draft-ietf-adslmib-hdsl2-09.txt   draft-ietf-adslmib-hdsl2-10.txt 
INTERNET-DRAFT B. Ray Network Working Group B. Ray
Verilink Corporation Request for Comments: xxxx Verilink Corporation
Category: Standards Track R. Abbi
R. Abbi
Alcatel Alcatel
April 2001 July 2001
Definitions of Managed Objects for HDSL2 and SHDSL Lines Definitions of Managed Objects for HDSL2 and SHDSL Lines
draft-ietf-adslmib-hdsl2-09.txt draft-ietf-adslmib-hdsl2-10.txt
Status of this Memo Status of this Memo
This document is an Internet-Draft and is in full conformance with This document specifies an Internet standards track protocol for the
all provisions of Section 10 of RFC 2026. Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Internet-Drafts are working documents of the Internet Engineering Official Protocol Standards" (STD 1) for the standardization state
Task Force (IETF), its areas, and its working groups. Note that other and status of this protocol. Distribution of this memo is unlimited.
groups may also distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
To view the entire list of current Internet-Drafts, please check the
"1id-abstracts.txt" listing contained in the Internet-Drafts Shadow
Directories on ftp.is.co.za (Africa), ftp.nordu.net (Northern
Europe), ftp.nis.garr.it (Southern Europe), munnari.oz.au (Pacific
Rim), ftp.ietf.org (US East Coast), or ftp.isi.edu (US West Coast).
Copyright Notice Copyright Notice
Copyright (C) The Internet Society (2001). All Rights Reserved. Copyright (C) The Internet Society (2001). All Rights Reserved.
Table of Contents Table of Contents
1. Abstract .................................................. 2 1. Abstract .................................................. 2
2. The SNMP Network Management Framework ..................... 2 2. The SNMP Network Management Framework ..................... 2
3. Introduction .............................................. 3 3. Introduction .............................................. 3
3.1 Relationship of the MIB with Standard MIBs ................ 3 3.1 Relationship of the HDSL2/SHDSL Line MIB to other MIBs .... 3
4. Conventions used in the MIB ............................... 4 4. Conventions used in the MIB ............................... 5
4.1 Naming Conventions ........................................ 4 4.1 Naming Conventions ........................................ 5
4.2 Textual Conventions ....................................... 4 4.2 Textual Conventions ....................................... 5
4.3 Structure ................................................. 5 4.3 Structure ................................................. 6
4.4 Counters, Interval Buckets and Thresholds ................. 8 4.4 Counters, Interval Buckets and Thresholds ................. 9
4.5 Profiles .................................................. 8 4.5 Profiles .................................................. 9
4.6 Notifications ............................................. 9 4.6 Notifications ............................................. 10
5. Conformance and Compliance ................................ 11 5. Conformance and Compliance ................................ 12
6. Definitions ............................................... 11 6. Definitions ............................................... 12
7. Security Considerations ................................... 48 7. Security Considerations ................................... 53
8. Acknowledgments ........................................... 49 8. Acknowledgments ........................................... 54
9. References ................................................ 55
Expires October 2, 2001 Page [1] 10. Intellectual Property Notice .............................. 56
11. Authors' Addresses ........................................ 57
9. References ................................................ 49 12. Full Copyright Statement .................................. 57
10. Intellectual Property Notice .............................. 51
11. Authors' Addresses ........................................ 51
12. Full Copyright Statement .................................. 52
1. Abstract 1. Abstract
This document defines an experimental portion of the Management This document defines a portion of the Management Information Base
Information Base (MIB) module for use with network management protocols (MIB) module for use with network management protocols in the
in the Internet community. In particular, it describes objects used for Internet community. In particular, it describes objects used for
managing HDSL2 and SHDSL interfaces. managing High Bit-Rate DSL - 2nd generation (HDSL2) [18] and
Single-Pair High-Speed Digital Subscriber Line (SHDSL) interfaces
[19].
This document specifies a MIB module in a manner that is both compliant This document specifies a MIB module in a manner that is both
to the SNMPv2 SMI, and semantically identical to the peer SNMPv1 compliant to the SMIv2 (STD 58 [5, 6, 7]), and semantically
definitions. identical to the peer SMIv1 definitions (STD 16 [2, 3]).
2. The SNMP Management Framework 2. The SNMP Management Framework
The SNMP Management Framework presently consists of five major The SNMP Management Framework presently consists of five major
components: components:
o An overall architecture, described in RFC 2571 [1]. o An overall architecture, described in RFC 2571 [1].
o Mechanisms for describing and naming objects and events for the o Mechanisms for describing and naming objects and events for the
purpose of management. The first version of this Structure of purpose of management. The first version of this Structure of
skipping to change at line 117 skipping to change at page 3, line 26
and the view-based access control mechanism described in RFC and the view-based access control mechanism described in RFC
2575 [15]. 2575 [15].
A more detailed introduction to the current SNMP Management Framework A more detailed introduction to the current SNMP Management Framework
can be found in RFC 2570 [16]. can be found in RFC 2570 [16].
Managed objects are accessed via a virtual information store, termed Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are the Management Information Base or MIB. Objects in the MIB are
defined using the mechanisms defined in the SMI. defined using the mechanisms defined in the SMI.
Expires October 2, 2001 Page [2]
This memo specifies a MIB module that is compliant to the SMIv2. A This memo specifies a MIB module that is compliant to the SMIv2. A
MIB conforming to the SMIv1 can be produced through the appropriate MIB conforming to the SMIv1 can be produced through the appropriate
translations. The resulting translated MIB must be semantically translations. The resulting translated MIB must be semantically
equivalent, except where objects or events are omitted because no equivalent, except where objects or events are omitted because no
translation is possible (use of Counter64). Some machine readable translation is possible (use of Counter64). Some machine readable
information in SMIv2 will be converted into textual descriptions in information in SMIv2 will be converted into textual descriptions in
SMIv1 during the translation process. However, this loss of machine SMIv1 during the translation process. However, this loss of machine
readable information is not considered to change the semantics of the readable information is not considered to change the semantics of the
MIB. MIB.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in
this document are to be interpreted as described in RFC 2119 [17]. this document are to be interpreted as described in RFC 2119 [17].
3. Introduction 3. Introduction
This document describes an SNMP MIB for managing HDSL2/SHDSL Lines. This document describes an SNMP MIB for managing HDSL2/SHDSL Lines.
These definitions are based upon the specifications for the HDSL2 and These definitions are based upon the specifications for the HDSL2 and
SHDSL Embedded Operations Channel (EOC) as defined in ANSI SHDSL Embedded Operations Channel (EOC) as defined in ANSI
T1E1.4/2000-006 [18] and ITU G.991.2 (ex G.SHDSL) [19]. T1E1.4/2000-006 [18] and ITU G.991.2 [19].
The MIB will eventually be located in the MIB tree under MIB 2 The MIB is located in the MIB tree under MIB 2 transmission, as
transmission, as discussed in the MIB-2 Integration (RFC 1213 [20] and discussed in the MIB-2 Integration (RFC 1213 [20] and RFC 2863 [21])
RFC 2863 [21]) section of this document. Until approved by the IETF, section of this document.
vendors may also choose to support it under the experimental tree.
3.1. Relationship of the HDSL2/SHDSL Line MIB with Standard MIBs 3.1. Relationship of the HDSL2/SHDSL Line MIB to other MIBs
This section outlines the relationship of this MIB with other MIBs This section outlines the relationship of this MIB with other MIBs
described in RFCs and in various degrees of "standardization". described in RFCs. Specifically, IF-MIB as presented RFC 2863 [21]
Specifically, MIB-2 as presented in RFC 1213 [20] and RFC 2863 [21]
is discussed. is discussed.
3.1.1 General MIB-2 Integration (RFCs 1213 and 2863) 3.1.1 General IF-MIB Integration (RFC 2863)
The HDSL2/SHDSL Line MIB specifies the detailed attributes of a data The HDSL2/SHDSL Line MIB specifies the detailed attributes of a data
interface. As such, it needs to integrate with RFC 2863 [21]. The interface. As such, it needs to integrate with RFC 2863 [21]. The
IANA has assigned the following ifTypes to HDSL2 and SHDSL: IANA has assigned the following ifTypes to HDSL2 and SHDSL:
IANAifType ::= TEXTUAL-CONVENTION IANAifType ::= TEXTUAL-CONVENTION
... ...
SYNTAX INTEGER { SYNTAX INTEGER {
... ...
hdsl2 (168), -- High Bit-Rate DSL, 2nd generation hdsl2 (168), -- High Bit-Rate DSL, 2nd generation
shdsl (169), -- Multirate HDSL2 shdsl (169), -- Multirate HDSL2
... ...
} }
3.1.2 Usage of ifTable 3.1.2 Usage of ifTable
The MIB branch identified by this ifType contains tables appropriate The MIB branch identified by this ifType contains tables appropriate
for this interface type. Most such tables extend the ifEntry table, for this interface type. Most such tables extend the ifEntry table,
and are indexed by ifIndex. and are indexed by ifIndex. For interfaces in systems implementing
this MIB, those table entries indexed by ifIndex MUST be persistent.
Expires October 2, 2001 Page [3]
The following attributes are part of the mandatory ifGeneral group in The following attributes are part of the mandatory ifGeneral group in
RFC 2863 [21], and are not duplicated in the HDSL2/SHDSL Line MIB. RFC 2863 [21], and are not duplicated in the HDSL2/SHDSL Line MIB.
=================================================================== ===================================================================
ifIndex Interface index. ifIndex Interface index.
ifDescr See interfaces MIB [21]. ifDescr See interfaces MIB [21].
ifType hdsl2(168) or shdsl(169). ifType hdsl2(168) or shdsl(169).
ifSpeed Set as appropriate. ifSpeed Set as appropriate.
(This is fixed at 1552000 for HDSL2 lines) (This is fixed at 1552000 for HDSL2
lines)
ifPhysAddress This object should have an octet string ifPhysAddress This object MUST have an octet string
with zero length. with zero length.
ifAdminStatus See interfaces MIB [21]. ifAdminStatus See interfaces MIB [21].
ifOperStatus See interfaces MIB [21]. ifOperStatus See interfaces MIB [21].
ifLastChange See interfaces MIB [21]. ifLastChange See interfaces MIB [21].
ifName See interfaces MIB [21]. ifName See interfaces MIB [21].
skipping to change at line 220 skipping to change at page 5, line 20
4.1. Naming Conventions 4.1. Naming Conventions
A. xtuC refers to a central site terminal unit; A. xtuC refers to a central site terminal unit;
H2TU-C for HDSL2, or STU-C for SHDSL. H2TU-C for HDSL2, or STU-C for SHDSL.
B. xtuR refers to a remote site terminal unit; B. xtuR refers to a remote site terminal unit;
H2TU-R for HDSL2, or STU-R for SHDSL. H2TU-R for HDSL2, or STU-R for SHDSL.
C. xtu refers to a terminal unit; either an xtuC or xtuR. C. xtu refers to a terminal unit; either an xtuC or xtuR.
D. xru refer to a regenerator unit; D. xru refer to a regenerator unit;
H2RU for HDSL2, or SRU for SHDSL. H2RU for HDSL2, or SRU for SHDSL.
E. xU refers to any HDSL2/SHDSL unit; either an xtu or xru. E. xU refers to any HDSL2/SHDSL unit; either an xtu or xru.
F. CRC is cyclic redundancy check. F. CRC is cyclic redundancy check [19].
G. ES means errored second. G. ES means errored second [19].
H. LOSW means loss of sync word. H. LOSW means loss of sync word [19].
I. LOSWS means LOSW seconds. I. LOSWS means LOSW seconds [19].
J. SES means severely errored second. J. SES means severely errored second [19].
K. SNR means signal-to-noise ratio. K. SNR means signal-to-noise ratio [19].
L. UAS means unavailable second. L. UAS means unavailable second [19].
4.2. Textual Conventions 4.2. Textual Conventions
Expires October 2, 2001 Page [4]
The following textual conventions are defined to reflect the line The following textual conventions are defined to reflect the line
topology in the MIB (further discussed is the following section) topology in the MIB (further discussed in the following section)
and to define the behaviour of the statistics to be maintained and to define the behavior of the statistics to be maintained
by an agent. by an agent.
o Hdsl2ShdslUnitId : o Hdsl2ShdslUnitId :
This attribute uniquely identifies each unit in a HDSL2/SHDSL span. Attributes with this syntax uniquely identify each unit in a
It mirrors the EOC addressing mechanism: HDSL2/SHDSL span. It mirrors the EOC addressing mechanism:
xtuC(1) - CO terminal unit xtuC(1) - CO terminal unit
xtuR(2) - CPE terminal unit xtuR(2) - CPE terminal unit
xru1(3) .. xru8(10) - regenerators, numbered from xru1(3) .. xru8(10) - regenerators, numbered from
central office side central office side
o Hdsl2ShdslUnitSide: o Hdsl2ShdslUnitSide:
This attribute references the two sides of a unit:
Attributes with this syntax reference the two sides of a unit:
networkSide(1) - N in figure 2, below networkSide(1) - N in figure 2, below
customerSide(2) - C in figure 2, below customerSide(2) - C in figure 2, below
o Hdsl2ShdslWirePair: o Hdsl2ShdslWirePair:
This attribute references the wire-pairs connecting the units:
Attributes with this syntax reference the wire-pairs connecting
the units:
wirePair1(1) - First pair for HDSL2/SHDSL. wirePair1(1) - First pair for HDSL2/SHDSL.
wirePair2(2) - Optional second pair for SHDSL only. wirePair2(2) - Optional second pair for SHDSL only.
o Hdsl2ShdslTransmissionModeType: o Hdsl2ShdslTransmissionModeType:
This attribute specifies the regional setting for a SHDSL line.
Specified as a BITS construct, the two mode types are:
Attributes with this syntax specify the regional setting for a
SHDSL line. Specified as a BITS construct, the two mode types are:
region1 - ITU-T G.991.2 Annex A region1 - ITU-T G.991.2 Annex A
region2 - ITU-T G.991.2 Annex B region2 - ITU-T G.991.2 Annex B
o Hdsl2ShdslPerfCurrDayCount: o Hdsl2ShdslPerfCurrDayCount:
This attribute defines the behaviour of the 1-day (24 hour) Attributes with this syntax define the behavior of the 1-day (24
gauges found in the MIB. hour) gauges found in the MIB.
o Hdsl2Shdsl1DayIntervalCount: o Hdsl2Shdsl1DayIntervalCount:
This attribute defines the behaviour of the 1-day (24 hour) Attributes with this syntax define the behavior of the 1-day (24
interval counters found in the MIB. hour) interval counters found in the MIB.
o Hdsl2ShdslPerfTimeElapsed: o Hdsl2ShdslPerfTimeElapsed:
This attribute defines the behaviour of the elapsed time counters Attributes with this syntax define the behavior of the elapsed
found in the MIB. time counters found in the MIB.
o Hdsl2ShdslPerfIntervalThreshold: o Hdsl2ShdslPerfIntervalThreshold:
This attribute defines the behaviour of the alarm thresholds found Attributes with this syntax define the behavior of the alarm
in the MIB. thresholds found in the MIB.
4.3. Structure 4.3. Structure
Expires October 2, 2001 Page [5]
The MIB is structured into following MIB groups: The MIB is structured into following MIB groups:
o Span Configuration Group: o Span Configuration Group:
This group supports MIB objects for configuring parameters for This group supports MIB objects for configuring parameters for
the HDSL2/SHDSL span. It contains the following table(s): the HDSL2/SHDSL span. It contains the following table:
- hdsl2ShdslSpanConfTable - hdsl2ShdslSpanConfTable
o Span Status Group: o Span Status Group:
This group supports MIB objects for retrieving span status This group supports MIB objects for retrieving span status
information. It contains the following table(s): information. It contains the following table:
- hdsl2ShdslSpanStatusTable - hdsl2ShdslSpanStatusTable
o Unit Inventory Group: o Unit Inventory Group:
This group supports MIB objects for retrieving unit inventory This group supports MIB objects for retrieving unit inventory
information about units in HDSL2/SHDSL lines via the EOC. It information about units in HDSL2/SHDSL lines via the EOC. It
contains the following table(s): contains the following table:
- hdsl2ShdslInventoryTable - hdsl2ShdslInventoryTable
o Segment Endpoint Configuration Group: o Segment Endpoint Configuration Group:
This group supports MIB objects for configuring parameters for This group supports MIB objects for configuring parameters for
the HDSL2/SHDSL segment endpoints. It contains the following the HDSL2/SHDSL segment endpoints. It contains the following
table(s): table:
- hdsl2ShdslEndpointConfTable - hdsl2ShdslEndpointConfTable
o Segment Endpoint Current Status/Performance Group: o Segment Endpoint Current Status/Performance Group:
This group supports MIB objects that provide the current This group supports MIB objects that provide the current
status/performance information relating to segment endpoints. status/performance information relating to segment endpoints.
