draft-ietf-adslmib-vdsl-03.txt   draft-ietf-adslmib-vdsl-04.txt 
Network Working Group B. Ray Network Working Group B. Ray
Category: Internet Draft PESA Switching Systems Category: Internet Draft PESA Switching Systems
R. Abbi R. Abbi
Alcatel Alcatel
June 2002 September 2002
Definitions of Managed Objects for Very High Definitions of Managed Objects for Very High
Speed Digital Subscriber Lines (VDSL) Speed Digital Subscriber Lines (VDSL)
draft-ietf-adslmib-vdsl-03.txt draft-ietf-adslmib-vdsl-04.txt
Status of this Memo Status of this Memo
This document is an Internet-Draft and is subject to all provisions This document is an Internet-Draft and is subject to all provisions
of Section 10 of RFC2026. of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet- other groups may also distribute working documents as Internet-
Drafts. Drafts.
skipping to change at page 1, line 43 skipping to change at page 1, line 43
Copyright Notice Copyright Notice
Copyright (C) The Internet Society (2002). All Rights Reserved. Copyright (C) The Internet Society (2002). All Rights Reserved.
Abstract Abstract
This document defines a Management Information Base (MIB) module for This document defines a Management Information Base (MIB) module for
use with network management protocols in the Internet community. In use with network management protocols in the Internet community. In
particular, it describes objects used for managing Very high speed particular, it describes objects used for managing Very high speed
Digital Subscriber Line (VDSL) interfaces [T1E1311, T1E1011, T1E1013, Digital Subscriber Line (VDSL) interfaces [T1E1311, T1E1011, T1E1013,
ETSI2701, ETSI2702, ITU9931]. ETSI2701, ETSI2702, ITU9931, ITU9971].
This document specifies a MIB module in a manner that is compliant This document specifies a MIB module in a manner that is compliant
to the SMIv2 (STD 58 [RFC2578, RFC2579, RFC2580]). to the SMIv2 (STD 58 [RFC2578, RFC2579, RFC2580]).
Table of Contents Table of Contents
1. The SNMP Management Framework ............................. 2 1. The SNMP Management Framework ............................. 2
2. Overview .................................................. 3 2. Overview .................................................. 3
2.1 Relationship of the VDSL Line MIB to other MIBs ........... 3 2.1 Relationship of the VDSL Line MIB to other MIBs ........... 3
2.2 Conventions used in the MIB ............................... 5 2.2 Conventions used in the MIB ............................... 5
2.3 Structure ................................................. 6 2.3 Structure ................................................. 6
2.4 Counters, Interval Buckets and Thresholds ................. 8 2.4 Counters, Interval Buckets and Thresholds ................. 8
2.5 Profiles .................................................. 8 2.5 Profiles .................................................. 8
2.6 Notifications ............................................. 10 2.6 Notifications ............................................. 9
2.7 Persistence ............................................... 10 2.7 Persistence ............................................... 10
3. Conformance and Compliance ................................ 12 3. Conformance and Compliance ................................ 12
4. Definitions ............................................... 12 4. Definitions ............................................... 12
References ................................................ 66 References ................................................ 66
Security Considerations ................................... 68 Security Considerations ................................... 68
IANA Considerations ....................................... 69 IANA Considerations ....................................... 69
Acknowledgments ........................................... 69 Acknowledgments ........................................... 69
Intellectual Property Notice .............................. 69 Intellectual Property Notice .............................. 69
Authors' Addresses ........................................ 70 Authors' Addresses ........................................ 70
Full Copyright Statement .................................. 70 Full Copyright Statement .................................. 70
skipping to change at page 3, line 33 skipping to change at page 3, line 34
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in
this document are to be interpreted as described in RFC 2119 this document are to be interpreted as described in RFC 2119
[RFC2119]. [RFC2119].
2. Overview 2. Overview
This document describes an SNMP MIB for managing VDSL Lines. These This document describes an SNMP MIB for managing VDSL Lines. These
definitions are based upon the specifications for VDSL as defined definitions are based upon the specifications for VDSL as defined
in T1E1, ETSI, and ITU documentation [T1E1311, T1E1011, T1E1013, in T1E1, ETSI, and ITU documentation [T1E1311, T1E1011, T1E1013,
ETSI2701, ETSI2702, ITU9931]. ETSI2701, ETSI2702, ITU9931, ITU9971].
The MIB is located in the MIB tree under MIB 2 transmission, as The MIB is located in the MIB tree under MIB 2 transmission, as
discussed in the MIB-2 Integration (RFC 2863 [RFC2863]) section of discussed in the MIB-2 Integration (RFC 2863 [RFC2863]) section of
this document. this document.
2.1 Relationship of the VDSL Line MIB to other MIBs 2.1 Relationship of the VDSL Line MIB to other MIBs
This section outlines the relationship of this MIB with other MIBs This section outlines the relationship of this MIB with other MIBs
described in RFCs. Specifically, IF-MIB as presented RFC 2863 described in RFCs. Specifically, IF-MIB as presented RFC 2863
[RFC2863] is discussed. [RFC2863] is discussed.
skipping to change at line 494 skipping to change at page 10, line 38
Note that the Network Management System, or NMS, may receive a Note that the Network Management System, or NMS, may receive a
linkDown notification, as well, if enabled (via linkDown notification, as well, if enabled (via
ifLinkUpDownTrapEnable [RFC2863]). At the beginning of the next 15 minute ifLinkUpDownTrapEnable [RFC2863]). At the beginning of the next 15 minute
interval, the counter is reset. When the first second goes by and interval, the counter is reset. When the first second goes by and
the event occurs, the current interval bucket will be 1, which the event occurs, the current interval bucket will be 1, which
equals the threshold and the notification will be sent again. equals the threshold and the notification will be sent again.
