draft-ietf-adslmib-adsl2-08.txt   rfc4706.txt 
Network Working Group M. Morgenstern Network Working Group M. Morgenstern
Internet-Draft M. Dodge Request for Comments: 4706 M. Dodge
Expires: December 13, 2006 ECI Telecom Ltd. Category: Standards Track ECI Telecom Ltd.
S. Baillie S. Baillie
U. Bonollo U. Bonollo
NEC Australia NEC Australia
June 11, 2006 November 2006
Definitions of Managed Objects for Asymmetric Digital Subscriber Line 2
(ADSL2)
draft-ietf-adslmib-adsl2-08.txt
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at Definitions of Managed Objects for
http://www.ietf.org/ietf/1id-abstracts.txt. Asymmetric Digital Subscriber Line 2 (ADSL2)
The list of Internet-Draft Shadow Directories can be accessed at Status of This Memo
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on December 13, 2006. This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice Copyright Notice
Copyright (C) The Internet Society (2006). Copyright (C) The Internet Society (2006).
Abstract Abstract
This document defines a Management Information Base (MIB) module for This document defines a Management Information Base (MIB) module for
use with network management protocols in the Internet community. In use with network management protocols in the Internet community. In
particular, it describes objects used for managing parameters of the particular, it describes objects used for managing parameters of the
"Asymmetric Digital Subscriber Line" family of interface types, "Asymmetric Digital Subscriber Line" family of interface types: ADSL,
especially including ADSL, ADSL2, and ADSL2+. ADSL2, ADSL2+, and their variants.
Table of Contents Table of Contents
1. The Internet-Standard Management Framework . . . . . . . . . 3 1. The Internet-Standard Management Framework ......................3
2. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Overview ........................................................3
2.1. Relationship to other MIBs . . . . . . . . . . . . . . . 4 2.1. Relationship to Other MIBs .................................4
2.2. IANA Considerations . . . . . . . . . . . . . . . . . . . 6 2.1.1. General IF-MIB Integration (RFC 2863) ...............4
2.3. Conventions Used in the MIB Module . . . . . . . . . . . 6 2.1.2. Usage of ifTable ....................................5
2.4. Structure . . . . . . . . . . . . . . . . . . . . . . . . 12 2.2. IANA Considerations ........................................6
2.5. Persistence . . . . . . . . . . . . . . . . . . . . . . . 15 2.3. Conventions Used in the MIB Module .........................6
2.6. Line Topology . . . . . . . . . . . . . . . . . . . . . . 17 2.3.1. Naming Conventions ..................................6
2.7. Counters, Interval Buckets, and Thresholds . . . . . . . 18 2.3.2. Textual Conventions .................................7
2.8. Profiles . . . . . . . . . . . . . . . . . . . . . . . . 20 2.4. Structure .................................................12
2.9. Notifications . . . . . . . . . . . . . . . . . . . . . . 23 2.5. Persistence ...............................................15
3. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 25 2.6. Line Topology .............................................17
4. Implementation Analysis . . . . . . . . . . . . . . . . . . . 154 2.7. Counters, Interval Buckets, and Thresholds ................18
5. Security Considerations . . . . . . . . . . . . . . . . . . . 155 2.7.1. Counters Managed ...................................18
6. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 162 2.7.2. Minimum Number of Buckets ..........................19
7. References . . . . . . . . . . . . . . . . . . . . . . . . . 163 2.7.3. Interval Buckets Initialization ....................19
7.1. Normative References . . . . . . . . . . . . . . . . . . 163 2.7.4. Interval Buckets Validity ..........................19
7.2. Informative References . . . . . . . . . . . . . . . . . 164 2.8. Profiles ..................................................20
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 165 2.8.1. Configuration Profiles and Templates ...............21
Intellectual Property and Copyright Statements . . . . . . . . . 166 2.8.2. Alarm Configuration Profiles and Templates .........22
2.8.3. Managing Profiles and Templates ....................22
2.8.4. Managing Multiple Bearer Channels ..................23
2.9. Notifications .............................................24
3. Definitions ....................................................25
4. Implementation Analysis .......................................155
5. Security Considerations .......................................155
6. Acknowledgements ..............................................163
7. References ....................................................163
7.1. Normative References .....................................163
7.2. Informative References ...................................165
1. The Internet-Standard Management Framework 1. The Internet-Standard Management Framework
For a detailed overview of the documents that describe the current For a detailed overview of the documents that describe the current
Internet-Standard Management Framework, please refer to Section 7 of Internet-Standard Management Framework, please refer to Section 7 of
RFC 3410 [RFC3410]. RFC 3410 [RFC3410].
Managed objects are accessed via a virtual information store, termed Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. MIB objects are generally the Management Information Base or MIB. MIB objects are generally
accessed through the Simple Network Management Protocol (SNMP). accessed through the Simple Network Management Protocol (SNMP).
Objects in the MIB are defined using the mechanisms defined in the Objects in the MIB are defined using the mechanisms defined in the
Structure of Management Information (SMI). This memo specifies a MIB Structure of Management Information (SMI). This memo specifies a MIB
module that is compliant to the SMIv2, which is described in STD 58, module that is compliant to the SMIv2, which is described in STD 58,
RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
[RFC2580]. [RFC2580].
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
2. Overview 2. Overview
This document defines a Management Information Base (MIB) module for This document defines a Management Information Base (MIB) module for
use with network management protocols in the Internet community for use with network management protocols in the Internet community for
the purpose of managing ADSL, ADSL2, and ADSL2+ lines. the purpose of managing ADSL, ADSL2, and ADSL2+ lines.
The MIB module described in RFC 2662 [RFC2662] describes objects used The MIB module described in RFC 2662 [RFC2662] describes objects used
for managing Asymmetric Bit-Rate DSL (ADSL) interfaces per for managing Asymmetric Bit-Rate DSL (ADSL) interfaces per
[T1E1.413], [G.992.1], and [G.992.2]. These object descriptions are [T1E1.413], [G.992.1], and [G.992.2]. These object descriptions are
based upon the specifications for the ADSL Embedded Operations based upon the specifications for the ADSL Embedded Operations
skipping to change at page 3, line 48 skipping to change at page 3, line 44
This document does not obsolete RFC 2662 [RFC2662], but rather This document does not obsolete RFC 2662 [RFC2662], but rather
provides a more comprehensive management model that includes the provides a more comprehensive management model that includes the
ADSL2 and ADSL2+ technologies per G.992.3, G.992.4, and G.992.5 ADSL2 and ADSL2+ technologies per G.992.3, G.992.4, and G.992.5
([G.992.3], [G.992.4], and [G.992.5] respectively). In addition, ([G.992.3], [G.992.4], and [G.992.5] respectively). In addition,
objects have been added to improve the management of ADSL, ADSL2, and objects have been added to improve the management of ADSL, ADSL2, and
ADSL2+ lines. ADSL2+ lines.
Additionally, the management framework for New Generation ADSL lines Additionally, the management framework for New Generation ADSL lines
specified [TR-90] by the Digital Subscriber Line Forum (DSLF) has specified [TR-90] by the Digital Subscriber Line Forum (DSLF) has
been taken into consideration. That framework is based on ITU-T been taken into consideration. That framework is based on ITU-T
G.997.1 standard [G.997.1] as well as on two amendments: ([G.997.1 G.997.1 standard [G.997.1] as well as on two amendments:
am1] and [G.997.1 am2]). This document refers to all three documents ([G.997.1am1] and [G.997.1am2]). This document refers to all three
as G.997.1. That is, a MIB attribute whose REFERENCE section documents as G.997.1. That is, a MIB attribute whose REFERENCE
provides a paragraph number in ITU-T G.997.1 is actually originated section provides a paragraph number in ITU-T G.997.1 is actually
from either G.997.1 [G.997.1] or one of its amendment documents. originated from either G.997.1 [G.997.1] or one of its amendment
documents.
Note that future revision of ITU-T G.997.1 standard will refer also Note that the revised ITU-T G.997.1 standard also refers to the next
to next generation of VDSL technology, known as VDSL2, per ITU-T generation of VDSL technology, known as VDSL2, as per ITU-T G.993.2
G.993.2 [G.993.2]. However, managing VDSL2 lines is currently beyond [G.993.2]. However, managing VDSL2 lines is currently beyond the
the scope of the MIB this document specifies. scope of this document.
The MIB module is located in the MIB tree under MIB 2 transmission, The MIB module is located in the MIB tree under MIB 2 transmission,
as discussed in the IANA Considerations section of this document. as discussed in the IANA Considerations section of this document.
2.1. Relationship to other MIBs The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
2.1. Relationship to Other MIBs
This section outlines the relationship of this MIB module with other This section outlines the relationship of this MIB module with other
MIB modules described in RFCs. Specifically, IF-MIB as presented in MIB modules described in RFCs. Specifically, IF-MIB as presented in
RFC 2863 [RFC2863] is discussed. RFC 2863 [RFC2863] is discussed.
2.1.1. General IF-MIB Integration (RFC 2863) 2.1.1. General IF-MIB Integration (RFC 2863)
The ADSL2 Line MIB specifies the detailed attributes of a data The ADSL2 Line MIB specifies the detailed attributes of a data
interface. As such, it needs to integrate with RFC 2863 [RFC2863]. interface. As such, it needs to integrate with RFC 2863 [RFC2863].
The IANA has assigned the following ifTypes, which may be applicable The IANA has assigned the following ifTypes, which may be applicable
for ADSL lines: for ADSL lines:
IANAifType ::= TEXTUAL-CONVENTION IANAifType ::= TEXTUAL-CONVENTION
... ...
SYNTAX INTEGER { SYNTAX INTEGER {
... ...
channel(70), -- channel channel(70), -- Channel
ADSL (94), -- Asymmetric Digital Subscriber Loop adsl(94), -- Asymmetric Digital Subscriber Loop
... ...
Interleave(124), -- Interleaved Channel interleave(124), -- Interleaved Channel
Fast(125), -- Fast Channel fast(125), -- Fast Channel
... ...
ADSL2 (230), -- Asymmetric Digital Subscriber Loop 2 adsl2plus(238), -- Asymmetric Digital Subscriber Loop Version 2,
Version 2 Plus, and all variants
... ...
} }
ADSL lines that are identified with ifType=ADSL (94) MUST be managed ADSL lines that are identified with ifType=adsl(94) MUST be managed
with the MIB specified by RFC2662. ADSL, ADSL2, and ADSL2+ lines with the MIB specified by RFC2662. ADSL, ADSL2, and ADSL2+ lines
identified with ifType=ADSL2 (230) MUST be managed with the MIB identified with ifType=adsl2plus(238) MUST be managed with the MIB
specified by this document. specified by this document.
In any case, the SNMP agent may use either ifType=Interleave (124) or In any case, the SNMP agent may use either ifType=interleave(124) or
Fast (125) for each channel, e.g., depending on whether or not it is fast(125) for each channel, e.g., depending on whether or not it is
capable of using an interleaver on that channel. It may use the capable of using an interleaver on that channel. It may use the
ifType=channel (70) when all channels are capable of using an ifType=channel (70) when all channels are capable of using an
interleaver (e.g., for ADSL2 xtus). interleaver (e.g., for ADSL2 XTUs).
Note that the ifFixedLengthGroup from RFC 2863 [RFC2863] MUST be Note that the ifFixedLengthGroup from RFC 2863 [RFC2863] MUST be
supported and that the ifRcvAddressGroup does not apply to this MIB supported and that the ifRcvAddressGroup does not apply to this MIB
module. module.
2.1.2. Usage of ifTable 2.1.2. Usage of ifTable
The MIB branch identified by ifType contains tables appropriate for The MIB branch identified by ifType contains tables appropriate for
the interface types described above. Most such tables extend the the interface types described above. Most such tables extend the
ifEntry table, and are indexed by ifIndex. For interfaces in systems ifEntry table and are indexed by ifIndex. For interfaces in systems
implementing this MIB module, those table entries indexed by ifIndex implementing this MIB module, those table entries indexed by ifIndex
MUST be persistent. MUST be persistent.
The following attributes are part of the mandatory The following attributes are part of the mandatory
ifGeneralInformationGroup in the Interfaces MIB [RFC2863], and are ifGeneralInformationGroup in the Interfaces MIB [RFC2863] and are not
not duplicated in the ADSL2 Line MIB. duplicated in the ADSL2 Line MIB.
=================================================================== ===================================================================
ifIndex Interface index. ifIndex Interface index.
ifDescr See interfaces MIB. ifDescr See interfaces MIB.
ifType ADSL2 (230) or ifType adsl2plus(238) or
Channel (70) or channel(70) or
Interleave (124) or interleave(124) or
Fast (125) fast(125).
ifSpeed Set as appropriate. ifSpeed Set as appropriate.
ifPhysAddress This object MUST have an octet string ifPhysAddress This object MUST have an octet string
with zero length. with zero length.
ifAdminStatus See interfaces MIB. ifAdminStatus See interfaces MIB.
ifOperStatus See interfaces MIB. ifOperStatus See interfaces MIB.
skipping to change at page 6, line 10 skipping to change at page 6, line 16
ifHighSpeed Set as appropriate. ifHighSpeed Set as appropriate.
ifConnectorPresent Set as appropriate. ifConnectorPresent Set as appropriate.
=================================================================== ===================================================================
Figure 1: Use of ifTable Objects Figure 1: Use of ifTable Objects
2.2. IANA Considerations 2.2. IANA Considerations
The ADSL2-LINE-MIB module requires the allocation of a new ifType The IANA has allocated ifType=adsl2plus(238) for Asymmetric Digital
value for Asymmetric Digital Subscriber Loop Version 2, to Subscriber Loop Version 2. A separate ifType number was necessary to
distinguish between ADSL lines that are managed with the RFC2662 distinguish between ADSL lines that are managed with the RFC2662
management model and ADSL/ADSL2 and ADSL2+ lines managed with the management model and ADSL/ADSL2 and ADSL2+ lines managed with the
model defined in this document. model defined in this document.
Also the ADSL2-LINE-MIB module requires the allocation of a single Also, the IANA has assigned transmission number 238 to the
object identifier for its MODULE-IDENTITY. The IANA should allocate ADSL2-LINE-MIB module.
this object identifier in the transmission subtree.
An assignment was in fact done when RFC 2662 was published, but as An assignment was in fact done when RFC 2662 was published, but as
this MIB does not obsolete RFC 2662, it requires new assignment from this MIB does not obsolete RFC 2662, it required a new assignment
IANA. from IANA.
2.3. Conventions Used in the MIB Module 2.3. Conventions Used in the MIB Module
2.3.1. Naming Conventions 2.3.1. Naming Conventions
AtuC A central site terminal unit ATU ADSL Transceiver Unit
AtuR A remote site terminal unit ATU-C ATU at the Central office end (i.e., network operator).
ATU-R ATU at the Remote end (i.e., subscriber end of the loop).
xtu A terminal unit; either an AtuC or AtuR XTU A terminal unit; either an ATU-C or an ATU-R.
CRC Cyclical redundancy check CRC Cyclic Redundancy Check
DELT Dual Ended Loop Test DELT Dual Ended Loop Test
ES Errored second ES Errored Second
FEC Forward Error Correction FEC Forward Error Correction
LOF Loss of framing LOF Loss Of Frame
LOS Loss of signal LOS Loss Of Signal
LOSS LOS Second LOSS LOS Seconds
SES Severely-errored second SES Severely-Errored Second
SNR Signal-to-noise ratio SNR Signal-to-Noise Ratio
UAS Unavailable second UAS Unavailable Seconds
2.3.2. Textual Conventions 2.3.2. Textual Conventions
The following textual conventions are defined to reflect the line The following textual conventions are defined to reflect the line
topology in the MIB module (further discussed in the following topology in the MIB module (further discussed in the following
section), the various transmission modes, power states, section), the various transmission modes, power states,
synchronization states, possible values for various configuration synchronization states, possible values for various configuration
parameters, status parameters, and other parameter types. parameters, status parameters, and other parameter types.
o Adsl2Unit: o Adsl2Unit:
Attributes with this syntax uniquely identify each unit in the Attributes with this syntax uniquely identify each unit in the
ADSL/ADSL2/ADSL2+ link. It mirrors the EOC addressing mechanism: ADSL/ADSL2/ADSL2+ link. It mirrors the EOC addressing mechanism:
atuc(1) - central office (CO) terminal unit atuc(1) - Central office ADSL transceiver unit (ATU-C).
atur(2) - customer premises equipment (CPE) atur(2) - Remote ADSL transceiver unit (ATU-R).
terminal unit
o Adsl2Direction: o Adsl2Direction:
Attributes with this syntax uniquely identify a transmission Attributes with this syntax uniquely identify a transmission
direction in an ADSL/ADSL2/ADSL2+ link. Upstream direction is a direction in an ADSL/ADSL2/ADSL2+ link. Upstream direction is a
transmission from the customer premises equipment (CPE) towards transmission from the remote end (ATU-R) towards the central
the central office (CO), while downstream direction is a office end (ATU-C), while downstream direction is a transmission
transmission from the CO towards the CPE. from the ATU-C towards the ATU-R.
upstream(1) - Transmission from the CPE to the CO upstream(1) - Transmission from the ATU-R to the ATU-C.
downstream(2) - Transmission from the CO to the CPE downstream(2) - Transmission from the ATU-C to the ATU-R.
o Adsl2TransmissionModeType: o Adsl2TransmissionModeType:
Attributes with this syntax reference the list of possible Attributes with this syntax reference the list of possible
transmission modes for ADSL/ADSL2 or ADSL2+. transmission modes for ADSL/ADSL2 or ADSL2+.
Specified as a BITS construct, there are currently a few dozen Specified as a BITS construct, there are currently a few dozen
transmission modes in the list. transmission modes in the list.
o Adsl2RaMode: o Adsl2RaMode:
skipping to change at page 7, line 44 skipping to change at page 8, line 4
Attributes with this syntax reference if and how Rate-Adaptive Attributes with this syntax reference if and how Rate-Adaptive
synchronization is being used on the respective ADSL/ADSL2 or synchronization is being used on the respective ADSL/ADSL2 or
ADSL2+ link: ADSL2+ link:
manual (1) - No Rate-Adaptation. The initialization process manual (1) - No Rate-Adaptation. The initialization process
attempts to synchronize to a specified rate. attempts to synchronize to a specified rate.
raInit (2) - Rate-Adaptation during initialization process raInit (2) - Rate-Adaptation during initialization process
only, which attempts to synchronize to a rate only, which attempts to synchronize to a rate
between minimum and maximum specified values. between minimum and maximum specified values.
dynamicRa (3) - Dynamic Rate-Adaptation during initialization dynamicRa (3) - Dynamic Rate-Adaptation during initialization
process as well as during SHOWTIME. process as well as during SHOWTIME.
o Adsl2InitResult: o Adsl2InitResult:
Attributes with this syntax reference the recent result of a full Attributes with this syntax reference the recent result of a full
initialization attempt: initialization attempt:
noFail (0) - Successful initialization noFail(0) - Successful initialization.
configError (1) - Configuration failure configError(1) - Configuration failure.
configNotFeasible (2) - Configuration details not supported configNotFeasible(2) - Configuration details not supported.
commFail (3) - Communication failure commFail(3) - Communication failure.
noPeerAtu (4) - Peer ATU not detected noPeerAtu(4) - Peer ADSL Transceiver Unit (ATU) not
otherCause (5) - Other initialization failure reason detected.
otherCause(5) - Other initialization failure reason.
o Adsl2OperationModes: o Adsl2OperationModes:
Attributes with this syntax uniquely identify an ADSL mode, which Attributes with this syntax uniquely identify an ADSL mode, which
is a category associated with each transmission mode defined for is a category associated with each transmission mode defined for
the ADSL/ADSL2 or ADSL2+ link. Part of the line configuration the ADSL/ADSL2 or ADSL2+ link. Part of the line configuration
profile depends on the ADSL Mode: profile depends on the ADSL Mode:
Specified as an enumeration construct, there are currently a few Specified as an enumeration construct, there are currently a few
dozen transmission modes in the list. dozen transmission modes in the list.
o Adsl2PowerMngState: o Adsl2PowerMngState:
Attributes with this syntax uniquely identify each power Attributes with this syntax uniquely identify each power
management state defined for the ADSL/ADSL2 or ADSL2+ link: management state defined for the ADSL/ADSL2 or ADSL2+ link:
l0(1) - L0 - Full power management state l0(1) - L0 - Full power management state.
l1(2) - L1 - Low power management state (for G.992.2) l1(2) - L1 - Low power management state (for G.992.2).
l2(3) - L2 - Low power management state (for G.992.3, l2(3) - L2 - Low power management state (for G.992.3,
G.992.4, and G.992.5) G.992.4, and G.992.5).
l3(4) - L3 - Idle power management state l3(4) - L3 - Idle power management state.
o Adsl2ConfPmsForce: o Adsl2ConfPmsForce:
Attributes with this syntax are configuration parameters that Attributes with this syntax are configuration parameters that
reference the desired power management state for the ADSL/ADSL2 or reference the desired power management state for the ADSL/ADSL2 or
ADSL2+ link: ADSL2+ link:
l3toL0 (0) - Perform a transition from L3 to L0 (Full l3toL0 (0) - Perform a transition from L3 to L0 (Full
power management state) power management state).
l0toL2 (2) - Perform a transition from L0 to L2 (Low l0toL2 (2) - Perform a transition from L0 to L2 (Low
power management state) power management state).
l0orL2toL3 (3) - Perform a transition into L3 (Idle power l0orL2toL3 (3) - Perform a transition into L3 (Idle power
management state) management state).
o Adsl2LConfProfPmMode: o Adsl2LConfProfPmMode:
Attributes with this syntax are configuration parameters that Attributes with this syntax are configuration parameters that
reference the power modes/states into which the ATU-C or ATU-R may reference the power modes/states into which the ATU-C or ATU-R may
autonomously transit. autonomously transit.
This is a BITS structure that allows control of the following This is a BITS structure that allows control of the following
transit options: transit options:
allowTransitionsToIdle (0) - xTU may autonomously transit allowTransitionsToIdle(0) - XTU may autonomously transit
to idle (L3) state. to idle (L3) state.
allowTransitionsToLowPower (1)- xTU may autonomously transit allowTransitionsToLowPower(1) - XTU may autonomously transit
to low-power (L2) state. to low-power (L2) state.
o Adsl2LineLdsf: o Adsl2LineLdsf:
Attributes with this syntax are configuration parameters that Attributes with this syntax are configuration parameters that
control the Loop Diagnostic mode for the ADSL/ADSL2 or ADSL2+ control the Loop Diagnostic mode for the ADSL/ADSL2 or ADSL2+
link: link:
inhibit (0) - Inhibit Loop Diagnostic mode inhibit(0) - Inhibit Loop Diagnostic mode.
force (1) - Force/Initiate Loop Diagnostic mode force(1) - Force/Initiate Loop Diagnostic mode.
o Adsl2LdsfResult: o Adsl2LdsfResult:
Attributes with this syntax are status parameters that report the Attributes with this syntax are status parameters that report the
result of the recent Loop Diagnostic mode issued for the ADSL/ result of the recent Loop Diagnostic mode issued for the
ADSL2 or ADSL2+ link: ADSL/ADSL2 or ADSL2+ link:
none (1) - The default value, in case LDSF was never none(1) - The default value, in case loop diagnostics
requested for the associated line. mode forced (LDSF) was never requested for
the associated line.
success (2) - The recent command completed success (2) - The recent command completed
successfully. successfully.
inProgress (3) - The Loop Diagnostics process is in inProgress (3) - The Loop Diagnostics process is in
progress. progress.
unsupported (4) - The NE or the line card doesn't support unsupported (4) - The NE or the line card doesn't support
LDSF. LDSF.
cannotRun (5) - The NE cannot initiate the command, due cannotRun (5) - The NE cannot initiate the command, due
to a non specific reason. to a non specific reason.
aborted (6) - The Loop Diagnostics process aborted. aborted (6) - The Loop Diagnostics process aborted.
failed (7) - The Loop Diagnostics process failed. failed (7) - The Loop Diagnostics process failed.
skipping to change at page 9, line 41 skipping to change at page 10, line 4
progress. progress.
unsupported (4) - The NE or the line card doesn't support unsupported (4) - The NE or the line card doesn't support
LDSF. LDSF.
cannotRun (5) - The NE cannot initiate the command, due cannotRun (5) - The NE cannot initiate the command, due
to a non specific reason. to a non specific reason.
aborted (6) - The Loop Diagnostics process aborted. aborted (6) - The Loop Diagnostics process aborted.
failed (7) - The Loop Diagnostics process failed. failed (7) - The Loop Diagnostics process failed.
illegalMode (8) - The NE cannot initiate the command, due illegalMode (8) - The NE cannot initiate the command, due
to the specific mode of the relevant to the specific mode of the relevant
line. line.
adminUp (9) - The NE cannot initiate the command because adminUp (9) - The NE cannot initiate the command because
the relevant line is administratively the relevant line is administratively 'Up'.
'Up'.
tableFull (10) - The NE cannot initiate the command, due tableFull (10) - The NE cannot initiate the command, due
to reaching the maximum number of rows to reaching the maximum number of rows
in the results table. in the results table.
noResources (11) - The NE cannot initiate the command, due noResources (11) - The NE cannot initiate the command, due
to lack of internal memory resources. to lack of internal memory resources.
o Adsl2SymbolProtection: o Adsl2SymbolProtection:
Attributes with this syntax are configuration parameters that Attributes with this syntax are configuration parameters that
reference the minimum length impulse noise protection (INP) in reference the minimum-length impulse noise protection (INP) in
terms of number of symbols: terms of number of symbols:
noProtection (1) - INP not required noProtection(1) - INP not required.
halfSymbol (2) - INP length = 1/2 symbol halfSymbol(2) - INP length = 1/2 symbol.
singleSymbol (3) - INP length = 1 symbol singleSymbol(3) - INP length = 1 symbol.
twoSymbols (4) - INP length = 2 symbols twoSymbols(4) - INP length = 2 symbols.
threeSymbols (5) - INP length = 3 symbols threeSymbols(5) - INP length = 3 symbols.
fourSymbols (6) - INP length = 4 symbols fourSymbols(6) - INP length = 4 symbols.
fiveSymbols (7) - INP length = 5 symbols fiveSymbols(7) - INP length = 5 symbols.
sixSymbols (8) - INP length = 6 symbols sixSymbols(8) - INP length = 6 symbols.
sevenSymbols (9) - INP length = 7 symbols sevenSymbols(9) - INP length = 7 symbols.
eightSymbols (10) - INP length = 8 symbols eightSymbols(10) - INP length = 8 symbols.
nineSymbols (11) - INP length = 9 symbols nineSymbols(11) - INP length = 9 symbols.
tenSymbols (12) - INP length = 10 symbols tenSymbols(12) - INP length = 10 symbols.
elevenSymbols (13) - INP length = 11 symbols elevenSymbols(13) - INP length = 11 symbols.
twelveSymbols (14) - INP length = 12 symbols twelveSymbols(14) - INP length = 12 symbols.
thirteeSymbols (15)- INP length = 13 symbols thirteeSymbols(15) - INP length = 13 symbols.
fourteenSymbols (16)-INP length = 14 symbols fourteenSymbols(16) - INP length = 14 symbols.
fifteenSymbols (17)- INP length = 15 symbols fifteenSymbols(17) - INP length = 15 symbols.
sixteenSymbols (18)- INP length = 16 symbols sixteenSymbols(18) - INP length = 16 symbols.
o Adsl2MaxBer: o Adsl2MaxBer:
Attributes with this syntax are configuration parameters that Attributes with this syntax are configuration parameters that
reference the maximum Bit Error Rate (BER): reference the maximum Bit Error Rate (BER):
eminus3 (1) - Maximum BER=E^-3 eminus3(1) - Maximum BER=E^-3.
eminus5 (2) - Maximum BER=E^-5 eminus5(2) - Maximum BER=E^-5.
eminus7 (3) - Maximum BER=E^-7 eminus7(3) - Maximum BER=E^-7.
o Adsl2ScMaskDs: o Adsl2ScMaskDs:
Attributes with this syntax are configuration parameters that Attributes with this syntax are configuration parameters that
reference the downstream sub-carrier mask. It is a bitmap of up reference the downstream sub-carrier mask. It is a bitmap of up
to 512 bits. to 512 bits.
o Adsl2ScMaskUs: o Adsl2ScMaskUs:
Attributes with this syntax are configuration parameters that Attributes with this syntax are configuration parameters that
skipping to change at page 11, line 35 skipping to change at page 11, line 41
o Adsl2Tssi: o Adsl2Tssi:
Attributes with this syntax are status parameters that reference Attributes with this syntax are status parameters that reference
the transmit spectrum shaping (TSSi). It is a structure of up to the transmit spectrum shaping (TSSi). It is a structure of up to
32 breakpoints, where each breakpoint occupies 3 octets. 32 breakpoints, where each breakpoint occupies 3 octets.
o Adsl2LastTransmittedState: o Adsl2LastTransmittedState:
Attributes with this syntax reference the list of initialization Attributes with this syntax reference the list of initialization
states for ADSL/ADSL2 or ADSL2+ modems. The list of states for CO states for ADSL/ADSL2 or ADSL2+ modems. The list of states for CO
side modems is different from the list of states for the CPE side side modems (ATU-Cs) is different from the list of states for the
modems. remote side modems (ATU-Rs).
Specified as an enumeration type, there are currently a few dozen Specified as an enumeration type, there are currently a few dozen
states in the list per each unit side (i.e., CO and CPE). states in the list per each unit side (i.e., ATU-C or ATU-R).
o Adsl2LineStatus: o Adsl2LineStatus:
Attributes with this syntax are status parameters that reflect the Attributes with this syntax are status parameters that reflect the
failure status for a given endpoint of ADSL/ADSL2 or ADSL2+ link. failure status for a given endpoint of ADSL/ADSL2 or ADSL2+ link.
This is a BITS structure that can report the following failures: This is a BITS structure that can report the following failures:
noDefect (0) - This bit position positively reports that noDefect (0) - This bit position positively reports that
no defect or failure exist. no defect or failure exists.
lossOfFraming (1) - Loss of frame synchronization lossOfFrame(1) - Loss of frame synchronization.
lossOfSignal (2) - Loss of signal lossOfSignal(2) - Loss of signal.
lossOfPower (3) - Loss of power. Usually this failure may lossOfPower (3) - Loss of power. Usually this failure may
be reported for CPE units only be reported for ATU-Rs only.
initFailure (4) - Recent initialization process failed. initFailure (4) - Recent initialization process failed.
Never active on ATU-R. Never active on ATU-R.
o Adsl2ChAtmStatus: o Adsl2ChAtmStatus:
Attributes with this syntax are status parameters that reflect the Attributes with this syntax are status parameters that reflect the
failure status for Transmission Convergence (TC) layer of a given failure status for Transmission Convergence (TC) layer of a given
ATM interface (data path over an ADSL/ADSL2 or ADSL2+ link). ATM interface (data path over an ADSL/ADSL2 or ADSL2+ link).
This is a BITS structure that can report the following failures: This is a BITS structure that can report the following failures:
noDefect (0) - This bit position positively reports noDefect (0) - This bit position positively reports
that no defect or failure exist. that no defect or failure exists.
noCellDelineation (1) - The link was successfully noCellDelineation (1) - The link was successfully
initialized but cell delineation initialized but cell delineation
was never acquired on the was never acquired on the
associated ATM data path. associated ATM data path.
lossOfCellDelineation (2)- Loss of cell delineation on the lossOfCellDelineation (2)- Loss of cell delineation on the
associated ATM data path associated ATM data path.
o Adsl2ChPtmStatus: o Adsl2ChPtmStatus:
Attributes with this syntax are status parameters that reflect the Attributes with this syntax are status parameters that reflect the
failure status for a given PTM interface (packet data path over an failure status for a given PTM interface (packet data path over an
ADSL/ADSL2 or ADSL2+ link). ADSL/ADSL2 or ADSL2+ link).
This is a BITS structure that can report the following failures: This is a BITS structure that can report the following failures:
noDefect (0) - This bit position positively reports that no noDefect (0) - This bit position positively reports that no
defect or failure exist. defect or failure exists.
outOfSync (1) - Out of synchronization. outOfSync (1) - Out of synchronization.
2.4. Structure 2.4. Structure
The MIB module is structured into following MIB groups: The MIB module is structured into following MIB groups:
o Line Configuration, Maintenance, and Status Group: o Line Configuration, Maintenance, and Status Group:
This group supports MIB objects for configuring parameters for the This group supports MIB objects for configuring parameters for the
ADSL/ADSL2 or ADSL2+ line and retrieving line status information. ADSL/ADSL2 or ADSL2+ line and retrieving line status information.
skipping to change at page 13, line 5 skipping to change at page 13, line 4
outOfSync (1) - Out of synchronization. outOfSync (1) - Out of synchronization.