It contains the following table(s): It contains the following table:
- hdsl2ShdslEndpointCurrTable - hdsl2ShdslEndpointCurrTable
o Segment Endpoint 15-Minute Interval Status/Performance Group: o Segment Endpoint 15-Minute Interval Status/Performance Group:
This group supports MIB objects that provide historic This group supports MIB objects that provide historic
status/performance information relating to segment endpoints status/performance information relating to segment endpoints
in 15-minute intervals. It contains the following table(s): in 15-minute intervals. It contains the following table:
- hdsl2Shdsl15MinIntervalTable - hdsl2Shdsl15MinIntervalTable
o Segment Endpoint 1-Day Interval Status/Performance Group: o Segment Endpoint 1-Day Interval Status/Performance Group:
This group supports MIB objects that provide historic This group supports MIB objects that provide historic
status/performance information relating to segment endpoints status/performance information relating to segment endpoints
in 1-day intervals. It contains the following table(s): in 1-day intervals. It contains the following table:
Expires October 2, 2001 Page [6]
- hdsl2Shdsl1DayIntervalTable - hdsl2Shdsl1DayIntervalTable
o Maintenance Group: o Maintenance Group:
This group supports MIB objects for performing maintenance This group supports MIB objects for performing maintenance
operations such as loopbacks for HDSL2/SHDSL lines. It contains operations such as loopbacks for HDSL2/SHDSL lines. It contains
the following table(s): the following table(s):
- hdsl2ShdslEndpointMaintTable - hdsl2ShdslEndpointMaintTable
- hdsl2ShdslUnitMaintTable - hdsl2ShdslUnitMaintTable
o Span Configuration Profile Group: o Span Configuration Profile Group:
This group supports MIB objects for defining configuration profiles This group supports MIB objects for defining configuration profiles
for HDSL2/SHDSL Spans. It contains the following table(s): for HDSL2/SHDSL Spans. It contains the following table:
- hdsl2ShdslSpanConfProfileTable - hdsl2ShdslSpanConfProfileTable
o Segment Endpoint Alarm Configuration Profile Group: o Segment Endpoint Alarm Configuration Profile Group:
This group supports MIB objects for defining alarm configuration This group supports MIB objects for defining alarm configuration
profiles for HDSL2/SHDSL Segment Endpoints. It contains the profiles for HDSL2/SHDSL Segment Endpoints. It contains the
following table(s): following table:
- hdsl2ShdslEndpointAlarmConfProfileTable - hdsl2ShdslEndpointAlarmConfProfileTable
o Notifications Group: o Notifications Group:
This group defines Notification messages supported for HDSL2/ This group defines the notifications supported for HDSL2/SHDSL
SHDSL lines. It defines the following notifications: lines:
- hdsl2ShdslLoopAttenCrossing - hdsl2ShdslLoopAttenCrossing
- hdsl2ShdslSNRMarginCrossing - hdsl2ShdslSNRMarginCrossing
- hdsl2ShdslPerfESThresh - hdsl2ShdslPerfESThresh
- hdsl2ShdslPerfSESThresh - hdsl2ShdslPerfSESThresh
- hdsl2ShdslPerfCRCanomaliesThresh - hdsl2ShdslPerfCRCanomaliesThresh
- hdsl2ShdslPerfLOSWSThresh - hdsl2ShdslPerfLOSWSThresh
- hdsl2ShdslPerfUASThresh - hdsl2ShdslPerfUASThresh
- hdsl2ShdslSpanInvalidNumRepeaters - hdsl2ShdslSpanInvalidNumRepeaters
- hdsl2ShdslLoopbackFailure - hdsl2ShdslLoopbackFailure
- hdsl2ShdslpowerBackoff - hdsl2ShdslpowerBackoff
- hdsl2ShdsldeviceFault - hdsl2ShdsldeviceFault
- hdsl2ShdsldcContinuityFault - hdsl2ShdsldcContinuityFault
- hdsl2ShdslconfigInitFailure - hdsl2ShdslconfigInitFailure
- hdsl2ShdslprotocolInitFailure - hdsl2ShdslprotocolInitFailure
- hdsl2ShdslnoNeighborPresent - hdsl2ShdslnoNeighborPresent
- hdsl2ShdsllocalPowerLoss - hdsl2ShdslLocalPowerLoss
4.3.1 Line Topology 4.3.1 Line Topology
An HDSL2/SHDSL Line consists of a minimum of two units - xtuC (the An HDSL2/SHDSL Line consists of a minimum of two units - xtuC (the
central termination unit) and an xtuR (the remote termination unit). central termination unit) and an xtuR (the remote termination unit).
The line may optionally support up to 8 repeater/regenerator units The line may optionally support up to 8 repeater/regenerator units
(xru) as shown in the figure below. (xru) as shown in the figure below.
Expires October 2, 2001 Page [7]
<-- Network Side Customer Side --> <-- Network Side Customer Side -->
|</////////////////// HDSL2/SHDSL Span ////////////////////>| |</////////////////// HDSL2/SHDSL Span ////////////////////>|
<~~~> <~~~> HDSL2/SHDSL Segments <~~~> <~~~> <~~~> HDSL2/SHDSL Segments <~~~>
+-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+
+ C=1=N C=1=N C=..1..=N C=1=N + + C=1=N C=1=N C=..1..=N C=1=N +
| xtuC | | xru1 | | xru2 | | xru8 | | xtuR | | xtuC | | xru1 | | xru2 | | xru8 | | xtuR |
+ C=2=N C=2=N C=..2..=N C=2=N + + C=2=N C=2=N C=..2..=N C=2=N +
skipping to change at line 419 skipping to change at page 9, line 4
| xtuC | | xru1 | | xru2 | | xru8 | | xtuR | | xtuC | | xru1 | | xru2 | | xru8 | | xtuR |
+ C=2=N C=2=N C=..2..=N C=2=N + + C=2=N C=2=N C=..2..=N C=2=N +
+-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+ +-------+
Key: <////> HDSL2/SHDSL Span Key: <////> HDSL2/SHDSL Span
<~~~~> HDSL2/SHDSL Segment <~~~~> HDSL2/SHDSL Segment
=1= HDSL2/SHDSL wire-pair-1 =1= HDSL2/SHDSL wire-pair-1
=2= SHDSL optional wire-pair-2 (Not applicable to HDSL2) =2= SHDSL optional wire-pair-2 (Not applicable to HDSL2)
C Customer Side Segment Endpoint (modem) C Customer Side Segment Endpoint (modem)
N Network Side Segment Endpoint (modem) N Network Side Segment Endpoint (modem)
Figure 2: General topology for an HDSL2/SHDSL Line Figure 2: General topology for an HDSL2/SHDSL Line
4.4. Counters, Interval Buckets and Thresholds 4.4. Counters, Interval Buckets and Thresholds
For SNR Margin, Loop Attenuation, ES, SES, CRC anomalies, LOSW, and For SNR Margin, Loop Attenuation, ES, SES, CRC anomalies, LOSW, and
UAS, there are event counters, current 15-minute and one (up to 96) UAS, there are event counters, current 15-minute and 0 to 96
15-minute history bucket(s) of "interval-counters", as well as 15-minute history bucket(s) of "interval-counters", as well as
current and one (up to 30) previous 1-day interval-counter(s). Each current and 0 to 30 previous 1-day interval-counter(s). Each
current 15-minute event bucket has an associated threshold current 15-minute event bucket has an associated threshold
notification. notification.
Unlike RFC 2493 [22] and RFC 2662 [23], there is no representation Unlike RFC 2493 [22] and RFC 2662 [23], there is no representation
in the MIB for invalid buckets. In those cases where the data for in the MIB for invalid buckets. In those cases where the data for
an interval is suspect or known to be invalid, the agent should an interval is suspect or known to be invalid, the agent MUST NOT
not report the interval. report the interval. If the current 15-minute event bucket is
determined to be invalid, notifications based upon the value of the
event bucket MUST NOT be generated.
Not reporting an interval will result in holes in the associated
table. For example, the table, hdsl2Shdsl15MinIntervalTable, is
indexed by { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2Shdsl15MinIntervalNumber}. If
interval 12 is determined to be invalid but intervals 11 and 13
are valid, a Get Next operation on the indices .1.1.1.1.11 would
return indices .1.1.1.1.13.
There is no requirement for an agent to ensure a fixed relationship There is no requirement for an agent to ensure a fixed relationship
between the start of a fifteen minute and any wall clock; however between the start of a fifteen minute and any wall clock; however
some implementations may align the fifteen minute intervals with some implementations may align the fifteen minute intervals with
quarter hours. Likewise, an implementation may choose to align one quarter hours. Likewise, an implementation may choose to align one
day intervals with the start of a day. day intervals with the start of a day.
Counters are not reset when an xU is reinitialized, only when the Counters are not reset when an xU is reinitialized, only when the
agent is reset or reinitialized (or under specific request outside agent is reset or reinitialized (or under specific request outside
the scope of this MIB). the scope of this MIB).
4.5. Profiles 4.5. Profiles
As a managed node can handle a large number of xUs, (e.g., hundreds As a managed node can handle a large number of xUs, (e.g., hundreds
or perhaps thousands of lines), provisioning every parameter on every or perhaps thousands of lines), provisioning every parameter on every
xU may become burdensome. Moreover, most lines are provisioned xU may become burdensome. Moreover, most lines are provisioned
identically; with the same set of parameters. To simplify the identically with the same set of parameters. To simplify the
provisioning process, this MIB makes use of profiles. A profile is a provisioning process, this MIB makes use of profiles. A profile is a
set of parameters that can be shared by multiple lines using the same set of parameters that can be shared by multiple lines using the same
configuration. configuration.
Expires October 2, 2001 Page [8]
The following profiles are used in this MIB: The following profiles are used in this MIB:
o Span Configuration Profiles - Span configuration profiles contain o Span Configuration Profiles - Span configuration profiles contain
parameters for configuring HDSL2/SHDSL spans. They are defined in parameters for configuring HDSL2/SHDSL spans. They are defined
the hdsl2ShdslSpanConfProfileTable. Since span configuration in the hdsl2ShdslSpanConfProfileTable. Since span configuration
parameters are only applicable for SHDSL, the support for span parameters are only applicable for SHDSL, the support for span
configuration profiles is optional for HDSL2 interfaces. configuration profiles is optional for HDSL2 interfaces.
Note that the configuration of the span dictates the behavior for Note that the configuration of the span dictates the behavior for
each individual segment end point in the span. If a different each individual segment end point in the span. If a different
configuration is provisioned for any given segment end point within configuration is provisioned for any given segment end point
the span, however, the new configuraiton for this segment end point within the span, however, the new configuration for this segment
will override the span configuration for this segment end point only. end point will override the span configuration for this segment
end point only.
o Segment Endpoint Alarm Configuration Profiles - These profiles o Segment Endpoint Alarm Configuration Profiles - These profiles
contain parameters for configuring alarm thresholds for HDSL2/ contain parameters for configuring alarm thresholds for HDSL2/
SHDSL segment endpoints. These profiles are defined in the SHDSL segment endpoints. These profiles are defined in the
hdsl2ShdslEndpointAlarmConfProfileTable. hdsl2ShdslEndpointAlarmConfProfileTable.
Implementations will enable the manager to dynamically create and The index value for this profile is a locally-unique
delete profiles as needed. The index of each profile is a locally- administratively assigned name for the profile having the textual
unique administratively assigned name for the profile having the convention `SnmpAdminString' (RFC 2571 [1]).
textual convention `SnmpAdminString' (RFC 2571 [1]).
One or more lines may be configured to share parameters of a single One or more lines may be configured to share parameters of a single
profile (e.g., hdsl2ShdslEndpointAlarmConfProfile = `silver') by profile (e.g., hdsl2ShdslEndpointAlarmConfProfile = `silver') by
setting its hdsl2ShdslEndpointAlarmConfProfile objects to the value of setting its hdsl2ShdslEndpointAlarmConfProfile objects to the value
this profile. If a change is made to the profile, all lines that refer of this profile. If a change is made to the profile, all lines that
to it will be reconfigured to the changed parameters. Before a profile refer to it will be reconfigured to the changed parameters. Before
can be deleted or taken out of service it must be first unreferenced a profile can be deleted or taken out of service it must be first
from all associated lines. unreferenced from all associated lines.
Implementations must provide a default profile whose name is `DEFVAL' Implementations MUST provide a default profile whose name is `DEFVAL'
for each profile type. The values of the associated parameters will be for each profile type. The values of the associated parameters will
vendor specific unless otherwise indicated in this document. Before a be vendor specific unless otherwise indicated in this document.
line's profiles have been set, these profiles will be automatically Before a line's profiles have been set, these profiles will be
used by setting hdsl2ShdslEndpointAlarmConfProfile and automatically used by setting hdsl2ShdslEndpointAlarmConfProfile and
hdsl2ShdslSpanConfProfile to `DEFVAL' where appropriate. hdsl2ShdslSpanConfProfile to `DEFVAL' where appropriate. This
default profile name, 'DEFVAL', is considered reserved in the context
of profiles defined in this MIB.
Profiles are created, assigned, and deleted dynamically using the Profiles are created, assigned, and deleted dynamically using the
profile name and profile row status in each of the four profile tables. profile name and profile row status in each of the four profile
tables.
Profile changes MUST take effect immediately. These changes MAY result Profile changes MUST take effect immediately. These changes MAY
in a restart (hard reset or soft restart) of the units on the line. result in a restart (hard reset or soft restart) of the units on the
line.
4.6. Notifications 4.6. Notifications
The ability to generate the SNMP notifications coldStart/WarmStart (per The ability to generate the SNMP notifications coldStart/WarmStart
[21]) which are per agent (e.g., per DSLAM in such a device), and (per [21]) which are per agent (e.g., per Digital Subscriber Line
linkUp/linkDown (per [21]) -- which are per interface (i.e., HDSL2/SHDSL Access Multiplexer, or DSLAM, in such a device), and linkUp/linkDown
line) is required. (per [21]) which are per interface (i.e., HDSL2/SHDSL line) is
required.
A linkDown notification may be generated whenever any of ES, SES, CRC
Anomaly, LOSW, or UAS event occurs. The corresponding linkUp
Expires October 2, 2001 Page [9]
notification MAY be sent when all link failure conditions are cleared. A linkDown notification MAY be generated whenever any of ES, SES,
CRC Anomaly, LOSW, or UAS event occurs. The corresponding linkUp
notification MAY be sent when all link failure conditions are
cleared.
The notifications defined in this MIB are for initialization failure and The notifications defined in this MIB are for initialization failure
for the threshold crossings associated with the following events: ES, and for the threshold crossings associated with the following events:
SES, CRC Anomaly, LOSW, and UAS. Each threshold has its own ES, SES, CRC Anomaly, LOSW, and UAS. Each threshold has its own
enable/threshold value. When that value is 0, the notification is enable/threshold value. When that value is 0, the notification is
disabled. disabled.
The hdsl2ShdslEndpointCurrStatus is a bitmask representing all The hdsl2ShdslEndpointCurrStatus is a bitmask representing all
outstanding error conditions associated with a particular Segment outstanding error conditions associated with a particular Segment
Endpoint. Note that since status of remote endpoints is obtained via Endpoint. Note that since status of remote endpoints is obtained via
the EOC, this information may be unavailable for units that are the EOC, this information may be unavailable for units that are
unreachable via EOC during a line error condition. Therefore, not all unreachable via EOC during a line error condition. Therefore, not
conditions may always be included in its current status. Notifications all conditions may always be included in its current status.
corresponding to the bit fields in this object are defined. Notifications corresponding to the bit fields in this object are
defined.
Two alarm conditions, SNR Margin Alarm and Loop Attenuation Alarm, Two alarm conditions, SNR Margin Alarm and Loop Attenuation Alarm,
are organized in a manner slightly different from that implied in are organized in a manner slightly different from that implied in
the EOC specifications. In the MIB, these alarm conditions are the EOC specifications. In the MIB, these alarm conditions are
tied to the two thresholds hdsl2ShdslEndpointThreshSNRMargin and tied to the two thresholds hdsl2ShdslEndpointThreshSNRMargin and
hdsl2ShdslEndpointThreshLoopAttenuation found in the hdsl2ShdslEndpointThreshLoopAttenuation found in the
hdsl2ShdslEndpointAlarmConfProfileTable. In the EOC, the alarm hdsl2ShdslEndpointAlarmConfProfileTable. In the EOC, the alarm
conditions associated with these thresholds are per-unit. In the conditions associated with these thresholds are per-unit. In the
MIB, these alarm conditions are per-endpoint. For terminal units, MIB, these alarm conditions are per-endpoint. For terminal units,
this has no impact. For repeaters, this implies an implementation this has no impact. For repeaters, this implies an implementation
variance where the agent in the terminal unit is responsible for variance where the agent in the terminal unit is responsible for
detecting a threshold crossing. As the reporting of a repeater detecting a threshold crossing. As the reporting of a repeater
detected alarm condition to the polling terminal unit occurs in detected alarm condition to the polling terminal unit occurs in
the same EOC message as the reporting of the current SNR Margin the same EOC message as the reporting of the current SNR Margin
and Loop Attenuation values, it is anticipated that this will have and Loop Attenuation values, it is anticipated that this will have
very little impact on agent implementation. very little impact on agent implementation.
A threshold notification occurs whenever the corresponding current A threshold notification occurs whenever the corresponding current
15-minute interval error counter becomes equal to, or exceeds the 15-minute interval error counter becomes equal to, or exceeds the
threshold value. One notification may be sent per interval per threshold value. One notification may be sent per interval per
interface. Since the current 15-minute counter are reset to 0 every 15 interface. Since the current 15-minute counter are reset to 0 every
minutes, if the condition persists, the notification may recur as 15 minutes, if the condition persists, the notification may recur as
often as every 15 minutes. For example, to get a notification often as every 15 minutes. For example, to get a notification
whenever a "loss of" event occurs (but at most once every 15 minutes), whenever a "loss of" event occurs (but at most once every 15
set the corresponding threshold to 1. The agent will generate a minutes), set the corresponding threshold to 1. The agent will
notification when the event originally occurs. generate a notification when the event originally occurs.
Note that the NMS may receive a linkDown notification, as well, if Note that the Network Management System, or NMS, may receive a
enabled. At the beginning of the next 15 minute interval, the counter is linkDown notification, as well, if enabled (via
reset. When the first second goes by and the event occurs, the current ifLinkUpDownTrapEnable [21]). At the beginning of the next 15 minute
interval bucket will be 1, which equals the threshold and the interval, the counter is reset. When the first second goes by and
notification will be sent again. the event occurs, the current interval bucket will be 1, which
equals the threshold and the notification will be sent again.