2.7 Persistence 2.7 Persistence
Expires December 17, 2002 [PAGE 10]
All objects defined in this MIB which may be set (read-write or All objects defined in this MIB which may be set (read-write or
read-create), should be stored persistently. Following is an read-create), should be stored persistently. Following is an
exhaustive list of these persistent objects: exhaustive list of these persistent objects:
vdslLineConfProfile vdslLineConfProfile
vdslLineAlarmConfProfile vdslLineAlarmConfProfile
vdslLineConfProfileIndex vdslLineConfProfileIndex
vdslLineConfProfileName vdslLineConfProfileName
vdslLineConfTargetSnrMgn vdslLineConfDownstreamMaxPwr
vdslLineConfUpstreamTxSpeed vdslLineConfUpstreamMaxPwr
vdslLineConfDownstreamTxSpeed vdslLineConfDownstreamMaxSnrMgn
vdslLineConfDownstreamMinSnrMgn
vdslLineConfDownstreamTargetSnrMgn
vdslLineConfUpstreamMaxSnrMgn
vdslLineConfUpstreamMinSnrMgn
vdslLineConfUpstreamTargetSnrMgn
vdslLineConfDownstreamFastMaxDataRate
vdslLineConfDownstreamFastMinDataRate
vdslLineConfDownstreamSlowMaxDataRate
vdslLineConfDownstreamSlowMinDataRate
vdslLineConfUpstreamFastMaxDataRate
vdslLineConfUpstreamFastMinDataRate
vdslLineConfUpstreamSlowMaxDataRate
vdslLineConfUpstreamSlowMinDataRate
vdslLineConfRateAdaptationRatio
vdslLineConfUpstreamDataRate
vdslLineConfDownstreamDataRate
vdslLineConfDownstreamMaxInterDelay
vdslLineConfUpstreamMaxInterDelay
vdslLineConfUpstreamPboControl vdslLineConfUpstreamPboControl
vdslLineConfDownstreamPboControl vdslLineConfDownstreamPboControl
vdslLineConfDeploymentScenario vdslLineConfDeploymentScenario
vdslLineConfAdslOccupy vdslLineConfAdslOccupy
vdslLineConfApplicableStandard vdslLineConfApplicableStandard
vdslLineConfBandPlan vdslLineConfBandPlan
vdslLineConfBandPlanFx vdslLineConfBandPlanFx
vdslLineConfBandU0Usage vdslLineConfBandU0Usage
vdslLineConfUpstreamPsdTemplate vdslLineConfUpstreamPsdTemplate
vdslLineConfDownstreamPsdTemplate vdslLineConfDownstreamPsdTemplate
skipping to change at line 539 skipping to change at page 11, line 48
vdslMCMConfProfileTxPSDPSD vdslMCMConfProfileTxPSDPSD
vdslMCMConfProfileTxPSDRowStatus vdslMCMConfProfileTxPSDRowStatus
vdslMCMConfProfileMaxTxPSDNumber vdslMCMConfProfileMaxTxPSDNumber
vdslMCMConfProfileMaxTxPSDTone vdslMCMConfProfileMaxTxPSDTone
vdslMCMConfProfileMaxTxPSDPSD vdslMCMConfProfileMaxTxPSDPSD
vdslMCMConfProfileMaxTxPSDRowStatus vdslMCMConfProfileMaxTxPSDRowStatus
vdslMCMConfProfileMaxRxPSDNumber vdslMCMConfProfileMaxRxPSDNumber
vdslMCMConfProfileMaxRxPSDTone vdslMCMConfProfileMaxRxPSDTone
vdslMCMConfProfileMaxRxPSDPSD vdslMCMConfProfileMaxRxPSDPSD
vdslMCMConfProfileMaxRxPSDRowStatus vdslMCMConfProfileMaxRxPSDRowStatus
vdslSCMConfProfileInterleaveDepth vdslSCMConfProfileDownInterleaveDepth
vdslSCMConfProfileFastCodewordSize vdslSCMConfProfileUpInterleaveDepth
vdslSCMConfProfileDownNumCarriers
vdslSCMConfProfileUpNumCarriers
vdslSCMConfProfileDownFastCodewordSize
vdslSCMConfProfileUpFastCodewordSize
vdslSCMConfProfileTransmitPSDMask vdslSCMConfProfileTransmitPSDMask
vdslSCMConfProfileBands vdslSCMConfProfileVendorNotch1Start
vdslSCMConfProfileFastFecSize vdslSCMConfProfileVendorNotch1Stop
vdslSCMConfProfileVendorNotch2Start
vdslSCMConfProfileVendorNotch2Stop
vdslSCMConfProfileDownFastFecSize
vdslSCMConfProfileUpFastFecSize
vdslSCMConfProfileDownSlowBlockSize
vdslSCMConfProfileUpSlowBlockSize
vdslSCMConfProfileRowStatus vdslSCMConfProfileRowStatus
vdslSCMConfProfileTxBandNumber vdslSCMConfProfileTxBandNumber
vdslSCMConfProfileTxBandTransmitPSDLevel vdslSCMConfProfileTxBandTransmitPSDLevel
vdslSCMConfProfileTxBandSymbolRateProfile vdslSCMConfProfileTxBandSymbolRateProfile
Expires December 17, 2002 [PAGE 11]
vdslSCMConfProfileTxBandConstellationSize vdslSCMConfProfileTxBandConstellationSize
vdslSCMConfProfileTxBandCenterFrequency vdslSCMConfProfileTxBandCenterFrequency
vdslSCMConfProfileTxBandRowStatus vdslSCMConfProfileTxBandRowStatus
vdslLineAlarmConfProfileIndex vdslLineAlarmConfProfileIndex
vdslLineAlarmConfProfileName vdslLineAlarmConfProfileName
vdslThresh15MinLofs vdslThresh15MinLofs
vdslThresh15MinLoss vdslThresh15MinLoss
vdslThresh15MinLprs vdslThresh15MinLprs
vdslThresh15MinESs vdslThresh15MinESs
vdslThresh15MinSESs vdslThresh15MinSESs
skipping to change at line 599 skipping to change at page 13, line 12
OBJECT-TYPE, OBJECT-TYPE,
Counter64, Counter64,
Gauge32, Gauge32,
Integer32, Integer32,
Unsigned32, Unsigned32,
NOTIFICATION-TYPE, NOTIFICATION-TYPE,
transmission FROM SNMPv2-SMI transmission FROM SNMPv2-SMI
TEXTUAL-CONVENTION, TEXTUAL-CONVENTION,
RowStatus, RowStatus,
TruthValue FROM SNMPv2-TC TruthValue FROM SNMPv2-TC
HCPerfValidIntervals,
HCPerfInvalidIntervals,
HCPerfTimeElapsed,
HCPerfIntervalThreshold,
HCPerfCurrentCount, HCPerfCurrentCount,
HCPerfIntervalCount FROM HC-PerfHist-TC-MIB HCPerfIntervalCount FROM HC-PerfHist-TC-MIB
MODULE-COMPLIANCE, MODULE-COMPLIANCE,
OBJECT-GROUP, OBJECT-GROUP,
Expires December 17, 2002 [PAGE 12]
NOTIFICATION-GROUP FROM SNMPv2-CONF NOTIFICATION-GROUP FROM SNMPv2-CONF
ifIndex FROM IF-MIB ifIndex FROM IF-MIB
SnmpAdminString FROM SNMP-FRAMEWORK-MIB; SnmpAdminString FROM SNMP-FRAMEWORK-MIB;
vdslMIB MODULE-IDENTITY vdslMIB MODULE-IDENTITY
LAST-UPDATED "200204090000Z" -- April 9, 2002 LAST-UPDATED "200209230000Z" -- September 23, 2002
ORGANIZATION "ADSLMIB Working Group" ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO "WG-email: adslmib@ietf.org CONTACT-INFO "WG-email: adslmib@ietf.org
Info: https://www1.ietf.org/mailman/listinfo/adslmib Info: https://www1.ietf.org/mailman/listinfo/adslmib
Chair: Mike Sneed Chair: Mike Sneed
Postal: P.O. Box 37324 Postal: P.O. Box 37324
Raleigh NC 27627-7324 Raleigh NC 27627-7324
Email: sneedmike@hotmail.com Email: sneedmike@hotmail.com
Co-editor: Bob Ray Co-editor: Bob Ray
skipping to change at line 658 skipping to change at page 14, line 21
ifTable, one for each physical, fast, and interleaved, whose ifTable, one for each physical, fast, and interleaved, whose
ifType values are equal to vdsl(97), fast(125), and ifType values are equal to vdsl(97), fast(125), and
interleaved(124), respectively. The ifStackTable is used to interleaved(124), respectively. The ifStackTable is used to
represent the relationship between the entries. represent the relationship between the entries.
