draft-ietf-adslmib-hdsl2-07.txt   draft-ietf-adslmib-hdsl2-08.txt 
INTERNET-DRAFT B. Ray INTERNET-DRAFT B. Ray
Verilink Corporation Verilink Corporation
R. Abbi R. Abbi
Alcatel Alcatel
January 2001 February 2001
Definitions of Managed Objects for HDSL2 and SHDSL Lines Definitions of Managed Objects for HDSL2 and SHDSL Lines
draft-ietf-adslmib-hdsl2-07.txt draft-ietf-adslmib-hdsl2-08.txt
Status of this Memo Status of this Memo
This document is an Internet-Draft and is in full conformance with This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC 2026. all provisions of Section 10 of RFC 2026.
Internet-Drafts are working documents of the Internet Engineering Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that other Task Force (IETF), its areas, and its working groups. Note that other
groups may also distribute working documents as Internet-Drafts. groups may also distribute working documents as Internet-Drafts.
skipping to change at line 41 skipping to change at line 41
To view the entire list of current Internet-Drafts, please check the To view the entire list of current Internet-Drafts, please check the
"1id-abstracts.txt" listing contained in the Internet-Drafts Shadow "1id-abstracts.txt" listing contained in the Internet-Drafts Shadow
Directories on ftp.is.co.za (Africa), ftp.nordu.net (Northern Directories on ftp.is.co.za (Africa), ftp.nordu.net (Northern
Europe), ftp.nis.garr.it (Southern Europe), munnari.oz.au (Pacific Europe), ftp.nis.garr.it (Southern Europe), munnari.oz.au (Pacific
Rim), ftp.ietf.org (US East Coast), or ftp.isi.edu (US West Coast). Rim), ftp.ietf.org (US East Coast), or ftp.isi.edu (US West Coast).
Copyright Notice Copyright Notice
Copyright (C) The Internet Society (2001). All Rights Reserved. Copyright (C) The Internet Society (2001). All Rights Reserved.
Expires July 26, 2001 Page [1] Expires August 12, 2001 Page [1]
Table of Contents Table of Contents
1. Abstract .................................................. 2 1. Abstract .................................................. 2
2. The SNMPv2 Network Management Framework ................... 2 2. The SNMPv2 Network Management Framework ................... 2
3. Introduction .............................................. 3 3. Introduction .............................................. 3
3.1 Relationship of the MIB with Standard MIBs ................ 4 3.1 Relationship of the MIB with Standard MIBs ................ 4
4. Conventions used in the MIB ............................... 5 4. Conventions used in the MIB ............................... 5
4.1 Naming Conventions ........................................ 5 4.1 Naming Conventions ........................................ 5
4.2 Textual Conventions ....................................... 5 4.2 Textual Conventions ....................................... 5
skipping to change at line 97 skipping to change at line 97
The second version, called SMIv2, is described in STD 58, RFC The second version, called SMIv2, is described in STD 58, RFC
2578 [5], STD 58, RFC 2579 [6] and STD 58, RFC 2580 [7]. 2578 [5], STD 58, RFC 2579 [6] and STD 58, RFC 2580 [7].
o Message protocols for transferring management information. The o Message protocols for transferring management information. The
first version of the SNMP message protocol is called SNMPv1 and first version of the SNMP message protocol is called SNMPv1 and
described in STD 15, RFC 1157 [8]. A second version of the SNMP described in STD 15, RFC 1157 [8]. A second version of the SNMP
message protocol, which is not an Internet standards track message protocol, which is not an Internet standards track
protocol, is called SNMPv2c and described in RFC 1901 [9] and protocol, is called SNMPv2c and described in RFC 1901 [9] and
RFC 1906 [10]. The third version of the message protocol is RFC 1906 [10]. The third version of the message protocol is
Expires July 26, 2001 Page [2] Expires August 12, 2001 Page [2]
called SNMPv3 and described in RFC 1906 [10], RFC 2572 [11] and called SNMPv3 and described in RFC 1906 [10], RFC 2572 [11] and
RFC 2574 [12]. RFC 2574 [12].
o Protocol operations for accessing management information. The o Protocol operations for accessing management information. The
first set of protocol operations and associated PDU formats is first set of protocol operations and associated PDU formats is
described in STD 15, RFC 1157 [8]. A second set of protocol described in STD 15, RFC 1157 [8]. A second set of protocol
operations and associated PDU formats is described in RFC 1905 operations and associated PDU formats is described in RFC 1905
[13]. [13].
o A set of fundamental applications described in RFC 2573 [14] o A set of fundamental applications described in RFC 2573 [14]
skipping to change at line 152 skipping to change at line 152
the object type. the object type.
3. Introduction 3. Introduction
This document describes an SNMP MIB for managing HDSL2/SHDSL Lines. This document describes an SNMP MIB for managing HDSL2/SHDSL Lines.
The MIB is intended to be compatible with both the SNMPv1 and SNMPv2. The MIB is intended to be compatible with both the SNMPv1 and SNMPv2.
These definitions are based upon the specifications for the HDSL2 and These definitions are based upon the specifications for the HDSL2 and
SHDSL Embedded Operations Channel (EOC) as defined in ANSI SHDSL Embedded Operations Channel (EOC) as defined in ANSI
T1E1.4/2000-006 [18] and ITU G.991.2 (ex G.SHDSL) [19]. T1E1.4/2000-006 [18] and ITU G.991.2 (ex G.SHDSL) [19].
Expires July 26, 2001 Page [3] Expires August 12, 2001 Page [3]
The MIB will eventually be located in the MIB tree under MIB 2 The MIB will eventually be located in the MIB tree under MIB 2
transmission, as discussed in the MIB-2 Integration (RFC 1213 [20] and transmission, as discussed in the MIB-2 Integration (RFC 1213 [20] and
RFC 2863 [21]) section of this document. Until approved by the IETF, RFC 2863 [21]) section of this document. Until approved by the IETF,
vendors may also choose to support it under the experimental tree. vendors may also choose to support it under the experimental tree.
NOTE TO RFC EDITOR: please replace the above paragraph with the NOTE TO RFC EDITOR: please replace the above paragraph with the
following paragraph when appropriate: following paragraph when appropriate:
The MIB is located in the MIB tree under MIB-2 transmission, as The MIB is located in the MIB tree under MIB-2 transmission, as
skipping to change at line 208 skipping to change at line 208
and are indexed by ifIndex. and are indexed by ifIndex.
The following attributes are part of the mandatory ifGeneral group in The following attributes are part of the mandatory ifGeneral group in
RFC 2863 [21], and are not duplicated in the HDSL2/SHDSL Line MIB. RFC 2863 [21], and are not duplicated in the HDSL2/SHDSL Line MIB.
=================================================================== ===================================================================
ifIndex Interface index. ifIndex Interface index.
ifDescr See interfaces MIB [21]. ifDescr See interfaces MIB [21].
Expires July 26, 2001 Page [4] Expires August 12, 2001 Page [4]
ifType hdsl2(168) or shdsl(169). ifType hdsl2(168) or shdsl(169).
ifSpeed Set as appropriate. ifSpeed Set as appropriate.
(This is fixed at 1552000 for HDSL2 lines) (This is fixed at 1552000 for HDSL2 lines)
ifPhysAddress This object should have an octet string ifPhysAddress This object should have an octet string
with zero length. with zero length.
ifAdminStatus See interfaces MIB [21]. ifAdminStatus See interfaces MIB [21].
skipping to change at line 263 skipping to change at line 263
4.2. Textual Conventions 4.2. Textual Conventions
The following textual conventions are defined to reflect the line The following textual conventions are defined to reflect the line
topology in the MIB (further discussed is the following section) topology in the MIB (further discussed is the following section)
and to define the behaviour of the statistics to be maintained and to define the behaviour of the statistics to be maintained
by an agent. by an agent.
o Hdsl2ShdslUnitId : o Hdsl2ShdslUnitId :
Expires July 26, 2001 Page [5] Expires August 12, 2001 Page [5]
This attribute uniquely identifies each unit in a HDSL2/SHDSL span. This attribute uniquely identifies each unit in a HDSL2/SHDSL span.
It mirrors the EOC addressing mechanism: It mirrors the EOC addressing mechanism:
xtuC(1) - CO terminal unit xtuC(1) - CO terminal unit
xtuR(2) - CPE terminal unit xtuR(2) - CPE terminal unit
xru1(3) .. xru8(10) - regenerators, numbered from xru1(3) .. xru8(10) - regenerators, numbered from
central office side central office side
o Hdsl2ShdslUnitSide: o Hdsl2ShdslUnitSide:
This attribute references the two sides of a unit: This attribute references the two sides of a unit:
skipping to change at line 317 skipping to change at line 317
This attribute defines the behaviour of the alarm thresholds found This attribute defines the behaviour of the alarm thresholds found
in the MIB. in the MIB.