A hdsl2ShdslSpanInvalidNumRepeaters notification may be generated A hdsl2ShdslSpanInvalidNumRepeaters notification may be generated
following completion of the discovery phase if the number of repeaters following completion of the discovery phase if the number of
discovered on the line differs from the number of repeaters specified in repeaters discovered on the line differs from the number of repeaters
hdsl2ShdslSpanConfNumRepeaters. For those conditions where the number specified in hdsl2ShdslSpanConfNumRepeaters. For those conditions
of provisioned repeaters is greater than those encountered during span where the number of provisioned repeaters is greater than those
discovery, all table entries associated with the nonexistant repeaters encountered during span discovery, all table entries associated with
are to be discarded. For those conditions where the number of the nonexistant repeaters are to be discarded. For those conditions
where the number of provisioned repeaters is less than those
Expires October 2, 2001 Page [10] encountered during span discovery, additional table entries are to
be created using the default span configuration profile.
provisioned repeaters is less than those encountered during span
discovery, additional table entries are to be created using the default
span configuration profile.
5. Conformance and Compliance 5. Conformance and Compliance
For both HDSL2 and SHDSL lines, the following group(s) are mandatory: For both HDSL2 and SHDSL lines, the following group(s) are mandatory:
hdsl2ShdslSpanConfGroup hdsl2ShdslSpanConfGroup
hdsl2ShdslSpanStatusGroup hdsl2ShdslSpanStatusGroup
hdsl2ShdslInventoryGroup hdsl2ShdslInventoryGroup
hdsl2ShdslEndpointConfGroup hdsl2ShdslEndpointConfGroup
hdsl2Shdsl15MinIntervalGroup hdsl2Shdsl15MinIntervalGroup
skipping to change at line 607 skipping to change at page 12, line 43
HDSL2-SHDSL-LINE-MIB DEFINITIONS ::= BEGIN HDSL2-SHDSL-LINE-MIB DEFINITIONS ::= BEGIN
IMPORTS IMPORTS
MODULE-IDENTITY, MODULE-IDENTITY,
OBJECT-TYPE, OBJECT-TYPE,
Counter32, Counter32,
Gauge32, Gauge32,
NOTIFICATION-TYPE, NOTIFICATION-TYPE,
Integer32, Integer32,
experimental FROM SNMPv2-SMI transmission FROM SNMPv2-SMI
RowStatus, RowStatus,
TEXTUAL-CONVENTION FROM SNMPv2-TC TEXTUAL-CONVENTION FROM SNMPv2-TC
ifIndex FROM IF-MIB ifIndex FROM IF-MIB
PerfCurrentCount, PerfCurrentCount,
PerfIntervalCount FROM PerfHist-TC-MIB PerfIntervalCount FROM PerfHist-TC-MIB
SnmpAdminString FROM SNMP-FRAMEWORK-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB
MODULE-COMPLIANCE, MODULE-COMPLIANCE,
OBJECT-GROUP, OBJECT-GROUP,
NOTIFICATION-GROUP FROM SNMPv2-CONF; NOTIFICATION-GROUP FROM SNMPv2-CONF;
hdsl2ShdslMIB MODULE-IDENTITY hdsl2ShdslMIB MODULE-IDENTITY
LAST-UPDATED "200104020000Z" -- April 2, 2001 LAST-UPDATED "200107190000Z" -- July 19, 2001
ORGANIZATION "ADSLMIB Working Group" ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO "WG-email: XDSLMIB@LISTSERV.ECIRALEIGH.COM CONTACT-INFO "WG-email: XDSLMIB@LISTSERV.ECIRALEIGH.COM
Subscribe: LISTSERV@LISTSERV.ECIRALEIGH.COM Subscribe: LISTSERV@LISTSERV.ECIRALEIGH.COM
In Body: subscribe/signoff XDSLMIB In Body: subscribe/signoff XDSLMIB
Archive: index XDSLMIB/get <archivename> Archive: index XDSLMIB/get <archivename>
Co-chair: Dave Allan Chair: Mike Sneed
Nortel Networks
Expires October 2, 2001 Page [11]
Postal: 3500 Carling Avenue
Nepean ON K2H 8E9 Canada
Email: dallan@nortelnetworks.com
Phone: +1 613 763 6362 (ESN 393)
Co-chair: Mike Sneed
ECI Telecom ECI Telecom
Postal: 1017 Main Campus Drive Postal: 1017 Main Campus Drive
Raleigh NC 37606 Raleigh NC 27606 USA
Email: Mike.Sneed@go.ecitele.com Email: Mike.Sneed@go.ecitele.com
Phone: +1 919 513 1435 Phone: +1 919 513 1435
Co-editor: Bob Ray Co-editor: Bob Ray
Verilink Corporation Verilink Corporation
Postal: 950 Explorer Blvd Postal: 950 Explorer Blvd
Huntsville, AL 35806 USA Huntsville, AL 35806 USA
Email: bray@verilink.com Email: bray@verilink.com
Phone: +1 256 327 2380 Phone: +1 256 327 2380
Co-editor: Rajesh Abbi Co-editor: Rajesh Abbi
Alcatel USA Alcatel USA
Postal: 2912 Wake Forest Road Postal: 2912 Wake Forest Road
Raleigh, NC 27609-7860 USA Raleigh, NC 27609-7860 USA
Email: Rajesh.Abbi@usa.alcatel.com Email: Rajesh.Abbi@usa.alcatel.com
Phone: +1 919 950 6194 Phone: +1 919 850 6194
" "
DESCRIPTION DESCRIPTION
"This MIB module defines a collection of objects for managing "This MIB module defines a collection of objects for managing
HDSL2/SHDSL lines. An agent may reside at either end of the HDSL2/SHDSL lines. An agent may reside at either end of the
line, however the MIB is designed to require no management line, however the MIB is designed to require no management
communication between the modems beyond that inherent in the communication between the modems beyond that inherent in the
low-level EOC line protocol as defined in ANSI T1E1.4/2000-006 low-level EOC line protocol as defined in ANSI T1E1.4/2000-006
(for HDSL2 lines), or in ITU G.991.2 (for SHDSL lines)." (for HDSL2 lines), or in ITU G.991.2 (for SHDSL lines)."
REVISION "200104020000Z" -- April 2, 2001 REVISION "200107190000Z" -- July 19, 2001
DESCRIPTION "Initial version, published as RFC xxxx." DESCRIPTION "Initial version, published as RFC xxxx."
::= { experimental 109 } -- to be assigned by IANA ::= { transmission xxxx } -- to be assigned by IANA
hdsl2ShdslMibObjects OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 1 } hdsl2ShdslMibObjects OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 1 }
-- Textual Conventions used in this MIB -- Textual Conventions used in this MIB
-- --
Hdsl2ShdslPerfCurrDayCount ::= TEXTUAL-CONVENTION Hdsl2ShdslPerfCurrDayCount ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A gauge associated with interface performance measurements in "A gauge associated with interface performance measurements in
a current 1-day (24 hour) measurement interval. a current 1-day (24 hour) measurement interval.
The value of this gauge starts at zero at the beginning of an The value of this gauge starts at zero at the beginning of an
interval and is increased when associated events occur, until interval and is increased when associated events occur, until
the end of the 1-day interval. At that time the value of the the end of the 1-day interval. At that time the value of the
gauge is stored in the previous 1-day history interval, if gauge is stored in the previous 1-day history interval, as
available, and the current interval counter is restarted at defined in a companion object of type
Hdsl2Shdsl1DayIntevalCount, and the current interval counter
Expires October 2, 2001 Page [12] is restarted at zero.
zero.
In the case where the agent has no valid data available for In the case where the agent has no valid data available for
this interval the corresponding object instance is not this interval the corresponding object instance is not
available and upon a retrieval request a corresponding error available and upon a retrieval request a corresponding error
message shall be returned to indicate that this instance does message shall be returned to indicate that this instance does
not exist (for example, a noSuchName error for SNMPv1 and a not exist. Please note that zero is a valid value."
noSuchInstance for SNMPv2 GET operation)."
SYNTAX Gauge32 SYNTAX Gauge32
Hdsl2Shdsl1DayIntervalCount ::= TEXTUAL-CONVENTION Hdsl2Shdsl1DayIntervalCount ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A counter associated with interface performance measurements "A counter associated with interface performance measurements
during the most previous 1-day (24 hour) measurement interval. during the most previous 1-day (24 hour) measurement interval.
The value of this counter is equal to the value of the current The value of this counter is equal to the value of the current
day counter at the end of its most recent interval. day counter, as defined in a companion object of type
Hdsl2ShdslPerfCurrDayCount, at the end of its most recent
interval.
In the case where the agent has no valid data available for In the case where the agent has no valid data available for
this interval the corresponding object instance is not this interval the corresponding object instance is not
available and upon a retrieval request a corresponding error available and upon a retrieval request a corresponding error
message shall be returned to indicate that this instance does message shall be returned to indicate that this instance does
not exist (for example, a noSuchName error for SNMPv1 and a not exist."
noSuchInstance for SNMPv2 GET operation)."
SYNTAX Gauge32 SYNTAX Gauge32
Hdsl2ShdslPerfTimeElapsed ::= TEXTUAL-CONVENTION Hdsl2ShdslPerfTimeElapsed ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The number of seconds that have elapsed since the beginning of "The number of seconds that have elapsed since the beginning of
the current measurement period. If, for some reason, such as the current measurement period. If, for some reason, such as
an adjustment in the system's time-of-day clock, the current an adjustment in the system's time-of-day clock or the addition
interval exceeds the maximum value, the agent will return the of a leap second, the current interval exceeds the maximum
maximum value." value, the agent will return the maximum value.
SYNTAX Gauge32
For 15 minute intervals, the range is limited to (0..899).
For 24 hour intervals, the range is limited to (0..86399)."
SYNTAX INTEGER(0..86399)
Hdsl2ShdslPerfIntervalThreshold ::= TEXTUAL-CONVENTION Hdsl2ShdslPerfIntervalThreshold ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This convention defines a range of values that may be set in "This convention defines a range of values that may be set in
a fault threshold alarm control. As the number of seconds in a fault threshold alarm control. As the number of seconds in
a 15-minute interval numbers at most 900, objects of this type a 15-minute interval numbers at most 900, objects of this type
may have a range of 0...900, where the value of 0 disables the may have a range of 0...900, where the value of 0 disables the
alarm." alarm."
SYNTAX INTEGER(0..900) SYNTAX INTEGER(0..900)
Hdsl2ShdslUnitId ::= TEXTUAL-CONVENTION Hdsl2ShdslUnitId ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This is the unique identification for all units in a "This is the unique identification for all units in a
HDSL2/SHDSL Span. It is based on the EOC unit addressing HDSL2/SHDSL Span. It is based on the EOC unit addressing
scheme with reference to the xtuC." scheme with reference to the xtuC."
SYNTAX INTEGER SYNTAX INTEGER
{ {
xtuC(1), xtuC(1),
Expires October 2, 2001 Page [13]
xtuR(2), xtuR(2),
xru1(3), xru1(3),
xru2(4), xru2(4),
xru3(5), xru3(5),
xru4(6), xru4(6),
xru5(7), xru5(7),
xru6(8), xru6(8),
xru7(9), xru7(9),
xru8(10) xru8(10)
} }
skipping to change at line 799 skipping to change at page 16, line 14
SYNTAX BITS SYNTAX BITS
{ {
region1(0), region1(0),
region2(1) region2(1)
} }
-- Span Configuration Group -- Span Configuration Group
-- --
hdsl2ShdslSpanConfTable OBJECT-TYPE hdsl2ShdslSpanConfTable OBJECT-TYPE
Expires October 2, 2001 Page [14]
SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfEntry SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table supports overall configuration of HDSL2/SHDSL "This table supports overall configuration of HDSL2/SHDSL
Spans." Spans. Entries in this table MUST be maintained in a
persistent manner."
::= { hdsl2ShdslMibObjects 1 } ::= { hdsl2ShdslMibObjects 1 }
hdsl2ShdslSpanConfEntry OBJECT-TYPE hdsl2ShdslSpanConfEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanConfEntry SYNTAX Hdsl2ShdslSpanConfEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2ShdslSpanConfTable. Each entry "An entry in the hdsl2ShdslSpanConfTable. Each entry
represents the complete Span in a single HDSL2/SHDSL line. represents the complete Span in a single HDSL2/SHDSL line.
It is indexed by the ifIndex of the associated HDSL2/SHDSL It is indexed by the ifIndex of the associated HDSL2/SHDSL
skipping to change at line 848 skipping to change at page 17, line 9
hdsl2ShdslSpanConfProfile OBJECT-TYPE hdsl2ShdslSpanConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32)) SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is a pointer to a span configuration profile in "This object is a pointer to a span configuration profile in
the hdsl2ShdslSpanConfProfileTable, which applies to this span. the hdsl2ShdslSpanConfProfileTable, which applies to this span.
The value of this object is the index of the referenced profile The value of this object is the index of the referenced profile
in the hdsl2ShdslSpanConfProfileTable. Note that span in the hdsl2ShdslSpanConfProfileTable. Note that span
configuration profiles are only applicable to SHDSL lines. configuration profiles are only applicable to SHDSL lines.
HDSL2 lines will not support this object. By default, this HDSL2 lines MUST reference the default profile, 'DEFVAL'.
object will have the value 'DEFVAL' (the index of the default By default, this object will have the value 'DEFVAL' (the index
profile)." of the default profile).
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslSpanConfProfileTable, MUST be rejected."
::= { hdsl2ShdslSpanConfEntry 2 } ::= { hdsl2ShdslSpanConfEntry 2 }
hdsl2ShdslSpanConfAlarmProfile OBJECT-TYPE hdsl2ShdslSpanConfAlarmProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32)) SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write MAX-ACCESS read-write
Expires October 2, 2001 Page [15]
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is a pointer to an Alarm configuration profile in "This object is a pointer to an Alarm configuration profile in
the hdsl2ShdslEndpointAlarmConfProfileTable. The value of this the hdsl2ShdslEndpointAlarmConfProfileTable. The value of this
object is the index of the referenced profile in the object is the index of the referenced profile in the
hdsl2ShdslEndpointAlarmConfProfileTable. The alarm threshold hdsl2ShdslEndpointAlarmConfProfileTable. The alarm threshold
configuration in the referenced profile will be used by default configuration in the referenced profile will be used by default
for all segment endpoints in this span. Individual endpoints for all segment endpoints in this span. Individual endpoints
may override this profile by explicitly specifying some other may override this profile by explicitly specifying some other
profile in the hdsl2ShdslEndpointConfTable. By default, this profile in the hdsl2ShdslEndpointConfTable. By default, this
object will have the value 'DEFVAL' (the index of the default object will have the value 'DEFVAL' (the index of the default
profile)." profile).
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
::= { hdsl2ShdslSpanConfEntry 3 } ::= { hdsl2ShdslSpanConfEntry 3 }
-- Span Status Group -- Span Status Group
-- --
hdsl2ShdslSpanStatusTable OBJECT-TYPE hdsl2ShdslSpanStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanStatusEntry SYNTAX SEQUENCE OF Hdsl2ShdslSpanStatusEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table provides overall status information of "This table provides overall status information of
HDSL2/SHDSL spans." HDSL2/SHDSL spans. This table contains live data from
equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 2 } ::= { hdsl2ShdslMibObjects 2 }
hdsl2ShdslSpanStatusEntry OBJECT-TYPE hdsl2ShdslSpanStatusEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanStatusEntry SYNTAX Hdsl2ShdslSpanStatusEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2ShdslSpanStatusTable. Each entry "An entry in the hdsl2ShdslSpanStatusTable. Each entry
represents the complete span in a single HDSL2/SHDSL line. It represents the complete span in a single HDSL2/SHDSL line.
is indexed by the ifIndex of the associated HDSL2/SHDSL line." It is indexed by the ifIndex of the associated HDSL2/SHDSL
line."
INDEX { ifIndex } INDEX { ifIndex }
::= { hdsl2ShdslSpanStatusTable 1 } ::= { hdsl2ShdslSpanStatusTable 1 }
Hdsl2ShdslSpanStatusEntry ::= Hdsl2ShdslSpanStatusEntry ::=
SEQUENCE SEQUENCE
{ {
hdsl2ShdslStatusNumAvailRepeaters INTEGER, hdsl2ShdslStatusNumAvailRepeaters INTEGER,
hdsl2ShdslStatusMaxAttainableLineRate Integer32, hdsl2ShdslStatusMaxAttainableLineRate INTEGER,
hdsl2ShdslStatusActualLineRate Integer32, hdsl2ShdslStatusActualLineRate INTEGER,
hdsl2ShdslStatusTransmissionModeCurrent hdsl2ShdslStatusTransmissionModeCurrent
Hdsl2ShdslTransmissionModeType Hdsl2ShdslTransmissionModeType
} }
hdsl2ShdslStatusNumAvailRepeaters OBJECT-TYPE hdsl2ShdslStatusNumAvailRepeaters OBJECT-TYPE
SYNTAX INTEGER(0..8) SYNTAX INTEGER(0..8)
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Contains the actual number of repeaters/regenerators "Contains the actual number of repeaters/regenerators
discovered in this HDSL2/SHDSL span." discovered in this HDSL2/SHDSL span."
::= { hdsl2ShdslSpanStatusEntry 1 } ::= { hdsl2ShdslSpanStatusEntry 1 }
Expires October 2, 2001 Page [16]
hdsl2ShdslStatusMaxAttainableLineRate OBJECT-TYPE hdsl2ShdslStatusMaxAttainableLineRate OBJECT-TYPE
SYNTAX Integer32 SYNTAX INTEGER(0..4112000)
UNITS "bps" UNITS "bps"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Contains the maximum attainable line rate in this HDSL2/SHDSL "Contains the maximum attainable line rate in this HDSL2/SHDSL
span." span."
