protocol might interact with other routing protocols and describe any attacks discovered so that administrators can understand the operational implications. When designing automated key management or new cryptographic authentication within routing protocols, we need to be aware that administrators expect to be able to use the same preshared keys in multiple contexts. As a result, we should use appropriate key derivation functions so that different cryptographic keys are used even when the same initial input key is used.

4.2. Asymmetric Keys

Outside of a PKI, public keys are expected to be known by the hash of a key or (potentially self-signed) certificate. The Session Description Protocol provides a standardized mechanism for naming keys (in that case certificates) based on hashes (section 5 [RFC4572]). KARP SHOULD adopt this approach or another approach already standardized within the IETF rather than inventing a new mechanism for naming public keys.

A public key is typically expected to belong to one peer. As a peer generates new keys and retires old keys, its public key may change. For this reason, from a management standpoint, peers should be thought of as associated with multiple public keys rather than as containing a single public key hash as an attribute of the peer object.

Authorization of public keys could be done either by key hash or by peer identity. Performing authorizations by peer identity should make it easier to update the key of a peer without risk of losing authorizations for that peer. However management interfaces need to be carefully designed to avoid making this extra level of indirection complicated for operators.

4.3. Public Key Infrastructure

When a PKI is used, certificates are used. The certificate binds a key to a name of a peer. The key management protocol is responsible for exchanging certificates and validating them to a trust anchor.

Authorization needs to be done in terms of peer identities not in terms of keys. One reason for this is that when a peer changes its key, the new certificate needs to be sufficient for authentication to continue functioning even though the key has never been seen before.

Potentially authorization could be performed in terms of groups of peers rather than single peers. An advantage of this is that it may be possible to add a new router with no authentication related configuration of the peers of that router. For example, a domain could decide that any router with a particular keyPurposeID signed by the organization's certificate authority is permitted to join the IGP. Just as in configurations where cryptographic authentication is not used, automatic discovery of this router can establish appropriate adjacencies.

Assuming that self-signed certificates are used by routers that wish to use public keys but that do not need a PKI, then PKI and the infrastructureless mode of public-key operation described in the previous section can work well together. One router could identify its peers based on names and use certificate validation. Another router could use hashes of certificates. This could be very useful for border routers between two organizations. Smaller organizations could use public keys and larger organizations could use PKI.

4.4. The role of Central Servers

An area to explore is the role of central servers like RADIUS or directories. As discussed in the design-guide, a system where keys are pushed by a central management system is undesirable as an end result for KARP. However central servers may play a role in authorization and key rollover. For example a node could send a hash of a public key to a RADIUS server.

If central servers do play a role it will be critical to make sure that they are not required during routine operation or a cold-start of a network. They are more likely to play a role in enrollment of new peers or key migration/compromise.

Another area where central servers may play a role is for group key agreement. As an example, [I-D.liu-ospfv3-automated-keying-req] discusses the potential need for key agreement servers in OSPF. Other routing protocols that use multicast or broadcast such as IS-IS are likely to need a similar approach. Multicast key agreement protocols need to allow operators to choose which key servers will generate traffic keys. The quality of random numbers [RFC4086] is likely to differ between systems. As a result, operators may have preferences for where keys are generated.

5. Grouping Peers Together

One significant management consideration will be the grouping of management objects necessary to determine who is authorized to act as a peer for a given routing action. As discussed previously, the following objects are potentially required:

Establishing a management model is difficult because of the complex relationships between each set of objects. As discussed there may be more than one key for a peer. However in the preshared key case, there may be more than one peer for a key. This is true both for group security association protocols such as an IGP or one-to-one protocols where the same key is used administratively. In some of these situations, it may be undesirable to explicitly enumerate the peers in the configuration; for example IGP peers are auto-discovered for broadcast links but not for non-broadcast multi-access links.

Peers may be identified either by name or key. If peers are identified by key it is strongly desirable from an operational standpoint to consider any peer identifiers or name to be a local matter and not require the names or identifiers to be synchronized. Obviously if peers are identified by names (for example with certificates in a PKI), identifiers need to be synchronized between the authorized peer and the peer making the authorization decision.

In many cases peers will explicitly be identified in routing protocol configuration. In these cases it is possible to attach the authorization information (keys or identifiers) to the peer's configuration object. Two cases do not involve enumerating peers. The first is the case where preshared keys are shared among a group of peers. It is likely that this case can be treated from a management standpoint as a single peer representing all the peers that share the keys. The other case is one where certificates in a PKI are used to introduce peers to a router. In this case, rather than configuring peers, , the router needs to be configured with information on what certificates represent acceptable peers.

