draft-ietf-adslmib-hdsl2-02.txt   draft-ietf-adslmib-hdsl2-03.txt 
INTERNET-DRAFT B. Ray INTERNET-DRAFT B. Ray
Verilink Corporation Verilink Corporation
R. Abbi R. Abbi
Alcatel Alcatel
August 2000 October 2000
Definitions of Managed Objects for HDSL2 and SHDSL Lines Definitions of Managed Objects for HDSL2 and SHDSL Lines
draft-ietf-adslmib-hdsl2-02.txt draft-ietf-adslmib-hdsl2-03.txt
Status of this Memo Status of this Memo
This document is an Internet-Draft and is in full conformance with This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC 2026. all provisions of Section 10 of RFC 2026.
Internet-Drafts are working documents of the Internet Engineering Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that other Task Force (IETF), its areas, and its working groups. Note that other
groups may also distribute working documents as Internet-Drafts. groups may also distribute working documents as Internet-Drafts.
skipping to change at line 54 skipping to change at line 53
Table of Contents Table of Contents
1. Abstract .................................................. 2 1. Abstract .................................................. 2
2. The SNMPv2 Network Management Framework ................... 2 2. The SNMPv2 Network Management Framework ................... 2
3. Introduction .............................................. 3 3. Introduction .............................................. 3
3.1 Relationship of the MIB with Standard MIBs ................ 4 3.1 Relationship of the MIB with Standard MIBs ................ 4
4. Conventions used in the MIB ............................... 5 4. Conventions used in the MIB ............................... 5
4.1 Naming Conventions ........................................ 5 4.1 Naming Conventions ........................................ 5
4.2 Textual Conventions ....................................... 5 4.2 Textual Conventions ....................................... 5
4.3 Structure ................................................. 6 4.3 Structure ................................................. 6
4.4 Counters, Interval Buckets and Thresholds ................. 8 4.4 Counters, Interval Buckets and Thresholds ................. 9
4.5 Profiles .................................................. 9 4.5 Profiles .................................................. 9
4.6 Traps ..................................................... 10 4.6 Traps ..................................................... 10
5. Conformance and Compliance ................................ 11 5. Conformance and Compliance ................................ 11
6. Definitions ............................................... 11 6. Definitions ............................................... 12
7. Security Considerations ................................... 42 7. Security Considerations ................................... 47
8. Acknowledgments ........................................... 42 8. Acknowledgments ........................................... 48
9. References ................................................ 43 9. References ................................................ 48
10. Intellectual Property Notice .............................. 44 10. Intellectual Property Notice .............................. 50
11. Authors' Addresses ........................................ 45 11. Authors' Addresses ........................................ 50
12. Full Copyright Statement .................................. 45 12. Full Copyright Statement .................................. 50
1. Abstract 1. Abstract
This document defines an experimental portion of the Management This document defines an experimental portion of the Management
Information Base (MIB) MIB module for use with network management Information Base (MIB) MIB module for use with network management
protocols in the Internet community. In particular, it describes protocols in the Internet community. In particular, it describes
objects used for managing HDSL2 and SHDSL interfaces. objects used for managing HDSL2 and SHDSL interfaces.
This document specifies a MIB module in a manner that is both compliant This document specifies a MIB module in a manner that is both compliant
to the SNMPv2 SMI, and semantically identical to the peer SNMPv1 to the SNMPv2 SMI, and semantically identical to the peer SNMPv1
skipping to change at line 97 skipping to change at line 96
STD 16, RFC 1155 [2], STD 16, RFC 1212 [3] and RFC 1215 [4]. STD 16, RFC 1155 [2], STD 16, RFC 1212 [3] and RFC 1215 [4].
The second version, called SMIv2, is described in STD 58, RFC The second version, called SMIv2, is described in STD 58, RFC
2578 [5], STD 58, RFC 2579 [6] and STD 58, RFC 2580 [7]. 2578 [5], STD 58, RFC 2579 [6] and STD 58, RFC 2580 [7].
o Message protocols for transferring management information. The o Message protocols for transferring management information. The
first version of the SNMP message protocol is called SNMPv1 and first version of the SNMP message protocol is called SNMPv1 and
described in STD 15, RFC 1157 [8]. A second version of the SNMP described in STD 15, RFC 1157 [8]. A second version of the SNMP
message protocol, which is not an Internet standards track message protocol, which is not an Internet standards track
protocol, is called SNMPv2c and described in RFC 1901 [9] and protocol, is called SNMPv2c and described in RFC 1901 [9] and
RFC 1906 [10]. The third version of the message protocol is RFC 1906 [10]. The third version of the message protocol is
called SNMPv3 and described in RFC 1906 [10], RFC 2572 [11] and
RFC 2574 [12].
Expires November 8, 2000 Page [2] Expires November 8, 2000 Page [2]
called SNMPv3 and described in RFC 1906 [10], RFC 2572 [11] and
RFC 2574 [12].
o Protocol operations for accessing management information. The o Protocol operations for accessing management information. The
first set of protocol operations and associated PDU formats is first set of protocol operations and associated PDU formats is
described in STD 15, RFC 1157 [8]. A second set of protocol described in STD 15, RFC 1157 [8]. A second set of protocol
operations and associated PDU formats is described in RFC 1905 operations and associated PDU formats is described in RFC 1905
[13]. [13].
o A set of fundamental applications described in RFC 2573 [14] o A set of fundamental applications described in RFC 2573 [14]
and the view-based access control mechanism described in RFC and the view-based access control mechanism described in RFC
2575 [15]. 2575 [15].
skipping to change at line 153 skipping to change at line 152
the object type. the object type.
3. Introduction 3. Introduction
This document describes an SNMP MIB for managing HDSL2/SHDSL Lines. This document describes an SNMP MIB for managing HDSL2/SHDSL Lines.
The MIB is intended to be compatible with both the SNMPv1 and SNMPv2. The MIB is intended to be compatible with both the SNMPv1 and SNMPv2.
These definitions are based upon the specifications for the HDSL2 and These definitions are based upon the specifications for the HDSL2 and
SHDSL Embedded Operations Channel (EOC) as defined in ANSI SHDSL Embedded Operations Channel (EOC) as defined in ANSI
T1E1.4/2000-006 [18] and ITU G.991.2 (ex G.SHDSL) [19]. T1E1.4/2000-006 [18] and ITU G.991.2 (ex G.SHDSL) [19].
Expires November 8, 2000 Page [3]
The MIB will eventually be located in the MIB tree under MIB 2 The MIB will eventually be located in the MIB tree under MIB 2
transmission, as discussed in the MIB-2 Integration (RFC 1213 [20] and transmission, as discussed in the MIB-2 Integration (RFC 1213 [20] and
RFC 2863 [21]) section of this document. Until approved by the IETF, RFC 2863 [21]) section of this document. Until approved by the IETF,
vendors may also choose to support it under the experimental tree. vendors may also choose to support it under the experimental tree.
Expires November 8, 2000 Page [3]
NOTE TO RFC EDITOR: please replace the above paragraph with the NOTE TO RFC EDITOR: please replace the above paragraph with the
following paragraph when appropriate: following paragraph when appropriate:
The MIB is located in the MIB tree under MIB-2 transmission, as The MIB is located in the MIB tree under MIB-2 transmission, as
discussing in the MIB-2 Integration (RFC 1213 [20] and RFC 2863 [21]) discussing in the MIB-2 Integration (RFC 1213 [20] and RFC 2863 [21])
section of this document. section of this document.
3.1. Relationship of the HDSL2/SHDSL Line MIB with Standard MIBs 3.1. Relationship of the HDSL2/SHDSL Line MIB with Standard MIBs
This section outlines the relationship of this MIB with other MIBs This section outlines the relationship of this MIB with other MIBs
skipping to change at line 210 skipping to change at line 209
The following attributes are part of the mandatory ifGeneral group in The following attributes are part of the mandatory ifGeneral group in
RFC 2863 [21], and are not duplicated in the HDSL2/SHDSL Line MIB. RFC 2863 [21], and are not duplicated in the HDSL2/SHDSL Line MIB.
=================================================================== ===================================================================
ifIndex Interface index. ifIndex Interface index.
ifDescr See interfaces MIB [21]. ifDescr See interfaces MIB [21].
ifType hdsl2(168) or shdsl(169). ifType hdsl2(168) or shdsl(169).
Expires November 8, 2000 Page [4]
ifSpeed Set as appropriate. ifSpeed Set as appropriate.
(This is fixed at 1552000 for HDSL2 lines) (This is fixed at 1552000 for HDSL2 lines)
ifPhysAddress This object should have an octet string ifPhysAddress This object should have an octet string
with zero length. with zero length.
Expires November 8, 2000 Page [4]
ifAdminStatus See interfaces MIB [21]. ifAdminStatus See interfaces MIB [21].
ifOperStatus See interfaces MIB [21]. ifOperStatus See interfaces MIB [21].
ifLastChange See interfaces MIB [21]. ifLastChange See interfaces MIB [21].
ifName See interfaces MIB [21]. ifName See interfaces MIB [21].
ifLinkUpDownTrapEnable Default to enabled(1). ifLinkUpDownTrapEnable Default to enabled(1).
skipping to change at line 263 skipping to change at line 262
M. SNR means signal-to-noise ratio. M. SNR means signal-to-noise ratio.
N. UAS means unavailable second. N. UAS means unavailable second.
4.2. Textual Conventions 4.2. Textual Conventions
The following textual conventions are defined to reflect the line The following textual conventions are defined to reflect the line
topology in the MIB (further discussed is the following section) topology in the MIB (further discussed is the following section)
and to define the behaviour of the statistics to be maintained and to define the behaviour of the statistics to be maintained
by an agent. by an agent.
Expires November 8, 2000 Page [5]
o Hdsl2ShdslUnitId : o Hdsl2ShdslUnitId :
This attribute uniquely identifies each unit in a HDSL2/SHDSL span. This attribute uniquely identifies each unit in a HDSL2/SHDSL span.
It mirrors the EOC addressing mechanism: It mirrors the EOC addressing mechanism:
xtuC(1) - CO terminal unit xtuC(1) - CO terminal unit
xtuR(2) - CPE terminal unit xtuR(2) - CPE terminal unit
xru1(3) .. xru8(10) - regenerators, numbered from xru1(3) .. xru8(10) - regenerators, numbered from
central office side central office side
Expires November 8, 2000 Page [5]
o Hdsl2ShdslUnitSide: o Hdsl2ShdslUnitSide:
This attribute references the two sides of a unit: This attribute references the two sides of a unit:
networkSide(1) - N in figure 2, below networkSide(1) - N in figure 2, below
customerSide(2) - C in figure 2, below customerSide(2) - C in figure 2, below
o Hdsl2ShdslWirePair: o Hdsl2ShdslWirePair:
This attribute references the wire-pairs connecting the units: This attribute references the wire-pairs connecting the units:
wirePair1(1) - First pair for HDSL2/SHDSL. wirePair1(1) - First pair for HDSL2/SHDSL.
wirePair2(2) - Optional second pair for SHDSL only. wirePair2(2) - Optional second pair for SHDSL only.
o Hdsl2ShdslTransmissionModeType:
This attribute specifies the regional setting for a SHDSL line.
region1(1) - ITU-T G.991.2 Annex A.
region2(2) - ITU-T G.991.2 Annex B.
region3(3) - ITU-T G.991.2 Annex C.
o Hdsl2ShdslPerfCurrDayCount: o Hdsl2ShdslPerfCurrDayCount:
This attribute defines the behaviour of the 1-day (24 hour) This attribute defines the behaviour of the 1-day (24 hour)
gauges found in the MIB. gauges found in the MIB.
o Hdsl2Shdsl1DayIntervalCount: o Hdsl2Shdsl1DayIntervalCount:
This attribute defines the behaviour of the 1-day (24 hour) This attribute defines the behaviour of the 1-day (24 hour)
interval counters found in the MIB. interval counters found in the MIB.
skipping to change at line 310 skipping to change at line 316
o Hdsl2ShdslPerfIntervalThreshold: o Hdsl2ShdslPerfIntervalThreshold:
This attribute defines the behaviour of the alarm thresholds found This attribute defines the behaviour of the alarm thresholds found
in the MIB. in the MIB.
4.3. Structure 4.3. Structure
The MIB is structured into following MIB groups: The MIB is structured into following MIB groups:
Expires November 8, 2000 Page [6]
o Span Configuration Group: o Span Configuration Group:
This group supports MIB objects for configuring parameters for This group supports MIB objects for configuring parameters for
the HDSL2/SHDSL span. It contains the following table(s): the HDSL2/SHDSL span. It contains the following table(s):
- hdsl2ShdslSpanConfTable - hdsl2ShdslSpanConfTable
o Span Status Group:
This group supports MIB objects for retrieving span status
information. It contains the following table(s):
- hdsl2ShdslSpanStatusTable
o Unit Inventory Group: o Unit Inventory Group:
This group supports MIB objects for retrieving unit inventory This group supports MIB objects for retrieving unit inventory
information about units in HDSL2/SHDSL lines via the EOC. It information about units in HDSL2/SHDSL lines via the EOC. It
contains the following table(s): contains the following table(s):
- hdsl2ShdslInventoryTable - hdsl2ShdslInventoryTable
o Segment Endpoint Configuration Group: o Segment Endpoint Configuration Group:
This group supports MIB objects for configuring parameters for This group supports MIB objects for configuring parameters for
the HDSL2/SHDSL segment endpoints. It contains the following the HDSL2/SHDSL segment endpoints. It contains the following
Expires November 8, 2000 Page [6]
table(s): table(s):
- hdsl2ShdslEndpointConfTable - hdsl2ShdslEndpointConfTable
o Segment Endpoint Current Status/Performance Group: o Segment Endpoint Current Status/Performance Group:
This group supports MIB objects that provide the current This group supports MIB objects that provide the current
status/performance information relating to segment endpoints. status/performance information relating to segment endpoints.