::= { hdsl2ShdslSpanStatusEntry 2 } ::= { hdsl2ShdslSpanStatusEntry 2 }
hdsl2ShdslStatusActualLineRate OBJECT-TYPE hdsl2ShdslStatusActualLineRate OBJECT-TYPE
SYNTAX Integer32 SYNTAX INTEGER(0..4112000)
UNITS "bps" UNITS "bps"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Contains the actual line rate in this HDSL2/SHDSL span." "Contains the actual line rate in this HDSL2/SHDSL span. This
should equal ifSpeed."
::= { hdsl2ShdslSpanStatusEntry 3 } ::= { hdsl2ShdslSpanStatusEntry 3 }
hdsl2ShdslStatusTransmissionModeCurrent OBJECT-TYPE hdsl2ShdslStatusTransmissionModeCurrent OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Contains the current PSD regional setting of the "Contains the current Power Spectral Density (PSD) regional
HDSL2/SHDSL span." setting of the HDSL2/SHDSL span."
::= { hdsl2ShdslSpanStatusEntry 4 } ::= { hdsl2ShdslSpanStatusEntry 4 }
-- Unit Inventory Group -- Unit Inventory Group
-- --
hdsl2ShdslInventoryTable OBJECT-TYPE hdsl2ShdslInventoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslInventoryEntry SYNTAX SEQUENCE OF Hdsl2ShdslInventoryEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table supports retrieval of unit inventory information "This table supports retrieval of unit inventory information
available via the EOC from units in a HDSL2/SHDSL line." available via the EOC from units in a HDSL2/SHDSL line.
Entries in this table are dynamically created during the
line discovery process. The life cycle for these entries
is as follows:
- xtu discovers a device, either a far-end xtu or an xru
- an inventory table entry is created for the device
- the line goes down for whatever reason
- inventory table entries for unreachable devices are
destroyed.
As these entries are created/destroyed dynamically, they
are NOT persistent."
::= { hdsl2ShdslMibObjects 3 } ::= { hdsl2ShdslMibObjects 3 }
hdsl2ShdslInventoryEntry OBJECT-TYPE hdsl2ShdslInventoryEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslInventoryEntry SYNTAX Hdsl2ShdslInventoryEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2ShdslInventoryTable. Each entry "An entry in the hdsl2ShdslInventoryTable. Each entry
represents inventory information for a single unit in a represents inventory information for a single unit in a
HDSL2/SHDSL line. It is indexed by the ifIndex of the HDSL2/SHDSL line. It is indexed by the ifIndex of the
HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the
associated unit." associated unit."
INDEX { ifIndex, hdsl2ShdslInvIndex } INDEX { ifIndex, hdsl2ShdslInvIndex }
::= { hdsl2ShdslInventoryTable 1 } ::= { hdsl2ShdslInventoryTable 1 }
Hdsl2ShdslInventoryEntry ::= Hdsl2ShdslInventoryEntry ::=
Expires October 2, 2001 Page [17]
SEQUENCE SEQUENCE
{ {
hdsl2ShdslInvIndex Hdsl2ShdslUnitId, hdsl2ShdslInvIndex Hdsl2ShdslUnitId,
hdsl2ShdslInvVendorID OCTET STRING, hdsl2ShdslInvVendorID OCTET STRING,
hdsl2ShdslInvVendorModelNumber OCTET STRING, hdsl2ShdslInvVendorModelNumber OCTET STRING,
hdsl2ShdslInvVendorSerialNumber OCTET STRING, hdsl2ShdslInvVendorSerialNumber OCTET STRING,
hdsl2ShdslInvVendorEOCSoftwareVersion Integer32, hdsl2ShdslInvVendorEOCSoftwareVersion Integer32,
hdsl2ShdslInvStandardVersion Integer32, hdsl2ShdslInvStandardVersion Integer32,
hdsl2ShdslInvVendorListNumber OCTET STRING, hdsl2ShdslInvVendorListNumber OCTET STRING,
hdsl2ShdslInvVendorIssueNumber OCTET STRING, hdsl2ShdslInvVendorIssueNumber OCTET STRING,
skipping to change at line 994 skipping to change at page 20, line 14
hdsl2ShdslInvVendorOther OCTET STRING, hdsl2ShdslInvVendorOther OCTET STRING,
hdsl2ShdslInvTransmissionModeCapability hdsl2ShdslInvTransmissionModeCapability
Hdsl2ShdslTransmissionModeType Hdsl2ShdslTransmissionModeType
} }
hdsl2ShdslInvIndex OBJECT-TYPE hdsl2ShdslInvIndex OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitId SYNTAX Hdsl2ShdslUnitId
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The index into the hdsl2ShdslInventoryTable." "Each entry in this table corresponds to a physical element
in a HDSL2/SHDSL Span. It is based on the EOC unit addressing
scheme with reference to the xtuC."
::= { hdsl2ShdslInventoryEntry 1 } ::= { hdsl2ShdslInventoryEntry 1 }
hdsl2ShdslInvVendorID OBJECT-TYPE hdsl2ShdslInvVendorID OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(8)) SYNTAX OCTET STRING(SIZE(8))
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Vendor ID as reported in an Inventory Response message." "Vendor ID as reported in an Inventory Response message."
::= { hdsl2ShdslInventoryEntry 2 } ::= { hdsl2ShdslInventoryEntry 2 }
skipping to change at line 1027 skipping to change at page 20, line 49
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Vendor serial number as reported in an Inventory Response "Vendor serial number as reported in an Inventory Response
message." message."
::= { hdsl2ShdslInventoryEntry 4 } ::= { hdsl2ShdslInventoryEntry 4 }
hdsl2ShdslInvVendorEOCSoftwareVersion OBJECT-TYPE hdsl2ShdslInvVendorEOCSoftwareVersion OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
Expires October 2, 2001 Page [18]
DESCRIPTION DESCRIPTION
"Vendor EOC version as reported in a Discovery Response "Vendor EOC version as reported in a Discovery Response
message." message."
::= { hdsl2ShdslInventoryEntry 5 } ::= { hdsl2ShdslInventoryEntry 5 }
hdsl2ShdslInvStandardVersion OBJECT-TYPE hdsl2ShdslInvStandardVersion OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
skipping to change at line 1066 skipping to change at page 21, line 33
DESCRIPTION DESCRIPTION
"Vendor issue number as reported in an Inventory Response "Vendor issue number as reported in an Inventory Response
message." message."
::= { hdsl2ShdslInventoryEntry 8 } ::= { hdsl2ShdslInventoryEntry 8 }
hdsl2ShdslInvVendorSoftwareVersion OBJECT-TYPE hdsl2ShdslInvVendorSoftwareVersion OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(6)) SYNTAX OCTET STRING(SIZE(6))
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Vendor software version as reported in an Inventory "Vendor software version as reported in an Inventory Response
Response message." message."
::= { hdsl2ShdslInventoryEntry 9 } ::= { hdsl2ShdslInventoryEntry 9 }
hdsl2ShdslInvEquipmentCode OBJECT-TYPE hdsl2ShdslInvEquipmentCode OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(10)) SYNTAX OCTET STRING(SIZE(10))
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Equipment code conforming to ANSI T1.213, Coded Identification "Equipment code conforming to ANSI T1.213, Coded Identification
of Equipment Entities." of Equipment Entities."
::= { hdsl2ShdslInventoryEntry 10 } ::= { hdsl2ShdslInventoryEntry 10 }
hdsl2ShdslInvVendorOther OBJECT-TYPE hdsl2ShdslInvVendorOther OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(12)) SYNTAX OCTET STRING(SIZE(12))
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Other vendor information as reported in an Inventory Response
Expires October 2, 2001 Page [19] message."
"Other vendor information as reported in an Inventory
Response message."
::= { hdsl2ShdslInventoryEntry 11 } ::= { hdsl2ShdslInventoryEntry 11 }
hdsl2ShdslInvTransmissionModeCapability OBJECT-TYPE hdsl2ShdslInvTransmissionModeCapability OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Contains the transmission mode capability of the SHDSL unit." "Contains the transmission mode capability of the SHDSL unit."
::= { hdsl2ShdslInventoryEntry 12 } ::= { hdsl2ShdslInventoryEntry 12 }
-- Segment Endpoint Configuration Group -- Segment Endpoint Configuration Group
-- --
hdsl2ShdslEndpointConfTable OBJECT-TYPE hdsl2ShdslEndpointConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointConfEntry SYNTAX SEQUENCE OF Hdsl2ShdslEndpointConfEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table supports configuration parameters for segment "This table supports configuration parameters for segment
endpoints in a HDSL2/SHDSL line." endpoints in a HDSL2/SHDSL line. As this table is indexed
by ifIndex, it MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 4 } ::= { hdsl2ShdslMibObjects 4 }
hdsl2ShdslEndpointConfEntry OBJECT-TYPE hdsl2ShdslEndpointConfEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointConfEntry SYNTAX Hdsl2ShdslEndpointConfEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2ShdslEndpointConfTable. Each entry "An entry in the hdsl2ShdslEndpointConfTable. Each entry
represents a single segment endpoint in a HDSL2/SHDSL line. represents a single segment endpoint in a HDSL2/SHDSL line.
It is indexed by the ifIndex of the HDSL2/SHDSL line, the It is indexed by the ifIndex of the HDSL2/SHDSL line, the
skipping to change at line 1142 skipping to change at page 22, line 55
hdsl2ShdslEndpointSide OBJECT-TYPE hdsl2ShdslEndpointSide OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitSide SYNTAX Hdsl2ShdslUnitSide
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The side of the unit associated with this segment endpoint - "The side of the unit associated with this segment endpoint -
Network/Customer side - as per the Hdsl2ShdslUnitSide textual Network/Customer side - as per the Hdsl2ShdslUnitSide textual
convention." convention."
::= { hdsl2ShdslEndpointConfEntry 1 } ::= { hdsl2ShdslEndpointConfEntry 1 }
Expires October 2, 2001 Page [20]
hdsl2ShdslEndpointWirePair OBJECT-TYPE hdsl2ShdslEndpointWirePair OBJECT-TYPE
SYNTAX Hdsl2ShdslWirePair SYNTAX Hdsl2ShdslWirePair
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The wire-pair of the modem associated with this segment "The wire-pair of the modem associated with this segment
endpoint as per the Hdsl2ShdslWirePair textual convention." endpoint as per the Hdsl2ShdslWirePair textual convention."
::= { hdsl2ShdslEndpointConfEntry 2 } ::= { hdsl2ShdslEndpointConfEntry 2 }
hdsl2ShdslEndpointAlarmConfProfile OBJECT-TYPE hdsl2ShdslEndpointAlarmConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32)) SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-write MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the alarm threshold values to be used "This object configures the alarm threshold values to be used
for this segment endpoint. The values are obtained from the for this segment endpoint. The values are obtained from the
alarm configuration profile referenced by this object. The alarm configuration profile referenced by this object. The
value of this object is the index of the referenced profile in value of this object is the index of the referenced profile in
the hdsl2ShdslEndpointAlarmConf ProfileTable, or NULL (a zero- the hdsl2ShdslEndpointAlarmConf ProfileTable, or NULL (a zero-
length SnmpAdminString). If the value is NULL, the endpoint length SnmpAdminString). If the value is a zero-length
uses the default Alarm Configuration Profile for the associated SnmpAdminString, the endpoint uses the default Alarm
span as per the hdsl2ShdslSpanConfAlarmProfile object in the Configuration Profile for the associated span as per the
hdsl2ShdslSpanConfAlarmProfile object in the
hdsl2ShdslSpanConfTable. The default value of this object is hdsl2ShdslSpanConfTable. The default value of this object is
NULL." a zero-length SnmpAdminString.
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
::= { hdsl2ShdslEndpointConfEntry 3 } ::= { hdsl2ShdslEndpointConfEntry 3 }
-- Segment Endpoint Current Status/Performance Group -- Segment Endpoint Current Status/Performance Group
-- --
hdsl2ShdslEndpointCurrTable OBJECT-TYPE hdsl2ShdslEndpointCurrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointCurrEntry SYNTAX SEQUENCE OF Hdsl2ShdslEndpointCurrEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table contains current status and performance information "This table contains current status and performance information
for segment endpoints in HDSL2/SHDSL Lines." for segment endpoints in HDSL2/SHDSL Lines. As with other
tables in this MIB indexed by ifIndex, entries in this table
MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 5 } ::= { hdsl2ShdslMibObjects 5 }
hdsl2ShdslEndpointCurrEntry OBJECT-TYPE hdsl2ShdslEndpointCurrEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointCurrEntry SYNTAX Hdsl2ShdslEndpointCurrEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2ShdslEndpointCurrTable. Each entry "An entry in the hdsl2ShdslEndpointCurrTable. Each entry
contains status and performance information relating to a contains status and performance information relating to a
single segment endpoint. It is indexed by the ifIndex of the single segment endpoint. It is indexed by the ifIndex of the
HDSL2/SHDSL line, the UnitId of the associated unit, the side HDSL2/SHDSL line, the UnitId of the associated unit, the side
of the unit, and the wire-pair of the associated modem." of the unit, and the wire-pair of the associated modem."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair } hdsl2ShdslEndpointWirePair }
::= { hdsl2ShdslEndpointCurrTable 1 } ::= { hdsl2ShdslEndpointCurrTable 1 }
Hdsl2ShdslEndpointCurrEntry ::= Hdsl2ShdslEndpointCurrEntry ::=
SEQUENCE SEQUENCE
Expires October 2, 2001 Page [21]
{ {
hdsl2ShdslEndpointCurrAtn Integer32, hdsl2ShdslEndpointCurrAtn INTEGER,
hdsl2ShdslEndpointCurrSnrMgn Integer32, hdsl2ShdslEndpointCurrSnrMgn INTEGER,
hdsl2ShdslEndpointCurrStatus Integer32, hdsl2ShdslEndpointCurrStatus BITS,
hdsl2ShdslEndpointES Counter32, hdsl2ShdslEndpointES Counter32,
hdsl2ShdslEndpointSES Counter32, hdsl2ShdslEndpointSES Counter32,
hdsl2ShdslEndpointCRCanomalies Counter32, hdsl2ShdslEndpointCRCanomalies Counter32,
hdsl2ShdslEndpointLOSWS Counter32, hdsl2ShdslEndpointLOSWS Counter32,
hdsl2ShdslEndpointUAS Counter32, hdsl2ShdslEndpointUAS Counter32,
hdsl2ShdslEndpointCurr15MinTimeElapsed Hdsl2ShdslPerfTimeElapsed, hdsl2ShdslEndpointCurr15MinTimeElapsed
Hdsl2ShdslPerfTimeElapsed,
hdsl2ShdslEndpointCurr15MinES PerfCurrentCount, hdsl2ShdslEndpointCurr15MinES PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinSES PerfCurrentCount, hdsl2ShdslEndpointCurr15MinSES PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinCRCanomalies PerfCurrentCount, hdsl2ShdslEndpointCurr15MinCRCanomalies PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinLOSWS PerfCurrentCount, hdsl2ShdslEndpointCurr15MinLOSWS PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinUAS PerfCurrentCount, hdsl2ShdslEndpointCurr15MinUAS PerfCurrentCount,
hdsl2ShdslEndpointCurr1DayTimeElapsed Hdsl2ShdslPerfTimeElapsed, hdsl2ShdslEndpointCurr1DayTimeElapsed
hdsl2ShdslEndpointCurr1DayES Hdsl2ShdslPerfCurrDayCount, Hdsl2ShdslPerfTimeElapsed,
hdsl2ShdslEndpointCurr1DaySES Hdsl2ShdslPerfCurrDayCount, hdsl2ShdslEndpointCurr1DayES
hdsl2ShdslEndpointCurr1DayCRCanomalies Hdsl2ShdslPerfCurrDayCount, Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DayLOSWS Hdsl2ShdslPerfCurrDayCount, hdsl2ShdslEndpointCurr1DaySES
hdsl2ShdslEndpointCurr1DayUAS Hdsl2ShdslPerfCurrDayCount Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DayCRCanomalies
Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DayLOSWS
Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DayUAS
Hdsl2ShdslPerfCurrDayCount
} }
hdsl2ShdslEndpointCurrAtn OBJECT-TYPE hdsl2ShdslEndpointCurrAtn OBJECT-TYPE
SYNTAX Integer32 SYNTAX INTEGER(-127..128)
UNITS "dB" UNITS "dB"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The current loop attenuation for this endpoint as reported in "The current loop attenuation for this endpoint as reported in
a Network or Customer Side Performance Status message." a Network or Customer Side Performance Status message."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 1 } ::= { hdsl2ShdslEndpointCurrEntry 1 }
hdsl2ShdslEndpointCurrSnrMgn OBJECT-TYPE hdsl2ShdslEndpointCurrSnrMgn OBJECT-TYPE
SYNTAX Integer32 SYNTAX INTEGER(-127..128)
UNITS "dB" UNITS "dB"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The current SNR margin for this endpoint as reported in a "The current SNR margin for this endpoint as reported in a
Status Response/SNR message." Status Response/SNR message."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 2 } ::= { hdsl2ShdslEndpointCurrEntry 2 }
hdsl2ShdslEndpointCurrStatus OBJECT-TYPE hdsl2ShdslEndpointCurrStatus OBJECT-TYPE
SYNTAX Integer32 SYNTAX BITS
{
noDefect(0),
powerBackoff(1),
deviceFault(2),
dcContinuityFault(3),
snrMarginAlarm(4),
loopAttenuationAlarm(5),
loswFailureAlarm(6),
configInitFailure(7),
protocolInitFailure(8),
noNeighborPresent(9),
loopbackActive(10)
}
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Contains the current state of the endpoint. This is a "Contains the current state of the endpoint. This is a
bit-map of possible conditions. The various bit positions bitmap of possible conditions. The various bit positions
are: are:
1 noDefect There no defects on the line noDefect There no defects on the line.
2 powerBackoff Indicates enhanced Power Backoff powerBackoff Indicates enhanced Power Backoff.