Naming Conventions: Naming Conventions:
Vtuc -- (VTUC) modem at near (Central) end of line Vtuc -- (VTUC) modem at near (Central) end of line
Vtur -- (VTUR) modem at Remote end of line Vtur -- (VTUR) modem at Remote end of line
Vtu -- One of either Vtuc or Vtur Vtu -- One of either Vtuc or Vtur
Curr -- Current Curr -- Current
Expires December 17, 2002 [PAGE 13]
Prev -- Previous Prev -- Previous
Atn -- Attenuation Atn -- Attenuation
ES -- Errored Second. ES -- Errored Second.
LCS -- Line Code Specific LCS -- Line Code Specific
Lof -- Loss of Frame Lof -- Loss of Frame
Lol -- Loss of Link Lol -- Loss of Link
Los -- Loss of Signal Los -- Loss of Signal
Lpr -- Loss of Power Lpr -- Loss of Power
xxxs -- interval of Seconds in which xxx occurs xxxs -- interval of Seconds in which xxx occurs
(e.g., xxx=Lof, Los, Lpr) (e.g., xxx=Lof, Los, Lpr)
skipping to change at line 690 skipping to change at page 14, line 51
REVISION "200203310000Z" -- March 31, 2002 REVISION "200203310000Z" -- March 31, 2002
DESCRIPTION "Added R. Abbi as co-author." DESCRIPTION "Added R. Abbi as co-author."
REVISION "200204090000Z" -- April 9, 2002 REVISION "200204090000Z" -- April 9, 2002
DESCRIPTION "Removed use of IMPLIED profile indices." DESCRIPTION "Removed use of IMPLIED profile indices."
REVISION "200206160000Z" -- June 16, 2002 REVISION "200206160000Z" -- June 16, 2002
DESCRIPTION "Revised per input from DSL Forum." DESCRIPTION "Revised per input from DSL Forum."
::= { transmission xxxx } REVISION "200209230000Z" -- September 23, 2002
DESCRIPTION "Revised per more input from DSL Forum."
::= { transmission xxxx }
vdslLineMib OBJECT IDENTIFIER ::= { vdslMIB 1 } vdslLineMib OBJECT IDENTIFIER ::= { vdslMIB 1 }
vdslMibObjects OBJECT IDENTIFIER ::= { vdslLineMib 1 } vdslMibObjects OBJECT IDENTIFIER ::= { vdslLineMib 1 }
-- --
-- textual conventions used in this MIB -- textual conventions used in this MIB
-- --
VdslLineCodingType ::= TEXTUAL-CONVENTION VdslLineCodingType ::= TEXTUAL-CONVENTION
STATUS current STATUS current
DESCRIPTION DESCRIPTION
skipping to change at line 713 skipping to change at page 15, line 25
Line Code." Line Code."
SYNTAX INTEGER SYNTAX INTEGER
{ {
other(1), -- none of the following other(1), -- none of the following
mcm(2), -- Multiple Carrier Modulation mcm(2), -- Multiple Carrier Modulation
scm(3) -- Single Carrier Modulation scm(3) -- Single Carrier Modulation
} }
VdslLineEntity ::= TEXTUAL-CONVENTION VdslLineEntity ::= TEXTUAL-CONVENTION
STATUS current STATUS current
Expires December 17, 2002 [PAGE 14]
DESCRIPTION DESCRIPTION
"Identifies a modem as being either Vtuc or Vtur. A "Identifies a modem as being either Vtuc or Vtur. A
VDSL line consists of two modems, a Vtuc and a Vtur." VDSL line consists of two modems, a Vtuc and a Vtur."
SYNTAX INTEGER SYNTAX INTEGER
{ {
vtuc(1), -- central site modem vtuc(1), -- central site modem
vtur(2) -- remote site modem vtur(2) -- remote site modem
} }
-- --
skipping to change at line 768 skipping to change at page 16, line 25
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Specifies the VDSL coding type used on this line." "Specifies the VDSL coding type used on this line."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslLineEntry 1 } ::= { vdslLineEntry 1 }
vdslLineType OBJECT-TYPE vdslLineType OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
Expires December 17, 2002 [PAGE 15]
noChannel(1), -- no channels exist noChannel(1), -- no channels exist
fastOnly(2), -- fast channel only fastOnly(2), -- fast channel only
slowOnly(3), -- slow channel only slowOnly(3), -- slow channel only
either(4), -- either fast or slow channel exist either(4), -- either fast or slow channel exist
both(5) -- both fast and slow channels exist both(5) -- both fast and slow channels exist
} }
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Defines the type of VDSL physical line "Defines the type of VDSL physical line
entity that exists, by defining whether and how entity that exists, by defining whether and how
the line is channelized. If the line is channelized, the line is channelized. If the line is channelized,
the value will be other than noChannel(1). This the value will be other than noChannel(1). This
object defines which channel type(s) are supported. object defines which channel type(s) are supported.
In the case that the line is channelized, the manager In the case that the line is channelized, the manager
can use the ifStackTable to determine the ifIndex for can use the ifStackTable to determine the ifIndex for
the associated channel(s)." the associated channel(s).
Note that slow and interleaved refer to the same
channel."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslLineEntry 2 } ::= { vdslLineEntry 2 }
vdslLineConfProfile OBJECT-TYPE vdslLineConfProfile OBJECT-TYPE
SYNTAX Integer32 SYNTAX Integer32
MAX-ACCESS read-write MAX-ACCESS read-write
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The value of this object identifies the row "The value of this object identifies the row
in the VDSL Line Configuration Profile Table, in the VDSL Line Configuration Profile Table,
skipping to change at line 824 skipping to change at page 17, line 31
SYNTAX SEQUENCE OF VdslPhysEntry SYNTAX SEQUENCE OF VdslPhysEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table provides one row for each Vtu. Each row "This table provides one row for each Vtu. Each row
contains the Physical Layer Parameters table for that contains the Physical Layer Parameters table for that
Vtu. VDSL physical interfaces are those ifEntries where Vtu. VDSL physical interfaces are those ifEntries where
ifType is equal to vdsl(97)." ifType is equal to vdsl(97)."
::= { vdslMibObjects 2 } ::= { vdslMibObjects 2 }
Expires December 17, 2002 [PAGE 16]
vdslPhysEntry OBJECT-TYPE vdslPhysEntry OBJECT-TYPE
SYNTAX VdslPhysEntry SYNTAX VdslPhysEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION "An entry in the vdslPhysTable." DESCRIPTION "An entry in the vdslPhysTable."
