draft-ietf-adslmib-hdsl2-04.txt   draft-ietf-adslmib-hdsl2-05.txt 
INTERNET-DRAFT B. Ray INTERNET-DRAFT B. Ray
Verilink Corporation Verilink Corporation
R. Abbi R. Abbi
Alcatel Alcatel
October 2000 October 2000
Definitions of Managed Objects for HDSL2 and SHDSL Lines Definitions of Managed Objects for HDSL2 and SHDSL Lines
draft-ietf-adslmib-hdsl2-04.txt draft-ietf-adslmib-hdsl2-05.txt
Status of this Memo Status of this Memo
This document is an Internet-Draft and is in full conformance with This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC 2026. all provisions of Section 10 of RFC 2026.
Internet-Drafts are working documents of the Internet Engineering Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that other Task Force (IETF), its areas, and its working groups. Note that other
groups may also distribute working documents as Internet-Drafts. groups may also distribute working documents as Internet-Drafts.
skipping to change at line 41 skipping to change at line 41
To view the entire list of current Internet-Drafts, please check the To view the entire list of current Internet-Drafts, please check the
"1id-abstracts.txt" listing contained in the Internet-Drafts Shadow "1id-abstracts.txt" listing contained in the Internet-Drafts Shadow
Directories on ftp.is.co.za (Africa), ftp.nordu.net (Northern Directories on ftp.is.co.za (Africa), ftp.nordu.net (Northern
Europe), ftp.nis.garr.it (Southern Europe), munnari.oz.au (Pacific Europe), ftp.nis.garr.it (Southern Europe), munnari.oz.au (Pacific
Rim), ftp.ietf.org (US East Coast), or ftp.isi.edu (US West Coast). Rim), ftp.ietf.org (US East Coast), or ftp.isi.edu (US West Coast).
Copyright Notice Copyright Notice
Copyright (C) The Internet Society (2000). All Rights Reserved. Copyright (C) The Internet Society (2000). All Rights Reserved.
Expires November 8, 2000 Page [1] Expires April 30, 2001 Page [1]
Table of Contents Table of Contents
1. Abstract .................................................. 2 1. Abstract .................................................. 2
2. The SNMPv2 Network Management Framework ................... 2 2. The SNMPv2 Network Management Framework ................... 2
3. Introduction .............................................. 3 3. Introduction .............................................. 3
3.1 Relationship of the MIB with Standard MIBs ................ 4 3.1 Relationship of the MIB with Standard MIBs ................ 4
4. Conventions used in the MIB ............................... 5 4. Conventions used in the MIB ............................... 5
4.1 Naming Conventions ........................................ 5 4.1 Naming Conventions ........................................ 5
4.2 Textual Conventions ....................................... 5 4.2 Textual Conventions ....................................... 5
skipping to change at line 96 skipping to change at line 96
STD 16, RFC 1155 [2], STD 16, RFC 1212 [3] and RFC 1215 [4]. STD 16, RFC 1155 [2], STD 16, RFC 1212 [3] and RFC 1215 [4].
The second version, called SMIv2, is described in STD 58, RFC The second version, called SMIv2, is described in STD 58, RFC
2578 [5], STD 58, RFC 2579 [6] and STD 58, RFC 2580 [7]. 2578 [5], STD 58, RFC 2579 [6] and STD 58, RFC 2580 [7].
o Message protocols for transferring management information. The o Message protocols for transferring management information. The
first version of the SNMP message protocol is called SNMPv1 and first version of the SNMP message protocol is called SNMPv1 and
described in STD 15, RFC 1157 [8]. A second version of the SNMP described in STD 15, RFC 1157 [8]. A second version of the SNMP
message protocol, which is not an Internet standards track message protocol, which is not an Internet standards track
protocol, is called SNMPv2c and described in RFC 1901 [9] and protocol, is called SNMPv2c and described in RFC 1901 [9] and
Expires November 8, 2000 Page [2] Expires April 30, 2001 Page [2]
RFC 1906 [10]. The third version of the message protocol is RFC 1906 [10]. The third version of the message protocol is
called SNMPv3 and described in RFC 1906 [10], RFC 2572 [11] and called SNMPv3 and described in RFC 1906 [10], RFC 2572 [11] and
RFC 2574 [12]. RFC 2574 [12].
o Protocol operations for accessing management information. The o Protocol operations for accessing management information. The
first set of protocol operations and associated PDU formats is first set of protocol operations and associated PDU formats is
described in STD 15, RFC 1157 [8]. A second set of protocol described in STD 15, RFC 1157 [8]. A second set of protocol
operations and associated PDU formats is described in RFC 1905 operations and associated PDU formats is described in RFC 1905
[13]. [13].
skipping to change at line 151 skipping to change at line 151
often use a textual string, termed the descriptor, to also refer to often use a textual string, termed the descriptor, to also refer to
the object type. the object type.
3. Introduction 3. Introduction
This document describes an SNMP MIB for managing HDSL2/SHDSL Lines. This document describes an SNMP MIB for managing HDSL2/SHDSL Lines.
The MIB is intended to be compatible with both the SNMPv1 and SNMPv2. The MIB is intended to be compatible with both the SNMPv1 and SNMPv2.
These definitions are based upon the specifications for the HDSL2 and These definitions are based upon the specifications for the HDSL2 and
SHDSL Embedded Operations Channel (EOC) as defined in ANSI SHDSL Embedded Operations Channel (EOC) as defined in ANSI
Expires November 8, 2000 Page [3] Expires April 30, 2001 Page [3]
T1E1.4/2000-006 [18] and ITU G.991.2 (ex G.SHDSL) [19]. T1E1.4/2000-006 [18] and ITU G.991.2 (ex G.SHDSL) [19].
The MIB will eventually be located in the MIB tree under MIB 2 The MIB will eventually be located in the MIB tree under MIB 2
transmission, as discussed in the MIB-2 Integration (RFC 1213 [20] and transmission, as discussed in the MIB-2 Integration (RFC 1213 [20] and
RFC 2863 [21]) section of this document. Until approved by the IETF, RFC 2863 [21]) section of this document. Until approved by the IETF,
vendors may also choose to support it under the experimental tree. vendors may also choose to support it under the experimental tree.
NOTE TO RFC EDITOR: please replace the above paragraph with the NOTE TO RFC EDITOR: please replace the above paragraph with the
following paragraph when appropriate: following paragraph when appropriate:
skipping to change at line 206 skipping to change at line 206
The MIB branch identified by this ifType contains tables appropriate The MIB branch identified by this ifType contains tables appropriate
for this interface type. Most such tables extend the ifEntry table, for this interface type. Most such tables extend the ifEntry table,
and are indexed by ifIndex. and are indexed by ifIndex.
The following attributes are part of the mandatory ifGeneral group in The following attributes are part of the mandatory ifGeneral group in
RFC 2863 [21], and are not duplicated in the HDSL2/SHDSL Line MIB. RFC 2863 [21], and are not duplicated in the HDSL2/SHDSL Line MIB.
=================================================================== ===================================================================
ifIndex Interface index. ifIndex Interface index.
Expires November 8, 2000 Page [4] Expires April 30, 2001 Page [4]
ifDescr See interfaces MIB [21]. ifDescr See interfaces MIB [21].
ifType hdsl2(168) or shdsl(169). ifType hdsl2(168) or shdsl(169).
ifSpeed Set as appropriate. ifSpeed Set as appropriate.
(This is fixed at 1552000 for HDSL2 lines) (This is fixed at 1552000 for HDSL2 lines)
ifPhysAddress This object should have an octet string ifPhysAddress This object should have an octet string
with zero length. with zero length.
skipping to change at line 261 skipping to change at line 261
K. LOSWS means LOSW second. K. LOSWS means LOSW second.
L. SES means severely errored second. L. SES means severely errored second.
M. SNR means signal-to-noise ratio. M. SNR means signal-to-noise ratio.
N. UAS means unavailable second. N. UAS means unavailable second.
4.2. Textual Conventions 4.2. Textual Conventions
The following textual conventions are defined to reflect the line The following textual conventions are defined to reflect the line
topology in the MIB (further discussed is the following section) topology in the MIB (further discussed is the following section)
Expires November 8, 2000 Page [5] Expires April 30, 2001 Page [5]
and to define the behaviour of the statistics to be maintained and to define the behaviour of the statistics to be maintained
by an agent. by an agent.
o Hdsl2ShdslUnitId : o Hdsl2ShdslUnitId :
This attribute uniquely identifies each unit in a HDSL2/SHDSL span. This attribute uniquely identifies each unit in a HDSL2/SHDSL span.