Another consideration is what routing protocols share peers. For example it may be common for LDP peers to also be peers of some other routing protocol. Also, RSVP-TE may be associated with some TE-based IGP. In some of these cases it would be desirable to use the same authorization information for both routing protocols.

Finally, as discussed in Section 7, it is sometimes desirable to override some aspect of the configuration for a peer in a group. As an example, when rotating to a new key, it is desirable to be able to roll that key out to each peer that will use the key even if in the stable state the key is configured for a peer group.

In order to develop a management model for authorization, the working group needs to consider several questions. What protocols support auto-discovery of peers? What protocols require more configuration of a peer than simply the peer's authorization information and network address? What management operations are going to be common as security information for peers is configured and updated? What operations will be common while performing key transitions or while migrating to new security technologies?

6. Administrator Involvement

One key operational question is what areas will administrator involvement be required. Likely areas where involvement may be useful include enrollment of new peers. Fault recovery should also be considered.

6.1. Enrollment

One area where the management of routing security needs to be optimized is the deployment of a new router. In some cases a new router may be deployed on an existing network where routing to management servers is already available. In other cases, routers may be deployed as part of connecting or creating a site. Here, the router and infrastructure may not be available until the router has securely authenticated.

In general, security configuration can be treated as an additional configuration item that needs to be set up to establish service. There is no significant security value in protecting routing protocol keys more than administrative password or Authentication, Authorization and Accounting (AAA) secrets that can be used to gain login access to a router. These existing secrets can be used to make configuration changes that impact routing protocols as much as disclosure of a routing protocol key. Operators already have procedures in place for these items. So, it is appropriate to use similar procedures for routing protocol keys. It is reasonable to improve existing configuration procedures and the routing protocol procedures over time. However it is more desirable to deploy KARP with security similar to that used for managing existing secrets than to delay deploying KARP.

Operators MAY develop higher assurance procedures for dealing with keys. For example, asymmetric keys can be generated on a router and never exported from the router. Operators can evaluate the cost vs security and availability tradeoffs of these procedures.

6.2. Handling Faults

Faults may interact with operational practice in at least two ways. First, security solutions may introduce faults. For example if certificates expire in a PKI, previous adjacencies may no longer form. Operational practice will require a way of repairing these errors. This may end up being very similar to repairing other faults that can partition a network.

Notifications will play a critical role in avoiding security faults. Implementations SHOULD use appropriate mechanisms to notify operators as security resources are about to expire. Notifications can include messages to consoles, logged events, SNMP traps, or notifications within a routing protocol. One strategy is to have increasing escalations of notifications.

Monitoring will also play an important role in avoiding security faults such as certificate expiration. Some classes of security fault, including issues with certificates, will affect only key management protocols. other security faults can affect routing protocols directly. However, the protocols MUST still have adequate operational mechanisms to recover from these situations. Also, some faults, such as those resulting from a compromise or actual attack on a facility are inherent and may not be prevented.

A second class of faults is equipment faults that impact security. For example if keys are stored on a router and never exported from that device, failure of a router implies a need to update security provisioning on the replacement router and its peers.

One approach, recommended by work on securing BGP [I-D.ietf-sidr-rtr-keying] is to maintain the router's keying material so that when a router is replaced the same keys can be used. Router keys can be maintained on a central server. These approaches permit the credentials of a router to be recovered. This provides valuable options in case of hardware fault. The failing router can be recovered without changing credentials on other routers or waiting for keys to be certified. One disadvantage of this approach is that even if public-key cryptography is used, the private keys are located on more than just the router. a system in which keys were generated on a router and never exported from that router would typically make it more difficult for an attacker to obtain the keys. For most environments the ability to quickly replace a router justifies maintaining keys centrally.

More generally keying is another item of configuration that needs to be restored to restore service when equipment fails. Operators typically perform the minimal configuration necessary to get a router back in contact with the management server. The same would apply for keys. Operators who do not maintain copies of key material for performing key recovery on routers would need to perform a bit more work to regain contact with the management server. It seems reasonable to assume that management servers will be able to cause keys to be generated or distributed sufficiently to fully restore service.