INDEX { ifIndex, INDEX { ifIndex,
vdslPhysSide } vdslPhysSide }
::= { vdslPhysTable 1 } ::= { vdslPhysTable 1 }
VdslPhysEntry ::= VdslPhysEntry ::=
skipping to change at line 877 skipping to change at page 18, line 31
SYNTAX SnmpAdminString (SIZE (0..16)) SYNTAX SnmpAdminString (SIZE (0..16))
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The vendor ID code is a copy of the binary vendor "The vendor ID code is a copy of the binary vendor
identification field expressed as readable characters." identification field expressed as readable characters."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslPhysEntry 3 } ::= { vdslPhysEntry 3 }
vdslInvVersionNumber OBJECT-TYPE vdslInvVersionNumber OBJECT-TYPE
Expires December 17, 2002 [PAGE 17]
SYNTAX SnmpAdminString (SIZE (0..16)) SYNTAX SnmpAdminString (SIZE (0..16))
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The vendor specific version number sent by this Vtu "The vendor specific version number sent by this Vtu
as part of the initialization messages. It is a copy as part of the initialization messages. It is a copy
of the binary version number field expressed as of the binary version number field expressed as
readable characters." readable characters."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslPhysEntry 4 } ::= { vdslPhysEntry 4 }
vdslCurrSnrMgn OBJECT-TYPE vdslCurrSnrMgn OBJECT-TYPE
SYNTAX Integer32(-640..640) SYNTAX Integer32 (-127..127)
UNITS "0.25dB" UNITS "0.25dBm"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Noise Margin as seen by this Vtu with respect to its "Noise Margin as seen by this Vtu with respect to its
received signal in 0.25dB." received signal in 0.25dB. The effective range is
-31.75 to +31.75dB."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslPhysEntry 5 } ::= { vdslPhysEntry 5 }
vdslCurrAtn OBJECT-TYPE vdslCurrAtn OBJECT-TYPE
SYNTAX Gauge32(0..630) SYNTAX Gauge32 (0..255)
UNITS "0.25dB" UNITS "0.25dBm"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Measured difference in the total power transmitted by "Measured difference in the total power transmitted by
the peer Vtu and the total power received by this Vtu." the peer Vtu and the total power received by this Vtu.
The effective range is 0 to +63.75dB."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslPhysEntry 6 } ::= { vdslPhysEntry 6 }
vdslCurrStatus OBJECT-TYPE vdslCurrStatus OBJECT-TYPE
SYNTAX BITS SYNTAX BITS
{ {
noDefect(0), noDefect(0),
lossOfFraming(1), lossOfFraming(1),
lossOfSignal(2), lossOfSignal(2),
lossOfPower(3), lossOfPower(3),
skipping to change at line 933 skipping to change at page 19, line 35
protocolInitFailure(8), protocolInitFailure(8),
noPeerVtuPresent(9) noPeerVtuPresent(9)
} }
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Indicates current state of the Vtu line. This is a "Indicates current state of the Vtu line. This is a
bit-map of possible conditions. The various bit bit-map of possible conditions. The various bit
positions are: positions are:
Expires December 17, 2002 [PAGE 18]
0 noDefect There no defects on the line 0 noDefect There no defects on the line
1 lossOfFraming Vtu failure due to not receiving 1 lossOfFraming Vtu failure due to not receiving
valid frame. valid frame.
2 lossOfSignal Vtu failure due to not receiving 2 lossOfSignal Vtu failure due to not receiving
signal. signal.
3 lossOfPower Vtu failure due to loss of power. 3 lossOfPower Vtu failure due to loss of power.
skipping to change at line 973 skipping to change at page 20, line 22
9 noPeerVtuPresent Vtu failure during initialization 9 noPeerVtuPresent Vtu failure during initialization
due to no activation sequence due to no activation sequence
detected from peer Vtu. detected from peer Vtu.
This is intended to supplement ifOperStatus." This is intended to supplement ifOperStatus."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslPhysEntry 7 } ::= { vdslPhysEntry 7 }
vdslCurrOutputPwr OBJECT-TYPE vdslCurrOutputPwr OBJECT-TYPE
SYNTAX Integer32(-310..310) SYNTAX Integer32 (0..160)
UNITS "0.25dBm" UNITS "0.1dBm"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Measured total output power transmitted by this ATU. "Measured total output power transmitted by this VTU.
This is the measurement that was reported during This is the measurement that was reported during
the last activation sequence." the last activation sequence."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslPhysEntry 8 } ::= { vdslPhysEntry 8 }
vdslCurrAttainableRate OBJECT-TYPE vdslCurrAttainableRate OBJECT-TYPE
SYNTAX Gauge32 SYNTAX Gauge32
UNITS "kbps"
Expires December 17, 2002 [PAGE 19]
UNITS "bps"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Indicates the maximum currently attainable data rate "Indicates the maximum currently attainable data rate
by the Vtu. This value will be equal or greater than in steps of 1024 bits/second by the Vtu. This value
the current line rate. Note that for SCM, the minimum will be equal or greater than the current line rate.
and maximum data rates are equal." Note that for SCM, the minimum and maximum data rates
are equal."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslPhysEntry 9 } ::= { vdslPhysEntry 9 }
vdslChanTable OBJECT-TYPE vdslChanTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslChanEntry SYNTAX SEQUENCE OF VdslChanEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table provides one row for each Vtu channel. "This table provides one row for each Vtu channel.
VDSL channel interfaces are those ifEntries where VDSL channel interfaces are those ifEntries where
skipping to change at line 1028 skipping to change at page 21, line 23
VdslChanEntry ::= VdslChanEntry ::=
SEQUENCE SEQUENCE
{ {
vdslChanInterleaveDelay Gauge32, vdslChanInterleaveDelay Gauge32,
vdslChanCrcBlockLength Gauge32 vdslChanCrcBlockLength Gauge32
} }
vdslChanInterleaveDelay OBJECT-TYPE vdslChanInterleaveDelay OBJECT-TYPE
SYNTAX Gauge32 SYNTAX Gauge32
UNITS "milli-seconds" UNITS "ms"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Interleave Delay for this channel. "Interleave Delay for this channel.
Interleave delay applies only to the interleave Interleave delay applies only to the interleave
(slow) channel and defines the mapping (relative (slow) channel and defines the mapping (relative
spacing) between subsequent input bytes at the spacing) between subsequent input bytes at the
interleaver input and their placement in the bit interleaver input and their placement in the bit
stream at the interleaver output. Larger numbers stream at the interleaver output. Larger numbers
provide greater separation between consecutive provide greater separation between consecutive
input bytes in the output bit stream allowing for input bytes in the output bit stream allowing for
Expires December 17, 2002 [PAGE 20]
improved impulse noise immunity at the expense of improved impulse noise immunity at the expense of
payload latency. payload latency.
In the case where the ifType is fast(125), use In the case where the ifType is fast(125), use
noSuchObject." noSuchObject."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslChanEntry 1 } ::= { vdslChanEntry 1 }
vdslChanCrcBlockLength OBJECT-TYPE vdslChanCrcBlockLength OBJECT-TYPE
SYNTAX Gauge32 SYNTAX Gauge32
skipping to change at line 1085 skipping to change at page 22, line 27
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the vdslPerfDataTable." "An entry in the vdslPerfDataTable."