4.3. Structure 4.3. Structure
The MIB is structured into following MIB groups: The MIB is structured into following MIB groups:
o Span Configuration Group: o Span Configuration Group:
Expires July 26, 2001 Page [6] Expires August 12, 2001 Page [6]
This group supports MIB objects for configuring parameters for This group supports MIB objects for configuring parameters for
the HDSL2/SHDSL span. It contains the following table(s): the HDSL2/SHDSL span. It contains the following table(s):
- hdsl2ShdslSpanConfTable - hdsl2ShdslSpanConfTable
o Span Status Group: o Span Status Group:
This group supports MIB objects for retrieving span status This group supports MIB objects for retrieving span status
information. It contains the following table(s): information. It contains the following table(s):
skipping to change at line 372 skipping to change at line 372
o Segment Endpoint 1-Day Interval Status/Performance Group: o Segment Endpoint 1-Day Interval Status/Performance Group:
This group supports MIB objects that provide historic This group supports MIB objects that provide historic
status/performance information relating to segment endpoints status/performance information relating to segment endpoints
in 1-day intervals. It contains the following table(s): in 1-day intervals. It contains the following table(s):
- hdsl2Shdsl1DayIntervalTable - hdsl2Shdsl1DayIntervalTable
o Maintenance Group: o Maintenance Group:
Expires July 26, 2001 Page [7] Expires August 12, 2001 Page [7]
This group supports MIB objects for performing maintenance This group supports MIB objects for performing maintenance
operations such as loopbacks for HDSL2/SHDSL lines. It contains operations such as loopbacks for HDSL2/SHDSL lines. It contains
the following table(s): the following table(s):
- hdsl2ShdslEndpointMaintTable - hdsl2ShdslEndpointMaintTable
- hdsl2ShdslUnitMaintTable - hdsl2ShdslUnitMaintTable
o Span Configuration Profile Group: o Span Configuration Profile Group:
This group supports MIB objects for defining configuration profiles This group supports MIB objects for defining configuration profiles
skipping to change at line 424 skipping to change at line 424
- hdsl2ShdslnoNeighborPresent - hdsl2ShdslnoNeighborPresent
- hdsl2ShdsllocalPowerLoss - hdsl2ShdsllocalPowerLoss
4.3.1 Line Topology 4.3.1 Line Topology
An HDSL2/SHDSL Line consists of a minimum of two units - xtuC (the An HDSL2/SHDSL Line consists of a minimum of two units - xtuC (the
central termination unit) and an xtuR (the remote termination unit). central termination unit) and an xtuR (the remote termination unit).
The line may optionally support up to 8 repeater/regenerator units The line may optionally support up to 8 repeater/regenerator units
(xru) as shown in the figure below. (xru) as shown in the figure below.
Expires July 26, 2001 Page [8] Expires August 12, 2001 Page [8]
<-- Network Side Customer Side --> <-- Network Side Customer Side -->
|</////////////////// HDSL2/SHDSL Span ////////////////////>| |</////////////////// HDSL2/SHDSL Span ////////////////////>|
<~~~> <~~~> HDSL2/SHDSL Segments <~~~> <~~~> <~~~> HDSL2/SHDSL Segments <~~~>
+-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+
+ C=1=N C=1=N C=..1..=N C=1=N + + C=1=N C=1=N C=..1..=N C=1=N +
| xtuC | | xru1 | | xru2 | | xru8 | | xtuR | | xtuC | | xru1 | | xru2 | | xru8 | | xtuR |
+ C=2=N C=2=N C=..2..=N C=2=N + + C=2=N C=2=N C=..2..=N C=2=N +
skipping to change at line 478 skipping to change at line 478
4.5. Profiles 4.5. Profiles
As a managed node can handle a large number of xUs, (e.g., hundreds As a managed node can handle a large number of xUs, (e.g., hundreds
or perhaps thousands of lines), provisioning every parameter on every or perhaps thousands of lines), provisioning every parameter on every
xU may become burdensome. Moreover, most lines are provisioned xU may become burdensome. Moreover, most lines are provisioned
identically; with the same set of parameters. To simplify the identically; with the same set of parameters. To simplify the
provisioning process, this MIB makes use of profiles. A profile is a provisioning process, this MIB makes use of profiles. A profile is a
set of parameters that can be shared by multiple lines using the same set of parameters that can be shared by multiple lines using the same
Expires July 26, 2001 Page [9] Expires August 12, 2001 Page [9]
configuration. configuration.
The following profiles are used in this MIB: The following profiles are used in this MIB:
o Span Configuration Profiles - Span configuration profiles contain o Span Configuration Profiles - Span configuration profiles contain
parameters for configuring HDSL2/SHDSL spans. They are defined in parameters for configuring HDSL2/SHDSL spans. They are defined in
the hdsl2ShdslSpanConfProfileTable. Since span configuration the hdsl2ShdslSpanConfProfileTable. Since span configuration
parameters are only applicable for SHDSL, the support for span parameters are only applicable for SHDSL, the support for span
configuration profiles is optional for HDSL2 interfaces. configuration profiles is optional for HDSL2 interfaces.
skipping to change at line 534 skipping to change at line 534
Profile changes MUST take effect immediately. These changes MAY result Profile changes MUST take effect immediately. These changes MAY result
in a restart (hard reset or soft restart) of the units on the line. in a restart (hard reset or soft restart) of the units on the line.
4.6. Traps 4.6. Traps
The ability to generate the SNMP traps coldStart/WarmStart (per [21]) The ability to generate the SNMP traps coldStart/WarmStart (per [21])
which are per agent (e.g., per DSLAM in such a device), and linkUp / which are per agent (e.g., per DSLAM in such a device), and linkUp /
linkDown (per [21]) -- which are per interface (i.e., HDSL2/SHDSL line) linkDown (per [21]) -- which are per interface (i.e., HDSL2/SHDSL line)
is required. is required.
Expires July 26, 2001 Page [10] Expires August 12, 2001 Page [10]
A linkDown trap may be generated whenever any of ES, SES, CRC Anomaly, A linkDown trap may be generated whenever any of ES, SES, CRC Anomaly,
LOSW, or UAS event occurs. The corresponding linkUp trap MAY be sent LOSW, or UAS event occurs. The corresponding linkUp trap MAY be sent
when all link failure conditions are cleared. when all link failure conditions are cleared.
The traps defined in this MIB are for initialization failure and for The traps defined in this MIB are for initialization failure and for
the threshold crossings associated with the following events: ES, SES, the threshold crossings associated with the following events: ES, SES,
CRC Anomaly, LOSW, and UAS. Each threshold has its own CRC Anomaly, LOSW, and UAS. Each threshold has its own
enable/threshold value. When that value is 0, the trap is disabled. enable/threshold value. When that value is 0, the trap is disabled.
skipping to change at line 590 skipping to change at line 590
When the first second goes by and the event occurs, the current When the first second goes by and the event occurs, the current
interval bucket will be 1, which equals the threshold and the trap will interval bucket will be 1, which equals the threshold and the trap will
be sent again. be sent again.
A hdsl2ShdslSpanInvalidNumRepeaters trap may be generated following A hdsl2ShdslSpanInvalidNumRepeaters trap may be generated following
completion of the discovery phase if the number of repeaters discovered completion of the discovery phase if the number of repeaters discovered
on the line differs from the number of repeaters specified in on the line differs from the number of repeaters specified in
hdsl2ShdslSpanConfNumRepeaters. For those conditions where the number hdsl2ShdslSpanConfNumRepeaters. For those conditions where the number
of provisioned repeaters is greater than those encountered during span of provisioned repeaters is greater than those encountered during span
Expires July 26, 2001 Page [11] Expires August 12, 2001 Page [11]
discovery, all table entries associated with the nonexistant repeaters discovery, all table entries associated with the nonexistant repeaters
are to be discarded. For those conditions where the number of are to be discarded. For those conditions where the number of
provisioned repeaters is less than those encountered during span provisioned repeaters is less than those encountered during span
discovery, additional table entries are to be created using the default discovery, additional table entries are to be created using the default
span configuration profile. span configuration profile.
5. Conformance and Compliance 5. Conformance and Compliance
For both HDSL2 and SHDSL lines, the following group(s) are mandatory: For both HDSL2 and SHDSL lines, the following group(s) are mandatory:
skipping to change at line 642 skipping to change at line 642
ifIndex FROM IF-MIB ifIndex FROM IF-MIB
PerfCurrentCount, PerfCurrentCount,
PerfIntervalCount FROM PerfHist-TC-MIB PerfIntervalCount FROM PerfHist-TC-MIB
SnmpAdminString FROM SNMP-FRAMEWORK-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB
MODULE-COMPLIANCE, MODULE-COMPLIANCE,
OBJECT-GROUP, OBJECT-GROUP,
NOTIFICATION-GROUP FROM SNMPv2-CONF; NOTIFICATION-GROUP FROM SNMPv2-CONF;
hdsl2ShdslMIB MODULE-IDENTITY hdsl2ShdslMIB MODULE-IDENTITY
LAST-UPDATED "200101260000Z" -- January 26, 2001 LAST-UPDATED "200102120000Z" -- February 12, 2001
Expires July 26, 2001 Page [12] Expires August 12, 2001 Page [12]
ORGANIZATION "ADSLMIB Working Group" ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO CONTACT-INFO
" "
Bob Ray Bob Ray
Verilink Corporation Verilink Corporation
950 Explorer Blvd 950 Explorer Blvd
Huntsville, AL 35806 USA Huntsville, AL 35806 USA
skipping to change at line 700 skipping to change at line 700
"A counter associated with interface performance "A counter associated with interface performance
measurements in a current 1-day (24 hour) measurement measurements in a current 1-day (24 hour) measurement
interval. interval.