Expires October 2, 2001 Page [22] deviceFault Indicates a vendor-dependent
4 deviceFault Indicates a vendor-dependent diagnostic or self-test fault
detection of diagnostics or has been detected.
self-test results
8 dcContinuityFault Indicates vendor-dependent dcContinuityFault Indicates vendor-dependent
conditions that interfere with conditions that interfere with
span powering such as short and span powering such as short and
open circuits open circuits.
16 snrMarginAlarm Indicates that the SNR margin snrMarginAlarm Indicates that the SNR margin
has dropped below the alarm threshold has dropped below the alarm threshold.
32 loopAttenuationAlarm Indicates that the loop attentuation loopAttenuationAlarm Indicates that the loop attenuation
has dropped below the alarm threshold has dropped below the alarm threshold.
64 loswFailureAlarm Indicates a forward LOSW alarm loswFailureAlarm Indicates a forward LOSW alarm.
128 configInitFailure Endpoint failure during initialization configInitFailure Endpoint failure during initialization
due to paired endpoint not able to due to paired endpoint not able to
support requested configuration support requested configuration.
256 protocolInitFailure Endpoint failure during initialization protocolInitFailure Endpoint failure during initialization
due to incompatible protocol used by due to incompatible protocol used by
the paired endpoint. the paired endpoint.
512 noNeighborPresent Endpoint failure during initialization noNeighborPresent Endpoint failure during initialization
due to no activation sequence detected due to no activation sequence detected
from paired endpoint. from paired endpoint.
1024 loopbackActive A loopback is currently active at this loopbackActive A loopback is currently active at this
Segment Endpoint. Segment Endpoint.
This is intended to supplement ifOperStatus." This is intended to supplement ifOperStatus. Note that there
is a 1-1 relationship between the status bits defined in this
object and the notification thresholds defined elsewhere in
this MIB."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 3 } ::= { hdsl2ShdslEndpointCurrEntry 3 }
hdsl2ShdslEndpointES OBJECT-TYPE hdsl2ShdslEndpointES OBJECT-TYPE
SYNTAX Counter32 SYNTAX Counter32
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Errored Seconds (ES) on this endpoint since the xU "Count of Errored Seconds (ES) on this endpoint since the xU
was last restarted." was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 4 } ::= { hdsl2ShdslEndpointCurrEntry 4 }
hdsl2ShdslEndpointSES OBJECT-TYPE hdsl2ShdslEndpointSES OBJECT-TYPE
SYNTAX Counter32 SYNTAX Counter32
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Severely Errored Seconds (SES) on this endpoint "Count of Severely Errored Seconds (SES) on this endpoint
since the xU was last restarted." since the xU was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 5 } ::= { hdsl2ShdslEndpointCurrEntry 5 }
Expires October 2, 2001 Page [23]
hdsl2ShdslEndpointCRCanomalies OBJECT-TYPE hdsl2ShdslEndpointCRCanomalies OBJECT-TYPE
SYNTAX Counter32 SYNTAX Counter32
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of CRC anomalies on this endpoint since the xU was "Count of CRC anomalies on this endpoint since the xU was
last restarted." last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 6 } ::= { hdsl2ShdslEndpointCurrEntry 6 }
hdsl2ShdslEndpointLOSWS OBJECT-TYPE hdsl2ShdslEndpointLOSWS OBJECT-TYPE
SYNTAX Counter32 SYNTAX Counter32
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds on this endpoint "Count of Loss of Sync Word (LOSW) Seconds on this endpoint
since the xU was last restarted." since the xU was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 7 } ::= { hdsl2ShdslEndpointCurrEntry 7 }
hdsl2ShdslEndpointUAS OBJECT-TYPE hdsl2ShdslEndpointUAS OBJECT-TYPE
SYNTAX Counter32 SYNTAX Counter32
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Unavailable Seconds (UAS) on this endpoint since "Count of Unavailable Seconds (UAS) on this endpoint since
the xU was last restarted." the xU was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 8 } ::= { hdsl2ShdslEndpointCurrEntry 8 }
hdsl2ShdslEndpointCurr15MinTimeElapsed OBJECT-TYPE hdsl2ShdslEndpointCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Total elapsed seconds in the current 15-minute interval." "Total elapsed seconds in the current 15-minute interval."
::= { hdsl2ShdslEndpointCurrEntry 9 } ::= { hdsl2ShdslEndpointCurrEntry 9 }
hdsl2ShdslEndpointCurr15MinES OBJECT-TYPE hdsl2ShdslEndpointCurr15MinES OBJECT-TYPE
SYNTAX PerfCurrentCount SYNTAX PerfCurrentCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Errored Seconds (ES) in the current 15-minute "Count of Errored Seconds (ES) in the current 15-minute
interval." interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 10 } ::= { hdsl2ShdslEndpointCurrEntry 10 }
hdsl2ShdslEndpointCurr15MinSES OBJECT-TYPE hdsl2ShdslEndpointCurr15MinSES OBJECT-TYPE
SYNTAX PerfCurrentCount SYNTAX PerfCurrentCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
Expires October 2, 2001 Page [24]
"Count of Severely Errored Seconds (SES) in the current "Count of Severely Errored Seconds (SES) in the current
15-minute interval." 15-minute interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 11 } ::= { hdsl2ShdslEndpointCurrEntry 11 }
hdsl2ShdslEndpointCurr15MinCRCanomalies OBJECT-TYPE hdsl2ShdslEndpointCurr15MinCRCanomalies OBJECT-TYPE
SYNTAX PerfCurrentCount SYNTAX PerfCurrentCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of CRC anomalies in the current 15-minute interval." "Count of CRC anomalies in the current 15-minute interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 12 } ::= { hdsl2ShdslEndpointCurrEntry 12 }
hdsl2ShdslEndpointCurr15MinLOSWS OBJECT-TYPE hdsl2ShdslEndpointCurr15MinLOSWS OBJECT-TYPE
SYNTAX PerfCurrentCount SYNTAX PerfCurrentCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds in the current "Count of Loss of Sync Word (LOSW) Seconds in the current
15-minute interval." 15-minute interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 13 } ::= { hdsl2ShdslEndpointCurrEntry 13 }
hdsl2ShdslEndpointCurr15MinUAS OBJECT-TYPE hdsl2ShdslEndpointCurr15MinUAS OBJECT-TYPE
SYNTAX PerfCurrentCount SYNTAX PerfCurrentCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Unavailable Seconds (UAS) in the current 15-minute "Count of Unavailable Seconds (UAS) in the current 15-minute
interval." interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 14 } ::= { hdsl2ShdslEndpointCurrEntry 14 }
hdsl2ShdslEndpointCurr1DayTimeElapsed OBJECT-TYPE hdsl2ShdslEndpointCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Number of seconds that have elapsed since the beginning of "Number of seconds that have elapsed since the beginning of
the current 1-day interval." the current 1-day interval."
::= { hdsl2ShdslEndpointCurrEntry 15 } ::= { hdsl2ShdslEndpointCurrEntry 15 }
hdsl2ShdslEndpointCurr1DayES OBJECT-TYPE hdsl2ShdslEndpointCurr1DayES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Errored Seconds (ES) during the current day as "Count of Errored Seconds (ES) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed." measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 16 } ::= { hdsl2ShdslEndpointCurrEntry 16 }
hdsl2ShdslEndpointCurr1DaySES OBJECT-TYPE hdsl2ShdslEndpointCurr1DaySES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds" UNITS "seconds"
Expires October 2, 2001 Page [25]
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Severely Errored Seconds (SES) during the current "Count of Severely Errored Seconds (SES) during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed." day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 17 } ::= { hdsl2ShdslEndpointCurrEntry 17 }
hdsl2ShdslEndpointCurr1DayCRCanomalies OBJECT-TYPE hdsl2ShdslEndpointCurr1DayCRCanomalies OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of CRC anomalies during the current day as measured "Count of CRC anomalies during the current day as measured
by hdsl2ShdslEndpointCurr1DayTimeElapsed." by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 18 } ::= { hdsl2ShdslEndpointCurrEntry 18 }
hdsl2ShdslEndpointCurr1DayLOSWS OBJECT-TYPE hdsl2ShdslEndpointCurr1DayLOSWS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the current "Count of Loss of Sync Word (LOSW) Seconds during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed." day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 19 } ::= { hdsl2ShdslEndpointCurrEntry 19 }
hdsl2ShdslEndpointCurr1DayUAS OBJECT-TYPE hdsl2ShdslEndpointCurr1DayUAS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Unavailable Seconds (UAS) during the current day as "Count of Unavailable Seconds (UAS) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed." measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 20 } ::= { hdsl2ShdslEndpointCurrEntry 20 }
-- Segment Endpoint 15-Minute Interval Status/Performance Group -- Segment Endpoint 15-Minute Interval Status/Performance Group
-- --
hdsl2Shdsl15MinIntervalTable OBJECT-TYPE hdsl2Shdsl15MinIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2Shdsl15MinIntervalEntry SYNTAX SEQUENCE OF Hdsl2Shdsl15MinIntervalEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table provides one row for each HDSL2/SHDSL endpoint "This table provides one row for each HDSL2/SHDSL endpoint
performance data collection interval." performance data collection interval. This table contains
live data from equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 6 } ::= { hdsl2ShdslMibObjects 6 }
hdsl2Shdsl15MinIntervalEntry OBJECT-TYPE hdsl2Shdsl15MinIntervalEntry OBJECT-TYPE
SYNTAX Hdsl2Shdsl15MinIntervalEntry SYNTAX Hdsl2Shdsl15MinIntervalEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2Shdsl15MinIntervalTable." "An entry in the hdsl2Shdsl15MinIntervalTable."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
Expires October 2, 2001 Page [26]
hdsl2ShdslEndpointWirePair, hdsl2Shdsl15MinIntervalNumber} hdsl2ShdslEndpointWirePair, hdsl2Shdsl15MinIntervalNumber}
::= { hdsl2Shdsl15MinIntervalTable 1 } ::= { hdsl2Shdsl15MinIntervalTable 1 }
Hdsl2Shdsl15MinIntervalEntry ::= Hdsl2Shdsl15MinIntervalEntry ::=
SEQUENCE SEQUENCE
{ {
hdsl2Shdsl15MinIntervalNumber INTEGER, hdsl2Shdsl15MinIntervalNumber INTEGER,
hdsl2Shdsl15MinIntervalES PerfIntervalCount, hdsl2Shdsl15MinIntervalES PerfIntervalCount,
hdsl2Shdsl15MinIntervalSES PerfIntervalCount, hdsl2Shdsl15MinIntervalSES PerfIntervalCount,
hdsl2Shdsl15MinIntervalCRCanomalies PerfIntervalCount, hdsl2Shdsl15MinIntervalCRCanomalies PerfIntervalCount,
skipping to change at line 1515 skipping to change at page 30, line 42
2..96 are optional." 2..96 are optional."
::= { hdsl2Shdsl15MinIntervalEntry 1 } ::= { hdsl2Shdsl15MinIntervalEntry 1 }
hdsl2Shdsl15MinIntervalES OBJECT-TYPE hdsl2Shdsl15MinIntervalES OBJECT-TYPE
SYNTAX PerfIntervalCount SYNTAX PerfIntervalCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Errored Seconds (ES) during the interval." "Count of Errored Seconds (ES) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 2 } ::= { hdsl2Shdsl15MinIntervalEntry 2 }
hdsl2Shdsl15MinIntervalSES OBJECT-TYPE hdsl2Shdsl15MinIntervalSES OBJECT-TYPE
SYNTAX PerfIntervalCount SYNTAX PerfIntervalCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Severely Errored Seconds (SES) during the "Count of Severely Errored Seconds (SES) during the interval."
interval." REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 3 } ::= { hdsl2Shdsl15MinIntervalEntry 3 }
hdsl2Shdsl15MinIntervalCRCanomalies OBJECT-TYPE hdsl2Shdsl15MinIntervalCRCanomalies OBJECT-TYPE
SYNTAX PerfIntervalCount SYNTAX PerfIntervalCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of CRC anomalies during the interval." "Count of CRC anomalies during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 4 } ::= { hdsl2Shdsl15MinIntervalEntry 4 }
hdsl2Shdsl15MinIntervalLOSWS OBJECT-TYPE hdsl2Shdsl15MinIntervalLOSWS OBJECT-TYPE
SYNTAX PerfIntervalCount SYNTAX PerfIntervalCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
Expires October 2, 2001 Page [27]
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the "Count of Loss of Sync Word (LOSW) Seconds during the
interval." interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 5 } ::= { hdsl2Shdsl15MinIntervalEntry 5 }
hdsl2Shdsl15MinIntervalUAS OBJECT-TYPE hdsl2Shdsl15MinIntervalUAS OBJECT-TYPE
SYNTAX PerfIntervalCount SYNTAX PerfIntervalCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Unavailable Seconds (UAS) during the interval." "Count of Unavailable Seconds (UAS) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 6 } ::= { hdsl2Shdsl15MinIntervalEntry 6 }
-- Segment Endpoint 1-Day Interval Status/Performance Group -- Segment Endpoint 1-Day Interval Status/Performance Group
-- --
hdsl2Shdsl1DayIntervalTable OBJECT-TYPE hdsl2Shdsl1DayIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2Shdsl1DayIntervalEntry SYNTAX SEQUENCE OF Hdsl2Shdsl1DayIntervalEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table provides one row for each HDSL2/SHDSL endpoint "This table provides one row for each HDSL2/SHDSL endpoint
performance data collection interval." performance data collection interval. This table contains
live data from equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 7 } ::= { hdsl2ShdslMibObjects 7 }
hdsl2Shdsl1DayIntervalEntry OBJECT-TYPE hdsl2Shdsl1DayIntervalEntry OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalEntry SYNTAX Hdsl2Shdsl1DayIntervalEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2Shdsl1DayIntervalTable." "An entry in the hdsl2Shdsl1DayIntervalTable."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2Shdsl1DayIntervalNumber } hdsl2ShdslEndpointWirePair, hdsl2Shdsl1DayIntervalNumber }
skipping to change at line 1596 skipping to change at page 32, line 22
hdsl2Shdsl1DayIntervalLOSWS Hdsl2Shdsl1DayIntervalCount, hdsl2Shdsl1DayIntervalLOSWS Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalUAS Hdsl2Shdsl1DayIntervalCount hdsl2Shdsl1DayIntervalUAS Hdsl2Shdsl1DayIntervalCount
} }
hdsl2Shdsl1DayIntervalNumber OBJECT-TYPE hdsl2Shdsl1DayIntervalNumber OBJECT-TYPE
SYNTAX INTEGER(1..30) SYNTAX INTEGER(1..30)
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"History Data Interval number. Interval 1 is the the most "History Data Interval number. Interval 1 is the the most
Expires October 2, 2001 Page [28]
recent previous day; interval 30 is 30 days ago. Intervals recent previous day; interval 30 is 30 days ago. Intervals
2..30 are optional." 2..30 are optional."
::= { hdsl2Shdsl1DayIntervalEntry 1 } ::= { hdsl2Shdsl1DayIntervalEntry 1 }
hdsl2Shdsl1DayIntervalMoniSecs OBJECT-TYPE hdsl2Shdsl1DayIntervalMoniSecs OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The amount of time in the 1-day interval over which the "The amount of time in the 1-day interval over which the
performance monitoring information is actually counted. performance monitoring information is actually counted.
This value will be the same as the interval duration except This value will be the same as the interval duration except
in a situation where performance monitoring data could not in a situation where performance monitoring data could not
be collected for any reason." be collected for any reason."
::= { hdsl2Shdsl1DayIntervalEntry 2 } ::= { hdsl2Shdsl1DayIntervalEntry 2 }
hdsl2Shdsl1DayIntervalES OBJECT-TYPE hdsl2Shdsl1DayIntervalES OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Errored Seconds (ES) during the 1-day interval as "Count of Errored Seconds (ES) during the 1-day interval as
measured by hdsl2Shdsl1DayIntervalMoniSecs." measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 3 } ::= { hdsl2Shdsl1DayIntervalEntry 3 }
hdsl2Shdsl1DayIntervalSES OBJECT-TYPE hdsl2Shdsl1DayIntervalSES OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Severely Errored Seconds (SES) during the 1-day "Count of Severely Errored Seconds (SES) during the 1-day
interval as measured by hdsl2Shdsl1DayIntervalMoniSecs." interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 4 } ::= { hdsl2Shdsl1DayIntervalEntry 4 }
hdsl2Shdsl1DayIntervalCRCanomalies OBJECT-TYPE hdsl2Shdsl1DayIntervalCRCanomalies OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of CRC anomalies during the 1-day interval as "Count of CRC anomalies during the 1-day interval as
measured by hdsl2Shdsl1DayIntervalMoniSecs." measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 5 } ::= { hdsl2Shdsl1DayIntervalEntry 5 }
hdsl2Shdsl1DayIntervalLOSWS OBJECT-TYPE hdsl2Shdsl1DayIntervalLOSWS OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the 1-day "Count of Loss of Sync Word (LOSW) Seconds during the 1-day
interval as measured by hdsl2Shdsl1DayIntervalMoniSecs." interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 6 } ::= { hdsl2Shdsl1DayIntervalEntry 6 }
Expires October 2, 2001 Page [29]
hdsl2Shdsl1DayIntervalUAS OBJECT-TYPE hdsl2Shdsl1DayIntervalUAS OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Unavailable Seconds (UAS) during the 1-day interval "Count of Unavailable Seconds (UAS) during the 1-day interval
as measured by hdsl2Shdsl1DayIntervalMoniSecs." as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 7 } ::= { hdsl2Shdsl1DayIntervalEntry 7 }
-- Maintenance Group -- Maintenance Group
-- --
hdsl2ShdslEndpointMaintTable OBJECT-TYPE hdsl2ShdslEndpointMaintTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointMaintEntry SYNTAX SEQUENCE OF Hdsl2ShdslEndpointMaintEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table supports maintenance operations (eg. loopbacks) "This table supports maintenance operations (eg. loopbacks)
to be performed on HDSL2/SHDSL segment endpoints." to be performed on HDSL2/SHDSL segment endpoints. This table
contains live data from equipment. As such, it is NOT
persistent."