INDEX { ifIndex, INDEX { ifIndex,
vdslPhysSide } vdslPhysSide }
::= { vdslPerfDataTable 1 } ::= { vdslPerfDataTable 1 }
VdslPerfDataEntry ::= VdslPerfDataEntry ::=
SEQUENCE SEQUENCE
{ {
vdslPerfValidIntervals Unsigned32, vdslPerfValidIntervals HCPerfValidIntervals,
vdslPerfInvalidIntervals Unsigned32, vdslPerfInvalidIntervals HCPerfInvalidIntervals,
vdslPerfLofs Counter64, vdslPerfLofs Counter64,
vdslPerfLoss Counter64, vdslPerfLoss Counter64,
vdslPerfLprs Counter64, vdslPerfLprs Counter64,
vdslPerfESs Counter64, vdslPerfESs Counter64,
vdslPerfSESs Counter64, vdslPerfSESs Counter64,
vdslPerfUASs Counter64, vdslPerfUASs Counter64,
vdslPerfInits Counter64, vdslPerfInits Counter64,
vdslPerfCurr15MinTimeElapsed Unsigned32, vdslPerfCurr15MinTimeElapsed HCPerfTimeElapsed,
vdslPerfCurr15MinLofs HCPerfCurrentCount, vdslPerfCurr15MinLofs HCPerfCurrentCount,
Expires December 17, 2002 [PAGE 21]
vdslPerfCurr15MinLoss HCPerfCurrentCount, vdslPerfCurr15MinLoss HCPerfCurrentCount,
vdslPerfCurr15MinLprs HCPerfCurrentCount, vdslPerfCurr15MinLprs HCPerfCurrentCount,
vdslPerfCurr15MinESs HCPerfCurrentCount, vdslPerfCurr15MinESs HCPerfCurrentCount,
vdslPerfCurr15MinSESs HCPerfCurrentCount, vdslPerfCurr15MinSESs HCPerfCurrentCount,
vdslPerfCurr15MinUASs HCPerfCurrentCount, vdslPerfCurr15MinUASs HCPerfCurrentCount,
vdslPerfCurr15MinInits HCPerfCurrentCount, vdslPerfCurr15MinInits HCPerfCurrentCount,
vdslPerf1DayValidIntervals Unsigned32, vdslPerf1DayValidIntervals HCPerfValidIntervals,
vdslPerf1DayInvalidIntervals Unsigned32, vdslPerf1DayInvalidIntervals HCPerfInvalidIntervals,
vdslPerfCurr1DayTimeElapsed Unsigned32, vdslPerfCurr1DayTimeElapsed HCPerfTimeElapsed,
vdslPerfCurr1DayLofs Counter64, vdslPerfCurr1DayLofs Counter64,
vdslPerfCurr1DayLoss Counter64, vdslPerfCurr1DayLoss Counter64,
vdslPerfCurr1DayLprs Counter64, vdslPerfCurr1DayLprs Counter64,
vdslPerfCurr1DayESs Counter64, vdslPerfCurr1DayESs Counter64,
vdslPerfCurr1DaySESs Counter64, vdslPerfCurr1DaySESs Counter64,
vdslPerfCurr1DayUASs Counter64, vdslPerfCurr1DayUASs Counter64,
vdslPerfCurr1DayInits Counter64 vdslPerfCurr1DayInits Counter64
} }
vdslPerfValidIntervals OBJECT-TYPE vdslPerfValidIntervals OBJECT-TYPE
SYNTAX Unsigned32(0..96) SYNTAX HCPerfValidIntervals
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Valid Intervals per xxxValidInterval definition "Valid Intervals per definition found in
found in HC-PerfHist-TC-MIB." HC-PerfHist-TC-MIB."
::= { vdslPerfDataEntry 1 } ::= { vdslPerfDataEntry 1 }
vdslPerfInvalidIntervals OBJECT-TYPE vdslPerfInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32(0..96) SYNTAX HCPerfInvalidIntervals
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Invalid Intervals per xxxInvalidInterval definition "Invalid Intervals per definition found in
found in HC-PerfHist-TC-MIB." HC-PerfHist-TC-MIB."
::= { vdslPerfDataEntry 2 } ::= { vdslPerfDataEntry 2 }
vdslPerfLofs OBJECT-TYPE vdslPerfLofs OBJECT-TYPE
SYNTAX Counter64 SYNTAX Counter64
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of seconds since the unit was last reset that there "Count of seconds since the unit was last reset that there
was Loss of Framing." was Loss of Framing."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslPerfDataEntry 3 } ::= { vdslPerfDataEntry 3 }
vdslPerfLoss OBJECT-TYPE vdslPerfLoss OBJECT-TYPE
SYNTAX Counter64 SYNTAX Counter64
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
Expires December 17, 2002 [PAGE 22]
"Count of seconds since the unit was last reset that there "Count of seconds since the unit was last reset that there
was Loss of Signal." was Loss of Signal."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslPerfDataEntry 4 } ::= { vdslPerfDataEntry 4 }
vdslPerfLprs OBJECT-TYPE vdslPerfLprs OBJECT-TYPE
SYNTAX Counter64 SYNTAX Counter64
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
skipping to change at line 1206 skipping to change at page 24, line 40
DESCRIPTION DESCRIPTION
"Count of Unavailable Seconds since the unit was last "Count of Unavailable Seconds since the unit was last
reset." reset."
::= { vdslPerfDataEntry 8 } ::= { vdslPerfDataEntry 8 }
vdslPerfInits OBJECT-TYPE vdslPerfInits OBJECT-TYPE
SYNTAX Counter64 SYNTAX Counter64
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
Expires December 17, 2002 [PAGE 23]
"Count of the line initialization attempts since the unit "Count of the line initialization attempts since the unit
was last reset. This count includes both successful and was last reset. This count includes both successful and
failed attempts." failed attempts."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslPerfDataEntry 9 } ::= { vdslPerfDataEntry 9 }
vdslPerfCurr15MinTimeElapsed OBJECT-TYPE vdslPerfCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX Unsigned32(0..899) SYNTAX HCPerfTimeElapsed
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Total elapsed seconds in this interval." "Total elapsed seconds in this interval."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslPerfDataEntry 10 } ::= { vdslPerfDataEntry 10 }
vdslPerfCurr15MinLofs OBJECT-TYPE vdslPerfCurr15MinLofs OBJECT-TYPE
SYNTAX HCPerfCurrentCount SYNTAX HCPerfCurrentCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of seconds during this interval that there "Count of seconds during this interval that there
was Loss of Framing." was Loss of Framing."
skipping to change at line 1261 skipping to change at page 25, line 40
DESCRIPTION DESCRIPTION
"Count of seconds during this interval that there "Count of seconds during this interval that there
was Loss of Power." was Loss of Power."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslPerfDataEntry 13 } ::= { vdslPerfDataEntry 13 }
vdslPerfCurr15MinESs OBJECT-TYPE vdslPerfCurr15MinESs OBJECT-TYPE
SYNTAX HCPerfCurrentCount SYNTAX HCPerfCurrentCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
Expires December 17, 2002 [PAGE 24]
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Errored Seconds during this interval. An Errored "Count of Errored Seconds during this interval. An Errored
Second is a one-second interval containing one or more crc Second is a one-second interval containing one or more crc
anomalies, or one or more los or lof defects." anomalies, or one or more los or lof defects."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslPerfDataEntry 14 } ::= { vdslPerfDataEntry 14 }
vdslPerfCurr15MinSESs OBJECT-TYPE vdslPerfCurr15MinSESs OBJECT-TYPE
SYNTAX HCPerfCurrentCount SYNTAX HCPerfCurrentCount
skipping to change at line 1301 skipping to change at page 26, line 25
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of the line initialization attempts during this "Count of the line initialization attempts during this
interval. This count includes both successful and interval. This count includes both successful and
failed attempts." failed attempts."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslPerfDataEntry 17 } ::= { vdslPerfDataEntry 17 }
vdslPerf1DayValidIntervals OBJECT-TYPE vdslPerf1DayValidIntervals OBJECT-TYPE
SYNTAX Unsigned32(0..30) SYNTAX HCPerfValidIntervals
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Valid Intervals per xxxValidInterval definition "Valid Intervals per definition found in
found in HC-PerfHist-TC-MIB." HC-PerfHist-TC-MIB."