2.4. Structure 2.4. Structure
The MIB module is structured into following MIB groups: The MIB module is structured into following MIB groups:
o Line Configuration, Maintenance, and Status Group: o Line Configuration, Maintenance, and Status Group:
This group supports MIB objects for configuring parameters for the This group supports MIB objects for configuring parameters for the
ADSL/ADSL2 or ADSL2+ line and retrieving line status information. ADSL/ADSL2 or ADSL2+ line and retrieving line status information.
It also supports MIB objects for configuring a requested power It also supports MIB objects for configuring a requested power
state or initiating a Dual Ended Line Test (DELT) process in the state or initiating a Dual Ended Loop Test (DELT) process in the
ADSL/ADSL2 or ADSL2+ line. It contains the following table: ADSL/ADSL2 or ADSL2+ line. It contains the following table:
- adsl2LineTable - adsl2LineTable
o Channel Status Group: o Channel Status Group:
This group supports MIB objects for retrieving channel layer This group supports MIB objects for retrieving channel layer
status information. It contains the following table: status information. It contains the following table:
- adsl2ChannelStatusTable - adsl2ChannelStatusTable
o Subcarrier Status Group: o Subcarrier Status Group:
This group supports MIB objects for retrieving the sub-carrier This group supports MIB objects for retrieving the sub-carrier
layer status information, mostly collected by a Dual Ended Line layer status information, mostly collected by a Dual Ended Loop
Test (DELT) process. It contains the following table: Test (DELT) process. It contains the following table:
- adsl2SCStatusTable - adsl2SCStatusTable
o Unit Inventory Group: o Unit Inventory Group:
This group supports MIB objects for retrieving Unit inventory This group supports MIB objects for retrieving Unit inventory
information about units in ADSL/ADSL2 or ADSL2+ lines via the EOC. information about units in ADSL/ADSL2 or ADSL2+ lines via the EOC.
It contains the following table: It contains the following table:
skipping to change at page 16, line 29 skipping to change at page 16, line 26
adsl2LConfProfMinSnrmDs adsl2LConfProfMinSnrmDs
adsl2LConfProfMinSnrmUs adsl2LConfProfMinSnrmUs
adsl2LConfProfMsgMinUs adsl2LConfProfMsgMinUs
adsl2LConfProfMsgMinDs adsl2LConfProfMsgMinDs
adsl2LConfProfAtuTransSysEna adsl2LConfProfAtuTransSysEna
adsl2LConfProfPmMode adsl2LConfProfPmMode
adsl2LConfProfL0Time adsl2LConfProfL0Time
adsl2LConfProfL2Time adsl2LConfProfL2Time
adsl2LConfProfL2Atpr adsl2LConfProfL2Atpr
adsl2LConfProfL2Atprt adsl2LConfProfL2Atprt
adsl2LconfProfRowStatus adsl2LConfProfRowStatus
adsl2LconfProfAdslMode adsl2LConfProfAdslMode
adsl2LConfProfMaxNomPsdDs adsl2LConfProfMaxNomPsdDs
adsl2LConfProfMaxNomPsdUs adsl2LConfProfMaxNomPsdUs
adsl2LConfProfMaxNomAtpDs adsl2LConfProfMaxNomAtpDs
adsl2LConfProfMaxNomAtpUs adsl2LConfProfMaxNomAtpUs
adsl2LConfProfMaxAggRxPwrUs adsl2LConfProfMaxAggRxPwrUs
adsl2LConfProfPsdMaskDs adsl2LConfProfPsdMaskDs
adsl2LConfProfPsdMaskUs adsl2LConfProfPsdMaskUs
adsl2LConfProfPsdMaskSelectUs adsl2LConfProfPsdMaskSelectUs
adsl2LConfProfModeSpecRowStatus adsl2LConfProfModeSpecRowStatus
adsl2ChConfProfProfileName adsl2ChConfProfProfileName
skipping to change at page 17, line 46 skipping to change at page 17, line 43
adsl2ChAlarmConfProfileAturThresh15MinCodingViolations adsl2ChAlarmConfProfileAturThresh15MinCodingViolations
adsl2ChAlarmConfProfileAturThresh15MinCorrected adsl2ChAlarmConfProfileAturThresh15MinCorrected
adsl2ChAlarmConfProfileRowStatus adsl2ChAlarmConfProfileRowStatus
Note also that the interface indices in this MIB are maintained Note also that the interface indices in this MIB are maintained
persistently. View-based Access Control Model (VACM) data relating persistently. View-based Access Control Model (VACM) data relating
to these SHOULD be stored persistently as well [RFC3410]. to these SHOULD be stored persistently as well [RFC3410].
2.6. Line Topology 2.6. Line Topology
An ADSL/ADSL2 and ADSL2+ Line consists of two units: atuc (the An ADSL/ADSL2 and ADSL2+ Line consists of two units: ATU-C (the
central termination unit) and atur (the remote termination unit). central office termination unit) and ATU-R (the remote termination
There are up to 4 channels, each carrying an independent information unit). There are up to 4 channels, each carrying an independent
flow, as shown in the figure below. information flow, as shown in the figure below.
<-- Network Side Customer Side --> <-- Network Side Customer Side -->
|<//////////////// ADSL/ADSL2/ADSL2+ Span /////////////////>| |<//////////////// ADSL/ADSL2/ADSL2+ Span /////////////////>|
+-------+ +-------+ +-------+ +-------+
+ |<---------------------1------------------->| + + |<---------------------1------------------->| +
+ |<---------------------2------------------->| + + |<---------------------2------------------->| +
| atuc <~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~>| atur | | ATU-C <~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~>| ATU-R |
+ |<---------------------3------------------->| + + |<---------------------3------------------->| +
+ |<---------------------4------------------->| + + |<---------------------4------------------->| +
+-------+ +-------+ +-------+ +-------+
Key: <////> ADSL/ADSL2/ADSL2+ Span Key: <////> ADSL/ADSL2/ADSL2+ Span
<~~~~> ADSL/ADSL2/ADSL2+ twisted-pair <~~~~> ADSL/ADSL2/ADSL2+ twisted-pair
-1- Channel #1 carried over the line -1- Channel #1 carried over the line
-2- Optional channel #2 carried over the line -2- Optional channel #2 carried over the line
-3- Optional channel #3 carried over the line -3- Optional channel #3 carried over the line
-4- Optional channel #4 carried over the line -4- Optional channel #4 carried over the line
Figure 2: General topology for an ADSL/ADSL2/ADSL2+ Line Figure 2: General topology for an ADSL/ADSL2/ADSL2+ Line
2.7. Counters, Interval Buckets, and Thresholds 2.7. Counters, Interval Buckets, and Thresholds
2.7.1. Counters Managed 2.7.1. Counters Managed
There are various types of counters specified in this MIB. Each There are various types of counters specified in this MIB. Each
counter refers either to the whole ADSL/ADSL2/ADSL2+ line, to one of counter refers either to the whole ADSL/ADSL2/ADSL2+ line, to one of
the xtu entities, or to one of the bearer channels. the XTU entities, or to one of the bearer channels.
o On the whole line level o On the whole line level
For full initializations, failed full initializations, short For full initializations, failed full initializations, short
initializations, and for failed short initializations there are event initializations, and failed short initializations, there are event
counters, current 15-minute and 0 to 96 15-minute history bucket(s) counters, current 15-minute and 0 to 96 15-minute history bucket(s)
of "interval-counters", as well as current and 0 to 30 previous 1-day of "interval-counters", as well as current and 0 to 30 previous 1-day
interval-counter(s). Each current 15-minute "failed" event bucket interval-counter(s). Each current 15-minute "failed" event bucket
has an associated threshold notification. has an associated threshold notification.
o On the xtu level o On the XTU level
For the LOS Seconds, ES, SES, FEC seconds, and UAS, there are event For the LOS Seconds, ES, SES, FEC seconds, and UAS, there are event
counters, current 15-minute and 0 to 96 15-minute history bucket(s) counters, current 15-minute and 0 to 96 15-minute history bucket(s)
of "interval-counters", as well as current and 0 to 30 previous 1-day of "interval-counters", as well as current and 0 to 30 previous 1-day
interval-counter(s). Each current 15-minute event bucket has an interval-counter(s). Each current 15-minute event bucket has an
associated threshold notification. associated threshold notification.
o On the bearer channel level o On the bearer channel level
For the coding violations (CRC anomalies) and corrected blocks (i.e., For the coding violations (CRC anomalies) and corrected blocks (i.e.,
FEC events) there are event counters, current 15-minute and 0 to 96 FEC events), there are event counters, current 15-minute and 0 to 96
15-minute history bucket(s) of "interval-counters", as well as 15-minute history bucket(s) of "interval-counters", as well as
current and 0 to 30 previous 1-day interval-counter(s). Each current current and 0 to 30 previous 1-day interval-counter(s). Each current
15-minute event bucket has an associated threshold notification. 15-minute event bucket has an associated threshold notification.
2.7.2. Minimum Number Of Buckets 2.7.2. Minimum Number of Buckets
Although it is possible to support up to 96 15-minute history buckets Although it is possible to support up to 96 15-minute history buckets
of "interval-counters", systems implementing this MIB module SHOULD of "interval-counters", systems implementing this MIB module SHOULD
practically support at least 16 buckets, as specified in ITU-T practically support at least 16 buckets, as specified in ITU-T
G.997.1, paragraph 7.2.7.2. G.997.1, paragraph 7.2.7.2.
Similarly, it is possible to support up to 30 previous 1-day Similarly, it is possible to support up to 30 previous 1-day
"interval-counters", but systems implementing this MIB module SHOULD "interval-counters", but systems implementing this MIB module SHOULD
support at least 1 previous day buckets. support at least 1 previous-day bucket.
2.7.3. Interval Buckets Initialization 2.7.3. Interval Buckets Initialization
There is no requirement for an agent to ensure a fixed relationship There is no requirement for an agent to ensure a fixed relationship
between the start of a 15-minute interval and any wall clock; between the start of a 15-minute interval and any wall clock;
however, some implementations may align the 15-minute intervals with however, some implementations may align the 15-minute intervals with
quarter hours. Likewise, an implementation may choose to align one quarter hours. Likewise, an implementation may choose to align one
day intervals with the start of a day. day intervals with the start of a day.
Counters are not reset when an xtU is reinitialized, only when the Counters are not reset when an XTU is reinitialized, only when the
agent is reset or reinitialized (or under specific request outside agent is reset or reinitialized (or under specific request outside
the scope of this MIB module). the scope of this MIB module).
2.7.4. Interval Buckets Validity 2.7.4. Interval Buckets Validity
As in RFC 3593 [RFC3593] and RFC 2662 [RFC2662], in case the data for As in RFC 3593 [RFC3593] and RFC 2662 [RFC2662], in case the data for
an interval is suspect or known to be invalid, the agent MUST report an interval is suspect or known to be invalid, the agent MUST report
the interval as invalid. If the current 15-minute event bucket is the interval as invalid. If the current 15-minute event bucket is
determined to be invalid, the element management system SHOULD ignore determined to be invalid, the element management system SHOULD ignore
its content and the agent MUST NOT generate notifications based upon its content, and the agent MUST NOT generate notifications based upon
the value of the event bucket. the value of the event bucket.
A valid 15-minute event bucket SHOULD usually count the events for A valid 15-minute event bucket SHOULD usually count the events for
exactly 15 minutes. Similarly, a valid 1-day event bucket SHOULD exactly 15 minutes. Similarly, a valid 1-day event bucket SHOULD
usually count the events for exactly 24 hours. However, the usually count the events for exactly 24 hours. However, the
following scenarios are exceptional: following scenarios are exceptional:
1) For implementations that align the 15-minute intervals with 1) For implementations that align the 15-minute intervals with
quarter hours, and the 1-day intervals with start of a day, the quarter hours, and the 1-day intervals with start of a day, the
management system may still start the PM process not aligned with management system may still start the PM process not aligned with
skipping to change at page 20, line 11 skipping to change at page 20, line 11
exactly 15 minutes. Similarly, a valid 1-day event bucket SHOULD exactly 15 minutes. Similarly, a valid 1-day event bucket SHOULD
usually count the events for exactly 24 hours. However, the usually count the events for exactly 24 hours. However, the
following scenarios are exceptional: following scenarios are exceptional:
1) For implementations that align the 15-minute intervals with 1) For implementations that align the 15-minute intervals with
quarter hours, and the 1-day intervals with start of a day, the quarter hours, and the 1-day intervals with start of a day, the
management system may still start the PM process not aligned with management system may still start the PM process not aligned with
the wall clock. Such a management system may wish to retrieve the wall clock. Such a management system may wish to retrieve
even partial information for the first event buckets, rather than even partial information for the first event buckets, rather than
declaring them all as invalid. declaring them all as invalid.
2) For an event bucket that suffered relatively short outages, the 2) For an event bucket that suffered relatively short outages, the
management system may wish to retrieve the available PM outcomes, management system may wish to retrieve the available PM outcomes,
rather than declaring the whole event bucket as invalid. This is rather than declare the whole event bucket as invalid. This is
more important for 1-day event buckets. more important for 1-day event buckets.
3) An event bucket may be shorter or longer than the formal duration 3) An event bucket may be shorter or longer than the formal duration
if a clock adjustment was performed during the interval. if a clock adjustment was performed during the interval.
This MIB allows supporting the exceptional scenarios described above This MIB allows supporting the exceptional scenarios described above
by reporting the actual Monitoring Time of a monitoring interval. by reporting the actual Monitoring Time of a monitoring interval.
This parameter is relevant only for Valid intervals, but is useful This parameter is relevant only for Valid intervals, but is useful
for these exceptional scenarios: for these exceptional scenarios:
a) The management system MAY still declare a partial PM interval as a) The management system MAY still declare a partial PM interval as
Valid and report the actual number of seconds the interval lasted. Valid and report the actual number of seconds the interval lasted.
b) If the interval was shortened or extended due to clock b) If the interval was shortened or extended due to clock
corrections, the management system SHOULD report the actual number corrections, the management system SHOULD report the actual number
of seconds the interval lasted, beside reporting that the interval of seconds the interval lasted, besides reporting that the
is Valid. interval is Valid.
2.8. Profiles 2.8. Profiles
As a managed node can handle a large number of xtUs, (e.g., hundreds As a managed node can handle a large number of XTUs, (e.g., hundreds
or perhaps thousands of lines), provisioning every parameter on every or perhaps thousands of lines), provisioning every parameter on every
xtU may become burdensome. Moreover, most lines are provisioned XTU may become burdensome. Moreover, most lines are provisioned
identically with the same set of parameters. To simplify the identically with the same set of parameters. To simplify the
provisioning process, this MIB module makes use of profiles and provisioning process, this MIB module makes use of profiles and
templates. templates.
A configuration profile is a set of parameters that can be shared by A configuration profile is a set of parameters that can be shared by
multiple entities. There are configuration profiles to address the multiple entities. There are configuration profiles to address the
line level provisioning and another type of profile that addresses line-level provisioning, and another type of profile that addresses
the channel level provisioning parameters. the channel-level provisioning parameters.
A configuration template is actually a profile-of-profiles. That is, A configuration template is actually a profile-of-profiles. That is,
a template is comprised of one line configuration profile and one or a template is comprised of one line configuration profile and one or
more channel configuration profiles. A template provides the more channel configuration profiles. A template provides the
complete configuration of a line. The same configuration can be complete configuration of a line. The same configuration can be
shared by multiple lines. shared by multiple lines.
Similarly to the configuration profiles and templates, this MIB Similarly to the configuration profiles and templates, this MIB
module makes use of templates and profiles for specifying the alarm module makes use of templates and profiles for specifying the alarm
thresholds associated with performance parameters. This allows thresholds associated with performance parameters. This allows
provisioning multiple lines with the same criteria for generating provisioning multiple lines with the same criteria for generating
threshold crossing notifications. threshold crossing notifications.
The following paragraphs describe templates and profiles used in this The following paragraphs describe templates and profiles used in this
MIB module MIB module
2.8.1. Configuration Profiles And Templates 2.8.1. Configuration Profiles and Templates
o Line Configuration Profiles - Line configuration profiles contain o Line Configuration Profiles - Line configuration profiles contain
parameters for configuring the low layer of ADSL/ADSL2 and ADSL2+ parameters for configuring the low layer of ADSL/ADSL2 and ADSL2+
lines. They are defined in the adsl2LineConfProfTable. lines. They are defined in the adsl2LineConfProfTable.
The line configuration includes issues such as the specific ADSL/ The line configuration includes issues such as the specific
ADSL2 or ADSL2+ modes to enable on the respective line, power ADSL/ADSL2 or ADSL2+ modes to enable on the respective line, power
spectrum parameters, rate adaptation criteria, and SNR margin spectrum parameters, rate adaptation criteria, and SNR margin-
related parameters. A subset of the line configuration parameters related parameters. A subset of the line configuration parameters
depends upon the specific ADSL Mode allowed (i.e., Does the depends upon the specific ADSL Mode allowed (i.e., Does the
profile allow ADSL, ADSL2 and/or ADSL2+?) as well as what annex/ profile allow ADSL, ADSL2, and/or ADSL2+) as well as what
annexes of the standard are allowed. This is the reason a line annex/annexes of the standard are allowed. This is the reason a
profile MUST include one or more mode-specific extensions. line profile MUST include one or more mode-specific extensions.
o Channel Configuration Profiles - Channel configuration profiles o Channel Configuration Profiles - Channel configuration profiles
contain parameters for configuring bearer channels over the ADSL/ contain parameters for configuring bearer channels over the
ADSL2 and ADSL2+ lines. They are sometimes considered as the ADSL/ADSL2 and ADSL2+ lines. They are sometimes considered the
service layer configuration of the ADSL/ADSL2 and ADSL2+ lines. service layer configuration of the ADSL/ADSL2 and ADSL2+ lines.
They are defined in the adsl2ChConfProfTable. They are defined in the adsl2ChConfProfTable.
The channel configuration includes issues such as the desired The channel configuration includes issues such as the desired
minimum and maximum rate on each traffic flow direction and minimum and maximum rate on each traffic flow direction and
impulse noise protection parameters. impulse noise protection parameters.
o Line Configuration Templates - Line configuration templates allow o Line Configuration Templates - Line configuration templates allow
combining line configuration profiles and channel configuration combining line configuration profiles and channel configuration
profiles to a comprehensive configuration of the ADSL/ADSL2 and profiles to a comprehensive configuration of the ADSL/ADSL2 and
ADSL2+ line. They are defined in the adsl2LineConfTemplateTable. ADSL2+ line. They are defined in the adsl2LineConfTemplateTable.
The line configuration template includes one index (OID) of a line The line configuration template includes one index (OID) of a line
configuration profile and one to four indexes of channel configuration profile and one to four indexes of channel
configuration profiles. The template also addresses the issue of configuration profiles. The template also addresses the issue of
distributing the excess available data rate on each traffic flow distributing the excess available data rate on each traffic flow
direction (i.e., the data rate left after each channel is direction (i.e., the data rate left after each channel is
allocated a data rate to satisfy its minimum requested data rate) allocated a data rate to satisfy its minimum requested data rate)
among the various channels. among the various channels.
2.8.2. Alarm Configuration Profiles And Templates 2.8.2. Alarm Configuration Profiles and Templates
o Line Alarm Configuration Profiles - Line level Alarm configuration
o Line Alarm Configuration Profiles - Line-level Alarm configuration
profiles contain the threshold values for Performance Monitoring profiles contain the threshold values for Performance Monitoring
(PM) parameters, counted either on the whole line level or on an (PM) parameters, counted either on the whole line level or on an
xtu level. Thresholds are required only for failures and XTU level. Thresholds are required only for failures and
anomalies. E.g., there are thresholds for failed initializations anomalies, e.g., there are thresholds for failed initializations
and LOS seconds, but not for the aggregate number of full and LOS seconds, but not for the aggregate number of full
initializations. These profiles are defined in the initializations. These profiles are defined in the
adsl2LineAlarmConfProfTable. adsl2LineAlarmConfProfileTable.
o Channel Alarm Configuration Profiles - Channel level Alarm o Channel Alarm Configuration Profiles - Channel-level Alarm
configuration profiles contain the threshold values for PM configuration profiles contain the threshold values for PM
parameters counted on a bearer channel level. Thresholds are parameters counted on a bearer channel level. Thresholds are
defined for two types of anomalies: corrected blocks and coding defined for two types of anomalies: corrected blocks and coding
violations. These profiles are defined in the violations. These profiles are defined in the
adsl2ChAlarmConfProfTable. adsl2ChAlarmConfProfileTable.
o Line Alarm Configuration Templates - Line Alarm configuration o Line Alarm Configuration Templates - Line Alarm configuration
templates allow combining line level alarm configuration profiles templates allow combining line-level alarm configuration profiles
and channel level alarm configuration profiles to a comprehensive and channel-level alarm configuration profiles to a comprehensive
configuration of the PM thresholds for ADSL/ADSL2 and ADSL2+ line. configuration of the PM thresholds for ADSL/ADSL2 and ADSL2+ line.
They are defined in the adsl2LineAlarmConfTemplateTable. They are defined in the adsl2LineAlarmConfTemplateTable.
The line alarm configuration template includes one index (OID) of The line alarm configuration template includes one index (OID) of
a line level alarm configuration profile and one to four indexes a line-level alarm configuration profile and one to four indexes
of channel level alarm configuration profiles. of channel-level alarm configuration profiles.
2.8.3. Managing Profiles And Templates 2.8.3. Managing Profiles and Templates
The index value for each profile and template is a locally-unique, The index value for each profile and template is a locally-unique,
administratively assigned name having the textual convention administratively assigned name having the textual convention
'SnmpAdminString' (RFC 3411 [RFC3411]). 'SnmpAdminString' (RFC 3411 [RFC3411]).
One or more lines may be configured to share parameters of a single One or more lines may be configured to share parameters of a single
configuration template (e.g., adsl2LConfTempTemplateName = 'silver') configuration template (e.g., adsl2LConfTempTemplateName = 'silver')
by setting its adsl2LCnfgLineTemplate objects to the value of this by setting its adsl2LineCnfgTemplate objects to the value of this
template. template.
One or more lines may be configured to share parameters of a single One or more lines may be configured to share parameters of a single
Alarm configuration template (e.g., adsl2LAlarmConfTempTemplateName = Alarm configuration template (e.g., adsl2LAlarmConfTempTemplateName =
'silver') by setting its adsl2LCnfgAlarmTemplate objects to the value 'silver') by setting its adsl2LineAlarmCnfgTemplate objects to the
of this template. value of this template.
Before a template can be deleted or taken out of service it MUST be Before a template can be deleted or taken out of service, it MUST
first unreferenced from all associated lines. Implementations MAY first be unreferenced from all associated lines. Implementations MAY
also reject template modification while it is associated with any also reject template modification while it is associated with any
line. line.
Before a profile can be deleted or taken out of service it MUST be Before a profile can be deleted or taken out of service, it MUST
first unreferenced from all associated templates. Implementations first be unreferenced from all associated templates. Implementations
MAY also reject profile modification while it is referenced by any MAY also reject profile modification while it is referenced by any
template. template.
Implementations MUST provide a default profile whose name is 'DEFVAL' Implementations MUST provide a default profile whose name is 'DEFVAL'
for each profile and template type. The values of the associated for each profile and template type. The values of the associated
parameters will be vendor-specific unless otherwise indicated in this parameters will be vendor-specific unless otherwise indicated in this
document. Before a line's templates have been set, these templates document. Before a line's templates have been set, these templates
will be automatically used by setting adsl2LCnfgLineTemplate and will be automatically used by setting adsl2LineCnfgTemplate and
adsl2LCnfgAlarmTemplate to 'DEFVAL' where appropriate. This default adsl2LineAlarmCnfgTemplate to 'DEFVAL' where appropriate. This
profile name, 'DEFVAL', is considered reserved in the context of default profile name, 'DEFVAL', is considered reserved in the context
profiles and templates defined in this MIB module. of profiles and templates defined in this MIB module.
Profiles and templates are created, assigned, and deleted dynamically Profiles and templates are created, assigned, and deleted dynamically
using the profile name and profile row status in each of the profile using the profile name and profile row status in each of the profile
tables. tables.
If the implementation allows modifying a profile or template while it If the implementation allows modifying a profile or template while it
is associated with a line, then such changes MUST take effect is associated with a line, then such changes MUST take effect
immediately. These changes MAY result in a restart (hard reset or immediately. These changes MAY result in a restart (hard reset or
soft restart) of the units on the line. soft restart) of the units on the line.
skipping to change at page 23, line 35 skipping to change at page 23, line 40
The number of bearer channels is configured by setting the template The number of bearer channels is configured by setting the template
attributes adsl2LConfTempChan1ConfProfile, attributes adsl2LConfTempChan1ConfProfile,
adsl2LConfTempChan2ConfProfile, adsl2LConfTempChan3ConfProfile, and adsl2LConfTempChan2ConfProfile, adsl2LConfTempChan3ConfProfile, and
adsl2LConfTempChan4ConfProfile and then assigning that template to a adsl2LConfTempChan4ConfProfile and then assigning that template to a
DSL line using the adsl2LineCnfgTemplate attribute. When the number DSL line using the adsl2LineCnfgTemplate attribute. When the number
of bearer channels for a DSL line changes, the SNMP agent will of bearer channels for a DSL line changes, the SNMP agent will
automatically create or destroy rows in channel-related tables automatically create or destroy rows in channel-related tables
associated with that line. For example, when a DSL line is operating associated with that line. For example, when a DSL line is operating
with one bearer channel, there will be zero rows in channel-related with one bearer channel, there will be zero rows in channel-related
tables for channels two, three, and four. The SNMP agent MUST create tables for channels two, three, and four. The SNMP agent MUST create
and destroy channel related rows as follows : and destroy channel-related rows as follows:
o When the number of bearer channels for a DSL line changes to a o When the number of bearer channels for a DSL line changes to a
higher number, the SNMP agent will automatically create rows in higher number, the SNMP agent will automatically create rows in
the adsl2ChannelStatusTable, and adsl2PMChCurrTable tables for the adsl2ChannelStatusTable, and adsl2PMChCurrTable tables for
that line. that line.
o When the number of bearer channels for a DSL line changes to a o When the number of bearer channels for a DSL line changes to a
lower number, the SNMP agent will automatically destroy rows in lower number, the SNMP agent will automatically destroy rows in
the adsl2ChannelStatusTable, the adsl2ChannelStatusTable, adsl2PMChCurrTable,
adsl2PMChCurrTable,adsl2PMChHist15MinTable and adsl2PMChHist15MinTable, and adsl2PMChHist1DTable tables for that
adsl2PMChHist1DTable tables for that line. line.
2.9. Notifications 2.9. Notifications
The ability to generate the SNMP notifications coldStart/warmStart The ability to generate the SNMP notifications coldStart/warmStart
(per [RFC3418]), which are per agent (e.g., per Digital Subscriber (per [RFC3418]), which are per agent (e.g., per Digital Subscriber
Line Access Multiplexer, or DSLAM, in such a device), and linkUp/ Line Access Multiplexer, or DSLAM, in such a device), and
linkDown (per [RFC2863]), which are per interface (i.e., ADSL/ADSL2 linkUp/linkDown (per [RFC2863]), which are per interface (i.e.,
or ADSL2+ line) is REQUIRED. ADSL/ADSL2 or ADSL2+ line), is REQUIRED.
A linkDown notification MAY be generated whenever any of ES, SES, CRC A linkDown notification MAY be generated whenever any of ES, SES, CRC
Anomaly, LOS, LOF, or UAS event occurs. The corresponding linkUp Anomaly, LOS, LOF, or UAS event occurs. The corresponding linkUp
notification MAY be sent when all link failure conditions are notification MAY be sent when all link failure conditions are
cleared. cleared.
The notifications defined in this MIB module are for status change The notifications defined in this MIB module are for status change
(e.g., initialization failure) and for the threshold crossings (e.g., initialization failure) and for the threshold crossings
associated with the following events: Full initialization failures, associated with the following events: full initialization failures,
short initialization failures, ES, SES, FEC Seconds, LOS Seconds, short initialization failures, ES, SES, FEC Seconds, LOS Seconds,
UAS, FEC Seconds, FEC events, and CRC anomalies. Each threshold has UAS, FEC Seconds, FEC events, and CRC anomalies. Each threshold has
its own enable/threshold value. When that value is 0, the its own enable/threshold value. When that value is 0, the
notification is disabled. notification is disabled.
The adsl2LStatusStatusAtur and adsl2LStatusStatusAtuc are bitmasks The adsl2LineStatusAtur and adsl2LineStatusAtuc are bitmasks
representing all outstanding error conditions associated with the representing all outstanding error conditions associated with the
AtuR and AtuC (respectively). Note that since the AtuR status is ATU-R and ATU-C (respectively). Note that since the ATU-R status is
obtained via the EOC, this information may be unavailable in case the obtained via the EOC, this information may be unavailable in case the
AtuR is unreachable via EOC during a line error condition. ATU-R is unreachable via EOC during a line error condition.
Therefore, not all conditions may always be included in its current Therefore, not all conditions may always be included in its current
status. Notifications corresponding to the bit fields in those two status. Notifications corresponding to the bit fields in those two
status objects are defined. status objects are defined.
Note that there are other status parameters that refer to the AtuR Note that there are other status parameters that refer to the ATU-R
(e.g., downstream line attenuation). Those parameters also depend on (e.g., downstream line attenuation). Those parameters also depend on
the availability of EOC between the central office xtu and the remote the availability of EOC between the ATU-C and the ATU-R.
xtu.
A threshold notification occurs whenever the corresponding current A threshold notification occurs whenever the corresponding current
15-minute interval error counter becomes equal to, or exceeds the 15-minute interval error counter becomes equal to or exceeds the
threshold value. Only one notification SHOULD be sent per interval threshold value. Only one notification SHOULD be sent per interval
per interface. Since the current 15-minute counter is reset to 0 per interface. Since the current 15-minute counter is reset to 0
every 15 minutes, and if the condition persists, the notification may every 15 minutes, if the condition persists, the notification may
recur as often as every 15 minutes. For example, to get a recur as often as every 15 minutes. For example, to get a
notification whenever a "loss of" event occurs (but at most once notification whenever a "loss of" event occurs (but at most once
every 15 minutes), set the corresponding threshold to 1. The agent every 15 minutes), set the corresponding threshold to 1. The agent
will generate a notification when the event originally occurs. will generate a notification when the event originally occurs.
Notifications, other than the threshold notifications listed above, Notifications, other than the threshold notifications listed above,
SHOULD be rate limited (throttled) such that there is an SHOULD be rate-limited (throttled) such that there is an
implementation-specific gap between the generation of consecutive implementation-specific gap between the generation of consecutive
notifications of the same event. When notifications are rate notifications of the same event. When notifications are rate-
limited, they are dropped and not queued for sending at a future limited, they are dropped and not queued for sending at a future
time. This is intended to be a general rate-limiting statement for time. This is intended to be a general rate-limiting statement for
notifications that otherwise have no explicit rate limiting notifications that otherwise have no explicit rate-limiting
assertions in this document. assertions in this document.
Note that the Network Management System, or NMS, may receive a Note that the Network Management System, or NMS, may receive a
linkDown notification, as well, if enabled (via linkDown notification, as well, if enabled (via
ifLinkUpDownTrapEnable [RFC2863]). At the beginning of the next 15 ifLinkUpDownTrapEnable [RFC2863]). At the beginning of the next 15
minute interval, the counter is reset. When the first second goes by minute interval, the counter is reset. When the first second goes by
and the event occurs, the current interval bucket will be 1, which and the event occurs, the current interval bucket will be 1, which
equals the threshold, and the notification will be sent again. equals the threshold, and the notification will be sent again.
3. Definitions 3. Definitions
skipping to change at page 25, line 25 skipping to change at page 25, line 29
IMPORTS IMPORTS
MODULE-IDENTITY, MODULE-IDENTITY,
transmission transmission
FROM SNMPv2-SMI FROM SNMPv2-SMI
TEXTUAL-CONVENTION TEXTUAL-CONVENTION
FROM SNMPv2-TC; FROM SNMPv2-TC;
adsl2TCMIB MODULE-IDENTITY adsl2TCMIB MODULE-IDENTITY
LAST-UPDATED "200606110000Z" -- June 11, 2006 LAST-UPDATED "200610040000Z" -- October 4th, 2006
ORGANIZATION "ADSLMIB Working Group" ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO "WG-email: adslmib@ietf.org CONTACT-INFO "WG-email: adslmib@ietf.org
Info: https://www1.ietf.org/mailman/listinfo/adslmib Info: https://www1.ietf.org/mailman/listinfo/adslmib
Chair: Mike Sneed Chair: Mike Sneed
Sand Channel Systems Sand Channel Systems
Postal: P.O. Box 37324 Postal: P.O. Box 37324
Raleigh NC 27627-732 Raleigh NC 27627-732
Email: sneedmike@hotmail.com Email: sneedmike@hotmail.com
Phone: +1 206 600 7022 Phone: +1 206 600 7022
skipping to change at page 26, line 30 skipping to change at page 26, line 31
NEC Australia NEC Australia
Postal: 649-655 Springvale Road, Postal: 649-655 Springvale Road,
Mulgrave, Victoria 3170, Mulgrave, Victoria 3170,
Australia. Australia.