It contains the following table(s): It contains the following table(s):
- hdsl2ShdslEndpointCurrTable - hdsl2ShdslEndpointCurrTable
skipping to change at line 358 skipping to change at line 372
- hdsl2Shdsl15MinIntervalTable - hdsl2Shdsl15MinIntervalTable
o Segment Endpoint 1-Day Interval Status/Performance Group: o Segment Endpoint 1-Day Interval Status/Performance Group:
This group supports MIB objects that provide historic This group supports MIB objects that provide historic
status/performance information relating to segment endpoints status/performance information relating to segment endpoints
in 1-day intervals. It contains the following table(s): in 1-day intervals. It contains the following table(s):
- hdsl2Shdsl1DayIntervalTable - hdsl2Shdsl1DayIntervalTable
Expires November 8, 2000 Page [7]
o Maintenance Group: o Maintenance Group:
This group supports MIB objects for performing maintenance This group supports MIB objects for performing maintenance
operations such as loopbacks for HDSL2/SHDSL lines. It contains operations such as loopbacks for HDSL2/SHDSL lines. It contains
the following table(s): the following table(s):
- hdsl2ShdslEndpointMaintTable - hdsl2ShdslEndpointMaintTable
- hdsl2ShdslUnitMaintTable - hdsl2ShdslUnitMaintTable
o Span Configuration Profile Group: o Span Configuration Profile Group:
skipping to change at line 387 skipping to change at line 403
profiles for HDSL2/SHDSL Segment Endpoints. It contains the profiles for HDSL2/SHDSL Segment Endpoints. It contains the
following table(s): following table(s):
- hdsl2ShdslEndpointAlarmConfProfileTable - hdsl2ShdslEndpointAlarmConfProfileTable
o Notifications Group: o Notifications Group:
This group defines Notiofication messages supported for HDSL2/ This group defines Notiofication messages supported for HDSL2/
SHDSL lines. It defines the following notifications: SHDSL lines. It defines the following notifications:
Expires November 8, 2000 Page [7]
- hdsl2ShdslLoopAttenCrossingTrap - hdsl2ShdslLoopAttenCrossingTrap
- hdsl2ShdslSNRMarginCrossingTrap - hdsl2ShdslSNRMarginCrossingTrap
- hdsl2ShdslPerfESThreshTrap - hdsl2ShdslPerfESThreshTrap
- hdsl2ShdslPerfSESThreshTrap - hdsl2ShdslPerfSESThreshTrap
- hdsl2ShdslPerfCRCanomaliesThreshTrap - hdsl2ShdslPerfCRCanomaliesThreshTrap
- hdsl2ShdslPerfLOSWSThreshTrap - hdsl2ShdslPerfLOSWSThreshTrap
- hdsl2ShdslPerfUASThreshTrap - hdsl2ShdslPerfUASThreshTrap
- hdsl2ShdslSpanInvalidNumRepeaters - hdsl2ShdslSpanInvalidNumRepeaters
- hdsl2ShdslLoopbackFailure
4.3.1 Line Topology 4.3.1 Line Topology
An HDSL2/SHDSL Line consists of a minimum of two units - xtuC (the An HDSL2/SHDSL Line consists of a minimum of two units - xtuC (the
central termination unit) and an xtuR (the remote termination unit). central termination unit) and an xtuR (the remote termination unit).
The line may optionally support up to 8 repeater/regenerator units The line may optionally support up to 8 repeater/regenerator units
(xru) as shown in the figure below. (xru) as shown in the figure below.
Expires November 8, 2000 Page [8]
<-- Network Side Customer Side --> <-- Network Side Customer Side -->
|</////////////////// HDSL2/SHDSL Span ////////////////////>| |</////////////////// HDSL2/SHDSL Span ////////////////////>|
<~~~> <~~~> HDSL2/SHDSL Segments <~~~> <~~~> <~~~> HDSL2/SHDSL Segments <~~~>
+-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+
+ C=1=N C=1=N C=..1..=N C=1=N + + C=1=N C=1=N C=..1..=N C=1=N +
| xtuC | | xru1 | | xru2 | | xru8 | | xtuR | | xtuC | | xru1 | | xru2 | | xru8 | | xtuR |
+ C=2=N C=2=N C=..2..=N C=2=N + + C=2=N C=2=N C=..2..=N C=2=N +
skipping to change at line 442 skipping to change at line 459
Unlike RFC 2493 [22] and RFC 2662 [23], there is no representation Unlike RFC 2493 [22] and RFC 2662 [23], there is no representation
in the MIB for invalid buckets. In those cases where the data for in the MIB for invalid buckets. In those cases where the data for
an interval is suspect or known to be invalid, the agent should an interval is suspect or known to be invalid, the agent should
not report the interval. not report the interval.
There is no requirement for an agent to ensure a fixed relationship There is no requirement for an agent to ensure a fixed relationship
between the start of a fifteen minute and any wall clock; however between the start of a fifteen minute and any wall clock; however
some implementations may align the fifteen minute intervals with some implementations may align the fifteen minute intervals with
quarter hours. Likewise, an implementation may choose to align one quarter hours. Likewise, an implementation may choose to align one
Expires November 8, 2000 Page [8]
day intervals with the start of a day. day intervals with the start of a day.
Counters are not reset when an xU is reinitialized, only when the Counters are not reset when an xU is reinitialized, only when the
agent is reset or reinitialized (or under specific request outside agent is reset or reinitialized (or under specific request outside
the scope of this MIB). the scope of this MIB).
4.5. Profiles 4.5. Profiles
As a managed node can handle a large number of xUs, (e.g., hundreds As a managed node can handle a large number of xUs, (e.g., hundreds
or perhaps thousands of lines), provisioning every parameter on every or perhaps thousands of lines), provisioning every parameter on every
xU may become burdensome. Moreover, most lines are provisioned xU may become burdensome. Moreover, most lines are provisioned
identically; with the same set of parameters. To simplify the identically; with the same set of parameters. To simplify the
provisioning process, this MIB makes use of profiles. A profile is a provisioning process, this MIB makes use of profiles. A profile is a
Expires November 8, 2000 Page [9]
set of parameters that can be shared by multiple lines using the same set of parameters that can be shared by multiple lines using the same
configuration. configuration.
The following profiles are used in this MIB: The following profiles are used in this MIB:
o Span Configuration Profiles - Span configuration profiles contain o Span Configuration Profiles - Span configuration profiles contain
parameters for configuring HDSL2/SHDSL spans. They are defined in parameters for configuring HDSL2/SHDSL spans. They are defined in
the hdsl2ShdslSpanConfProfileTable. Since span configuration the hdsl2ShdslSpanConfProfileTable. Since span configuration
parameters are only applicable for SHDSL, the support for span parameters are only applicable for SHDSL, the support for span
configuration profiles is optional for HDSL2 interfaces. configuration profiles is optional for HDSL2 interfaces.
skipping to change at line 500 skipping to change at line 517
line's profiles have been set, these profiles will be automatically line's profiles have been set, these profiles will be automatically
used by setting hdsl2ShdslEndpointAlarmConfProfile and used by setting hdsl2ShdslEndpointAlarmConfProfile and
hdsl2ShdslSpanConfProfile to `DEFVAL' where appropriate. hdsl2ShdslSpanConfProfile to `DEFVAL' where appropriate.
Profiles are created, assigned, and deleted dynamically using the Profiles are created, assigned, and deleted dynamically using the
profile name and profile row status in each of the four profile tables. profile name and profile row status in each of the four profile tables.
Changes to alarm profiles MUST take effect immediately. Changes to Changes to alarm profiles MUST take effect immediately. Changes to
non-alarm profiles MAY be deferred until the next restart (hard reset non-alarm profiles MAY be deferred until the next restart (hard reset
or soft restart) of the units on the line. Vendors MAY choose to have or soft restart) of the units on the line. Vendors MAY choose to have
Expires November 8, 2000 Page [9]
the non-alarm profile changes take effect immediately. Alarm profiles the non-alarm profile changes take effect immediately. Alarm profiles
are those profile settings found in the are those profile settings found in the
hdsl2ShdslEndpointAlarmConfProfileTable. Non-alarm profiles are those hdsl2ShdslEndpointAlarmConfProfileTable. Non-alarm profiles are those
profile settings found in the hdsl2ShdslSpanConfTable and profile settings found in the hdsl2ShdslSpanConfTable and
hdsl2ShdslSpanConfProfileTable. hdsl2ShdslSpanConfProfileTable.
4.6. Traps 4.6. Traps
The ability to generate the SNMP traps coldStart/WarmStart (per [21]) The ability to generate the SNMP traps coldStart/WarmStart (per [21])
which are per agent (e.g., per DSLAM in such a device), and linkUp / which are per agent (e.g., per DSLAM in such a device), and linkUp /
linkDown (per [21]) -- which are per interface (i.e., HDSL2/SHDSL line) linkDown (per [21]) -- which are per interface (i.e., HDSL2/SHDSL line)
is required. is required.
Expires November 8, 2000 Page [10]
A linkDown trap may be generated whenever any of ES, SES, CRC Anomaly, A linkDown trap may be generated whenever any of ES, SES, CRC Anomaly,
LOSWS, or UAS event occurs. At this operational point, a manager can LOSWS, or UAS event occurs. At this operational point, a manager can
use hdsl2ShdslEndpointCurrStatus for additional detailed information. use hdsl2ShdslEndpointCurrStatus for additional detailed information.
The corresponding linkUp trap MAY be sent when all link failure The corresponding linkUp trap MAY be sent when all link failure
conditions are cleared. conditions are cleared.
The traps defined in this MIB are for initialization failure and for The traps defined in this MIB are for initialization failure and for
the threshold crossings associated with the following events: ES, SES, the threshold crossings associated with the following events: ES, SES,
CRC Anomaly, LOSWS, and UAS. Each threshold has its own CRC Anomaly, LOSWS, and UAS. Each threshold has its own
enable/threshold value. When that value is 0, the trap is disabled. enable/threshold value. When that value is 0, the trap is disabled.
skipping to change at line 559 skipping to change at line 575
A threshold trap occurs whenever the corresponding current 15-minute A threshold trap occurs whenever the corresponding current 15-minute
interval error counter becomes equal to, or exceeds the threshold interval error counter becomes equal to, or exceeds the threshold
value. One trap may be sent per interval per interface. Since the value. One trap may be sent per interval per interface. Since the
current 15-minute counter are reset to 0 every 15 minutes, if the current 15-minute counter are reset to 0 every 15 minutes, if the
condition persists, the trap may recur as often as every 15 minutes. condition persists, the trap may recur as often as every 15 minutes.
For example, to get a trap whenever a "loss of" event occurs (but at For example, to get a trap whenever a "loss of" event occurs (but at
most once every 15 minutes), set the corresponding threshold to 1. The most once every 15 minutes), set the corresponding threshold to 1. The
agent will generate a trap when the event originally occurs. agent will generate a trap when the event originally occurs.
Expires November 8, 2000 Page [10]
Note that the NMS may receive a linkDown trap, as well, if enabled. At Note that the NMS may receive a linkDown trap, as well, if enabled. At
the beginning of the next 15 minute interval, the counter is reset. the beginning of the next 15 minute interval, the counter is reset.
When the first second goes by and the event occurs, the current When the first second goes by and the event occurs, the current
interval bucket will be 1, which equals the threshold and the trap will interval bucket will be 1, which equals the threshold and the trap will
be sent again. be sent again.