The value of this counter starts at zero at the The value of this counter starts at zero at the
beginning of an interval and is increased when beginning of an interval and is increased when
associated events occur, until the end of the associated events occur, until the end of the
1-day interval. At that time the value of the 1-day interval. At that time the value of the
counter is stored in the previous 1-day history counter is stored in the previous 1-day history
Expires July 26, 2001 Page [13] Expires August 12, 2001 Page [13]
interval, if available, and the current interval interval, if available, and the current interval
counter is restarted at zero. counter is restarted at zero.
In the case where the agent has no valid data available In the case where the agent has no valid data available
for this interval the corresponding object for this interval the corresponding object
instance is not available and upon a retrieval instance is not available and upon a retrieval
request a corresponding error message shall be request a corresponding error message shall be
returned to indicate that this instance does returned to indicate that this instance does
not exist (for example, a noSuchName error for not exist (for example, a noSuchName error for
SNMPv1 and a noSuchInstance for SNMPv2 GET SNMPv1 and a noSuchInstance for SNMPv2 GET
skipping to change at line 755 skipping to change at line 755
"This convention defines a range of values "This convention defines a range of values
that may be set in a fault threshold alarm that may be set in a fault threshold alarm
control. As the number of seconds in a control. As the number of seconds in a
15-minute interval numbers at most 900, objects 15-minute interval numbers at most 900, objects
of this type may have a range of 0...900, where of this type may have a range of 0...900, where
the value of 0 disables the alarm." the value of 0 disables the alarm."
SYNTAX INTEGER(0..900) SYNTAX INTEGER(0..900)
Hdsl2ShdslUnitId ::= TEXTUAL-CONVENTION Hdsl2ShdslUnitId ::= TEXTUAL-CONVENTION
Expires July 26, 2001 Page [14] Expires August 12, 2001 Page [14]
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This is the unique identification for all units "This is the unique identification for all units
in an HDSL2/SHDSL Span. It is based on the EOC in an HDSL2/SHDSL Span. It is based on the EOC
unit addressing scheme with reference to the xtuC." unit addressing scheme with reference to the xtuC."
SYNTAX INTEGER SYNTAX INTEGER
{ {
xtuC(1), xtuC(1),
xtuR(2), xtuR(2),
xru1(3), xru1(3),
skipping to change at line 809 skipping to change at line 809
Hdsl2ShdslTransmissionModeType ::= TEXTUAL-CONVENTION Hdsl2ShdslTransmissionModeType ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Contains the regional setting of the HDSL2/SHDSL span, "Contains the regional setting of the HDSL2/SHDSL span,
represented as a bit-map of possible settings. The various represented as a bit-map of possible settings. The various
bit positions are: bit positions are:
1 region 1 Indicates ITU-T G.991.2 Annex A. 1 region 1 Indicates ITU-T G.991.2 Annex A.
Expires July 26, 2001 Page [15] Expires August 12, 2001 Page [15]
2 region 2 Indicates ITU-T G.991.2 Annex B." 2 region 2 Indicates ITU-T G.991.2 Annex B."
SYNTAX Integer32 SYNTAX Integer32
-- Span Configuration Group -- Span Configuration Group
-- --
hdsl2ShdslSpanConfTable OBJECT-TYPE hdsl2ShdslSpanConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfEntry SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
skipping to change at line 864 skipping to change at line 864
hdsl2ShdslSpanConfProfile OBJECT-TYPE hdsl2ShdslSpanConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32)) SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is a pointer to a span configuration profile in "This object is a pointer to a span configuration profile in
the hdsl2ShdslSpanConfProfileTable, which applies to this span. the hdsl2ShdslSpanConfProfileTable, which applies to this span.
The value of this object is the index of the referenced profile The value of this object is the index of the referenced profile
in the hdsl2ShdslSpanConfProfileTable. Note that span in the hdsl2ShdslSpanConfProfileTable. Note that span
Expires July 26, 2001 Page [16] Expires August 12, 2001 Page [16]
configuration profiles are only applicable to SHDSL lines. configuration profiles are only applicable to SHDSL lines.
HDSL2 lines will not support this object. By default, this HDSL2 lines will not support this object. By default, this
object will have the value 'DEFVAL' (the index of the default object will have the value 'DEFVAL' (the index of the default
profile)." profile)."
::= { hdsl2ShdslSpanConfEntry 2 } ::= { hdsl2ShdslSpanConfEntry 2 }
hdsl2ShdslSpanConfAlarmProfile OBJECT-TYPE hdsl2ShdslSpanConfAlarmProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32)) SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write MAX-ACCESS read-write
STATUS current STATUS current
skipping to change at line 919 skipping to change at line 919
INDEX { ifIndex } INDEX { ifIndex }
::= { hdsl2ShdslSpanStatusTable 1 } ::= { hdsl2ShdslSpanStatusTable 1 }
Hdsl2ShdslSpanStatusEntry ::= Hdsl2ShdslSpanStatusEntry ::=
SEQUENCE SEQUENCE
{ {
hdsl2ShdslStatusNumAvailRepeaters INTEGER, hdsl2ShdslStatusNumAvailRepeaters INTEGER,
hdsl2ShdslStatusMaxAttainableLineRate Integer32, hdsl2ShdslStatusMaxAttainableLineRate Integer32,
hdsl2ShdslStatusActualLineRate Integer32, hdsl2ShdslStatusActualLineRate Integer32,
Expires July 26, 2001 Page [17] Expires August 12, 2001 Page [17]
hdsl2ShdslStatusTransmissionModeCurrent hdsl2ShdslStatusTransmissionModeCurrent
Hdsl2ShdslTransmissionModeType Hdsl2ShdslTransmissionModeType
} }
hdsl2ShdslStatusNumAvailRepeaters OBJECT-TYPE hdsl2ShdslStatusNumAvailRepeaters OBJECT-TYPE
SYNTAX INTEGER(0..8) SYNTAX INTEGER(0..8)
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Contains the actual number of repeaters/regenerators "Contains the actual number of repeaters/regenerators
skipping to change at line 973 skipping to change at line 973
hdsl2ShdslInventoryTable OBJECT-TYPE hdsl2ShdslInventoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslInventoryEntry SYNTAX SEQUENCE OF Hdsl2ShdslInventoryEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table supports retrieval of unit inventory information "This table supports retrieval of unit inventory information
available via the EOC from units in a HDSL2/SHDSL line." available via the EOC from units in a HDSL2/SHDSL line."
::= { hdsl2ShdslMibObjects 3 } ::= { hdsl2ShdslMibObjects 3 }
Expires July 26, 2001 Page [18] Expires August 12, 2001 Page [18]
hdsl2ShdslInventoryEntry OBJECT-TYPE hdsl2ShdslInventoryEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslInventoryEntry SYNTAX Hdsl2ShdslInventoryEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2ShdslInventoryTable. Each entry "An entry in the hdsl2ShdslInventoryTable. Each entry
represents inventory information for a single unit in a represents inventory information for a single unit in a
HDSL2/SHDSL line. It is indexed by the ifIndex of the HDSL2/SHDSL line. It is indexed by the ifIndex of the
HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the
skipping to change at line 1029 skipping to change at line 1029
"Vendor ID as reported in an Inventory Response message." "Vendor ID as reported in an Inventory Response message."
::= { hdsl2ShdslInventoryEntry 2 } ::= { hdsl2ShdslInventoryEntry 2 }
hdsl2ShdslInvVendorModelNumber OBJECT-TYPE hdsl2ShdslInvVendorModelNumber OBJECT-TYPE
SYNTAX DisplayString SYNTAX DisplayString
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Vendor model number as reported in an Inventory Response "Vendor model number as reported in an Inventory Response
Expires July 26, 2001 Page [19] Expires August 12, 2001 Page [19]
message." message."
::= { hdsl2ShdslInventoryEntry 3 } ::= { hdsl2ShdslInventoryEntry 3 }
hdsl2ShdslInvVendorSerialNumber OBJECT-TYPE hdsl2ShdslInvVendorSerialNumber OBJECT-TYPE
SYNTAX DisplayString SYNTAX DisplayString
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Vendor serial number as reported in an Inventory Response "Vendor serial number as reported in an Inventory Response
message." message."
skipping to change at line 1084 skipping to change at line 1084
"Vendor issue number as reported in an Inventory Response "Vendor issue number as reported in an Inventory Response
message." message."