::= { hdsl2ShdslMibObjects 8 } ::= { hdsl2ShdslMibObjects 8 }
hdsl2ShdslEndpointMaintEntry OBJECT-TYPE hdsl2ShdslEndpointMaintEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointMaintEntry SYNTAX Hdsl2ShdslEndpointMaintEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2ShdslEndpointMaintTable. Each entry "An entry in the hdsl2ShdslEndpointMaintTable. Each entry
corresponds to a single segment endpoint, and is indexed by the corresponds to a single segment endpoint, and is indexed by the
ifIndex of the HDSL2/SHDSL line, the UnitId of the associated ifIndex of the HDSL2/SHDSL line, the UnitId of the associated
skipping to change at line 1710 skipping to change at page 34, line 36
noLoopback(1), noLoopback(1),
normalLoopback(2), normalLoopback(2),
specialLoopback(3) specialLoopback(3)
} }
MAX-ACCESS read-write MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object controls configuration of loopbacks for the "This object controls configuration of loopbacks for the
associated segment endpoint. The status of the loopback associated segment endpoint. The status of the loopback
is obtained via the hdsl2ShdslEndpointCurrStatus object." is obtained via the hdsl2ShdslEndpointCurrStatus object."
Expires October 2, 2001 Page [30]
::= { hdsl2ShdslEndpointMaintEntry 1 } ::= { hdsl2ShdslEndpointMaintEntry 1 }
hdsl2ShdslMaintTipRingReversal OBJECT-TYPE hdsl2ShdslMaintTipRingReversal OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
normal(1), normal(1),
reversed(2) reversed(2)
} }
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object indicates the state of the tip/ring pair at "This object indicates the state of the tip/ring pair at the
the associated segment endpoint." associated segment endpoint."
::= { hdsl2ShdslEndpointMaintEntry 2 } ::= { hdsl2ShdslEndpointMaintEntry 2 }
hdsl2ShdslMaintPowerBackOff OBJECT-TYPE hdsl2ShdslMaintPowerBackOff OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
default(1), default(1),
enhanced(2) enhanced(2)
} }
MAX-ACCESS read-write MAX-ACCESS read-write
STATUS current STATUS current
skipping to change at line 1752 skipping to change at page 35, line 23
SYNTAX INTEGER SYNTAX INTEGER
{ {
ready(1), ready(1),
restart(2) restart(2)
} }
MAX-ACCESS read-write MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object enables the manager to trigger a soft restart "This object enables the manager to trigger a soft restart
of the modem at the associated segment endpoint. The manager of the modem at the associated segment endpoint. The manager
may only set this object to the 'restart(2)' value to initiate may only set this object to the 'restart(2)' value, which
a restart. The agent will perform a restart after initiates a restart. The agent will perform a restart after
approximately 5 seconds, and restore the object to the approximately 5 seconds. Following the 5 second period, the
'ready(1)' state." agent will restore the object to the 'ready(1)' state."
::= { hdsl2ShdslEndpointMaintEntry 4 } ::= { hdsl2ShdslEndpointMaintEntry 4 }
hdsl2ShdslUnitMaintTable OBJECT-TYPE hdsl2ShdslUnitMaintTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslUnitMaintEntry SYNTAX SEQUENCE OF Hdsl2ShdslUnitMaintEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table supports maintenance operations for units in a "This table supports maintenance operations for units in a
HDSL2/SHDSL line." HDSL2/SHDSL line. Entries in this table MUST be maintained
in a persistent manner."
::= { hdsl2ShdslMibObjects 9 } ::= { hdsl2ShdslMibObjects 9 }
Expires October 2, 2001 Page [31]
hdsl2ShdslUnitMaintEntry OBJECT-TYPE hdsl2ShdslUnitMaintEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitMaintEntry SYNTAX Hdsl2ShdslUnitMaintEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the hdsl2ShdslUnitMaintTable. Each entry "An entry in the hdsl2ShdslUnitMaintTable. Each entry
corresponds to a single unit, and is indexed by the ifIndex corresponds to a single unit, and is indexed by the ifIndex
of the HDSL2/SHDSL line and the UnitId of the associated of the HDSL2/SHDSL line and the UnitId of the associated
unit." unit."
INDEX { ifIndex, hdsl2ShdslInvIndex } INDEX { ifIndex, hdsl2ShdslInvIndex }
skipping to change at line 1787 skipping to change at page 36, line 4
unit." unit."
INDEX { ifIndex, hdsl2ShdslInvIndex } INDEX { ifIndex, hdsl2ShdslInvIndex }
::= { hdsl2ShdslUnitMaintTable 1 } ::= { hdsl2ShdslUnitMaintTable 1 }
Hdsl2ShdslUnitMaintEntry ::= Hdsl2ShdslUnitMaintEntry ::=
SEQUENCE SEQUENCE
{ {
hdsl2ShdslMaintLoopbackTimeout Integer32, hdsl2ShdslMaintLoopbackTimeout Integer32,
hdsl2ShdslMaintUnitPowerSource INTEGER hdsl2ShdslMaintUnitPowerSource INTEGER
} }
hdsl2ShdslMaintLoopbackTimeout OBJECT-TYPE hdsl2ShdslMaintLoopbackTimeout OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32(0..4095)
UNITS "minutes"
MAX-ACCESS read-write MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the timeout value for loopbacks "This object configures the timeout value for loopbacks
initiated at segments endpoints contained in the associated initiated at segments endpoints contained in the associated
unit. A value of 0 disables the timeout." unit. A value of 0 disables the timeout."
::= { hdsl2ShdslUnitMaintEntry 1 } ::= { hdsl2ShdslUnitMaintEntry 1 }
hdsl2ShdslMaintUnitPowerSource OBJECT-TYPE hdsl2ShdslMaintUnitPowerSource OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
skipping to change at line 1821 skipping to change at page 36, line 38
-- Span Configuration Profile Group -- Span Configuration Profile Group
-- --
hdsl2ShdslSpanConfProfileTable OBJECT-TYPE hdsl2ShdslSpanConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfProfileEntry SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfProfileEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table supports definitions of span configuration "This table supports definitions of span configuration
profiles for SHDSL lines. HDSL2 does not support these profiles for SHDSL lines. HDSL2 does not support these
configuration options." configuration options. This table MUST be maintained
in a persistent manner."
::= { hdsl2ShdslMibObjects 10 } ::= { hdsl2ShdslMibObjects 10 }
Expires October 2, 2001 Page [32]
hdsl2ShdslSpanConfProfileEntry OBJECT-TYPE hdsl2ShdslSpanConfProfileEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanConfProfileEntry SYNTAX Hdsl2ShdslSpanConfProfileEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Each entry corresponds to a single span configuration "Each entry corresponds to a single span configuration
profile. Each profile contains a set of span configuration profile. Each profile contains a set of span configuration
parameters. The configuration parameters in a profile are parameters. The configuration parameters in a profile are
applied to those lines referencing that profile (see the applied to those lines referencing that profile (see the
hdsl2ShdslSpanConfProfile object). Profiles may be hdsl2ShdslSpanConfProfile object). Profiles may be
created/deleted using the row creation/deletion mechanism created/deleted using the row creation/deletion mechanism
via hdsl2ShdslSpanConfProfileRowStatus. Profiles that are via hdsl2ShdslSpanConfProfileRowStatus. If an active
being referenced may not be deleted." entry is referenced in hdsl2ShdslSpanConfProfile, the
entry MUST remain active until all references are removed."
INDEX { IMPLIED hdsl2ShdslSpanConfProfileName } INDEX { IMPLIED hdsl2ShdslSpanConfProfileName }
::= { hdsl2ShdslSpanConfProfileTable 1 } ::= { hdsl2ShdslSpanConfProfileTable 1 }
Hdsl2ShdslSpanConfProfileEntry ::= Hdsl2ShdslSpanConfProfileEntry ::=
SEQUENCE SEQUENCE
{ {
hdsl2ShdslSpanConfProfileName SnmpAdminString, hdsl2ShdslSpanConfProfileName SnmpAdminString,
hdsl2ShdslSpanConfWireInterface INTEGER, hdsl2ShdslSpanConfWireInterface INTEGER,
hdsl2ShdslSpanConfMinLineRate Integer32, hdsl2ShdslSpanConfMinLineRate INTEGER,
hdsl2ShdslSpanConfMaxLineRate Integer32, hdsl2ShdslSpanConfMaxLineRate INTEGER,
hdsl2ShdslSpanConfPSD INTEGER, hdsl2ShdslSpanConfPSD INTEGER,
hdsl2ShdslSpanConfTransmissionMode hdsl2ShdslSpanConfTransmissionMode
Hdsl2ShdslTransmissionModeType, Hdsl2ShdslTransmissionModeType,
hdsl2ShdslSpanConfRemoteEnabled INTEGER, hdsl2ShdslSpanConfRemoteEnabled INTEGER,
hdsl2ShdslSpanConfPowerFeeding INTEGER, hdsl2ShdslSpanConfPowerFeeding INTEGER,
hdsl2ShdslSpanConfCurrCondTargetMarginDown INTEGER, hdsl2ShdslSpanConfCurrCondTargetMarginDown INTEGER,
hdsl2ShdslSpanConfWorstCaseTargetMarginDown INTEGER, hdsl2ShdslSpanConfWorstCaseTargetMarginDown INTEGER,
hdsl2ShdslSpanConfCurrCondTargetMarginUp INTEGER, hdsl2ShdslSpanConfCurrCondTargetMarginUp INTEGER,
hdsl2ShdslSpanConfWorstCaseTargetMarginUp INTEGER, hdsl2ShdslSpanConfWorstCaseTargetMarginUp INTEGER,
hdsl2ShdslSpanConfUsedTargetMargins Integer32, hdsl2ShdslSpanConfUsedTargetMargins BITS,
hdsl2ShdslSpanConfProfileRowStatus RowStatus hdsl2ShdslSpanConfProfileRowStatus RowStatus
} }
hdsl2ShdslSpanConfProfileName OBJECT-TYPE hdsl2ShdslSpanConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32)) SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is the unique index associated with this profile." "This object is the unique index associated with this profile.
Entries in this table are referenced via the object
hdsl2ShdslSpanConfProfile in Hdsl2ShdslSpanConfEntry."
::= { hdsl2ShdslSpanConfProfileEntry 1 } ::= { hdsl2ShdslSpanConfProfileEntry 1 }
hdsl2ShdslSpanConfWireInterface OBJECT-TYPE hdsl2ShdslSpanConfWireInterface OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
twoWire(1), twoWire(1),
fourWire(2) fourWire(2)
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the two-wire or optional four-wire "This object configures the two-wire or optional four-wire
operation for SHDSL Lines." operation for SHDSL Lines."
DEFVAL { twoWire }
Expires October 2, 2001 Page [33]
::= { hdsl2ShdslSpanConfProfileEntry 2 } ::= { hdsl2ShdslSpanConfProfileEntry 2 }
hdsl2ShdslSpanConfMinLineRate OBJECT-TYPE hdsl2ShdslSpanConfMinLineRate OBJECT-TYPE
SYNTAX Integer32 SYNTAX INTEGER(0..4112000)
UNITS "bps" UNITS "bps"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the minimum transmission rate for "This object configures the minimum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered (hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum 'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'." line rate, the line rate is considered 'rate-adaptive'."
DEFVAL { 1552000 }
::= { hdsl2ShdslSpanConfProfileEntry 3 } ::= { hdsl2ShdslSpanConfProfileEntry 3 }
hdsl2ShdslSpanConfMaxLineRate OBJECT-TYPE hdsl2ShdslSpanConfMaxLineRate OBJECT-TYPE
SYNTAX Integer32 SYNTAX INTEGER(0..4112000)
UNITS "bps" UNITS "bps"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the maximum transmission rate for "This object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered (hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum 'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'." line rate, the line rate is considered 'rate-adaptive'."
DEFVAL { 1552000 }
::= { hdsl2ShdslSpanConfProfileEntry 4 } ::= { hdsl2ShdslSpanConfProfileEntry 4 }
hdsl2ShdslSpanConfPSD OBJECT-TYPE hdsl2ShdslSpanConfPSD OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
symmetric(1), symmetric(1),
asymmetric(2) asymmetric(2)
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures use of symmetric/asymmetric PSD (Power "This object configures use of symmetric/asymmetric PSD (Power
Spectral Density) Mask for the associated SHDSL Line. Support Spectral Density) Mask for the associated SHDSL Line. Support
for symmetric PSD is mandatory for all supported data rates. for symmetric PSD is mandatory for all supported data rates.
Support for asymmetric PSD is optional." Support for asymmetric PSD is optional."
DEFVAL { symmetric }
::= { hdsl2ShdslSpanConfProfileEntry 5 } ::= { hdsl2ShdslSpanConfProfileEntry 5 }
hdsl2ShdslSpanConfTransmissionMode OBJECT-TYPE hdsl2ShdslSpanConfTransmissionMode OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object specifies the regional setting for the SHDSL "This object specifies the regional setting for the SHDSL
line." line."
DEFVAL { region1 }
::= { hdsl2ShdslSpanConfProfileEntry 6 } ::= { hdsl2ShdslSpanConfProfileEntry 6 }
hdsl2ShdslSpanConfRemoteEnabled OBJECT-TYPE hdsl2ShdslSpanConfRemoteEnabled OBJECT-TYPE
Expires October 2, 2001 Page [34]
SYNTAX INTEGER SYNTAX INTEGER
{ {
enabled(1), enabled(1),
disabled(2) disabled(2)
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object enables/disables support for remote management "This object enables/disables support for remote management
of the units in a SHDSL line from the STU-R via the EOC." of the units in a SHDSL line from the STU-R via the EOC."
DEFVAL { enabled }
::= { hdsl2ShdslSpanConfProfileEntry 7 } ::= { hdsl2ShdslSpanConfProfileEntry 7 }
hdsl2ShdslSpanConfPowerFeeding OBJECT-TYPE hdsl2ShdslSpanConfPowerFeeding OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
noPower(1), noPower(1),
powerFeed(2), powerFeed(2),
wettingCurrent(3) wettingCurrent(3)
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object enables/disables support for optional power "This object enables/disables support for optional power
feeding in a SHDSL line." feeding in a SHDSL line."
DEFVAL { noPower }
::= { hdsl2ShdslSpanConfProfileEntry 8 } ::= { hdsl2ShdslSpanConfProfileEntry 8 }
hdsl2ShdslSpanConfCurrCondTargetMarginDown OBJECT-TYPE hdsl2ShdslSpanConfCurrCondTargetMarginDown OBJECT-TYPE
SYNTAX INTEGER(-10..21) SYNTAX INTEGER(-10..21)
UNITS "dB" UNITS "dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object specifies the downstream current condition target "This object specifies the downstream current condition target
SNR margin for a SHDSL line. The SNR margin is the difference SNR margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit." is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 9 } ::= { hdsl2ShdslSpanConfProfileEntry 9 }
hdsl2ShdslSpanConfWorstCaseTargetMarginDown OBJECT-TYPE hdsl2ShdslSpanConfWorstCaseTargetMarginDown OBJECT-TYPE
SYNTAX INTEGER(-10..21) SYNTAX INTEGER(-10..21)
UNITS "dB" UNITS "dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object specifies the downstream worst case target SNR "This object specifies the downstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR between the desired SNR and the actual SNR. Target SNR
margin is the desired SNR margin for a unit." margin is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 10 } ::= { hdsl2ShdslSpanConfProfileEntry 10 }
hdsl2ShdslSpanConfCurrCondTargetMarginUp OBJECT-TYPE hdsl2ShdslSpanConfCurrCondTargetMarginUp OBJECT-TYPE
SYNTAX INTEGER(-10..21) SYNTAX INTEGER(-10..21)
UNITS "dB" UNITS "dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
Expires October 2, 2001 Page [35]
DESCRIPTION DESCRIPTION
"This object specifies the upstream current condition target "This object specifies the upstream current condition target
SNR margin for a SHDSL line. The SNR margin is the difference SNR margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit." is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 11 } ::= { hdsl2ShdslSpanConfProfileEntry 11 }
hdsl2ShdslSpanConfWorstCaseTargetMarginUp OBJECT-TYPE hdsl2ShdslSpanConfWorstCaseTargetMarginUp OBJECT-TYPE
SYNTAX INTEGER(-10..21) SYNTAX INTEGER(-10..21)
UNITS "dB" UNITS "dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object specifies the upstream worst case target SNR "This object specifies the upstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit." is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 12 } ::= { hdsl2ShdslSpanConfProfileEntry 12 }
hdsl2ShdslSpanConfUsedTargetMargins OBJECT-TYPE hdsl2ShdslSpanConfUsedTargetMargins OBJECT-TYPE
SYNTAX Integer32 SYNTAX BITS
{
currCondDown(0),
worstCaseDown(1),
currCondUp(2),
worstCaseUp(3)
}
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Contains indicates whether a target SNR margin is enabled or "Contains indicates whether a target SNR margin is enabled or
disabled. This is a bit-map of possible settings. The disabled. This is a bit-map of possible settings. The
various bit positions are: various bit positions are:
1 currCondDown current condition downstream target SNR currCondDown current condition downstream target SNR
margin enabled margin enabled
2 worstCaseDown worst case downstream target SNR margin worstCaseDown worst case downstream target SNR margin
enabled enabled
4 currCondUp current condition upstream target SNR currCondUp current condition upstream target SNR
margin enabled margin enabled
8 worstCaseUp worst case upstream target SNR margin worstCaseUp worst case upstream target SNR margin
enabled." enabled."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 13 } ::= { hdsl2ShdslSpanConfProfileEntry 13 }
hdsl2ShdslSpanConfProfileRowStatus OBJECT-TYPE hdsl2ShdslSpanConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus SYNTAX RowStatus
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object controlls creation/deletion of the associated "This object controls creation/deletion of the associated
entry in this table per the semantics of RowStatus." entry in this table per the semantics of RowStatus. If an
active entry is referenced in hdsl2ShdslSpanConfProfile, the
entry MUST remain active until all references are removed."