::= { vdslPerfDataEntry 18 } ::= { vdslPerfDataEntry 18 }
vdslPerf1DayInvalidIntervals OBJECT-TYPE vdslPerf1DayInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32(0..30) SYNTAX HCPerfInvalidIntervals
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Invalid Intervals per xxxInvalidInterval definition "Invalid Intervals per definition found in
found in HC-PerfHist-TC-MIB." HC-PerfHist-TC-MIB."
Expires December 17, 2002 [PAGE 25]
::= { vdslPerfDataEntry 19 } ::= { vdslPerfDataEntry 19 }
vdslPerfCurr1DayTimeElapsed OBJECT-TYPE vdslPerfCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX Unsigned32(0..86399) SYNTAX HCPerfTimeElapsed
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Number of seconds that have elapsed since the beginning "Number of seconds that have elapsed since the beginning
of the current 1-day interval." of the current 1-day interval."
::= { vdslPerfDataEntry 20 } ::= { vdslPerfDataEntry 20 }
vdslPerfCurr1DayLofs OBJECT-TYPE vdslPerfCurr1DayLofs OBJECT-TYPE
SYNTAX Counter64 SYNTAX Counter64
skipping to change at line 1371 skipping to change at page 27, line 42
SYNTAX Counter64 SYNTAX Counter64
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Errored Seconds (ES) since the beginning "Count of Errored Seconds (ES) since the beginning
of the current 1-day interval." of the current 1-day interval."
::= { vdslPerfDataEntry 24 } ::= { vdslPerfDataEntry 24 }
vdslPerfCurr1DaySESs OBJECT-TYPE vdslPerfCurr1DaySESs OBJECT-TYPE
Expires December 17, 2002 [PAGE 26]
SYNTAX Counter64 SYNTAX Counter64
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Severely Errored Seconds (SES) since the "Count of Severely Errored Seconds (SES) since the
beginning of the current 1-day interval." beginning of the current 1-day interval."
::= { vdslPerfDataEntry 25 } ::= { vdslPerfDataEntry 25 }
vdslPerfCurr1DayUASs OBJECT-TYPE vdslPerfCurr1DayUASs OBJECT-TYPE
skipping to change at line 1426 skipping to change at page 28, line 43
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the vdslPerfIntervalTable." "An entry in the vdslPerfIntervalTable."
INDEX { ifIndex, INDEX { ifIndex,
vdslPhysSide, vdslPhysSide,
vdslIntervalNumber } vdslIntervalNumber }
::= { vdslPerfIntervalTable 1 } ::= { vdslPerfIntervalTable 1 }
VdslPerfIntervalEntry ::= VdslPerfIntervalEntry ::=
SEQUENCE SEQUENCE
Expires December 17, 2002 [PAGE 27]
{ {
vdslIntervalNumber Unsigned32, vdslIntervalNumber Unsigned32,
vdslIntervalLofs HCPerfIntervalCount, vdslIntervalLofs HCPerfIntervalCount,
vdslIntervalLoss HCPerfIntervalCount, vdslIntervalLoss HCPerfIntervalCount,
vdslIntervalLprs HCPerfIntervalCount, vdslIntervalLprs HCPerfIntervalCount,
vdslIntervalESs HCPerfIntervalCount, vdslIntervalESs HCPerfIntervalCount,
vdslIntervalSESs HCPerfIntervalCount, vdslIntervalSESs HCPerfIntervalCount,
vdslIntervalUASs HCPerfIntervalCount, vdslIntervalUASs HCPerfIntervalCount,
vdslIntervalInits HCPerfIntervalCount vdslIntervalInits HCPerfIntervalCount
} }
skipping to change at line 1482 skipping to change at page 29, line 45
SYNTAX HCPerfIntervalCount SYNTAX HCPerfIntervalCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of seconds in the interval when there was Loss "Count of seconds in the interval when there was Loss
of Power." of Power."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslPerfIntervalEntry 4 } ::= { vdslPerfIntervalEntry 4 }
Expires December 17, 2002 [PAGE 28]
vdslIntervalESs OBJECT-TYPE vdslIntervalESs OBJECT-TYPE
SYNTAX HCPerfIntervalCount SYNTAX HCPerfIntervalCount
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of Errored Seconds (ES) in the interval. An Errored "Count of Errored Seconds (ES) in the interval. An Errored
Second is a one-second interval containing one or more crc Second is a one-second interval containing one or more crc
anomalies, one or more los or lof defects." anomalies, one or more los or lof defects."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
skipping to change at line 1535 skipping to change at page 30, line 44
SYNTAX SEQUENCE OF Vdsl1DayIntervalEntry SYNTAX SEQUENCE OF Vdsl1DayIntervalEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table provides one row for each VDSL performance "This table provides one row for each VDSL performance
data collection interval. This table contains live data data collection interval. This table contains live data
from equipment. As such, it is NOT persistent." from equipment. As such, it is NOT persistent."
::= { vdslMibObjects 6 } ::= { vdslMibObjects 6 }
vdsl1DayIntervalEntry OBJECT-TYPE vdsl1DayIntervalEntry OBJECT-TYPE
Expires December 17, 2002 [PAGE 29]
SYNTAX Vdsl1DayIntervalEntry SYNTAX Vdsl1DayIntervalEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the vdsl1DayIntervalTable." "An entry in the vdsl1DayIntervalTable."
INDEX { ifIndex, INDEX { ifIndex,
vdslPhysSide, vdslPhysSide,
vdsl1DayIntervalNumber } vdsl1DayIntervalNumber }
::= { vdsl1DayIntervalTable 1 } ::= { vdsl1DayIntervalTable 1 }
Vdsl1DayIntervalEntry ::= Vdsl1DayIntervalEntry ::=
SEQUENCE SEQUENCE
{ {
vdsl1DayIntervalNumber Unsigned32, vdsl1DayIntervalNumber Unsigned32,
vdsl1DayIntervalMoniSecs Unsigned32, vdsl1DayIntervalMoniSecs HCPerfTimeElapsed,
vdsl1DayIntervalLofs Counter64, vdsl1DayIntervalLofs Counter64,
vdsl1DayIntervalLoss Counter64, vdsl1DayIntervalLoss Counter64,
vdsl1DayIntervalLprs Counter64, vdsl1DayIntervalLprs Counter64,
vdsl1DayIntervalESs Counter64, vdsl1DayIntervalESs Counter64,
vdsl1DayIntervalSESs Counter64, vdsl1DayIntervalSESs Counter64,
vdsl1DayIntervalUASs Counter64, vdsl1DayIntervalUASs Counter64,
vdsl1DayIntervalInits Counter64 vdsl1DayIntervalInits Counter64
} }
vdsl1DayIntervalNumber OBJECT-TYPE vdsl1DayIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32(1..30) SYNTAX Unsigned32(1..30)
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"History Data Interval number. Interval 1 is the the most "History Data Interval number. Interval 1 is the the most
recent previous day; interval 30 is 30 days ago. Intervals recent previous day; interval 30 is 30 days ago. Intervals
2..30 are optional." 2..30 are optional."
