Network Working Group                                          M. Dodge
Category: Internet Draft                          Infineon Technologies
Document: draft-ietf-adslmib-vdsl-ext-mcm-00.txt draft-ietf-adslmib-vdsl-ext-mcm-01.txt                 B. Ray
                                                 PESA Switching Systems
                                                        September 2003
                                                          February 2004

         Definitions of Managed Object Extensions
	 for Very High Speed Digital Subscriber Lines (VDSL) Using
         Multiple Carrier Modulation (MCM) Line Coding.

Status of this Memo

   This document is an Internet-Draft and is in full conformance with
   all provisions of Section 10 of RFC2026.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as
   Internet-Drafts.

   Internet-Drafts are draft documents valid for a maximum of six
   months and may be updated, replaced, or obsoleted by other documents
   at any time.  It is inappropriate to use Internet-Drafts as
   reference material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at:
     http://www.ietf.org/ietf/1id-abstracts.txt

   The list of Internet-Draft Shadow Directories can be accessed at:
   http://www.ietf.org/shadow.html.

Copyright Notice

   Copyright (C) The Internet Society (2003). (2004).  All Rights Reserved.

Abstract

   This document defines a portion of the Management Information Base
   (MIB) module for use with network management protocols in the
   Internet community.  In particular, it describes objects used for
   managing the Line Code Specific parameters of Very High Speed
   Digital Subscriber Line (VDSL) interfaces using Multiple Carrier
   Modulation (MCM) Line Coding.  It is an optional extension to the
   VDSL-LINE CORE MIB RFC XXXX [RFCXXXX] which handles the line code
   independent objects.

Table of Contents

1.  The Internet-Standard Management Framework ....................   2
2.  Overview ......................................................   2
2.1 Relationship of this MIB Module to other MIB Modules          .   2
2.2 Conventions used in the MIB Module ............................   3
2.3 Structure .....................................................   3
2.4 Persistence ...................................................   4
3.  Conformance and Compliance ....................................   5
4.  Definitions ...................................................   5
5.  Intellectual Property .........................................  18  19
6.  Normative References ..........................................  18  19
7.  Informative References ........................................  19  20
8.  Security Considerations .......................................  19  21
9.  Acknowledgements ..............................................  20  21
10. Authors' Addresses ............................................  21  22
11. Full Copyright Statement ......................................  21  22

1.  The Internet-Standard Management Framework

   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to section 7 of
   RFC 3410 [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  MIB objects are generally
   accessed through the Simple Network Management Protocol (SNMP).
   Objects in the MIB are defined using the mechanisms defined in the
   Structure of Management Information (SMI).  This memo specifies a
   MIB module that is compliant to the SMIv2, which is described in STD
   58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC
   2580 [RFC2580].

2.  Overview

   This document describes an SNMP MIB module for managing the line
   code dependent (Physical Medium Dependent) Layer of MCM VDSL Lines.
   These definitions are based upon the specifications for VDSL as
   defined in T1E1, ETSI, and ITU documentation [T1E1311, T1E1011,
   T1E1013, ETSI2701, ETSI2702, ITU9931, ITU9971]. Additionally the
   protocol-dependent (and line-code dependent) management framework
   for VDSL lines specified by DSLF has been taken into consideration
   [DSLFXXXXXX].

   The MIB module is located in the MIB tree under MIB 2 transmission,
   as discussed in the MIB-2 Integration (RFC 2863 [RFC2863]) section
   of this document.

2.1  Relationship of this MIB Module to other MIB Modules

   The relationship of the VDSL Line MIB to other MIBS and in particular
   to the IF-MIB, as presented in RFC 2863 [RFC2863], is discussed in
   the VDSL-LINE CORE MIB RFC XXXX [RFCXXXX]. This section outlines the
   relationship of this VDSL Line Extension MIB to the VDSL-LINE CORE
   MIB RFC XXXX [RFCXXXX].

2.2 Conventions used in the MIB Module

2.2.1 Naming Conventions

   A.  Vtuc -- (VTUC) transceiver at near (Central) end of line
   B.  Vtur -- (VTUR) transceiver at Remote end of line
   C.  Vtu  -- One of either Vtuc or Vtur
   D.  Curr -- Current
   E.  Prev -- Previous
   F.  Atn  -- Attenuation
   G.  ES   -- Errored Second
   H.  SES  -- Severely Errored Second
   I.  UAS  -- Unavailable Second
   J.  LCS  -- Line Code Specific
   K.  Lof  -- Loss of Frame
   L.  Lol  -- Loss of Link
   M.  Los  -- Loss of Signal
   N.  Lpr  -- Loss of Power
   O.  xxxs -- Sum of Seconds in which xxx has occurs (e.g., xxx=Lof,
               Los, Lpr, Lol)
   P.  Max  -- Maximum
   Q.  Mgn  -- Margin
   R.  Min  -- Minimum
   S.  Psd  -- Power Spectral Density
   T.  Snr  -- Signal to Noise Ratio
   U.  Tx   -- Transmit
   V.  Blks -- Blocks

2.3  Structure

   The MCM VDSL Line Extension MIB contains the following MIB group:

   o   vdslMCMGroup :

   This group supports MIB objects for defining configuration profiles
   and for montioring individual bands of Multiple Carrier Modulation
   (MCM) VDSL modems.  It contains the following tables:

       - vdslLineMCMConfProfileTable
       - vdslLineMCMConfProfileTxBandTable
       - vdslLineMCMConfProfileRxBandTable
       - vdslLineMCMConfProfileTxPSDTable
       - vdslLineMCMConfProfileMaxTxPSDTable
       - vdslLineMCMConfProfileMaxRxPSDTable

   Either none, some or all of the objects in this group MAY be
   implemented for MCM VDSL lines.