Email: umberto.bonollo@nec.com.au Email: umberto.bonollo@nec.com.au
Phone: +61 3 9264 3385 Phone: +61 3 9264 3385
" "
DESCRIPTION DESCRIPTION
"This MIB Module provides Textual Conventions to be "This MIB Module provides Textual Conventions to be
used by the ADSL2-LINE-MIB module for the purpose of used by the ADSL2-LINE-MIB module for the purpose of
managing ADSL, ADSL2 and ADSL2+ lines. managing ADSL, ADSL2, and ADSL2+ lines.
Copyright (C) The Internet Society (2006). This version of Copyright (C) The Internet Society (2006). This version of
this MIB module is part of RFC XXXX: see the RFC itself for this MIB module is part of RFC 4706: see the RFC itself for
full legal notices." full legal notices."
-- RFC Ed.: replace XXXX with assigned number & remove this note REVISION "200610040000Z" -- October 4th, 2006
REVISION "200606110000Z" -- June 11, 2006 DESCRIPTION "Initial version, published as RFC 4706."
DESCRIPTION "Initial version, published as RFC XXXX." ::= { transmission 238 2 } -- adsl2MIB 2
-- RFC Ed.: replace XX with assigned number & remove this note
::= { transmission xxx 2} -- adsl2MIB 2
-- IANA, the xxx here must be the same as the one assigned
-- to the adsl2MIB below.
-- RFC Ed.: Please fill in xxx once assigned by IANA.
------------------------------------------------ ------------------------------------------------
-- Textual Conventions -- -- Textual Conventions --
------------------------------------------------ ------------------------------------------------
Adsl2Unit ::= TEXTUAL-CONVENTION Adsl2Unit ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Identifies a transceiver as being either atuc or "Identifies a transceiver as being either an ATU-C or
atur. An ADSL line consists of two transceivers, an atuc an ATU-R. An ADSL line consists of two transceivers, an ATU-C
and an atur. Attributes with this syntax reference the two and an ATU-R. Attributes with this syntax reference the two
sides of a line. Specified as an INTEGER, the two values sides of a line. Specified as an INTEGER, the two values
are: are:
atuc(1) -- central site transceiver
atur(2) -- remote site transceiver" atuc(1) -- Central office ADSL terminal unit (ATU-C).
atur(2) -- Remote ADSL terminal unit (ATU-R)."
SYNTAX INTEGER { SYNTAX INTEGER {
atuc(1), atuc(1),
atur(2) atur(2)
} }
Adsl2Direction ::= TEXTUAL-CONVENTION Adsl2Direction ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Identifies the direction of a band as being "Identifies the direction of a band as being
either upstream or downstream. Specified as an INTEGER, either upstream or downstream. Specified as an INTEGER,
the two values are: the two values are:
upstream(1) upstream(1), and
downstream(2)" downstream(2)."
SYNTAX INTEGER { SYNTAX INTEGER {
upstream(1), upstream(1),
downstream(2) downstream(2)
} }
Adsl2TransmissionModeType ::= TEXTUAL-CONVENTION Adsl2TransmissionModeType ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A set of ADSL2 line transmission modes, with one bit "A set of ADSL2 line transmission modes, with one bit
per mode. The notes (F) and (L) denote Full-Rate per mode. The notes (F) and (L) denote Full-Rate
and Lite/splitterless respectively: and Lite/splitterless, respectively:
Bit 00 : Regional Std. (ANSI T1.413) (F) Bit 00 : Regional Std. (ANSI T1.413) (F)
Bit 01 : Regional Std. (ETSI DTS/TM06006) (F) Bit 01 : Regional Std. (ETSI DTS/TM06006) (F)
Bit 02 : G.992.1 POTS non-overlapped (F) Bit 02 : G.992.1 POTS non-overlapped (F)
Bit 03 : G.992.1 POTS overlapped (F) Bit 03 : G.992.1 POTS overlapped (F)
Bit 04 : G.992.1 ISDN non-overlapped (F) Bit 04 : G.992.1 ISDN non-overlapped (F)
Bit 05 : G.992.1 ISDN overlapped (F) Bit 05 : G.992.1 ISDN overlapped (F)
Bit 06 : G.992.1 TCM-ISDN non-overlapped (F) Bit 06 : G.992.1 TCM-ISDN non-overlapped (F)
Bit 07 : G.992.1 TCM-ISDN overlapped (F) Bit 07 : G.992.1 TCM-ISDN overlapped (F)
Bit 08 : G.992.2 POTS non-overlapped (L) Bit 08 : G.992.2 POTS non-overlapped (L)
Bit 09 : G.992.2 POTS overlapped (L) Bit 09 : G.992.2 POTS overlapped (L)
Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L) Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L)
Bit 11 : G.992.2 with TCM-ISDN overlapped (L) Bit 11 : G.992.2 with TCM-ISDN overlapped (L)
Bit 12 : G.992.1 TCM-ISDN symmetric (F) --- not in G.997.1 Bit 12 : G.992.1 TCM-ISDN symmetric (F) -- not in G.997.1
Bit 13-17: Reserved Bit 13-17: Reserved
Bit 18 : G.992.3 POTS non-overlapped (F) Bit 18 : G.992.3 POTS non-overlapped (F)
Bit 19 : G.992.3 POTS overlapped (F) Bit 19 : G.992.3 POTS overlapped (F)
Bit 20 : G.992.3 ISDN non-overlapped (F) Bit 20 : G.992.3 ISDN non-overlapped (F)
Bit 21 : G.992.3 ISDN overlapped (F) Bit 21 : G.992.3 ISDN overlapped (F)
Bit 22-23: Reserved Bit 22-23: Reserved
Bit 24 : G.992.4 POTS non-overlapped (L) Bit 24 : G.992.4 POTS non-overlapped (L)
Bit 25 : G.992.4 POTS overlapped (L) Bit 25 : G.992.4 POTS overlapped (L)
Bit 26-27: Reserved Bit 26-27: Reserved
Bit 28 : G.992.3 Annex I All-Digital non-overlapped (F) Bit 28 : G.992.3 Annex I All-Digital non-overlapped (F)
skipping to change at page 28, line 47 skipping to change at page 28, line 45
Bit 52-55: Reserved" Bit 52-55: Reserved"
SYNTAX BITS { SYNTAX BITS {
ansit1413(0), ansit1413(0),
etsi(1), etsi(1),
g9921PotsNonOverlapped(2), g9921PotsNonOverlapped(2),
g9921PotsOverlapped(3), g9921PotsOverlapped(3),
g9921IsdnNonOverlapped(4), g9921IsdnNonOverlapped(4),
g9921isdnOverlapped(5), g9921isdnOverlapped(5),
g9921tcmIsdnNonOverlapped(6), g9921tcmIsdnNonOverlapped(6),
g9921tcmIsdnOverlapped(7), g9921tcmIsdnOverlapped(7),
g9922potsNonOverlapeed(8), g9922potsNonOverlapped(8),
g9922potsOverlapped(9), g9922potsOverlapped(9),
g9922tcmIsdnNonOverlapped(10), g9922tcmIsdnNonOverlapped(10),
g9922tcmIsdnOverlapped(11), g9922tcmIsdnOverlapped(11),
g9921tcmIsdnSymmetric(12), g9921tcmIsdnSymmetric(12),
reserved1(13), reserved1(13),
reserved2(14), reserved2(14),
reserved3(15), reserved3(15),
reserved4(16), reserved4(16),
reserved5(17), reserved5(17),
g9923PotsNonOverlapped(18), g9923PotsNonOverlapped(18),
g9923PotsOverlapped(19), g9923PotsOverlapped(19),
g9923IsdnNonOverlapped(20), g9923IsdnNonOverlapped(20),
g9923isdnOverlapped(21), g9923isdnOverlapped(21),
reserved6(22), reserved6(22),
reserved7(23), reserved7(23),
g9924potsNonOverlapeed(24), g9924potsNonOverlapped(24),
g9924potsOverlapped(25), g9924potsOverlapped(25),
reserved8(26), reserved8(26),
reserved9(27), reserved9(27),
g9923AnnexIAllDigNonOverlapped(28), g9923AnnexIAllDigNonOverlapped(28),
g9923AnnexIAllDigOverlapped(29), g9923AnnexIAllDigOverlapped(29),
g9923AnnexJAllDigNonOverlapped(30), g9923AnnexJAllDigNonOverlapped(30),
g9923AnnexJAllDigOverlapped(31), g9923AnnexJAllDigOverlapped(31),
g9924AnnexIAllDigNonOverlapped(32), g9924AnnexIAllDigNonOverlapped(32),
g9924AnnexIAllDigOverlapped(33), g9924AnnexIAllDigOverlapped(33),
g9923AnnexLMode1NonOverlapped(34), g9923AnnexLMode1NonOverlapped(34),
skipping to change at page 30, line 6 skipping to change at page 30, line 4
reserved13(53), reserved13(53),
reserved14(54), reserved14(54),
reserved15(55) reserved15(55)
} }
Adsl2RaMode ::= TEXTUAL-CONVENTION Adsl2RaMode ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Specifies the rate adaptation behavior for the line. "Specifies the rate adaptation behavior for the line.
The three possible behaviors are: The three possible behaviors are:
manual (1) - No Rate-Adaptation. The initialization manual (1) - No Rate-Adaptation. The initialization
process attempts to synchronize to a process attempts to synchronize to a
specified rate. specified rate.
raInit (2) - Rate-Adaptation during initialization process raInit (2) - Rate-Adaptation during initialization process
only, which attempts to synchronize to a rate only, which attempts to synchronize to a rate
between minimum and maximum specified values. between minimum and maximum specified values.
dynamicRa (3)- Dynamic Rate-Adaptation during initialization dynamicRa (3)- Dynamic Rate-Adaptation during initialization
process as well as during SHOWTIME" process as well as during SHOWTIME."
SYNTAX INTEGER { SYNTAX INTEGER {
manual(1), manual(1),
raInit(2), raInit(2),
dynamicRa(3) dynamicRa(3)
} }
Adsl2InitResult ::= TEXTUAL-CONVENTION Adsl2InitResult ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Specifies the result of full initialization attempt; the "Specifies the result of a full initialization attempt; the
six possible result values are: six possible result values are:
noFail (0) - Successful initialization noFail(0) - Successful initialization.
configError (1) - Configuration failure configError(1) - Configuration failure.
configNotFeasible (2) - Configuration details not supported configNotFeasible(2) - Configuration details not supported.
commFail (3) - Communication failure commFail(3) - Communication failure.
noPeerAtu (4) - Peer ATU not detected noPeerAtu(4) - Peer ATU not detected.
otherCause (5) - Other initialization failure reason otherCause(5) - Other initialization failure reason.
The values used are as defined in ITU-T G.997.1, The values used are as defined in ITU-T G.997.1,
paragraph 7.5.1.3" paragraph 7.5.1.3"
SYNTAX INTEGER { SYNTAX INTEGER {
noFail(0), noFail(0),
configError(1), configError(1),
configNotFeasible(2), configNotFeasible(2),
commFail(3), commFail(3),
noPeerAtu(4), noPeerAtu(4),
otherCause(5) otherCause(5)
} }
Adsl2OperationModes ::= TEXTUAL-CONVENTION Adsl2OperationModes ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The ADSL2 management model specified includes an ADSL Mode "The ADSL2 management model specified includes an ADSL Mode
attribute which identifies an instance of ADSL Mode-Specific attribute that identifies an instance of ADSL Mode-Specific
PSD Configuration object in the ADSL Line Profile. The PSD Configuration object in the ADSL Line Profile. The
following classes of ADSL operating mode are defined. following classes of ADSL operating mode are defined.
The notes (F) and (L) denote Full-Rate and Lite/splitterless The notes (F) and (L) denote Full-Rate and Lite/splitterless
respectively: respectively:
+-------+--------------------------------------------------+ +-------+--------------------------------------------------+
| Value | ADSL operation mode description | | Value | ADSL operation mode description |
+-------+--------------------------------------------------+ +-------+--------------------------------------------------+
1 - The default/generic PSD configuration. Default 1 - The default/generic PSD configuration. Default
configuration will be used when no other matching configuration will be used when no other matching
mode specific configuration can be found. mode-specific configuration can be found.
2 - ADSL family. The attributes included in the Mode- 2 - ADSL family. The attributes included in the Mode-
Specific PSD Configuration are irrelevant for Specific PSD Configuration are irrelevant for
ITU-T G.992.1 and G.992.2 ADSL modes. Hence, it ITU-T G.992.1 and G.992.2 ADSL modes. Hence, it
is possible to map those modes to this generic is possible to map those modes to this generic
class. class.
3-7 - Unused. Reserved for future ITU-T specification. 3-7 - Unused. Reserved for future ITU-T specification.
8 - G.992.3 POTS non-overlapped (F) 8 - G.992.3 POTS non-overlapped (F)
9 - G.992.3 POTS overlapped (F) 9 - G.992.3 POTS overlapped (F)
10 - G.992.3 ISDN non-overlapped (F) 10 - G.992.3 ISDN non-overlapped (F)
11 - G.992.3 ISDN overlapped (F) 11 - G.992.3 ISDN overlapped (F)
skipping to change at page 32, line 12 skipping to change at page 32, line 12
40 - G.992.5 Annex M POTS non-overlapped (F) 40 - G.992.5 Annex M POTS non-overlapped (F)
41 - G.992.5 Annex M POTS overlapped (F) 41 - G.992.5 Annex M POTS overlapped (F)
" "
SYNTAX INTEGER { SYNTAX INTEGER {
defMode (1), defMode (1),
adsl(2), adsl(2),
g9923PotsNonOverlapped(8), g9923PotsNonOverlapped(8),
g9923PotsOverlapped(9), g9923PotsOverlapped(9),
g9923IsdnNonOverlapped(10), g9923IsdnNonOverlapped(10),
g9923isdnOverlapped(11), g9923isdnOverlapped(11),
g9924potsNonOverlapeed(14), g9924potsNonOverlapped(14),
g9924potsOverlapped(15), g9924potsOverlapped(15),
g9923AnnexIAllDigNonOverlapped(18), g9923AnnexIAllDigNonOverlapped(18),
g9923AnnexIAllDigOverlapped(19), g9923AnnexIAllDigOverlapped(19),
g9923AnnexJAllDigNonOverlapped(20), g9923AnnexJAllDigNonOverlapped(20),
g9923AnnexJAllDigOverlapped(21), g9923AnnexJAllDigOverlapped(21),
g9924AnnexIAllDigNonOverlapped(22), g9924AnnexIAllDigNonOverlapped(22),
g9924AnnexIAllDigOverlapped(23), g9924AnnexIAllDigOverlapped(23),
g9923AnnexLMode1NonOverlapped(24), g9923AnnexLMode1NonOverlapped(24),
g9923AnnexLMode2NonOverlapped(25), g9923AnnexLMode2NonOverlapped(25),
g9923AnnexLMode3Overlapped(26), g9923AnnexLMode3Overlapped(26),
skipping to change at page 32, line 44 skipping to change at page 32, line 44
g9925AnnexMPotsNonOverlapped(40), g9925AnnexMPotsNonOverlapped(40),
g9925AnnexMPotsOverlapped(41) g9925AnnexMPotsOverlapped(41)
} }
Adsl2PowerMngState ::= TEXTUAL-CONVENTION Adsl2PowerMngState ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Attributes with this syntax uniquely identify each power "Attributes with this syntax uniquely identify each power
management state defined for the ADSL/ADSL2 or ADSL2+ link. management state defined for the ADSL/ADSL2 or ADSL2+ link.
The possible values are: The possible values are:
l0(1) - L0 - Full power management state l0(1) - L0 - Full power management state.
l1(2) - L1 - Low power management state (for G.992.2) l1(2) - L1 - Low power management state (for G.992.2).
l2(3) - L2 - Low power management state (for G.992.3, l2(3) - L2 - Low power management state (for G.992.3,
G.992.4, and G.992.5) G.992.4, and G.992.5).
l3(4) - L3 - Idle power management state" l3(4) - L3 - Idle power management state."
SYNTAX INTEGER { SYNTAX INTEGER {
l0(1), l0(1),
l1(2), l1(2),
l2(3), l2(3),
l3(4) l3(4)
} }
Adsl2ConfPmsForce ::= TEXTUAL-CONVENTION Adsl2ConfPmsForce ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Attributes with this syntax are configuration parameters "Attributes with this syntax are configuration parameters
that reference the desired power management state for the that reference the desired power management state for the
ADSL/ADSL2 or ADSL2+ link: ADSL/ADSL2 or ADSL2+ link:
l3toL0 (0) - Perform a transition from L3 to L0 l3toL0 (0) - Perform a transition from L3 to L0
(Full power management state) (Full power management state).
l0toL2 (2) - Perform a transition from L0 to L2 l0toL2 (2) - Perform a transition from L0 to L2
(Low power management state) (Low power management state).
l0orL2toL3 (3) - Perform a transition into L3 (Idle l0orL2toL3 (3) - Perform a transition into L3 (Idle
power management state) power management state).
The values used are as defined in ITU-T G.997.1, The values used are as defined in ITU-T G.997.1,
paragraph 7.3.1.1.3" paragraph 7.3.1.1.3"
SYNTAX INTEGER { SYNTAX INTEGER {
l3toL0 (0), l3toL0 (0),
l0toL2 (2), l0toL2 (2),
l0orL2toL3 (3) l0orL2toL3 (3)
} }
Adsl2LConfProfPmMode ::= TEXTUAL-CONVENTION Adsl2LConfProfPmMode ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Attributes with this syntax are configuration parameters "Attributes with this syntax are configuration parameters
that reference the power modes/states into which the ATU-C or that reference the power modes/states into which the ATU-C or
ATU-R may autonomously transit. ATU-R may autonomously transit.
It is a BITS structure that allows control of the following It is a BITS structure that allows control of the following
transit options: transit options:
allowTransitionsToIdle (0) - xTU may autonomously transit allowTransitionsToIdle(0) - XTU may autonomously transit
to idle (L3) state. to idle (L3) state.
allowTransitionsToLowPower (1)- xTU may autonomously transit allowTransitionsToLowPower(1) - XTU may autonomously transit
to low-power (L2) state." to low-power (L2) state."
SYNTAX BITS { SYNTAX BITS {
allowTransitionsToIdle(0), allowTransitionsToIdle(0),
allowTransitionsToLowPower(1) allowTransitionsToLowPower(1)
} }
Adsl2LineLdsf ::= TEXTUAL-CONVENTION Adsl2LineLdsf ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Attributes with this syntax are configuration parameters "Attributes with this syntax are configuration parameters
that control the Loop Diagnostic mode for the ADSL/ADSL2 or that control the Loop Diagnostic mode for the ADSL/ADSL2 or
ADSL2+ link. The possible values are: ADSL2+ link. The possible values are:
inhibit (0) - Inhibit Loop Diagnostic mode inhibit(0) - Inhibit Loop Diagnostic mode.
force (1) - Force/Initiate Loop Diagnostic mode force(1) - Force/Initiate Loop Diagnostic mode.
The values used are as defined in ITU-T G.997.1, The values used are as defined in ITU-T G.997.1,
paragraph 7.3.1.1.8" paragraph 7.3.1.1.8"
SYNTAX INTEGER { SYNTAX INTEGER {
inhibit(0), inhibit(0),
force(1) force(1)
} }
Adsl2LdsfResult ::= TEXTUAL-CONVENTION Adsl2LdsfResult ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Possible failure reasons associated with performing "Possible failure reasons associated with performing
Dual Ended Loop Test (DELT) on a DSL line. a Dual Ended Loop Test (DELT) on a DSL line.
Possible values are: Possible values are:
none (1) - The default value in case LDSF was never none (1) - The default value in case LDSF was never
requested for the associated line. requested for the associated line.
success (2) - The recent command completed success (2) - The recent command completed
successfully. successfully.
inProgress (3) - The Loop Diagnostics process is in inProgress (3) - The Loop Diagnostics process is in
progress. progress.
unsupported (4) - The NE or the line card doesn't support unsupported (4) - The NE or the line card doesn't support
LDSF. LDSF.
cannotRun (5) - The NE cannot initiate the command, due cannotRun (5) - The NE cannot initiate the command, due
skipping to change at page 35, line 19 skipping to change at page 35, line 19
illegalMode (8), illegalMode (8),
adminUp (9), adminUp (9),
tableFull (10), tableFull (10),
noResources (11) noResources (11)
} }
Adsl2SymbolProtection ::= TEXTUAL-CONVENTION Adsl2SymbolProtection ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Attributes with this syntax are configuration parameters "Attributes with this syntax are configuration parameters
that reference the minimum length impulse noise protection that reference the minimum-length impulse noise protection
(INP) in terms of number of symbols. The possible values are: (INP) in terms of number of symbols. The possible values are:
noProtection (i.e., INP not required), halfSymbol (i.e., INP noProtection (i.e., INP not required), halfSymbol (i.e., INP
length is 1/2 symbol), and 1-16 symbols in steps of 1 symbol" length is 1/2 symbol), and 1-16 symbols in steps of 1 symbol."
SYNTAX INTEGER { SYNTAX INTEGER {
noProtection (1), noProtection (1),
halfSymbol (2), halfSymbol (2),
singleSymbol (3), singleSymbol (3),
twoSymbols (4), twoSymbols (4),
threeSymbols (5), threeSymbols (5),
fourSymbols (6), fourSymbols (6),
fiveSymbols (7), fiveSymbols (7),
sixSymbols (8), sixSymbols (8),
skipping to change at page 37, line 34 skipping to change at page 37, line 34
associated with the breakpoint. The third octet associated with the breakpoint. The third octet
holds the shaping parameter at the breakpoint. It holds the shaping parameter at the breakpoint. It
is a value from 0 to 127 (units of -0.5dB). The is a value from 0 to 127 (units of -0.5dB). The
special value 127 indicates that the sub-carrier special value 127 indicates that the sub-carrier
is not transmitted." is not transmitted."
SYNTAX OCTET STRING (SIZE(0..96)) SYNTAX OCTET STRING (SIZE(0..96))
Adsl2LastTransmittedState ::= TEXTUAL-CONVENTION Adsl2LastTransmittedState ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This parameter represents the last successful "This parameter represents the last successfully
transmitted initialization state in the last full transmitted initialization state in the last full
initialization performed on the line. States are initialization performed on the line. States are
per the specific xDSL technology and are numbered per the specific xDSL technology and are numbered
from 0 (if G.994.1 is used) or 1 (if G.994.1 is from 0 (if G.994.1 is used) or 1 (if G.994.1 is
not used) up to Showtime." not used) up to Showtime."
SYNTAX INTEGER { SYNTAX INTEGER {
atucG9941(0), atucG9941(0),
atucQuiet1(1), atucQuiet1(1),
atucComb1(2), atucComb1(2),
atucQuiet2(3), atucQuiet2(3),
skipping to change at page 39, line 23 skipping to change at page 39, line 23
Adsl2LineStatus ::= TEXTUAL-CONVENTION Adsl2LineStatus ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Attributes with this syntax are status parameters "Attributes with this syntax are status parameters
that reflect the failure status for a given endpoint of that reflect the failure status for a given endpoint of
ADSL/ADSL2 or ADSL2+ link. ADSL/ADSL2 or ADSL2+ link.
This BITS structure can report the following failures: This BITS structure can report the following failures:
noDefect (0) - This bit position positively reports noDefect (0) - This bit position positively reports
that no defect or failure exist. that no defect or failure exists.
lossOfFraming (1) - Loss of frame synchronization lossOfFrame(1) - Loss of frame synchronization.
lossOfSignal (2) - Loss of signal lossOfSignal(2) - Loss of signal.
lossOfPower (3) - Loss of power. Usually this failure may lossOfPower (3) - Loss of power. Usually this failure may
be reported for CPE units only be reported for ATU-Rs only.
initFailure (4) - Recent initialization process failed. initFailure (4) - Recent initialization process failed.
Never active on ATU-R." Never active on ATU-R."
SYNTAX BITS { SYNTAX BITS {
noDefect(0), noDefect(0),
lossOfFraming(1), lossOfFrame(1),
lossOfSignal(2), lossOfSignal(2),
lossOfPower(3), lossOfPower(3),
initFailure(4) initFailure(4)
} }
Adsl2ChAtmStatus ::= TEXTUAL-CONVENTION Adsl2ChAtmStatus ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Attributes with this syntax are status parameters that "Attributes with this syntax are status parameters that
reflect the failure status for Transmission Convergence (TC) reflect the failure status for Transmission Convergence (TC)
layer of a given ATM interface (data path over an ADSL/ADSL2 layer of a given ATM interface (data path over an ADSL/ADSL2
or ADSL2+ link). or ADSL2+ link).
This BITS structure can report the following failures: This BITS structure can report the following failures:
noDefect (0) - This bit position positively noDefect (0) - This bit position positively
reports that no defect or failure reports that no defect or failure
exist. exists.
noCellDelineation (1) - The link was successfully noCellDelineation (1) - The link was successfully
initialized but cell delineation initialized, but cell delineation
was never acquired on the was never acquired on the
associated ATM data path. associated ATM data path.
lossOfCellDelineation (2)- Loss of cell delineation on the lossOfCellDelineation (2)- Loss of cell delineation on the
associated ATM data path" associated ATM data path."
SYNTAX BITS { SYNTAX BITS {
noDefect(0), noDefect(0),
noCellDelineation(1), noCellDelineation(1),
lossOfCellDelineation(2) lossOfCellDelineation(2)
} }
Adsl2ChPtmStatus ::= TEXTUAL-CONVENTION Adsl2ChPtmStatus ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Attributes with this syntax are status parameters that "Attributes with this syntax are status parameters that
reflect the failure status for a given PTM interface (packet reflect the failure status for a given PTM interface (packet
data path over an ADSL/ADSL2 or ADSL2+ link). data path over an ADSL/ADSL2 or ADSL2+ link).
This BITS structure can report the following failures: This BITS structure can report the following failures:
noDefect (0) - This bit position positively noDefect (0) - This bit position positively
reports that no defect or failure exist. reports that no defect or failure exists.
outOfSync (1) - Out of synchronization. " outOfSync (1) - Out of synchronization. "
SYNTAX BITS { SYNTAX BITS {
noDefect(0), noDefect(0),
outOfSync(1) outOfSync(1)
} }
END END
ADSL2-LINE-MIB DEFINITIONS ::= BEGIN ADSL2-LINE-MIB DEFINITIONS ::= BEGIN
IMPORTS IMPORTS
MODULE-IDENTITY, MODULE-IDENTITY,
OBJECT-TYPE, OBJECT-TYPE,
transmission, transmission,
Unsigned32, Unsigned32,
NOTIFICATION-TYPE, NOTIFICATION-TYPE,
Integer32, Integer32,
Counter32 Counter32
skipping to change at page 41, line 49 skipping to change at page 42, line 13
Adsl2ChAtmStatus, Adsl2ChAtmStatus,
Adsl2ChPtmStatus Adsl2ChPtmStatus
FROM ADSL2-LINE-TC-MIB -- [This document] FROM ADSL2-LINE-TC-MIB -- [This document]
MODULE-COMPLIANCE, MODULE-COMPLIANCE,
OBJECT-GROUP, OBJECT-GROUP,
NOTIFICATION-GROUP NOTIFICATION-GROUP
FROM SNMPv2-CONF; FROM SNMPv2-CONF;
adsl2MIB MODULE-IDENTITY adsl2MIB MODULE-IDENTITY
LAST-UPDATED "200606110000Z" -- June 11, 2006 LAST-UPDATED "200610040000Z" -- October 4th, 2006
ORGANIZATION "ADSLMIB Working Group" ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO "WG-email: adslmib@ietf.org CONTACT-INFO "WG-email: adslmib@ietf.org
Info: https://www1.ietf.org/mailman/listinfo/adslmib Info: https://www1.ietf.org/mailman/listinfo/adslmib
Chair: Mike Sneed Chair: Mike Sneed
Sand Channel Systems Sand Channel Systems
Postal: P.O. Box 37324 Postal: P.O. Box 37324
Raleigh NC 27627-732 Raleigh NC 27627-732
Email: sneedmike@hotmail.com Email: sneedmike@hotmail.com
Phone: +1 206 600 7022 Phone: +1 206 600 7022
skipping to change at page 43, line 27 skipping to change at page 43, line 39
G.992.4, and G.992.5 ([G.992.3], [G.992.4], and [G.992.5], G.992.4, and G.992.5 ([G.992.3], [G.992.4], and [G.992.5],
respectively). In addition, objects have been added to respectively). In addition, objects have been added to
improve the management of ADSL, ADSL2, and ADSL2+ lines. improve the management of ADSL, ADSL2, and ADSL2+ lines.
Additionally, the management framework for New Generation Additionally, the management framework for New Generation
ADSL lines specified by the Digital Subscriber Line Forum ADSL lines specified by the Digital Subscriber Line Forum
(DSLF) has been taken into consideration [TR-90]. That (DSLF) has been taken into consideration [TR-90]. That
framework is based on ITU-T G.997.1 standard [G.997.1] as framework is based on ITU-T G.997.1 standard [G.997.1] as
well as two amendments: [G.997.1 am1] and [G.997.1 am2]. well as two amendments: [G.997.1 am1] and [G.997.1 am2].
Note that the revised ITU-T G.997.1 standard refers also to Note that the revised ITU-T G.997.1 standard also refers to
next generation of VDSL technology, known as VDSL2, per ITU-T the next generation of VDSL technology, known as VDSL2, per
G.993.2 [G.993.2]. However, managing VDSL2 lines is ITU-T G.993.2 [G.993.2]. However, managing VDSL2 lines is
currently beyond the scope of this document. currently beyond the scope of this document.
The MIB module is located in the MIB tree under MIB 2 The MIB module is located in the MIB tree under MIB 2
transmission, as discussed in the MIB-2 Integration (RFC 2863 transmission, as discussed in the IANA Considerations section
[RFC2863]) section of this document. of this document.
Copyright (C) The Internet Society (2006). This version of Copyright (C) The Internet Society (2006). This version of
this MIB module is part of RFC XXXX: see the RFC itself for this MIB module is part of RFC 4706: see the RFC itself for
full legal notices." full legal notices."
REVISION "200610040000Z" -- October 4th, 2006
-- RFC Ed.: replace XXXX with assigned number & remove this note DESCRIPTION "Initial version, published as RFC 4706."
REVISION "200606110000Z" -- June 11, 2006 ::= { transmission 238 }
DESCRIPTION "Initial version, published as RFC XXXX."
-- RFC Ed.: replace XXXX with assigned number & remove this note
::= { transmission xxx }
-- IANA, we suggest to put it under { transmission 230 } because
-- this is the first available number.
-- RFC Ed.: Please fill in xxx once assigned by IANA.
adsl2 OBJECT IDENTIFIER ::= { adsl2MIB 1 } adsl2 OBJECT IDENTIFIER ::= { adsl2MIB 1 }
------------------------------------------------ ------------------------------------------------
adsl2Line OBJECT IDENTIFIER ::= { adsl2 1 } adsl2Line OBJECT IDENTIFIER ::= { adsl2 1 }
adsl2Status OBJECT IDENTIFIER ::= { adsl2 2 } adsl2Status OBJECT IDENTIFIER ::= { adsl2 2 }
adsl2Inventory OBJECT IDENTIFIER ::= { adsl2 3 } adsl2Inventory OBJECT IDENTIFIER ::= { adsl2 3 }
adsl2PM OBJECT IDENTIFIER ::= { adsl2 4 } adsl2PM OBJECT IDENTIFIER ::= { adsl2 4 }
adsl2Profile OBJECT IDENTIFIER ::= { adsl2 5 } adsl2Profile OBJECT IDENTIFIER ::= { adsl2 5 }
adsl2Scalar OBJECT IDENTIFIER ::= { adsl2 6 } adsl2Scalar OBJECT IDENTIFIER ::= { adsl2 6 }
adsl2Notifications OBJECT IDENTIFIER ::= { adsl2 0 } adsl2Notifications OBJECT IDENTIFIER ::= { adsl2 0 }
adsl2Conformance OBJECT IDENTIFIER ::= { adsl2 8 } adsl2Conformance OBJECT IDENTIFIER ::= { adsl2 7 }
------------------------------------------------ ------------------------------------------------
adsl2PMLine OBJECT IDENTIFIER ::= { adsl2PM 1 } adsl2PMLine OBJECT IDENTIFIER ::= { adsl2PM 1 }
adsl2PMChannel OBJECT IDENTIFIER ::= { adsl2PM 2 } adsl2PMChannel OBJECT IDENTIFIER ::= { adsl2PM 2 }
------------------------------------------------ ------------------------------------------------
adsl2ProfileLine OBJECT IDENTIFIER ::= { adsl2Profile 1 } adsl2ProfileLine OBJECT IDENTIFIER ::= { adsl2Profile 1 }
adsl2ProfileChannel OBJECT IDENTIFIER ::= { adsl2Profile 2 } adsl2ProfileChannel OBJECT IDENTIFIER ::= { adsl2Profile 2 }
adsl2ProfileAlarmConf OBJECT IDENTIFIER ::= { adsl2Profile 3 } adsl2ProfileAlarmConf OBJECT IDENTIFIER ::= { adsl2Profile 3 }
------------------------------------------------ ------------------------------------------------
adsl2ScalarSC OBJECT IDENTIFIER ::= { adsl2Scalar 1 } adsl2ScalarSC OBJECT IDENTIFIER ::= { adsl2Scalar 1 }
------------------------------------------------ ------------------------------------------------
------------------------------------------------ ------------------------------------------------
-- adsl2LineTable -- -- adsl2LineTable --
------------------------------------------------ ------------------------------------------------
adsl2LineTable OBJECT-TYPE adsl2LineTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineEntry SYNTAX SEQUENCE OF Adsl2LineEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2LineTable contains configuration, "The table adsl2LineTable contains configuration,
command and status parameters of the ADSL2 line. command, and status parameters of the ADSL2 line.