It mirrors the EOC addressing mechanism: It mirrors the EOC addressing mechanism:
xtuC(1) - CO terminal unit xtuC(1) - CO terminal unit
xtuR(2) - CPE terminal unit xtuR(2) - CPE terminal unit
skipping to change at line 317 skipping to change at line 317
This attribute defines the behaviour of the elapsed time counters This attribute defines the behaviour of the elapsed time counters
found in the MIB. found in the MIB.
o Hdsl2ShdslPerfIntervalThreshold: o Hdsl2ShdslPerfIntervalThreshold:
This attribute defines the behaviour of the alarm thresholds found This attribute defines the behaviour of the alarm thresholds found
in the MIB. in the MIB.
4.3. Structure 4.3. Structure
Expires November 8, 2000 Page [6] Expires April 30, 2001 Page [6]
The MIB is structured into following MIB groups: The MIB is structured into following MIB groups:
o Span Configuration Group: o Span Configuration Group:
This group supports MIB objects for configuring parameters for This group supports MIB objects for configuring parameters for
the HDSL2/SHDSL span. It contains the following table(s): the HDSL2/SHDSL span. It contains the following table(s):
- hdsl2ShdslSpanConfTable - hdsl2ShdslSpanConfTable
skipping to change at line 373 skipping to change at line 373
in 15-minute intervals. It contains the following table(s): in 15-minute intervals. It contains the following table(s):
- hdsl2Shdsl15MinIntervalTable - hdsl2Shdsl15MinIntervalTable
o Segment Endpoint 1-Day Interval Status/Performance Group: o Segment Endpoint 1-Day Interval Status/Performance Group:
This group supports MIB objects that provide historic This group supports MIB objects that provide historic
status/performance information relating to segment endpoints status/performance information relating to segment endpoints
in 1-day intervals. It contains the following table(s): in 1-day intervals. It contains the following table(s):
Expires November 8, 2000 Page [7] Expires April 30, 2001 Page [7]
- hdsl2Shdsl1DayIntervalTable - hdsl2Shdsl1DayIntervalTable
o Maintenance Group: o Maintenance Group:
This group supports MIB objects for performing maintenance This group supports MIB objects for performing maintenance
operations such as loopbacks for HDSL2/SHDSL lines. It contains operations such as loopbacks for HDSL2/SHDSL lines. It contains
the following table(s): the following table(s):
- hdsl2ShdslEndpointMaintTable - hdsl2ShdslEndpointMaintTable
- hdsl2ShdslUnitMaintTable - hdsl2ShdslUnitMaintTable
skipping to change at line 422 skipping to change at line 422
- hdsl2ShdslSpanInvalidNumRepeaters - hdsl2ShdslSpanInvalidNumRepeaters
- hdsl2ShdslLoopbackFailure - hdsl2ShdslLoopbackFailure
4.3.1 Line Topology 4.3.1 Line Topology
An HDSL2/SHDSL Line consists of a minimum of two units - xtuC (the An HDSL2/SHDSL Line consists of a minimum of two units - xtuC (the
central termination unit) and an xtuR (the remote termination unit). central termination unit) and an xtuR (the remote termination unit).
The line may optionally support up to 8 repeater/regenerator units The line may optionally support up to 8 repeater/regenerator units
(xru) as shown in the figure below. (xru) as shown in the figure below.
Expires November 8, 2000 Page [8] Expires April 30, 2001 Page [8]
<-- Network Side Customer Side --> <-- Network Side Customer Side -->
|</////////////////// HDSL2/SHDSL Span ////////////////////>| |</////////////////// HDSL2/SHDSL Span ////////////////////>|
<~~~> <~~~> HDSL2/SHDSL Segments <~~~> <~~~> <~~~> HDSL2/SHDSL Segments <~~~>
+-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+
+ C=1=N C=1=N C=..1..=N C=1=N + + C=1=N C=1=N C=..1..=N C=1=N +
| xtuC | | xru1 | | xru2 | | xru8 | | xtuR | | xtuC | | xru1 | | xru2 | | xru8 | | xtuR |
+ C=2=N C=2=N C=..2..=N C=2=N + + C=2=N C=2=N C=..2..=N C=2=N +
skipping to change at line 475 skipping to change at line 475
the scope of this MIB). the scope of this MIB).
4.5. Profiles 4.5. Profiles
As a managed node can handle a large number of xUs, (e.g., hundreds As a managed node can handle a large number of xUs, (e.g., hundreds
or perhaps thousands of lines), provisioning every parameter on every or perhaps thousands of lines), provisioning every parameter on every
xU may become burdensome. Moreover, most lines are provisioned xU may become burdensome. Moreover, most lines are provisioned
identically; with the same set of parameters. To simplify the identically; with the same set of parameters. To simplify the
provisioning process, this MIB makes use of profiles. A profile is a provisioning process, this MIB makes use of profiles. A profile is a
Expires November 8, 2000 Page [9] Expires April 30, 2001 Page [9]
set of parameters that can be shared by multiple lines using the same set of parameters that can be shared by multiple lines using the same
configuration. configuration.
The following profiles are used in this MIB: The following profiles are used in this MIB:
o Span Configuration Profiles - Span configuration profiles contain o Span Configuration Profiles - Span configuration profiles contain
parameters for configuring HDSL2/SHDSL spans. They are defined in parameters for configuring HDSL2/SHDSL spans. They are defined in
the hdsl2ShdslSpanConfProfileTable. Since span configuration the hdsl2ShdslSpanConfProfileTable. Since span configuration
parameters are only applicable for SHDSL, the support for span parameters are only applicable for SHDSL, the support for span
skipping to change at line 531 skipping to change at line 531
Changes to alarm profiles MUST take effect immediately. Changes to Changes to alarm profiles MUST take effect immediately. Changes to
non-alarm profiles MAY be deferred until the next restart (hard reset non-alarm profiles MAY be deferred until the next restart (hard reset
or soft restart) of the units on the line. Vendors MAY choose to have or soft restart) of the units on the line. Vendors MAY choose to have
the non-alarm profile changes take effect immediately. Alarm profiles the non-alarm profile changes take effect immediately. Alarm profiles
are those profile settings found in the are those profile settings found in the
hdsl2ShdslEndpointAlarmConfProfileTable. Non-alarm profiles are those hdsl2ShdslEndpointAlarmConfProfileTable. Non-alarm profiles are those
profile settings found in the hdsl2ShdslSpanConfTable and profile settings found in the hdsl2ShdslSpanConfTable and
hdsl2ShdslSpanConfProfileTable. hdsl2ShdslSpanConfProfileTable.
Expires November 8, 2000 Page [10] Expires April 30, 2001 Page [10]
4.6. Traps 4.6. Traps
The ability to generate the SNMP traps coldStart/WarmStart (per [21]) The ability to generate the SNMP traps coldStart/WarmStart (per [21])
which are per agent (e.g., per DSLAM in such a device), and linkUp / which are per agent (e.g., per DSLAM in such a device), and linkUp /
linkDown (per [21]) -- which are per interface (i.e., HDSL2/SHDSL line) linkDown (per [21]) -- which are per interface (i.e., HDSL2/SHDSL line)
is required. is required.
A linkDown trap may be generated whenever any of ES, SES, CRC Anomaly, A linkDown trap may be generated whenever any of ES, SES, CRC Anomaly,
LOSWS, or UAS event occurs. At this operational point, a manager can LOSWS, or UAS event occurs. At this operational point, a manager can
skipping to change at line 587 skipping to change at line 587
current 15-minute counter are reset to 0 every 15 minutes, if the current 15-minute counter are reset to 0 every 15 minutes, if the
condition persists, the trap may recur as often as every 15 minutes. condition persists, the trap may recur as often as every 15 minutes.
For example, to get a trap whenever a "loss of" event occurs (but at For example, to get a trap whenever a "loss of" event occurs (but at
most once every 15 minutes), set the corresponding threshold to 1. The most once every 15 minutes), set the corresponding threshold to 1. The
agent will generate a trap when the event originally occurs. agent will generate a trap when the event originally occurs.
Note that the NMS may receive a linkDown trap, as well, if enabled. At Note that the NMS may receive a linkDown trap, as well, if enabled. At
the beginning of the next 15 minute interval, the counter is reset. the beginning of the next 15 minute interval, the counter is reset.