5. Conformance and Compliance 5. Conformance and Compliance
For both HDSL2 and SHDSL lines, the following group(s) are mandatory: For both HDSL2 and SHDSL lines, the following group(s) are mandatory:
Expires November 8, 2000 Page [11]
hdsl2ShdslSpanConfGroup hdsl2ShdslSpanConfGroup
hdsl2ShdslSpanStatusGroup
hdsl2ShdslInventoryGroup hdsl2ShdslInventoryGroup
hdsl2ShdslEndpointConfGroup hdsl2ShdslEndpointConfGroup
hdsl2Shdsl15MinIntervalGroup hdsl2Shdsl15MinIntervalGroup
hdsl2Shdsl1DayIntervalGroup hdsl2Shdsl1DayIntervalGroup
hdsl2ShdslMaintenanceGroup hdsl2ShdslMaintenanceGroup
hdsl2ShdslEndpointAlarmConfGroup hdsl2ShdslEndpointAlarmConfGroup
hdsl2ShdslNotificationGroup hdsl2ShdslNotificationGroup
For HDSL2 lines, the following group(s) are optional: For HDSL2 lines, the following group(s) are optional:
hdsl2ShdslSpanConfProfileGroup hdsl2ShdslSpanConfProfileGroup
hdsl2ShdslSpanShdslStatusGroup
6. Definitions 6. Definitions
HDSL2-SHDSL-LINE-MIB DEFINITIONS ::= BEGIN HDSL2-SHDSL-LINE-MIB DEFINITIONS ::= BEGIN
IMPORTS IMPORTS
MODULE-IDENTITY, MODULE-IDENTITY,
OBJECT-TYPE, OBJECT-TYPE,
Counter32, Counter32,
Gauge32, Gauge32,
skipping to change at line 609 skipping to change at line 626
ifIndex FROM IF-MIB ifIndex FROM IF-MIB
PerfCurrentCount, PerfCurrentCount,
PerfIntervalCount FROM PerfHist-TC-MIB PerfIntervalCount FROM PerfHist-TC-MIB
SnmpAdminString FROM SNMP-FRAMEWORK-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB
MODULE-COMPLIANCE, MODULE-COMPLIANCE,
OBJECT-GROUP, OBJECT-GROUP,
NOTIFICATION-GROUP FROM SNMPv2-CONF; NOTIFICATION-GROUP FROM SNMPv2-CONF;
hdsl2ShdslMIB MODULE-IDENTITY hdsl2ShdslMIB MODULE-IDENTITY
LAST-UPDATED "0008210000Z" -- August 21, 2000 LAST-UPDATED "0010020000Z" -- October 2, 2000
ORGANIZATION "ADSLMIB Working Group" ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO CONTACT-INFO
" "
Bob Ray Bob Ray
Expires November 8, 2000 Page [11]
Verilink Corporation Verilink Corporation
127 Jetplex Circle 127 Jetplex Circle
Madison, AL 35758 USA Madison, AL 35758 USA
Tel: +1 256-774-2380 Tel: +1 256-774-2380
Expires November 8, 2000 Page [12]
Fax: +1 256-774-2277 Fax: +1 256-774-2277
E-mail: bray@verilink.com E-mail: bray@verilink.com
Rajesh Abbi Rajesh Abbi
Alcatel USA Alcatel USA
2912 Wake Forest Road 2912 Wake Forest Road
Raleigh, NC 27609-7860 USA Raleigh, NC 27609-7860 USA
Tel: +1 919-950-6194 Tel: +1 919-950-6194
Fax: +1 919-950-6670 Fax: +1 919-950-6670
E-mail: Rajesh.Abbi@usa.alcatel.com E-mail: Rajesh.Abbi@usa.alcatel.com
skipping to change at line 674 skipping to change at line 691
1-day interval. At that time the value of the 1-day interval. At that time the value of the
counter is stored in the previous 1-day history counter is stored in the previous 1-day history
interval, if available, and the current interval interval, if available, and the current interval
counter is restarted at zero. counter is restarted at zero.
In the case where the agent has no valid data available In the case where the agent has no valid data available
for this interval the corresponding object for this interval the corresponding object
instance is not available and upon a retrieval instance is not available and upon a retrieval
request a corresponding error message shall be request a corresponding error message shall be
returned to indicate that this instance does returned to indicate that this instance does
Expires November 8, 2000 Page [12]
not exist (for example, a noSuchName error for not exist (for example, a noSuchName error for
SNMPv1 and a noSuchInstance for SNMPv2 GET SNMPv1 and a noSuchInstance for SNMPv2 GET
Expires November 8, 2000 Page [13]
operation)." operation)."
SYNTAX Gauge32 SYNTAX Gauge32
Hdsl2Shdsl1DayIntervalCount ::= TEXTUAL-CONVENTION Hdsl2Shdsl1DayIntervalCount ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A counter associated with interface performance "A counter associated with interface performance
measurements during the most previous 1-day (24 hour) measurements during the most previous 1-day (24 hour)
measurement interval. The value of this counter is measurement interval. The value of this counter is
equal to the value of the current day counter at equal to the value of the current day counter at
skipping to change at line 732 skipping to change at line 749
DESCRIPTION DESCRIPTION
"This is the unique identification for all units "This is the unique identification for all units
in an HDSL2/SHDSL Span. It is based on the EOC in an HDSL2/SHDSL Span. It is based on the EOC
unit addressing scheme with reference to the xtuC." unit addressing scheme with reference to the xtuC."
SYNTAX INTEGER SYNTAX INTEGER
{ {
xtuC(1), xtuC(1),
xtuR(2), xtuR(2),
xru1(3), xru1(3),
Expires November 8, 2000 Page [13] Expires November 8, 2000 Page [14]
xru2(4), xru2(4),
xru3(5), xru3(5),
xru4(6), xru4(6),
xru5(7), xru5(7),
xru6(8), xru6(8),
xru7(9), xru7(9),
xru8(10) xru8(10)
} }
Hdsl2ShdslUnitSide ::= TEXTUAL-CONVENTION Hdsl2ShdslUnitSide ::= TEXTUAL-CONVENTION
skipping to change at line 767 skipping to change at line 784
DESCRIPTION DESCRIPTION
"This is the referenced pair of wires in an HDSL2/SHDSL "This is the referenced pair of wires in an HDSL2/SHDSL
Segment. HDSL2 only supports a single pair (wirePair1), Segment. HDSL2 only supports a single pair (wirePair1),
while SHDSL supports an optional second pair (wirePair2)." while SHDSL supports an optional second pair (wirePair2)."
SYNTAX INTEGER SYNTAX INTEGER
{ {
wirePair1(1), wirePair1(1),
wirePair2(2) wirePair2(2)
} }
Hdsl2ShdslTransmissionModeType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Contains the regional setting of the HDSL2/SHDSL span,
represented as a bit-map of possible settings. The various
bit positions are:
1 region 1 Indicates ITU-T G.991.2 Annex A.
2 region 2 Indicates ITU-T G.991.2 Annex B.
4 region 3 Indicates ITU-T G.991.2 Annex C."
SYNTAX INTEGER
-- Span Configuration Group -- Span Configuration Group
-- --
hdsl2ShdslSpanConfTable OBJECT-TYPE hdsl2ShdslSpanConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfEntry SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
Expires November 8, 2000 Page [15]
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table supports overall configuration of "This table supports overall configuration of
HDSL2/SHDSL Spans." HDSL2/SHDSL Spans."
::= { hdsl2ShdslMibObjects 1 } ::= { hdsl2ShdslMibObjects 1 }
hdsl2ShdslSpanConfEntry OBJECT-TYPE hdsl2ShdslSpanConfEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanConfEntry SYNTAX Hdsl2ShdslSpanConfEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2ShdslSpanConfTable. Each entry "An entry in the hdsl2ShdslSpanConfTable. Each entry
represents the complete Span in a single HDSL2/SHDSL represents the complete Span in a single HDSL2/SHDSL
line. It is indexed by the ifIndex of the associated line. It is indexed by the ifIndex of the associated
HDSL2/SHDSL line." HDSL2/SHDSL line."
Expires November 8, 2000 Page [14]
INDEX { ifIndex } INDEX { ifIndex }
::= { hdsl2ShdslSpanConfTable 1 } ::= { hdsl2ShdslSpanConfTable 1 }
Hdsl2ShdslSpanConfEntry ::= Hdsl2ShdslSpanConfEntry ::=
SEQUENCE SEQUENCE
{ {
hdsl2ShdslConfNumRepeaters INTEGER, hdsl2ShdslConfNumRepeaters INTEGER,
hdsl2ShdslSpanConfProfile SnmpAdminString, hdsl2ShdslSpanConfProfile SnmpAdminString,
hdsl2ShdslSpanAlarmConfProfile SnmpAdminString hdsl2ShdslSpanAlarmConfProfile SnmpAdminString
} }
skipping to change at line 805 skipping to change at line 836
{ {
hdsl2ShdslConfNumRepeaters INTEGER, hdsl2ShdslConfNumRepeaters INTEGER,
hdsl2ShdslSpanConfProfile SnmpAdminString, hdsl2ShdslSpanConfProfile SnmpAdminString,
hdsl2ShdslSpanAlarmConfProfile SnmpAdminString hdsl2ShdslSpanAlarmConfProfile SnmpAdminString
} }
hdsl2ShdslConfNumRepeaters OBJECT-TYPE hdsl2ShdslConfNumRepeaters OBJECT-TYPE
SYNTAX INTEGER(0..8) SYNTAX INTEGER(0..8)
MAX-ACCESS read-write MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object provisions the number of repeaters/regenerators "This object provisions the number of repeaters/regenerators
in this HDSL2/SHDSL Span." in this HDSL2/SHDSL Span."
::= { hdsl2ShdslSpanConfEntry 1 } ::= { hdsl2ShdslSpanConfEntry 1 }
hdsl2ShdslSpanConfProfile OBJECT-TYPE hdsl2ShdslSpanConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is a pointer to a span configuration profile in "This object is a pointer to a span configuration profile in
the hdsl2ShdslSpanConfProfileTable, which applies to this span. the hdsl2ShdslSpanConfProfileTable, which applies to this span.
The value of this object is the index of the referenced profile The value of this object is the index of the referenced profile
in the hdsl2ShdslSpanConfProfileTable. Note that span in the hdsl2ShdslSpanConfProfileTable. Note that span
configuration profiles are only applicable to SHDSL lines. configuration profiles are only applicable to SHDSL lines.
HDSL2 lines will not support this object. By default, this HDSL2 lines will not support this object. By default, this
object will have the value 'DEFVAL' (the index of the default object will have the value 'DEFVAL' (the index of the default
profile)." profile)."
::= { hdsl2ShdslSpanConfEntry 2 } ::= { hdsl2ShdslSpanConfEntry 2 }
hdsl2ShdslSpanAlarmConfProfile OBJECT-TYPE hdsl2ShdslSpanAlarmConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write MAX-ACCESS read-write
STATUS current STATUS current
Expires November 8, 2000 Page [16]
DESCRIPTION DESCRIPTION
"This object is a pointer to an Alarm configuration profile in "This object is a pointer to an Alarm configuration profile in
the hdsl2ShdslEndpointAlarmConfProfileTable. The value of this the hdsl2ShdslEndpointAlarmConfProfileTable. The value of this
object is the index of the referenced profile in the object is the index of the referenced profile in the
hdsl2ShdslEndpointAlarmConfProfileTable. The alarm threshold hdsl2ShdslEndpointAlarmConfProfileTable. The alarm threshold
configuration in the referenced profile will be used by default configuration in the referenced profile will be used by default
for all segment endpoints in this span. Individual endpoints for all segment endpoints in this span. Individual endpoints
may override this profile by explicitly specifying some other may override this profile by explicitly specifying some other
profile in the hdsl2ShdslEndpointConfTable. By default, this profile in the hdsl2ShdslEndpointConfTable. By default, this
object will have the value 'DEFVAL' (the index of the default object will have the value 'DEFVAL' (the index of the default
profile)." profile)."
::= { hdsl2ShdslSpanConfEntry 3 } ::= { hdsl2ShdslSpanConfEntry 3 }
-- Span Status Group
-- --
Expires November 8, 2000 Page [15] hdsl2ShdslSpanStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides overall status information of
HDSL2/SHDSL spans."
::= { hdsl2ShdslMibObjects 2 }
hdsl2ShdslSpanStatusEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslSpanStatusTable. Each entry
represents the complete span in a single HDSL2/SHDSL
line. It is indexed by the ifIndex of the associated
HDSL2/SHDSL line."
INDEX { ifIndex }
::= { hdsl2ShdslSpanStatusTable 1 }
Hdsl2ShdslSpanStatusEntry ::=
SEQUENCE
{
hdsl2ShdslStatusNumAvailRepeaters INTEGER,
hdsl2ShdslStatusMaxAttainableLineRate Integer32,
hdsl2ShdslStatusActualLineRate Integer32,
hdsl2ShdslStatusTransmissionModeCurrent
Hdsl2ShdslTransmissionModeType
}
hdsl2ShdslStatusNumAvailRepeaters OBJECT-TYPE
SYNTAX INTEGER
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the actual number of repeaters/regenerators
discovered in this HDSL2/SHDSL span."
Expires November 8, 2000 Page [17]
::= { hdsl2ShdslSpanStatusEntry 1 }
hdsl2ShdslStatusMaxAttainableLineRate OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the maximum attainable line rate in this HDSL2/SHDSL
span."
::= { hdsl2ShdslSpanStatusEntry 2 }
hdsl2ShdslStatusActualLineRate OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the actual line rate in this HDSL2/SHDSL span."
::= { hdsl2ShdslSpanStatusEntry 3 }
hdsl2ShdslStatusTransmissionModeCurrent OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the current PSD regional setting of the
HDSL2/SHDSL span."
::= { hdsl2ShdslSpanStatusEntry 4 }
-- Unit Inventory Group
--
hdsl2ShdslInventoryTable OBJECT-TYPE hdsl2ShdslInventoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslInventoryEntry SYNTAX SEQUENCE OF Hdsl2ShdslInventoryEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table supports retrieval of unit inventory information "This table supports retrieval of unit inventory information
available via the EOC from units in a HDSL2/SHDSL line." available via the EOC from units in a HDSL2/SHDSL line."
::= { hdsl2ShdslMibObjects 2 } ::= { hdsl2ShdslMibObjects 3 }
hdsl2ShdslInventoryEntry OBJECT-TYPE hdsl2ShdslInventoryEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslInventoryEntry SYNTAX Hdsl2ShdslInventoryEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2ShdslInventoryTable. Each entry "An entry in the hdsl2ShdslInventoryTable. Each entry
represents inventory information for a single unit in a represents inventory information for a single unit in a
HDSL2/SHDSL line. It is indexed by the ifIndex of the HDSL2/SHDSL line. It is indexed by the ifIndex of the
HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the
associated unit." associated unit."