The index of this table is an interface index where the The index of this table is an interface index where the
interface has an ifType of adsl2(230). interface has an ifType of adsl2plus(238).
Several objects in this table MUST be maintained in a Several objects in this table MUST be maintained in a
persistent manner. " persistent manner. "
::= { adsl2Line 1 } ::= { adsl2Line 1 }
adsl2LineEntry OBJECT-TYPE adsl2LineEntry OBJECT-TYPE
SYNTAX Adsl2LineEntry SYNTAX Adsl2LineEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2LineTable contains configuration, "The table adsl2LineTable contains configuration,
commands and status parameters of the ADSL2 line" commands, and status parameters of the ADSL2 line"
INDEX { ifIndex } INDEX { ifIndex }
::= { adsl2LineTable 1 } ::= { adsl2LineTable 1 }
Adsl2LineEntry ::= Adsl2LineEntry ::=
SEQUENCE { SEQUENCE {
adsl2LineCnfgTemplate SnmpAdminString, adsl2LineCnfgTemplate SnmpAdminString,
adsl2LineAlarmCnfgTemplate SnmpAdminString, adsl2LineAlarmCnfgTemplate SnmpAdminString,
adsl2LineCmndConfPmsf Adsl2ConfPmsForce, adsl2LineCmndConfPmsf Adsl2ConfPmsForce,
adsl2LineCmndConfLdsf Adsl2LineLdsf, adsl2LineCmndConfLdsf Adsl2LineLdsf,
adsl2LineCmndConfLdsfFailReason Adsl2LdsfResult, adsl2LineCmndConfLdsfFailReason Adsl2LdsfResult,
skipping to change at page 46, line 22 skipping to change at page 46, line 28
adsl2LineCmndConfPmsf OBJECT-TYPE adsl2LineCmndConfPmsf OBJECT-TYPE
SYNTAX Adsl2ConfPmsForce SYNTAX Adsl2ConfPmsForce
MAX-ACCESS read-write MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Power management state forced. Defines the line states to be "Power management state forced. Defines the line states to be
forced by the near-end ATU on this line. The various possible forced by the near-end ATU on this line. The various possible
values are: values are:
l3toL0 (0), l3toL0 (0),
l0toL2 (2), l0toL2(2), or
l0orL2toL3 (3). l0orL2toL3 (3).
This object MUST be maintained in a persistent manner." This object MUST be maintained in a persistent manner."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.3" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.3"
DEFVAL { l3toL0 } DEFVAL { l3toL0 }
::= { adsl2LineEntry 3 } ::= { adsl2LineEntry 3 }
adsl2LineCmndConfLdsf OBJECT-TYPE adsl2LineCmndConfLdsf OBJECT-TYPE
SYNTAX Adsl2LineLdsf SYNTAX Adsl2LineLdsf
MAX-ACCESS read-write MAX-ACCESS read-write
skipping to change at page 48, line 21 skipping to change at page 48, line 27
REFERENCE "ITU-T G.997.1 (amendment 1), 7.3.1.1.10" REFERENCE "ITU-T G.997.1 (amendment 1), 7.3.1.1.10"
DEFVAL { false } DEFVAL { false }
::= { adsl2LineEntry 6 } ::= { adsl2LineEntry 6 }
adsl2LineStatusAtuTransSys OBJECT-TYPE adsl2LineStatusAtuTransSys OBJECT-TYPE
SYNTAX Adsl2TransmissionModeType SYNTAX Adsl2TransmissionModeType
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The ATU Transmission System (ATS) in use. "The ATU Transmission System (ATS) in use.
It is coded in a bit-map representation with one bit set to It is coded in a bit-map representation with only a single bit
'1' (the selected coding for the ADSL line). This parameter set to '1' (the selected coding for the ADSL line). This
may be derived from the handshaking procedures defined in parameter may be derived from the handshaking procedures
Recommendation G.994.1. A set of ADSL2 line transmission defined in Recommendation G.994.1. A set of ADSL2 line
modes, with one bit per mode. " transmission modes, with one bit per mode."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.1"
::= { adsl2LineEntry 7 } ::= { adsl2LineEntry 7 }
adsl2LineStatusPwrMngState OBJECT-TYPE adsl2LineStatusPwrMngState OBJECT-TYPE
SYNTAX Adsl2PowerMngState SYNTAX Adsl2PowerMngState
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The current power management state. One of four possible "The current power management state. One of four possible
power management states: power management states:
L0 - Synchronized and full transmission (i.e., Showtime), L0 - Synchronized and full transmission (i.e., Showtime).
L1 - Low Power with reduced net data rate (G.992.2 only), L1 - Low Power with reduced net data rate (G.992.2 only).
L2 - Low Power with reduced net data rate (G.992.3 and L2 - Low Power with reduced net data rate (G.992.3 and
G.992.4 only), G.992.4 only).
L3 - No power L3 - No power.
The various possible values are:l0(1), l1(2), l2(3), l3(4)." The various possible values are: l0(1), l1(2), l2(3), or
l3(4)."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.2" REFERENCE "ITU-T G.997.1, paragraph 7.5.1.2"
::= { adsl2LineEntry 8 } ::= { adsl2LineEntry 8 }
adsl2LineStatusInitResult OBJECT-TYPE adsl2LineStatusInitResult OBJECT-TYPE
SYNTAX Adsl2InitResult SYNTAX Adsl2InitResult
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Indicates the result of the last full initialization performed "Indicates the result of the last full initialization performed
on the line. It is an enumeration type with the following on the line. It is an enumeration type with the following
values: noFail(0), configError(1), configNotFeasible(2), values: noFail(0), configError(1), configNotFeasible(2),
commFail(3), noPeerAtu(4), otherCause(5)." commFail(3), noPeerAtu(4), or otherCause(5)."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.3" REFERENCE "ITU-T G.997.1, paragraph 7.5.1.3"
::= { adsl2LineEntry 9 } ::= { adsl2LineEntry 9 }
adsl2LineStatusLastStateDs OBJECT-TYPE adsl2LineStatusLastStateDs OBJECT-TYPE
SYNTAX Adsl2LastTransmittedState SYNTAX Adsl2LastTransmittedState
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The last successful transmitted initialization state in "The last successful transmitted initialization state in
the downstream direction in the last full initialization the downstream direction in the last full initialization
skipping to change at page 50, line 4 skipping to change at page 50, line 9
adsl2LineStatusAtuc OBJECT-TYPE adsl2LineStatusAtuc OBJECT-TYPE
SYNTAX Adsl2LineStatus SYNTAX Adsl2LineStatus
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Indicates current state (existing failures) of the ATU-C. "Indicates current state (existing failures) of the ATU-C.
This is a bit-map of possible conditions. " This is a bit-map of possible conditions. "
REFERENCE "ITU-T G.997.1, paragraph 7.1.1.1" REFERENCE "ITU-T G.997.1, paragraph 7.1.1.1"
::= { adsl2LineEntry 13 } ::= { adsl2LineEntry 13 }
adsl2LineStatusLnAttenDs OBJECT-TYPE adsl2LineStatusLnAttenDs OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647) SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The measured difference in the total power transmitted by the "The measured difference in the total power transmitted by the
ATU-C and the total power received by the ATU-R over all sub- ATU-C and the total power received by the ATU-R over all sub-
carriers during diagnostics mode and initialization. It carriers during diagnostics mode and initialization. It
ranges from 0 to 1270 units of 0.1 dB (Physical values ranges from 0 to 1270 units of 0.1 dB (physical values
are 0 to 127 dB). are 0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the line A special value of 0x7FFFFFFF (2147483647) indicates the line
attenuation is out of range to be represented. attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the line A special value of 0x7FFFFFFE (2147483646) indicates the line
attenuation measurement is currently unavailable." attenuation measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.6" REFERENCE "ITU-T G.997.1, paragraph 7.5.1.6"
::= { adsl2LineEntry 14 } ::= { adsl2LineEntry 14 }
adsl2LineStatusLnAttenUs OBJECT-TYPE adsl2LineStatusLnAttenUs OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647) SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The measured difference in the total power transmitted by the "The measured difference in the total power transmitted by the
ATU-R and the total power received by the ATU-C over all sub- ATU-R and the total power received by the ATU-C over all sub-
carriers during diagnostics mode and initialization. carriers during diagnostics mode and initialization.
It ranges from 0 to 1270 units of 0.1 dB (Physical values are It ranges from 0 to 1270 units of 0.1 dB (physical values are
0 to 127 dB). 0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the line A special value of 0x7FFFFFFF (2147483647) indicates the line
attenuation is out of range to be represented. attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the line A special value of 0x7FFFFFFE (2147483646) indicates the line
attenuation measurement is currently unavailable." attenuation measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.7" REFERENCE "ITU-T G.997.1, paragraph 7.5.1.7"
::= { adsl2LineEntry 15 } ::= { adsl2LineEntry 15 }
adsl2LineStatusSigAttenDs OBJECT-TYPE adsl2LineStatusSigAttenDs OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647) SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The measured difference in the total power transmitted by the "The measured difference in the total power transmitted by the
ATU-C and the total power received by the ATU-R over all sub- ATU-C and the total power received by the ATU-R over all sub-
carriers during Showtime. It ranges from 0 to 1270 units of carriers during Showtime. It ranges from 0 to 1270 units of
0.1 dB (Physical values are 0 to 127 dB). 0.1 dB (physical values are 0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the A special value of 0x7FFFFFFF (2147483647) indicates the
signal attenuation is out of range to be represented. signal attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the A special value of 0x7FFFFFFE (2147483646) indicates the
signal attenuation measurement is currently unavailable." signal attenuation measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.8" REFERENCE "ITU-T G.997.1, paragraph 7.5.1.8"
::= { adsl2LineEntry 16 } ::= { adsl2LineEntry 16 }
adsl2LineStatusSigAttenUs OBJECT-TYPE adsl2LineStatusSigAttenUs OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647) SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
skipping to change at page 51, line 19 skipping to change at page 51, line 24
adsl2LineStatusSigAttenUs OBJECT-TYPE adsl2LineStatusSigAttenUs OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647) SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The measured difference in the total power transmitted by the "The measured difference in the total power transmitted by the
ATU-R and the total power received by the ATU-C over all sub- ATU-R and the total power received by the ATU-C over all sub-
carriers during Showtime. It ranges from 0 to 1270 units of carriers during Showtime. It ranges from 0 to 1270 units of
0.1 dB (Physical values are 0 to 127 dB). 0.1 dB (physical values are 0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the A special value of 0x7FFFFFFF (2147483647) indicates the
signal attenuation is out of range to be represented. signal attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the A special value of 0x7FFFFFFE (2147483646) indicates the
signal attenuation measurement is currently unavailable." signal attenuation measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.9" REFERENCE "ITU-T G.997.1, paragraph 7.5.1.9"
::= { adsl2LineEntry 17 } ::= { adsl2LineEntry 17 }
adsl2LineStatusSnrMarginDs OBJECT-TYPE adsl2LineStatusSnrMarginDs OBJECT-TYPE
SYNTAX Integer32 (-640..630 | 2147483646 | 2147483647) SYNTAX Integer32 (-640..630 | 2147483646 | 2147483647)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Downstream SNR Margin is the maximum increase in dB of the "Downstream SNR Margin is the maximum increase in dB of the
noise power received at the ATU-R, such that the BER noise power received at the ATU-R, such that the BER
requirements are met for all downstream bearer channels. It requirements are met for all downstream bearer channels. It
ranges from -640 to 630 units of 0.1 dB (Physical values are ranges from -640 to 630 units of 0.1 dB (physical values are
-64 to 63 dB). -64 to 63 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the A special value of 0x7FFFFFFF (2147483647) indicates the
SNR Margin is out of range to be represented. SNR Margin is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the A special value of 0x7FFFFFFE (2147483646) indicates the
SNR Margin measurement is currently unavailable." SNR Margin measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.10" REFERENCE "ITU-T G.997.1, paragraph 7.5.1.10"
::= { adsl2LineEntry 18 } ::= { adsl2LineEntry 18 }
adsl2LineStatusSnrMarginUs OBJECT-TYPE adsl2LineStatusSnrMarginUs OBJECT-TYPE
SYNTAX Integer32 (-640..630 | 2147483646 | 2147483647) SYNTAX Integer32 (-640..630 | 2147483646 | 2147483647)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Upstream SNR Margin is the maximum increase in dB of the noise "Upstream SNR Margin is the maximum increase in dB of the noise
power received at the ATU-C, such that the BER requirements power received at the ATU-C, such that the BER requirements
are met for all downstream bearer channels. It ranges from are met for all downstream bearer channels. It ranges from
-640 to 630 units of 0.1 dB (Physical values are -64 to -640 to 630 units of 0.1 dB (physical values are -64 to
63 dB). 63 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the A special value of 0x7FFFFFFF (2147483647) indicates the
SNR Margin is out of range to be represented. SNR Margin is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the A special value of 0x7FFFFFFE (2147483646) indicates the
SNR Margin measurement is currently unavailable." SNR Margin measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.11" REFERENCE "ITU-T G.997.1, paragraph 7.5.1.11"
::= { adsl2LineEntry 19 } ::= { adsl2LineEntry 19 }
adsl2LineStatusAttainableRateDs OBJECT-TYPE adsl2LineStatusAttainableRateDs OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
UNITS "bits/second" UNITS "bits/second"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Maximum Attainable Data Rate Downstream. "Maximum Attainable Data Rate Downstream.
The maximum downstream net data rate currently attainable by The maximum downstream net data rate currently attainable by
the ATU-C transmitter and the ATU-R receiver, coded in bit/s." the ATU-C transmitter and the ATU-R receiver, coded in
bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.12" REFERENCE "ITU-T G.997.1, paragraph 7.5.1.12"
::= { adsl2LineEntry 20 } ::= { adsl2LineEntry 20 }
adsl2LineStatusAttainableRateUs OBJECT-TYPE adsl2LineStatusAttainableRateUs OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
UNITS "bits/second" UNITS "bits/second"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Maximum Attainable Data Rate Upstream. "Maximum Attainable Data Rate Upstream.
The maximum upstream net data rate currently attainable by the The maximum upstream net data rate currently attainable by the
ATU-R transmitter and the ATU-C receiver, coded in bit/s." ATU-R transmitter and the ATU-C receiver, coded in
bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.13" REFERENCE "ITU-T G.997.1, paragraph 7.5.1.13"
::= { adsl2LineEntry 21 } ::= { adsl2LineEntry 21 }
adsl2LineStatusActPsdDs OBJECT-TYPE adsl2LineStatusActPsdDs OBJECT-TYPE
SYNTAX Integer32 (-900..0 | 2147483647) SYNTAX Integer32 (-900..0 | 2147483647)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Actual Power Spectrum Density (PSD) Downstream. The average "Actual Power Spectrum Density (PSD) Downstream. The average
downstream transmit PSD over the sub-carriers used for downstream transmit PSD over the sub-carriers used for
downstream. It ranges from -900 to 0 units of 0.1 dB downstream. It ranges from -900 to 0 units of 0.1 dB
(Physical values are -90 to 0 dBm/Hz). (physical values are -90 to 0 dBm/Hz).
A value of 0x7FFFFFFF (2147483647) indicates the measurement A value of 0x7FFFFFFF (2147483647) indicates the measurement
is out of range to be represented." is out of range to be represented."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.14" REFERENCE "ITU-T G.997.1, paragraph 7.5.1.14"
::= { adsl2LineEntry 22 } ::= { adsl2LineEntry 22 }
adsl2LineStatusActPsdUs OBJECT-TYPE adsl2LineStatusActPsdUs OBJECT-TYPE
SYNTAX Integer32 (-900..0 | 2147483647) SYNTAX Integer32 (-900..0 | 2147483647)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Actual Power Spectrum Density (PSD) Upstream. The average "Actual Power Spectrum Density (PSD) Upstream. The average
upstream transmit PSD over the sub-carriers used for upstream. upstream transmit PSD over the sub-carriers used for upstream.
It ranges from -900 to 0 units of 0.1 dB (Physical values It ranges from -900 to 0 units of 0.1 dB (physical values
are -90 to 0 dBm/Hz). are -90 to 0 dBm/Hz).
A value of 0x7FFFFFFF (2147483647) indicates the measurement A value of 0x7FFFFFFF (2147483647) indicates the measurement
is out of range to be represented." is out of range to be represented."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.15" REFERENCE "ITU-T G.997.1, paragraph 7.5.1.15"
::= { adsl2LineEntry 23 } ::= { adsl2LineEntry 23 }
adsl2LineStatusActAtpDs OBJECT-TYPE adsl2LineStatusActAtpDs OBJECT-TYPE
SYNTAX Integer32 (-310..310 | 2147483647) SYNTAX Integer32 (-310..310 | 2147483647)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Actual Aggregate Transmit Power Downstream. The total amount "Actual Aggregate Transmit Power Downstream. The total amount
of transmit power delivered by the ATU-C at the U-C reference of transmit power delivered by the ATU-C at the U-C reference
point, at the instant of measurement. It ranges from -310 to point, at the instant of measurement. It ranges from -310 to
310 units of 0.1 dB (Physical values are -31 to 31 dBm). 310 units of 0.1 dB (physical values are -31 to 31 dBm).
A value of 0x7FFFFFFF (2147483647) indicates the measurement A value of 0x7FFFFFFF (2147483647) indicates the measurement
is out of range to be represented." is out of range to be represented."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.16" REFERENCE "ITU-T G.997.1, paragraph 7.5.1.16"
::= { adsl2LineEntry 24 } ::= { adsl2LineEntry 24 }
adsl2LineStatusActAtpUs OBJECT-TYPE adsl2LineStatusActAtpUs OBJECT-TYPE
SYNTAX Integer32 (-310..310 | 2147483647) SYNTAX Integer32 (-310..310 | 2147483647)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Actual Aggregate Transmit Power Upstream. The total amount of "Actual Aggregate Transmit Power Upstream. The total amount of
transmit power delivered by the ATU-R at the U-R transmit power delivered by the ATU-R at the U-R
reference point, at the instant of measurement. It ranges reference point, at the instant of measurement. It ranges
from -310 to 310 units of 0.1 dB (Physical values are -31 from -310 to 310 units of 0.1 dB (physical values are -31
to 31 dBm). to 31 dBm).
A value of 0x7FFFFFFF (2147483647) indicates the measurement A value of 0x7FFFFFFF (2147483647) indicates the measurement
is out of range to be represented." is out of range to be represented."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.17" REFERENCE "ITU-T G.997.1, paragraph 7.5.1.17"
::= { adsl2LineEntry 25 } ::= { adsl2LineEntry 25 }
------------------------------------------------ ------------------------------------------------
-- adsl2ChannelStatusTable -- -- adsl2ChannelStatusTable --
------------------------------------------------ ------------------------------------------------
adsl2ChannelStatusTable OBJECT-TYPE adsl2ChannelStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2ChannelStatusEntry SYNTAX SEQUENCE OF Adsl2ChannelStatusEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2ChannelStatusTable contains status "The table adsl2ChannelStatusTable contains status
parameters of ADSL2 channel. This table contains live data parameters of the ADSL2 channel. This table contains live
from equipment. " data from equipment."
::= { adsl2Status 1 } ::= { adsl2Status 1 }
adsl2ChannelStatusEntry OBJECT-TYPE adsl2ChannelStatusEntry OBJECT-TYPE
SYNTAX Adsl2ChannelStatusEntry SYNTAX Adsl2ChannelStatusEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2ChannelStatusTable contains status "The table adsl2ChannelStatusTable contains status
parameters of ADSL2 channel. parameters of the ADSL2 channel.
The index of this table is an interface index where The index of this table consists of an interface index, where
the interface has an ifType value that is applicable the interface has an ifType value that is applicable
for a DSL channel and the termination unit." for a DSL channel, along with a termination unit."
INDEX { ifIndex, adsl2ChStatusUnit } INDEX { ifIndex, adsl2ChStatusUnit }
::= { adsl2ChannelStatusTable 1 } ::= { adsl2ChannelStatusTable 1 }
Adsl2ChannelStatusEntry ::= Adsl2ChannelStatusEntry ::=
SEQUENCE { SEQUENCE {
adsl2ChStatusUnit Adsl2Unit, adsl2ChStatusUnit Adsl2Unit,
adsl2ChStatusChannelNum Unsigned32, adsl2ChStatusChannelNum Unsigned32,
adsl2ChStatusActDataRate Unsigned32, adsl2ChStatusActDataRate Unsigned32,
adsl2ChStatusPrevDataRate Unsigned32, adsl2ChStatusPrevDataRate Unsigned32,
adsl2ChStatusActDelay Unsigned32, adsl2ChStatusActDelay Unsigned32,
adsl2ChStatusAtmStatus Adsl2ChAtmStatus, adsl2ChStatusAtmStatus Adsl2ChAtmStatus,
adsl2ChStatusPtmStatus Adsl2ChPtmStatus adsl2ChStatusPtmStatus Adsl2ChPtmStatus
} }
adsl2ChStatusUnit OBJECT-TYPE adsl2ChStatusUnit OBJECT-TYPE
SYNTAX Adsl2Unit SYNTAX Adsl2Unit
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The termination unit ATUC(1) or ATUR(2)." "The termination unit atuc(1) or atur(2)."
::= { adsl2ChannelStatusEntry 1 } ::= { adsl2ChannelStatusEntry 1 }
adsl2ChStatusChannelNum OBJECT-TYPE adsl2ChStatusChannelNum OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Provides the bearer channel number associated with this "Provides the bearer channel number associated with this
row (i.e., the channel ifIndex). row (i.e., the channel ifIndex).
This enables determining the channel configuration profile This enables determining the channel configuration profile
skipping to change at page 55, line 21 skipping to change at page 55, line 30
adsl2ChStatusActDataRate OBJECT-TYPE adsl2ChStatusActDataRate OBJECT-TYPE
SYNTAX Unsigned32(0..200000000) SYNTAX Unsigned32(0..200000000)
UNITS "bits/second" UNITS "bits/second"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The actual net data rate that the bearer channel is operating "The actual net data rate that the bearer channel is operating
at, if in L0 power management state. In L1 or L2 states, it at, if in L0 power management state. In L1 or L2 states, it
relates to the previous L0 state. The data rate is coded in relates to the previous L0 state. The data rate is coded in
bit/s." bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.5.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.5.2.1"
::= { adsl2ChannelStatusEntry 3 } ::= { adsl2ChannelStatusEntry 3 }
adsl2ChStatusPrevDataRate OBJECT-TYPE adsl2ChStatusPrevDataRate OBJECT-TYPE
SYNTAX Unsigned32(0..200000000) SYNTAX Unsigned32(0..200000000)
UNITS "bits/second" UNITS "bits/second"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The previous net data rate that the bearer channel was "The previous net data rate that the bearer channel was
operating at just before the latest rate change event. This operating at just before the latest rate change event. This
could be a full or short initialization, fast retrain, DRA or could be a full or short initialization, fast retrain, DRA or
power management transitions, excluding transitions between L0 power management transitions, excluding transitions between L0
state and L1 or L2 states. The data rate is coded in bit/s." state and L1 or L2 states. The data rate is coded in
bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.5.2.2" REFERENCE "ITU-T G.997.1, paragraph 7.5.2.2"
::= { adsl2ChannelStatusEntry 4 } ::= { adsl2ChannelStatusEntry 4 }
adsl2ChStatusActDelay OBJECT-TYPE adsl2ChStatusActDelay OBJECT-TYPE
SYNTAX Unsigned32(0..8176) SYNTAX Unsigned32(0..8176)
UNITS "milliseconds" UNITS "milliseconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The actual one-way interleaving delay introduced by the "The actual one-way interleaving delay introduced by the
skipping to change at page 56, line 4 skipping to change at page 56, line 14
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The actual one-way interleaving delay introduced by the "The actual one-way interleaving delay introduced by the
PMS-TC in the direction of the bearer channel, if in L0 PMS-TC in the direction of the bearer channel, if in L0
power management state. In L1 or L2 states, it relates to power management state. In L1 or L2 states, it relates to
the previous L0 state. It is coded in ms (rounded to the the previous L0 state. It is coded in ms (rounded to the
nearest ms)." nearest ms)."
REFERENCE "ITU-T G.997.1, paragraph 7.5.2.3" REFERENCE "ITU-T G.997.1, paragraph 7.5.2.3"
::= { adsl2ChannelStatusEntry 5 } ::= { adsl2ChannelStatusEntry 5 }
adsl2ChStatusAtmStatus OBJECT-TYPE adsl2ChStatusAtmStatus OBJECT-TYPE
SYNTAX Adsl2ChAtmStatus SYNTAX Adsl2ChAtmStatus
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Indicates current state (existing failures) of the ADSL "Indicates the current state (existing failures) of the ADSL
channel in case its Data Path is ATM. This is a bit-map of channel in case its Data Path is ATM. This is a bit-map of
possible conditions. The various bit positions are: possible conditions. The various bit positions are:
noDefect (0), noDefect (0),
noCellDelineation(1), noCellDelineation(1), or
lossOfCellDelineation (2). lossOfCellDelineation (2).
In case the channel is not of ATM Data Path the object is set In the case where the channel is not an ATM Data Path, the
to '0'." object is set to '0'."
REFERENCE "ITU-T G.997.1, paragraph 7.1.4" REFERENCE "ITU-T G.997.1, paragraph 7.1.4"
::= { adsl2ChannelStatusEntry 6 } ::= { adsl2ChannelStatusEntry 6 }
adsl2ChStatusPtmStatus OBJECT-TYPE adsl2ChStatusPtmStatus OBJECT-TYPE
SYNTAX Adsl2ChPtmStatus SYNTAX Adsl2ChPtmStatus
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Indicates current state (existing failures) of the ADSL "Indicates the current state (existing failures) of the ADSL
channel in case its Data Path is PTM. This is a bit-map of channel in case its Data Path is PTM. This is a bit-map of
possible conditions. The various bit positions are: possible conditions. The various bit positions are:
noDefect (0), noDefect(0), or
outOfSync (1). outOfSync (1).
In case the channel is not of PTM Data Path the object is set In the case where the channel is not a PTM Data Path, the
to '0'." object is set to '0'."
REFERENCE "ITU-T G.997.1, paragraph 7.1.5" REFERENCE "ITU-T G.997.1, paragraph 7.1.5"
::= { adsl2ChannelStatusEntry 7 } ::= { adsl2ChannelStatusEntry 7 }
------------------------------------------------ ------------------------------------------------
-- Scalars that relate to the adsl2SCStatusTable. -- Scalars that relate to the adsl2SCStatusTable.
------------------------------------------------ ------------------------------------------------
adsl2ScalarSCMaxInterfaces OBJECT-TYPE adsl2ScalarSCMaxInterfaces OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-only MAX-ACCESS read-only
skipping to change at page 57, line 23 skipping to change at page 57, line 34
------------------------------------------------ ------------------------------------------------
-- adsl2SCStatusTable -- -- adsl2SCStatusTable --
------------------------------------------------ ------------------------------------------------
adsl2SCStatusTable OBJECT-TYPE adsl2SCStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2SCStatusEntry SYNTAX SEQUENCE OF Adsl2SCStatusEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2SCStatusTable contains status parameters "The table adsl2SCStatusTable contains status parameters
of ADSL2 sub-carriers. This following points apply to this of the ADSL2 sub-carriers. The following points apply to this
table : table :
1. The main purpose of this table is to hold the results 1. The main purpose of this table is to hold the results
of a DELT test. of a DELT.
2. This table also holds parameters obtained at line 2. This table also holds parameters obtained at line
initialisation time. initialization time.
3. The rows in this table are volatile, that is they are 3. The rows in this table are volatile; that is, they are
lost if the SNMP agent is rebooted. lost if the SNMP agent is rebooted.
4. Due to the large OCTET STRING attributes in this table, 4. Due to the large OCTET STRING attributes in this table,
the worst case memory requirements for this table are the worst case memory requirements for this table are
very high. The manager may use the row status attribute very high. The manager may use the row status attribute
of this table to delete rows in order to reclaim memory. of this table to delete rows in order to reclaim memory.
5. The manager may create rows in this table. The SNMP 5. The manager may create rows in this table. The SNMP
agent may create rows in this table. Only the manager agent may create rows in this table. Only the manager
may delete rows in this table. may delete rows in this table.
6. The maximum number of rows allowable in this table is 6. The maximum number of rows allowable in this table is
indicated by the scalar attribute indicated by the scalar attribute
skipping to change at page 57, line 41 skipping to change at page 58, line 4
4. Due to the large OCTET STRING attributes in this table, 4. Due to the large OCTET STRING attributes in this table,
the worst case memory requirements for this table are the worst case memory requirements for this table are
very high. The manager may use the row status attribute very high. The manager may use the row status attribute
of this table to delete rows in order to reclaim memory. of this table to delete rows in order to reclaim memory.
5. The manager may create rows in this table. The SNMP 5. The manager may create rows in this table. The SNMP
agent may create rows in this table. Only the manager agent may create rows in this table. Only the manager
may delete rows in this table. may delete rows in this table.
6. The maximum number of rows allowable in this table is 6. The maximum number of rows allowable in this table is
indicated by the scalar attribute indicated by the scalar attribute
adsl2ScalarSCMaxInterfaces. adsl2ScalarSCMaxInterfaces.
The number of rows available in this table is indicated The number of rows available in this table is indicated
by the scalar attribute adsl2ScalarSCAvailInterfaces. by the scalar attribute adsl2ScalarSCAvailInterfaces.
7. The SNMP agent is permitted to create rows in this table 7. The SNMP agent is permitted to create rows in this table
when a DELT test completes successfully or when line when a DELT completes successfully or when line
initialisation occurs. It is not mandatory for the SNMP initialization occurs. It is not mandatory for the SNMP
agent to create rows in this table, hence it may be agent to create rows in this table; hence, it may be
necessary for the manager to create rows in this table necessary for the manager to create rows in this table
before any results can be stored. before any results can be stored.
8. If the manager attempts to create a row in this table 8. If the manager attempts to create a row in this table
and there are no more rows available, the creation and there are no more rows available, the creation
attempt will fail and the response to the SNMP SET PDU attempt will fail, and the response to the SNMP SET PDU
will contain the error noCreation(11). will contain the error noCreation(11).
9. If the SNMP agent attempts to create a row in this table 9. If the SNMP agent attempts to create a row in this table
and there are no more rows available, the creation and there are no more rows available, the creation
attempt will fail and the attribute attempt will fail, and the attribute
adsl2LineCmndConfLdsfFailReason will indicate the adsl2LineCmndConfLdsfFailReason will indicate the
reason for the failure. The failure reason will be either reason for the failure. The failure reason will be either
tableFull(10) or noResources(11). tableFull(10) or noResources(11).
10. An example of use of this table is as follows : 10. An example of use of this table is as follows :
Step 1. : The DELT test is started by setting the Step 1. : The DELT is started by setting the
: adsl2LineCmndConfLdsf from inhibit to force. : adsl2LineCmndConfLdsf from inhibit to force.
Step 2. : The DELT test completes and valid data is Step 2. : The DELT completes, and valid data is
: available. : available.
Step 3. : The row in the adsl2SCStatusTable where the Step 3. : The row in the adsl2SCStatusTable where the
: results will be stored does not yet exist so : results will be stored does not yet exist so
: the SNMP agent attempts to create the row. : the SNMP agent attempts to create the row.
Step 4. : Due to a low memory condition, a row in the Step 4. : Due to a low memory condition, a row in the
: adsl2SCStatusTable table cannot be created at : adsl2SCStatusTable table cannot be created at
: this time. : this time.
Step 5. : The reason for the failure, tableFull(10), is Step 5. : The reason for the failure, tableFull(10), is
: indicated in the adsl2LineCmndConfLdsfFailReason : indicated in the adsl2LineCmndConfLdsfFailReason
: attribute. : attribute.