When the first second goes by and the event occurs, the current When the first second goes by and the event occurs, the current
Expires November 8, 2000 Page [11] Expires April 30, 2001 Page [11]
interval bucket will be 1, which equals the threshold and the trap will interval bucket will be 1, which equals the threshold and the trap will
be sent again. be sent again.
5. Conformance and Compliance 5. Conformance and Compliance
For both HDSL2 and SHDSL lines, the following group(s) are mandatory: For both HDSL2 and SHDSL lines, the following group(s) are mandatory:
hdsl2ShdslSpanConfGroup hdsl2ShdslSpanConfGroup
hdsl2ShdslSpanStatusGroup hdsl2ShdslSpanStatusGroup
skipping to change at line 636 skipping to change at line 636
ifIndex FROM IF-MIB ifIndex FROM IF-MIB
PerfCurrentCount, PerfCurrentCount,
PerfIntervalCount FROM PerfHist-TC-MIB PerfIntervalCount FROM PerfHist-TC-MIB
SnmpAdminString FROM SNMP-FRAMEWORK-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB
MODULE-COMPLIANCE, MODULE-COMPLIANCE,
OBJECT-GROUP, OBJECT-GROUP,
NOTIFICATION-GROUP FROM SNMPv2-CONF; NOTIFICATION-GROUP FROM SNMPv2-CONF;
hdsl2ShdslMIB MODULE-IDENTITY hdsl2ShdslMIB MODULE-IDENTITY
LAST-UPDATED "000010160000Z" -- October 2, 2000 LAST-UPDATED "000010260000Z" -- October 26, 2000
ORGANIZATION "ADSLMIB Working Group" ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO CONTACT-INFO
Expires November 8, 2000 Page [12] Expires April 30, 2001 Page [12]
" "
Bob Ray Bob Ray
Verilink Corporation Verilink Corporation
127 Jetplex Circle 127 Jetplex Circle
Madison, AL 35758 USA Madison, AL 35758 USA
Tel: +1 256-774-2380 Tel: +1 256-774-2380
Fax: +1 256-774-2277 Fax: +1 256-774-2277
E-mail: bray@verilink.com E-mail: bray@verilink.com
skipping to change at line 698 skipping to change at line 698
The value of this counter starts at zero at the The value of this counter starts at zero at the
beginning of an interval and is increased when beginning of an interval and is increased when
associated events occur, until the end of the associated events occur, until the end of the
1-day interval. At that time the value of the 1-day interval. At that time the value of the
counter is stored in the previous 1-day history counter is stored in the previous 1-day history
interval, if available, and the current interval interval, if available, and the current interval
counter is restarted at zero. counter is restarted at zero.
In the case where the agent has no valid data available In the case where the agent has no valid data available
Expires November 8, 2000 Page [13] Expires April 30, 2001 Page [13]
for this interval the corresponding object for this interval the corresponding object
instance is not available and upon a retrieval instance is not available and upon a retrieval
request a corresponding error message shall be request a corresponding error message shall be
returned to indicate that this instance does returned to indicate that this instance does
not exist (for example, a noSuchName error for not exist (for example, a noSuchName error for
SNMPv1 and a noSuchInstance for SNMPv2 GET SNMPv1 and a noSuchInstance for SNMPv2 GET
operation)." operation)."
SYNTAX Gauge32 SYNTAX Gauge32
Hdsl2Shdsl1DayIntervalCount ::= TEXTUAL-CONVENTION Hdsl2Shdsl1DayIntervalCount ::= TEXTUAL-CONVENTION
skipping to change at line 753 skipping to change at line 753
of this type may have a range of 0...900, where of this type may have a range of 0...900, where
the value of 0 disables the alarm." the value of 0 disables the alarm."
SYNTAX INTEGER(0..900) SYNTAX INTEGER(0..900)
Hdsl2ShdslUnitId ::= TEXTUAL-CONVENTION Hdsl2ShdslUnitId ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This is the unique identification for all units "This is the unique identification for all units
in an HDSL2/SHDSL Span. It is based on the EOC in an HDSL2/SHDSL Span. It is based on the EOC
Expires November 8, 2000 Page [14] Expires April 30, 2001 Page [14]
unit addressing scheme with reference to the xtuC." unit addressing scheme with reference to the xtuC."
SYNTAX INTEGER SYNTAX INTEGER
{ {
xtuC(1), xtuC(1),
xtuR(2), xtuR(2),
xru1(3), xru1(3),
xru2(4), xru2(4),
xru3(5), xru3(5),
xru4(6), xru4(6),
xru5(7), xru5(7),
skipping to change at line 808 skipping to change at line 808
represented as a bit-map of possible settings. The various represented as a bit-map of possible settings. The various
bit positions are: bit positions are:
1 region 1 Indicates ITU-T G.991.2 Annex A. 1 region 1 Indicates ITU-T G.991.2 Annex A.
2 region 2 Indicates ITU-T G.991.2 Annex B. 2 region 2 Indicates ITU-T G.991.2 Annex B.
4 region 3 Indicates ITU-T G.991.2 Annex C." 4 region 3 Indicates ITU-T G.991.2 Annex C."
SYNTAX Integer32 SYNTAX Integer32
Expires November 8, 2000 Page [15] Expires April 30, 2001 Page [15]
-- Span Configuration Group -- Span Configuration Group
-- --
hdsl2ShdslSpanConfTable OBJECT-TYPE hdsl2ShdslSpanConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfEntry SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table supports overall configuration of "This table supports overall configuration of
skipping to change at line 864 skipping to change at line 864
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is a pointer to a span configuration profile in "This object is a pointer to a span configuration profile in
the hdsl2ShdslSpanConfProfileTable, which applies to this span. the hdsl2ShdslSpanConfProfileTable, which applies to this span.
The value of this object is the index of the referenced profile The value of this object is the index of the referenced profile
in the hdsl2ShdslSpanConfProfileTable. Note that span in the hdsl2ShdslSpanConfProfileTable. Note that span
configuration profiles are only applicable to SHDSL lines. configuration profiles are only applicable to SHDSL lines.
HDSL2 lines will not support this object. By default, this HDSL2 lines will not support this object. By default, this
object will have the value 'DEFVAL' (the index of the default object will have the value 'DEFVAL' (the index of the default
Expires November 8, 2000 Page [16] Expires April 30, 2001 Page [16]
profile)." profile)."
::= { hdsl2ShdslSpanConfEntry 2 } ::= { hdsl2ShdslSpanConfEntry 2 }
hdsl2ShdslSpanAlarmConfProfile OBJECT-TYPE hdsl2ShdslSpanAlarmConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32)) SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is a pointer to an Alarm configuration profile in "This object is a pointer to an Alarm configuration profile in
the hdsl2ShdslEndpointAlarmConfProfileTable. The value of this the hdsl2ShdslEndpointAlarmConfProfileTable. The value of this
skipping to change at line 919 skipping to change at line 919
Hdsl2ShdslSpanStatusEntry ::= Hdsl2ShdslSpanStatusEntry ::=
SEQUENCE SEQUENCE
{ {
hdsl2ShdslStatusNumAvailRepeaters INTEGER, hdsl2ShdslStatusNumAvailRepeaters INTEGER,
hdsl2ShdslStatusMaxAttainableLineRate Integer32, hdsl2ShdslStatusMaxAttainableLineRate Integer32,
hdsl2ShdslStatusActualLineRate Integer32, hdsl2ShdslStatusActualLineRate Integer32,
hdsl2ShdslStatusTransmissionModeCurrent hdsl2ShdslStatusTransmissionModeCurrent
Hdsl2ShdslTransmissionModeType Hdsl2ShdslTransmissionModeType
} }
Expires November 8, 2000 Page [17] Expires April 30, 2001 Page [17]
hdsl2ShdslStatusNumAvailRepeaters OBJECT-TYPE hdsl2ShdslStatusNumAvailRepeaters OBJECT-TYPE
SYNTAX INTEGER(0..8) SYNTAX INTEGER(0..8)
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Contains the actual number of repeaters/regenerators "Contains the actual number of repeaters/regenerators
discovered in this HDSL2/SHDSL span." discovered in this HDSL2/SHDSL span."
::= { hdsl2ShdslSpanStatusEntry 1 } ::= { hdsl2ShdslSpanStatusEntry 1 }
skipping to change at line 975 skipping to change at line 975
available via the EOC from units in a HDSL2/SHDSL line." available via the EOC from units in a HDSL2/SHDSL line."