INDEX { ifIndex, hdsl2ShdslInvIndex } INDEX { ifIndex, hdsl2ShdslInvIndex }
::= { hdsl2ShdslInventoryTable 1 } ::= { hdsl2ShdslInventoryTable 1 }
Expires November 8, 2000 Page [18]
Hdsl2ShdslInventoryEntry ::= Hdsl2ShdslInventoryEntry ::=
SEQUENCE SEQUENCE
{ {
hdsl2ShdslInvIndex Hdsl2ShdslUnitId, hdsl2ShdslInvIndex Hdsl2ShdslUnitId,
hdsl2ShdslInvVendorID Integer32, hdsl2ShdslInvVendorID Integer32,
hdsl2ShdslInvVendorModelNumber DisplayString, hdsl2ShdslInvVendorModelNumber DisplayString,
hdsl2ShdslInvVendorSerialNumber DisplayString, hdsl2ShdslInvVendorSerialNumber DisplayString,
hdsl2ShdslInvVendorEOCSoftwareVersion Integer32, hdsl2ShdslInvVendorEOCSoftwareVersion Integer32,
hdsl2ShdslInvStandardVersion Integer32, hdsl2ShdslInvStandardVersion Integer32,
hdsl2ShdslInvVendorListNumber DisplayString, hdsl2ShdslInvVendorListNumber DisplayString,
hdsl2ShdslInvVendorIssueNumber DisplayString, hdsl2ShdslInvVendorIssueNumber DisplayString,
hdsl2ShdslInvVendorSoftwareVersion DisplayString, hdsl2ShdslInvVendorSoftwareVersion DisplayString,
hdsl2ShdslInvEquipmentCode DisplayString, hdsl2ShdslInvEquipmentCode DisplayString,
hdsl2ShdslInvVendorOther DisplayString hdsl2ShdslInvVendorOther DisplayString,
hdsl2ShdslInvTransmissionModeCapability
Hdsl2ShdslTransmissionModeType
} }
hdsl2ShdslInvIndex OBJECT-TYPE hdsl2ShdslInvIndex OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitId SYNTAX Hdsl2ShdslUnitId
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The index into the hdsl2ShdslInventoryTable." "The index into the hdsl2ShdslInventoryTable."
::= { hdsl2ShdslInventoryEntry 1 } ::= { hdsl2ShdslInventoryEntry 1 }
hdsl2ShdslInvVendorID OBJECT-TYPE hdsl2ShdslInvVendorID OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Vendor ID as reported in an Inventory Response message." "Vendor ID as reported in an Inventory Response message."
::= { hdsl2ShdslInventoryEntry 2 } ::= { hdsl2ShdslInventoryEntry 2 }
Expires November 8, 2000 Page [16]
hdsl2ShdslInvVendorModelNumber OBJECT-TYPE hdsl2ShdslInvVendorModelNumber OBJECT-TYPE
SYNTAX DisplayString SYNTAX DisplayString
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Vendor model number as reported in an Inventory Response "Vendor model number as reported in an Inventory Response
message." message."
::= { hdsl2ShdslInventoryEntry 3 } ::= { hdsl2ShdslInventoryEntry 3 }
hdsl2ShdslInvVendorSerialNumber OBJECT-TYPE hdsl2ShdslInvVendorSerialNumber OBJECT-TYPE
SYNTAX DisplayString SYNTAX DisplayString
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Vendor serial number as reported in an Inventory Response "Vendor serial number as reported in an Inventory Response
message." message."
::= { hdsl2ShdslInventoryEntry 4 } ::= { hdsl2ShdslInventoryEntry 4 }
Expires November 8, 2000 Page [19]
hdsl2ShdslInvVendorEOCSoftwareVersion OBJECT-TYPE hdsl2ShdslInvVendorEOCSoftwareVersion OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Vendor EOC version as reported in an Inventory Response "Vendor EOC version as reported in an Inventory Response
message." message."
::= { hdsl2ShdslInventoryEntry 5 } ::= { hdsl2ShdslInventoryEntry 5 }
hdsl2ShdslInvStandardVersion OBJECT-TYPE hdsl2ShdslInvStandardVersion OBJECT-TYPE
skipping to change at line 958 skipping to change at line 1063
hdsl2ShdslInvVendorIssueNumber OBJECT-TYPE hdsl2ShdslInvVendorIssueNumber OBJECT-TYPE
SYNTAX DisplayString SYNTAX DisplayString
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Vendor issue number as reported in an Inventory Response "Vendor issue number as reported in an Inventory Response
message." message."
::= { hdsl2ShdslInventoryEntry 8 } ::= { hdsl2ShdslInventoryEntry 8 }
Expires November 8, 2000 Page [17]
hdsl2ShdslInvVendorSoftwareVersion OBJECT-TYPE hdsl2ShdslInvVendorSoftwareVersion OBJECT-TYPE
SYNTAX DisplayString SYNTAX DisplayString
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Vendor software version as reported in an Inventory "Vendor software version as reported in an Inventory
Response message." Response message."
::= { hdsl2ShdslInventoryEntry 9 } ::= { hdsl2ShdslInventoryEntry 9 }
hdsl2ShdslInvEquipmentCode OBJECT-TYPE hdsl2ShdslInvEquipmentCode OBJECT-TYPE
SYNTAX DisplayString SYNTAX DisplayString
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Equipment code conforming to ANSI T1.213, Coded Identification "Equipment code conforming to ANSI T1.213, Coded Identification
of Equipment Entities." of Equipment Entities."
::= { hdsl2ShdslInventoryEntry 10 } ::= { hdsl2ShdslInventoryEntry 10 }
Expires November 8, 2000 Page [20]
hdsl2ShdslInvVendorOther OBJECT-TYPE hdsl2ShdslInvVendorOther OBJECT-TYPE
SYNTAX DisplayString SYNTAX DisplayString
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Other vendor information as reported in an Inventory "Other vendor information as reported in an Inventory
Response message." Response message."
::= { hdsl2ShdslInventoryEntry 11 } ::= { hdsl2ShdslInventoryEntry 11 }
hdsl2ShdslInvTransmissionModeCapability OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the transmission mode capability of the SHDSL unit."
::= { hdsl2ShdslInventoryEntry 12 }
-- Segment Endpoint Configuration Group -- Segment Endpoint Configuration Group
-- --
hdsl2ShdslEndpointConfTable OBJECT-TYPE hdsl2ShdslEndpointConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointConfEntry SYNTAX SEQUENCE OF Hdsl2ShdslEndpointConfEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table supports configuration parameters for segment "This table supports configuration parameters for segment
endpoints in a HDSL2/SHDSL line." endpoints in a HDSL2/SHDSL line."
skipping to change at line 1013 skipping to change at line 1126
DESCRIPTION DESCRIPTION
"An entry in the hdsl2ShdslEndpointConfTable. Each entry "An entry in the hdsl2ShdslEndpointConfTable. Each entry
represents a single segment endpoint in a HDSL2/SHDSL line. represents a single segment endpoint in a HDSL2/SHDSL line.
It is indexed by the ifIndex of the HDSL2/SHDSL line, the It is indexed by the ifIndex of the HDSL2/SHDSL line, the
UnitId of the associated unit, the side of the unit, and the UnitId of the associated unit, the side of the unit, and the
wire-pair of the associated modem." wire-pair of the associated modem."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair} hdsl2ShdslEndpointWirePair}
::= { hdsl2ShdslEndpointConfTable 1 } ::= { hdsl2ShdslEndpointConfTable 1 }
Expires November 8, 2000 Page [18]
Hdsl2ShdslEndpointConfEntry ::= Hdsl2ShdslEndpointConfEntry ::=
SEQUENCE SEQUENCE
{ {
hdsl2ShdslEndpointSide Hdsl2ShdslUnitSide, hdsl2ShdslEndpointSide Hdsl2ShdslUnitSide,
hdsl2ShdslEndpointWirePair Hdsl2ShdslWirePair, hdsl2ShdslEndpointWirePair Hdsl2ShdslWirePair,
hdsl2ShdslEndpointAlarmConfProfile SnmpAdminString hdsl2ShdslEndpointAlarmConfProfile SnmpAdminString
} }
hdsl2ShdslEndpointSide OBJECT-TYPE hdsl2ShdslEndpointSide OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitSide SYNTAX Hdsl2ShdslUnitSide
MAX-ACCESS read-only MAX-ACCESS read-only
Expires November 8, 2000 Page [21]
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The side of the unit associated with this segment endpoint - "The side of the unit associated with this segment endpoint -
Network/Customer side - as per the Hdsl2ShdslUnitSide Network/Customer side - as per the Hdsl2ShdslUnitSide
textual convention." textual convention."
::= { hdsl2ShdslEndpointConfEntry 1 } ::= { hdsl2ShdslEndpointConfEntry 1 }
hdsl2ShdslEndpointWirePair OBJECT-TYPE hdsl2ShdslEndpointWirePair OBJECT-TYPE
SYNTAX Hdsl2ShdslWirePair SYNTAX Hdsl2ShdslWirePair
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The wire-pair of the modem associated with this segment "The wire-pair of the modem associated with this segment
endpoint as per the Hdsl2ShdslWirePair textual convention." endpoint as per the Hdsl2ShdslWirePair textual convention."
::= { hdsl2ShdslEndpointConfEntry 2 } ::= { hdsl2ShdslEndpointConfEntry 2 }
hdsl2ShdslEndpointAlarmConfProfile OBJECT-TYPE hdsl2ShdslEndpointAlarmConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the alarm threshold values to be "This object configures the alarm threshold values to be
used for this segment endpoint. The values are obtained used for this segment endpoint. The values are obtained
from the alarm configuration profile referenced by this from the alarm configuration profile referenced by this
object. The value of this object is the index of the object. The value of this object is the index of the
referenced profile in the hdsl2ShdslLineAlarmConfProfileTable, referenced profile in the hdsl2ShdslLineAlarmConfProfileTable,
or NULL. If the value is NULL, the endpoint uses the or NULL. If the value is NULL, the endpoint uses the
default Alarm Configuration Profile for the associated default Alarm Configuration Profile for the associated
skipping to change at line 1071 skipping to change at line 1184
hdsl2ShdslEndpointCurrTable OBJECT-TYPE hdsl2ShdslEndpointCurrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointCurrEntry SYNTAX SEQUENCE OF Hdsl2ShdslEndpointCurrEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table contains current status and performance information "This table contains current status and performance information
for segment endpoints in HDSL2/SHDSL Lines." for segment endpoints in HDSL2/SHDSL Lines."
::= { hdsl2ShdslMibObjects 5 } ::= { hdsl2ShdslMibObjects 5 }
Expires November 8, 2000 Page [19]
hdsl2ShdslEndpointCurrEntry OBJECT-TYPE hdsl2ShdslEndpointCurrEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointCurrEntry SYNTAX Hdsl2ShdslEndpointCurrEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2ShdslEndpointCurrTable. Each entry "An entry in the hdsl2ShdslEndpointCurrTable. Each entry
contains status and performance information relating to a contains status and performance information relating to a
single segment endpoint. It is indexed by the ifIndex of single segment endpoint. It is indexed by the ifIndex of
the HDSL2/SHDSL line, the UnitId of the associated unit, the HDSL2/SHDSL line, the UnitId of the associated unit,
Expires November 8, 2000 Page [22]
the side of the unit, and the wire-pair of the associated the side of the unit, and the wire-pair of the associated
modem." modem."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair} hdsl2ShdslEndpointWirePair}
::= { hdsl2ShdslEndpointCurrTable 1 } ::= { hdsl2ShdslEndpointCurrTable 1 }
Hdsl2ShdslEndpointCurrEntry ::= Hdsl2ShdslEndpointCurrEntry ::=
SEQUENCE SEQUENCE
{ {
hdsl2ShdslEndpointCurrAtn Integer32, hdsl2ShdslEndpointCurrAtn Integer32,
skipping to change at line 1128 skipping to change at line 1241
DESCRIPTION DESCRIPTION
"The current loop attenuation for this endpoint as "The current loop attenuation for this endpoint as
reported in a Network or Customer Side Performance reported in a Network or Customer Side Performance
Status message." Status message."
::= { hdsl2ShdslEndpointCurrEntry 1 } ::= { hdsl2ShdslEndpointCurrEntry 1 }
hdsl2ShdslEndpointCurrSnrMgn OBJECT-TYPE hdsl2ShdslEndpointCurrSnrMgn OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
UNITS "dB" UNITS "dB"
MAX-ACCESS read-only MAX-ACCESS read-only
Expires November 8, 2000 Page [20]
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The current SNR margin for this endpoint as reported "The current SNR margin for this endpoint as reported
in a Status Response/SNR message." in a Status Response/SNR message."
::= { hdsl2ShdslEndpointCurrEntry 2 } ::= { hdsl2ShdslEndpointCurrEntry 2 }
hdsl2ShdslEndpointCurrStatus OBJECT-TYPE hdsl2ShdslEndpointCurrStatus OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
Expires November 8, 2000 Page [23]
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Contains the current state of the endpoint. This is a "Contains the current state of the endpoint. This is a
bit-map of possible conditions. The various bit positions bit-map of possible conditions. The various bit positions
are: are:
1 noDefect There no defects on the line 1 noDefect There no defects on the line
2 powerBackoff Indicates enhanced Power Backoff 2 powerBackoff Indicates enhanced Power Backoff
skipping to change at line 1184 skipping to change at line 1297
512 noNeighborPresent Endpoint failure during initialization 512 noNeighborPresent Endpoint failure during initialization
due to no activation sequence detected due to no activation sequence detected
from paired endpoint. from paired endpoint.