11. Another example of use of this table is as follows : 11. Another example of use of this table is as follows :
Step 1. : The DELT test is started by setting the Step 1. : The DELT is started by setting the
: adsl2LineCmndConfLdsf from inhibit to force. : adsl2LineCmndConfLdsf from inhibit to force.
Step 2. : The DELT test completes and valid data is Step 2. : The DELT completes and valid data is
: available. : available.
Step 3. : The row in the adsl2SCStatusTable where the Step 3. : The row in the adsl2SCStatusTable where the
: results will be stored does not yet exist so : results will be stored does not yet exist so
: the SNMP agent attempts to create the row. : the SNMP agent attempts to create the row.
Step 4. : The row creation is successfully. Step 4. : The row creation is successful.
Step 5. : The value of the attribute Step 5. : The value of the attribute
: adsl2LineCmndConfLdsfFailReasonreason is set : adsl2LineCmndConfLdsfFailReasonreason is set
: to success(2). : to success(2).
12. Another example of use of this table is as follows : 12. Another example of use of this table is as follows :
Step 1. : The manager creates a row in adsl2SCStatusTable Step 1. : The manager creates a row in adsl2SCStatusTable
: for a particular ADSL2 line. : for a particular ADSL2 line.
Step 2. : The DELT test is started on the above mentioned Step 2. : The DELT is started on the above-mentioned
: line by setting the adsl2LineCmndConfLdsf from : line by setting the adsl2LineCmndConfLdsf from
: inhibit to force. : inhibit to force.
Step 3. : The DELT test completes and valid data is Step 3. : The DELT completes, and valid data is
: available. : available.
Step 4. : The value of the attribute Step 4. : The value of the attribute
: adsl2LineCmndConfLdsfFailReasonreason is set : adsl2LineCmndConfLdsfFailReasonreason is set
: to success(2)." : to success(2)."
::= { adsl2Status 2 } ::= { adsl2Status 2 }
adsl2SCStatusEntry OBJECT-TYPE adsl2SCStatusEntry OBJECT-TYPE
SYNTAX Adsl2SCStatusEntry SYNTAX Adsl2SCStatusEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table Hfadsl2SCStatusEntry contains status parameters "The table Adsl2SCStatusEntry contains status parameters
of ADSL2 sub-carriers. of the ADSL2 sub-carriers.
The index of this table is an interface index where the The index of this table is an interface index where the
interface has an ifType of adsl2(230)." interface has an ifType of adsl2plus(238)."
INDEX { ifIndex, adsl2SCStatusDirection } INDEX { ifIndex, adsl2SCStatusDirection }
::= { adsl2SCStatusTable 1 } ::= { adsl2SCStatusTable 1 }
Adsl2SCStatusEntry ::= Adsl2SCStatusEntry ::=
SEQUENCE { SEQUENCE {
adsl2SCStatusDirection Adsl2Direction, adsl2SCStatusDirection Adsl2Direction,
adsl2SCStatusMtime Unsigned32, adsl2SCStatusMtime Unsigned32,
adsl2SCStatusSnr OCTET STRING, adsl2SCStatusSnr OCTET STRING,
adsl2SCStatusBitsAlloc OCTET STRING, adsl2SCStatusBitsAlloc OCTET STRING,
adsl2SCStatusGainAlloc OCTET STRING, adsl2SCStatusGainAlloc OCTET STRING,
skipping to change at page 59, line 42 skipping to change at page 60, line 5
adsl2SCStatusAttainableRate Unsigned32, adsl2SCStatusAttainableRate Unsigned32,
adsl2SCStatusActAtp Integer32, adsl2SCStatusActAtp Integer32,
adsl2SCStatusRowStatus RowStatus adsl2SCStatusRowStatus RowStatus
} }
adsl2SCStatusDirection OBJECT-TYPE adsl2SCStatusDirection OBJECT-TYPE
SYNTAX Adsl2Direction SYNTAX Adsl2Direction
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The direction of the sub-carrier either "The direction of the sub-carrier is either
upstream or downstream" upstream or downstream."
::= { adsl2SCStatusEntry 1 } ::= { adsl2SCStatusEntry 1 }
adsl2SCStatusMtime OBJECT-TYPE adsl2SCStatusMtime OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
UNITS "symbols" UNITS "symbols"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"SNR Measurement Time. The number of symbols used to "SNR Measurement Time. The number of symbols used to
measure the SNR values on the respective transmission measure the SNR values on the respective transmission
direction. It should correspond to the value specified in the direction. It should correspond to the value specified in the
recommendation (e.g., the number of symbols in 1 second recommendation (e.g., the number of symbols in 1 second
time interval for G.992.3). This parameter corresponds to time interval for G.992.3). This parameter corresponds to
1 second in loop diagnostic procedure and should be updated 1 second in loop diagnostic procedure and should be updated
otherwise" otherwise."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.20.1 (SNRMTds) REFERENCE "ITU-T G.997.1, paragraph 7.5.1.20.1 (SNRMTds)
and paragraph 7.5.1.20.3 (SNRMTus)" and paragraph 7.5.1.20.3 (SNRMTus)"
::= { adsl2SCStatusEntry 2 } ::= { adsl2SCStatusEntry 2 }
adsl2SCStatusSnr OBJECT-TYPE adsl2SCStatusSnr OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..512)) SYNTAX OCTET STRING (SIZE(0..512))
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The SNR Margin per sub-carrier, expressing the ratio between "The SNR Margin per sub-carrier, expressing the ratio between
the received signal power and received noise power per the received signal power and received noise power per
subscriber. It is an array of 512 octets, designed for subscriber. It is an array of 512 octets, designed for
supporting up to 512 (downstream) sub-carriers. supporting up to 512 (downstream) sub-carriers.
The number of utilized octets on downstream direction depends The number of utilized octets on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This on NSCds, and on upstream direction it depends on NSCus. This
value is referred here as NSC. value is referred to here as NSC.
Octet i (0 <= i < NSC) is set to a value in the range 0 to Octet i (0 <= i < NSC) is set to a value in the range 0 to
254 to indicate that the respective downstream or upstream sub- 254 to indicate that the respective downstream or upstream sub-
carrier i has SNR of: (-32 + Adsl2SubcarrierSnr(i)/2) in dB carrier i has SNR of: (-32 + Adsl2SubcarrierSnr(i)/2) in dB
(i.e., -32 to 95dB). (i.e., -32 to 95dB).
The special value 255 means that no measurement could be done The special value 255 means that no measurement could be done
for the subcarrier because it is out of the PSD mask passband for the subcarrier because it is out of the PSD mask passband
or that the noise PSD is out of range to be represented. or that the noise PSD is out of range to be represented.
Each value in this array is 8 bits wide." Each value in this array is 8 bits wide."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.20.2 (SNRpsds) REFERENCE "ITU-T G.997.1, paragraph 7.5.1.20.2 (SNRpsds)
and paragraph 7.5.1.20.4 (SNRpsus)" and paragraph 7.5.1.20.4 (SNRpsus)"
skipping to change at page 60, line 50 skipping to change at page 61, line 13
SYNTAX OCTET STRING (SIZE(0..256)) SYNTAX OCTET STRING (SIZE(0..256))
UNITS "bits" UNITS "bits"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The bits allocation per sub-carrier. An array of 256 octets "The bits allocation per sub-carrier. An array of 256 octets
(512 nibbles), designed for supporting up to 512 (downstream) (512 nibbles), designed for supporting up to 512 (downstream)
sub-carriers. sub-carriers.
The number of utilized nibbles on downstream direction depends The number of utilized nibbles on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This on NSCds, and on upstream direction it depends on NSCus. This
value is referred here as NSC. value is referred to here as NSC.
Nibble i (0 <= i < NSC) is set to a value in the range 0 Nibble i (0 <= i < NSC) is set to a value in the range 0
to 15 to indicate that the respective downstream or upstream to 15 to indicate that the respective downstream or upstream
sub-carrier i has the same amount of bits allocation." sub-carrier i has the same amount of bits allocation."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.21.1 (BITSpsds) REFERENCE "ITU-T G.997.1, paragraph 7.5.1.21.1 (BITSpsds)
and paragraph 7.5.1.21.2 (BITSpsus)" and paragraph 7.5.1.21.2 (BITSpsus)"
::= { adsl2SCStatusEntry 4 } ::= { adsl2SCStatusEntry 4 }
adsl2SCStatusGainAlloc OBJECT-TYPE adsl2SCStatusGainAlloc OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..1024)) SYNTAX OCTET STRING (SIZE(0..1024))
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The gain allocation per sub-carrier. An array of 512 16-bits "The gain allocation per sub-carrier. An array of 512 16-bits
values, designed for supporting up to 512 (downstream) sub- values, designed for supporting up to 512 (downstream) sub-
carriers. carriers.
The number of utilized octets on downstream direction depends The number of utilized octets on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This on NSCds, and on upstream direction it depends on NSCus. This
value is referred here as NSC. value is referred to here as NSC.
Value i (0 <= i < NSC) is in the range 0 to 4093 to indicate Value i (0 <= i < NSC) is in the range 0 to 4093 to indicate
that the respective downstream or upstream sub-carrier i has the that the respective downstream or upstream sub-carrier i has the
same amount of gain value. same amount of gain value.
The gain value is represented as a multiple of 1/512 on The gain value is represented as a multiple of 1/512 on a
linear scale. Each value in this array is 16 bits wide and is linear scale. Each value in this array is 16 bits wide and is
stored in big endian format." stored in big endian format."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.21.3 (GAINSpsds) REFERENCE "ITU-T G.997.1, paragraph 7.5.1.21.3 (GAINSpsds)
and paragraph 7.5.1.21.4 (GAINSpsus)" and paragraph 7.5.1.21.4 (GAINSpsus)"
::= { adsl2SCStatusEntry 5 } ::= { adsl2SCStatusEntry 5 }
adsl2SCStatusTssi OBJECT-TYPE adsl2SCStatusTssi OBJECT-TYPE
SYNTAX Adsl2Tssi SYNTAX Adsl2Tssi
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
skipping to change at page 62, line 28 skipping to change at page 62, line 39
SYNTAX OCTET STRING (SIZE(0..1024)) SYNTAX OCTET STRING (SIZE(0..1024))
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An array of up to 512 complex H(f) linear representation "An array of up to 512 complex H(f) linear representation
values in linear scale for the respective transmission values in linear scale for the respective transmission
direction. It is designed to support up to 512 (downstream) direction. It is designed to support up to 512 (downstream)
sub-carriers. sub-carriers.
The number of utilized values on downstream direction depends The number of utilized values on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This on NSCds, and on upstream direction it depends on NSCus. This
value is referred here as NSC. value is referred to here as NSC.
Each array entry represents the real component [referred here as Each array entry represents the real component [referred to here
a(i)] of Hlin(f = i*Df) value for a particular sub-carrier index as a(i)] of Hlin(f = i*Df) value for a particular sub-carrier
i (0 <= i < NSC). index i (0 <= i < NSC).
Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)), Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)),
where scale is Adsl2SubcarrierLinScale and a(i) and b(i) where scale is Adsl2SubcarrierLinScale and a(i) and b(i)
[provided by the Adsl2SubcarrierLinImg object] are in the range [provided by the Adsl2SubcarrierLinImg object] are in the range
(-2^15+1) to (+2^15-1). (-2^15+1) to (+2^15-1).
A special value a(i)=b(i)= -2^15 indicates that no measurement A special value a(i)=b(i)= -2^15 indicates that no measurement
could be done for the subcarrier because it is out of the could be done for the subcarrier because it is out of the
passband or that the attenuation is out of range to be passband or that the attenuation is out of range to be
represented. This parameter is only available after a loop represented. This parameter is only available after a loop
diagnostic procedure. diagnostic procedure.
Each value in this array is 16 bits wide and is stored in big Each value in this array is 16 bits wide and is stored in big
endian format." endian format."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.18.2 (HLINpsds) REFERENCE "ITU-T G.997.1, paragraph 7.5.1.18.2 (HLINpsds)
and paragraph 7.5.1.18.6 (HLINpsds)" and paragraph 7.5.1.18.6 (HLINpsds)"
::= { adsl2SCStatusEntry 8 } ::= { adsl2SCStatusEntry 8 }
adsl2SCStatusLinImg OBJECT-TYPE adsl2SCStatusLinImg OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..1024)) SYNTAX OCTET STRING (SIZE(0..1024))
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
skipping to change at page 63, line 10 skipping to change at page 63, line 22
SYNTAX OCTET STRING (SIZE(0..1024)) SYNTAX OCTET STRING (SIZE(0..1024))
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An array of up to 512 complex H(f) linear representation "An array of up to 512 complex H(f) linear representation
values in linear scale for the respective transmission values in linear scale for the respective transmission
direction. It is designed to support up to 512 (downstream) direction. It is designed to support up to 512 (downstream)
sub-carriers. sub-carriers.
The number of utilized values on downstream direction depends The number of utilized values on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This on NSCds, and on upstream direction it depends on NSCus. This
value is referred here as NSC. value is referred to here as NSC.
Each array entry represents the imaginary component [referred Each array entry represents the imaginary component [referred
here as b(i)] of Hlin(f = i*Df) value for a particular sub- to here as b(i)] of Hlin(f = i*Df) value for a particular sub-
carrier index i (0 <= i < NSC). carrier index i (0 <= i < NSC).
Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)), Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)),
where scale is Adsl2SubcarrierLinScale and a(i) [provided by where scale is Adsl2SubcarrierLinScale and a(i) [provided by
the Adsl2SubcarrierLinReal object] and b(i) are in the range the Adsl2SubcarrierLinReal object] and b(i) are in the range
(-2^15+1) to (+2^15-1). (-2^15+1) to (+2^15-1).
A special value a(i)=b(i)= -2^15 indicates that no measurement A special value a(i)=b(i)= -2^15 indicates that no measurement
could be done for the subcarrier because it is out of the could be done for the subcarrier because it is out of the
passband or that the attenuation is out of range to be passband or that the attenuation is out of range to be
represented. This parameter is only available after a loop represented. This parameter is only available after a loop
diagnostic procedure. diagnostic procedure.
skipping to change at page 64, line 4 skipping to change at page 64, line 15
and paragraph 7.5.1.18.7 (HLOGMTus)" and paragraph 7.5.1.18.7 (HLOGMTus)"
::= { adsl2SCStatusEntry 10 } ::= { adsl2SCStatusEntry 10 }
adsl2SCStatusLog OBJECT-TYPE adsl2SCStatusLog OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..1024)) SYNTAX OCTET STRING (SIZE(0..1024))
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An array of up to 512 real H(f) logarithmic representation "An array of up to 512 real H(f) logarithmic representation
values in dB for the respective transmission direction. It is values in dB for the respective transmission direction. It is
designed to support up to 512 (downstream) sub-carriers designed to support up to 512 (downstream) sub-carriers.
The number of utilized values on downstream direction depends The number of utilized values on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This on NSCds, and on upstream direction it depends on NSCus. This
value is referred here as NSC. value is referred to here as NSC.
Each array entry represents the real Hlog(f = i*Df) value for a Each array entry represents the real Hlog(f = i*Df) value for a
particular sub-carrier index i, (0 <= i < NSC). particular sub-carrier index i, (0 <= i < NSC).
The real Hlog(f) value is represented as (6-m(i)/10), with m(i) The real Hlog(f) value is represented as (6-m(i)/10), with m(i)
in the range 0 to 1022. A special value m=1023 indicates that in the range 0 to 1022. A special value m=1023 indicates that
no measurement could be done for the subcarrier because it is no measurement could be done for the subcarrier because it is
out of the passband or that the attenuation is out of range to out of the passband or that the attenuation is out of range to
be represented. This parameter is applicable in loop be represented. This parameter is applicable in loop
diagnostic procedure and initialization. diagnostic procedure and initialization.
Each value in this array is 16 bits wide and is stored Each value in this array is 16 bits wide and is stored
in big endian format." in big endian format."
skipping to change at page 64, line 46 skipping to change at page 65, line 9
::= { adsl2SCStatusEntry 12 } ::= { adsl2SCStatusEntry 12 }
adsl2SCStatusQln OBJECT-TYPE adsl2SCStatusQln OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..512)) SYNTAX OCTET STRING (SIZE(0..512))
UNITS "dBm/Hz" UNITS "dBm/Hz"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An array of up to 512 real Quiet Line Noise values in dBm/Hz "An array of up to 512 real Quiet Line Noise values in dBm/Hz
for the respective transmission direction. It is designed for for the respective transmission direction. It is designed for
up to 512 (downstream) sub-carriers up to 512 (downstream) sub-carriers.
The number of utilized values on downstream direction depends The number of utilized values on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This on NSCds, and on upstream direction it depends on NSCus. This
value is referred here as NSC. value is referred to here as NSC.
Each array entry represents the QLN(f = i*Df) value for a Each array entry represents the QLN(f = i*Df) value for a
particular sub-carrier index i, (0 <= i < NSC). particular sub-carrier index i, (0 <= i < NSC).
The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the
range 0 to 254. A special value n(i)=255 indicates that no range 0 to 254. A special value n(i)=255 indicates that no
measurement could be done for the subcarrier because it is out measurement could be done for the subcarrier because it is out
of the passband or that the noise PSD is out of range to be of the passband or that the noise PSD is out of range to be
represented. represented.
This parameter is applicable in loop diagnostic procedure and This parameter is applicable in loop diagnostic procedure and
initialization. Each value in this array is 8 bits wide." initialization. Each value in this array is 8 bits wide."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.19.2 (QLNpsds) REFERENCE "ITU-T G.997.1, paragraph 7.5.1.19.2 (QLNpsds)
and paragraph 7.5.1.19.4 (QLNpsus)" and paragraph 7.5.1.19.4 (QLNpsus)"
::= { adsl2SCStatusEntry 13 } ::= { adsl2SCStatusEntry 13 }
skipping to change at page 65, line 30 skipping to change at page 65, line 40
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"When referring to the downstream direction, it is the measured "When referring to the downstream direction, it is the measured
difference in the total power transmitted by the ATU-C and the difference in the total power transmitted by the ATU-C and the
total power received by the ATU-R over all sub-carriers during total power received by the ATU-R over all sub-carriers during
diagnostics mode. diagnostics mode.
When referring to the upstream direction, it is the measured When referring to the upstream direction, it is the measured
difference in the total power transmitted by the ATU-R and the difference in the total power transmitted by the ATU-R and the
total power received by the ATU-C over all sub-carriers during total power received by the ATU-C over all sub-carriers during
diagnostics mode. diagnostics mode.
It ranges from 0 to 1270 units of 0.1 dB (Physical values are It ranges from 0 to 1270 units of 0.1 dB (physical values are
0 to 127 dB). 0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the line A special value of 0x7FFFFFFF (2147483647) indicates the line
attenuation is out of range to be represented. attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the line A special value of 0x7FFFFFFE (2147483646) indicates the line
attenuation measurement is unavailable. attenuation measurement is unavailable.
This object reflects the value of the parameter following the This object reflects the value of the parameter following the
most recent DELT performed on the associated line. Once most recent DELT performed on the associated line. Once
the DELT process is over, the parameter no longer changes the DELT process is over, the parameter no longer changes
until the row is deleted or a new DELT process is initiated. " until the row is deleted or a new DELT process is initiated. "
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.6 (LATNds) REFERENCE "ITU-T G.997.1, paragraph 7.5.1.6 (LATNds)
skipping to change at page 65, line 52 skipping to change at page 66, line 14
::= { adsl2SCStatusEntry 14 } ::= { adsl2SCStatusEntry 14 }
adsl2SCStatusSigAtten OBJECT-TYPE adsl2SCStatusSigAtten OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647) SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"When referring to the downstream direction, it is the measured "When referring to the downstream direction, it is the measured
difference in the total power transmitted by the difference in the total power transmitted by the
ATU-C and the total power received by the ATU-R over all sub ATU-C and the total power received by the ATU-R over all sub-
carriers during Showtime after the diagnostics mode. carriers during Showtime after the diagnostics mode.
When referring to the upstream direction, it is the measured When referring to the upstream direction, it is the measured
difference in the total power transmitted by the difference in the total power transmitted by the
ATU-R and the total power received by the ATU-C over all sub ATU-R and the total power received by the ATU-C over all sub-
carriers during Showtime after the diagnostics mode. carriers during Showtime after the diagnostics mode.
It ranges from 0 to 1270 units of 0.1 dB (Physical values It ranges from 0 to 1270 units of 0.1 dB (physical values
are 0 to 127 dB). are 0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the A special value of 0x7FFFFFFF (2147483647) indicates the
signal attenuation is out of range to be represented. signal attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the A special value of 0x7FFFFFFE (2147483646) indicates the
signal attenuation measurement is unavailable. signal attenuation measurement is unavailable.
This object reflects the value of the parameter following the This object reflects the value of the parameter following the
most recent DELT performed on the associated line. Once most recent DELT performed on the associated line. Once
the DELT process is over, the parameter no longer changes the DELT process is over, the parameter no longer changes
until the row is deleted or a new DELT process is initiated. " until the row is deleted or a new DELT process is initiated. "
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.8 (SATNds) REFERENCE "ITU-T G.997.1, paragraph 7.5.1.8 (SATNds)
skipping to change at page 66, line 33 skipping to change at page 66, line 44
adsl2SCStatusSnrMargin OBJECT-TYPE adsl2SCStatusSnrMargin OBJECT-TYPE
SYNTAX Integer32 (-640..630 | 2147483646 | 2147483647) SYNTAX Integer32 (-640..630 | 2147483646 | 2147483647)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"SNR Margin is the maximum increase in dB of the noise power "SNR Margin is the maximum increase in dB of the noise power
received at the ATU (ATU-R on downstream direction and ATU-C received at the ATU (ATU-R on downstream direction and ATU-C
on upstream direction), such that the BER requirements are met on upstream direction), such that the BER requirements are met
for all bearer channels received at the ATU. It ranges from for all bearer channels received at the ATU. It ranges from
-640 to 630 units of 0.1 dB (Physical values are -64 to -640 to 630 units of 0.1 dB (physical values are -64 to
63 dB). 63 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the A special value of 0x7FFFFFFF (2147483647) indicates the
SNR Margin is out of range to be represented. SNR Margin is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the A special value of 0x7FFFFFFE (2147483646) indicates the
SNR Margin measurement is currently unavailable. SNR Margin measurement is currently unavailable.
This object reflects the value of the parameter following the This object reflects the value of the parameter following the
most recent DELT performed on the associated line. Once most recent DELT performed on the associated line. Once
the DELT process is over, the parameter no longer changes the DELT process is over, the parameter no longer changes
until the row is deleted or a new DELT process is initiated. " until the row is deleted or a new DELT process is initiated. "
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.10 (SNRMds) REFERENCE "ITU-T G.997.1, paragraph 7.5.1.10 (SNRMds)
skipping to change at page 67, line 9 skipping to change at page 67, line 20
adsl2SCStatusAttainableRate OBJECT-TYPE adsl2SCStatusAttainableRate OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
UNITS "bits/second" UNITS "bits/second"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Maximum Attainable Data Rate. The maximum net data rate "Maximum Attainable Data Rate. The maximum net data rate
currently attainable by the ATU-C transmitter and ATU-R currently attainable by the ATU-C transmitter and ATU-R
receiver (when referring to downstream direction) or by the receiver (when referring to downstream direction) or by the
ATU-R transmitter and ATU-C receiver (when referring to ATU-R transmitter and ATU-C receiver (when referring to
upstream direction). Value is coded in bits/s. upstream direction). Value is coded in bits/second.
This object reflects the value of the parameter following the This object reflects the value of the parameter following the
most recent DELT performed on the associated line. Once most recent DELT performed on the associated line. Once
the DELT process is over, the parameter no longer changes the DELT process is over, the parameter no longer changes
until the row is deleted or a new DELT process is initiated. " until the row is deleted or a new DELT process is initiated. "
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.12 (ATTNDRds) REFERENCE "ITU-T G.997.1, paragraph 7.5.1.12 (ATTNDRds)
and paragraph 7.5.1.13 (ATTNDRus)" and paragraph 7.5.1.13 (ATTNDRus)"
::= { adsl2SCStatusEntry 17 } ::= { adsl2SCStatusEntry 17 }
adsl2SCStatusActAtp OBJECT-TYPE adsl2SCStatusActAtp OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Actual Aggregate Transmit Power from the ATU (ATU-R on "Actual Aggregate Transmit Power from the ATU (ATU-R on
downstream direction and ATU-C on upstream direction), at the downstream direction and ATU-C on upstream direction), at the
instant of measurement. It ranges from -310 to 310 units of instant of measurement. It ranges from -310 to 310 units of
0.1 dB (Physical values are -31 to 31 dBm). A value of all 0.1 dB (physical values are -31 to 31 dBm). A value of all
1's indicates the measurement is out of range to be 1's indicates the measurement is out of range to be
represented. represented.
This object reflects the value of the parameter following the This object reflects the value of the parameter following the
most recent DELT performed on the associated line. Once most recent DELT performed on the associated line. Once
the DELT process is over, the parameter no longer changes the DELT process is over, the parameter no longer changes
until the row is deleted or a new DELT process is initiated. " until the row is deleted or a new DELT process is initiated. "
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.16 (ACTATPds) REFERENCE "ITU-T G.997.1, paragraph 7.5.1.16 (ACTATPds)
and paragraph 7.5.1.17 (ACTATPus)" and paragraph 7.5.1.17 (ACTATPus)"
::= { adsl2SCStatusEntry 18 } ::= { adsl2SCStatusEntry 18 }
skipping to change at page 68, line 8 skipping to change at page 68, line 19
::= { adsl2SCStatusEntry 19 } ::= { adsl2SCStatusEntry 19 }
------------------------------------------------ ------------------------------------------------
-- adsl2LineInventoryTable -- -- adsl2LineInventoryTable --
------------------------------------------------ ------------------------------------------------
adsl2LineInventoryTable OBJECT-TYPE adsl2LineInventoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineInventoryEntry SYNTAX SEQUENCE OF Adsl2LineInventoryEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2LineInventoryTable contains inventory of ADSL2 "The table adsl2LineInventoryTable contains inventory of the
unit. " ADSL2 units."
::= { adsl2Inventory 1 } ::= { adsl2Inventory 1 }
adsl2LineInventoryEntry OBJECT-TYPE adsl2LineInventoryEntry OBJECT-TYPE
SYNTAX Adsl2LineInventoryEntry SYNTAX Adsl2LineInventoryEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2LineInventoryTable contains inventory of ADSL2 "The table adsl2LineInventoryTable contains inventory of the
unit. ADSL2 units.
The index of this table is an interface index where the The index of this table is an interface index where the
interface has an ifType of adsl2(230)." interface has an ifType of adsl2plus(238)."
INDEX { ifIndex, adsl2LInvUnit } INDEX { ifIndex, adsl2LInvUnit }
::= { adsl2LineInventoryTable 1 } ::= { adsl2LineInventoryTable 1 }
Adsl2LineInventoryEntry ::= Adsl2LineInventoryEntry ::=
SEQUENCE { SEQUENCE {
adsl2LInvUnit Adsl2Unit, adsl2LInvUnit Adsl2Unit,
adsl2LInvG994VendorId OCTET STRING, adsl2LInvG994VendorId OCTET STRING,
adsl2LInvSystemVendorId OCTET STRING, adsl2LInvSystemVendorId OCTET STRING,
adsl2LInvVersionNumber OCTET STRING, adsl2LInvVersionNumber OCTET STRING,
adsl2LInvSerialNumber OCTET STRING, adsl2LInvSerialNumber OCTET STRING,
adsl2LInvSelfTestResult Unsigned32, adsl2LInvSelfTestResult Unsigned32,
adsl2LInvTransmissionCapabilities Adsl2TransmissionModeType adsl2LInvTransmissionCapabilities Adsl2TransmissionModeType
} }
adsl2LInvUnit OBJECT-TYPE adsl2LInvUnit OBJECT-TYPE
SYNTAX Adsl2Unit SYNTAX Adsl2Unit
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The termination unit ATUC{1} or ATUR{2}." "The termination unit atuc(1) or atur(2)."
::= { adsl2LineInventoryEntry 1 } ::= { adsl2LineInventoryEntry 1 }
adsl2LInvG994VendorId OBJECT-TYPE adsl2LInvG994VendorId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(8)) SYNTAX OCTET STRING (SIZE(8))
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The ATU G.994.1 Vendor ID as inserted in the G.994.1 CL/CLR "The ATU G.994.1 Vendor ID as inserted in the G.994.1 CL/CLR
message. It consists of 8 binary octets, including a country message. It consists of 8 binary octets, including a country
code followed by a (regionally allocated) provider code, as code followed by a (regionally allocated) provider code, as
skipping to change at page 69, line 16 skipping to change at page 69, line 27
adsl2LInvSystemVendorId OBJECT-TYPE adsl2LInvSystemVendorId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(8)) SYNTAX OCTET STRING (SIZE(8))
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The ATU System Vendor ID (identifies the ATU system "The ATU System Vendor ID (identifies the ATU system
integrator) as inserted in the Overhead Messages (both ATUs integrator) as inserted in the Overhead Messages (both ATUs
for G.992.3 and G.992.4) or in the Embedded Operations for G.992.3 and G.992.4) or in the Embedded Operations
Channel (only ATU-R in G.992.1 and G.992.2). It consists of Channel (only ATU-R in G.992.1 and G.992.2). It consists of
8 binary octets, with same format as used for 8 binary octets, with the same format as used for
Adsl2InvG994VendorId." Adsl2InvG994VendorId."
REFERENCE "ITU-T G.997.1, paragraph 7.4" REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 3 } ::= { adsl2LineInventoryEntry 3 }
adsl2LInvVersionNumber OBJECT-TYPE adsl2LInvVersionNumber OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..16)) SYNTAX OCTET STRING (SIZE(0..16))
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The ATU version number (vendor specific information) as "The ATU version number (vendor-specific information) as
inserted in the Overhead Messages (both ATUs for G.992.3 and inserted in the Overhead Messages (both ATUs for G.992.3 and
G.992.4) or in the Embedded Operations Channel (only ATU-R in G.992.4) or in the Embedded Operations Channel (only ATU-R in
G.992.1 and G.992.2). It consists of up to 16 binary octets." G.992.1 and G.992.2). It consists of up to 16 binary octets."
REFERENCE "ITU-T G.997.1, paragraph 7.4" REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 4 } ::= { adsl2LineInventoryEntry 4 }
adsl2LInvSerialNumber OBJECT-TYPE adsl2LInvSerialNumber OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0..32)) SYNTAX OCTET STRING (SIZE(0..32))
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The ATU serial number (vendor specific information) as "The ATU serial number (vendor-specific information) as
inserted in the Overhead Messages (both ATUs for G.992.3 and inserted in the Overhead Messages (both ATUs for G.992.3 and
G.992.4) or in the Embedded Operations Channel (only ATU-R in G.992.4) or in the Embedded Operations Channel (only ATU-R in
G.992.1 and G.992.2). It is vendor specific information. It G.992.1 and G.992.2). It is vendor-specific information. It
consists of up to 32 ASCII characters." consists of up to 32 ASCII characters."
REFERENCE "ITU-T G.997.1, paragraph 7.4" REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 5 } ::= { adsl2LineInventoryEntry 5 }
adsl2LInvSelfTestResult OBJECT-TYPE adsl2LInvSelfTestResult OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The ATU self-test result, coded as a 32-bit value. The "The ATU self-test result, coded as a 32-bit value. The
skipping to change at page 70, line 33 skipping to change at page 70, line 44
------------------------------------------------ ------------------------------------------------
-- adsl2LineConfTemplateTable -- -- adsl2LineConfTemplateTable --
------------------------------------------------ ------------------------------------------------
adsl2LineConfTemplateTable OBJECT-TYPE adsl2LineConfTemplateTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineConfTemplateEntry SYNTAX SEQUENCE OF Adsl2LineConfTemplateEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2LineConfTemplateTable contains ADSL2 line "The table adsl2LineConfTemplateTable contains ADSL2 line
configuration template. configuration templates.
Entries in this table MUST be maintained in a Entries in this table MUST be maintained in a
persistent manner." persistent manner."
::= { adsl2ProfileLine 1 } ::= { adsl2ProfileLine 1 }
adsl2LineConfTemplateEntry OBJECT-TYPE adsl2LineConfTemplateEntry OBJECT-TYPE
SYNTAX Adsl2LineConfTemplateEntry SYNTAX Adsl2LineConfTemplateEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2LineConfTemplateTable contains ADSL2 line "The table adsl2LineConfTemplateTable contains the ADSL2 line
configuration template. configuration template.
A default template with an index of 'DEFVAL' will A default template with an index of 'DEFVAL' will
always exist and its parameters will be set to vendor-specific always exist, and its parameters will be set to vendor-
values, unless otherwise specified in this document" specific values, unless otherwise specified in this document."