::= { hdsl2ShdslMibObjects 3 } ::= { hdsl2ShdslMibObjects 3 }
hdsl2ShdslInventoryEntry OBJECT-TYPE hdsl2ShdslInventoryEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslInventoryEntry SYNTAX Hdsl2ShdslInventoryEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2ShdslInventoryTable. Each entry "An entry in the hdsl2ShdslInventoryTable. Each entry
Expires November 8, 2000 Page [18] Expires April 30, 2001 Page [18]
represents inventory information for a single unit in a represents inventory information for a single unit in a
HDSL2/SHDSL line. It is indexed by the ifIndex of the HDSL2/SHDSL line. It is indexed by the ifIndex of the
HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the
associated unit." associated unit."
INDEX { ifIndex, hdsl2ShdslInvIndex } INDEX { ifIndex, hdsl2ShdslInvIndex }
::= { hdsl2ShdslInventoryTable 1 } ::= { hdsl2ShdslInventoryTable 1 }
Hdsl2ShdslInventoryEntry ::= Hdsl2ShdslInventoryEntry ::=
SEQUENCE SEQUENCE
{ {
skipping to change at line 1030 skipping to change at line 1030
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Vendor model number as reported in an Inventory Response "Vendor model number as reported in an Inventory Response
message." message."
::= { hdsl2ShdslInventoryEntry 3 } ::= { hdsl2ShdslInventoryEntry 3 }
hdsl2ShdslInvVendorSerialNumber OBJECT-TYPE hdsl2ShdslInvVendorSerialNumber OBJECT-TYPE
SYNTAX DisplayString SYNTAX DisplayString
MAX-ACCESS read-only MAX-ACCESS read-only
Expires November 8, 2000 Page [19] Expires April 30, 2001 Page [19]
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Vendor serial number as reported in an Inventory Response "Vendor serial number as reported in an Inventory Response
message." message."
::= { hdsl2ShdslInventoryEntry 4 } ::= { hdsl2ShdslInventoryEntry 4 }
hdsl2ShdslInvVendorEOCSoftwareVersion OBJECT-TYPE hdsl2ShdslInvVendorEOCSoftwareVersion OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
skipping to change at line 1085 skipping to change at line 1085
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Vendor software version as reported in an Inventory "Vendor software version as reported in an Inventory
Response message." Response message."
::= { hdsl2ShdslInventoryEntry 9 } ::= { hdsl2ShdslInventoryEntry 9 }
hdsl2ShdslInvEquipmentCode OBJECT-TYPE hdsl2ShdslInvEquipmentCode OBJECT-TYPE
SYNTAX DisplayString SYNTAX DisplayString
Expires November 8, 2000 Page [20] Expires April 30, 2001 Page [20]
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Equipment code conforming to ANSI T1.213, Coded Identification "Equipment code conforming to ANSI T1.213, Coded Identification
of Equipment Entities." of Equipment Entities."
::= { hdsl2ShdslInventoryEntry 10 } ::= { hdsl2ShdslInventoryEntry 10 }
hdsl2ShdslInvVendorOther OBJECT-TYPE hdsl2ShdslInvVendorOther OBJECT-TYPE
SYNTAX DisplayString SYNTAX DisplayString
MAX-ACCESS read-only MAX-ACCESS read-only
skipping to change at line 1140 skipping to change at line 1140
UnitId of the associated unit, the side of the unit, and the UnitId of the associated unit, the side of the unit, and the
wire-pair of the associated modem." wire-pair of the associated modem."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair} hdsl2ShdslEndpointWirePair}
::= { hdsl2ShdslEndpointConfTable 1 } ::= { hdsl2ShdslEndpointConfTable 1 }
Hdsl2ShdslEndpointConfEntry ::= Hdsl2ShdslEndpointConfEntry ::=
SEQUENCE SEQUENCE
{ {
Expires November 8, 2000 Page [21] Expires April 30, 2001 Page [21]
hdsl2ShdslEndpointSide Hdsl2ShdslUnitSide, hdsl2ShdslEndpointSide Hdsl2ShdslUnitSide,
hdsl2ShdslEndpointWirePair Hdsl2ShdslWirePair, hdsl2ShdslEndpointWirePair Hdsl2ShdslWirePair,
hdsl2ShdslEndpointAlarmConfProfile SnmpAdminString hdsl2ShdslEndpointAlarmConfProfile SnmpAdminString
} }
hdsl2ShdslEndpointSide OBJECT-TYPE hdsl2ShdslEndpointSide OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitSide SYNTAX Hdsl2ShdslUnitSide
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
skipping to change at line 1194 skipping to change at line 1194
hdsl2ShdslEndpointCurrTable OBJECT-TYPE hdsl2ShdslEndpointCurrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointCurrEntry SYNTAX SEQUENCE OF Hdsl2ShdslEndpointCurrEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table contains current status and performance information "This table contains current status and performance information
for segment endpoints in HDSL2/SHDSL Lines." for segment endpoints in HDSL2/SHDSL Lines."
::= { hdsl2ShdslMibObjects 5 } ::= { hdsl2ShdslMibObjects 5 }
Expires November 8, 2000 Page [22] Expires April 30, 2001 Page [22]
hdsl2ShdslEndpointCurrEntry OBJECT-TYPE hdsl2ShdslEndpointCurrEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointCurrEntry SYNTAX Hdsl2ShdslEndpointCurrEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2ShdslEndpointCurrTable. Each entry "An entry in the hdsl2ShdslEndpointCurrTable. Each entry
contains status and performance information relating to a contains status and performance information relating to a
single segment endpoint. It is indexed by the ifIndex of single segment endpoint. It is indexed by the ifIndex of
the HDSL2/SHDSL line, the UnitId of the associated unit, the HDSL2/SHDSL line, the UnitId of the associated unit,
skipping to change at line 1250 skipping to change at line 1250
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The current loop attenuation for this endpoint as "The current loop attenuation for this endpoint as
reported in a Network or Customer Side Performance reported in a Network or Customer Side Performance
Status message." Status message."
::= { hdsl2ShdslEndpointCurrEntry 1 } ::= { hdsl2ShdslEndpointCurrEntry 1 }
hdsl2ShdslEndpointCurrSnrMgn OBJECT-TYPE hdsl2ShdslEndpointCurrSnrMgn OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
Expires November 8, 2000 Page [23] Expires April 30, 2001 Page [23]
UNITS "dB" UNITS "dB"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The current SNR margin for this endpoint as reported "The current SNR margin for this endpoint as reported
in a Status Response/SNR message." in a Status Response/SNR message."
::= { hdsl2ShdslEndpointCurrEntry 2 } ::= { hdsl2ShdslEndpointCurrEntry 2 }
hdsl2ShdslEndpointCurrStatus OBJECT-TYPE hdsl2ShdslEndpointCurrStatus OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
skipping to change at line 1304 skipping to change at line 1304
due to incompatible protocol used by due to incompatible protocol used by
the paired endpoint. the paired endpoint.
512 noNeighborPresent Endpoint failure during initialization 512 noNeighborPresent Endpoint failure during initialization
due to no activation sequence detected due to no activation sequence detected
from paired endpoint. from paired endpoint.
1024 loopbackActive A loopback is currently active at this 1024 loopbackActive A loopback is currently active at this
Segment Endpoint. Segment Endpoint.
Expires November 8, 2000 Page [24] Expires April 30, 2001 Page [24]
This is intended to supplement ifOperStatus." This is intended to supplement ifOperStatus."
::= { hdsl2ShdslEndpointCurrEntry 3 } ::= { hdsl2ShdslEndpointCurrEntry 3 }
hdsl2ShdslEndpointES OBJECT-TYPE hdsl2ShdslEndpointES OBJECT-TYPE
SYNTAX Counter32 SYNTAX Counter32
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Errored Seconds (ES) on this endpoint since the xU "Count of Errored Seconds (ES) on this endpoint since the xU
skipping to change at line 1359 skipping to change at line 1359
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Unavailable Seconds (UAS) on this endpoint since "Count of Unavailable Seconds (UAS) on this endpoint since
the xU was last restarted." the xU was last restarted."
::= { hdsl2ShdslEndpointCurrEntry 8 } ::= { hdsl2ShdslEndpointCurrEntry 8 }
hdsl2ShdslEndpointCurr15MinTimeElapsed OBJECT-TYPE hdsl2ShdslEndpointCurr15MinTimeElapsed OBJECT-TYPE
Expires November 8, 2000 Page [25] Expires April 30, 2001 Page [25]
SYNTAX Hdsl2ShdslPerfTimeElapsed SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Total elapsed seconds in the current 15-minute interval." "Total elapsed seconds in the current 15-minute interval."