   Figure 1, below, displays the relationship of the tables in the
   vdslMCMGroup to the vdslGroup and to the ifEntry:

     ifEntry(ifType=97)  ----> vdslLineTableEntry 1:(0..1)

      vdslLineTableEntry (vdslLineCoding=MCM)

      vdslLineConfProfileEntry(vdslLineConfProfileName)
                 ----> vdslLineMCMConfProfileTable 1:(0..1)
                 ----> vdslLineMCMConfProfileTxBandTable 1:(0..1)
                 ----> vdslLineMCMConfProfileRxBandTable 1:(0..1)
                 ----> vdslLineMCMConfProfileTxPSDTable 1:(0..1)
                 ----> vdslLineMCMConfProfileMaxTxPSDTable 1:(0..1)
                 ----> vdslLineMCMConfProfileMaxRxPSDTable 1:(0..1)

                   Figure 1: Table Relationships

     When the vdslLineCoding is set to MCM, the vdslLineConfProfileName
     which is the index of the vdslLineConfProfileEntry is also used as
     the index to the vdslLineMCMConfProfileTxBandTable of the
     vdslMCMGroup. The existence of an entry in any of the tables of
     the vdslMCMGroup is optional. Either none, some or all of the
     vdslMCMGroup tables MAY be implemented for a particular VDSL line
     entity using MCM line coding.

2.4  Persistence

   All read-write and read-create objects defined in this MIB module
   SHOULD be stored persistently.  Following is an exhaustive list of
   these persistent objects:

        vdslMCMConfProfileTxWindowLength
        vdslMCMConfProfileRowStatus
        vdslMCMConfProfileTxBandNumber
        vdslMCMConfProfileTxBandStart
        vdslMCMConfProfileTxBandStop
        vdslMCMConfProfileTxBandRowStatus
        vdslMCMConfProfileRxBandStart
        vdslMCMConfProfileRxBandStop
        vdslMCMConfProfileRxBandRowStatus
        vdslMCMConfProfileTxPSDTone
        vdslMCMConfProfileTxPSDPSD
        vdslMCMConfProfileTxPSDRowStatus
        vdslMCMConfProfileMaxTxPSDTone
        vdslMCMConfProfileMaxTxPSDPSD
        vdslMCMConfProfileMaxTxPSDRowStatus
        vdslMCMConfProfileMaxRxPSDTone
        vdslMCMConfProfileMaxRxPSDPSD
        vdslMCMConfProfileMaxRxPSDRowStatus

   It SHOULD also be noted that interface indices in this MIB are
   maintained persistently.  VACM data relating to these SHOULD be
   stored persistently as well [RFC2575].

3.  Conformance and Compliance

    For MCM VDSL lines, the following group is optional:

      -  vdslMCMGroup
4.  Definitions

        VDSL-LINE-EXT-MCM MIB DEFINITIONS ::= BEGIN

    IMPORTS

    MODULE-IDENTITY,
    OBJECT-TYPE,
    Counter64,
    Gauge32,
    Integer32,
    Unsigned32,
    NOTIFICATION-TYPE,
    transmission                    FROM SNMPv2-SMI
    TEXTUAL-CONVENTION,
    RowStatus,
    TruthValue                      FROM SNMPv2-TC
    HCPerfValidIntervals,
    HCPerfInvalidIntervals,
    HCPerfTimeElapsed,
    HCPerfIntervalThreshold,
    HCPerfCurrentCount,
    HCPerfIntervalCount             FROM HC-PerfHist-TC-MIB
    MODULE-COMPLIANCE,
    OBJECT-GROUP,
    NOTIFICATION-GROUP              FROM SNMPv2-CONF
    ifIndex                         FROM IF-MIB
    SnmpAdminString                 FROM SNMP-FRAMEWORK-MIB; SNMP-FRAMEWORK-MIB
    vdslLineConfProfileName         FROM VDSL-LINE-MIB VDSL-LINE-MIB;

    vdslExtMCMMIB MODULE-IDENTITY
       LAST-UPDATED "200309230000Z" "200402120000Z" -- September 23, 2003 February 12, 2004
       ORGANIZATION "ADSLMIB Working Group"
       CONTACT-INFO "WG-email:  adslmib@ietf.org
             Info:      https://www1.ietf.org/mailman/listinfo/adslmib

             Chair:     Mike Sneed
                        Sand Channel Systems
             Postal:    P.O. Box 37324
                        Raleigh NC 27627-732
             Email:     sneedmike@hotmail.com
             Phone:     +1 206 600 7022
             co-editor: Menachem Dodge
                        Infineon Technologies Savan Ltd.
                        6 Hagavish St.
              Postal:   Poleg Industrial Area,
                        Netanya 42504,
                        Israel.
              Email:    menachem.dodge@infineon.com
              Phone:    +972 9 892 4116

              Co-editor: Bob Ray
                         PESA Switching Systems, Inc.
              Postal:    330-A Wynn Drive
                         Huntsville, AL 35805
                         USA
              Email:     rray@pesa.com
              Phone:     +1 256 726 9200 ext.  142
            "
    DESCRIPTION
	    "The VDSL Line core MIB found in RFC XXXX defines objects for
    	the management of a pair of VDSL transceivers at each end of
        the VDSL line.  The core MIB configures and monitors the line
        code independent parameters (TC layer) of the VDSL line.
    	This MIB module is an optional extension of the core MIB and
        defines objects for configuration and monitoring of the line
        code specific (LCS) elements (PMD layer) for VDSL lines using
        MCM coding.  The objects in this extension MIB MUST NOT be used
        for VDSL lines using SCM line coding.