INDEX { adsl2LConfTempTemplateName } INDEX { adsl2LConfTempTemplateName }
::= { adsl2LineConfTemplateTable 1 } ::= { adsl2LineConfTemplateTable 1 }
Adsl2LineConfTemplateEntry ::= Adsl2LineConfTemplateEntry ::=
SEQUENCE { SEQUENCE {
adsl2LConfTempTemplateName SnmpAdminString, adsl2LConfTempTemplateName SnmpAdminString,
adsl2LConfTempLineProfile SnmpAdminString, adsl2LConfTempLineProfile SnmpAdminString,
adsl2LConfTempChan1ConfProfile SnmpAdminString, adsl2LConfTempChan1ConfProfile SnmpAdminString,
adsl2LConfTempChan1RaRatioDs Unsigned32, adsl2LConfTempChan1RaRatioDs Unsigned32,
adsl2LConfTempChan1RaRatioUs Unsigned32, adsl2LConfTempChan1RaRatioUs Unsigned32,
adsl2LConfTempChan2ConfProfile SnmpAdminString, adsl2LConfTempChan2ConfProfile SnmpAdminString,
adsl2LConfTempChan2RaRatioDs Unsigned32, adsl2LConfTempChan2RaRatioDs Unsigned32,
adsl2LConfTempChan2RaRatioUs Unsigned32, adsl2LConfTempChan2RaRatioUs Unsigned32,
skipping to change at page 71, line 38 skipping to change at page 71, line 50
"This object identifies a row in this table." "This object identifies a row in this table."
REFERENCE "DSL Forum TR-90, paragraph 5.1.4" REFERENCE "DSL Forum TR-90, paragraph 5.1.4"
::= { adsl2LineConfTemplateEntry 1 } ::= { adsl2LineConfTemplateEntry 1 }
adsl2LConfTempLineProfile OBJECT-TYPE adsl2LConfTempLineProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32)) SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The value of this object identifies the row in the ADSL2 Line "The value of this object identifies the row in the ADSL2 Line
Configuration Profile Table, (Adsl2LineConfProfileTable), Configuration Profile Table, (adsl2LineConfProfTable),
which applies for this ADSL2 line." which applies for this ADSL2 line."
REFERENCE "DSL Forum TR-90, paragraph 5.1.4" REFERENCE "DSL Forum TR-90, paragraph 5.1.4"
DEFVAL { "DEFVAL" } DEFVAL { "DEFVAL" }
::= { adsl2LineConfTemplateEntry 2 } ::= { adsl2LineConfTemplateEntry 2 }
adsl2LConfTempChan1ConfProfile OBJECT-TYPE adsl2LConfTempChan1ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32)) SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The value of this object identifies the row in the ADSL2 "The value of this object identifies the row in the ADSL2
Channel Configuration Profile Table, Channel Configuration Profile Table,
(Adsl2ChanConfProfileTable) that applies to ADSL2 bearer (adsl2ChConfProfileTable) that applies to ADSL2 bearer
channel #1. The channel profile name specified here must channel #1. The channel profile name specified here must
match the name of an existing row in the match the name of an existing row in the
adsl2ChConfProfileTable table." adsl2ChConfProfileTable table."
DEFVAL { "DEFVAL" } DEFVAL { "DEFVAL" }
::= { adsl2LineConfTemplateEntry 3 } ::= { adsl2LineConfTemplateEntry 3 }
adsl2LConfTempChan1RaRatioDs OBJECT-TYPE adsl2LConfTempChan1RaRatioDs OBJECT-TYPE
SYNTAX Unsigned32(0..100) SYNTAX Unsigned32(0..100)
UNITS "percents" UNITS "percent"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken "Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #1 when performing rate into account for the bearer channel #1 when performing rate
adaptation on Downstream. The ratio refers to the available adaptation on Downstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the 100 - bearer channels. Also, the 100 -
Adsl2ConfTemplateChan1RaRatioDs is the ratio of excess data adsl2LConfTempChan1RaRatioDs is the ratio of excess data
rate to be assigned to all other bearer channels on Downstream rate to be assigned to all other bearer channels on Downstream
direction. The sum of rate adaptation ratios over all bearers direction. The sum of rate adaptation ratios over all bearers
on the same direction shall be equal to 100%." on the same direction shall be equal to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 100 } DEFVAL { 100 }
::= { adsl2LineConfTemplateEntry 4 } ::= { adsl2LineConfTemplateEntry 4 }
adsl2LConfTempChan1RaRatioUs OBJECT-TYPE adsl2LConfTempChan1RaRatioUs OBJECT-TYPE
SYNTAX Unsigned32(0..100) SYNTAX Unsigned32(0..100)
UNITS "percents" UNITS "percent"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken "Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #1 when performing rate into account for the bearer channel #1 when performing rate
adaptation on Upstream. The ratio refers to the available adaptation on Upstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the bearer channels. Also, the
100 - Adsl2ConfTemplateChan1RaRatioUs is the ratio of excess 100 - adsl2LConfTempChan1RaRatioUs is the ratio of excess
data rate to be assigned to all other bearer channels on data rate to be assigned to all other bearer channels on
Upstream direction. The sum of rate adaptation ratios over Upstream direction. The sum of rate adaptation ratios over
all bearers on the same direction shall be equal to 100 %." all bearers on the same direction shall be equal to 100 %."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 100 } DEFVAL { 100 }
::= { adsl2LineConfTemplateEntry 5 } ::= { adsl2LineConfTemplateEntry 5 }
adsl2LConfTempChan2ConfProfile OBJECT-TYPE adsl2LConfTempChan2ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32)) SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The value of this object identifies the row in the ADSL2 "The value of this object identifies the row in the ADSL2
Channel Configuration Profile Table, Channel Configuration Profile Table
(Adsl2ChanConfProfileTable) that applies to ADSL2 bearer (adsl2ChConfProfileTable) that applies to ADSL2 bearer
channel #2. If the channel is unused, then the object is set channel #2. If the channel is unused, then the object is set
to a zero length string. to a zero-length string.
This object may be set to a zero length string only if This object may be set to a zero-length string only if
adsl2LConfTempChan3ConfProfile contains a zero length adsl2LConfTempChan3ConfProfile contains a zero-length
string." string."
DEFVAL { "" } DEFVAL { "" }
::= { adsl2LineConfTemplateEntry 6 } ::= { adsl2LineConfTemplateEntry 6 }
adsl2LConfTempChan2RaRatioDs OBJECT-TYPE adsl2LConfTempChan2RaRatioDs OBJECT-TYPE
SYNTAX Unsigned32(0..100) SYNTAX Unsigned32(0..100)
UNITS "percents" UNITS "percent"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken "Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #2 when performing rate into account for the bearer channel #2 when performing rate
adaptation on Downstream. The ratio refers to the available adaptation on Downstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the bearer channels. Also, the
100 - Adsl2ConfTemplateChan2RaRatioDs is the ratio of excess 100 - adsl2LConfTempChan2RaRatioDs is the ratio of excess
data rate to be assigned to all other bearer channels on data rate to be assigned to all other bearer channels on
Downstream direction. The sum of rate adaptation ratios Downstream direction. The sum of rate adaptation ratios
over all bearers on the same direction shall be equal to over all bearers on the same direction shall be equal to
100%." 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 7 } ::= { adsl2LineConfTemplateEntry 7 }
adsl2LConfTempChan2RaRatioUs OBJECT-TYPE adsl2LConfTempChan2RaRatioUs OBJECT-TYPE
SYNTAX Unsigned32(0..100) SYNTAX Unsigned32(0..100)
UNITS "percents" UNITS "percent"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken "Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #2 when performing rate into account for the bearer channel #2 when performing rate
adaptation on Upstream. The ratio refers to the available adaptation on Upstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the bearer channels. Also, the
100 - Adsl2ConfTemplateChan2RaRatioUs is the ratio of excess 100 - adsl2LConfTempChan2RaRatioUs is the ratio of excess
data rate to be assigned to all other bearer channels on data rate to be assigned to all other bearer channels on
Upstream direction. The sum of rate adaptation ratios over Upstream direction. The sum of rate adaptation ratios over
all bearers on the same direction shall be equal to 100 %." all bearers on the same direction shall be equal to 100 %."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 8 } ::= { adsl2LineConfTemplateEntry 8 }
adsl2LConfTempChan3ConfProfile OBJECT-TYPE adsl2LConfTempChan3ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32)) SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The value of this object identifies the row in the ADSL2 "The value of this object identifies the row in the ADSL2
Channel Configuration Profile Table, Channel Configuration Profile Table
(Adsl2ChanConfProfileTable) that applies to ADSL2 bearer (adsl2ChConfProfileTable) that applies to ADSL2 bearer
channel #3. If the channel is unused, then the object is set channel #3. If the channel is unused, then the object is set
to a zero length string. to a zero-length string.
This object may be set to a zero length string only if This object may be set to a zero-length string only if
adsl2LConfTempChan4ConfProfile contains a zero length adsl2LConfTempChan4ConfProfile contains a zero-length
string. string.
This object may be set to a non-zero length string only if This object may be set to a non-zero-length string only if
adsl2LConfTempChan2ConfProfile contains a non-zero length adsl2LConfTempChan2ConfProfile contains a non-zero-length
string." string."
DEFVAL { "" } DEFVAL { "" }
::= { adsl2LineConfTemplateEntry 9 } ::= { adsl2LineConfTemplateEntry 9 }
adsl2LConfTempChan3RaRatioDs OBJECT-TYPE adsl2LConfTempChan3RaRatioDs OBJECT-TYPE
SYNTAX Unsigned32(0..100) SYNTAX Unsigned32(0..100)
UNITS "percents" UNITS "percent"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken "Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #3 when performing rate into account for the bearer channel #3 when performing rate
adaptation on Downstream. The ratio refers to the available adaptation on Downstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the 100 - bearer channels. Also, the 100 -
Adsl2ConfTemplateChan3RaRatioDs is the ratio of excess data adsl2LConfTempChan3RaRatioDs is the ratio of excess data
rate to be assigned to all other bearer channels on Downstream rate to be assigned to all other bearer channels on Downstream
direction. The sum of rate adaptation ratios over all bearers direction. The sum of rate adaptation ratios over all bearers
on the same direction shall be equal to 100%." on the same direction shall be equal to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 10 } ::= { adsl2LineConfTemplateEntry 10 }
adsl2LConfTempChan3RaRatioUs OBJECT-TYPE adsl2LConfTempChan3RaRatioUs OBJECT-TYPE
SYNTAX Unsigned32(0..100) SYNTAX Unsigned32(0..100)
UNITS "percents" UNITS "percent"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken "Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #3 when performing rate into account for the bearer channel #3 when performing rate
adaptation on Upstream. The ratio refers to the available adaptation on Upstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the bearer channels. Also, the
100 - Adsl2ConfTemplateChan3RaRatioUs is the ratio of excess 100 - adsl2LConfTempChan3RaRatioUs is the ratio of excess
data rate to be assigned to all other bearer channels on data rate to be assigned to all other bearer channels on
Upstream direction. The sum of rate adaptation ratios over Upstream direction. The sum of rate adaptation ratios over
all bearers on the same direction shall be equal to 100%." all bearers on the same direction shall be equal to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 11 } ::= { adsl2LineConfTemplateEntry 11 }
adsl2LConfTempChan4ConfProfile OBJECT-TYPE adsl2LConfTempChan4ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32)) SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The value of this object identifies the row in the ADSL2 "The value of this object identifies the row in the ADSL2
Channel Configuration Profile Table Channel Configuration Profile Table
(Adsl2ChanConfProfileTableDs) that applies to ADSL2 bearer (adsl2ChConfProfileTable) that applies to ADSL2 bearer
channel #4. If the channel is unused, then the object is set channel #4. If the channel is unused, then the object is set
to a zero length string. to a zero-length string.
This object may be set to a non-zero length string only if This object may be set to a non-zero-length string only if
adsl2LConfTempChan3ConfProfile contains a non-zero length adsl2LConfTempChan3ConfProfile contains a non-zero-length
string." string."
DEFVAL { "" } DEFVAL { "" }
::= { adsl2LineConfTemplateEntry 12 } ::= { adsl2LineConfTemplateEntry 12 }
adsl2LConfTempChan4RaRatioDs OBJECT-TYPE adsl2LConfTempChan4RaRatioDs OBJECT-TYPE
SYNTAX Unsigned32(0..100) SYNTAX Unsigned32(0..100)
UNITS "percents" UNITS "percent"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken "Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #4 when performing rate into account for the bearer channel #4 when performing rate
adaptation on Downstream. The ratio refers to the available adaptation on Downstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the 100 - bearer channels. Also, the 100 -
adsl2LConfTempChan4RaRatioDs is the ratio of adsl2LConfTempChan4RaRatioDs is the ratio of
excess data rate to be assigned to all other bearer channels. excess data rate to be assigned to all other bearer channels.
The sum of rate adaptation ratios over all bearers on the same The sum of rate adaptation ratios over all bearers on the same
direction shall sum to 100%." direction shall sum to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 13 } ::= { adsl2LineConfTemplateEntry 13 }
adsl2LConfTempChan4RaRatioUs OBJECT-TYPE adsl2LConfTempChan4RaRatioUs OBJECT-TYPE
SYNTAX Unsigned32(0..100) SYNTAX Unsigned32(0..100)
UNITS "percents" UNITS "percent"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken "Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #4 when performing rate into account for the bearer channel #4 when performing rate
adaptation on Upstream. The ratio refers to the available adaptation on Upstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over data rate in excess of the Minimum Data Rate, summed over
all bearer channels. Also, the 100 - all bearer channels. Also, the 100 -
adsl2LConfTempChan4RaRatioUs is the adsl2LConfTempChan4RaRatioUs is the
ratio of excess data rate to be assigned to all other bearer ratio of excess data rate to be assigned to all other bearer
channels. The sum of rate adaptation ratios over all bearers channels. The sum of rate adaptation ratios over all bearers
on the same direction shall sum to 100%." on the same direction shall sum to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 14 } ::= { adsl2LineConfTemplateEntry 14 }
adsl2LConfTempRowStatus OBJECT-TYPE adsl2LConfTempRowStatus OBJECT-TYPE
SYNTAX RowStatus SYNTAX RowStatus
skipping to change at page 76, line 37 skipping to change at page 76, line 48
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is used to create a new row or to modify or "This object is used to create a new row or to modify or
delete an existing row in this table. delete an existing row in this table.
A template is activated by setting this object to 'active'. A template is activated by setting this object to 'active'.
When 'active' is set, the system will validate the template. When 'active' is set, the system will validate the template.
Before a template can be deleted or taken out of service Before a template can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'), (by setting this object to 'destroy' or 'notInService'),
it must be first unreferenced from all associated it must first be unreferenced from all associated
lines." lines."
::= { adsl2LineConfTemplateEntry 15 } ::= { adsl2LineConfTemplateEntry 15 }
------------------------------------------ ------------------------------------------
-- adsl2LineConfProfTable -- -- adsl2LineConfProfTable --
------------------------------------------ ------------------------------------------
adsl2LineConfProfTable OBJECT-TYPE adsl2LineConfProfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineConfProfEntry SYNTAX SEQUENCE OF Adsl2LineConfProfEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2LineConfProfTable contains ADSL2 line profile "The table adsl2LineConfProfTable contains ADSL2 line profile
configuration. configuration.
skipping to change at page 77, line 18 skipping to change at page 77, line 28
adsl2LineConfProfEntry OBJECT-TYPE adsl2LineConfProfEntry OBJECT-TYPE
SYNTAX Adsl2LineConfProfEntry SYNTAX Adsl2LineConfProfEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2LineConfProfTable contains ADSL2 line profile "The table adsl2LineConfProfTable contains ADSL2 line profile
configuration. configuration.
A default profile with an index of 'DEFVAL' will A default profile with an index of 'DEFVAL' will
always exist and its parameters will be set to vendor-specific always exist, and its parameters will be set to vendor-
values, unless otherwise specified in this document" specific values, unless otherwise specified in this document."
INDEX { adsl2LConfProfProfileName } INDEX { adsl2LConfProfProfileName }
::= { adsl2LineConfProfTable 1 } ::= { adsl2LineConfProfTable 1 }
Adsl2LineConfProfEntry ::= Adsl2LineConfProfEntry ::=
SEQUENCE { SEQUENCE {
adsl2LConfProfProfileName SnmpAdminString, adsl2LConfProfProfileName SnmpAdminString,
adsl2LConfProfScMaskDs Adsl2ScMaskDs, adsl2LConfProfScMaskDs Adsl2ScMaskDs,
adsl2LConfProfScMaskUs Adsl2ScMaskUs, adsl2LConfProfScMaskUs Adsl2ScMaskUs,
adsl2LConfProfRfiBandsDs Adsl2RfiDs, adsl2LConfProfRfiBandsDs Adsl2RfiDs,
adsl2LConfProfRaModeDs Adsl2RaMode, adsl2LConfProfRaModeDs Adsl2RaMode,
skipping to change at page 79, line 13 skipping to change at page 79, line 24
DESCRIPTION DESCRIPTION
"The subset of downstream PSD mask breakpoints that shall be "The subset of downstream PSD mask breakpoints that shall be
used to notch an RFI band. used to notch an RFI band.
The specific interpolation around these points is defined in The specific interpolation around these points is defined in
G.992.5. It is a bitmap of 512 bits that allows referring to G.992.5. It is a bitmap of 512 bits that allows referring to
up to 512 downstream sub-carriers, depending on NSCds. If bit up to 512 downstream sub-carriers, depending on NSCds. If bit
i (0 <= i < NSCds) is set to '1', the respective downstream i (0 <= i < NSCds) is set to '1', the respective downstream
sub-carrier i is part of a notch filter, and if set to '0', sub-carrier i is part of a notch filter, and if set to '0',
the respective sub-carrier is not part of a notch filter. the respective sub-carrier is not part of a notch filter.
This information complements the specification provided by This information complements the specification provided by
adsl2LconfProfPsdMaskDs. adsl2LConfProfPsdMaskDs.
Note that if NSCds < 512, all bits i (NSCds<i<512) Note that if NSCds < 512, all bits i (NSCds<i<512)
should be set to '0'. " should be set to '0'. "
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2.9" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2.9"
::= { adsl2LineConfProfEntry 4 } ::= { adsl2LineConfProfEntry 4 }
adsl2LConfProfRaModeDs OBJECT-TYPE adsl2LConfProfRaModeDs OBJECT-TYPE
SYNTAX Adsl2RaMode SYNTAX Adsl2RaMode
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The mode of operation of a rate-adaptive ATU-C in the transmit "The mode of operation of a rate-adaptive ATU-C in the transmit
direction. The parameter can take three values: direction. The parameter can take three values:
manual (1), manual (1),
raInit (2), raInit(2), or
dynamicRa (3)." dynamicRa (3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.1"
DEFVAL { manual } DEFVAL { manual }
::= { adsl2LineConfProfEntry 5 } ::= { adsl2LineConfProfEntry 5 }
adsl2LConfProfRaModeUs OBJECT-TYPE adsl2LConfProfRaModeUs OBJECT-TYPE
SYNTAX Adsl2RaMode SYNTAX Adsl2RaMode
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The mode of operation of a rate-adaptive ATU-R in the transmit "The mode of operation of a rate-adaptive ATU-R in the transmit
direction. The parameter can take three values: direction. The parameter can take three values:
manual (1), manual (1),
raInit (2), raInit(2), or
dynamicRa (3)." dynamicRa (3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.2" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.2"
DEFVAL { manual } DEFVAL { manual }
::= { adsl2LineConfProfEntry 6 } ::= { adsl2LineConfProfEntry 6 }
adsl2LConfProfRaUsNrmDs OBJECT-TYPE adsl2LConfProfRaUsNrmDs OBJECT-TYPE
SYNTAX Unsigned32(0..310) SYNTAX Unsigned32(0..310)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The Downstream Up-Shift Noise Margin value, to be used when "The Downstream Up-Shift Noise Margin value, to be used when
Adsl2LineConfRaModeDs is set to dynamicRa. If the downstream adsl2LConfProfRaModeDs is set to dynamicRa. If the downstream
noise margin is above this value and stays above it for noise margin is above this value and stays above it for
more than the time specified by the Adsl2LineConfRaUsTimeDs, more than the time specified by the adsl2LConfProfRaUsTimeDs,
the ATU-R shall attempt to increase the downstream net data the ATU-R shall attempt to increase the downstream net data
rate. The Downstream Up-shift Noise Margin ranges from 0 to rate. The Downstream Up-Shift Noise Margin ranges from 0 to
310 units of 0.1 dB (Physical values are 0 to 31 dB)." 310 units of 0.1 dB (physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.3" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.3"
DEFVAL { 10 } DEFVAL { 10 }
::= { adsl2LineConfProfEntry 7 } ::= { adsl2LineConfProfEntry 7 }
adsl2LConfProfRaUsNrmUs OBJECT-TYPE adsl2LConfProfRaUsNrmUs OBJECT-TYPE
SYNTAX Unsigned32(0..310) SYNTAX Unsigned32(0..310)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The Upstream Up-Shift Noise Margin value, to be used when "The Upstream Up-Shift Noise Margin value, to be used when
Adsl2LineConfRaModeUs is set to dynamicRa. If the upstream adsl2LConfProfRaModeUs is set to dynamicRa. If the upstream
noise margin is above this value and stays above it for more noise margin is above this value and stays above it for more
than the time specified by the Adsl2LineConfRaUsTimeUs, the than the time specified by the adsl2LConfProfRaUsTimeUs, the
ATU-C shall attempt to increase the upstream net data rate. ATU-C shall attempt to increase the upstream net data rate.
The Upstream Up-shift Noise Margin ranges from 0 to 310 units The Upstream Up-Shift Noise Margin ranges from 0 to 310 units
of 0.1 dB (Physical values are 0 to 31 dB)." of 0.1 dB (physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.4" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.4"
DEFVAL { 10 } DEFVAL { 10 }
::= { adsl2LineConfProfEntry 8 } ::= { adsl2LineConfProfEntry 8 }
adsl2LConfProfRaUsTimeDs OBJECT-TYPE adsl2LConfProfRaUsTimeDs OBJECT-TYPE
SYNTAX Unsigned32(0..16383) SYNTAX Unsigned32(0..16383)
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The Downstream Up-Shift Time Interval, to be used when "The Downstream Up-Shift Time Interval, to be used when
Adsl2LineConfRaModeDs is set to dynamicRa. The interval of adsl2LConfProfRaModeDs is set to dynamicRa. The interval of
time that the downstream noise margin should stay above the time that the downstream noise margin should stay above the
Downstream Up-shift Noise Margin before the ATU-R shall Downstream Up-Shift Noise Margin before the ATU-R shall
attempt to increase the downstream net data rate. The time attempt to increase the downstream net data rate. The time
interval ranges from 0 to 16383 seconds." interval ranges from 0 to 16383 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.5" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.5"
DEFVAL { 3600 } DEFVAL { 3600 }
::= { adsl2LineConfProfEntry 9 } ::= { adsl2LineConfProfEntry 9 }
adsl2LConfProfRaUsTimeUs OBJECT-TYPE adsl2LConfProfRaUsTimeUs OBJECT-TYPE
SYNTAX Unsigned32(0..16383) SYNTAX Unsigned32(0..16383)
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The Upstream Up-Shift Time Interval, to be used when "The Upstream Up-Shift Time Interval, to be used when
Adsl2LineConfRaModeUs is set to dynamicRa. The interval of adsl2LConfProfRaModeUs is set to dynamicRa. The interval of
time the upstream noise margin should stay above the time the upstream noise margin should stay above the
Upstream Up-shift Noise Margin before the ATU-C shall Upstream Up-Shift Noise Margin before the ATU-C shall
attempt to increase the upstream net data rate. The time attempt to increase the upstream net data rate. The time
interval ranges from 0 to 16383 seconds." interval ranges from 0 to 16383 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.6" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.6"
DEFVAL { 3600 } DEFVAL { 3600 }
::= { adsl2LineConfProfEntry 10 } ::= { adsl2LineConfProfEntry 10 }
adsl2LConfProfRaDsNrmsDs OBJECT-TYPE adsl2LConfProfRaDsNrmsDs OBJECT-TYPE
SYNTAX Unsigned32(0..310) SYNTAX Unsigned32(0..310)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The Downstream Down-Shift Noise Margin value, to be used when "The Downstream Down-Shift Noise Margin value, to be used when
Adsl2LineConfRaModeDs is set to dynamicRa. If the downstream adsl2LConfProfRaModeDs is set to dynamicRa. If the downstream
noise margin is below this value and stays below that for more noise margin is below this value and stays below that for more
than the time specified by the Adsl2LineConfRaDsTimeDs, the than the time specified by the adsl2LConfProfRaDsTimeDs, the
ATU-R shall attempt to decrease the downstream net data rate. ATU-R shall attempt to decrease the downstream net data rate.
The Downstream Down-shift Noise Margin ranges from 0 to 310 The Downstream Down-Shift Noise Margin ranges from 0 to 310
units of 0.1 dB (Physical values are 0 to 31 dB)." units of 0.1 dB (physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.7" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.7"
DEFVAL { 10 } DEFVAL { 10 }
::= { adsl2LineConfProfEntry 11 } ::= { adsl2LineConfProfEntry 11 }
adsl2LConfProfRaDsNrmsUs OBJECT-TYPE adsl2LConfProfRaDsNrmsUs OBJECT-TYPE
SYNTAX Unsigned32(0..310) SYNTAX Unsigned32(0..310)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The Upstream Downshift Noise Margin value, to be used when "The Upstream Down-Shift Noise Margin value, to be used when
Adsl2LineConfRaModeUs is set to dynamicRa. If the upstream adsl2LConfProfRaModeUs is set to dynamicRa. If the upstream
noise margin is below this value and stays below that for more noise margin is below this value and stays below that for more
than the time specified by the Adsl2LineConfRaDsTimeUs, the than the time specified by the adsl2LConfProfRaDsTimeUs, the
ATU-C shall attempt to decrease the upstream net data rate. ATU-C shall attempt to decrease the upstream net data rate.
The Upstream Down-shift Noise Margin ranges from 0 to 310 The Upstream Down-Shift Noise Margin ranges from 0 to 310
units of 0.1 dB (Physical values are 0 to 31 dB)." units of 0.1 dB (physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.8" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.8"
DEFVAL { 10 } DEFVAL { 10 }
::= { adsl2LineConfProfEntry 12 } ::= { adsl2LineConfProfEntry 12 }
adsl2LConfProfRaDsTimeDs OBJECT-TYPE adsl2LConfProfRaDsTimeDs OBJECT-TYPE
SYNTAX Unsigned32(0..16383) SYNTAX Unsigned32(0..16383)
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The Downstream Downshift Time Interval, to be used when "The Downstream Down-Shift Time Interval, to be used when
Adsl2LineConfRaModeDs is set to dynamicRa. The interval of adsl2LConfProfRaModeDs is set to dynamicRa. The interval of
time the downstream noise margin should stay below the time the downstream noise margin should stay below the
Downstream Down-shift Noise Margin before the ATU-R shall Downstream Down-Shift Noise Margin before the ATU-R shall
attempt to decrease the downstream net data rate. The time attempt to decrease the downstream net data rate. The time
interval ranges from 0 to 16383 seconds." interval ranges from 0 to 16383 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.9" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.9"
DEFVAL { 3600 } DEFVAL { 3600 }
::= { adsl2LineConfProfEntry 13 } ::= { adsl2LineConfProfEntry 13 }
adsl2LConfProfRaDsTimeUs OBJECT-TYPE adsl2LConfProfRaDsTimeUs OBJECT-TYPE
SYNTAX Unsigned32(0..16383) SYNTAX Unsigned32(0..16383)
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The Upstream Down-Shift Time Interval, to be used when "The Upstream Down-Shift Time Interval, to be used when
Adsl2LineConfRaModeUs is set to dynamicRa. The interval of adsl2LConfProfRaModeUs is set to dynamicRa. The interval of
time the upstream noise margin should stay below the Upstream time the upstream noise margin should stay below the Upstream
Down-shift Noise Margin before the ATU-C shall attempt to Down-Shift Noise Margin before the ATU-C shall attempt to
decrease the upstream net data rate. The time interval ranges decrease the upstream net data rate. The time interval ranges
from 0 to 16383 seconds." from 0 to 16383 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.10" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.10"
DEFVAL { 3600 } DEFVAL { 3600 }
::= { adsl2LineConfProfEntry 14 } ::= { adsl2LineConfProfEntry 14 }
adsl2LConfProfTargetSnrmDs OBJECT-TYPE adsl2LConfProfTargetSnrmDs OBJECT-TYPE
SYNTAX Unsigned32(0..310) SYNTAX Unsigned32(0..310)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-create MAX-ACCESS read-create
skipping to change at page 82, line 42 skipping to change at page 83, line 5
DEFVAL { 3600 } DEFVAL { 3600 }
::= { adsl2LineConfProfEntry 14 } ::= { adsl2LineConfProfEntry 14 }
adsl2LConfProfTargetSnrmDs OBJECT-TYPE adsl2LConfProfTargetSnrmDs OBJECT-TYPE
SYNTAX Unsigned32(0..310) SYNTAX Unsigned32(0..310)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The minimum Noise Margin the ATU-R receiver shall achieve, "The minimum Noise Margin the ATU-R receiver shall achieve,
relative to the BER requirement for each of the downstream relative to the BER requirement for each of the downstream
bearer channels, to successfully complete initialization. bearer channels, to successfully complete initialization.
The target noise margin ranges from 0 to 310 units of 0.1 dB The target noise margin ranges from 0 to 310 units of 0.1 dB
(Physical values are 0 to 31 dB)." (physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.1"
DEFVAL { 60 } DEFVAL { 60 }
::= { adsl2LineConfProfEntry 15 } ::= { adsl2LineConfProfEntry 15 }
adsl2LConfProfTargetSnrmUs OBJECT-TYPE adsl2LConfProfTargetSnrmUs OBJECT-TYPE
SYNTAX Unsigned32(0..310) SYNTAX Unsigned32(0..310)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The minimum Noise Margin the ATU-C receiver shall achieve, "The minimum Noise Margin the ATU-C receiver shall achieve,
relative to the BER requirement for each of the upstream relative to the BER requirement for each of the upstream
bearer channels, to successfully complete initialization. bearer channels, to successfully complete initialization.
The target noise margin ranges from 0 to 310 units of 0.1 dB The target noise margin ranges from 0 to 310 units of 0.1 dB
(Physical values are 0 to 31 dB)." (physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.2" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.2"
DEFVAL { 60 } DEFVAL { 60 }
::= { adsl2LineConfProfEntry 16 } ::= { adsl2LineConfProfEntry 16 }
adsl2LConfProfMaxSnrmDs OBJECT-TYPE adsl2LConfProfMaxSnrmDs OBJECT-TYPE
SYNTAX Unsigned32 (0..310 | 2147483647) SYNTAX Unsigned32 (0..310 | 2147483647)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The maximum Noise Margin the ATU-R receiver shall try to "The maximum Noise Margin the ATU-R receiver shall try to
sustain. If the Noise Margin is above this level, the ATU-R sustain. If the Noise Margin is above this level, the ATU-R
shall request that the ATU-C reduce the ATU-C transmit power shall request that the ATU-C reduce the ATU-C transmit power
to get a noise margin below this limit (if this functionality to get a noise margin below this limit (if this functionality
is supported). The maximum noise margin ranges from 0 to 310 is supported). The maximum noise margin ranges from 0 to 310
units of 0.1 dB (Physical values are 0 to 31 dB). A value of units of 0.1 dB (physical values are 0 to 31 dB). A value of
0x7FFFFFFF (2147483647) means that there is no maximum." 0x7FFFFFFF (2147483647) means that there is no maximum."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.3" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.3"
DEFVAL { 310 } DEFVAL { 310 }
::= { adsl2LineConfProfEntry 17 } ::= { adsl2LineConfProfEntry 17 }
adsl2LConfProfMaxSnrmUs OBJECT-TYPE adsl2LConfProfMaxSnrmUs OBJECT-TYPE
SYNTAX Unsigned32 (0..310 | 2147483647) SYNTAX Unsigned32 (0..310 | 2147483647)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The maximum Noise Margin the ATU-C receiver shall try to "The maximum Noise Margin the ATU-C receiver shall try to
sustain. If the Noise Margin is above this level, the ATU-C sustain. If the Noise Margin is above this level, the ATU-C
shall request that the ATU-R reduce the ATU-R transmit power shall request that the ATU-R reduce the ATU-R transmit power
to get a noise margin below this limit (if this functionality to get a noise margin below this limit (if this functionality
is supported). The maximum noise margin ranges from 0 to 310 is supported). The maximum noise margin ranges from 0 to 310
units of 0.1 dB (Physical values are 0 to 31 dB). A value of units of 0.1 dB (physical values are 0 to 31 dB). A value of
0x7FFFFFFF (2147483647) means that there is no maximum." 0x7FFFFFFF (2147483647) means that there is no maximum."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.4" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.4"
DEFVAL { 310 } DEFVAL { 310 }
::= { adsl2LineConfProfEntry 18 } ::= { adsl2LineConfProfEntry 18 }
adsl2LConfProfMinSnrmDs OBJECT-TYPE adsl2LConfProfMinSnrmDs OBJECT-TYPE
SYNTAX Unsigned32(0..310) SYNTAX Unsigned32(0..310)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The minimum Noise Margin the ATU-R receiver shall tolerate. "The minimum Noise Margin the ATU-R receiver shall tolerate.