::= { hdsl2ShdslEndpointCurrEntry 9 } ::= { hdsl2ShdslEndpointCurrEntry 9 }
hdsl2ShdslEndpointCurr15MinES OBJECT-TYPE hdsl2ShdslEndpointCurr15MinES OBJECT-TYPE
SYNTAX PerfCurrentCount SYNTAX PerfCurrentCount
skipping to change at line 1414 skipping to change at line 1414
::= { hdsl2ShdslEndpointCurrEntry 13 } ::= { hdsl2ShdslEndpointCurrEntry 13 }
hdsl2ShdslEndpointCurr15MinUAS OBJECT-TYPE hdsl2ShdslEndpointCurr15MinUAS OBJECT-TYPE
SYNTAX PerfCurrentCount SYNTAX PerfCurrentCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Unavailable Seconds (UAS) in the current 15-minute "Count of Unavailable Seconds (UAS) in the current 15-minute
Expires November 8, 2000 Page [26] Expires April 30, 2001 Page [26]
interval." interval."
::= { hdsl2ShdslEndpointCurrEntry 14 } ::= { hdsl2ShdslEndpointCurrEntry 14 }
hdsl2ShdslEndpointCurr1DayTimeElapsed OBJECT-TYPE hdsl2ShdslEndpointCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Number of seconds that have elapsed since the beginning of "Number of seconds that have elapsed since the beginning of
the current 1-day interval." the current 1-day interval."
::= { hdsl2ShdslEndpointCurrEntry 15 } ::= { hdsl2ShdslEndpointCurrEntry 15 }
hdsl2ShdslEndpointCurr1DayES OBJECT-TYPE hdsl2ShdslEndpointCurr1DayES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Errored Seconds (ES) during the current day as "Count of Errored Seconds (ES) during the current day as
measured by hdslPerfCurr1DayTimeElapsed." measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
::= { hdsl2ShdslEndpointCurrEntry 16 } ::= { hdsl2ShdslEndpointCurrEntry 16 }
hdsl2ShdslEndpointCurr1DaySES OBJECT-TYPE hdsl2ShdslEndpointCurr1DaySES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Severely Errored Seconds (SES) during the current "Count of Severely Errored Seconds (SES) during the current
day as measured by hdslPerfCurr1DayTimeElapsed." day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
::= { hdsl2ShdslEndpointCurrEntry 17 } ::= { hdsl2ShdslEndpointCurrEntry 17 }
hdsl2ShdslEndpointCurr1DayCRCanomalies OBJECT-TYPE hdsl2ShdslEndpointCurr1DayCRCanomalies OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount SYNTAX Hdsl2ShdslPerfCurrDayCount
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of CRC anomalies during the current day as measured "Count of CRC anomalies during the current day as measured
by hdslPerfCurr1DayTimeElapsed." by hdsl2ShdslEndpointCurr1DayTimeElapsed."
::= { hdsl2ShdslEndpointCurrEntry 18 } ::= { hdsl2ShdslEndpointCurrEntry 18 }
hdsl2ShdslEndpointCurr1DayLOSWS OBJECT-TYPE hdsl2ShdslEndpointCurr1DayLOSWS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Loss of Sync Word Seconds (LOSWS) during the "Count of Loss of Sync Word Seconds (LOSWS) during the current
current day as measured by hdslPerfCurr1DayTimeElapsed." day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
::= { hdsl2ShdslEndpointCurrEntry 19 } ::= { hdsl2ShdslEndpointCurrEntry 19 }
hdsl2ShdslEndpointCurr1DayUAS OBJECT-TYPE hdsl2ShdslEndpointCurr1DayUAS OBJECT-TYPE
Expires November 8, 2000 Page [27] Expires April 30, 2001 Page [27]
SYNTAX Hdsl2ShdslPerfCurrDayCount SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Unavailable Seconds (UAS) during the current "Count of Unavailable Seconds (UAS) during the current
day as measured by hdslPerfCurr1DayTimeElapsed." day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
::= { hdsl2ShdslEndpointCurrEntry 20 } ::= { hdsl2ShdslEndpointCurrEntry 20 }
-- Segment Endpoint 15-Minute Interval Status/Performance Group -- Segment Endpoint 15-Minute Interval Status/Performance Group
-- --
hdsl2Shdsl15MinIntervalTable OBJECT-TYPE hdsl2Shdsl15MinIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2Shdsl15MinIntervalEntry SYNTAX SEQUENCE OF Hdsl2Shdsl15MinIntervalEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
skipping to change at line 1524 skipping to change at line 1524
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Performance Data Interval number. 1 is the the most recent "Performance Data Interval number. 1 is the the most recent
previous interval; interval 96 is 24 hours ago. Intervals previous interval; interval 96 is 24 hours ago. Intervals
2..96 are optional." 2..96 are optional."
::= { hdsl2Shdsl15MinIntervalEntry 1 } ::= { hdsl2Shdsl15MinIntervalEntry 1 }
hdsl2Shdsl15MinIntervalES OBJECT-TYPE hdsl2Shdsl15MinIntervalES OBJECT-TYPE
Expires November 8, 2000 Page [28] Expires April 30, 2001 Page [28]
SYNTAX PerfIntervalCount SYNTAX PerfIntervalCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Errored Seconds (ES) during the interval." "Count of Errored Seconds (ES) during the interval."
::= { hdsl2Shdsl15MinIntervalEntry 2 } ::= { hdsl2Shdsl15MinIntervalEntry 2 }
hdsl2Shdsl15MinIntervalSES OBJECT-TYPE hdsl2Shdsl15MinIntervalSES OBJECT-TYPE
SYNTAX PerfIntervalCount SYNTAX PerfIntervalCount
skipping to change at line 1579 skipping to change at line 1579
-- Segment Endpoint 1-Day Interval Status/Performance Group -- Segment Endpoint 1-Day Interval Status/Performance Group
-- --
hdsl2Shdsl1DayIntervalTable OBJECT-TYPE hdsl2Shdsl1DayIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2Shdsl1DayIntervalEntry SYNTAX SEQUENCE OF Hdsl2Shdsl1DayIntervalEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table provides one row for each HDSL2/SHDSL endpoint "This table provides one row for each HDSL2/SHDSL endpoint
Expires November 8, 2000 Page [29] Expires April 30, 2001 Page [29]
performance data collection interval." performance data collection interval."
::= { hdsl2ShdslMibObjects 7 } ::= { hdsl2ShdslMibObjects 7 }
hdsl2Shdsl1DayIntervalEntry OBJECT-TYPE hdsl2Shdsl1DayIntervalEntry OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalEntry SYNTAX Hdsl2Shdsl1DayIntervalEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2Shdsl1DayIntervalTable." "An entry in the hdsl2Shdsl1DayIntervalTable."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
skipping to change at line 1634 skipping to change at line 1634
be collected for any reason." be collected for any reason."
::= { hdsl2Shdsl1DayIntervalEntry 2 } ::= { hdsl2Shdsl1DayIntervalEntry 2 }
hdsl2Shdsl1DayIntervalES OBJECT-TYPE hdsl2Shdsl1DayIntervalES OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
Expires November 8, 2000 Page [30] Expires April 30, 2001 Page [30]
"Count of Errored Seconds (ES) during the 1-day interval as "Count of Errored Seconds (ES) during the 1-day interval as
measured by hdsl2Shdsl1DayIntervalMoniSecs." measured by hdsl2Shdsl1DayIntervalMoniSecs."
::= { hdsl2Shdsl1DayIntervalEntry 3 } ::= { hdsl2Shdsl1DayIntervalEntry 3 }
hdsl2Shdsl1DayIntervalSES OBJECT-TYPE hdsl2Shdsl1DayIntervalSES OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
skipping to change at line 1689 skipping to change at line 1689
hdsl2ShdslEndpointMaintTable OBJECT-TYPE hdsl2ShdslEndpointMaintTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointMaintEntry SYNTAX SEQUENCE OF Hdsl2ShdslEndpointMaintEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table supports maintenance operations (eg. loopbacks) "This table supports maintenance operations (eg. loopbacks)
to be performed on HDSL2/SHDSL segment endpoints." to be performed on HDSL2/SHDSL segment endpoints."