        Naming Conventions:
            Vtuc -- (VTUC) transceiver at near (Central) end of line
            Vtur -- (VTUR) transceiver at Remote end of line
            Vtu  -- One of either Vtuc or Vtur
            Curr -- Current
            Prev -- Previous
            Atn  -- Attenuation
            ES   -- Errored Second.
            SES  -- Severely Errored Second
            UAS  -- Unavailable Second
            LCS  -- Line Code Specific
            Lof  -- Loss of Frame
            Lol  -- Loss of Link
            Los  -- Loss of Signal
            Lpr  -- Loss of Power
            xxxs -- Interval of Seconds in which xxx occurs
                    (e.g., xxx=Lof, Los, Lpr)
            Max  -- Maximum
            Mgn  -- Margin
            Min  -- Minimum
            Psd  -- Power Spectral Density
            Snr  -- Signal to Noise Ratio
            Tx   -- Transmit
            Blks -- Blocks
     "
       Copyright (C) The Internet Society (2004).  This version
        of this MIB module is part of RFC XXXX: see the RFC
        itself for full legal notices."
-- RFC Ed.: replace XXXX with assigned number & remove this note
        REVISION "200402120000Z" -- February 12, 2004
        DESCRIPTION "Initial version, published as RFC XXXX."
-- RFC Ed.: replace XXXX with assigned number & remove this note
    ::= { vdslMIB XX }   -- To be assigned by IANA
-- RFC Ed.: we suggest to put it under { vdslMIB 3 } because
--          vdslMIB 1 is the VDSL core MIB, vdslMIB 2 is the SCM
--          extension MIB, while vdslMIB 3 is the MCM extension MIB.

   vdslLineExtMCMMib    OBJECT IDENTIFIER ::= { vdslEXTMCMMIB vdslExtMCMMIB 1 }
    vdslEXTMCMMibObjects
   vdslLineExtMCMMibObjects OBJECT IDENTIFIER ::= { vdslLineExtMCMMib 1 } {vdslLineExtMCMMib 1}

    --
    -- Multiple carrier modulation (MCM) configuration profile tables
    --

    vdslLineMCMConfProfileTable OBJECT-TYPE
        SYNTAX       SEQUENCE OF VdslLineMCMConfProfileEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "This table contains additional information on
            multiple carrier VDSL lines.  One entry in this table
            reflects a profile defined by a manager which can be used
            to configure the VDSL line.

            The entries in this table MUST NOT be used for single
            carrier (SCM) VDSL lines."
        ::= { vdslEXTMCMMibObjects vdslLineExtMCMMibObjects  1 }

    vdslLineMCMConfProfileEntry OBJECT-TYPE
        SYNTAX       VdslLineMCMConfProfileEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "Each entry consists of a list of parameters that
            represents the configuration of a multiple carrier
            modulation VDSL modem.

            A default profile with an index of 'DEFVAL', will always
            exist and its parameters will be set to vendor specific
            values, unless otherwise specified in this document."
        INDEX { vdslLineConfProfileName }
        ::= { vdslLineMCMConfProfileTable 1 }

    VdslLineMCMConfProfileEntry ::=
        SEQUENCE
            {
            vdslMCMConfProfileTxWindowLength
            vdslLineMCMConfProfileTxWindowLength       Unsigned32,
            vdslMCMConfProfileRowStatus
            vdslLineMCMConfProfileRowStatus            RowStatus
            }

    vdslMCMConfProfileTxWindowLength
    vdslLineMCMConfProfileTxWindowLength OBJECT-TYPE
        SYNTAX       Unsigned32 (1..255)
        UNITS        "samples"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the length of the transmit window, counted
            in samples at the sampling rate corresponding to the
            negotiated value of N."
        REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
        ::= { vdslLineMCMConfProfileEntry 1 }
    vdslMCMConfProfileRowStatus

    vdslLineMCMConfProfileRowStatus OBJECT-TYPE
        SYNTAX       RowStatus
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This object is used to create a new row or modify or
            delete an existing row in this table.

            A profile activated by setting this object to `active'.
            When `active' is set, the system will validate the profile.

            Before a profile can be deleted or taken out of
            service, (by setting this object to `destroy' or
            `outOfService') it must be first unreferenced
            from all associated lines."
        ::= { vdslLineMCMConfProfileEntry 2 }

    vdslLineMCMConfProfileTxBandTable OBJECT-TYPE
        SYNTAX       SEQUENCE OF VdslLineMCMConfProfileTxBandEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "This table contains transmit band descriptor configuration
            information for a VDSL line.  Each entry in this table
            reflects the configuration for one of possibly many bands
            with a multiple carrier modulation (MCM) VDSL line.
            These entries are defined by a manager and can be used to
            configure the VDSL line.