::= { hdsl2ShdslInventoryEntry 8 } ::= { hdsl2ShdslInventoryEntry 8 }
hdsl2ShdslInvVendorSoftwareVersion OBJECT-TYPE hdsl2ShdslInvVendorSoftwareVersion OBJECT-TYPE
SYNTAX DisplayString SYNTAX DisplayString
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
Expires July 26, 2001 Page [20] Expires August 12, 2001 Page [20]
"Vendor software version as reported in an Inventory "Vendor software version as reported in an Inventory
Response message." Response message."
::= { hdsl2ShdslInventoryEntry 9 } ::= { hdsl2ShdslInventoryEntry 9 }
hdsl2ShdslInvEquipmentCode OBJECT-TYPE hdsl2ShdslInvEquipmentCode OBJECT-TYPE
SYNTAX DisplayString SYNTAX DisplayString
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Equipment code conforming to ANSI T1.213, Coded Identification "Equipment code conforming to ANSI T1.213, Coded Identification
skipping to change at line 1139 skipping to change at line 1139
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2ShdslEndpointConfTable. Each entry "An entry in the hdsl2ShdslEndpointConfTable. Each entry
represents a single segment endpoint in a HDSL2/SHDSL line. represents a single segment endpoint in a HDSL2/SHDSL line.
It is indexed by the ifIndex of the HDSL2/SHDSL line, the It is indexed by the ifIndex of the HDSL2/SHDSL line, the
UnitId of the associated unit, the side of the unit, and the UnitId of the associated unit, the side of the unit, and the
wire-pair of the associated modem." wire-pair of the associated modem."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
Expires July 26, 2001 Page [21] Expires August 12, 2001 Page [21]
hdsl2ShdslEndpointWirePair} hdsl2ShdslEndpointWirePair}
::= { hdsl2ShdslEndpointConfTable 1 } ::= { hdsl2ShdslEndpointConfTable 1 }
Hdsl2ShdslEndpointConfEntry ::= Hdsl2ShdslEndpointConfEntry ::=
SEQUENCE SEQUENCE
{ {
hdsl2ShdslEndpointSide Hdsl2ShdslUnitSide, hdsl2ShdslEndpointSide Hdsl2ShdslUnitSide,
hdsl2ShdslEndpointWirePair Hdsl2ShdslWirePair, hdsl2ShdslEndpointWirePair Hdsl2ShdslWirePair,
hdsl2ShdslEndpointAlarmConfProfile SnmpAdminString hdsl2ShdslEndpointAlarmConfProfile SnmpAdminString
} }
skipping to change at line 1175 skipping to change at line 1175
DESCRIPTION DESCRIPTION
"The wire-pair of the modem associated with this segment "The wire-pair of the modem associated with this segment
endpoint as per the Hdsl2ShdslWirePair textual convention." endpoint as per the Hdsl2ShdslWirePair textual convention."
::= { hdsl2ShdslEndpointConfEntry 2 } ::= { hdsl2ShdslEndpointConfEntry 2 }
hdsl2ShdslEndpointAlarmConfProfile OBJECT-TYPE hdsl2ShdslEndpointAlarmConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32)) SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-write MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the alarm threshold values to be "This object configures the alarm threshold values to be used
used for this segment endpoint. The values are obtained for this segment endpoint. The values are obtained from the
from the alarm configuration profile referenced by this alarm configuration profile referenced by this object. The
object. The value of this object is the index of the value of this object is the index of the referenced profile in
referenced profile in the hdsl2ShdslLineAlarmConfProfileTable, the hdsl2ShdslEndpointAlarmConf ProfileTable, or NULL (a string
or NULL (a string of length 0). If the value is NULL, the of length 0). If the value is NULL, the endpoint uses the
endpoint uses the default Alarm Configuration Profile for the default Alarm Configuration Profile for the associated span as
associated span as per the hdsl2ShdslSpanConfAlarmProfile per the hdsl2ShdslSpanConfAlarmProfile object in the
object in the hdsl2ShdslSpanConfTable. The default value of hdsl2ShdslSpanConfTable. The default value of this object is
this object is NULL." NULL."
::= { hdsl2ShdslEndpointConfEntry 3 } ::= { hdsl2ShdslEndpointConfEntry 3 }
-- Segment Endpoint Current Status/Performance Group -- Segment Endpoint Current Status/Performance Group
-- --
hdsl2ShdslEndpointCurrTable OBJECT-TYPE hdsl2ShdslEndpointCurrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointCurrEntry SYNTAX SEQUENCE OF Hdsl2ShdslEndpointCurrEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
Expires July 26, 2001 Page [22] Expires August 12, 2001 Page [22]
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table contains current status and performance information "This table contains current status and performance information
for segment endpoints in HDSL2/SHDSL Lines." for segment endpoints in HDSL2/SHDSL Lines."
::= { hdsl2ShdslMibObjects 5 } ::= { hdsl2ShdslMibObjects 5 }
hdsl2ShdslEndpointCurrEntry OBJECT-TYPE hdsl2ShdslEndpointCurrEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointCurrEntry SYNTAX Hdsl2ShdslEndpointCurrEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
skipping to change at line 1249 skipping to change at line 1249
} }
hdsl2ShdslEndpointCurrAtn OBJECT-TYPE hdsl2ShdslEndpointCurrAtn OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
UNITS "dB" UNITS "dB"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The current loop attenuation for this endpoint as "The current loop attenuation for this endpoint as
Expires July 26, 2001 Page [23] Expires August 12, 2001 Page [23]
reported in a Network or Customer Side Performance reported in a Network or Customer Side Performance
Status message." Status message."
::= { hdsl2ShdslEndpointCurrEntry 1 } ::= { hdsl2ShdslEndpointCurrEntry 1 }
hdsl2ShdslEndpointCurrSnrMgn OBJECT-TYPE hdsl2ShdslEndpointCurrSnrMgn OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
UNITS "dB" UNITS "dB"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
skipping to change at line 1304 skipping to change at line 1304
128 configInitFailure Endpoint failure during initialization 128 configInitFailure Endpoint failure during initialization
due to paired endpoint not able to due to paired endpoint not able to
support requested configuration support requested configuration
256 protocolInitFailure Endpoint failure during initialization 256 protocolInitFailure Endpoint failure during initialization
due to incompatible protocol used by due to incompatible protocol used by
the paired endpoint. the paired endpoint.
512 noNeighborPresent Endpoint failure during initialization 512 noNeighborPresent Endpoint failure during initialization
Expires July 26, 2001 Page [24] Expires August 12, 2001 Page [24]
due to no activation sequence detected due to no activation sequence detected
from paired endpoint. from paired endpoint.
1024 loopbackActive A loopback is currently active at this 1024 loopbackActive A loopback is currently active at this
Segment Endpoint. Segment Endpoint.
This is intended to supplement ifOperStatus." This is intended to supplement ifOperStatus."
::= { hdsl2ShdslEndpointCurrEntry 3 } ::= { hdsl2ShdslEndpointCurrEntry 3 }
hdsl2ShdslEndpointES OBJECT-TYPE hdsl2ShdslEndpointES OBJECT-TYPE
skipping to change at line 1359 skipping to change at line 1359
"Count of Loss of Sync Word (LOSW) Seconds on this endpoint "Count of Loss of Sync Word (LOSW) Seconds on this endpoint
since the xU was last restarted." since the xU was last restarted."
::= { hdsl2ShdslEndpointCurrEntry 7 } ::= { hdsl2ShdslEndpointCurrEntry 7 }
hdsl2ShdslEndpointUAS OBJECT-TYPE hdsl2ShdslEndpointUAS OBJECT-TYPE
SYNTAX Counter32 SYNTAX Counter32
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
Expires July 26, 2001 Page [25] Expires August 12, 2001 Page [25]
DESCRIPTION DESCRIPTION
"Count of Unavailable Seconds (UAS) on this endpoint since "Count of Unavailable Seconds (UAS) on this endpoint since
the xU was last restarted." the xU was last restarted."
::= { hdsl2ShdslEndpointCurrEntry 8 } ::= { hdsl2ShdslEndpointCurrEntry 8 }
hdsl2ShdslEndpointCurr15MinTimeElapsed OBJECT-TYPE hdsl2ShdslEndpointCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
skipping to change at line 1414 skipping to change at line 1414
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds in the current "Count of Loss of Sync Word (LOSW) Seconds in the current
15-minute interval." 15-minute interval."
::= { hdsl2ShdslEndpointCurrEntry 13 } ::= { hdsl2ShdslEndpointCurrEntry 13 }
hdsl2ShdslEndpointCurr15MinUAS OBJECT-TYPE hdsl2ShdslEndpointCurr15MinUAS OBJECT-TYPE
Expires July 26, 2001 Page [26] Expires August 12, 2001 Page [26]
SYNTAX PerfCurrentCount SYNTAX PerfCurrentCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Unavailable Seconds (UAS) in the current 15-minute "Count of Unavailable Seconds (UAS) in the current 15-minute
interval." interval."