::= { hdsl2ShdslMibObjects 8 } ::= { hdsl2ShdslMibObjects 8 }
Expires November 8, 2000 Page [31] Expires April 30, 2001 Page [31]
hdsl2ShdslEndpointMaintEntry OBJECT-TYPE hdsl2ShdslEndpointMaintEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointMaintEntry SYNTAX Hdsl2ShdslEndpointMaintEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2ShdslEndpointMaintTable. Each entry "An entry in the hdsl2ShdslEndpointMaintTable. Each entry
corresponds to a single segment endpoint, and is indexed by the corresponds to a single segment endpoint, and is indexed by the
ifIndex of the HDSL2/SHDSL line, the UnitId of the associated ifIndex of the HDSL2/SHDSL line, the UnitId of the associated
unit and the side of the unit." unit and the side of the unit."
skipping to change at line 1745 skipping to change at line 1745
DESCRIPTION DESCRIPTION
"This object indicates the state of the tip/ring pair at "This object indicates the state of the tip/ring pair at
the associated segment endpoint." the associated segment endpoint."
::= { hdsl2ShdslEndpointMaintEntry 2 } ::= { hdsl2ShdslEndpointMaintEntry 2 }
hdsl2ShdslMaintPowerBackOff OBJECT-TYPE hdsl2ShdslMaintPowerBackOff OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
default(1), default(1),
Expires November 8, 2000 Page [32] Expires April 30, 2001 Page [32]
enhanced(2) enhanced(2)
} }
MAX-ACCESS read-write MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the receiver at the associated "This object configures the receiver at the associated
segment endpoint to operate in default or enhanced power segment endpoint to operate in default or enhanced power
backoff mode." backoff mode."
::= { hdsl2ShdslEndpointMaintEntry 3 } ::= { hdsl2ShdslEndpointMaintEntry 3 }
skipping to change at line 1800 skipping to change at line 1800
INDEX { ifIndex, hdsl2ShdslInvIndex } INDEX { ifIndex, hdsl2ShdslInvIndex }
::= { hdsl2ShdslUnitMaintTable 1 } ::= { hdsl2ShdslUnitMaintTable 1 }
Hdsl2ShdslUnitMaintEntry ::= Hdsl2ShdslUnitMaintEntry ::=
SEQUENCE SEQUENCE
{ {
hdsl2ShdslMaintLoopbackTimeout Integer32, hdsl2ShdslMaintLoopbackTimeout Integer32,
hdsl2ShdslMaintUnitPowerSource INTEGER hdsl2ShdslMaintUnitPowerSource INTEGER
} }
Expires November 8, 2000 Page [33] Expires April 30, 2001 Page [33]
hdsl2ShdslMaintLoopbackTimeout OBJECT-TYPE hdsl2ShdslMaintLoopbackTimeout OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
MAX-ACCESS read-write MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the timeout value for loopbacks "This object configures the timeout value for loopbacks
initiated at segments endpoints contained in the associated initiated at segments endpoints contained in the associated
unit. A value of 0 disables the timeout." unit. A value of 0 disables the timeout."
::= { hdsl2ShdslUnitMaintEntry 1 } ::= { hdsl2ShdslUnitMaintEntry 1 }
skipping to change at line 1856 skipping to change at line 1856
applied to those lines referencing that profile (see the applied to those lines referencing that profile (see the
hdsl2ShdslSpanConfProfile object). Profiles may be hdsl2ShdslSpanConfProfile object). Profiles may be
created/deleted using the row creation/deletion mechanism created/deleted using the row creation/deletion mechanism
via hdsl2ShdslSpanConfProfileRowStatus. Profiles that are via hdsl2ShdslSpanConfProfileRowStatus. Profiles that are
being referenced may not be deleted." being referenced may not be deleted."
INDEX { IMPLIED hdsl2ShdslSpanConfProfileName } INDEX { IMPLIED hdsl2ShdslSpanConfProfileName }
::= { hdsl2ShdslSpanConfProfileTable 1 } ::= { hdsl2ShdslSpanConfProfileTable 1 }
Hdsl2ShdslSpanConfProfileEntry ::= Hdsl2ShdslSpanConfProfileEntry ::=
Expires November 8, 2000 Page [34] Expires April 30, 2001 Page [34]
SEQUENCE SEQUENCE
{ {
hdsl2ShdslSpanConfProfileName SnmpAdminString, hdsl2ShdslSpanConfProfileName SnmpAdminString,
hdsl2ShdslSpanWireInterface INTEGER, hdsl2ShdslSpanWireInterface INTEGER,
hdsl2ShdslSpanMinLineRate Integer32, hdsl2ShdslSpanMinLineRate Integer32,
hdsl2ShdslSpanMaxLineRate Integer32, hdsl2ShdslSpanMaxLineRate Integer32,
hdsl2ShdslSpanConfPSD INTEGER, hdsl2ShdslSpanConfPSD INTEGER,
hdsl2ShdslSpanConfTransmissionMode Hdsl2ShdslTransmissionModeType, hdsl2ShdslSpanConfTransmissionMode Hdsl2ShdslTransmissionModeType,
hdsl2ShdslSpanRemoteEnabled INTEGER, hdsl2ShdslSpanRemoteEnabled INTEGER,
hdsl2ShdslSpanPowerFeeding INTEGER, hdsl2ShdslSpanPowerFeeding INTEGER,
skipping to change at line 1911 skipping to change at line 1911
'fixed'. If the minimum line rate is less than the maximum 'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'." line rate, the line rate is considered 'rate-adaptive'."
::= { hdsl2ShdslSpanConfProfileEntry 3 } ::= { hdsl2ShdslSpanConfProfileEntry 3 }
hdsl2ShdslSpanMaxLineRate OBJECT-TYPE hdsl2ShdslSpanMaxLineRate OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
UNITS "bps" UNITS "bps"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
Expires November 8, 2000 Page [35] Expires April 30, 2001 Page [35]
DESCRIPTION DESCRIPTION
"This object configures the maximum transmission rate for "This object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered (hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum 'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'." line rate, the line rate is considered 'rate-adaptive'."
::= { hdsl2ShdslSpanConfProfileEntry 4 } ::= { hdsl2ShdslSpanConfProfileEntry 4 }
hdsl2ShdslSpanConfPSD OBJECT-TYPE hdsl2ShdslSpanConfPSD OBJECT-TYPE
skipping to change at line 1966 skipping to change at line 1966
::= { hdsl2ShdslSpanConfProfileEntry 7 } ::= { hdsl2ShdslSpanConfProfileEntry 7 }
hdsl2ShdslSpanPowerFeeding OBJECT-TYPE hdsl2ShdslSpanPowerFeeding OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
noPower(1), noPower(1),
powerFeed(2), powerFeed(2),
wettingCurrent(3) wettingCurrent(3)
} }
Expires November 8, 2000 Page [36] Expires April 30, 2001 Page [36]
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object enables/disables support for optional power "This object enables/disables support for optional power
feeding in a SHDSL line." feeding in a SHDSL line."