::= { hdsl2ShdslSpanConfProfileEntry 14 } ::= { hdsl2ShdslSpanConfProfileEntry 14 }
-- Segment Endpoint Alarm Configuration Profile group -- Segment Endpoint Alarm Configuration Profile group
-- --
hdsl2ShdslEndpointAlarmConfProfileTable OBJECT-TYPE hdsl2ShdslEndpointAlarmConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointAlarmConfProfileEntry SYNTAX SEQUENCE OF Hdsl2ShdslEndpointAlarmConfProfileEntry
Expires October 2, 2001 Page [36]
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table supports definitions of alarm configuration "This table supports definitions of alarm configuration
profiles for HDSL2/SHDSL segment endoints." profiles for HDSL2/SHDSL segment endpoints. This table
MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 11 } ::= { hdsl2ShdslMibObjects 11 }
hdsl2ShdslEndpointAlarmConfProfileEntry OBJECT-TYPE hdsl2ShdslEndpointAlarmConfProfileEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointAlarmConfProfileEntry SYNTAX Hdsl2ShdslEndpointAlarmConfProfileEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Each entry corresponds to a single alarm configuration profile. "Each entry corresponds to a single alarm configuration profile.
Each profile contains a set of parameters for setting alarm Each profile contains a set of parameters for setting alarm
thresholds for various performance attributes monitored at thresholds for various performance attributes monitored at
HDSL2/SHDSL segment endpoints. Profiles may be created/deleted HDSL2/SHDSL segment endpoints. Profiles may be created/deleted
using the row creation/deletion mechanism via using the row creation/deletion mechanism via
hdsl2ShdslEndpointAlarmConfProfileRowStatus. Profiles that hdsl2ShdslEndpointAlarmConfProfileRowStatus. If an active
are being referenced may not be deleted." entry is referenced in either hdsl2ShdslSpanConfAlarmProfile
or hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
active until all references are removed."
INDEX { IMPLIED hdsl2ShdslEndpointAlarmConfProfileName } INDEX { IMPLIED hdsl2ShdslEndpointAlarmConfProfileName }
::= { hdsl2ShdslEndpointAlarmConfProfileTable 1 } ::= { hdsl2ShdslEndpointAlarmConfProfileTable 1 }
Hdsl2ShdslEndpointAlarmConfProfileEntry ::= Hdsl2ShdslEndpointAlarmConfProfileEntry ::=
SEQUENCE SEQUENCE
{ {
hdsl2ShdslEndpointAlarmConfProfileName SnmpAdminString, hdsl2ShdslEndpointAlarmConfProfileName SnmpAdminString,
hdsl2ShdslEndpointThreshLoopAttenuation Integer32, hdsl2ShdslEndpointThreshLoopAttenuation INTEGER,
hdsl2ShdslEndpointThreshSNRMargin Integer32, hdsl2ShdslEndpointThreshSNRMargin INTEGER,
hdsl2ShdslEndpointThreshES hdsl2ShdslEndpointThreshES
Hdsl2ShdslPerfIntervalThreshold, Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshSES hdsl2ShdslEndpointThreshSES
Hdsl2ShdslPerfIntervalThreshold, Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshCRCanomalies Integer32, hdsl2ShdslEndpointThreshCRCanomalies Integer32,
hdsl2ShdslEndpointThreshLOSWS hdsl2ShdslEndpointThreshLOSWS
Hdsl2ShdslPerfIntervalThreshold, Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshUAS hdsl2ShdslEndpointThreshUAS
Hdsl2ShdslPerfIntervalThreshold, Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointAlarmConfProfileRowStatus RowStatus hdsl2ShdslEndpointAlarmConfProfileRowStatus RowStatus
skipping to change at line 2103 skipping to change at page 42, line 20
hdsl2ShdslEndpointAlarmConfProfileName OBJECT-TYPE hdsl2ShdslEndpointAlarmConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32)) SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is the unique index associated with this profile." "This object is the unique index associated with this profile."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 1 } ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 1 }
hdsl2ShdslEndpointThreshLoopAttenuation OBJECT-TYPE hdsl2ShdslEndpointThreshLoopAttenuation OBJECT-TYPE
SYNTAX Integer32 SYNTAX INTEGER(-127..128)
UNITS "dB" UNITS "dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the loop attentuation alarm threshold. "This object configures the loop attenuation alarm threshold.
When the current value of hdsl2ShdslEndpointCurrAtn reaches
Expires October 2, 2001 Page [37] or drops below this threshold, a hdsl2ShdslLoopAttenCrossing
When the current value reaches or drops below this threshold, MAY be generated."
a hdsl2ShdslLoopAttenCrossing will be generated." DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 2 } ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 2 }
hdsl2ShdslEndpointThreshSNRMargin OBJECT-TYPE hdsl2ShdslEndpointThreshSNRMargin OBJECT-TYPE
SYNTAX Integer32 SYNTAX INTEGER(-127..128)
UNITS "dB" UNITS "dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the SNR margin alarm threshold. "This object configures the SNR margin alarm threshold.
When the current value reaches or drops below this threshold, When the current value of hdsl2ShdslEndpointCurrSnrMgn
a hdsl2ShdslSNRMarginCrossing will be generated." reaches or drops below this threshold, a
hdsl2ShdslSNRMarginCrossing MAY be generated."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 3 } ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 3 }
hdsl2ShdslEndpointThreshES OBJECT-TYPE hdsl2ShdslEndpointThreshES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the threshold for the number of "This object configures the threshold for the number of
errored seconds (ES) within any given 15-minute performance errored seconds (ES) within any given 15-minute performance
data collection interval. If the value of errored seconds data collection interval. If the value of errored seconds
in a particular 15-minute collection interval reaches/ in a particular 15-minute collection interval reaches/
exceeds this value, a hdsl2ShdslPerfESThresh will be exceeds this value, a hdsl2ShdslPerfESThresh MAY be
generated. One notification will be sent per interval per generated. At most one notification will be sent per
endpoint." interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 4 } ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 4 }
hdsl2ShdslEndpointThreshSES OBJECT-TYPE hdsl2ShdslEndpointThreshSES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the threshold for the number of "This object configures the threshold for the number of
severely errored seconds (SES) within any given 15-minute severely errored seconds (SES) within any given 15-minute
performance data collection interval. If the value of performance data collection interval. If the value of
severely errored seconds in a particular 15-minute collection severely errored seconds in a particular 15-minute collection
interval reaches/exceeds this value, a hdsl2ShdslPerfSESThresh interval reaches/exceeds this value, a hdsl2ShdslPerfSESThresh
will be generated. One notification will be sent per interval MAY be generated. At most one notification will be sent per
per endpoint." interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 5 } ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 5 }
hdsl2ShdslEndpointThreshCRCanomalies OBJECT-TYPE hdsl2ShdslEndpointThreshCRCanomalies OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
UNITS "detected CRC Anomalies"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the threshold for the number of "This object configures the threshold for the number of
CRC anomalies within any given 15-minute performance data CRC anomalies within any given 15-minute performance data
collection interval. If the value of CRC anomalies in a collection interval. If the value of CRC anomalies in a
particular 15-minute collection interval reaches/exceeds particular 15-minute collection interval reaches/exceeds
this value, a hdsl2ShdslPerfCRCanomaliesThresh will be this value, a hdsl2ShdslPerfCRCanomaliesThresh MAY be
generated. At most one notification will be sent per
Expires October 2, 2001 Page [38] interval per endpoint."
generated. One notification will be sent per interval per DEFVAL { 0 }
endpoint."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 6 } ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 6 }
hdsl2ShdslEndpointThreshLOSWS OBJECT-TYPE hdsl2ShdslEndpointThreshLOSWS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the threshold for the number of "This object configures the threshold for the number of
Loss of Sync Word (LOSW) Seconds within any given 15-minute Loss of Sync Word (LOSW) Seconds within any given 15-minute
performance data collection interval. If the value of LOSW performance data collection interval. If the value of LOSW
in a particular 15-minute collection interval reaches/exceeds in a particular 15-minute collection interval reaches/exceeds
this value, a hdsl2ShdslPerfLOSWSThresh will be generated. this value, a hdsl2ShdslPerfLOSWSThresh MAY be generated.
One notification will be sent per interval per endpoint." At most one notification will be sent per interval per
endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 7 } ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 7 }
hdsl2ShdslEndpointThreshUAS OBJECT-TYPE hdsl2ShdslEndpointThreshUAS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the threshold for the number of "This object configures the threshold for the number of
unavailable seconds (UAS) within any given 15-minute unavailable seconds (UAS) within any given 15-minute
performance data collection interval. If the value of UAS performance data collection interval. If the value of UAS
in a particular 15-minute collection interval reaches/exceeds in a particular 15-minute collection interval reaches/exceeds
this value, a hdsl2ShdslPerfUASThresh will be generated. this value, a hdsl2ShdslPerfUASThresh MAY be generated.
One notification will be sent per interval per endpoint." At most one notification will be sent per interval per
endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 8 } ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 8 }
hdsl2ShdslEndpointAlarmConfProfileRowStatus OBJECT-TYPE hdsl2ShdslEndpointAlarmConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus SYNTAX RowStatus
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object controls creation/deletion of the associated "This object controls creation/deletion of the associated
entry in this table as per the semantics of RowStatus." entry in this table as per the semantics of RowStatus.
If an active entry is referenced in either
hdsl2ShdslSpanConfAlarmProfile or
hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
active until all references are removed."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 9 } ::= { hdsl2ShdslEndpointAlarmConfProfileEntry 9 }
-- Notifications Group -- Notifications Group
-- --
hdsl2ShdslNotifications OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 0 } hdsl2ShdslNotifications OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 0 }
hdsl2ShdslLoopAttenCrossing NOTIFICATION-TYPE hdsl2ShdslLoopAttenCrossing NOTIFICATION-TYPE
OBJECTS OBJECTS
{ {
hdsl2ShdslEndpointCurrAtn, hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointThreshLoopAttenuation hdsl2ShdslEndpointThreshLoopAttenuation
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This notification indicates that the loop attenuation "This notification indicates that the loop attenuation
Expires October 2, 2001 Page [39]
threshold (as per the hdsl2ShdslEndpointThreshLoopAttenuation threshold (as per the hdsl2ShdslEndpointThreshLoopAttenuation
value) has been reached/exceeded for the HDSL2/SHDSL segment value) has been reached/exceeded for the HDSL2/SHDSL segment
endpoint." endpoint."
::= { hdsl2ShdslNotifications 1 } ::= { hdsl2ShdslNotifications 1 }
hdsl2ShdslSNRMarginCrossing NOTIFICATION-TYPE hdsl2ShdslSNRMarginCrossing NOTIFICATION-TYPE
OBJECTS OBJECTS
{ {
hdsl2ShdslEndpointCurrSnrMgn, hdsl2ShdslEndpointCurrSnrMgn,
hdsl2ShdslEndpointThreshSNRMargin hdsl2ShdslEndpointThreshSNRMargin
skipping to change at line 2280 skipping to change at page 45, line 48
OBJECTS OBJECTS
{ {
hdsl2ShdslEndpointCurr15MinCRCanomalies, hdsl2ShdslEndpointCurr15MinCRCanomalies,
hdsl2ShdslEndpointThreshCRCanomalies hdsl2ShdslEndpointThreshCRCanomalies
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This notification indicates that the CRC anomalies threshold "This notification indicates that the CRC anomalies threshold
(as per the hdsl2ShdslEndpointThreshCRCanomalies value) has (as per the hdsl2ShdslEndpointThreshCRCanomalies value) has
been reached/exceeded for the HDSL2/SHDSL Segment Endpoint." been reached/exceeded for the HDSL2/SHDSL Segment Endpoint."
Expires October 2, 2001 Page [40]
::= { hdsl2ShdslNotifications 5 } ::= { hdsl2ShdslNotifications 5 }
hdsl2ShdslPerfLOSWSThresh NOTIFICATION-TYPE hdsl2ShdslPerfLOSWSThresh NOTIFICATION-TYPE
OBJECTS OBJECTS
{ {
hdsl2ShdslEndpointCurr15MinLOSWS, hdsl2ShdslEndpointCurr15MinLOSWS,
hdsl2ShdslEndpointThreshLOSWS hdsl2ShdslEndpointThreshLOSWS
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
skipping to change at line 2337 skipping to change at page 46, line 50
hdsl2ShdslMaintLoopbackConfig hdsl2ShdslMaintLoopbackConfig
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This notification indicates that an endpoint maintenance "This notification indicates that an endpoint maintenance
loopback command failed for an HDSL2/SHDSL segment." loopback command failed for an HDSL2/SHDSL segment."
::= { hdsl2ShdslNotifications 9 } ::= { hdsl2ShdslNotifications 9 }
hdsl2ShdslpowerBackoff NOTIFICATION-TYPE hdsl2ShdslpowerBackoff NOTIFICATION-TYPE
OBJECTS OBJECTS
Expires October 2, 2001 Page [41]
{ {
hdsl2ShdslEndpointCurrStatus hdsl2ShdslEndpointCurrStatus
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This notification indicates that the bit setting for "This notification indicates that the bit setting for
powerBackoff in the hdsl2ShdslEndpointCurrStatus object for powerBackoff in the hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed." this endpoint has changed."
::= { hdsl2ShdslNotifications 10 } ::= { hdsl2ShdslNotifications 10 }
skipping to change at line 2394 skipping to change at page 47, line 52
hdsl2ShdslprotocolInitFailure NOTIFICATION-TYPE hdsl2ShdslprotocolInitFailure NOTIFICATION-TYPE
OBJECTS OBJECTS
{ {
hdsl2ShdslEndpointCurrStatus hdsl2ShdslEndpointCurrStatus
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This notification indicates that the bit setting for "This notification indicates that the bit setting for
protocolInitFailure in the hdsl2ShdslEndpointCurrStatus protocolInitFailure in the hdsl2ShdslEndpointCurrStatus
Expires October 2, 2001 Page [42]
object for this endpoint has changed." object for this endpoint has changed."
::= { hdsl2ShdslNotifications 14 } ::= { hdsl2ShdslNotifications 14 }
hdsl2ShdslnoNeighborPresent NOTIFICATION-TYPE hdsl2ShdslnoNeighborPresent NOTIFICATION-TYPE
OBJECTS OBJECTS
{ {
hdsl2ShdslEndpointCurrStatus hdsl2ShdslEndpointCurrStatus
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This notification indicates that the bit setting for "This notification indicates that the bit setting for
noNeighborPresent in the hdsl2ShdslEndpointCurrStatus object noNeighborPresent in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed." for this endpoint has changed."
::= { hdsl2ShdslNotifications 15 } ::= { hdsl2ShdslNotifications 15 }
hdsl2ShdsllocalPowerLoss NOTIFICATION-TYPE hdsl2ShdslLocalPowerLoss NOTIFICATION-TYPE
OBJECTS OBJECTS
{ {
ifIndex, ifIndex,
hdsl2ShdslInvIndex hdsl2ShdslInvIndex
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This notification indicates impending unit failure due to "This notification indicates impending unit failure due to
loss of local power (last gasp)." loss of local power (last gasp)."
::= { hdsl2ShdslNotifications 16 } ::= { hdsl2ShdslNotifications 16 }
-- conformance information -- conformance information
-- --
hdsl2ShdslConformance OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 3 } hdsl2ShdslConformance OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 3 }
hdsl2ShdslGroups OBJECT IDENTIFIER ::= { hdsl2ShdslConformance 1 } hdsl2ShdslGroups OBJECT IDENTIFIER ::=
hdsl2ShdslCompliances OBJECT IDENTIFIER ::= { hdsl2ShdslConformance 2 } { hdsl2ShdslConformance 1 }
hdsl2ShdslCompliances OBJECT IDENTIFIER ::=
{ hdsl2ShdslConformance 2 }
-- agent compliance statements -- agent compliance statements
hdsl2ShdslLineMibCompliance MODULE-COMPLIANCE hdsl2ShdslLineMibCompliance MODULE-COMPLIANCE
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The section outlines compliance requirements for this MIB." "The section outlines compliance requirements for this MIB."
MODULE MODULE
MANDATORY-GROUPS MANDATORY-GROUPS
{ {
skipping to change at line 2451 skipping to change at page 48, line 56
hdsl2ShdslInventoryGroup, hdsl2ShdslInventoryGroup,
hdsl2ShdslEndpointConfGroup, hdsl2ShdslEndpointConfGroup,
hdsl2ShdslEndpointCurrGroup, hdsl2ShdslEndpointCurrGroup,
hdsl2Shdsl15MinIntervalGroup, hdsl2Shdsl15MinIntervalGroup,
hdsl2Shdsl1DayIntervalGroup, hdsl2Shdsl1DayIntervalGroup,
hdsl2ShdslMaintenanceGroup, hdsl2ShdslMaintenanceGroup,
hdsl2ShdslEndpointAlarmConfGroup, hdsl2ShdslEndpointAlarmConfGroup,
hdsl2ShdslNotificationGroup hdsl2ShdslNotificationGroup
} }
Expires October 2, 2001 Page [43]
GROUP hdsl2ShdslInventoryShdslGroup GROUP hdsl2ShdslInventoryShdslGroup
DESCRIPTION DESCRIPTION
"Support for this group is only required for implementations "Support for this group is only required for implementations
supporting SHDSL lines." supporting SHDSL lines."