1024 loopbackActive A loopback is currently active at this 1024 loopbackActive A loopback is currently active at this
Segment Endpoint. Segment Endpoint.
This is intended to supplement ifOperStatus." This is intended to supplement ifOperStatus."
::= { hdsl2ShdslEndpointCurrEntry 3 } ::= { hdsl2ShdslEndpointCurrEntry 3 }
Expires November 8, 2000 Page [21]
hdsl2ShdslEndpointES OBJECT-TYPE hdsl2ShdslEndpointES OBJECT-TYPE
SYNTAX Counter32 SYNTAX Counter32
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Errored Seconds (ES) on this endpoint since the xU "Count of Errored Seconds (ES) on this endpoint since the xU
was last restarted." was last restarted."
Expires November 8, 2000 Page [24]
::= { hdsl2ShdslEndpointCurrEntry 4 } ::= { hdsl2ShdslEndpointCurrEntry 4 }
hdsl2ShdslEndpointSES OBJECT-TYPE hdsl2ShdslEndpointSES OBJECT-TYPE
SYNTAX Counter32 SYNTAX Counter32
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Severely Errored Seconds (SES) on this endpoint "Count of Severely Errored Seconds (SES) on this endpoint
since the xU was last restarted." since the xU was last restarted."
skipping to change at line 1241 skipping to change at line 1354
"Count of Unavailable Seconds (UAS) on this endpoint since "Count of Unavailable Seconds (UAS) on this endpoint since
the xU was last restarted." the xU was last restarted."
::= { hdsl2ShdslEndpointCurrEntry 8 } ::= { hdsl2ShdslEndpointCurrEntry 8 }
hdsl2ShdslEndpointCurr15MinTimeElapsed OBJECT-TYPE hdsl2ShdslEndpointCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
Expires November 8, 2000 Page [22]
"Total elapsed seconds in the current 15-minute interval." "Total elapsed seconds in the current 15-minute interval."
::= { hdsl2ShdslEndpointCurrEntry 9 } ::= { hdsl2ShdslEndpointCurrEntry 9 }
hdsl2ShdslEndpointCurr15MinES OBJECT-TYPE hdsl2ShdslEndpointCurr15MinES OBJECT-TYPE
SYNTAX PerfCurrentCount SYNTAX PerfCurrentCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
Expires November 8, 2000 Page [25]
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Errored Seconds (ES) in the current 15-minute "Count of Errored Seconds (ES) in the current 15-minute
interval." interval."
::= { hdsl2ShdslEndpointCurrEntry 10 } ::= { hdsl2ShdslEndpointCurrEntry 10 }
hdsl2ShdslEndpointCurr15MinSES OBJECT-TYPE hdsl2ShdslEndpointCurr15MinSES OBJECT-TYPE
SYNTAX PerfCurrentCount SYNTAX PerfCurrentCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
skipping to change at line 1298 skipping to change at line 1411
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Unavailable Seconds (UAS) in the current 15-minute "Count of Unavailable Seconds (UAS) in the current 15-minute
interval." interval."
::= { hdsl2ShdslEndpointCurrEntry 14 } ::= { hdsl2ShdslEndpointCurrEntry 14 }
hdsl2ShdslEndpointCurr1DayTimeElapsed OBJECT-TYPE hdsl2ShdslEndpointCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
Expires November 8, 2000 Page [23]
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Number of seconds that have elapsed since the beginning of "Number of seconds that have elapsed since the beginning of
the current 1-day interval." the current 1-day interval."
::= { hdsl2ShdslEndpointCurrEntry 15 } ::= { hdsl2ShdslEndpointCurrEntry 15 }
Expires November 8, 2000 Page [26]
hdsl2ShdslEndpointCurr1DayES OBJECT-TYPE hdsl2ShdslEndpointCurr1DayES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Errored Seconds (ES) during the current day as "Count of Errored Seconds (ES) during the current day as
measured by hdslPerfCurr1DayTimeElapsed." measured by hdslPerfCurr1DayTimeElapsed."
::= { hdsl2ShdslEndpointCurrEntry 16 } ::= { hdsl2ShdslEndpointCurrEntry 16 }
skipping to change at line 1355 skipping to change at line 1468
hdsl2ShdslEndpointCurr1DayUAS OBJECT-TYPE hdsl2ShdslEndpointCurr1DayUAS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Unavailable Seconds (UAS) during the current "Count of Unavailable Seconds (UAS) during the current
day as measured by hdslPerfCurr1DayTimeElapsed." day as measured by hdslPerfCurr1DayTimeElapsed."
::= { hdsl2ShdslEndpointCurrEntry 20 } ::= { hdsl2ShdslEndpointCurrEntry 20 }
Expires November 8, 2000 Page [24]
-- Segment Endpoint 15-Minute Interval Status/Performance Group -- Segment Endpoint 15-Minute Interval Status/Performance Group
-- --
hdsl2Shdsl15MinIntervalTable OBJECT-TYPE hdsl2Shdsl15MinIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2Shdsl15MinIntervalEntry SYNTAX SEQUENCE OF Hdsl2Shdsl15MinIntervalEntry
Expires November 8, 2000 Page [27]
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table provides one row for each HDSL2/SHDSL endpoint "This table provides one row for each HDSL2/SHDSL endpoint
performance data collection interval." performance data collection interval."
::= { hdsl2ShdslMibObjects 6 } ::= { hdsl2ShdslMibObjects 6 }
hdsl2Shdsl15MinIntervalEntry OBJECT-TYPE hdsl2Shdsl15MinIntervalEntry OBJECT-TYPE
SYNTAX Hdsl2Shdsl15MinIntervalEntry SYNTAX Hdsl2Shdsl15MinIntervalEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
skipping to change at line 1412 skipping to change at line 1525
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Errored Seconds (ES) during the interval." "Count of Errored Seconds (ES) during the interval."
::= { hdsl2Shdsl15MinIntervalEntry 2 } ::= { hdsl2Shdsl15MinIntervalEntry 2 }
hdsl2Shdsl15MinIntervalSES OBJECT-TYPE hdsl2Shdsl15MinIntervalSES OBJECT-TYPE
SYNTAX PerfIntervalCount SYNTAX PerfIntervalCount
UNITS "seconds" UNITS "seconds"
Expires November 8, 2000 Page [25]
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
Expires November 8, 2000 Page [28]
"Count of Severely Errored Seconds (SES) during the "Count of Severely Errored Seconds (SES) during the
interval." interval."
::= { hdsl2Shdsl15MinIntervalEntry 3 } ::= { hdsl2Shdsl15MinIntervalEntry 3 }
hdsl2Shdsl15MinIntervalCRCanomalies OBJECT-TYPE hdsl2Shdsl15MinIntervalCRCanomalies OBJECT-TYPE
SYNTAX PerfIntervalCount SYNTAX PerfIntervalCount
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of CRC anomalies during the interval." "Count of CRC anomalies during the interval."
skipping to change at line 1469 skipping to change at line 1582
hdsl2Shdsl1DayIntervalEntry OBJECT-TYPE hdsl2Shdsl1DayIntervalEntry OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalEntry SYNTAX Hdsl2Shdsl1DayIntervalEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2Shdsl1DayIntervalTable." "An entry in the hdsl2Shdsl1DayIntervalTable."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2Shdsl1DayIntervalInterval } hdsl2ShdslEndpointWirePair, hdsl2Shdsl1DayIntervalInterval }
::= { hdsl2Shdsl1DayIntervalTable 1 } ::= { hdsl2Shdsl1DayIntervalTable 1 }
Expires November 8, 2000 Page [26]
Hdsl2Shdsl1DayIntervalEntry ::= Hdsl2Shdsl1DayIntervalEntry ::=
SEQUENCE SEQUENCE
Expires November 8, 2000 Page [29]
{ {
hdsl2Shdsl1DayIntervalInterval INTEGER, hdsl2Shdsl1DayIntervalInterval INTEGER,
hdsl2Shdsl1DayIntervalMoniSecs Hdsl2ShdslPerfTimeElapsed, hdsl2Shdsl1DayIntervalMoniSecs Hdsl2ShdslPerfTimeElapsed,
hdsl2Shdsl1DayIntervalES Hdsl2Shdsl1DayIntervalCount, hdsl2Shdsl1DayIntervalES Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalSES Hdsl2Shdsl1DayIntervalCount, hdsl2Shdsl1DayIntervalSES Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalCRCanomalies Hdsl2Shdsl1DayIntervalCount, hdsl2Shdsl1DayIntervalCRCanomalies Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalLOSWS Hdsl2Shdsl1DayIntervalCount, hdsl2Shdsl1DayIntervalLOSWS Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalUAS Hdsl2Shdsl1DayIntervalCount hdsl2Shdsl1DayIntervalUAS Hdsl2Shdsl1DayIntervalCount
} }
skipping to change at line 1525 skipping to change at line 1638
hdsl2Shdsl1DayIntervalSES OBJECT-TYPE hdsl2Shdsl1DayIntervalSES OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Severely Errored Seconds (SES) during the 1-day "Count of Severely Errored Seconds (SES) during the 1-day
interval as measured by hdsl2Shdsl1DayIntervalMoniSecs." interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
::= { hdsl2Shdsl1DayIntervalEntry 4 } ::= { hdsl2Shdsl1DayIntervalEntry 4 }
Expires November 8, 2000 Page [27]
hdsl2Shdsl1DayIntervalCRCanomalies OBJECT-TYPE hdsl2Shdsl1DayIntervalCRCanomalies OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount SYNTAX Hdsl2Shdsl1DayIntervalCount
Expires November 8, 2000 Page [30]
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of CRC anomalies during the 1-day interval as "Count of CRC anomalies during the 1-day interval as
measured by hdsl2Shdsl1DayIntervalMoniSecs." measured by hdsl2Shdsl1DayIntervalMoniSecs."
::= { hdsl2Shdsl1DayIntervalEntry 5 } ::= { hdsl2Shdsl1DayIntervalEntry 5 }
hdsl2Shdsl1DayIntervalLOSWS OBJECT-TYPE hdsl2Shdsl1DayIntervalLOSWS OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds" UNITS "seconds"
skipping to change at line 1582 skipping to change at line 1695
"An entry in the hdsl2ShdslEndpointMaintTable. Each entry "An entry in the hdsl2ShdslEndpointMaintTable. Each entry
corresponds to a single segment endpoint, and is indexed by the corresponds to a single segment endpoint, and is indexed by the
ifIndex of the HDSL2/SHDSL line, the UnitId of the associated ifIndex of the HDSL2/SHDSL line, the UnitId of the associated
unit and the side of the unit." unit and the side of the unit."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide } INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide }
::= { hdsl2ShdslEndpointMaintTable 1 } ::= { hdsl2ShdslEndpointMaintTable 1 }
Hdsl2ShdslEndpointMaintEntry ::= Hdsl2ShdslEndpointMaintEntry ::=
SEQUENCE SEQUENCE
{ {
Expires November 8, 2000 Page [28]
hdsl2ShdslMaintLoopbackConfig INTEGER, hdsl2ShdslMaintLoopbackConfig INTEGER,
Expires November 8, 2000 Page [31]
hdsl2ShdslMaintTipRingReversal INTEGER, hdsl2ShdslMaintTipRingReversal INTEGER,
hdsl2ShdslMaintPowerBackOff INTEGER, hdsl2ShdslMaintPowerBackOff INTEGER,
hdsl2ShdslMaintSoftRestart INTEGER hdsl2ShdslMaintSoftRestart INTEGER
} }
hdsl2ShdslMaintLoopbackConfig OBJECT-TYPE hdsl2ShdslMaintLoopbackConfig OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
noLoopback(1), noLoopback(1),
normalLoopback(2), normalLoopback(2),
skipping to change at line 1640 skipping to change at line 1753
::= { hdsl2ShdslEndpointMaintEntry 3 } ::= { hdsl2ShdslEndpointMaintEntry 3 }
hdsl2ShdslMaintSoftRestart OBJECT-TYPE hdsl2ShdslMaintSoftRestart OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
ready(1), ready(1),
restart(2) restart(2)
} }
MAX-ACCESS read-write MAX-ACCESS read-write
Expires November 8, 2000 Page [29] Expires November 8, 2000 Page [32]
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object enables the manager to trigger a soft restart "This object enables the manager to trigger a soft restart
of the modem at the associated segment endpoint. The manager of the modem at the associated segment endpoint. The manager
may only set this object to the 'restart(2)' value to initiate may only set this object to the 'restart(2)' value to initiate
a restart. The agent will perform a restart after approximately a restart. The agent will perform a restart after approximately
5 seconds, and restore the object to the 'ready(1)' state." 5 seconds, and restore the object to the 'ready(1)' state."
::= { hdsl2ShdslEndpointMaintEntry 4 } ::= { hdsl2ShdslEndpointMaintEntry 4 }
hdsl2ShdslUnitMaintTable OBJECT-TYPE hdsl2ShdslUnitMaintTable OBJECT-TYPE
skipping to change at line 1695 skipping to change at line 1808
unit. A value of 0 disables the timeout." unit. A value of 0 disables the timeout."