::= { hdsl2ShdslSpanConfProfileEntry 8 } ::= { hdsl2ShdslSpanConfProfileEntry 8 }
hdsl2ShdslSpanConfProfileRowStatus OBJECT-TYPE hdsl2ShdslSpanConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus SYNTAX RowStatus
MAX-ACCESS read-create MAX-ACCESS read-create
skipping to change at line 2021 skipping to change at line 2021
SEQUENCE SEQUENCE
{ {
hdsl2ShdslEndpointAlarmConfProfileName SnmpAdminString, hdsl2ShdslEndpointAlarmConfProfileName SnmpAdminString,
hdsl2ShdslEndpointThreshLoopAttenuation Integer32, hdsl2ShdslEndpointThreshLoopAttenuation Integer32,
hdsl2ShdslEndpointThreshSNRMargin Integer32, hdsl2ShdslEndpointThreshSNRMargin Integer32,
hdsl2ShdslEndpointThreshES hdsl2ShdslEndpointThreshES
Hdsl2ShdslPerfIntervalThreshold, Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshSES hdsl2ShdslEndpointThreshSES
Hdsl2ShdslPerfIntervalThreshold, Hdsl2ShdslPerfIntervalThreshold,
Expires November 8, 2000 Page [37] Expires April 30, 2001 Page [37]
hdsl2ShdslEndpointThreshCRCanomalies Integer32, hdsl2ShdslEndpointThreshCRCanomalies Integer32,
hdsl2ShdslEndpointThreshLOSWS hdsl2ShdslEndpointThreshLOSWS
Hdsl2ShdslPerfIntervalThreshold, Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshUAS hdsl2ShdslEndpointThreshUAS
Hdsl2ShdslPerfIntervalThreshold, Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointAlarmConfProfileRowStatus RowStatus hdsl2ShdslEndpointAlarmConfProfileRowStatus RowStatus
} }
hdsl2ShdslEndpointAlarmConfProfileName OBJECT-TYPE hdsl2ShdslEndpointAlarmConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32)) SYNTAX SnmpAdminString (SIZE(1..32))
skipping to change at line 2075 skipping to change at line 2075
DESCRIPTION DESCRIPTION
"This object configures the threshold for the number of "This object configures the threshold for the number of
errored seconds (ES) within any given 15-minute performance errored seconds (ES) within any given 15-minute performance
data collection interval. If the value of errored seconds data collection interval. If the value of errored seconds
in a particular 15-minute collection interval reaches/ in a particular 15-minute collection interval reaches/
exceeds this value, a hdsl2ShdslPerfESThreshTrap will be exceeds this value, a hdsl2ShdslPerfESThreshTrap will be
generated. One trap will be sent per interval per generated. One trap will be sent per interval per
endpoint." endpoint."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 4 } ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 4 }
Expires November 8, 2000 Page [38] Expires April 30, 2001 Page [38]
hdsl2ShdslEndpointThreshSES OBJECT-TYPE hdsl2ShdslEndpointThreshSES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the threshold for the number of "This object configures the threshold for the number of
severely errored seconds (SES) within any given 15-minute severely errored seconds (SES) within any given 15-minute
performance data collection interval. If the value of severely performance data collection interval. If the value of severely
skipping to change at line 2131 skipping to change at line 2131
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the threshold for the number of "This object configures the threshold for the number of
unavailable seconds (UAS) within any given 15-minute unavailable seconds (UAS) within any given 15-minute
performance data collection interval. If the value of UAS performance data collection interval. If the value of UAS
in a particular 15-minute collection interval reaches/exceeds in a particular 15-minute collection interval reaches/exceeds
this value, a hdsl2ShdslPerfUASThreshTrap will be generated. this value, a hdsl2ShdslPerfUASThreshTrap will be generated.
One trap will be sent per interval per endpoint." One trap will be sent per interval per endpoint."
Expires November 8, 2000 Page [39] Expires April 30, 2001 Page [39]
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 8 } ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 8 }
hdsl2ShdslEndpointAlarmConfProfileRowStatus OBJECT-TYPE hdsl2ShdslEndpointAlarmConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus SYNTAX RowStatus
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object controls creation/deletion of the associated "This object controls creation/deletion of the associated
entry in this table as per the semantics of RowStatus." entry in this table as per the semantics of RowStatus."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 9 } ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 9 }
skipping to change at line 2186 skipping to change at line 2186
hdsl2ShdslEndpointThreshSNRMargin hdsl2ShdslEndpointThreshSNRMargin
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This trap indicates that the SNR margin threshold (as per the "This trap indicates that the SNR margin threshold (as per the
hdsl2ShdslEndpointThreshSNRMargin value) has been hdsl2ShdslEndpointThreshSNRMargin value) has been
reached/exceeded for the HDSL2/SHDSL segment endpoint identified reached/exceeded for the HDSL2/SHDSL segment endpoint identified
by the ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, and by the ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, and
hdsl2ShdslEndpointWirePair values." hdsl2ShdslEndpointWirePair values."
Expires November 8, 2000 Page [40] Expires April 30, 2001 Page [40]
::= { hdsl2ShdslTrapsPrefix 2 } ::= { hdsl2ShdslTrapsPrefix 2 }
hdsl2ShdslPerfESThreshTrap NOTIFICATION-TYPE hdsl2ShdslPerfESThreshTrap NOTIFICATION-TYPE
OBJECTS OBJECTS
{ {
ifIndex, ifIndex,
hdsl2ShdslInvIndex, hdsl2ShdslInvIndex,
hdsl2ShdslEndpointSide, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2ShdslEndpointWirePair,
hdsl2ShdslEndpointCurr15MinES, hdsl2ShdslEndpointCurr15MinES,
skipping to change at line 2241 skipping to change at line 2241
hdsl2ShdslInvIndex, hdsl2ShdslInvIndex,
hdsl2ShdslEndpointSide, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2ShdslEndpointWirePair,
hdsl2ShdslEndpointCurr15MinCRCanomalies, hdsl2ShdslEndpointCurr15MinCRCanomalies,
hdsl2ShdslEndpointThreshCRCanomalies hdsl2ShdslEndpointThreshCRCanomalies
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This trap indicates that the CRC anomalies threshold (as "This trap indicates that the CRC anomalies threshold (as
Expires November 8, 2000 Page [41] Expires April 30, 2001 Page [41]
per the hdsl2ShdslEndpointThreshCRCanomalies value) has been per the hdsl2ShdslEndpointThreshCRCanomalies value) has been
reached/exceeded for the HDSL2/SHDSL Segment Endpoint identified reached/exceeded for the HDSL2/SHDSL Segment Endpoint identified
by the ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, and by the ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, and
hdsl2ShdslEndpointWirePair values." hdsl2ShdslEndpointWirePair values."
::= { hdsl2ShdslTrapsPrefix 5 } ::= { hdsl2ShdslTrapsPrefix 5 }
hdsl2ShdslPerfLOSWSThreshTrap NOTIFICATION-TYPE hdsl2ShdslPerfLOSWSThreshTrap NOTIFICATION-TYPE
OBJECTS OBJECTS
{ {
ifIndex, ifIndex,
skipping to change at line 2296 skipping to change at line 2296
hdsl2ShdslSpanInvalidNumRepeaters NOTIFICATION-TYPE hdsl2ShdslSpanInvalidNumRepeaters NOTIFICATION-TYPE
OBJECTS OBJECTS
{ {
ifIndex, ifIndex,
hdsl2ShdslConfNumRepeaters hdsl2ShdslConfNumRepeaters
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This trap indicates that a mismatch has been detected between "This trap indicates that a mismatch has been detected between
Expires November 8, 2000 Page [42] Expires April 30, 2001 Page [42]
the number of repeater/regenerator units configured for a the number of repeater/regenerator units configured for a
HDSL2/SHDSL line via the hdsl2ShdslConfNumRepeaters object and HDSL2/SHDSL line via the hdsl2ShdslConfNumRepeaters object and
the actual number of repeater/regenerator units discovered via the actual number of repeater/regenerator units discovered via
the EOC." the EOC."
::= { hdsl2ShdslTrapsPrefix 8 } ::= { hdsl2ShdslTrapsPrefix 8 }
hdsl2ShdslLoopbackFailure NOTIFICATION-TYPE hdsl2ShdslLoopbackFailure NOTIFICATION-TYPE
OBJECTS OBJECTS
{ {
ifIndex, ifIndex,
skipping to change at line 2350 skipping to change at line 2350
hdsl2ShdslMaintenanceGroup, hdsl2ShdslMaintenanceGroup,
hdsl2ShdslEndpointAlarmConfGroup, hdsl2ShdslEndpointAlarmConfGroup,
hdsl2ShdslNotificationGroup hdsl2ShdslNotificationGroup
} }
GROUP hdsl2ShdslInventoryShdslGroup GROUP hdsl2ShdslInventoryShdslGroup
DESCRIPTION DESCRIPTION
"Support for this group is only required for implementations "Support for this group is only required for implementations
supporting SHDSL lines." supporting SHDSL lines."
Expires November 8, 2000 Page [43] Expires April 30, 2001 Page [43]
GROUP hdsl2ShdslSpanShdslStatusGroup GROUP hdsl2ShdslSpanShdslStatusGroup
DESCRIPTION DESCRIPTION
"Support for this group is only required for implementations "Support for this group is only required for implementations
supporting SHDSL lines." supporting SHDSL lines."
GROUP hdsl2ShdslSpanConfProfileGroup GROUP hdsl2ShdslSpanConfProfileGroup
DESCRIPTION DESCRIPTION
"Support for this group is only required for implementations "Support for this group is only required for implementations
supporting SHDSL lines." supporting SHDSL lines."
skipping to change at line 2406 skipping to change at line 2406
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects for retrieving SHDSL-specific "This group supports objects for retrieving SHDSL-specific
inventory information." inventory information."