            The entries in this table MUST NOT be used for single
            carrier (SCM) VDSL lines."
        ::= { vdslEXTMCMMibObjects vdslLineExtMCMMibObjects  2 }
    vdslLineMCMConfProfileTxBandEntry OBJECT-TYPE
        SYNTAX       VdslLineMCMConfProfileTxBandEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "Each entry consists of a transmit band descriptor, which
            is defined by a start and a stop tone index.
            A default profile with an index of 'DEFVAL', will
            always exist and its parameters will be set to vendor
            specific values, unless otherwise specified in this
            document."
        INDEX { vdslLineConfProfileName,
                vdslMCMConfProfileTxBandNumber
                vdslLineMCMConfProfileTxBandNumber }
        ::= { vdslLineMCMConfProfileTxBandTable 1 }

    VdslLineMCMConfProfileTxBandEntry ::=
        SEQUENCE
            {
            vdslMCMConfProfileTxBandNumber
            vdslLineMCMConfProfileTxBandNumber           Unsigned32,
            vdslMCMConfProfileTxBandStart
            vdslLineMCMConfProfileTxBandStart            Unsigned32,
            vdslMCMConfProfileTxBandStop
            vdslLineMCMConfProfileTxBandStop             Unsigned32,
            vdslMCMConfProfileTxBandRowStatus
            vdslLineMCMConfProfileTxBandRowStatus        RowStatus
            }

    vdslMCMConfProfileTxBandNumber

    vdslLineMCMConfProfileTxBandNumber OBJECT-TYPE
        SYNTAX       Unsigned32
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "The index for this band descriptor entry."
        ::= { vdslLineMCMConfProfileTxBandEntry 1 }

    vdslMCMConfProfileTxBandStart

    vdslLineMCMConfProfileTxBandStart OBJECT-TYPE
        SYNTAX       Unsigned32
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Start tone index for this band."
        REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
        ::= { vdslLineMCMConfProfileTxBandEntry 2 }

    vdslMCMConfProfileTxBandStop

    vdslLineMCMConfProfileTxBandStop OBJECT-TYPE
        SYNTAX       Unsigned32
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Stop tone index for this band."
        REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
        ::= { vdslLineMCMConfProfileTxBandEntry 3 }

    vdslMCMConfProfileTxBandRowStatus
    vdslLineMCMConfProfileTxBandRowStatus OBJECT-TYPE
        SYNTAX       RowStatus
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This object is used to create a new row or modify or
            delete an existing row in this table.
            A profile activated by setting this object to `active'.
            When `active' is set, the system will validate the profile.

            Before a profile can be deleted or taken out of
            service, (by setting this object to `destroy' or
            `outOfService') it must be first unreferenced
            from all associated lines."
        ::= { vdslLineMCMConfProfileTxBandEntry 4 }

    vdslLineMCMConfProfileRxBandTable OBJECT-TYPE
        SYNTAX       SEQUENCE OF VdslLineMCMConfProfileRxBandEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "This table contains receive band descriptor configuration
            information for a VDSL line.  Each entry in this table
            reflects the configuration for one of possibly many bands
            with a multiple carrier modulation (MCM) VDSL line.
            These entries are defined by a manager and can be used to
            configure the VDSL line.

            The entries in this table MUST NOT be used for single
            carrier (SCM) VDSL lines."
        ::= { vdslEXTMCMMibObjects vdslLineExtMCMMibObjects 3 }

    vdslLineMCMConfProfileRxBandEntry OBJECT-TYPE
        SYNTAX       VdslLineMCMConfProfileRxBandEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "Each entry consists of a transmit band descriptor, which
            is defined by a start and a stop tone index.

            A default profile with an index of 'DEFVAL', will
            always exist and its parameters will be set to vendor
            specific values, unless otherwise specified in this
            document."
        INDEX { vdslLineConfProfileName,
                vdslMCMConfProfileRxBandNumber
                vdslLineMCMConfProfileRxBandNumber }
        ::= { vdslLineMCMConfProfileRxBandTable 1 }
    VdslLineMCMConfProfileRxBandEntry ::=
        SEQUENCE
            {
            vdslMCMConfProfileRxBandNumber
            vdslLineMCMConfProfileRxBandNumber           Unsigned32,
            vdslMCMConfProfileRxBandStart
            vdslLineMCMConfProfileRxBandStart            Unsigned32,
            vdslMCMConfProfileRxBandStop
            vdslLineMCMConfProfileRxBandStop             Unsigned32,
            vdslMCMConfProfileRxBandRowStatus
            vdslLineMCMConfProfileRxBandRowStatus        RowStatus
            }

    vdslMCMConfProfileRxBandNumber

    vdslLineMCMConfProfileRxBandNumber OBJECT-TYPE
        SYNTAX       Unsigned32
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "The index for this band descriptor entry."
        ::= { vdslLineMCMConfProfileRxBandEntry 1 }
    vdslMCMConfProfileRxBandStart

    vdslLineMCMConfProfileRxBandStart OBJECT-TYPE
        SYNTAX       Unsigned32
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Start tone index for this band."
        REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
        ::= { vdslLineMCMConfProfileRxBandEntry 2 }

    vdslMCMConfProfileRxBandStop

    vdslLineMCMConfProfileRxBandStop OBJECT-TYPE
        SYNTAX       Unsigned32
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Stop tone index for this band."
        REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
        ::= { vdslLineMCMConfProfileRxBandEntry 3 }

    vdslMCMConfProfileRxBandRowStatus

    vdslLineMCMConfProfileRxBandRowStatus OBJECT-TYPE
        SYNTAX       RowStatus
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This object is used to create a new row or modify or
            delete an existing row in this table.

            A profile activated by setting this object to `active'.
            When `active' is set, the system will validate the profile.