::= { hdsl2ShdslUnitMaintEntry 1 } ::= { hdsl2ShdslUnitMaintEntry 1 }
hdsl2ShdslMaintUnitPowerSource OBJECT-TYPE hdsl2ShdslMaintUnitPowerSource OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
local(1), local(1),
span(2) span(2)
} }
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current
Expires November 8, 2000 Page [30] Expires November 8, 2000 Page [33]
STATUS current
DESCRIPTION DESCRIPTION
"This object indicates the DC power source being used by the "This object indicates the DC power source being used by the
associated unit." associated unit."
::= { hdsl2ShdslUnitMaintEntry 2 } ::= { hdsl2ShdslUnitMaintEntry 2 }
-- Span Configuration Profile Group -- Span Configuration Profile Group
-- --
hdsl2ShdslSpanConfProfileTable OBJECT-TYPE hdsl2ShdslSpanConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfProfileEntry SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfProfileEntry
skipping to change at line 1729 skipping to change at line 1842
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Each entry corresponds to a single span configuration "Each entry corresponds to a single span configuration
profile. Each profile contains a set of span configuration profile. Each profile contains a set of span configuration
parameters. The configuration parameters in a profile are parameters. The configuration parameters in a profile are
applied to those lines referencing that profile (see the applied to those lines referencing that profile (see the
hdsl2ShdslSpanConfProfile object). Profiles may be hdsl2ShdslSpanConfProfile object). Profiles may be
created/deleted using the row creation/deletion mechanism created/deleted using the row creation/deletion mechanism
via hdsl2ShdslSpanConfProfileRowStatus. Profiles that are via hdsl2ShdslSpanConfProfileRowStatus. Profiles that are
being referenced may not be deleted." being referenced may not be deleted."
INDEX { hdsl2ShdslSpanConfProfileName } INDEX { IMPLIED hdsl2ShdslSpanConfProfileName }
::= { hdsl2ShdslSpanConfProfileTable 1 } ::= { hdsl2ShdslSpanConfProfileTable 1 }
Hdsl2ShdslSpanConfProfileEntry ::= Hdsl2ShdslSpanConfProfileEntry ::=
SEQUENCE SEQUENCE
{ {
hdsl2ShdslSpanConfProfileName SnmpAdminString, hdsl2ShdslSpanConfProfileName SnmpAdminString,
hdsl2ShdslSpanWireInterface INTEGER, hdsl2ShdslSpanWireInterface INTEGER,
hdsl2ShdslSpanLineSpeed Integer32, hdsl2ShdslSpanMinLineRate Integer32,
hdsl2ShdslSpanMaxLineRate Integer32,
hdsl2ShdslSpanConfPSD INTEGER, hdsl2ShdslSpanConfPSD INTEGER,
hdsl2ShdslSpanConfTransmissionMode Hdsl2ShdslTransmissionModeType,
hdsl2ShdslSpanRemoteEnabled INTEGER, hdsl2ShdslSpanRemoteEnabled INTEGER,
hdsl2ShdslSpanPowerFeeding INTEGER,
hdsl2ShdslSpanConfProfileRowStatus RowStatus hdsl2ShdslSpanConfProfileRowStatus RowStatus
} }
hdsl2ShdslSpanConfProfileName OBJECT-TYPE hdsl2ShdslSpanConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-create MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
Expires November 8, 2000 Page [34]
"This object is the unique index associated with this profile." "This object is the unique index associated with this profile."
::= { hdsl2ShdslSpanConfProfileEntry 1 } ::= { hdsl2ShdslSpanConfProfileEntry 1 }
hdsl2ShdslSpanWireInterface OBJECT-TYPE hdsl2ShdslSpanWireInterface OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
Expires November 8, 2000 Page [31]
{ {
twoWire(1), twoWire(1),
fourWire(2) fourWire(2)
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the two-wire or optional four-wire "This object configures the two-wire or optional four-wire
operation for SHDSL Lines." operation for SHDSL Lines."
::= { hdsl2ShdslSpanConfProfileEntry 2 } ::= { hdsl2ShdslSpanConfProfileEntry 2 }
hdsl2ShdslSpanLineSpeed OBJECT-TYPE hdsl2ShdslSpanMinLineRate OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
UNITS "bps" UNITS "bps"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the transmission rate for the associated "This object configures the minimum transmission rate for
SHDSL Line in bits-per-second (bps)." the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'."
::= { hdsl2ShdslSpanConfProfileEntry 3 } ::= { hdsl2ShdslSpanConfProfileEntry 3 }
hdsl2ShdslSpanMaxLineRate OBJECT-TYPE
SYNTAX Integer32
UNITS "bps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'."
::= { hdsl2ShdslSpanConfProfileEntry 4 }
hdsl2ShdslSpanConfPSD OBJECT-TYPE hdsl2ShdslSpanConfPSD OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
symmetric(1), symmetric(1),
asymmetric(2) asymmetric(2)
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures use of symmetric/asymmetric PSD (Power "This object configures use of symmetric/asymmetric PSD (Power
Expires November 8, 2000 Page [35]
Spectral Density) Mask for the associated SHDSL Line. Support Spectral Density) Mask for the associated SHDSL Line. Support
for symmetric PSD is mandatory for all supported data rates. for symmetric PSD is mandatory for all supported data rates.
Support for asymmetric PSD is optional." Support for asymmetric PSD is optional."
::= { hdsl2ShdslSpanConfProfileEntry 4 } ::= { hdsl2ShdslSpanConfProfileEntry 5 }
hdsl2ShdslSpanConfTransmissionMode OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the regional setting for the SHDSL
line."
::= { hdsl2ShdslSpanConfProfileEntry 6 }
hdsl2ShdslSpanRemoteEnabled OBJECT-TYPE hdsl2ShdslSpanRemoteEnabled OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
enabled(1), enabled(1),
disabled(2) disabled(2)
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object enables/disables support for remote management "This object enables/disables support for remote management
of the units in a SHDSL line from the STU-R via the EOC." of the units in a SHDSL line from the STU-R via the EOC."
::= { hdsl2ShdslSpanConfProfileEntry 5 } ::= { hdsl2ShdslSpanConfProfileEntry 7 }
hdsl2ShdslSpanPowerFeeding OBJECT-TYPE
SYNTAX INTEGER
{
noPower(1),
powerFeed(2),
wettingCurrent(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object enables/disables support for optional power
feeding in a SHDSL line."
::= { hdsl2ShdslSpanConfProfileEntry 8 }
hdsl2ShdslSpanConfProfileRowStatus OBJECT-TYPE hdsl2ShdslSpanConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus SYNTAX RowStatus
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object controlls creation/deletion of the associated "This object controlls creation/deletion of the associated
Expires November 8, 2000 Page [32]
entry in this table per the semantics of RowStatus." entry in this table per the semantics of RowStatus."
::= { hdsl2ShdslSpanConfProfileEntry 6 } ::= { hdsl2ShdslSpanConfProfileEntry 9 }
-- Segment Endpoint Alarm Configuration Profile group -- Segment Endpoint Alarm Configuration Profile group
-- --
hdsl2ShdslEndpointAlarmConfProfileTable OBJECT-TYPE hdsl2ShdslEndpointAlarmConfProfileTable OBJECT-TYPE
Expires November 8, 2000 Page [36]
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointAlarmConfProfileEntry SYNTAX SEQUENCE OF Hdsl2ShdslEndpointAlarmConfProfileEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table supports definitions of alarm configuration "This table supports definitions of alarm configuration
profiles for HDSL2/SHDSL segment endoints." profiles for HDSL2/SHDSL segment endoints."
::= { hdsl2ShdslMibObjects 11 } ::= { hdsl2ShdslMibObjects 11 }
hdsl2ShdslEndpointAlarmConfProfileEntry OBJECT-TYPE hdsl2ShdslEndpointAlarmConfProfileEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointAlarmConfProfileEntry SYNTAX Hdsl2ShdslEndpointAlarmConfProfileEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Each entry corresponds to a single alarm configuration "Each entry corresponds to a single alarm configuration
profile. Each profile contains a set of parameters for setting profile. Each profile contains a set of parameters for setting
alarm thresholds for various performance attributes monitored alarm thresholds for various performance attributes monitored
at HDSL2/SHDSL segment endpoints. Profiles may be at HDSL2/SHDSL segment endpoints. Profiles may be
created/deleted using the row creation/deletion mechanism via created/deleted using the row creation/deletion mechanism via
hdsl2ShdslEndpointAlarmConfProfileRowStatus. Profiles that hdsl2ShdslEndpointAlarmConfProfileRowStatus. Profiles that
are being referenced may not be deleted." are being referenced may not be deleted."
INDEX { hdsl2ShdslEndpointAlarmConfProfileName } INDEX { IMPLIED hdsl2ShdslEndpointAlarmConfProfileName }
::= { hdsl2ShdslEndpointAlarmConfProfileTable 1 } ::= { hdsl2ShdslEndpointAlarmConfProfileTable 1 }
Hdsl2ShdslEndpointAlarmConfProfileEntry ::= Hdsl2ShdslEndpointAlarmConfProfileEntry ::=
SEQUENCE SEQUENCE
{ {
hdsl2ShdslEndpointAlarmConfProfileName SnmpAdminString, hdsl2ShdslEndpointAlarmConfProfileName SnmpAdminString,
hdsl2ShdslEndpointThreshLoopAttenuation Integer32, hdsl2ShdslEndpointThreshLoopAttenuation Integer32,
hdsl2ShdslEndpointThreshSNRMargin Integer32, hdsl2ShdslEndpointThreshSNRMargin Integer32,
hdsl2ShdslEndpointThreshES hdsl2ShdslEndpointThreshES
Hdsl2ShdslPerfIntervalThreshold, Hdsl2ShdslPerfIntervalThreshold,
skipping to change at line 1861 skipping to change at line 2020
Hdsl2ShdslPerfIntervalThreshold, Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshCRCanomalies Integer32, hdsl2ShdslEndpointThreshCRCanomalies Integer32,
hdsl2ShdslEndpointThreshLOSWS hdsl2ShdslEndpointThreshLOSWS
Hdsl2ShdslPerfIntervalThreshold, Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshUAS hdsl2ShdslEndpointThreshUAS
Hdsl2ShdslPerfIntervalThreshold, Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointAlarmConfProfileRowStatus RowStatus hdsl2ShdslEndpointAlarmConfProfileRowStatus RowStatus
} }
hdsl2ShdslEndpointAlarmConfProfileName OBJECT-TYPE hdsl2ShdslEndpointAlarmConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-create MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is the unique index associated with this profile." "This object is the unique index associated with this profile."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 1 } ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 1 }
Expires November 8, 2000 Page [33]
hdsl2ShdslEndpointThreshLoopAttenuation OBJECT-TYPE hdsl2ShdslEndpointThreshLoopAttenuation OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
UNITS "dB" UNITS "dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
Expires November 8, 2000 Page [37]
DESCRIPTION DESCRIPTION
"This object configures the loop attentuation alarm threshold. "This object configures the loop attentuation alarm threshold.
When the current value reaches/exceeds this threshold, a When the current value reaches/exceeds this threshold, a
hdsl2ShdslLoopAttenCrossingTrap will be generated." hdsl2ShdslLoopAttenCrossingTrap will be generated."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 2 } ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 2 }
hdsl2ShdslEndpointThreshSNRMargin OBJECT-TYPE hdsl2ShdslEndpointThreshSNRMargin OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
UNITS "dB" UNITS "dB"
MAX-ACCESS read-create MAX-ACCESS read-create
skipping to change at line 1925 skipping to change at line 2084
performance data collection interval. If the value of severely performance data collection interval. If the value of severely
errored seconds in a particular 15-minute collection interval errored seconds in a particular 15-minute collection interval
reaches/exceeds this value, a hdsl2ShdslPerfSESThreshTrap will reaches/exceeds this value, a hdsl2ShdslPerfSESThreshTrap will
be generated. One trap will be sent per interval per endpoint." be generated. One trap will be sent per interval per endpoint."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 5 } ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 5 }
hdsl2ShdslEndpointThreshCRCanomalies OBJECT-TYPE hdsl2ShdslEndpointThreshCRCanomalies OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
Expires November 8, 2000 Page [34]
DESCRIPTION DESCRIPTION
"This object configures the threshold for the number of "This object configures the threshold for the number of
CRC anomalies within any given 15-minute performance data CRC anomalies within any given 15-minute performance data
collection interval. If the value of CRC anomalies in a collection interval. If the value of CRC anomalies in a
Expires November 8, 2000 Page [38]
particular 15-minute collection interval reaches/exceeds particular 15-minute collection interval reaches/exceeds
this value, a hdsl2ShdslPerfCRCanomaliesThreshTrap will be this value, a hdsl2ShdslPerfCRCanomaliesThreshTrap will be
generated. One trap will be sent per interval per endpoint." generated. One trap will be sent per interval per endpoint."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 6 } ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 6 }
hdsl2ShdslEndpointThreshLOSWS OBJECT-TYPE hdsl2ShdslEndpointThreshLOSWS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
skipping to change at line 1982 skipping to change at line 2141
-- Notifications Group -- Notifications Group
-- --
hdsl2ShdslTraps OBJECT IDENTIFIER ::= { hdsl2ShdslLineMib 2 } hdsl2ShdslTraps OBJECT IDENTIFIER ::= { hdsl2ShdslLineMib 2 }
hdsl2ShdslTrapsPrefix OBJECT IDENTIFIER ::= { hdsl2ShdslTraps 0 } hdsl2ShdslTrapsPrefix OBJECT IDENTIFIER ::= { hdsl2ShdslTraps 0 }
hdsl2ShdslLoopAttenCrossingTrap NOTIFICATION-TYPE hdsl2ShdslLoopAttenCrossingTrap NOTIFICATION-TYPE
OBJECTS OBJECTS
{ {
Expires November 8, 2000 Page [35]
ifIndex, ifIndex,
hdsl2ShdslInvIndex, hdsl2ShdslInvIndex,
hdsl2ShdslEndpointSide, hdsl2ShdslEndpointSide,
Expires November 8, 2000 Page [39]
hdsl2ShdslEndpointWirePair, hdsl2ShdslEndpointWirePair,
hdsl2ShdslEndpointCurrAtn, hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointThreshLoopAttenuation hdsl2ShdslEndpointThreshLoopAttenuation
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This trap indicates that the loop attenuation threshold (as "This trap indicates that the loop attenuation threshold (as
per the hdsl2ShdslEndpointThreshLoopAttenuation value) has been per the hdsl2ShdslEndpointThreshLoopAttenuation value) has been
reached/exceeded for the HDSL2/SHDSL segment endpoint identified reached/exceeded for the HDSL2/SHDSL segment endpoint identified
by the ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, and by the ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, and
skipping to change at line 2038 skipping to change at line 2197
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This trap indicates that the errored seconds threshold (as "This trap indicates that the errored seconds threshold (as
per the hdsl2ShdslEndpointThreshES value) has been reached/ per the hdsl2ShdslEndpointThreshES value) has been reached/
exceeded for the HDSL2/SHDSL segment endpoint identified by the exceeded for the HDSL2/SHDSL segment endpoint identified by the
ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, and ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, and
hdsl2ShdslEndpointWirePair values." hdsl2ShdslEndpointWirePair values."