::= { hdsl2ShdslEndpointCurrEntry 14 } ::= { hdsl2ShdslEndpointCurrEntry 14 }
hdsl2ShdslEndpointCurr1DayTimeElapsed OBJECT-TYPE hdsl2ShdslEndpointCurr1DayTimeElapsed OBJECT-TYPE
skipping to change at line 1469 skipping to change at line 1469
"Count of CRC anomalies during the current day as measured "Count of CRC anomalies during the current day as measured
by hdsl2ShdslEndpointCurr1DayTimeElapsed." by hdsl2ShdslEndpointCurr1DayTimeElapsed."
::= { hdsl2ShdslEndpointCurrEntry 18 } ::= { hdsl2ShdslEndpointCurrEntry 18 }
hdsl2ShdslEndpointCurr1DayLOSWS OBJECT-TYPE hdsl2ShdslEndpointCurr1DayLOSWS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
Expires July 26, 2001 Page [27] Expires August 12, 2001 Page [27]
DESCRIPTION DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the current "Count of Loss of Sync Word (LOSW) Seconds during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed." day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
::= { hdsl2ShdslEndpointCurrEntry 19 } ::= { hdsl2ShdslEndpointCurrEntry 19 }
hdsl2ShdslEndpointCurr1DayUAS OBJECT-TYPE hdsl2ShdslEndpointCurr1DayUAS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
skipping to change at line 1524 skipping to change at line 1524
hdsl2Shdsl15MinIntervalLOSWS PerfIntervalCount, hdsl2Shdsl15MinIntervalLOSWS PerfIntervalCount,
hdsl2Shdsl15MinIntervalUAS PerfIntervalCount hdsl2Shdsl15MinIntervalUAS PerfIntervalCount
} }
hdsl2Shdsl15MinIntervalNumber OBJECT-TYPE hdsl2Shdsl15MinIntervalNumber OBJECT-TYPE
SYNTAX INTEGER(1..96) SYNTAX INTEGER(1..96)
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
Expires July 26, 2001 Page [28] Expires August 12, 2001 Page [28]
"Performance Data Interval number. 1 is the the most recent "Performance Data Interval number. 1 is the the most recent
previous interval; interval 96 is 24 hours ago. Intervals previous interval; interval 96 is 24 hours ago. Intervals
2..96 are optional." 2..96 are optional."
::= { hdsl2Shdsl15MinIntervalEntry 1 } ::= { hdsl2Shdsl15MinIntervalEntry 1 }
hdsl2Shdsl15MinIntervalES OBJECT-TYPE hdsl2Shdsl15MinIntervalES OBJECT-TYPE
SYNTAX PerfIntervalCount SYNTAX PerfIntervalCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
skipping to change at line 1578 skipping to change at line 1578
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Unavailable Seconds (UAS) during the interval." "Count of Unavailable Seconds (UAS) during the interval."
::= { hdsl2Shdsl15MinIntervalEntry 6 } ::= { hdsl2Shdsl15MinIntervalEntry 6 }
-- Segment Endpoint 1-Day Interval Status/Performance Group -- Segment Endpoint 1-Day Interval Status/Performance Group
-- --
Expires July 26, 2001 Page [29] Expires August 12, 2001 Page [29]
hdsl2Shdsl1DayIntervalTable OBJECT-TYPE hdsl2Shdsl1DayIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2Shdsl1DayIntervalEntry SYNTAX SEQUENCE OF Hdsl2Shdsl1DayIntervalEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table provides one row for each HDSL2/SHDSL endpoint "This table provides one row for each HDSL2/SHDSL endpoint
performance data collection interval." performance data collection interval."
::= { hdsl2ShdslMibObjects 7 } ::= { hdsl2ShdslMibObjects 7 }
skipping to change at line 1633 skipping to change at line 1633
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The amount of time in the 1-day interval over which the "The amount of time in the 1-day interval over which the
performance monitoring information is actually counted. performance monitoring information is actually counted.
This value will be the same as the interval duration except This value will be the same as the interval duration except
in a situation where performance monitoring data could not in a situation where performance monitoring data could not
be collected for any reason." be collected for any reason."
::= { hdsl2Shdsl1DayIntervalEntry 2 } ::= { hdsl2Shdsl1DayIntervalEntry 2 }
Expires July 26, 2001 Page [30] Expires August 12, 2001 Page [30]
hdsl2Shdsl1DayIntervalES OBJECT-TYPE hdsl2Shdsl1DayIntervalES OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Errored Seconds (ES) during the 1-day interval as "Count of Errored Seconds (ES) during the 1-day interval as
measured by hdsl2Shdsl1DayIntervalMoniSecs." measured by hdsl2Shdsl1DayIntervalMoniSecs."
::= { hdsl2Shdsl1DayIntervalEntry 3 } ::= { hdsl2Shdsl1DayIntervalEntry 3 }
skipping to change at line 1689 skipping to change at line 1689
"Count of Unavailable Seconds (UAS) during the 1-day interval "Count of Unavailable Seconds (UAS) during the 1-day interval
as measured by hdsl2Shdsl1DayIntervalMoniSecs." as measured by hdsl2Shdsl1DayIntervalMoniSecs."
::= { hdsl2Shdsl1DayIntervalEntry 7 } ::= { hdsl2Shdsl1DayIntervalEntry 7 }
-- Maintenance Group -- Maintenance Group
-- --
hdsl2ShdslEndpointMaintTable OBJECT-TYPE hdsl2ShdslEndpointMaintTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointMaintEntry SYNTAX SEQUENCE OF Hdsl2ShdslEndpointMaintEntry
Expires July 26, 2001 Page [31] Expires August 12, 2001 Page [31]
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table supports maintenance operations (eg. loopbacks) "This table supports maintenance operations (eg. loopbacks)
to be performed on HDSL2/SHDSL segment endpoints." to be performed on HDSL2/SHDSL segment endpoints."
::= { hdsl2ShdslMibObjects 8 } ::= { hdsl2ShdslMibObjects 8 }
hdsl2ShdslEndpointMaintEntry OBJECT-TYPE hdsl2ShdslEndpointMaintEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointMaintEntry SYNTAX Hdsl2ShdslEndpointMaintEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
skipping to change at line 1744 skipping to change at line 1744
SYNTAX INTEGER SYNTAX INTEGER
{ {
normal(1), normal(1),
reversed(2) reversed(2)
} }
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object indicates the state of the tip/ring pair at "This object indicates the state of the tip/ring pair at
Expires July 26, 2001 Page [32] Expires August 12, 2001 Page [32]
the associated segment endpoint." the associated segment endpoint."
::= { hdsl2ShdslEndpointMaintEntry 2 } ::= { hdsl2ShdslEndpointMaintEntry 2 }
hdsl2ShdslMaintPowerBackOff OBJECT-TYPE hdsl2ShdslMaintPowerBackOff OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
default(1), default(1),
enhanced(2) enhanced(2)
} }
MAX-ACCESS read-write MAX-ACCESS read-write
skipping to change at line 1799 skipping to change at line 1799
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2ShdslUnitMaintTable. Each entry "An entry in the hdsl2ShdslUnitMaintTable. Each entry
corresponds to a single unit, and is indexed by the corresponds to a single unit, and is indexed by the
ifIndex of the HDSL2/SHDSL line and the UnitId of the ifIndex of the HDSL2/SHDSL line and the UnitId of the
associated unit." associated unit."
INDEX { ifIndex, hdsl2ShdslInvIndex } INDEX { ifIndex, hdsl2ShdslInvIndex }
::= { hdsl2ShdslUnitMaintTable 1 } ::= { hdsl2ShdslUnitMaintTable 1 }
Expires July 26, 2001 Page [33] Expires August 12, 2001 Page [33]
Hdsl2ShdslUnitMaintEntry ::= Hdsl2ShdslUnitMaintEntry ::=
SEQUENCE SEQUENCE
{ {
hdsl2ShdslMaintLoopbackTimeout Integer32, hdsl2ShdslMaintLoopbackTimeout Integer32,
hdsl2ShdslMaintUnitPowerSource INTEGER hdsl2ShdslMaintUnitPowerSource INTEGER
} }
hdsl2ShdslMaintLoopbackTimeout OBJECT-TYPE hdsl2ShdslMaintLoopbackTimeout OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
skipping to change at line 1855 skipping to change at line 1855
SYNTAX Hdsl2ShdslSpanConfProfileEntry SYNTAX Hdsl2ShdslSpanConfProfileEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Each entry corresponds to a single span configuration "Each entry corresponds to a single span configuration
profile. Each profile contains a set of span configuration profile. Each profile contains a set of span configuration
parameters. The configuration parameters in a profile are parameters. The configuration parameters in a profile are
applied to those lines referencing that profile (see the applied to those lines referencing that profile (see the
hdsl2ShdslSpanConfProfile object). Profiles may be hdsl2ShdslSpanConfProfile object). Profiles may be
Expires July 26, 2001 Page [34] Expires August 12, 2001 Page [34]
created/deleted using the row creation/deletion mechanism created/deleted using the row creation/deletion mechanism
via hdsl2ShdslSpanConfProfileRowStatus. Profiles that are via hdsl2ShdslSpanConfProfileRowStatus. Profiles that are
being referenced may not be deleted." being referenced may not be deleted."