            Before a profile can be deleted or taken out of
            service, (by setting this object to `destroy' or
            `outOfService') it must be first unreferenced
            from all associated lines."
        ::= { vdslLineMCMConfProfileRxBandEntry 4 }
    vdslLineMCMConfProfileTxPSDTable OBJECT-TYPE
        SYNTAX       SEQUENCE OF VdslLineMCMConfProfileTxPSDEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "This table contains transmit PSD mask descriptor
            configuration information for a VDSL line.  Each entry in
            this table reflects the configuration for one tone within
            a multiple carrier modulation (MCM) VDSL line.  These
            entries are defined by a manager and can be used to
            configure the VDSL line.

            The entries in this table MUST NOT be used for single
            carrier (SCM) VDSL lines."
        ::= { vdslEXTMCMMibObjects vdslLineExtMCMMibObjects 4 }

    vdslLineMCMConfProfileTxPSDEntry OBJECT-TYPE
        SYNTAX       VdslLineMCMConfProfileTxPSDEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "Each entry consists of a transmit PSD mask descriptor,
            which defines the power spectral density (PSD) for a tone.

            A default profile with an index of 'DEFVAL', will
            always exist and its parameters will be set to vendor
            specific values, unless otherwise specified in this
            document."
        INDEX { vdslLineConfProfileName,
                vdslMCMConfProfileTxPSDNumber
                vdslLineMCMConfProfileTxPSDNumber }
        ::= { vdslLineMCMConfProfileTxPSDTable 1 }

    VdslLineMCMConfProfileTxPSDEntry ::=
        SEQUENCE
            {
            vdslMCMConfProfileTxPSDNumber
            vdslLineMCMConfProfileTxPSDNumber            Unsigned32,
            vdslMCMConfProfileTxPSDTone
            vdslLineMCMConfProfileTxPSDTone              Unsigned32,
            vdslMCMConfProfileTxPSDPSD
            vdslLineMCMConfProfileTxPSDPSD               Unsigned32,
            vdslMCMConfProfileTxPSDRowStatus
            vdslLineMCMConfProfileTxPSDRowStatus         RowStatus
            }

    vdslMCMConfProfileTxPSDNumber

    vdslLineMCMConfProfileTxPSDNumber OBJECT-TYPE
        SYNTAX       Unsigned32
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "The index for this mask descriptor entry."
        ::= { vdslLineMCMConfProfileTxPSDEntry 1 }

    vdslMCMConfProfileTxPSDTone
    vdslLineMCMConfProfileTxPSDTone OBJECT-TYPE
        SYNTAX       Unsigned32
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "The tone index for which the PSD is being specified."
        REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
        ::= { vdslLineMCMConfProfileTxPSDEntry 2 }

    vdslMCMConfProfileTxPSDPSD

    vdslLineMCMConfProfileTxPSDPSD OBJECT-TYPE
        SYNTAX       Unsigned32
        UNITS        "0.5dBm"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Power Spectral Density level in steps of 0.5dB with
            an offset of -140dbm/Hz."
        REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
        ::= { vdslLineMCMConfProfileTxPSDEntry 3 }
    vdslMCMConfProfileTxPSDRowStatus

    vdslLineMCMConfProfileTxPSDRowStatus OBJECT-TYPE
        SYNTAX       RowStatus
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This object is used to create a new row or modify or
            delete an existing row in this table.

            A profile activated by setting this object to `active'.
            When `active' is set, the system will validate the profile.

            Before a profile can be deleted or taken out of
            service, (by setting this object to `destroy' or
            `outOfService') it must be first unreferenced
            from all associated lines."
        ::= { vdslLineMCMConfProfileTxPSDEntry 4 }

    vdslLineMCMConfProfileMaxTxPSDTable OBJECT-TYPE
        SYNTAX       SEQUENCE OF VdslLineMCMConfProfileMaxTxPSDEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "This table contains transmit maximum PSD mask descriptor
            configuration information for a VDSL line.  Each entry in
            this table reflects the configuration for one tone within
            a multiple carrier modulation (MCM) VDSL modem.  These
            entries are defined by a manager and can be used to
            configure the VDSL line.

            The entries in this table MUST NOT be used for single
            carrier (SCM) VDSL lines."
        ::= { vdslEXTMCMMibObjects vdslLineExtMCMMibObjects 5 }
    vdslLineMCMConfProfileMaxTxPSDEntry OBJECT-TYPE
        SYNTAX       VdslLineMCMConfProfileMaxTxPSDEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "Each entry consists of a transmit PSD mask descriptor,
            which defines the maximum power spectral density (PSD)
            for a tone.

            A default profile with an index of 'DEFVAL', will
            always exist and its parameters will be set to vendor
            specific values, unless otherwise specified in this
            document."
        INDEX { vdslLineConfProfileName,
                vdslMCMConfProfileMaxTxPSDNumber
                vdslLineMCMConfProfileMaxTxPSDNumber }
        ::= { vdslLineMCMConfProfileMaxTxPSDTable 1 }