::= { hdsl2ShdslTrapsPrefix 3 } ::= { hdsl2ShdslTrapsPrefix 3 }
Expires November 8, 2000 Page [36]
hdsl2ShdslPerfSESThreshTrap NOTIFICATION-TYPE hdsl2ShdslPerfSESThreshTrap NOTIFICATION-TYPE
OBJECTS OBJECTS
{ {
Expires November 8, 2000 Page [40]
ifIndex, ifIndex,
hdsl2ShdslInvIndex, hdsl2ShdslInvIndex,
hdsl2ShdslEndpointSide, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2ShdslEndpointWirePair,
hdsl2ShdslEndpointCurr15MinSES, hdsl2ShdslEndpointCurr15MinSES,
hdsl2ShdslEndpointThreshSES hdsl2ShdslEndpointThreshSES
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This trap indicates that the severely errored seconds threshold "This trap indicates that the severely errored seconds threshold
skipping to change at line 2095 skipping to change at line 2254
hdsl2ShdslEndpointCurr15MinLOSWS, hdsl2ShdslEndpointCurr15MinLOSWS,
hdsl2ShdslEndpointThreshLOSWS hdsl2ShdslEndpointThreshLOSWS
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This trap indicates that the LOSW seconds threshold (as per the "This trap indicates that the LOSW seconds threshold (as per the
hdsl2ShdslEndpointThreshLOSWS value) has been reached/exceeded hdsl2ShdslEndpointThreshLOSWS value) has been reached/exceeded
for the HDSL2/SHDSL segment endpoint identified by the ifIndex, for the HDSL2/SHDSL segment endpoint identified by the ifIndex,
hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, and hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, and
hdsl2ShdslEndpointWirePair values." hdsl2ShdslEndpointWirePair values."
Expires November 8, 2000 Page [37]
::= { hdsl2ShdslTrapsPrefix 6 } ::= { hdsl2ShdslTrapsPrefix 6 }
Expires November 8, 2000 Page [41]
hdsl2ShdslPerfUASThreshTrap NOTIFICATION-TYPE hdsl2ShdslPerfUASThreshTrap NOTIFICATION-TYPE
OBJECTS OBJECTS
{ {
ifIndex, ifIndex,
hdsl2ShdslInvIndex, hdsl2ShdslInvIndex,
hdsl2ShdslEndpointSide, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2ShdslEndpointWirePair,
hdsl2ShdslEndpointCurr15MinUAS, hdsl2ShdslEndpointCurr15MinUAS,
hdsl2ShdslEndpointThreshUAS hdsl2ShdslEndpointThreshUAS
} }
skipping to change at line 2133 skipping to change at line 2292
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This trap indicates that a mismatch has been detected between "This trap indicates that a mismatch has been detected between
the number of repeater/regenerator units configured for a the number of repeater/regenerator units configured for a
HDSL2/SHDSL line via the hdsl2ShdslConfNumRepeaters object and HDSL2/SHDSL line via the hdsl2ShdslConfNumRepeaters object and
the actual number of repeater/regenerator units discovered via the actual number of repeater/regenerator units discovered via
the EOC." the EOC."
::= { hdsl2ShdslTrapsPrefix 8 } ::= { hdsl2ShdslTrapsPrefix 8 }
hdsl2ShdslLoopbackFailure NOTIFICATION-TYPE
OBJECTS
{
ifIndex,
hdsl2ShdslInvIndex,
hdsl2ShdslEndpointSide,
hdsl2ShdslMaintLoopbackConfig
}
STATUS current
DESCRIPTION
"This trap indicates that an endpoint maintenance loopback
command failed for an HDSL2/SHDSL segment."
::= { hdsl2ShdslTrapsPrefix 9 }
-- conformance information -- conformance information
--
hdsl2ShdslConformance OBJECT IDENTIFIER ::= { hdsl2ShdslLineMib 3 } hdsl2ShdslConformance OBJECT IDENTIFIER ::= { hdsl2ShdslLineMib 3 }
hdsl2ShdslGroups OBJECT IDENTIFIER ::= { hdsl2ShdslConformance 1 } hdsl2ShdslGroups OBJECT IDENTIFIER ::= { hdsl2ShdslConformance 1 }
hdsl2ShdslCompliances OBJECT IDENTIFIER ::= { hdsl2ShdslConformance 2 } hdsl2ShdslCompliances OBJECT IDENTIFIER ::= { hdsl2ShdslConformance 2 }
Expires November 8, 2000 Page [42]
-- agent compliance statements -- agent compliance statements
hdsl2ShdslLineMibCompliance MODULE-COMPLIANCE hdsl2ShdslLineMibCompliance MODULE-COMPLIANCE
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The section outlines compliance requirements for this MIB." "The section outlines compliance requirements for this MIB."
MODULE MODULE
MANDATORY-GROUPS MANDATORY-GROUPS
{ {
hdsl2ShdslSpanConfGroup, hdsl2ShdslSpanConfGroup,
hdsl2ShdslSpanStatusGroup,
hdsl2ShdslInventoryGroup, hdsl2ShdslInventoryGroup,
hdsl2ShdslEndpointConfGroup, hdsl2ShdslEndpointConfGroup,
hdsl2ShdslEndpointCurrGroup, hdsl2ShdslEndpointCurrGroup,
Expires November 8, 2000 Page [38]
hdsl2Shdsl15MinIntervalGroup, hdsl2Shdsl15MinIntervalGroup,
hdsl2Shdsl1DayIntervalGroup, hdsl2Shdsl1DayIntervalGroup,
hdsl2ShdslMaintenanceGroup, hdsl2ShdslMaintenanceGroup,
hdsl2ShdslEndpointAlarmConfGroup, hdsl2ShdslEndpointAlarmConfGroup,
hdsl2ShdslNotificationGroup hdsl2ShdslNotificationGroup
} }
GROUP hdsl2ShdslInventoryShdslGroup
DESCRIPTION
"Support for this group is only required for implementations
supporting SHDSL lines."
GROUP hdsl2ShdslSpanShdslStatusGroup
DESCRIPTION
"Support for this group is only required for implementations
supporting SHDSL lines."
GROUP hdsl2ShdslSpanConfProfileGroup GROUP hdsl2ShdslSpanConfProfileGroup
DESCRIPTION DESCRIPTION
"Support for this group is only required for implementations "Support for this group is only required for implementations
supporting SHDSL lines." supporting SHDSL lines."
::= { hdsl2ShdslCompliances 1 } ::= { hdsl2ShdslCompliances 1 }
-- units of conformance -- units of conformance
--
hdsl2ShdslSpanConfGroup OBJECT-GROUP hdsl2ShdslSpanConfGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
hdsl2ShdslConfNumRepeaters, hdsl2ShdslConfNumRepeaters,
hdsl2ShdslSpanConfProfile, hdsl2ShdslSpanConfProfile,
hdsl2ShdslSpanAlarmConfProfile hdsl2ShdslSpanAlarmConfProfile
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects for configuring span related "This group supports objects for configuring span related
parameters for HDSL2/SHDSL lines." parameters for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 1 } ::= { hdsl2ShdslGroups 1 }
Expires November 8, 2000 Page [43]
hdsl2ShdslSpanStatusGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslStatusNumAvailRepeaters
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving span related
status for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 2 }
hdsl2ShdslInventoryShdslGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslInvTransmissionModeCapability
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving SHDSL-specific
inventory information."
::= { hdsl2ShdslGroups 3 }
hdsl2ShdslSpanShdslStatusGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslStatusMaxAttainableLineRate,
hdsl2ShdslStatusActualLineRate,
hdsl2ShdslStatusTransmissionModeCurrent
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving SHDSL-specific
span related status."
::= { hdsl2ShdslGroups 4 }
hdsl2ShdslInventoryGroup OBJECT-GROUP hdsl2ShdslInventoryGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
hdsl2ShdslInvIndex, hdsl2ShdslInvIndex,
hdsl2ShdslInvVendorID, hdsl2ShdslInvVendorID,
hdsl2ShdslInvVendorModelNumber, hdsl2ShdslInvVendorModelNumber,
hdsl2ShdslInvVendorSerialNumber, hdsl2ShdslInvVendorSerialNumber,
hdsl2ShdslInvVendorEOCSoftwareVersion, hdsl2ShdslInvVendorEOCSoftwareVersion,
hdsl2ShdslInvStandardVersion, hdsl2ShdslInvStandardVersion,
hdsl2ShdslInvVendorListNumber, hdsl2ShdslInvVendorListNumber,
hdsl2ShdslInvVendorIssueNumber, hdsl2ShdslInvVendorIssueNumber,
hdsl2ShdslInvVendorSoftwareVersion, hdsl2ShdslInvVendorSoftwareVersion,
hdsl2ShdslInvEquipmentCode, hdsl2ShdslInvEquipmentCode,
hdsl2ShdslInvVendorOther hdsl2ShdslInvVendorOther
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects that provide unit inventory "This group supports objects that provide unit inventory
information about the units in HDSL2/SHDSL lines." information about the units in HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 2 }
Expires November 8, 2000 Page [44]
::= { hdsl2ShdslGroups 5 }
hdsl2ShdslEndpointConfGroup OBJECT-GROUP hdsl2ShdslEndpointConfGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
hdsl2ShdslEndpointSide, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2ShdslEndpointWirePair,
Expires November 8, 2000 Page [39]
hdsl2ShdslEndpointAlarmConfProfile hdsl2ShdslEndpointAlarmConfProfile
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects for configuring parameters for "This group supports objects for configuring parameters for
segment endpoints in HDSL2/SHDSL lines." segment endpoints in HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 3 } ::= { hdsl2ShdslGroups 6 }
hdsl2ShdslEndpointCurrGroup OBJECT-GROUP hdsl2ShdslEndpointCurrGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
hdsl2ShdslEndpointSide, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2ShdslEndpointWirePair,
hdsl2ShdslEndpointCurrAtn, hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointCurrSnrMgn, hdsl2ShdslEndpointCurrSnrMgn,
hdsl2ShdslEndpointCurrStatus, hdsl2ShdslEndpointCurrStatus,
hdsl2ShdslEndpointES, hdsl2ShdslEndpointES,
skipping to change at line 2250 skipping to change at line 2473
hdsl2ShdslEndpointCurr1DaySES, hdsl2ShdslEndpointCurr1DaySES,
hdsl2ShdslEndpointCurr1DayCRCanomalies, hdsl2ShdslEndpointCurr1DayCRCanomalies,
hdsl2ShdslEndpointCurr1DayLOSWS, hdsl2ShdslEndpointCurr1DayLOSWS,
hdsl2ShdslEndpointCurr1DayUAS hdsl2ShdslEndpointCurr1DayUAS
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects which provide current status and "This group supports objects which provide current status and
performance measurements relating to segment endpoints in performance measurements relating to segment endpoints in
HDSL2/SHDSL lines." HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 4 } ::= { hdsl2ShdslGroups 7 }
hdsl2Shdsl15MinIntervalGroup OBJECT-GROUP hdsl2Shdsl15MinIntervalGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
hdsl2Shdsl15MinIntervalES, hdsl2Shdsl15MinIntervalES,
hdsl2Shdsl15MinIntervalSES, hdsl2Shdsl15MinIntervalSES,
hdsl2Shdsl15MinIntervalCRCanomalies, hdsl2Shdsl15MinIntervalCRCanomalies,
Expires November 8, 2000 Page [45]
hdsl2Shdsl15MinIntervalLOSWS, hdsl2Shdsl15MinIntervalLOSWS,
hdsl2Shdsl15MinIntervalUAS hdsl2Shdsl15MinIntervalUAS
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects which maintain historic performance "This group supports objects which maintain historic performance
measurements relating to segment endpoints in HDSL2/SHDSL lines measurements relating to segment endpoints in HDSL2/SHDSL lines
in 15-minute intervals." in 15-minute intervals."