7. Upgrade Considerations

It needs to be possible to deploy automated key management in an organization without either having to disable existing security or disrupting routing. As a result, it needs to be possible to perform a phased upgrade from manual keying to automated key management. This upgrade procedure needs to be easy and have a very low risk of disrupting routing. Today, many operators do not update keys because the perceived risk of an attack is lower than the complexity of and update and risk of routing disruptions.

For peer-to-peer protocols such as BGP, this can be relatively easy. First, code that supports automated key management needs to be loaded on both peers. Then the adjacency can be upgraded. The configuration can be updated to switch to automated key management when the second router reboots. Alternatively, if the key management protocols involved can detect that both peers now support automated key management, then a key can potentially be negotiated for an existing session.

The situation is more complex for organizations that have not upgraded from TCP MD5 [RFC2385] to the TCP Authentication Option [RFC5925]. Today, routers typically need to understand whether a given peer supports TCP MD5 or TCP-AO before opening a TCP connection. In addition, many implementations support grouping configuration of related peers including security configuration together. Implementations make it challenging to move from TCP-MD5 to TCP-AO before all peers in the group are ready. Operators perceive it as high risk to update the configuration of a large number of peers. One particularly risky situation is upgrading the configuration of iBGP peers.

The situation is more complicated for multicast protocols. It's typically not desirable to bring down an entire link to reconfigure it as using automated key management. Two approaches should be considered. One is to support key table rows supporting the automated key management and manually configured keying for the same link at the same time. Coordinating this may be challenging from an operational standpoint. Another possibility is for the automated key management protocol to actually select the same traffic key that is being used manually. This could be accomplished by having an option in the key management protocol to export the current manual group key through the automated key management protocol. Then after all nodes are configured with automated key management, manual key entries can be removed. The next re-key after all nodes have manual entries removed will generate a new fresh key. Group key management protocols are RECOMMENDED to support an option to export existing manual keys during initial deployment of automated key management.

8. Security Considerations

This document does not define a protocol. It does discuss the operational and management implications of several security technologies.

9. IANA Considerations

This document has no actions for IANA.

10. Acknowledgments

Funding for Sam Hartman's work on this memo is provided by Huawei.

The authors would like to thank Bill Atwood , Randy Bush, Wes George, Gregory Lebovitz, and Russ White for valuable reviews.

11. References

11.1. Normative References

[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997.
[I-D.ietf-karp-crypto-key-table] Housley, R., Polk, T., Hartman, S. and D. Zhang, "Database of Long-Lived Symmetric Cryptographic Keys", Internet-Draft draft-ietf-karp-crypto-key-table-05, February 2013.

11.2. Informative References

[I-D.liu-ospfv3-automated-keying-req] Liu, Y., "OSPFv3 Automated Group Keying Requirements", Internet-Draft draft-liu-ospfv3-automated-keying-req-01, July 2007.
[I-D.ietf-karp-design-guide] Lebovitz, G. and M. Bhatia, "Keying and Authentication for Routing Protocols (KARP) Design Guidelines", Internet-Draft draft-ietf-karp-design-guide-10, December 2011.
[RFC2328] Moy, J., "OSPF Version 2", STD 54, RFC 2328, April 1998.
[RFC4808] Bellovin, S., "Key Change Strategies for TCP-MD5", RFC 4808, March 2007.
[RFC4572] Lennox, J., "Connection-Oriented Media Transport over the Transport Layer Security (TLS) Protocol in the Session Description Protocol (SDP)", RFC 4572, July 2006.
[I-D.polk-saag-rtg-auth-keytable] Polk, T. and R. Housley, "Routing Authentication Using A Database of Long-Lived Cryptographic Keys", Internet-Draft draft-polk-saag-rtg-auth-keytable-05, November 2010.
[RFC5925] Touch, J., Mankin, A. and R. Bonica, "The TCP Authentication Option", RFC 5925, June 2010.
[I-D.ietf-sidr-rtr-keying] Turner, S., Patel, K. and R. Bush, "Router Keying for BGPsec", Internet-Draft draft-ietf-sidr-rtr-keying-01, February 2013.
[RFC2385] Heffernan, A., "Protection of BGP Sessions via the TCP MD5 Signature Option", RFC 2385, August 1998.
[RFC4086] Eastlake, D., Schiller, J. and S. Crocker, "Randomness Requirements for Security", BCP 106, RFC 4086, June 2005.

Authors' Addresses

Sam Hartman Painless Security EMail: hartmans-ietf@mit.edu
Dacheng Zhang Huawei EMail: zhangdacheng@huawei.com