::= { vdsl1DayIntervalEntry 1 } ::= { vdsl1DayIntervalEntry 1 }
vdsl1DayIntervalMoniSecs OBJECT-TYPE vdsl1DayIntervalMoniSecs OBJECT-TYPE
SYNTAX Unsigned32(0..86400) SYNTAX HCPerfTimeElapsed
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The amount of time in the 1-day interval over which the "The amount of time in the 1-day interval over which the
performance monitoring information is actually counted. performance monitoring information is actually counted.
This value will be the same as the interval duration except This value will be the same as the interval duration except
in a situation where performance monitoring data could not in a situation where performance monitoring data could not
be collected for any reason." be collected for any reason."
::= { vdsl1DayIntervalEntry 2 } ::= { vdsl1DayIntervalEntry 2 }
vdsl1DayIntervalLofs OBJECT-TYPE vdsl1DayIntervalLofs OBJECT-TYPE
SYNTAX Counter64 SYNTAX Counter64
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
Expires December 17, 2002 [PAGE 30]
"Count of Loss of Frame (LOF) Seconds during the 1-day "Count of Loss of Frame (LOF) Seconds during the 1-day
interval as measured by vdsl1DayIntervalMoniSecs." interval as measured by vdsl1DayIntervalMoniSecs."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdsl1DayIntervalEntry 3 } ::= { vdsl1DayIntervalEntry 3 }
vdsl1DayIntervalLoss OBJECT-TYPE vdsl1DayIntervalLoss OBJECT-TYPE
SYNTAX Counter64 SYNTAX Counter64
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
skipping to change at line 1645 skipping to change at page 32, line 47
DESCRIPTION DESCRIPTION
"Count of Severely Errored Seconds (SES) during the 1-day "Count of Severely Errored Seconds (SES) during the 1-day
interval as measured by vdsl1DayIntervalMoniSecs." interval as measured by vdsl1DayIntervalMoniSecs."
::= { vdsl1DayIntervalEntry 7 } ::= { vdsl1DayIntervalEntry 7 }
vdsl1DayIntervalUASs OBJECT-TYPE vdsl1DayIntervalUASs OBJECT-TYPE
SYNTAX Counter64 SYNTAX Counter64
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
Expires December 17, 2002 [PAGE 31]
DESCRIPTION DESCRIPTION
"Count of Unavailable Seconds (UAS) during the 1-day "Count of Unavailable Seconds (UAS) during the 1-day
interval as measured by vdsl1DayIntervalMoniSecs." interval as measured by vdsl1DayIntervalMoniSecs."
::= { vdsl1DayIntervalEntry 8 } ::= { vdsl1DayIntervalEntry 8 }
vdsl1DayIntervalInits OBJECT-TYPE vdsl1DayIntervalInits OBJECT-TYPE
SYNTAX Counter64 SYNTAX Counter64
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
skipping to change at line 1687 skipping to change at page 33, line 35
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the vdslChanPerfDataTable." "An entry in the vdslChanPerfDataTable."
INDEX { ifIndex, INDEX { ifIndex,
vdslPhysSide } vdslPhysSide }
::= { vdslChanPerfDataTable 1 } ::= { vdslChanPerfDataTable 1 }
VdslChanPerfDataEntry ::= VdslChanPerfDataEntry ::=
SEQUENCE SEQUENCE
{ {
vdslChanPerfValidIntervals Unsigned32, vdslChanPerfValidIntervals HCPerfValidIntervals,
vdslChanPerfInvalidIntervals Unsigned32, vdslChanPerfInvalidIntervals HCPerfInvalidIntervals,
vdslChanCorrectedOctets Counter64, vdslChanCorrectedOctets Counter64,
vdslChanUncorrectBlks Counter64, vdslChanUncorrectBlks Counter64,
vdslChanPerfCurr15MinTimeElapsed Unsigned32, vdslChanPerfCurr15MinTimeElapsed HCPerfTimeElapsed,
vdslChanPerfCurr15MinCorrectedOctets HCPerfCurrentCount, vdslChanPerfCurr15MinCorrectedOctets HCPerfCurrentCount,
vdslChanPerfCurr15MinUncorrectBlks HCPerfCurrentCount, vdslChanPerfCurr15MinUncorrectBlks HCPerfCurrentCount,
vdslChanPerf1DayValidIntervals Unsigned32, vdslChanPerf1DayValidIntervals HCPerfValidIntervals,
vdslChanPerf1DayInvalidIntervals Unsigned32, vdslChanPerf1DayInvalidIntervals HCPerfInvalidIntervals,
vdslChanPerfCurr1DayTimeElapsed Unsigned32, vdslChanPerfCurr1DayTimeElapsed HCPerfTimeElapsed,
vdslChanPerfCurr1DayCorrectedOctets HCPerfCurrentCount, vdslChanPerfCurr1DayCorrectedOctets HCPerfCurrentCount,
vdslChanPerfCurr1DayUncorrectBlks HCPerfCurrentCount vdslChanPerfCurr1DayUncorrectBlks HCPerfCurrentCount
} }
Expires December 17, 2002 [PAGE 32]
vdslChanPerfValidIntervals OBJECT-TYPE vdslChanPerfValidIntervals OBJECT-TYPE
SYNTAX Unsigned32(0..96) SYNTAX HCPerfValidIntervals
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Valid Intervals per xxxValidInterval definition "Valid Intervals per definition found in
found in HC-PerfHist-TC-MIB." HC-PerfHist-TC-MIB."
::= { vdslChanPerfDataEntry 1 } ::= { vdslChanPerfDataEntry 1 }
vdslChanPerfInvalidIntervals OBJECT-TYPE vdslChanPerfInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32(0..96) SYNTAX HCPerfInvalidIntervals
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Invalid Intervals per xxxInvalidInterval definition "Invalid Intervals per definition found in
found in HC-PerfHist-TC-MIB." HC-PerfHist-TC-MIB."