INDEX { IMPLIED hdsl2ShdslSpanConfProfileName } INDEX { IMPLIED hdsl2ShdslSpanConfProfileName }
::= { hdsl2ShdslSpanConfProfileTable 1 } ::= { hdsl2ShdslSpanConfProfileTable 1 }
Hdsl2ShdslSpanConfProfileEntry ::= Hdsl2ShdslSpanConfProfileEntry ::=
SEQUENCE SEQUENCE
{ {
hdsl2ShdslSpanConfProfileName SnmpAdminString, hdsl2ShdslSpanConfProfileName SnmpAdminString,
hdsl2ShdslSpanConfWireInterface INTEGER, hdsl2ShdslSpanConfWireInterface INTEGER,
skipping to change at line 1910 skipping to change at line 1910
hdsl2ShdslSpanConfMinLineRate OBJECT-TYPE hdsl2ShdslSpanConfMinLineRate OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
UNITS "bps" UNITS "bps"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the minimum transmission rate for "This object configures the minimum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If the associated SHDSL Line in bits-per-second (bps). If
Expires July 26, 2001 Page [35] Expires August 12, 2001 Page [35]
the minimum line rate equals the maximum line rate the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered (hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum 'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'." line rate, the line rate is considered 'rate-adaptive'."
::= { hdsl2ShdslSpanConfProfileEntry 3 } ::= { hdsl2ShdslSpanConfProfileEntry 3 }
hdsl2ShdslSpanConfMaxLineRate OBJECT-TYPE hdsl2ShdslSpanConfMaxLineRate OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
UNITS "bps" UNITS "bps"
MAX-ACCESS read-create MAX-ACCESS read-create
skipping to change at line 1965 skipping to change at line 1965
hdsl2ShdslSpanConfRemoteEnabled OBJECT-TYPE hdsl2ShdslSpanConfRemoteEnabled OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
enabled(1), enabled(1),
disabled(2) disabled(2)
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
Expires July 26, 2001 Page [36] Expires August 12, 2001 Page [36]
"This object enables/disables support for remote management "This object enables/disables support for remote management
of the units in a SHDSL line from the STU-R via the EOC." of the units in a SHDSL line from the STU-R via the EOC."
::= { hdsl2ShdslSpanConfProfileEntry 7 } ::= { hdsl2ShdslSpanConfProfileEntry 7 }
hdsl2ShdslSpanConfPowerFeeding OBJECT-TYPE hdsl2ShdslSpanConfPowerFeeding OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
noPower(1), noPower(1),
powerFeed(2), powerFeed(2),
wettingCurrent(3) wettingCurrent(3)
skipping to change at line 2020 skipping to change at line 2020
"This object specifies the upstream current condition target SNR "This object specifies the upstream current condition target SNR
margin for a SHDSL line." margin for a SHDSL line."
::= { hdsl2ShdslSpanConfProfileEntry 11 } ::= { hdsl2ShdslSpanConfProfileEntry 11 }
hdsl2ShdslSpanConfWorstCaseTargetMarginUp OBJECT-TYPE hdsl2ShdslSpanConfWorstCaseTargetMarginUp OBJECT-TYPE
SYNTAX INTEGER(-10..21) SYNTAX INTEGER(-10..21)
UNITS "dB" UNITS "dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
Expires July 26, 2001 Page [37] Expires August 12, 2001 Page [37]
DESCRIPTION DESCRIPTION
"This object specifies the upstream worst case target SNR margin "This object specifies the upstream worst case target SNR margin
for a SHDSL line." for a SHDSL line."
::= { hdsl2ShdslSpanConfProfileEntry 12 } ::= { hdsl2ShdslSpanConfProfileEntry 12 }
hdsl2ShdslSpanConfUsedTargetMargins OBJECT-TYPE hdsl2ShdslSpanConfUsedTargetMargins OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
skipping to change at line 2075 skipping to change at line 2075
SYNTAX Hdsl2ShdslEndpointAlarmConfProfileEntry SYNTAX Hdsl2ShdslEndpointAlarmConfProfileEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Each entry corresponds to a single alarm configuration "Each entry corresponds to a single alarm configuration
profile. Each profile contains a set of parameters for setting profile. Each profile contains a set of parameters for setting
alarm thresholds for various performance attributes monitored alarm thresholds for various performance attributes monitored
at HDSL2/SHDSL segment endpoints. Profiles may be at HDSL2/SHDSL segment endpoints. Profiles may be
created/deleted using the row creation/deletion mechanism via created/deleted using the row creation/deletion mechanism via
Expires July 26, 2001 Page [38] Expires August 12, 2001 Page [38]
hdsl2ShdslEndpointAlarmConfProfileRowStatus. Profiles that hdsl2ShdslEndpointAlarmConfProfileRowStatus. Profiles that
are being referenced may not be deleted." are being referenced may not be deleted."
INDEX { IMPLIED hdsl2ShdslEndpointAlarmConfProfileName } INDEX { IMPLIED hdsl2ShdslEndpointAlarmConfProfileName }
::= { hdsl2ShdslEndpointAlarmConfProfileTable 1 } ::= { hdsl2ShdslEndpointAlarmConfProfileTable 1 }
Hdsl2ShdslEndpointAlarmConfProfileEntry ::= Hdsl2ShdslEndpointAlarmConfProfileEntry ::=
SEQUENCE SEQUENCE
{ {
hdsl2ShdslEndpointAlarmConfProfileName SnmpAdminString, hdsl2ShdslEndpointAlarmConfProfileName SnmpAdminString,
hdsl2ShdslEndpointThreshLoopAttenuation Integer32, hdsl2ShdslEndpointThreshLoopAttenuation Integer32,
skipping to change at line 2129 skipping to change at line 2129
SYNTAX Integer32 SYNTAX Integer32
UNITS "dB" UNITS "dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the SNR margin alarm threshold. "This object configures the SNR margin alarm threshold.
When the current value reaches or drops below this threshold, When the current value reaches or drops below this threshold,
a hdsl2ShdslSNRMarginCrossingTrap will be generated." a hdsl2ShdslSNRMarginCrossingTrap will be generated."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 3 } ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 3 }
Expires July 26, 2001 Page [39] Expires August 12, 2001 Page [39]
hdsl2ShdslEndpointThreshES OBJECT-TYPE hdsl2ShdslEndpointThreshES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the threshold for the number of "This object configures the threshold for the number of
errored seconds (ES) within any given 15-minute performance errored seconds (ES) within any given 15-minute performance
data collection interval. If the value of errored seconds data collection interval. If the value of errored seconds
skipping to change at line 2185 skipping to change at line 2185
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the threshold for the number of "This object configures the threshold for the number of
Loss of Sync Word (LOSW) Seconds within any given 15-minute Loss of Sync Word (LOSW) Seconds within any given 15-minute
performance data collection interval. If the value of LOSW performance data collection interval. If the value of LOSW
in a particular 15-minute collection interval reaches/exceeds in a particular 15-minute collection interval reaches/exceeds
this value, a hdsl2ShdslPerfLOSWSThreshTrap will be generated. this value, a hdsl2ShdslPerfLOSWSThreshTrap will be generated.
Expires July 26, 2001 Page [40] Expires August 12, 2001 Page [40]
One trap will be sent per interval per endpoint." One trap will be sent per interval per endpoint."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 7 } ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 7 }
hdsl2ShdslEndpointThreshUAS OBJECT-TYPE hdsl2ShdslEndpointThreshUAS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the threshold for the number of "This object configures the threshold for the number of
skipping to change at line 2240 skipping to change at line 2240
"This trap indicates that the loop attenuation threshold (as "This trap indicates that the loop attenuation threshold (as
per the hdsl2ShdslEndpointThreshLoopAttenuation value) has been per the hdsl2ShdslEndpointThreshLoopAttenuation value) has been
reached/exceeded for the HDSL2/SHDSL segment endpoint identified reached/exceeded for the HDSL2/SHDSL segment endpoint identified
by the ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, and by the ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, and
hdsl2ShdslEndpointWirePair values." hdsl2ShdslEndpointWirePair values."