::= { hdsl2ShdslGroups 3 } ::= { hdsl2ShdslGroups 3 }
hdsl2ShdslSpanShdslStatusGroup OBJECT-GROUP hdsl2ShdslSpanShdslStatusGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
Expires November 8, 2000 Page [44] Expires April 30, 2001 Page [44]
hdsl2ShdslStatusMaxAttainableLineRate, hdsl2ShdslStatusMaxAttainableLineRate,
hdsl2ShdslStatusActualLineRate, hdsl2ShdslStatusActualLineRate,
hdsl2ShdslStatusTransmissionModeCurrent hdsl2ShdslStatusTransmissionModeCurrent
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects for retrieving SHDSL-specific "This group supports objects for retrieving SHDSL-specific
span related status." span related status."
::= { hdsl2ShdslGroups 4 } ::= { hdsl2ShdslGroups 4 }
skipping to change at line 2461 skipping to change at line 2461
hdsl2ShdslEndpointCurrGroup OBJECT-GROUP hdsl2ShdslEndpointCurrGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
hdsl2ShdslEndpointSide, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2ShdslEndpointWirePair,
hdsl2ShdslEndpointCurrAtn, hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointCurrSnrMgn, hdsl2ShdslEndpointCurrSnrMgn,
hdsl2ShdslEndpointCurrStatus, hdsl2ShdslEndpointCurrStatus,
hdsl2ShdslEndpointES, hdsl2ShdslEndpointES,
Expires November 8, 2000 Page [45] Expires April 30, 2001 Page [45]
hdsl2ShdslEndpointSES, hdsl2ShdslEndpointSES,
hdsl2ShdslEndpointCRCanomalies, hdsl2ShdslEndpointCRCanomalies,
hdsl2ShdslEndpointLOSWS, hdsl2ShdslEndpointLOSWS,
hdsl2ShdslEndpointUAS, hdsl2ShdslEndpointUAS,
hdsl2ShdslEndpointCurr15MinTimeElapsed, hdsl2ShdslEndpointCurr15MinTimeElapsed,
hdsl2ShdslEndpointCurr15MinES, hdsl2ShdslEndpointCurr15MinES,
hdsl2ShdslEndpointCurr15MinSES, hdsl2ShdslEndpointCurr15MinSES,
hdsl2ShdslEndpointCurr15MinCRCanomalies, hdsl2ShdslEndpointCurr15MinCRCanomalies,
hdsl2ShdslEndpointCurr15MinLOSWS, hdsl2ShdslEndpointCurr15MinLOSWS,
hdsl2ShdslEndpointCurr15MinUAS, hdsl2ShdslEndpointCurr15MinUAS,
skipping to change at line 2516 skipping to change at line 2516
hdsl2Shdsl1DayIntervalES, hdsl2Shdsl1DayIntervalES,
hdsl2Shdsl1DayIntervalSES, hdsl2Shdsl1DayIntervalSES,
hdsl2Shdsl1DayIntervalCRCanomalies, hdsl2Shdsl1DayIntervalCRCanomalies,
hdsl2Shdsl1DayIntervalLOSWS, hdsl2Shdsl1DayIntervalLOSWS,
hdsl2Shdsl1DayIntervalUAS hdsl2Shdsl1DayIntervalUAS
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects which maintain historic performance "This group supports objects which maintain historic performance
Expires November 8, 2000 Page [46] Expires April 30, 2001 Page [46]
measurements relating to segment endpoints in HDSL2/SHDSL lines measurements relating to segment endpoints in HDSL2/SHDSL lines
in 1-day intervals." in 1-day intervals."
::= { hdsl2ShdslGroups 9 } ::= { hdsl2ShdslGroups 9 }
hdsl2ShdslMaintenanceGroup OBJECT-GROUP hdsl2ShdslMaintenanceGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
hdsl2ShdslMaintLoopbackConfig, hdsl2ShdslMaintLoopbackConfig,
hdsl2ShdslMaintTipRingReversal, hdsl2ShdslMaintTipRingReversal,
hdsl2ShdslMaintPowerBackOff, hdsl2ShdslMaintPowerBackOff,
skipping to change at line 2571 skipping to change at line 2571
hdsl2ShdslSNRMarginCrossingTrap, hdsl2ShdslSNRMarginCrossingTrap,
hdsl2ShdslPerfESThreshTrap, hdsl2ShdslPerfESThreshTrap,
hdsl2ShdslPerfSESThreshTrap, hdsl2ShdslPerfSESThreshTrap,
hdsl2ShdslPerfCRCanomaliesThreshTrap, hdsl2ShdslPerfCRCanomaliesThreshTrap,
hdsl2ShdslPerfLOSWSThreshTrap, hdsl2ShdslPerfLOSWSThreshTrap,
hdsl2ShdslPerfUASThreshTrap, hdsl2ShdslPerfUASThreshTrap,
hdsl2ShdslSpanInvalidNumRepeaters, hdsl2ShdslSpanInvalidNumRepeaters,
hdsl2ShdslLoopbackFailure hdsl2ShdslLoopbackFailure
} }
Expires November 8, 2000 Page [47] Expires April 30, 2001 Page [47]
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports traps that enable notification of "This group supports traps that enable notification of
significant events/conditions associated with HDSL2/SHDSL significant events/conditions associated with HDSL2/SHDSL
lines." lines."
::= { hdsl2ShdslGroups 12 } ::= { hdsl2ShdslGroups 12 }
hdsl2ShdslSpanConfProfileGroup OBJECT-GROUP hdsl2ShdslSpanConfProfileGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
skipping to change at line 2626 skipping to change at line 2626
Philip Bergstresser (Adtran) Philip Bergstresser (Adtran)
Steve Blackwell (Adtran) Steve Blackwell (Adtran)
Mark Johnson (Red Point) Mark Johnson (Red Point)
Sharon Mantin (Orckit) Sharon Mantin (Orckit)
Moti Morgenstern (ECI) Moti Morgenstern (ECI)
Expires November 8, 2000 Page [48] Expires April 30, 2001 Page [48]
Raymond Murphy (Ericsson) Raymond Murphy (Ericsson)
Katy Sherman (Orckit) Katy Sherman (Orckit)
Mike Sneed (Pulse) Mike Sneed (Pulse)
9. References 9. References
[1] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for [1] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for
skipping to change at line 2682 skipping to change at line 2682
[11] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message [11] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message
Processing and Dispatching for the Simple Network Management Processing and Dispatching for the Simple Network Management
Protocol (SNMP)", RFC 2572, April 1999. Protocol (SNMP)", RFC 2572, April 1999.
[12] Blumenthal, U., and B. Wijnen, "User-based Security Model (USM) [12] Blumenthal, U., and B. Wijnen, "User-based Security Model (USM)
for version 3 of the Simple Network Management Protocol (SNMPv3)", for version 3 of the Simple Network Management Protocol (SNMPv3)",
RFC 2574, April 1999. RFC 2574, April 1999.
[13] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol [13] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol
Expires November 8, 2000 Page [49] Expires April 30, 2001 Page [49]
Operations for Version 2 of the Simple Network Management Protocol Operations for Version 2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1905, January 1996. (SNMPv2)", RFC 1905, January 1996.
[14] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC [14] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC
2573, April 1999. 2573, April 1999.
[15] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based Access [15] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based Access
Control Model (VACM) for the Simple Network Management Protocol Control Model (VACM) for the Simple Network Management Protocol
(SNMP)", RFC 2575, April 1999. (SNMP)", RFC 2575, April 1999.
skipping to change at line 2738 skipping to change at line 2738
IETF's procedures with respect to rights in standards-track and IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11. Copies of standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances of claims of rights made available for publication and any assurances of
licenses to be made available, or the result of an attempt made to licenses to be made available, or the result of an attempt made to
obtain a general license or permission for the use of such obtain a general license or permission for the use of such
proprietary rights by implementors or users of this specification can proprietary rights by implementors or users of this specification can
be obtained from the IETF Secretariat. be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any The IETF invites any interested party to bring to its attention any
Expires November 8, 2000 Page [50] Expires April 30, 2001 Page [50]
copyrights, patents or patent applications, or other proprietary copyrights, patents or patent applications, or other proprietary
rights which may cover technology that may be required to practice rights which may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive this standard. Please address the information to the IETF Executive
Director. Director.
11. Authors' Addresses 11. Authors' Addresses
Bob Ray Bob Ray
Verilink Corporation Verilink Corporation
skipping to change at line 2791 skipping to change at line 2791
The limited permissions granted above are perpetual and will not be The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns. revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Expires November 8, 2000 Page [51] Expires April 30, 2001 Page [51]
 End of changes. 

This html diff was produced by rfcdiff 1.23, available from http://www.levkowetz.com/ietf/tools/rfcdiff/