    VdslLineMCMConfProfileMaxTxPSDEntry ::=
        SEQUENCE
            {
            vdslMCMConfProfileMaxTxPSDNumber
            vdslLineMCMConfProfileMaxTxPSDNumber            Unsigned32,
            vdslMCMConfProfileMaxTxPSDTone
            vdslLineMCMConfProfileMaxTxPSDTone              Unsigned32,
            vdslMCMConfProfileMaxTxPSDPSD
            vdslLineMCMConfProfileMaxTxPSDPSD               Unsigned32,
            vdslMCMConfProfileMaxTxPSDRowStatus
            vdslLineMCMConfProfileMaxTxPSDRowStatus         RowStatus
            }

    vdslMCMConfProfileMaxTxPSDNumber

    vdslLineMCMConfProfileMaxTxPSDNumber OBJECT-TYPE
        SYNTAX       Unsigned32
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "The index for this band descriptor entry."
        ::= { vdslLineMCMConfProfileMaxTxPSDEntry 1 }

    vdslMCMConfProfileMaxTxPSDTone

    vdslLineMCMConfProfileMaxTxPSDTone OBJECT-TYPE
        SYNTAX       Unsigned32
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "The tone index for which the PSD is being specified."
        REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
        ::= { vdslLineMCMConfProfileMaxTxPSDEntry 2 }

    vdslMCMConfProfileMaxTxPSDPSD
    vdslLineMCMConfProfileMaxTxPSDPSD OBJECT-TYPE
        SYNTAX       Unsigned32
        UNITS        "0.5dBm"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Power Spectral Density level in steps of 0.5dB with
            an offset of -140dbm/Hz."
        REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
        ::= { vdslLineMCMConfProfileMaxTxPSDEntry 3 }

    vdslMCMConfProfileMaxTxPSDRowStatus

    vdslLineMCMConfProfileMaxTxPSDRowStatus OBJECT-TYPE
        SYNTAX       RowStatus
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This object is used to create a new row or modify or
            delete an existing row in this table.

            A profile activated by setting this object to `active'.
            When `active' is set, the system will validate the profile.

            Before a profile can be deleted or taken out of
            service, (by setting this object to `destroy' or
            `outOfService') it must be first unreferenced
            from all associated lines."
        ::= { vdslLineMCMConfProfileMaxTxPSDEntry 4 }

    vdslLineMCMConfProfileMaxRxPSDTable OBJECT-TYPE
        SYNTAX       SEQUENCE OF VdslLineMCMConfProfileMaxRxPSDEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "This table contains maximum receive PSD mask descriptor
            configuration information for a VDSL line.  Each entry in
            this table reflects the configuration for one tone within
            a multiple carrier modulation (MCM) VDSL modem.  These
            entries are defined by a manager and can be used to
            configure the VDSL line.

            The entries in this table MUST NOT be used for single
            carrier (SCM) VDSL lines."
        ::= { vdslEXTMCMMibObjects vdslLineExtMCMMibObjects 6 }
    vdslLineMCMConfProfileMaxRxPSDEntry OBJECT-TYPE
        SYNTAX       VdslLineMCMConfProfileMaxRxPSDEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "Each entry consists of a transmit PSD mask descriptor,
            which defines the power spectral density (PSD) for a
            tone.

            A default profile with an index of 'DEFVAL', will
            always exist and its parameters will be set to vendor
            specific values, unless otherwise specified in this
            document."
        INDEX { vdslLineConfProfileName,
                vdslMCMConfProfileMaxRxPSDNumber
                vdslLineMCMConfProfileMaxRxPSDNumber }
        ::= { vdslLineMCMConfProfileMaxRxPSDTable 1 }

    VdslLineMCMConfProfileMaxRxPSDEntry ::=
        SEQUENCE
            {
            vdslMCMConfProfileMaxRxPSDNumber
            vdslLineMCMConfProfileMaxRxPSDNumber            Unsigned32,
            vdslMCMConfProfileMaxRxPSDTone
            vdslLineMCMConfProfileMaxRxPSDTone              Unsigned32,
            vdslMCMConfProfileMaxRxPSDPSD
            vdslLineMCMConfProfileMaxRxPSDPSD               Unsigned32,
            vdslMCMConfProfileMaxRxPSDRowStatus
            vdslLineMCMConfProfileMaxRxPSDRowStatus         RowStatus
            }

    vdslMCMConfProfileMaxRxPSDNumber

    vdslLineMCMConfProfileMaxRxPSDNumber OBJECT-TYPE
        SYNTAX       Unsigned32
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "The index for this band descriptor entry."
        ::= { vdslLineMCMConfProfileMaxRxPSDEntry 1 }
    vdslMCMConfProfileMaxRxPSDTone

    vdslLineMCMConfProfileMaxRxPSDTone OBJECT-TYPE
        SYNTAX       Unsigned32
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "The tone index for which the PSD is being specified."
        REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
        ::= { vdslLineMCMConfProfileMaxRxPSDEntry 2 }

    vdslMCMConfProfileMaxRxPSDPSD
    vdslLineMCMConfProfileMaxRxPSDPSD OBJECT-TYPE
        SYNTAX       Unsigned32
        UNITS        "0.5dBm"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Power Spectral Density level in steps of 0.5dB with
            an offset of -140dbm/Hz."
        REFERENCE    "T1E1.4/2000-013R4"    -- Part 3, MCM
        ::= { vdslLineMCMConfProfileMaxRxPSDEntry 3 }

    vdslMCMConfProfileMaxRxPSDRowStatus

    vdslLineMCMConfProfileMaxRxPSDRowStatus OBJECT-TYPE
        SYNTAX       RowStatus
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This object is used to create a new row or modify or
            delete an existing row in this table.

            A profile activated by setting this object to `active'.
            When `active' is set, the system will validate the profile.