::= { hdsl2ShdslGroups 8 }
Expires November 8, 2000 Page [40]
::= { hdsl2ShdslGroups 5 }
hdsl2Shdsl1DayIntervalGroup OBJECT-GROUP hdsl2Shdsl1DayIntervalGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
hdsl2Shdsl1DayIntervalMoniSecs, hdsl2Shdsl1DayIntervalMoniSecs,
hdsl2Shdsl1DayIntervalES, hdsl2Shdsl1DayIntervalES,
hdsl2Shdsl1DayIntervalSES, hdsl2Shdsl1DayIntervalSES,
hdsl2Shdsl1DayIntervalCRCanomalies, hdsl2Shdsl1DayIntervalCRCanomalies,
hdsl2Shdsl1DayIntervalLOSWS, hdsl2Shdsl1DayIntervalLOSWS,
hdsl2Shdsl1DayIntervalUAS hdsl2Shdsl1DayIntervalUAS
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects which maintain historic performance "This group supports objects which maintain historic performance
measurements relating to segment endpoints in HDSL2/SHDSL lines measurements relating to segment endpoints in HDSL2/SHDSL lines
in 1-day intervals." in 1-day intervals."
::= { hdsl2ShdslGroups 6 } ::= { hdsl2ShdslGroups 9 }
hdsl2ShdslMaintenanceGroup OBJECT-GROUP hdsl2ShdslMaintenanceGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
hdsl2ShdslMaintLoopbackConfig, hdsl2ShdslMaintLoopbackConfig,
hdsl2ShdslMaintTipRingReversal, hdsl2ShdslMaintTipRingReversal,
hdsl2ShdslMaintPowerBackOff, hdsl2ShdslMaintPowerBackOff,
hdsl2ShdslMaintSoftRestart, hdsl2ShdslMaintSoftRestart,
hdsl2ShdslMaintLoopbackTimeout, hdsl2ShdslMaintLoopbackTimeout,
hdsl2ShdslMaintUnitPowerSource hdsl2ShdslMaintUnitPowerSource
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects that provide support for "This group supports objects that provide support for
maintenance actions for HDSL2/SHDSL lines." maintenance actions for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 7 } ::= { hdsl2ShdslGroups 10 }
hdsl2ShdslEndpointAlarmConfGroup OBJECT-GROUP hdsl2ShdslEndpointAlarmConfGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
hdsl2ShdslEndpointAlarmConfProfileName,
hdsl2ShdslEndpointThreshLoopAttenuation, hdsl2ShdslEndpointThreshLoopAttenuation,
hdsl2ShdslSpanWireInterface, hdsl2ShdslSpanWireInterface,
hdsl2ShdslEndpointThreshSNRMargin, hdsl2ShdslEndpointThreshSNRMargin,
hdsl2ShdslEndpointThreshES, hdsl2ShdslEndpointThreshES,
hdsl2ShdslEndpointThreshSES, hdsl2ShdslEndpointThreshSES,
hdsl2ShdslEndpointThreshCRCanomalies, hdsl2ShdslEndpointThreshCRCanomalies,
hdsl2ShdslEndpointThreshLOSWS, hdsl2ShdslEndpointThreshLOSWS,
hdsl2ShdslEndpointThreshUAS, hdsl2ShdslEndpointThreshUAS,
Expires November 8, 2000 Page [46]
hdsl2ShdslEndpointAlarmConfProfileRowStatus hdsl2ShdslEndpointAlarmConfProfileRowStatus
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects that allow configuration of alarm "This group supports objects that allow configuration of alarm
thresholds for various performance parameters for HDSL2/SHDSL thresholds for various performance parameters for HDSL2/SHDSL
lines." lines."
::= { hdsl2ShdslGroups 8 } ::= { hdsl2ShdslGroups 11 }
Expires November 8, 2000 Page [41]
hdsl2ShdslNotificationGroup NOTIFICATION-GROUP hdsl2ShdslNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS NOTIFICATIONS
{ {
hdsl2ShdslLoopAttenCrossingTrap, hdsl2ShdslLoopAttenCrossingTrap,
hdsl2ShdslSNRMarginCrossingTrap, hdsl2ShdslSNRMarginCrossingTrap,
hdsl2ShdslPerfESThreshTrap, hdsl2ShdslPerfESThreshTrap,
hdsl2ShdslPerfSESThreshTrap, hdsl2ShdslPerfSESThreshTrap,
hdsl2ShdslPerfCRCanomaliesThreshTrap, hdsl2ShdslPerfCRCanomaliesThreshTrap,
hdsl2ShdslPerfLOSWSThreshTrap, hdsl2ShdslPerfLOSWSThreshTrap,
hdsl2ShdslPerfUASThreshTrap, hdsl2ShdslPerfUASThreshTrap,
hdsl2ShdslSpanInvalidNumRepeaters hdsl2ShdslSpanInvalidNumRepeaters,
hdsl2ShdslLoopbackFailure
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports traps that enable notification of "This group supports traps that enable notification of
significant events/conditions associated with HDSL2/SHDSL significant events/conditions associated with HDSL2/SHDSL
lines." lines."
::= { hdsl2ShdslGroups 9 } ::= { hdsl2ShdslGroups 12 }
hdsl2ShdslSpanConfProfileGroup OBJECT-GROUP hdsl2ShdslSpanConfProfileGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
hdsl2ShdslSpanConfProfileName,
hdsl2ShdslSpanWireInterface, hdsl2ShdslSpanWireInterface,
hdsl2ShdslSpanLineSpeed, hdsl2ShdslSpanMinLineRate,
hdsl2ShdslSpanRemoteEnabled, hdsl2ShdslSpanMaxLineRate,
hdsl2ShdslSpanConfPSD, hdsl2ShdslSpanConfPSD,
hdsl2ShdslSpanConfTransmissionMode,
hdsl2ShdslSpanRemoteEnabled,
hdsl2ShdslSpanPowerFeeding,
hdsl2ShdslSpanConfProfileRowStatus hdsl2ShdslSpanConfProfileRowStatus
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects that constitute configuration "This group supports objects that constitute configuration
profiles for configuring span related parameters in SHDSL profiles for configuring span related parameters in SHDSL
lines." lines."
::= { hdsl2ShdslGroups 10 } ::= { hdsl2ShdslGroups 13 }
END END
7. Security Considerations 7. Security Considerations
Security issues are not discussed in this memo. Security issues are not discussed in this memo.
Expires November 8, 2000 Page [47]
8. Acknowledgments 8. Acknowledgments
The authors are deeply grateful to the authors of the ADSL LINE MIB The authors are deeply grateful to the authors of the ADSL LINE MIB
(RFC 2662 [25]), Gregory Bathrick and Faye Ly, as much of the text (RFC 2662 [25]), Gregory Bathrick and Faye Ly, as much of the text
and structure of this document originates in their documents. and structure of this document originates in their documents.
The authors also acknowledge the importance of contributions and The authors also acknowledge the importance of contributions and
suggestions regarding interface indexing structures received from suggestions regarding interface indexing structures received from
David Horton of CITR. David Horton of CITR.
Other contributions were received from the following: Other contributions were received from the following:
Philip Bergstresser (Adtran) Philip Bergstresser (Adtran)
Expires November 8, 2000 Page [42]
Steve Blackwell (Adtran) Steve Blackwell (Adtran)
Mark Johnson (Red Point) Mark Johnson (Red Point)
Sharon Mantin (Orckit) Sharon Mantin (Orckit)
Moti Morgenstern (ECI)
Raymond Murphy (Ericsson)
Katy Sherman (Orckit) Katy Sherman (Orckit)
Mike Sneed (Pulse) Mike Sneed (Pulse)
9. References 9. References
[1] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for [1] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for
Describing SNMP Management Frameworks", RFC 2571, April 1999. Describing SNMP Management Frameworks", RFC 2571, April 1999.
[2] Rose, M., and K. McCloghrie, "Structure and Identification of [2] Rose, M., and K. McCloghrie, "Structure and Identification of
skipping to change at line 2421 skipping to change at line 2650
Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.
[6] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, [6] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose,
M., and S. Waldbusser, "Textual Conventions for SMIv2", STD 58, M., and S. Waldbusser, "Textual Conventions for SMIv2", STD 58,
RFC 2579, April 1999. RFC 2579, April 1999.
[7] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, [7] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose,
M., and S. Waldbusser, "Conformance Statements for SMIv2", STD 58, M., and S. Waldbusser, "Conformance Statements for SMIv2", STD 58,
RFC 2580, April 1999. RFC 2580, April 1999.
Expires November 8, 2000 Page [48]
[8] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple [8] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple
Network Management Protocol", STD 15, RFC 1157, May 1990. Network Management Protocol", STD 15, RFC 1157, May 1990.
[9] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, [9] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Introduction to Community-based SNMPv2", RFC 1901, January "Introduction to Community-based SNMPv2", RFC 1901, January
1996. 1996.
[10] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Transport [10] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Transport
Mappings for Version 2 of the Simple Network Management Protocol Mappings for Version 2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1906, January 1996. (SNMPv2)", RFC 1906, January 1996.
[11] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message [11] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message
Processing and Dispatching for the Simple Network Management Processing and Dispatching for the Simple Network Management
Protocol (SNMP)", RFC 2572, April 1999. Protocol (SNMP)", RFC 2572, April 1999.
[12] Blumenthal, U., and B. Wijnen, "User-based Security Model (USM) [12] Blumenthal, U., and B. Wijnen, "User-based Security Model (USM)
for version 3 of the Simple Network Management Protocol (SNMPv3)", for version 3 of the Simple Network Management Protocol (SNMPv3)",
RFC 2574, April 1999. RFC 2574, April 1999.
Expires November 8, 2000 Page [43]
[13] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol [13] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol
Operations for Version 2 of the Simple Network Management Protocol Operations for Version 2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1905, January 1996. (SNMPv2)", RFC 1905, January 1996.
[14] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC [14] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC
2573, April 1999. 2573, April 1999.
[15] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based Access [15] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based Access
Control Model (VACM) for the Simple Network Management Protocol Control Model (VACM) for the Simple Network Management Protocol
(SNMP)", RFC 2575, April 1999. (SNMP)", RFC 2575, April 1999.
skipping to change at line 2477 skipping to change at line 2706
for Network Management of TCP/IP-based internets: MIB-II", STD 17, for Network Management of TCP/IP-based internets: MIB-II", STD 17,
RFC 1213, March 1991. RFC 1213, March 1991.
[21] McCloghrie, K., and Kastenholz, F., "The Interfaces Group MIB", [21] McCloghrie, K., and Kastenholz, F., "The Interfaces Group MIB",
RFC 2863, June 2000. RFC 2863, June 2000.
[22] Tesink, K., "Textual Conventions for MIB Modules Using Performance [22] Tesink, K., "Textual Conventions for MIB Modules Using Performance
History Based on 15 Minute Intervals", RFC 2493, January 1999. History Based on 15 Minute Intervals", RFC 2493, January 1999.
[23] Bathrick, G., Ly, F., "Definitions of Managed Objects for the ADSL [23] Bathrick, G., Ly, F., "Definitions of Managed Objects for the ADSL
Expires November 8, 2000 Page [49]
Lines", RFC 2662, August 1999. Lines", RFC 2662, August 1999.
10. Intellectual Property Notice 10. Intellectual Property Notice
The IETF takes no position regarding the validity or scope of any The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11. Copies of standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances of claims of rights made available for publication and any assurances of
licenses to be made available, or the result of an attempt made to licenses to be made available, or the result of an attempt made to
obtain a general license or permission for the use of such obtain a general license or permission for the use of such
proprietary rights by implementors or users of this specification can proprietary rights by implementors or users of this specification can
be obtained from the IETF Secretariat. be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary copyrights, patents or patent applications, or other proprietary
Expires November 8, 2000 Page [44]
rights which may cover technology that may be required to practice rights which may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive this standard. Please address the information to the IETF Executive
Director. Director.
11. Authors' Addresses 11. Authors' Addresses
Bob Ray Bob Ray
Verilink Corporation Verilink Corporation
127 Jetplex Circle 127 Jetplex Circle
Madison, AL 35758 USA Madison, AL 35758 USA
skipping to change at line 2534 skipping to change at line 2763
Copyright (C) The Internet Society (1999). All Rights Reserved. Copyright (C) The Internet Society (1999). All Rights Reserved.
This document and translations of it may be copied and furnished to This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other the copyright notice or references to the Internet Society or other
Expires November 8, 2000 Page [50]
Internet organizations, except as needed for the purpose of Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than followed, or as required to translate it into languages other than
English. English.
The limited permissions granted above are perpetual and will not be The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns. revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Expires November 8, 2000 Page [45] Expires November 8, 2000 Page [51]
 End of changes. 

This html diff was produced by rfcdiff 1.23, available from http://www.levkowetz.com/ietf/tools/rfcdiff/