If the noise margin falls below this level, the ATU-R shall If the noise margin falls below this level, the ATU-R shall
request that the ATU-C increase the ATU-C transmit power. request that the ATU-C increase the ATU-C transmit power.
If an increase to ATU-C transmit power is not possible, a If an increase to ATU-C transmit power is not possible, a
loss-of-margin (LOM) defect occurs, the ATU-R shall fail and loss-of-margin (LOM) defect occurs, the ATU-R shall fail and
attempt to reinitialize and the NMS shall be notified. The attempt to reinitialize, and the NMS shall be notified. The
minimum noise margin ranges from 0 to 310 units of minimum noise margin ranges from 0 to 310 units of
0.1 dB (Physical values are 0 to 31 dB). A value of 0 means 0.1 dB (physical values are 0 to 31 dB). A value of 0 means
that there is no minimum." that there is no minimum."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.5" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.5"
DEFVAL { 10 } DEFVAL { 10 }
::= { adsl2LineConfProfEntry 19 } ::= { adsl2LineConfProfEntry 19 }
adsl2LConfProfMinSnrmUs OBJECT-TYPE adsl2LConfProfMinSnrmUs OBJECT-TYPE
SYNTAX Unsigned32(0..310) SYNTAX Unsigned32(0..310)
UNITS "0.1 dB" UNITS "0.1 dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The minimum Noise Margin the ATU-C receiver shall tolerate. "The minimum Noise Margin the ATU-C receiver shall tolerate.
If the noise margin falls below this level, the ATU-C shall If the noise margin falls below this level, the ATU-C shall
request that the ATU-R increase the ATU-R transmit power. request that the ATU-R increase the ATU-R transmit power.
If an increase of ATU-R transmit power is not possible, a If an increase of ATU-R transmit power is not possible, a
loss-of-margin (LOM) defect occurs, the ATU-C shall fail and loss-of-margin (LOM) defect occurs, the ATU-C shall fail and
attempt to re-initialize and the NMS shall be notified. The attempt to reinitialize, and the NMS shall be notified. The
minimum noise margin ranges from 0 to 310 units of minimum noise margin ranges from 0 to 310 units of
0.1 dB (Physical values are 0 to 31 dB). A value of 0 means 0.1 dB (physical values are 0 to 31 dB). A value of 0 means
that there is no minimum." that there is no minimum."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.6" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.6"
DEFVAL { 10 } DEFVAL { 10 }
::= { adsl2LineConfProfEntry 20 } ::= { adsl2LineConfProfEntry 20 }
adsl2LConfProfMsgMinUs OBJECT-TYPE adsl2LConfProfMsgMinUs OBJECT-TYPE
SYNTAX Unsigned32(4000..63000) SYNTAX Unsigned32(4000..63000)
UNITS "bits/second" UNITS "bits/second"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Minimum Overhead Rate Upstream. Defines the minimum rate of "Minimum Overhead Rate Upstream. Defines the minimum rate of
the message-based overhead that shall be maintained by the ATU the message-based overhead that shall be maintained by the ATU
in upstream direction. Expressed in bits per second and in upstream direction. Expressed in bits per second and
ranges from 4000 to 63000 bps." ranges from 4000 to 63000 bps."
skipping to change at page 85, line 49 skipping to change at page 86, line 8
adsl2LConfProfPmMode OBJECT-TYPE adsl2LConfProfPmMode OBJECT-TYPE
SYNTAX Adsl2LConfProfPmMode SYNTAX Adsl2LConfProfPmMode
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Power management state Enabling. Defines the power states the "Power management state Enabling. Defines the power states the
ATU-C or ATU-R may autonomously transition to on this line. ATU-C or ATU-R may autonomously transition to on this line.
The various bit positions are: allowTransitionsToIdle (0) and The various bit positions are: allowTransitionsToIdle (0) and
allowTransitionsToLowPower (1). A bit with a '1' value means allowTransitionsToLowPower (1). A bit with a '1' value means
that the ATU is allowed to transit into the respective state that the ATU is allowed to transit into the respective state,
and a '0' value means that the ATU is not allowed and a '0' value means that the ATU is not allowed
to transit into the respective state." to transit into the respective state."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.4" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.4"
DEFVAL { { allowTransitionsToIdle, allowTransitionsToLowPower } } DEFVAL { { allowTransitionsToIdle, allowTransitionsToLowPower } }
::= { adsl2LineConfProfEntry 24 } ::= { adsl2LineConfProfEntry 24 }
adsl2LConfProfL0Time OBJECT-TYPE adsl2LConfProfL0Time OBJECT-TYPE
SYNTAX Unsigned32 (0..255) SYNTAX Unsigned32 (0..255)
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
skipping to change at page 87, line 28 skipping to change at page 87, line 35
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is used to create a new row or to modify or "This object is used to create a new row or to modify or
delete an existing row in this table. delete an existing row in this table.
A profile is activated by setting this object to 'active'. A profile is activated by setting this object to 'active'.
When 'active' is set, the system will validate the profile. When 'active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of service Before a profile can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'), (by setting this object to 'destroy' or 'notInService'),
it must be first unreferenced from all associated it must first be unreferenced from all associated
templates." templates."
::= { adsl2LineConfProfEntry 29 } ::= { adsl2LineConfProfEntry 29 }
------------------------------------------ ------------------------------------------
-- adsl2LineConfProfModeSpecTable -- -- adsl2LineConfProfModeSpecTable --
------------------------------------------ ------------------------------------------
adsl2LineConfProfModeSpecTable OBJECT-TYPE adsl2LineConfProfModeSpecTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineConfProfModeSpecEntry SYNTAX SEQUENCE OF Adsl2LineConfProfModeSpecEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2LineConfProfModeSpecTable extends the "The table adsl2LineConfProfModeSpecTable extends the
ADSL2 line configuration profile by ADSL Mode Specific ADSL2 line configuration profile by ADSL Mode Specific
parameters. parameters.
A row in this table that has an index of A row in this table that has an index of
adsl2LconfProfAdslMode == defMode(1), is called a adsl2LConfProfAdslMode == defMode(1) is called a
'mandatory' row. 'mandatory' row.
A row in this table that has an index such that A row in this table that has an index such that
adsl2LconfProfAdslMode is not equal to defMode(1), adsl2LConfProfAdslMode is not equal to defMode(1)
is called an 'optional' row. is called an 'optional' row.
When a row in the adsl2LineConfProfTable table When a row in the adsl2LineConfProfTable table
(the parent row) is created, the SNMP agent will (the parent row) is created, the SNMP agent will
automatically create a 'mandatory' row in this table. automatically create a 'mandatory' row in this table.
When the parent row is deleted, the SNMP agent will When the parent row is deleted, the SNMP agent will
automatically delete all associated rows in this table. automatically delete all associated rows in this table.
Any attempt to delete the 'mandatory' row using the Any attempt to delete the 'mandatory' row using the
adsl2LConfProfModeSpecRowStatus attribute will be adsl2LConfProfModeSpecRowStatus attribute will be
rejected by the SNMP agent. rejected by the SNMP agent.
The manager MAY create an 'optional' row in this table The manager MAY create an 'optional' row in this table
skipping to change at page 88, line 33 skipping to change at page 88, line 40
::= { adsl2ProfileLine 3 } ::= { adsl2ProfileLine 3 }
adsl2LineConfProfModeSpecEntry OBJECT-TYPE adsl2LineConfProfModeSpecEntry OBJECT-TYPE
SYNTAX Adsl2LineConfProfModeSpecEntry SYNTAX Adsl2LineConfProfModeSpecEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2LineConfProfModeSpecTable extends the "The table adsl2LineConfProfModeSpecTable extends the
ADSL2 line configuration profile by ADSL Mode Specific ADSL2 line configuration profile by ADSL Mode Specific
parameters." parameters."
INDEX { adsl2LConfProfProfileName, adsl2LconfProfAdslMode } INDEX { adsl2LConfProfProfileName, adsl2LConfProfAdslMode }
::= { adsl2LineConfProfModeSpecTable 1 } ::= { adsl2LineConfProfModeSpecTable 1 }
Adsl2LineConfProfModeSpecEntry ::= Adsl2LineConfProfModeSpecEntry ::=
SEQUENCE { SEQUENCE {
adsl2LconfProfAdslMode Adsl2OperationModes, adsl2LConfProfAdslMode Adsl2OperationModes,
adsl2LConfProfMaxNomPsdDs Integer32, adsl2LConfProfMaxNomPsdDs Integer32,
adsl2LConfProfMaxNomPsdUs Integer32, adsl2LConfProfMaxNomPsdUs Integer32,
adsl2LConfProfMaxNomAtpDs Unsigned32, adsl2LConfProfMaxNomAtpDs Unsigned32,
adsl2LConfProfMaxNomAtpUs Unsigned32, adsl2LConfProfMaxNomAtpUs Unsigned32,
adsl2LConfProfMaxAggRxPwrUs Integer32, adsl2LConfProfMaxAggRxPwrUs Integer32,
adsl2LConfProfPsdMaskDs Adsl2PsdMaskDs, adsl2LConfProfPsdMaskDs Adsl2PsdMaskDs,
adsl2LConfProfPsdMaskUs Adsl2PsdMaskUs, adsl2LConfProfPsdMaskUs Adsl2PsdMaskUs,
adsl2LConfProfPsdMaskSelectUs Unsigned32, adsl2LConfProfPsdMaskSelectUs Unsigned32,
adsl2LConfProfModeSpecRowStatus RowStatus adsl2LConfProfModeSpecRowStatus RowStatus
} }
adsl2LconfProfAdslMode OBJECT-TYPE adsl2LConfProfAdslMode OBJECT-TYPE
SYNTAX Adsl2OperationModes SYNTAX Adsl2OperationModes
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The ADSL Mode is a way of categorizing the various ADSL "The ADSL Mode is a way of categorizing the various ADSL
transmission modes into groups, each group (ADSL Mode) shares transmission modes into groups; each group (ADSL Mode) shares
the same PSD configuration. the same PSD configuration.
There should be multiple entries in this table for a given There should be multiple entries in this table for a given
line profile in case multiple bits are set in line profile in case multiple bits are set in
adsl2LConfProfAtuTransSysEna for that profile. " adsl2LConfProfAtuTransSysEna for that profile. "
REFERENCE "DSL Forum TR-90, paragraph 5.1.8" REFERENCE "DSL Forum TR-90, paragraph 5.1.8"
::= { adsl2LineConfProfModeSpecEntry 1 } ::= { adsl2LineConfProfModeSpecEntry 1 }
adsl2LConfProfMaxNomPsdDs OBJECT-TYPE adsl2LConfProfMaxNomPsdDs OBJECT-TYPE
SYNTAX Integer32(-600..-300) SYNTAX Integer32(-600..-300)
UNITS "0.1 dBm/Hz" UNITS "0.1 dBm/Hz"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The maximum nominal transmit PSD in the downstream "The maximum nominal transmit PSD in the downstream
direction during initialization and Showtime. It ranges from direction during initialization and Showtime. It ranges from
-600 to -300 units of 0.1 dBm/Hz. (physical values are -60 to -600 to -300 units of 0.1 dBm/Hz (physical values are -60 to
-30 dBm/Hz). " -30 dBm/Hz). "
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
DEFVAL { -300 } DEFVAL { -300 }
::= { adsl2LineConfProfModeSpecEntry 2 } ::= { adsl2LineConfProfModeSpecEntry 2 }
adsl2LConfProfMaxNomPsdUs OBJECT-TYPE adsl2LConfProfMaxNomPsdUs OBJECT-TYPE
SYNTAX Integer32(-600..-300) SYNTAX Integer32(-600..-300)
UNITS "0.1 dBm/Hz" UNITS "0.1 dBm/Hz"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The maximum nominal transmit PSD in the upstream direction "The maximum nominal transmit PSD in the upstream direction
during initialization and Showtime. It ranges from -600 to during initialization and Showtime. It ranges from -600 to
-300 units of 0.1 dBm/Hz. (physical values are -60 to -300 units of 0.1 dBm/Hz (physical values are -60 to
-30 dBm/Hz). " -30 dBm/Hz). "
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
DEFVAL { -300 } DEFVAL { -300 }
::= { adsl2LineConfProfModeSpecEntry 3 } ::= { adsl2LineConfProfModeSpecEntry 3 }
adsl2LConfProfMaxNomAtpDs OBJECT-TYPE adsl2LConfProfMaxNomAtpDs OBJECT-TYPE
SYNTAX Unsigned32 (0..255) SYNTAX Unsigned32 (0..255)
UNITS "0.1 dBm" UNITS "0.1 dBm"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
skipping to change at page 90, line 48 skipping to change at page 91, line 7
DEFVAL { 255 } DEFVAL { 255 }
::= { adsl2LineConfProfModeSpecEntry 6 } ::= { adsl2LineConfProfModeSpecEntry 6 }
adsl2LConfProfPsdMaskDs OBJECT-TYPE adsl2LConfProfPsdMaskDs OBJECT-TYPE
SYNTAX Adsl2PsdMaskDs SYNTAX Adsl2PsdMaskDs
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The downstream PSD mask applicable at the U-C2 reference "The downstream PSD mask applicable at the U-C2 reference
point. point.
This parameter is used only for G.992.5 and it may impose PSD This parameter is used only for G.992.5, and it may impose PSD
restrictions (breakpoints) in addition to the Limit PSD mask restrictions (breakpoints) in addition to the Limit PSD mask
defined in G.992.5. defined in G.992.5.
This is a string of 32 pairs of values in the following This is a string of 32 pairs of values in the following
structure: structure:
Octets 0+1 - Index of 1st sub-carrier used in the context Octets 0+1 - Index of 1st sub-carrier used in the context
of a first breakpoint. of a first breakpoint.
Octet 2 - The PSD reduction for the sub-carrier indicated in Octet 2 - The PSD reduction for the sub-carrier indicated in
octets 0 and 1. octets 0 and 1.
Octets 3-5 - Same, for a 2nd breakpoint. Octets 3-5 - Same, for a 2nd breakpoint.
Octets 6-8 - Same, for a 3rd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint.
This architecture continues until octets 94-95, which are This architecture continues until octets 94-95, which are
associated with a 32nd breakpoint. associated with a 32nd breakpoint.
Each subcarrier index is an unsigned number in the range 1 and Each subcarrier index is an unsigned number in the range 1 to
NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to
255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are
in the range 0 to 190 (0 to -95dBm/Hz). in the range 0 to 190 (0 to -95dBm/Hz).
When the number of breakpoints is less than 32, all remaining When the number of breakpoints is less than 32, all remaining
octets are set to the value 0. Note that the content of this octets are set to the value 0. Note that the content of this
object should be correlated with the sub-carriers mask and with object should be correlated with the sub-carriers mask and with
the RFI setup. " the RFI setup. "
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
::= { adsl2LineConfProfModeSpecEntry 7 } ::= { adsl2LineConfProfModeSpecEntry 7 }
adsl2LConfProfPsdMaskUs OBJECT-TYPE adsl2LConfProfPsdMaskUs OBJECT-TYPE
SYNTAX Adsl2PsdMaskUs SYNTAX Adsl2PsdMaskUs
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The upstream PSD mask applicable at the U-R2 reference "The upstream PSD mask applicable at the U-R2 reference
point. point.
This parameter is used only for G.992.5 and it may impose PSD This parameter is used only for G.992.5, and it may impose PSD
restrictions (breakpoints) in addition to the Limit PSD mask restrictions (breakpoints) in addition to the Limit PSD mask
defined in G.992.5. defined in G.992.5.
This is a string of 4 pairs of values in the following This is a string of 4 pairs of values in the following
structure: structure:
Octets 0+1 - Index of 1st sub-carrier used in the context Octets 0+1 - Index of 1st sub-carrier used in the context
of a first breakpoint. of a first breakpoint.
Octet 2 - The PSD reduction for the sub-carrier indicated in Octet 2 - The PSD reduction for the sub-carrier indicated in
octets 0 and 1. octets 0 and 1.
Octets 3-5 - Same, for a 2nd breakpoint. Octets 3-5 - Same, for a 2nd breakpoint.
Octets 6-8 - Same, for a 3rd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint.
This architecture continues until octets 9-11, which are This architecture continues until octets 9-11, which are
associated with a 4th breakpoint. associated with a 4th breakpoint.
Each subcarrier index is an unsigned number in the range 1 and Each subcarrier index is an unsigned number in the range 1 to
NSCus. Each PSD reduction value is in the range 0 (0dBm/Hz) to NSCus. Each PSD reduction value is in the range 0 (0dBm/Hz) to
255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are
in the range 0 to 190 (0 to -95dBm/Hz). in the range 0 to 190 (0 to -95dBm/Hz).
When the number of breakpoints is less than 4, all remaining When the number of breakpoints is less than 4, all remaining
octets are set to the value 0. Note that the content of this octets are set to the value 0. Note that the content of this
object should be correlated with the sub-carriers mask and with object should be correlated with the sub-carriers mask and with
the RFI setup. " the RFI setup. "
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2" REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
::= { adsl2LineConfProfModeSpecEntry 8 } ::= { adsl2LineConfProfModeSpecEntry 8 }
skipping to change at page 92, line 34 skipping to change at page 92, line 41
DESCRIPTION DESCRIPTION
"This object is used to create a new row or to modify or "This object is used to create a new row or to modify or
delete an existing row in this table. delete an existing row in this table.
A profile is activated by setting this object to 'active'. A profile is activated by setting this object to 'active'.
When 'active' is set, the system will validate the profile. When 'active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of service Before a profile can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'), (by setting this object to 'destroy' or 'notInService'),
it must be first unreferenced from all associated it must first be unreferenced from all associated
templates." templates."
::= { adsl2LineConfProfModeSpecEntry 10 } ::= { adsl2LineConfProfModeSpecEntry 10 }
------------------------------------------------ ------------------------------------------------
-- adsl2ChConfProfileTable -- -- adsl2ChConfProfileTable --
------------------------------------------------ ------------------------------------------------
adsl2ChConfProfileTable OBJECT-TYPE adsl2ChConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2ChConfProfileEntry SYNTAX SEQUENCE OF Adsl2ChConfProfileEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
skipping to change at page 93, line 14 skipping to change at page 93, line 21
::= { adsl2ProfileChannel 1 } ::= { adsl2ProfileChannel 1 }
adsl2ChConfProfileEntry OBJECT-TYPE adsl2ChConfProfileEntry OBJECT-TYPE
SYNTAX Adsl2ChConfProfileEntry SYNTAX Adsl2ChConfProfileEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2ChConfProfileTable contains ADSL2 channel "The table adsl2ChConfProfileTable contains ADSL2 channel
profile configuration. profile configuration.
A default profile with an index of 'DEFVAL' will A default profile with an index of 'DEFVAL' will
always exist and its parameters will be set to vendor-specific always exist, and its parameters will be set to vendor-
values, unless otherwise specified in this document" specific values, unless otherwise specified in this document."
INDEX { adsl2ChConfProfProfileName } INDEX { adsl2ChConfProfProfileName }
::= { adsl2ChConfProfileTable 1 } ::= { adsl2ChConfProfileTable 1 }
Adsl2ChConfProfileEntry ::= Adsl2ChConfProfileEntry ::=
SEQUENCE { SEQUENCE {
adsl2ChConfProfProfileName SnmpAdminString, adsl2ChConfProfProfileName SnmpAdminString,
adsl2ChConfProfMinDataRateDs Unsigned32, adsl2ChConfProfMinDataRateDs Unsigned32,
adsl2ChConfProfMinDataRateUs Unsigned32, adsl2ChConfProfMinDataRateUs Unsigned32,
adsl2ChConfProfMinResDataRateDs Unsigned32, adsl2ChConfProfMinResDataRateDs Unsigned32,
adsl2ChConfProfMinResDataRateUs Unsigned32, adsl2ChConfProfMinResDataRateUs Unsigned32,
skipping to change at page 94, line 10 skipping to change at page 94, line 17
"This object identifies a row in this table." "This object identifies a row in this table."
::= { adsl2ChConfProfileEntry 1 } ::= { adsl2ChConfProfileEntry 1 }
adsl2ChConfProfMinDataRateDs OBJECT-TYPE adsl2ChConfProfMinDataRateDs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000) SYNTAX Unsigned32(0..200000000)
UNITS "bits/second" UNITS "bits/second"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Minimum Data Rate on Downstream direction. The minimum net "Minimum Data Rate on Downstream direction. The minimum net
data rate for the bearer channel, coded in bit/s." data rate for the bearer channel, coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 2 } ::= { adsl2ChConfProfileEntry 2 }
adsl2ChConfProfMinDataRateUs OBJECT-TYPE adsl2ChConfProfMinDataRateUs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000) SYNTAX Unsigned32(0..200000000)
UNITS "bits/second" UNITS "bits/second"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Minimum Data Rate on Upstream direction. The minimum net data "Minimum Data Rate on Upstream direction. The minimum net data
rate for the bearer channel, coded in bit/s." rate for the bearer channel, coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 3 } ::= { adsl2ChConfProfileEntry 3 }
adsl2ChConfProfMinResDataRateDs OBJECT-TYPE adsl2ChConfProfMinResDataRateDs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000) SYNTAX Unsigned32(0..200000000)
UNITS "bits/second" UNITS "bits/second"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Minimum Reserved Data Rate on Downstream direction. The "Minimum Reserved Data Rate on Downstream direction. The
minimum reserved net data rate for the bearer channel, coded minimum reserved net data rate for the bearer channel, coded
in bit/s. This parameter is used only if the Rate Adaptation in bits/second. This parameter is used only if the Rate
Mode in the direction of the bearer channel (i.e., Adaptation Mode in the direction of the bearer channel (i.e.,
Adsl2LineConfRaModeDs) is set to dynamicRa." adsl2LConfProfRaModeDs) is set to dynamicRa."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 4 } ::= { adsl2ChConfProfileEntry 4 }
adsl2ChConfProfMinResDataRateUs OBJECT-TYPE adsl2ChConfProfMinResDataRateUs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000) SYNTAX Unsigned32(0..200000000)
UNITS "bits/second" UNITS "bits/second"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Minimum Reserved Data Rate on Upstream direction. The minimum "Minimum Reserved Data Rate on Upstream direction. The minimum
reserved net data rate for the bearer channel, coded in reserved net data rate for the bearer channel, coded in
bit/s. This parameter is used only if the Rate Adaptation bits/second. This parameter is used only if the Rate
Mode in the direction of the bearer channel (i.e., Adaptation Mode in the direction of the bearer channel (i.e.,
Adsl2LineConfRaModeUs) is set to dynamicRa." adsl2LConfProfRaModeUs) is set to dynamicRa."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 5 } ::= { adsl2ChConfProfileEntry 5 }
adsl2ChConfProfMaxDataRateDs OBJECT-TYPE adsl2ChConfProfMaxDataRateDs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000) SYNTAX Unsigned32(0..200000000)
UNITS "bits/second" UNITS "bits/second"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Maximum Data Rate on Downstream direction. The maximum net "Maximum Data Rate on Downstream direction. The maximum net
data rate for the bearer channel, coded in bit/s." data rate for the bearer channel, coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 6 } ::= { adsl2ChConfProfileEntry 6 }
adsl2ChConfProfMaxDataRateUs OBJECT-TYPE adsl2ChConfProfMaxDataRateUs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000) SYNTAX Unsigned32(0..200000000)
UNITS "bits/second" UNITS "bits/second"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Maximum Data Rate on Upstream direction. The maximum net data "Maximum Data Rate on Upstream direction. The maximum net data
rate for the bearer channel, coded in bit/s." rate for the bearer channel, coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 7 } ::= { adsl2ChConfProfileEntry 7 }
adsl2ChConfProfMinDataRateLowPwrDs OBJECT-TYPE adsl2ChConfProfMinDataRateLowPwrDs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000) SYNTAX Unsigned32(0..200000000)
UNITS "bits/second" UNITS "bits/second"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Minimum Data Rate in Low Power state on Downstream direction. "Minimum Data Rate in Low Power state on Downstream direction.
The minimum net data rate for the bearer channel, coded in The minimum net data rate for the bearer channel, coded in
bit/s., during the low power state (L1 in G.992.2, L2 in bits/second, during the low power state (L1 in G.992.2, L2 in
G.992.3)." G.992.3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 8 } ::= { adsl2ChConfProfileEntry 8 }
adsl2ChConfProfMaxDelayDs OBJECT-TYPE adsl2ChConfProfMaxDelayDs OBJECT-TYPE
SYNTAX Unsigned32(0..63) SYNTAX Unsigned32(0..63)
UNITS "milliseconds" UNITS "milliseconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Maximum Interleave Delay on Downstream direction. The maximum "Maximum Interleave Delay on Downstream direction. The maximum
one-way interleaving delay introduced by the PMS-TC on one-way interleaving delay introduced by the PMS-TC on
Downstream direction. The ATUs shall choose the S (factor) Downstream direction. The ATUs shall choose the S (factor)
and D (depth) values such that the actual one-way interleaving and D (depth) values such that the actual one-way interleaving
delay (Adsl2ChanStatusActDelay) is as close as possible to, delay (adsl2ChStatusActDelay) is as close as possible to,
but less than or equal to, Adsl2ChanConfMaxDelayDs. The but less than or equal to, adsl2ChConfProfMaxDelayDs. The
delay is coded in ms, with the value 0 indicating no delay delay is coded in ms, with the value 0 indicating no delay
bound is being imposed." bound is being imposed."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.2" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.2"
::= { adsl2ChConfProfileEntry 9 } ::= { adsl2ChConfProfileEntry 9 }
adsl2ChConfProfMaxDelayUs OBJECT-TYPE adsl2ChConfProfMaxDelayUs OBJECT-TYPE
SYNTAX Unsigned32(0..63) SYNTAX Unsigned32(0..63)
UNITS "milliseconds" UNITS "milliseconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Maximum Interleave Delay on Upstream direction. The maximum "Maximum Interleave Delay on Upstream direction. The maximum
one-way interleaving delay introduced by the PMS-TC on one-way interleaving delay introduced by the PMS-TC on
Upstream direction. The ATUs shall choose the S (factor) and Upstream direction. The ATUs shall choose the S (factor) and
D (depth) values such that the actual one-way interleaving D (depth) values such that the actual one-way interleaving
delay (Adsl2ChanStatusActDelay) is as close as possible to, delay (adsl2ChStatusActDelay) is as close as possible to,
but less than or equal to, Adsl2ChanConfMaxDelayUs. The but less than or equal to, adsl2ChConfProfMaxDelayUs. The
delay is coded in ms, with the value 0 indicating no delay delay is coded in ms, with the value 0 indicating no delay
bound is being imposed." bound is being imposed."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.2" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.2"
::= { adsl2ChConfProfileEntry 10 } ::= { adsl2ChConfProfileEntry 10 }
adsl2ChConfProfMinProtectionDs OBJECT-TYPE adsl2ChConfProfMinProtectionDs OBJECT-TYPE
SYNTAX Adsl2SymbolProtection SYNTAX Adsl2SymbolProtection
UNITS "symbols" UNITS "symbols"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Minimum Impulse Noise Protection on Downstream direction. The "Minimum Impulse Noise Protection on Downstream direction. The
minimum impulse noise protection for the bearer channel, minimum impulse noise protection for the bearer channel,
expressed in symbols. The parameter can take the following expressed in symbols. The parameter can take the following
values: noProtection (i.e., INP not required), halfSymbol values: noProtection (i.e., INP not required), halfSymbol
(i.e., INP length is 1/2 symbol) and 1-16 symbols in steps (i.e., INP length is 1/2 symbol), and 1-16 symbols in steps
of 1 symbol." of 1 symbol."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.3" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.3"
DEFVAL { noProtection } DEFVAL { noProtection }
::= { adsl2ChConfProfileEntry 11 } ::= { adsl2ChConfProfileEntry 11 }
adsl2ChConfProfMinProtectionUs OBJECT-TYPE adsl2ChConfProfMinProtectionUs OBJECT-TYPE
SYNTAX Adsl2SymbolProtection SYNTAX Adsl2SymbolProtection
UNITS "symbols" UNITS "symbols"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Minimum Impulse Noise Protection on Upstream direction. The "Minimum Impulse Noise Protection on Upstream direction. The
minimum impulse noise protection for the bearer channel, minimum impulse noise protection for the bearer channel,
expressed in symbols. The parameter can take the following expressed in symbols. The parameter can take the following
values: noProtection (i.e., INP not required), halfSymbol values: noProtection (i.e., INP not required), halfSymbol
(i.e., INP length is 1/2 symbol) and 1-16 symbols in steps (i.e., INP length is 1/2 symbol), and 1-16 symbols in steps
of 1 symbol." of 1 symbol."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.3" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.3"
DEFVAL { noProtection } DEFVAL { noProtection }
::= { adsl2ChConfProfileEntry 12 } ::= { adsl2ChConfProfileEntry 12 }
adsl2ChConfProfMaxBerDs OBJECT-TYPE adsl2ChConfProfMaxBerDs OBJECT-TYPE
SYNTAX Adsl2MaxBer SYNTAX Adsl2MaxBer
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Maximum Bit Error Ratio on Downstream direction. The maximum "Maximum Bit Error Ratio on Downstream direction. The maximum
bit error ratio for the bearer channel. The parameter can bit error ratio for the bearer channel. The parameter can
take the following values (for 1E-3, 1E-5 or 1E-7): take the following values (for 1E-3, 1E-5 or 1E-7):
eminus3 (1), eminus3 (1),
eminus5 (2), eminus5(2), or
eminus7 (3)" eminus7(3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.4" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.4"
DEFVAL { eminus5 } DEFVAL { eminus5 }
::= { adsl2ChConfProfileEntry 13 } ::= { adsl2ChConfProfileEntry 13 }
adsl2ChConfProfMaxBerUs OBJECT-TYPE adsl2ChConfProfMaxBerUs OBJECT-TYPE
SYNTAX Adsl2MaxBer SYNTAX Adsl2MaxBer
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Maximum Bit Error Ratio on Upstream direction. The maximum "Maximum Bit Error Ratio on Upstream direction. The maximum
bit error ratio for the bearer channel. The parameter can bit error ratio for the bearer channel. The parameter can
take the following values (for 1E-3, 1E-5 or 1E-7): take the following values (for 1E-3, 1E-5 or 1E-7):
eminus3 (1), eminus3 (1),
eminus5 (2), eminus5(2), or
eminus7 (3)" eminus7(3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.4" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.4"
DEFVAL { eminus5 } DEFVAL { eminus5 }
::= { adsl2ChConfProfileEntry 14 } ::= { adsl2ChConfProfileEntry 14 }
adsl2ChConfProfUsDataRateDs OBJECT-TYPE adsl2ChConfProfUsDataRateDs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000) SYNTAX Unsigned32(0..200000000)
UNITS "bits/second" UNITS "bits/second"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Data Rate Threshold Up shift for downstream direction. An "Data Rate Threshold Up shift for downstream direction. An
'Up-shift rate change' event is triggered when the actual 'Up-shift rate change' event is triggered when the actual
downstream data rate exceeds, by more than the threshold, the downstream data rate exceeds, by more than the threshold, the
data rate at the last entry into Showtime. The parameter is data rate at the last entry into Showtime. The parameter is
coded in bit/s." coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6"
::= { adsl2ChConfProfileEntry 15 } ::= { adsl2ChConfProfileEntry 15 }
adsl2ChConfProfDsDataRateDs OBJECT-TYPE adsl2ChConfProfDsDataRateDs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000) SYNTAX Unsigned32(0..200000000)
UNITS "bits/second" UNITS "bits/second"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Data Rate Threshold Downshift for downstream direction. A "Data Rate Threshold Down-shift for downstream direction. A
'Down-shift rate change' event is triggered when the actual 'Down-shift rate change' event is triggered when the actual
downstream data rate is below the data rate at the last entry downstream data rate is below the data rate at the last entry
into Showtime, by more than the threshold. The parameter is into Showtime, by more than the threshold. The parameter is
coded in bit/s." coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6"
::= { adsl2ChConfProfileEntry 16 } ::= { adsl2ChConfProfileEntry 16 }
adsl2ChConfProfUsDataRateUs OBJECT-TYPE adsl2ChConfProfUsDataRateUs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000) SYNTAX Unsigned32(0..200000000)
UNITS "bits/second" UNITS "bits/second"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Data Rate Threshold Up shift for upstream direction. An "Data Rate Threshold Up shift for upstream direction. An
'Up-shift rate change' event is triggered when the actual 'Up-shift rate change' event is triggered when the actual
upstream data rate exceeds, by more than the threshold, the upstream data rate exceeds, by more than the threshold, the
data rate at the last entry into Showtime. The parameter is data rate at the last entry into Showtime. The parameter is
coded in bit/s." coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6"
::= { adsl2ChConfProfileEntry 17 } ::= { adsl2ChConfProfileEntry 17 }
adsl2ChConfProfDsDataRateUs OBJECT-TYPE adsl2ChConfProfDsDataRateUs OBJECT-TYPE
SYNTAX Unsigned32(0..200000000) SYNTAX Unsigned32(0..200000000)
UNITS "bits/second" UNITS "bits/second"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Data Rate Threshold Downshift for upstream direction. A "Data Rate Threshold Down-shift for upstream direction. A
'Down-shift rate change' event is triggered when the actual 'Down-shift rate change' event is triggered when the actual
upstream data rate is below the data rate at the last entry upstream data rate is below the data rate at the last entry
into Showtime, by more than the threshold. The parameter is into Showtime, by more than the threshold. The parameter is
coded in bit/s." coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6" REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6"
::= { adsl2ChConfProfileEntry 18 } ::= { adsl2ChConfProfileEntry 18 }
adsl2ChConfProfImaEnabled OBJECT-TYPE adsl2ChConfProfImaEnabled OBJECT-TYPE
SYNTAX TruthValue SYNTAX TruthValue
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"IMA Mode Enable. The parameter enables the IMA operation mode "IMA Mode Enable. The parameter enables the IMA operation mode
in the ATM Data Path. Relevant only if the channel is of ATM in the ATM Data Path. Relevant only if the channel is an ATM
Data Path. When in 'enable' state, the ATM data path should Data Path. When in 'enable' state, the ATM data path should
comply with the requirements for IMA transmission." comply with the requirements for IMA transmission."