            Before a profile can be deleted or taken out of
            service, (by setting this object to `destroy' or
            `outOfService') it must be first unreferenced
            from all associated lines."
        ::= { vdslLineMCMConfProfileMaxRxPSDEntry 4 }

     -- conformance information

    vdslExtMCMConformance

    vdslLineExtMCMConformance OBJECT IDENTIFIER ::= { vdslLineExtMCMMib 2 }
    vdslExtMCMGroups
						{vdslLineExtMCMMib 2}
    vdslLineExtMCMGroups OBJECT IDENTIFIER ::=
 					{ vdslExtMCMConformance vdslLineExtMCMConformance 1 }
    vdslExtMCMCompliances
    vdslLineExtMCMCompliances OBJECT IDENTIFIER ::=
                                        { vdslExtMCMConformance vdslLineExtMCMConformance 2 }

    vdslLineExtMCMMibCompliance MODULE-COMPLIANCE
        STATUS  current
        DESCRIPTION
            "The compliance statement for SNMP entities which
            manage VDSL interfaces."

        MODULE  -- this module
        GROUP       vdslMCMGroup       vdslLineExtMCMGroup
        DESCRIPTION
            "This group is an optional extension for VDSL lines which
            utilize Multiple Carrier Modulation (MCM)."

        ::= { vdslCompliances vdslLineExtMCMCompliances 1 }

    -- units of conformance

        vdslMCMGroup

        vdslLineExtMCMGroup OBJECT-GROUP
             OBJECTS
                {
                vdslMCMConfProfileTxWindowLength,
                vdslMCMConfProfileRowStatus,
                vdslMCMConfProfileTxBandStart,
                vdslMCMConfProfileTxBandStop,
                vdslMCMConfProfileTxBandRowStatus,
                vdslMCMConfProfileRxBandStart,
                vdslMCMConfProfileRxBandStop,
                vdslMCMConfProfileRxBandRowStatus,
                vdslMCMConfProfileTxPSDTone,
                vdslMCMConfProfileTxPSDPSD,
                vdslMCMConfProfileTxPSDRowStatus,
                vdslMCMConfProfileMaxTxPSDTone,
                vdslMCMConfProfileMaxTxPSDPSD,
                vdslMCMConfProfileMaxTxPSDRowStatus,
                vdslMCMConfProfileMaxRxPSDTone,
                vdslMCMConfProfileMaxRxPSDPSD,
                vdslMCMConfProfileMaxRxPSDRowStatus
                vdslLineMCMConfProfileTxWindowLength,
                vdslLineMCMConfProfileRowStatus,
                vdslLineMCMConfProfileTxBandStart,
                vdslLineMCMConfProfileTxBandStop,
                vdslLineMCMConfProfileTxBandRowStatus,
                vdslLineMCMConfProfileRxBandStart,
                vdslLineMCMConfProfileRxBandStop,
                vdslLineMCMConfProfileRxBandRowStatus,
                vdslLineMCMConfProfileTxPSDTone,
                vdslLineMCMConfProfileTxPSDPSD,
                vdslLineMCMConfProfileTxPSDRowStatus,
                vdslLineMCMConfProfileMaxTxPSDTone,
                vdslLineMCMConfProfileMaxTxPSDPSD,
                vdslLineMCMConfProfileMaxTxPSDRowStatus,
                vdslLineMCMConfProfileMaxRxPSDTone,
                vdslLineMCMConfProfileMaxRxPSDPSD,
                vdslLineMCMConfProfileMaxRxPSDRowStatus
                }
             STATUS     current
             DESCRIPTION
                 "A collection of objects providing configuration
                 information for a VDSL line based upon multiple
                 carrier modulation modem."
         ::= { vdslGroups vdslLineExtMCMGroup 1 }

    END

5.  Intellectual Property Notice

   The IETF takes no position regarding the validity or scope of any
   intellectual property or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available;  neither does it represent that it
   has made any effort to identify any such rights.  Information on the
   IETF's procedures with respect to rights in standards-track and
   standards-related documentation can be found in BCP-11.  Copies of
   claims of rights made available for publication and any assurances
   of licenses to be made available, or the result of an attempt made
   to obtain a general license or permission for the use of such
   proprietary rights by implementors or users of this specification
   can be obtained from the IETF Secretariat.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights which may cover technology that may be required to practice
   this standard.  Please address the information to the IETF Executive
   Director.

6. Normative References

   [DSLFTR057] DSL Forum TR-057, "VDSL Network Element Management",
               February 2003.

   [ETSI2701] ETSI TS 101 270-1 V1.2.1 "Transmission and Multiplexing
              (TM); Access transmission systems on metallic access
              cables; Very high speed Digital Subscriber Line (VDSL);
              Part 1: Functional requirements", October 1999.

   [ETSI2702] ETSI TS 101 270-2 V1.1.1 "Transmission and Multiplexing
              (TM); Access transmission systems on metallic access
              cables; Very high speed Digital Subscriber Line (VDSL);
              Part 1: Transceiver specification", February 2001.

   [ITU9931]  ITU-T G.993.1 "Very-high-speed digital subscriber line
              foundation", November 2001.

   [ITU9971]  ITU-T G.997.1 "Physical layer management for Digital
              Subscriber Line (DSL) Transceivers", July 1999.

   [RFC2493]  Tesink, K., "Textual Conventions

   [RFC2119]   Bradner, S., "Key words for MIB Modules Using
              Performance History Based on 15 Minute Intervals", use in RFCs to Indicate
               Requirement Levels", BCP 14, RFC
              2493, January 1999. 2119, March 1997.