::= { hdsl2ShdslTrapsPrefix 1 } ::= { hdsl2ShdslTrapsPrefix 1 }
hdsl2ShdslSNRMarginCrossingTrap NOTIFICATION-TYPE hdsl2ShdslSNRMarginCrossingTrap NOTIFICATION-TYPE
OBJECTS OBJECTS
Expires July 26, 2001 Page [41] Expires August 12, 2001 Page [41]
{ {
ifIndex, ifIndex,
hdsl2ShdslInvIndex, hdsl2ShdslInvIndex,
hdsl2ShdslEndpointSide, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2ShdslEndpointWirePair,
hdsl2ShdslEndpointCurrSnrMgn, hdsl2ShdslEndpointCurrSnrMgn,
hdsl2ShdslEndpointThreshSNRMargin hdsl2ShdslEndpointThreshSNRMargin
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
skipping to change at line 2295 skipping to change at line 2295
hdsl2ShdslEndpointThreshSES hdsl2ShdslEndpointThreshSES
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This trap indicates that the severely errored seconds threshold "This trap indicates that the severely errored seconds threshold
(as per the hdsl2ShdslEndpointThreshSES value) has been reached/ (as per the hdsl2ShdslEndpointThreshSES value) has been reached/
exceeded for the HDSL2/SHDSL Segment Endpoint identified by the exceeded for the HDSL2/SHDSL Segment Endpoint identified by the
ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, and ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, and
hdsl2ShdslEndpointWirePair values." hdsl2ShdslEndpointWirePair values."
Expires July 26, 2001 Page [42] Expires August 12, 2001 Page [42]
::= { hdsl2ShdslTrapsPrefix 4 } ::= { hdsl2ShdslTrapsPrefix 4 }
hdsl2ShdslPerfCRCanomaliesThreshTrap NOTIFICATION-TYPE hdsl2ShdslPerfCRCanomaliesThreshTrap NOTIFICATION-TYPE
OBJECTS OBJECTS
{ {
ifIndex, ifIndex,
hdsl2ShdslInvIndex, hdsl2ShdslInvIndex,
hdsl2ShdslEndpointSide, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2ShdslEndpointWirePair,
hdsl2ShdslEndpointCurr15MinCRCanomalies, hdsl2ShdslEndpointCurr15MinCRCanomalies,
skipping to change at line 2350 skipping to change at line 2350
hdsl2ShdslInvIndex, hdsl2ShdslInvIndex,
hdsl2ShdslEndpointSide, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2ShdslEndpointWirePair,
hdsl2ShdslEndpointCurr15MinUAS, hdsl2ShdslEndpointCurr15MinUAS,
hdsl2ShdslEndpointThreshUAS hdsl2ShdslEndpointThreshUAS
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This trap indicates that the unavailable seconds threshold (as "This trap indicates that the unavailable seconds threshold (as
Expires July 26, 2001 Page [42] Expires August 12, 2001 Page [42]
per the hdsl2ShdslEndpointThreshUAS value) has been reached/ per the hdsl2ShdslEndpointThreshUAS value) has been reached/
exceeded for the HDSL2/SHDSL segment endpoint identified by the exceeded for the HDSL2/SHDSL segment endpoint identified by the
ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, and ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, and
hdsl2ShdslEndpointWirePair values." hdsl2ShdslEndpointWirePair values."
::= { hdsl2ShdslTrapsPrefix 7 } ::= { hdsl2ShdslTrapsPrefix 7 }
hdsl2ShdslSpanInvalidNumRepeaters NOTIFICATION-TYPE hdsl2ShdslSpanInvalidNumRepeaters NOTIFICATION-TYPE
OBJECTS OBJECTS
{ {
ifIndex, ifIndex,
skipping to change at line 2405 skipping to change at line 2405
DESCRIPTION DESCRIPTION
"This trap indicates that the bit setting for powerBackoff "This trap indicates that the bit setting for powerBackoff
in the hdsl2ShdslEndpointCurrStatus object for this endpoint in the hdsl2ShdslEndpointCurrStatus object for this endpoint
has changed." has changed."
::= { hdsl2ShdslTrapsPrefix 10 } ::= { hdsl2ShdslTrapsPrefix 10 }
hdsl2ShdsldeviceFault NOTIFICATION-TYPE hdsl2ShdsldeviceFault NOTIFICATION-TYPE
OBJECTS OBJECTS
{ {
Expires July 26, 2001 Page [43] Expires August 12, 2001 Page [43]
ifIndex, ifIndex,
hdsl2ShdslInvIndex, hdsl2ShdslInvIndex,
hdsl2ShdslEndpointSide, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair hdsl2ShdslEndpointWirePair
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This trap indicates that the bit setting for deviceFault "This trap indicates that the bit setting for deviceFault
in the hdsl2ShdslEndpointCurrStatus object for this endpoint in the hdsl2ShdslEndpointCurrStatus object for this endpoint
has changed." has changed."
skipping to change at line 2460 skipping to change at line 2460
{ {
ifIndex, ifIndex,
hdsl2ShdslInvIndex, hdsl2ShdslInvIndex,
hdsl2ShdslEndpointSide, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair hdsl2ShdslEndpointWirePair
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This trap indicates that the bit setting for "This trap indicates that the bit setting for
Expires July 26, 2001 Page [44] Expires August 12, 2001 Page [44]
protocolInitFailure in the hdsl2ShdslEndpointCurrStatus object protocolInitFailure in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed." for this endpoint has changed."
::= { hdsl2ShdslTrapsPrefix 14 } ::= { hdsl2ShdslTrapsPrefix 14 }
hdsl2ShdslnoNeighborPresent NOTIFICATION-TYPE hdsl2ShdslnoNeighborPresent NOTIFICATION-TYPE
OBJECTS OBJECTS
{ {
ifIndex, ifIndex,
hdsl2ShdslInvIndex, hdsl2ShdslInvIndex,
hdsl2ShdslEndpointSide, hdsl2ShdslEndpointSide,
skipping to change at line 2515 skipping to change at line 2515
MODULE MODULE
MANDATORY-GROUPS MANDATORY-GROUPS
{ {
hdsl2ShdslSpanConfGroup, hdsl2ShdslSpanConfGroup,
hdsl2ShdslSpanStatusGroup, hdsl2ShdslSpanStatusGroup,
hdsl2ShdslInventoryGroup, hdsl2ShdslInventoryGroup,
hdsl2ShdslEndpointConfGroup, hdsl2ShdslEndpointConfGroup,
hdsl2ShdslEndpointCurrGroup, hdsl2ShdslEndpointCurrGroup,
hdsl2Shdsl15MinIntervalGroup, hdsl2Shdsl15MinIntervalGroup,
Expires July 26, 2001 Page [45] Expires August 12, 2001 Page [45]
hdsl2Shdsl1DayIntervalGroup, hdsl2Shdsl1DayIntervalGroup,
hdsl2ShdslMaintenanceGroup, hdsl2ShdslMaintenanceGroup,
hdsl2ShdslEndpointAlarmConfGroup, hdsl2ShdslEndpointAlarmConfGroup,
hdsl2ShdslNotificationGroup hdsl2ShdslNotificationGroup
} }
GROUP hdsl2ShdslInventoryShdslGroup GROUP hdsl2ShdslInventoryShdslGroup
DESCRIPTION DESCRIPTION
"Support for this group is only required for implementations "Support for this group is only required for implementations
supporting SHDSL lines." supporting SHDSL lines."
skipping to change at line 2570 skipping to change at line 2570
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects for retrieving span related "This group supports objects for retrieving span related
status for HDSL2/SHDSL lines." status for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 2 } ::= { hdsl2ShdslGroups 2 }
hdsl2ShdslInventoryShdslGroup OBJECT-GROUP hdsl2ShdslInventoryShdslGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
Expires July 26, 2001 Page [46] Expires August 12, 2001 Page [46]
hdsl2ShdslInvTransmissionModeCapability hdsl2ShdslInvTransmissionModeCapability
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects for retrieving SHDSL-specific "This group supports objects for retrieving SHDSL-specific
inventory information." inventory information."
::= { hdsl2ShdslGroups 3 } ::= { hdsl2ShdslGroups 3 }
hdsl2ShdslSpanShdslStatusGroup OBJECT-GROUP hdsl2ShdslSpanShdslStatusGroup OBJECT-GROUP
OBJECTS OBJECTS
skipping to change at line 2625 skipping to change at line 2625
{ {
hdsl2ShdslEndpointSide, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2ShdslEndpointWirePair,
hdsl2ShdslEndpointAlarmConfProfile hdsl2ShdslEndpointAlarmConfProfile
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects for configuring parameters for "This group supports objects for configuring parameters for
segment endpoints in HDSL2/SHDSL lines." segment endpoints in HDSL2/SHDSL lines."
Expires July 26, 2001 Page [47] Expires August 12, 2001 Page [47]
::= { hdsl2ShdslGroups 6 } ::= { hdsl2ShdslGroups 6 }
hdsl2ShdslEndpointCurrGroup OBJECT-GROUP hdsl2ShdslEndpointCurrGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
hdsl2ShdslEndpointSide, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2ShdslEndpointWirePair,
hdsl2ShdslEndpointCurrAtn, hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointCurrSnrMgn, hdsl2ShdslEndpointCurrSnrMgn,
hdsl2ShdslEndpointCurrStatus, hdsl2ShdslEndpointCurrStatus,
skipping to change at line 2680 skipping to change at line 2680
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects which maintain historic performance "This group supports objects which maintain historic performance
measurements relating to segment endpoints in HDSL2/SHDSL lines measurements relating to segment endpoints in HDSL2/SHDSL lines
in 15-minute intervals." in 15-minute intervals."