REFERENCE "ITU-T G.997.1, paragraph 7.3.4.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.4.1"
DEFVAL { false } DEFVAL { false }
::= { adsl2ChConfProfileEntry 19 } ::= { adsl2ChConfProfileEntry 19 }
adsl2ChConfProfRowStatus OBJECT-TYPE adsl2ChConfProfRowStatus OBJECT-TYPE
SYNTAX RowStatus SYNTAX RowStatus
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is used to create a new row or to modify or "This object is used to create a new row or to modify or
delete an existing row in this table. delete an existing row in this table.
A profile is activated by setting this object to 'active'. A profile is activated by setting this object to 'active'.
When 'active' is set, the system will validate the profile. When 'active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of service Before a profile can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'), (by setting this object to 'destroy' or 'notInService'),
it must be first unreferenced from all associated it must first be unreferenced from all associated
templates." templates."
::= { adsl2ChConfProfileEntry 20 } ::= { adsl2ChConfProfileEntry 20 }
------------------------------------------------ ------------------------------------------------
-- adsl2LineAlarmConfTemplateTable -- -- adsl2LineAlarmConfTemplateTable --
------------------------------------------------ ------------------------------------------------
adsl2LineAlarmConfTemplateTable OBJECT-TYPE adsl2LineAlarmConfTemplateTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineAlarmConfTemplateEntry SYNTAX SEQUENCE OF Adsl2LineAlarmConfTemplateEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2LineAlarmConfTemplateTable contains "The table adsl2LineAlarmConfTemplateTable contains
ADSL2 line configuration template. ADSL2 line configuration templates.
Entries in this table MUST be maintained in a Entries in this table MUST be maintained in a
persistent manner." persistent manner."
::= { adsl2ProfileAlarmConf 1 } ::= { adsl2ProfileAlarmConf 1 }
adsl2LineAlarmConfTemplateEntry OBJECT-TYPE adsl2LineAlarmConfTemplateEntry OBJECT-TYPE
SYNTAX Adsl2LineAlarmConfTemplateEntry SYNTAX Adsl2LineAlarmConfTemplateEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2LineAlarmConfTemplateTable contains ADSL2 "The table adsl2LineAlarmConfTemplateTable contains ADSL2
line PM thresholds template. line PM thresholds templates.
A default template with an index of 'DEFVAL' will A default template with an index of 'DEFVAL' will
always exist and its parameters will be set to vendor always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this specific values, unless otherwise specified in this
document" document."
INDEX { adsl2LAlarmConfTempTemplateName } INDEX { adsl2LAlarmConfTempTemplateName }
::= { adsl2LineAlarmConfTemplateTable 1 } ::= { adsl2LineAlarmConfTemplateTable 1 }
Adsl2LineAlarmConfTemplateEntry ::= Adsl2LineAlarmConfTemplateEntry ::=
SEQUENCE { SEQUENCE {
adsl2LAlarmConfTempTemplateName SnmpAdminString, adsl2LAlarmConfTempTemplateName SnmpAdminString,
adsl2LAlarmConfTempLineProfile SnmpAdminString, adsl2LAlarmConfTempLineProfile SnmpAdminString,
adsl2LAlarmConfTempChan1ConfProfile SnmpAdminString, adsl2LAlarmConfTempChan1ConfProfile SnmpAdminString,
adsl2LAlarmConfTempChan2ConfProfile SnmpAdminString, adsl2LAlarmConfTempChan2ConfProfile SnmpAdminString,
adsl2LAlarmConfTempChan3ConfProfile SnmpAdminString, adsl2LAlarmConfTempChan3ConfProfile SnmpAdminString,
skipping to change at page 101, line 19 skipping to change at page 101, line 28
SYNTAX SnmpAdminString (SIZE(0..32)) SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The value of this object identifies the row in the ADSL2 "The value of this object identifies the row in the ADSL2
Channel Thresholds Configuration Profile Table Channel Thresholds Configuration Profile Table
(adsl2ChAlarmConfProfileTable) that applies for ADSL2 (adsl2ChAlarmConfProfileTable) that applies for ADSL2
bearer channel #2. The channel profile name specified here bearer channel #2. The channel profile name specified here
must match the name of an existing row in the must match the name of an existing row in the
adsl2ChAlarmConfProfileTable table. If the channel is unused, adsl2ChAlarmConfProfileTable table. If the channel is unused,
then the object is set to a zero length string." then the object is set to a zero-length string."
REFERENCE "DSL Forum TR-90, paragraph 5.4.1" REFERENCE "DSL Forum TR-90, paragraph 5.4.1"
DEFVAL { "" } DEFVAL { "" }
::= { adsl2LineAlarmConfTemplateEntry 4 } ::= { adsl2LineAlarmConfTemplateEntry 4 }
adsl2LAlarmConfTempChan3ConfProfile OBJECT-TYPE adsl2LAlarmConfTempChan3ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32)) SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The value of this object identifies the row in the ADSL2 "The value of this object identifies the row in the ADSL2
Channel Thresholds Configuration Profile Table Channel Thresholds Configuration Profile Table
(adsl2ChAlarmConfProfileTable) that applies for ADSL2 (adsl2ChAlarmConfProfileTable) that applies for ADSL2
bearer channel #3. The channel profile name specified here bearer channel #3. The channel profile name specified here
must match the name of an existing row in the must match the name of an existing row in the
adsl2ChAlarmConfProfileTable table. adsl2ChAlarmConfProfileTable table.
This object may be set to a non-zero length string only if This object may be set to a non-zero-length string only if
adsl2LAlarmConfTempChan2ConfProfile contains a non-zero adsl2LAlarmConfTempChan2ConfProfile contains a non-zero-
length string." length string."
REFERENCE "DSL Forum TR-90, paragraph 5.4.1" REFERENCE "DSL Forum TR-90, paragraph 5.4.1"
DEFVAL { "" } DEFVAL { "" }
::= { adsl2LineAlarmConfTemplateEntry 5 } ::= { adsl2LineAlarmConfTemplateEntry 5 }
adsl2LAlarmConfTempChan4ConfProfile OBJECT-TYPE adsl2LAlarmConfTempChan4ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32)) SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The value of this object identifies the row in the ADSL2 "The value of this object identifies the row in the ADSL2
Channel Thresholds Configuration Profile Table Channel Thresholds Configuration Profile Table
(adsl2ChAlarmConfProfileTable) that applies for ADSL2 (adsl2ChAlarmConfProfileTable) that applies for ADSL2
bearer channel #4. The channel profile name specified here bearer channel #4. The channel profile name specified here
must match the name of an existing row in the must match the name of an existing row in the
adsl2ChAlarmConfProfileTable table. adsl2ChAlarmConfProfileTable table.
This object may be set to a non-zero length string only if This object may be set to a non-zero-length string only if
adsl2LAlarmConfTempChan3ConfProfile contains a non-zero adsl2LAlarmConfTempChan3ConfProfile contains a non-zero-
length string." length string."
REFERENCE "DSL Forum TR-90, paragraph 5.4.1" REFERENCE "DSL Forum TR-90, paragraph 5.4.1"
DEFVAL { "" } DEFVAL { "" }
::= { adsl2LineAlarmConfTemplateEntry 6 } ::= { adsl2LineAlarmConfTemplateEntry 6 }
adsl2LAlarmConfTempRowStatus OBJECT-TYPE adsl2LAlarmConfTempRowStatus OBJECT-TYPE
SYNTAX RowStatus SYNTAX RowStatus
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is used to create a new row or to modify or "This object is used to create a new row or to modify or
delete an existing row in this table. delete an existing row in this table.
A template is activated by setting this object to 'active'. A template is activated by setting this object to 'active'.
When 'active' is set, the system will validate the template. When 'active' is set, the system will validate the template.
Before a template can be deleted or taken out of service Before a template can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'), (by setting this object to 'destroy' or 'notInService'),
it must be first unreferenced from all associated it must first be unreferenced from all associated
lines." lines."
::= { adsl2LineAlarmConfTemplateEntry 7 } ::= { adsl2LineAlarmConfTemplateEntry 7 }
------------------------------------------------ ------------------------------------------------
-- adsl2LineAlarmConfProfileTable -- -- adsl2LineAlarmConfProfileTable --
------------------------------------------------ ------------------------------------------------
adsl2LineAlarmConfProfileTable OBJECT-TYPE adsl2LineAlarmConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineAlarmConfProfileEntry SYNTAX SEQUENCE OF Adsl2LineAlarmConfProfileEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
skipping to change at page 103, line 4 skipping to change at page 103, line 13
persistent manner." persistent manner."
::= { adsl2ProfileAlarmConf 2 } ::= { adsl2ProfileAlarmConf 2 }
adsl2LineAlarmConfProfileEntry OBJECT-TYPE adsl2LineAlarmConfProfileEntry OBJECT-TYPE
SYNTAX Adsl2LineAlarmConfProfileEntry SYNTAX Adsl2LineAlarmConfProfileEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2LineAlarmConfProfileTable contains ADSL2 "The table adsl2LineAlarmConfProfileTable contains ADSL2
line PM thresholds profiles. line PM thresholds profiles.
A default profile with an index of 'DEFVAL' will A default profile with an index of 'DEFVAL' will
always exist and its parameters will be set to vendor always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this specific values, unless otherwise specified in this
document" document."
INDEX { adsl2LineAlarmConfProfileName } INDEX { adsl2LineAlarmConfProfileName }
::= { adsl2LineAlarmConfProfileTable 1 } ::= { adsl2LineAlarmConfProfileTable 1 }
Adsl2LineAlarmConfProfileEntry ::= Adsl2LineAlarmConfProfileEntry ::=
SEQUENCE { SEQUENCE {
adsl2LineAlarmConfProfileName SnmpAdminString, adsl2LineAlarmConfProfileName SnmpAdminString,
adsl2LineAlarmConfProfileAtucThresh15MinFecs adsl2LineAlarmConfProfileAtucThresh15MinFecs
HCPerfIntervalThreshold, HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAtucThresh15MinEs adsl2LineAlarmConfProfileAtucThresh15MinEs
HCPerfIntervalThreshold, HCPerfIntervalThreshold,
skipping to change at page 104, line 8 skipping to change at page 104, line 17
"This object identifies a row in this table." "This object identifies a row in this table."
::= { adsl2LineAlarmConfProfileEntry 1 } ::= { adsl2LineAlarmConfProfileEntry 1 }
adsl2LineAlarmConfProfileAtucThresh15MinFecs OBJECT-TYPE adsl2LineAlarmConfProfileAtucThresh15MinFecs OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold SYNTAX HCPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A threshold for the adsl2PMLCurr15MFecs counter, "A threshold for the adsl2PMLCurr15MFecs counter,
when adsl2PMLCurrUnit is ATUC {1}. when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the The value 0 means that no threshold is specified for the
associated counter." associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 2 } ::= { adsl2LineAlarmConfProfileEntry 2 }
adsl2LineAlarmConfProfileAtucThresh15MinEs OBJECT-TYPE adsl2LineAlarmConfProfileAtucThresh15MinEs OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold SYNTAX HCPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A threshold for the adsl2PMLCurr15MEs counter, "A threshold for the adsl2PMLCurr15MEs counter,
when adsl2PMLCurrUnit is ATUC {1}. when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the The value 0 means that no threshold is specified for the
associated counter." associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 3 } ::= { adsl2LineAlarmConfProfileEntry 3 }
adsl2LineAlarmConfProfileAtucThresh15MinSes OBJECT-TYPE adsl2LineAlarmConfProfileAtucThresh15MinSes OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold SYNTAX HCPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A threshold for the adsl2PMLCurr15MSes counter, "A threshold for the adsl2PMLCurr15MSes counter,
when adsl2PMLCurrUnit is ATUC {1}. when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the The value 0 means that no threshold is specified for the
associated counter." associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 4 } ::= { adsl2LineAlarmConfProfileEntry 4 }
adsl2LineAlarmConfProfileAtucThresh15MinLoss OBJECT-TYPE adsl2LineAlarmConfProfileAtucThresh15MinLoss OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold SYNTAX HCPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A threshold for the adsl2PMLCurr15MLoss counter, "A threshold for the adsl2PMLCurr15MLoss counter,
when adsl2PMLCurrUnit is ATUC {1}. when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the The value 0 means that no threshold is specified for the
associated counter." associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 5 } ::= { adsl2LineAlarmConfProfileEntry 5 }
adsl2LineAlarmConfProfileAtucThresh15MinUas OBJECT-TYPE adsl2LineAlarmConfProfileAtucThresh15MinUas OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold SYNTAX HCPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A threshold for the adsl2PMLCurr15MUas counter, "A threshold for the adsl2PMLCurr15MUas counter,
when adsl2PMLCurrUnit is ATUC {1}. when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the The value 0 means that no threshold is specified for the
associated counter." associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 6 } ::= { adsl2LineAlarmConfProfileEntry 6 }
adsl2LineAlarmConfProfileAturThresh15MinFecs OBJECT-TYPE adsl2LineAlarmConfProfileAturThresh15MinFecs OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold SYNTAX HCPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A threshold for the adsl2PMLCurr15MFecs counter, "A threshold for the adsl2PMLCurr15MFecs counter,
when adsl2PMLCurrUnit is ATUR {2}. when adsl2PMLCurrUnit is atur(2).
The value 0 means that no threshold is specified for the The value 0 means that no threshold is specified for the
associated counter." associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 7 } ::= { adsl2LineAlarmConfProfileEntry 7 }
adsl2LineAlarmConfProfileAturThresh15MinEs OBJECT-TYPE adsl2LineAlarmConfProfileAturThresh15MinEs OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold SYNTAX HCPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A threshold for the adsl2PMLCurr15MEs counter, "A threshold for the adsl2PMLCurr15MEs counter,
when adsl2PMLCurrUnit is ATUR {2}. when adsl2PMLCurrUnit is atur(2).
The value 0 means that no threshold is specified for the The value 0 means that no threshold is specified for the
associated counter." associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 8 } ::= { adsl2LineAlarmConfProfileEntry 8 }
adsl2LineAlarmConfProfileAturThresh15MinSes OBJECT-TYPE adsl2LineAlarmConfProfileAturThresh15MinSes OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold SYNTAX HCPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A threshold for the adsl2PMLCurr15MSes counter, "A threshold for the adsl2PMLCurr15MSes counter,
when adsl2PMLCurrUnit is ATUR {2}. when adsl2PMLCurrUnit is atur(2).
The value 0 means that no threshold is specified for the The value 0 means that no threshold is specified for the
associated counter." associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 9 } ::= { adsl2LineAlarmConfProfileEntry 9 }
adsl2LineAlarmConfProfileAturThresh15MinLoss OBJECT-TYPE adsl2LineAlarmConfProfileAturThresh15MinLoss OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold SYNTAX HCPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A threshold for the adsl2PMLCurr15MLoss counter, "A threshold for the adsl2PMLCurr15MLoss counter,
when adsl2PMLCurrUnit is ATUR {2}. when adsl2PMLCurrUnit is atur(2).
The value 0 means that no threshold is specified for the The value 0 means that no threshold is specified for the
associated counter." associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 10 } ::= { adsl2LineAlarmConfProfileEntry 10 }
adsl2LineAlarmConfProfileAturThresh15MinUas OBJECT-TYPE adsl2LineAlarmConfProfileAturThresh15MinUas OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold SYNTAX HCPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A threshold for the adsl2PMLCurr15MUas counter, "A threshold for the adsl2PMLCurr15MUas counter,
when adsl2PMLCurrUnit is ATUR {2}. when adsl2PMLCurrUnit is atur(2).
The value 0 means that no threshold is specified for the The value 0 means that no threshold is specified for the
associated counter." associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1" REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 11 } ::= { adsl2LineAlarmConfProfileEntry 11 }
adsl2LineAlarmConfProfileThresh15MinFailedFullInt OBJECT-TYPE adsl2LineAlarmConfProfileThresh15MinFailedFullInt OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
skipping to change at page 107, line 37 skipping to change at page 107, line 45
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is used to create a new row or to modify or "This object is used to create a new row or to modify or
delete an existing row in this table. delete an existing row in this table.
A profile is activated by setting this object to 'active'. A profile is activated by setting this object to 'active'.
When 'active' is set, the system will validate the profile. When 'active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of service Before a profile can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'), (by setting this object to 'destroy' or 'notInService'),
it must be first unreferenced from all associated it must first be unreferenced from all associated
templates." templates."
::= { adsl2LineAlarmConfProfileEntry 14 } ::= { adsl2LineAlarmConfProfileEntry 14 }
------------------------------------------------ ------------------------------------------------
-- adsl2ChAlarmConfProfileTable -- -- adsl2ChAlarmConfProfileTable --
------------------------------------------------ ------------------------------------------------
adsl2ChAlarmConfProfileTable OBJECT-TYPE adsl2ChAlarmConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2ChAlarmConfProfileEntry SYNTAX SEQUENCE OF Adsl2ChAlarmConfProfileEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
skipping to change at page 108, line 17 skipping to change at page 108, line 26
::= { adsl2ProfileAlarmConf 3 } ::= { adsl2ProfileAlarmConf 3 }
adsl2ChAlarmConfProfileEntry OBJECT-TYPE adsl2ChAlarmConfProfileEntry OBJECT-TYPE
SYNTAX Adsl2ChAlarmConfProfileEntry SYNTAX Adsl2ChAlarmConfProfileEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2ChAlarmConfProfileTable contains ADSL2 "The table adsl2ChAlarmConfProfileTable contains ADSL2
channel PM thresholds profiles. channel PM thresholds profiles.
A default profile with an index of 'DEFVAL' will A default profile with an index of 'DEFVAL' will
always exist and its parameters will be set to vendor-specific always exist, and its parameters will be set to vendor-
values, unless otherwise specified in this document" specific values, unless otherwise specified in this document."
INDEX { adsl2ChAlarmConfProfileName } INDEX { adsl2ChAlarmConfProfileName }
::= { adsl2ChAlarmConfProfileTable 1 } ::= { adsl2ChAlarmConfProfileTable 1 }
Adsl2ChAlarmConfProfileEntry ::= Adsl2ChAlarmConfProfileEntry ::=
SEQUENCE { SEQUENCE {
adsl2ChAlarmConfProfileName adsl2ChAlarmConfProfileName
SnmpAdminString, SnmpAdminString,
adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations
Unsigned32, Unsigned32,
adsl2ChAlarmConfProfileAtucThresh15MinCorrected Unsigned32, adsl2ChAlarmConfProfileAtucThresh15MinCorrected Unsigned32,
skipping to change at page 108, line 42 skipping to change at page 109, line 4
adsl2ChAlarmConfProfileRowStatus RowStatus adsl2ChAlarmConfProfileRowStatus RowStatus
} }
adsl2ChAlarmConfProfileName OBJECT-TYPE adsl2ChAlarmConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32)) SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object identifies a row in this table." "This object identifies a row in this table."
::= { adsl2ChAlarmConfProfileEntry 1 } ::= { adsl2ChAlarmConfProfileEntry 1 }
adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations OBJECT-TYPE adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A threshold for the adsl2PMChCurr15MCodingViolations "A threshold for the adsl2PMChCurr15MCodingViolations
counter, when adsl2PMChCurrUnit is ATUC {1}. counter, when adsl2PMChCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the The value 0 means that no threshold is specified for the
associated counter." associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2" REFERENCE "ITU-T G.997.1, paragraph 7.3.2"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2ChAlarmConfProfileEntry 2 } ::= { adsl2ChAlarmConfProfileEntry 2 }
adsl2ChAlarmConfProfileAtucThresh15MinCorrected OBJECT-TYPE adsl2ChAlarmConfProfileAtucThresh15MinCorrected OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A threshold for the adsl2PMChCurr15MCorrectedBlocks "A threshold for the adsl2PMChCurr15MCorrectedBlocks
counter, when adsl2PMChCurrUnit is ATUC {1}. counter, when adsl2PMChCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the The value 0 means that no threshold is specified for the
associated counter." associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2" REFERENCE "ITU-T G.997.1, paragraph 7.3.2"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2ChAlarmConfProfileEntry 3 } ::= { adsl2ChAlarmConfProfileEntry 3 }
adsl2ChAlarmConfProfileAturThresh15MinCodingViolations OBJECT-TYPE adsl2ChAlarmConfProfileAturThresh15MinCodingViolations OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A threshold for the adsl2PMChCurr15MCodingViolations "A threshold for the adsl2PMChCurr15MCodingViolations
counter, when adsl2PMChCurrUnit is ATUR {2}. counter, when adsl2PMChCurrUnit is atur(2).
The value 0 means that no threshold is specified for the The value 0 means that no threshold is specified for the
associated counter." associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2" REFERENCE "ITU-T G.997.1, paragraph 7.3.2"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2ChAlarmConfProfileEntry 4 } ::= { adsl2ChAlarmConfProfileEntry 4 }
adsl2ChAlarmConfProfileAturThresh15MinCorrected OBJECT-TYPE adsl2ChAlarmConfProfileAturThresh15MinCorrected OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A threshold for the adsl2PMChCurr15MCorrectedBlocks "A threshold for the adsl2PMChCurr15MCorrectedBlocks
counter, when adsl2PMChCurrUnit is ATUR {2}. counter, when adsl2PMChCurrUnit is atur(2).
The value 0 means that no threshold is specified for the The value 0 means that no threshold is specified for the
associated counter." associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2" REFERENCE "ITU-T G.997.1, paragraph 7.3.2"
DEFVAL { 0 } DEFVAL { 0 }
::= { adsl2ChAlarmConfProfileEntry 5 } ::= { adsl2ChAlarmConfProfileEntry 5 }
adsl2ChAlarmConfProfileRowStatus OBJECT-TYPE adsl2ChAlarmConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus SYNTAX RowStatus
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is used to create a new row or to modify or "This object is used to create a new row or to modify or
delete an existing row in this table. delete an existing row in this table.
A profile is activated by setting this object to 'active'. A profile is activated by setting this object to 'active'.
When 'active' is set, the system will validate the profile. When 'active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of service Before a profile can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'), (by setting this object to 'destroy' or 'notInService'),
it must be first unreferenced from all associated it must first be unreferenced from all associated
templates." templates."
::= { adsl2ChAlarmConfProfileEntry 6 } ::= { adsl2ChAlarmConfProfileEntry 6 }
------------------------------------------------ ------------------------------------------------
-- PM line current counters -- -- PM line current counters --
------------------------------------------------ ------------------------------------------------
adsl2PMLineCurrTable OBJECT-TYPE adsl2PMLineCurrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineCurrEntry SYNTAX SEQUENCE OF Adsl2PMLineCurrEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2PMLineCurrTable contains current Performance "The table adsl2PMLineCurrTable contains current Performance
Monitoring results of ADSL2 line. " Monitoring results of ADSL2 lines."
::= { adsl2PMLine 1 } ::= { adsl2PMLine 1 }
adsl2PMLineCurrEntry OBJECT-TYPE adsl2PMLineCurrEntry OBJECT-TYPE
SYNTAX Adsl2PMLineCurrEntry SYNTAX Adsl2PMLineCurrEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The table adsl2PMLineCurrTable contains current Performance "The table adsl2PMLineCurrTable contains current Performance
Monitoring results of ADSL2 line. Monitoring results of ADSL2 lines.
The index of this table is an interface index where the The index of this table consists of an interface index, where
interface has an ifType of adsl2(230) and the termination the interface has an ifType of adsl2plus(238), along with a
unit. termination unit.
The PM counters in the table are not reset even when the xtU The PM counters in the table are not reset even when the XTU
is reinitialized. They are re-initialized only when the is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized. " agent itself is reset or reinitialized. "
INDEX { ifIndex, adsl2PMLCurrUnit } INDEX { ifIndex, adsl2PMLCurrUnit }
::= { adsl2PMLineCurrTable 1 } ::= { adsl2PMLineCurrTable 1 }
Adsl2PMLineCurrEntry ::= Adsl2PMLineCurrEntry ::=
SEQUENCE { SEQUENCE {
adsl2PMLCurrUnit Adsl2Unit, adsl2PMLCurrUnit Adsl2Unit,
adsl2PMLCurrValidIntervals Unsigned32, adsl2PMLCurrValidIntervals Unsigned32,
adsl2PMLCurrInvalidIntervals Unsigned32, adsl2PMLCurrInvalidIntervals Unsigned32,
adsl2PMLCurr15MTimeElapsed HCPerfTimeElapsed, adsl2PMLCurr15MTimeElapsed HCPerfTimeElapsed,
adsl2PMLCurr15MFecs Counter32, adsl2PMLCurr15MFecs Counter32,
adsl2PMLCurr15MEs Counter32, adsl2PMLCurr15MEs Counter32,
adsl2PMLCurr15MSes Counter32, adsl2PMLCurr15MSes Counter32,
adsl2PMLCurr15MLoss Counter32, adsl2PMLCurr15MLoss Counter32,
skipping to change at page 111, line 21 skipping to change at page 111, line 30
adsl2PMLCurr1DaySes Counter32, adsl2PMLCurr1DaySes Counter32,
adsl2PMLCurr1DayLoss Counter32, adsl2PMLCurr1DayLoss Counter32,
adsl2PMLCurr1DayUas Counter32 adsl2PMLCurr1DayUas Counter32
} }
adsl2PMLCurrUnit OBJECT-TYPE adsl2PMLCurrUnit OBJECT-TYPE
SYNTAX Adsl2Unit SYNTAX Adsl2Unit
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The termination unit ATUC{1} or ATUR{2}." "The termination unit atuc(1) or atur(2)."
::= { adsl2PMLineCurrEntry 1 } ::= { adsl2PMLineCurrEntry 1 }
adsl2PMLCurrValidIntervals OBJECT-TYPE adsl2PMLCurrValidIntervals OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Valid intervals." "Valid intervals."
::= { adsl2PMLineCurrEntry 2 } ::= { adsl2PMLineCurrEntry 2 }
skipping to change at page 111, line 47 skipping to change at page 112, line 8
"Invalid intervals." "Invalid intervals."
::= { adsl2PMLineCurrEntry 3 } ::= { adsl2PMLineCurrEntry 3 }
adsl2PMLCurr15MTimeElapsed OBJECT-TYPE adsl2PMLCurr15MTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed SYNTAX HCPerfTimeElapsed
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Total elapsed seconds since this PM interval began. "Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the xtU Note that the PM counters are not reset even when the XTU
is reinitialized. They are re-initialized only when the is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized. " agent itself is reset or reinitialized. "
::= { adsl2PMLineCurrEntry 4 } ::= { adsl2PMLineCurrEntry 4 }
adsl2PMLCurr15MFecs OBJECT-TYPE adsl2PMLCurr15MFecs OBJECT-TYPE
SYNTAX Counter32 SYNTAX Counter32
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of seconds during this interval that there was at least "Count of seconds during this interval where there was at least
one FEC correction event for one or more bearer channels in one FEC correction event for one or more bearer channels in
this line. This parameter is inhibited during UAS or SES." this line. This parameter is inhibited during UAS or SES."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 5 } ::= { adsl2PMLineCurrEntry 5 }
adsl2PMLCurr15MEs OBJECT-TYPE adsl2PMLCurr15MEs OBJECT-TYPE
SYNTAX Counter32 SYNTAX Counter32
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of seconds during this interval that there was: "Count of seconds during this interval where there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR ATU-C: CRC-8 >= 1 for one or more bearer channels OR
LOS >= 1 OR SEF >=1 OR LPR >= 1 LOS >= 1 OR SEF >=1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR ATU-R: FEBE >= 1 for one or more bearer channels OR
LOS-FE >=1 OR RDI >=1 OR LPR-FE >=1 . LOS-FE >=1 OR RDI >=1 OR LPR-FE >=1 .
This parameter is inhibited during UAS." This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 6 } ::= { adsl2PMLineCurrEntry 6 }
adsl2PMLCurr15MSes OBJECT-TYPE adsl2PMLCurr15MSes OBJECT-TYPE
SYNTAX Counter32 SYNTAX Counter32
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of seconds during this interval that there was: "Count of seconds during this interval where there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1 LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR ATU-R: (FEBE summed over all bearer channels) >= 18 OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1 . LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1 .
This parameter is inhibited during UAS." This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 7 } ::= { adsl2PMLineCurrEntry 7 }
adsl2PMLCurr15MLoss OBJECT-TYPE adsl2PMLCurr15MLoss OBJECT-TYPE
SYNTAX Counter32 SYNTAX Counter32
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of seconds during this interval that there was LOS (or "Count of seconds during this interval where there was LOS (or
LOS-FE for ATU-R)." LOS-FE for ATU-R)."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 8 } ::= { adsl2PMLineCurrEntry 8 }
adsl2PMLCurr15MUas OBJECT-TYPE adsl2PMLCurr15MUas OBJECT-TYPE
SYNTAX Counter32 SYNTAX Counter32
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
skipping to change at page 113, line 46 skipping to change at page 114, line 7
"Invalid intervals." "Invalid intervals."
::= { adsl2PMLineCurrEntry 11 } ::= { adsl2PMLineCurrEntry 11 }
adsl2PMLCurr1DayTimeElapsed OBJECT-TYPE adsl2PMLCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed SYNTAX HCPerfTimeElapsed
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Total elapsed seconds since this PM interval began. "Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the xtU Note that the PM counters are not reset even when the XTU
is reinitialized. They are re-initialized only when the is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized. " agent itself is reset or reinitialized. "
::= { adsl2PMLineCurrEntry 12 } ::= { adsl2PMLineCurrEntry 12 }
adsl2PMLCurr1DayFecs OBJECT-TYPE adsl2PMLCurr1DayFecs OBJECT-TYPE
SYNTAX Counter32 SYNTAX Counter32
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of seconds during this interval that there was at least "Count of seconds during this interval where there was at least
one FEC correction event for one or more bearer channels in one FEC correction event for one or more bearer channels in
this line. This parameter is inhibited during UAS or SES." this line. This parameter is inhibited during UAS or SES."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 13 } ::= { adsl2PMLineCurrEntry 13 }
adsl2PMLCurr1DayEs OBJECT-TYPE adsl2PMLCurr1DayEs OBJECT-TYPE
SYNTAX Counter32 SYNTAX Counter32
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of seconds during this interval that there was: "Count of seconds during this interval where there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR ATU-C: CRC-8 >= 1 for one or more bearer channels OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1 LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR ATU-R: FEBE >= 1 for one or more bearer channels OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1.
This parameter is inhibited during UAS." This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 14 } ::= { adsl2PMLineCurrEntry 14 }
adsl2PMLCurr1DaySes OBJECT-TYPE adsl2PMLCurr1DaySes OBJECT-TYPE
SYNTAX Counter32 SYNTAX Counter32
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of seconds during this interval that there was: "Count of seconds during this interval where there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1 LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR ATU-R: (FEBE summed over all bearer channels) >= 18 OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1 LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1
This parameter is inhibited during UAS." This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1" REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 15 } ::= { adsl2PMLineCurrEntry 15 }
adsl2PMLCurr1DayLoss OBJECT-TYPE adsl2PMLCurr1DayLoss OBJECT-TYPE