GROUP hdsl2ShdslSpanShdslStatusGroup GROUP hdsl2ShdslSpanShdslStatusGroup
DESCRIPTION DESCRIPTION
"Support for this group is only required for implementations "Support for this group is only required for implementations
supporting SHDSL lines." supporting SHDSL lines."
skipping to change at line 2507 skipping to change at page 50, line 4
hdsl2ShdslInventoryShdslGroup OBJECT-GROUP hdsl2ShdslInventoryShdslGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
hdsl2ShdslInvTransmissionModeCapability hdsl2ShdslInvTransmissionModeCapability
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects for retrieving SHDSL-specific "This group supports objects for retrieving SHDSL-specific
inventory information." inventory information."
::= { hdsl2ShdslGroups 3 } ::= { hdsl2ShdslGroups 3 }
Expires October 2, 2001 Page [44]
hdsl2ShdslSpanShdslStatusGroup OBJECT-GROUP hdsl2ShdslSpanShdslStatusGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
hdsl2ShdslStatusMaxAttainableLineRate, hdsl2ShdslStatusMaxAttainableLineRate,
hdsl2ShdslStatusActualLineRate, hdsl2ShdslStatusActualLineRate,
hdsl2ShdslStatusTransmissionModeCurrent hdsl2ShdslStatusTransmissionModeCurrent
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects for retrieving SHDSL-specific "This group supports objects for retrieving SHDSL-specific
skipping to change at line 2565 skipping to change at page 51, line 7
::= { hdsl2ShdslGroups 6 } ::= { hdsl2ShdslGroups 6 }
hdsl2ShdslEndpointCurrGroup OBJECT-GROUP hdsl2ShdslEndpointCurrGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
hdsl2ShdslEndpointSide, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2ShdslEndpointWirePair,
hdsl2ShdslEndpointCurrAtn, hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointCurrSnrMgn, hdsl2ShdslEndpointCurrSnrMgn,
hdsl2ShdslEndpointCurrStatus, hdsl2ShdslEndpointCurrStatus,
Expires October 2, 2001 Page [45]
hdsl2ShdslEndpointES, hdsl2ShdslEndpointES,
hdsl2ShdslEndpointSES, hdsl2ShdslEndpointSES,
hdsl2ShdslEndpointCRCanomalies, hdsl2ShdslEndpointCRCanomalies,
hdsl2ShdslEndpointLOSWS, hdsl2ShdslEndpointLOSWS,
hdsl2ShdslEndpointUAS, hdsl2ShdslEndpointUAS,
hdsl2ShdslEndpointCurr15MinTimeElapsed, hdsl2ShdslEndpointCurr15MinTimeElapsed,
hdsl2ShdslEndpointCurr15MinES, hdsl2ShdslEndpointCurr15MinES,
hdsl2ShdslEndpointCurr15MinSES, hdsl2ShdslEndpointCurr15MinSES,
hdsl2ShdslEndpointCurr15MinCRCanomalies, hdsl2ShdslEndpointCurr15MinCRCanomalies,
hdsl2ShdslEndpointCurr15MinLOSWS, hdsl2ShdslEndpointCurr15MinLOSWS,
skipping to change at line 2622 skipping to change at page 52, line 9
hdsl2Shdsl1DayIntervalES, hdsl2Shdsl1DayIntervalES,
hdsl2Shdsl1DayIntervalSES, hdsl2Shdsl1DayIntervalSES,
hdsl2Shdsl1DayIntervalCRCanomalies, hdsl2Shdsl1DayIntervalCRCanomalies,
hdsl2Shdsl1DayIntervalLOSWS, hdsl2Shdsl1DayIntervalLOSWS,
hdsl2Shdsl1DayIntervalUAS hdsl2Shdsl1DayIntervalUAS
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports objects which maintain historic "This group supports objects which maintain historic
performance measurements relating to segment endpoints in performance measurements relating to segment endpoints in
Expires October 2, 2001 Page [46]
HDSL2/SHDSL lines in 1-day intervals." HDSL2/SHDSL lines in 1-day intervals."
::= { hdsl2ShdslGroups 9 } ::= { hdsl2ShdslGroups 9 }
hdsl2ShdslMaintenanceGroup OBJECT-GROUP hdsl2ShdslMaintenanceGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
hdsl2ShdslMaintLoopbackConfig, hdsl2ShdslMaintLoopbackConfig,
hdsl2ShdslMaintTipRingReversal, hdsl2ShdslMaintTipRingReversal,
hdsl2ShdslMaintPowerBackOff, hdsl2ShdslMaintPowerBackOff,
hdsl2ShdslMaintSoftRestart, hdsl2ShdslMaintSoftRestart,
skipping to change at line 2679 skipping to change at page 53, line 11
hdsl2ShdslPerfCRCanomaliesThresh, hdsl2ShdslPerfCRCanomaliesThresh,
hdsl2ShdslPerfLOSWSThresh, hdsl2ShdslPerfLOSWSThresh,
hdsl2ShdslPerfUASThresh, hdsl2ShdslPerfUASThresh,
hdsl2ShdslSpanInvalidNumRepeaters, hdsl2ShdslSpanInvalidNumRepeaters,
hdsl2ShdslLoopbackFailure, hdsl2ShdslLoopbackFailure,
hdsl2ShdslpowerBackoff, hdsl2ShdslpowerBackoff,
hdsl2ShdsldeviceFault, hdsl2ShdsldeviceFault,
hdsl2ShdsldcContinuityFault, hdsl2ShdsldcContinuityFault,
hdsl2ShdslconfigInitFailure, hdsl2ShdslconfigInitFailure,
hdsl2ShdslprotocolInitFailure, hdsl2ShdslprotocolInitFailure,
Expires October 2, 2001 Page [47]
hdsl2ShdslnoNeighborPresent, hdsl2ShdslnoNeighborPresent,
hdsl2ShdsllocalPowerLoss hdsl2ShdslLocalPowerLoss
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports notifications of significant events/ "This group supports notifications of significant conditions
conditions associated with HDSL2/SHDSL lines." associated with HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 12 } ::= { hdsl2ShdslGroups 12 }
hdsl2ShdslSpanConfProfileGroup OBJECT-GROUP hdsl2ShdslSpanConfProfileGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
hdsl2ShdslSpanConfWireInterface, hdsl2ShdslSpanConfWireInterface,
hdsl2ShdslSpanConfMinLineRate, hdsl2ShdslSpanConfMinLineRate,
hdsl2ShdslSpanConfMaxLineRate, hdsl2ShdslSpanConfMaxLineRate,
hdsl2ShdslSpanConfPSD, hdsl2ShdslSpanConfPSD,
hdsl2ShdslSpanConfTransmissionMode, hdsl2ShdslSpanConfTransmissionMode,
skipping to change at line 2732 skipping to change at page 54, line 10
environment without proper protection can have a negative effect on environment without proper protection can have a negative effect on
network operations. network operations.
No managed objects in this MIB contain sensitive information. No managed objects in this MIB contain sensitive information.
SNMPv1 by itself is not a secure environment. Even if the network SNMPv1 by itself is not a secure environment. Even if the network
itself is secure (for example by using IPSec), even then, there is no itself is secure (for example by using IPSec), even then, there is no
control as to who on the secure network is allowed to access and control as to who on the secure network is allowed to access and
GET/SET (read/change/create/delete) the objects in this MIB. GET/SET (read/change/create/delete) the objects in this MIB.
It is recommended that the implementers consider the security It is recommended that the implementors consider the security
features as provided by the SNMPv3 framework. Specifically, the use features as provided by the SNMPv3 framework. Specifically, the use
of the User-based Security Model RFC 2574 [12] and the View- of the User-based Security Model RFC 2574 [12] and the View-
based Access Control Model RFC 2575 [15] is recommended. based Access Control Model (VACM) RFC 2575 [15] is recommended.
Expires October 2, 2001 Page [48]
It is then a customer/user responsibility to ensure that the SNMP It is then a customer/user responsibility to ensure that the SNMP
entity giving access to an instance of this MIB, is properly entity giving access to an instance of this MIB, is properly
configured to give access to the objects only to those principals configured to give access to the objects only to those principals
(users) that have legitimate rights to indeed GET or SET (users) that have legitimate rights to indeed GET or SET
(change/create/delete) them. (change/create/delete) them.
It should be noted that interface indices in this MIB are maintained
persistently. VACM data relating to these should be stored
persistently.
8. Acknowledgments 8. Acknowledgments
The authors are deeply grateful to the authors of the ADSL LINE MIB The authors are deeply grateful to the authors of the ADSL LINE MIB
(RFC 2662 [23]), Gregory Bathrick and Faye Ly, as much of the text (RFC 2662 [23]), Gregory Bathrick and Faye Ly, as much of the text
and structure of this document originates in their documents. and structure of this document originates in their documents.
The authors are also grateful to the authors of FR MFR MIB (RFC 3020 The authors are also grateful to the authors of FR MFR MIB (RFC 3020
[24]), Prayson Pate, Bob Lynch, and Kenneth Rehbehn, as the entirety [24]), Prayson Pate, Bob Lynch, and Kenneth Rehbehn, as the entirety
of the Security Considerations section was lifted from their document. of the Security Considerations section was lifted from their document.
skipping to change at line 2789 skipping to change at page 55, line 14
Mike Sneed (ECI) Mike Sneed (ECI)
Jon Turney (DSL Solutions) Jon Turney (DSL Solutions)
Aron Wahl (Memotec) Aron Wahl (Memotec)
Michael Wrobel (Memotec) Michael Wrobel (Memotec)
9. References 9. References
[1] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for [1] Harrington, D., Presuhn, R., and Wijnen, B., "An Architecture
Describing SNMP Management Frameworks", RFC 2571, April 1999. for Describing SNMP Management Frameworks", RFC 2571, April 1999.
[2] Rose, M., and K. McCloghrie, "Structure and Identification of
Expires October 2, 2001 Page [49]
[2] Rose, M., and McCloghrie, K., "Structure and Identification of
Management Information for TCP/IP-based Internets", STD 16, RFC Management Information for TCP/IP-based Internets", STD 16, RFC
1155, May 1990. 1155, May 1990.
[3] Rose, M., and K. McCloghrie, "Concise MIB Definitions", STD 16, [3] Rose, M., and McCloghrie, K., "Concise MIB Definitions", STD 16,
RFC 1212, March 1991. RFC 1212, March 1991.
[4] M. Rose, "A Convention for Defining Traps for use with the SNMP", [4] Rose, M., "A Convention for Defining Traps for use with the
RFC 1215, March 1991. SNMP", RFC 1215, March 1991.
[5] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, [5] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose,
M., and S. Waldbusser, "Structure of Management Information M., and Waldbusser, S., "Structure of Management Information Version
Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. 2 (SMIv2)", STD 58, RFC 2578, April 1999.
[6] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, [6] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose,
M., and S. Waldbusser, "Textual Conventions for SMIv2", STD 58, M., and Waldbusser, S., "Textual Conventions for SMIv2", STD 58,
RFC 2579, April 1999. RFC 2579, April 1999.
[7] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, [7] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose,
M., and S. Waldbusser, "Conformance Statements for SMIv2", STD 58, M., and Waldbusser, S., "Conformance Statements for SMIv2", STD 58,
RFC 2580, April 1999. RFC 2580, April 1999.
[8] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple [8] Case, J., Fedor, M., Schoffstall, M., and Davin, J., "Simple
Network Management Protocol", STD 15, RFC 1157, May 1990. Network Management Protocol", STD 15, RFC 1157, May 1990.
[9] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, [9] Case, J., McCloghrie, K., Rose, M., and Waldbusser, S.,
"Introduction to Community-based SNMPv2", RFC 1901, January "Introduction to Community-based SNMPv2", RFC 1901, January 1996.
1996.
[10] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Transport [10] Case, J., McCloghrie, K., Rose, M., and Waldbusser, S.,
Mappings for Version 2 of the Simple Network Management Protocol "Transport Mappings for Version 2 of the Simple Network Management
(SNMPv2)", RFC 1906, January 1996. Protocol (SNMPv2)", RFC 1906, January 1996.
[11] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message [11] Case, J., Harrington D., Presuhn, R., and Wijnen, B., "Message
Processing and Dispatching for the Simple Network Management Processing and Dispatching for the Simple Network Management
Protocol (SNMP)", RFC 2572, April 1999. Protocol (SNMP)", RFC 2572, April 1999.
[12] Blumenthal, U., and B. Wijnen, "User-based Security Model (USM) [12] Blumenthal, U., and Wijnen, B., "User-based Security Model (USM)
for version 3 of the Simple Network Management Protocol (SNMPv3)", for version 3 of the Simple Network Management Protocol (SNMPv3)",
RFC 2574, April 1999. RFC 2574, April 1999.
[13] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol [13] Case, J., McCloghrie, K., Rose, M., and Waldbusser, S.,
Operations for Version 2 of the Simple Network Management Protocol "Protocol Operations for Version 2 of the Simple Network Management
(SNMPv2)", RFC 1905, January 1996. Protocol (SNMPv2)", RFC 1905, January 1996.
[14] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC [14] Levi, D., Meyer, P., and Stewart, B., "SNMPv3 Applications",
2573, April 1999. RFC 2573, April 1999.
[15] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based Access [15] Wijnen, B., Presuhn, R., and McCloghrie, K., "View-based Access
Control Model (VACM) for the Simple Network Management Protocol Control Model (VACM) for the Simple Network Management Protocol
(SNMP)", RFC 2575, April 1999. (SNMP)", RFC 2575, April 1999.
[16] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction to [16] Case, J., Mundy, R., Partain, D., and Stewart, B., "Introduction
Version 3 of the Internet-standard Network Management Framework", to Version 3 of the Internet-standard Network Management Framework",
RFC 2570, April 1999. RFC 2570, April 1999.
Expires October 2, 2001 Page [50]
[17] Bradner, S., "Key Words for use in RFCs to Indicate Requirement [17] Bradner, S., "Key Words for use in RFCs to Indicate Requirement
Levels", RFC 2119, March 1997. Levels", RFC 2119, March 1997.
[18] American National Standards Institute, ANSI T1E1.4/2000-006, [18] American National Standards Institute, ANSI T1E1.4/2000-006,
February 2000. February 2000.
[19] Blackwell, S., Editor, "Single-Pair High-Speed Digital Subscriber [19] Blackwell, S., Editor, "Single-Pair High-Speed Digital
Line (SHDSL) Transceivers", ITU-T Draft G.991.2, April 2000. Subscriber Line (SHDSL) Transceivers", ITU-T Draft G.991.2, April
2000.
[20] McCloghrie, K., and M. Rose, Editors, "Management Information Base [20] McCloghrie, K., and Rose, M., Editors, "Management Information
for Network Management of TCP/IP-based internets: MIB-II", STD 17, Base for Network Management of TCP/IP-based internets: MIB-II", STD
RFC 1213, March 1991. 17, RFC 1213, March 1991.
[21] McCloghrie, K., and Kastenholz, F., "The Interfaces Group MIB", [21] McCloghrie, K., and Kastenholz, F., "The Interfaces Group MIB",
RFC 2863, June 2000. RFC 2863, June 2000.
[22] Tesink, K., "Textual Conventions for MIB Modules Using Performance [22] Tesink, K., "Textual Conventions for MIB Modules Using
History Based on 15 Minute Intervals", RFC 2493, January 1999. Performance History Based on 15 Minute Intervals", RFC 2493, January
1999.
[23] Bathrick, G., Ly, F., "Definitions of Managed Objects for the ADSL [23] Bathrick, G., Ly, F., "Definitions of Managed Objects for the
Lines", RFC 2662, August 1999. ADSL Lines", RFC 2662, August 1999.
[24] Pate, P., Lynch, B., Rehbehn, K., "Definitions of Managed Objects [24] Pate, P., Lynch, B., Rehbehn, K., "Definitions of Managed
for Monitoring and Controlling the UNI/NNI Multilink Frame Relay Objects for Monitoring and Controlling the UNI/NNI Multilink Frame
Function", RFC 3020, December 2000. Relay Function", RFC 3020, December 2000.
10. Intellectual Property Notice 10. Intellectual Property Notice
The IETF takes no position regarding the validity or scope of any The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and IETF's procedures with respect to rights in standards-track and
skipping to change at line 2907 skipping to change at page 57, line 23
rights which may cover technology that may be required to practice rights which may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive this standard. Please address the information to the IETF Executive
Director. Director.
11. Authors' Addresses 11. Authors' Addresses
Rajesh Abbi Rajesh Abbi
Alcatel USA Alcatel USA
2912 Wake Forest Road 2912 Wake Forest Road
Raleigh, NC 27609-7860 USA Raleigh, NC 27609-7860 USA
Tel: +1 919-950-6194 Tel: +1 919-850-6194
Fax: +1 919-850-6670
Expires October 2, 2001 Page [51]
Fax: +1 919-950-6670
E-mail: Rajesh.Abbi@usa.alcatel.com E-mail: Rajesh.Abbi@usa.alcatel.com
Bob Ray Bob Ray
Verilink Corporation Verilink Corporation
950 Explorer Blvd 950 Explorer Blvd
Huntsville, AL 35806 USA Huntsville, AL 35806 USA
Tel: +1 256-327-2380 Tel: +1 256-327-2380
Fax: +1 256-327-2880 Fax: +1 256-327-2880
E-mail: bray@verilink.com E-mail: bray@verilink.com
12. Full Copyright Statement 12. Full Copyright Statement
Copyright (C) The Internet Society (1999). All Rights Reserved. Copyright (C) The Internet Society (2001). All Rights Reserved.
This document and translations of it may be copied and furnished to This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of Internet organizations, except as needed for the purpose of
skipping to change at line 2948 skipping to change at line 2988
English. English.
The limited permissions granted above are perpetual and will not be The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns. revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Expires October 2, 2001 Page [52]
 End of changes. 

This html diff was produced by rfcdiff 1.23, available from http://www.levkowetz.com/ietf/tools/rfcdiff/