::= { hdsl2ShdslGroups 8 } ::= { hdsl2ShdslGroups 8 }
hdsl2Shdsl1DayIntervalGroup OBJECT-GROUP hdsl2Shdsl1DayIntervalGroup OBJECT-GROUP
OBJECTS OBJECTS
Expires July 26, 2001 Page [48] Expires August 12, 2001 Page [48]
{ {
hdsl2Shdsl1DayIntervalMoniSecs, hdsl2Shdsl1DayIntervalMoniSecs,
hdsl2Shdsl1DayIntervalES, hdsl2Shdsl1DayIntervalES,
hdsl2Shdsl1DayIntervalSES, hdsl2Shdsl1DayIntervalSES,
hdsl2Shdsl1DayIntervalCRCanomalies, hdsl2Shdsl1DayIntervalCRCanomalies,
hdsl2Shdsl1DayIntervalLOSWS, hdsl2Shdsl1DayIntervalLOSWS,
hdsl2Shdsl1DayIntervalUAS hdsl2Shdsl1DayIntervalUAS
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
skipping to change at line 2735 skipping to change at line 2735
DESCRIPTION DESCRIPTION
"This group supports objects that allow configuration of alarm "This group supports objects that allow configuration of alarm
thresholds for various performance parameters for HDSL2/SHDSL thresholds for various performance parameters for HDSL2/SHDSL
lines." lines."
::= { hdsl2ShdslGroups 11 } ::= { hdsl2ShdslGroups 11 }
hdsl2ShdslNotificationGroup NOTIFICATION-GROUP hdsl2ShdslNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS NOTIFICATIONS
{ {
Expires July 26, 2001 Page [49] Expires August 12, 2001 Page [49]
hdsl2ShdslLoopAttenCrossingTrap, hdsl2ShdslLoopAttenCrossingTrap,
hdsl2ShdslSNRMarginCrossingTrap, hdsl2ShdslSNRMarginCrossingTrap,
hdsl2ShdslPerfESThreshTrap, hdsl2ShdslPerfESThreshTrap,
hdsl2ShdslPerfSESThreshTrap, hdsl2ShdslPerfSESThreshTrap,
hdsl2ShdslPerfCRCanomaliesThreshTrap, hdsl2ShdslPerfCRCanomaliesThreshTrap,
hdsl2ShdslPerfLOSWSThreshTrap, hdsl2ShdslPerfLOSWSThreshTrap,
hdsl2ShdslPerfUASThreshTrap, hdsl2ShdslPerfUASThreshTrap,
hdsl2ShdslSpanInvalidNumRepeaters, hdsl2ShdslSpanInvalidNumRepeaters,
hdsl2ShdslLoopbackFailure, hdsl2ShdslLoopbackFailure,
hdsl2ShdslpowerBackoff, hdsl2ShdslpowerBackoff,
skipping to change at line 2763 skipping to change at line 2763
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports traps that enable notification of "This group supports traps that enable notification of
significant events/conditions associated with HDSL2/SHDSL significant events/conditions associated with HDSL2/SHDSL
lines." lines."
::= { hdsl2ShdslGroups 12 } ::= { hdsl2ShdslGroups 12 }
hdsl2ShdslSpanConfProfileGroup OBJECT-GROUP hdsl2ShdslSpanConfProfileGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
hdsl2ShdslSpanWireInterface, hdsl2ShdslSpanConfWireInterface,
hdsl2ShdslSpanMinLineRate, hdsl2ShdslSpanConfMinLineRate,
hdsl2ShdslSpanMaxLineRate, hdsl2ShdslSpanConfMaxLineRate,
hdsl2ShdslSpanConfPSD, hdsl2ShdslSpanConfPSD,
hdsl2ShdslSpanConfTransmissionMode, hdsl2ShdslSpanConfTransmissionMode,
hdsl2ShdslSpanRemoteEnabled, hdsl2ShdslSpanConfRemoteEnabled,
hdsl2ShdslSpanPowerFeeding, hdsl2ShdslSpanConfPowerFeeding,
hdsl2ShdslSpanConfCurrCondTargetMarginDown, hdsl2ShdslSpanConfCurrCondTargetMarginDown,
hdsl2ShdslSpanConfWorstCaseTargetMarginDown, hdsl2ShdslSpanConfWorstCaseTargetMarginDown,
hdsl2ShdslSpanConfCurrCondTargetMarginUp, hdsl2ShdslSpanConfCurrCondTargetMarginUp,
hdsl2ShdslSpanConfWorstCaseTargetMarginUp, hdsl2ShdslSpanConfWorstCaseTargetMarginUp,
hdsl2ShdslSpanConfUsedTargetMargins, hdsl2ShdslSpanConfUsedTargetMargins,
hdsl2ShdslSpanConfProfileRowStatus hdsl2ShdslSpanConfProfileRowStatus
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects that constitute configuration "This group supports objects that constitute configuration
profiles for configuring span related parameters in SHDSL profiles for configuring span related parameters in SHDSL
lines." lines."
::= { hdsl2ShdslGroups 13 } ::= { hdsl2ShdslGroups 13 }
END END
7. Security Considerations 7. Security Considerations
There are a number of management objects defined in this MIB that There are a number of management objects defined in this MIB that
Expires July 26, 2001 Page [50] Expires August 12, 2001 Page [50]
have a MAX-ACCESS clause of read-write and/or read-create. Such have a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on environment without proper protection can have a negative effect on
network operations. network operations.
No managed objects in this MIB contain sensitive information. No managed objects in this MIB contain sensitive information.
SNMPv1 by itself is not a secure environment. Even if the network SNMPv1 by itself is not a secure environment. Even if the network
skipping to change at line 2846 skipping to change at line 2846
Umberto Bonollo (NEC Australia) Umberto Bonollo (NEC Australia)
Mark Johnson (Red Point) Mark Johnson (Red Point)
Sharon Mantin (Orckit) Sharon Mantin (Orckit)
Moti Morgenstern (ECI) Moti Morgenstern (ECI)
Raymond Murphy (Ericsson) Raymond Murphy (Ericsson)
Expires July 26, 2001 Page [51] Expires August 12, 2001 Page [51]
Lee Nipper (Verilink) Lee Nipper (Verilink)
Katy Sherman (Orckit) Katy Sherman (Orckit)
Mike Sneed (ECI) Mike Sneed (ECI)
Aron Wahl (Memotec) Aron Wahl (Memotec)
Michael Wrobel (Memotec) Michael Wrobel (Memotec)
skipping to change at line 2902 skipping to change at line 2902
[10] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Transport [10] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Transport
Mappings for Version 2 of the Simple Network Management Protocol Mappings for Version 2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1906, January 1996. (SNMPv2)", RFC 1906, January 1996.
[11] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message [11] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message
Processing and Dispatching for the Simple Network Management Processing and Dispatching for the Simple Network Management
Protocol (SNMP)", RFC 2572, April 1999. Protocol (SNMP)", RFC 2572, April 1999.
[12] Blumenthal, U., and B. Wijnen, "User-based Security Model (USM) [12] Blumenthal, U., and B. Wijnen, "User-based Security Model (USM)
Expires July 26, 2001 Page [52] Expires August 12, 2001 Page [52]
for version 3 of the Simple Network Management Protocol (SNMPv3)", for version 3 of the Simple Network Management Protocol (SNMPv3)",
RFC 2574, April 1999. RFC 2574, April 1999.
[13] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol [13] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol
Operations for Version 2 of the Simple Network Management Protocol Operations for Version 2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1905, January 1996. (SNMPv2)", RFC 1905, January 1996.
[14] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC [14] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC
2573, April 1999. 2573, April 1999.
skipping to change at line 2958 skipping to change at line 2958
10. Intellectual Property Notice 10. Intellectual Property Notice
The IETF takes no position regarding the validity or scope of any The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and IETF's procedures with respect to rights in standards-track and
Expires July 26, 2001 Page [53] Expires August 12, 2001 Page [53]
standards-related documentation can be found in BCP-11. Copies of standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances of claims of rights made available for publication and any assurances of
licenses to be made available, or the result of an attempt made to licenses to be made available, or the result of an attempt made to
obtain a general license or permission for the use of such obtain a general license or permission for the use of such
proprietary rights by implementors or users of this specification can proprietary rights by implementors or users of this specification can
be obtained from the IETF Secretariat. be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary copyrights, patents or patent applications, or other proprietary
skipping to change at line 3014 skipping to change at line 3014
developing Internet standards in which case the procedures for developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than followed, or as required to translate it into languages other than
English. English.
The limited permissions granted above are perpetual and will not be The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns. revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
Expires July 26, 2001 Page [54] Expires August 12, 2001 Page [54]
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Expires July 26, 2001 Page [55] Expires August 12, 2001 Page [55]
 End of changes. 

This html diff was produced by rfcdiff 1.23, available from http://www.levkowetz.com/ietf/tools/rfcdiff/