   [RFC2578]   McCloghrie, K., Perkins, D., Schoenwaelder, J., Case,
               J., Rose, M.  and S.  Waldbusser, "Structure of
               Management Information Version 2 (SMIv2)", STD 58, RFC
               2578, April 1999.

   [RFC2579]   McCloghrie, K., Perkins, D., Schoenwaelder, J., Case,
               J., Rose, M.  and S.  Waldbusser, "Textual Conventions
               for SMIv2", STD 58, RFC 2579, April 1999.

   [RFC2580]   McCloghrie, K., Perkins, D., Schoenwaelder, J., Case,
               J., Rose, M.  and S.  Waldbusser, "Conformance
               Statements for SMIv2", STD 58, RFC 2580, April 1999.

   [RFC2863]   McCloghrie, K.  and F.  Kastenholz, "The Interfaces
               Group MIB", RFC 2863, June 2000.

   [RFC3418]   Presuhn, R., "Management Information Base (MIB) for the
               Simple Network Management Protocol (SNMP)", STD 62, RFC
               3418, December 2002.

   [RFCXXXX] Ray, B. and R. Abbi, "Definitions of Managed Objects

   [RFC3593]   Tesink, K., "Textual Conventions for
             Very High Speed Digital Subscriber Lines (VDSL)", MIB Modules Using
               Performance History Based on 15 Minute Intervals", RFC XXXX,
             YYYY
               3593, September 2003.

   [RFCXXXX]   Ray, B. and R. Abbi, "High Capacity Textual Conventions
               for MIB Modules Using Performance History Based on
               15 Minute Intervals", RFC XXXX, YYYY 2003.

   [RFCXXXX] Ray, B. and R. Abbi, "Definitions of Managed Objects for
             Very High Speed Digital Subscriber Lines (VDSL)",RFC XXXX,
             YYYY 2003.

   [T1E1311]   ANSI T1E1.4/2001-311, "Very-high-bit-rate Digital
               Subscriber Line (VDSL) Metallic Interface, Part 1:
               Functional Requirements and Common Specification",
               February 2001.

   [T1E1011]   ANSI T1E1.4/2001-011R3, "VDSL Metallic Interface, Part
               2: Technical Specification for a Single-Carrier
               Modulation (SCM) Transceiver", November 2001.

   [T1E1013]   ANSI T1E1.4/2001-013R4, "VDSL Metallic Interface, Part
               3: Technical Specification for a Multi-Carrier
               Modulation (MCM) Transceiver", November 2000.

7.  Informative References

   [RFC2575]  Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based
              Access Control Model (VACM) for the Simple Network
              Management Protocol (SNMP)", RFC 2575, April 1999.

   [RFC3410] Case, J., Mundy, R., Partain, D.  and B.  Stewart,
             "Introduction and Applicability Statements for Internet-
             Standard Management Framework", RFC 3410, December 2002.

8.  Security Considerations

   There are a number of management objects defined in this MIB that
   have a MAX-ACCESS clause of read-write and/or read-create.  Such
   objects may be considered sensitive or vulnerable in some network
   environments.  The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on
   network operations.

   VDSL layer connectivity from the Vtur will permit the subscriber
   to manipulate both the VDSL link directly and the VDSL embedded
   operations channel (EOC) for their own loop. For example, unchecked
   or unfiltered fluctuations initiated by the subscriber could
   generate sufficient notifications to potentially overwhelm either
   the management interface to the network or the element manager.

   For this reason, there are a number of managed objects in this MIB
   that may contain sensitive information.

   It is thus important to control even GET access to these objects and
   possibly to even encrypt the values of these objects when sending
   them over the network via SNMP.  Not all versions of SNMP provide
   features for such a secure environment.

   Further, notifications generated by agents implementing this MIB
   will contain the above threshold information.

   SNMP versions prior to SNMPv3 did not include adequate security.
   Even if the network itself is secure (for example by using IPSec),
   even then, there is no control as to who on the secure network is
   allowed to access and GET/SET (read/change/create/delete) objects
   which utilize the textual conventions defined in this MIB module.

   It is RECOMMENDED that implementers consider the security features
   as provided by the SNMPv3 framework (see [RFC3410], section 8),
   including full support for the SNMPv3 cryptographic mechanisms (for
   authentication and privacy).

   Further, deployment of SNMP versions prior to SNMPv3 is NOT
   RECOMMENDED.  Instead, it is RECOMMENDED to deploy SNMPv3 and to
   enable cryptographic security.  It is then a customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of a MIB module which utilizes the textual conventions
   defined in this MIB module is properly configured to give access to
   the objects only to those principals (users) that have legitimate
   rights to indeed GET or SET (change/create/delete) them.

9.  Acknowledgments

    This document contains many definitions taken from
    draft-ietf-adslmib-vdsl-07.txt. As such such, any credit for the text
    found within should be full fully attributed to the authors of that
    document.

10.  Authors' Addresses

   Menachem Dodge
   Infineon Technologies Savan Ltd.
   6 Hagavish St.
   Poleg Industrial Area,
   Netanya 42504,
   Israel.

   Phone: +972 9 892 4116
   Fax: +972 9 865 8756
   Email: menachem.dodge@infineon.com

   Bob Ray
   PESA Switching Systems, Inc.
   330-A Wynn Drive
   Huntsville, AL 35805
   USA

   Phone: +1 256 726 9200 ext.  142
   Fax: +1 256 726 9271
   EMail: rray@pesa.com

 11.  Full Copyright Statement

   Copyright (C) The Internet Society (2003).  All Rights Reserved.
   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph
   are included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.