::= { vdslChanPerfDataEntry 2 } ::= { vdslChanPerfDataEntry 2 }
vdslChanCorrectedOctets OBJECT-TYPE vdslChanCorrectedOctets OBJECT-TYPE
SYNTAX Counter64 SYNTAX Counter64
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of corrected octets since the unit was last reset." "Count of corrected octets since the unit was last reset."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslChanPerfDataEntry 3 } ::= { vdslChanPerfDataEntry 3 }
skipping to change at line 1739 skipping to change at page 34, line 34
vdslChanUncorrectBlks OBJECT-TYPE vdslChanUncorrectBlks OBJECT-TYPE
SYNTAX Counter64 SYNTAX Counter64
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of uncorrected blocks since the unit was last reset." "Count of uncorrected blocks since the unit was last reset."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslChanPerfDataEntry 4 } ::= { vdslChanPerfDataEntry 4 }
vdslChanPerfCurr15MinTimeElapsed OBJECT-TYPE vdslChanPerfCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX Unsigned32(0..899) SYNTAX HCPerfTimeElapsed
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Total elapsed seconds in this interval." "Total elapsed seconds in this interval."
::= { vdslChanPerfDataEntry 5 } ::= { vdslChanPerfDataEntry 5 }
vdslChanPerfCurr15MinCorrectedOctets OBJECT-TYPE vdslChanPerfCurr15MinCorrectedOctets OBJECT-TYPE
SYNTAX HCPerfCurrentCount SYNTAX HCPerfCurrentCount
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of corrected octets in this interval." "Count of corrected octets in this interval."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
Expires December 17, 2002 [PAGE 33]
::= { vdslChanPerfDataEntry 6 } ::= { vdslChanPerfDataEntry 6 }
vdslChanPerfCurr15MinUncorrectBlks OBJECT-TYPE vdslChanPerfCurr15MinUncorrectBlks OBJECT-TYPE
SYNTAX HCPerfCurrentCount SYNTAX HCPerfCurrentCount
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of uncorrected blocks in this interval." "Count of uncorrected blocks in this interval."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslChanPerfDataEntry 7 } ::= { vdslChanPerfDataEntry 7 }
vdslChanPerf1DayValidIntervals OBJECT-TYPE vdslChanPerf1DayValidIntervals OBJECT-TYPE
SYNTAX Unsigned32(0..30) SYNTAX HCPerfValidIntervals
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Valid Intervals per xxxValidInterval definition "Valid Intervals per definition found in
found in HC-PerfHist-TC-MIB." HC-PerfHist-TC-MIB."
::= { vdslChanPerfDataEntry 8 } ::= { vdslChanPerfDataEntry 8 }
vdslChanPerf1DayInvalidIntervals OBJECT-TYPE vdslChanPerf1DayInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32(0..30) SYNTAX HCPerfInvalidIntervals
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Invalid Intervals per xxxInvalidInterval definition "Invalid Intervals per definition found in
found in HC-PerfHist-TC-MIB." HC-PerfHist-TC-MIB."
::= { vdslChanPerfDataEntry 9 } ::= { vdslChanPerfDataEntry 9 }
vdslChanPerfCurr1DayTimeElapsed OBJECT-TYPE vdslChanPerfCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX Unsigned32(0..86399) SYNTAX HCPerfTimeElapsed
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Number of seconds that have elapsed since the beginning "Number of seconds that have elapsed since the beginning
of the current 1-day interval." of the current 1-day interval."
::= { vdslChanPerfDataEntry 10 } ::= { vdslChanPerfDataEntry 10 }
vdslChanPerfCurr1DayCorrectedOctets OBJECT-TYPE vdslChanPerfCurr1DayCorrectedOctets OBJECT-TYPE
SYNTAX HCPerfCurrentCount SYNTAX HCPerfCurrentCount
skipping to change at line 1809 skipping to change at page 35, line 50
DESCRIPTION DESCRIPTION
"Count of corrected octets since the beginning of the "Count of corrected octets since the beginning of the
current 1-day interva." current 1-day interva."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslChanPerfDataEntry 11 } ::= { vdslChanPerfDataEntry 11 }
vdslChanPerfCurr1DayUncorrectBlks OBJECT-TYPE vdslChanPerfCurr1DayUncorrectBlks OBJECT-TYPE
SYNTAX HCPerfCurrentCount SYNTAX HCPerfCurrentCount
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
Expires December 17, 2002 [PAGE 34]
DESCRIPTION DESCRIPTION
"Count of uncorrected blocks since the beginning of the "Count of uncorrected blocks since the beginning of the
current 1-day interva." current 1-day interva."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslChanPerfDataEntry 12 } ::= { vdslChanPerfDataEntry 12 }
vdslChanIntervalTable OBJECT-TYPE vdslChanIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslChanIntervalEntry SYNTAX SEQUENCE OF VdslChanIntervalEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table provides one row for each Vtu channel data "This table provides one row for each Vtu channel data
collection interval. VDSL channel interfaces are those collection interval. VDSL channel interfaces are those
ifEntries where ifType is equal to interleave(124) or ifEntries where ifType is equal to interleave(124) or
fast(125)." fast(125)."
::= { vdslMibObjects 8 } ::= { vdslMibObjects 8 }
skipping to change at line 1864 skipping to change at page 36, line 51
Intervals 2..96 are optional." Intervals 2..96 are optional."
::= { vdslChanIntervalEntry 1 } ::= { vdslChanIntervalEntry 1 }
vdslChanIntervalCorrectedOctets OBJECT-TYPE vdslChanIntervalCorrectedOctets OBJECT-TYPE
SYNTAX HCPerfIntervalCount SYNTAX HCPerfIntervalCount
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of corrected octets in this interval." "Count of corrected octets in this interval."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
Expires December 17, 2002 [PAGE 35]
::= { vdslChanIntervalEntry 2 } ::= { vdslChanIntervalEntry 2 }
vdslChanIntervalUncorrectBlks OBJECT-TYPE vdslChanIntervalUncorrectBlks OBJECT-TYPE
SYNTAX HCPerfIntervalCount SYNTAX HCPerfIntervalCount
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Count of uncorrected blocks in this interval." "Count of uncorrected blocks in this interval."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslChanIntervalEntry 3 } ::= { vdslChanIntervalEntry 3 }
skipping to change at line 1902 skipping to change at page 37, line 35
"An entry in the vdslChan1DayIntervalTable." "An entry in the vdslChan1DayIntervalTable."
INDEX { ifIndex, INDEX { ifIndex,
vdslPhysSide, vdslPhysSide,
vdslChan1DayIntervalNumber } vdslChan1DayIntervalNumber }
::= { vdslChan1DayIntervalTable 1 } ::= { vdslChan1DayIntervalTable 1 }
VdslChan1DayIntervalEntry ::= VdslChan1DayIntervalEntry ::=
SEQUENCE SEQUENCE
{ {
vdslChan1DayIntervalNumber Unsigned32, vdslChan1DayIntervalNumber Unsigned32,
vdslChan1DayIntervalMoniSecs Unsigned32, vdslChan1DayIntervalMoniSecs HCPerfTimeElapsed,
vdslChan1DayIntervalCorrectedOctets HCPerfCurrentCount, vdslChan1DayIntervalCorrectedOctets HCPerfCurrentCount,
vdslChan1DayIntervalUncorrectBlks HCPerfCurrentCount vdslChan1DayIntervalUncorrectBlks HCPerfCurrentCount
} }
vdslChan1DayIntervalNumber OBJECT-TYPE vdslChan1DayIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32(1..30) SYNTAX Unsigned32(1..30)
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"History Data Interval number. Interval 1 is the the most "History Data Interval number. Interval 1 is the the most
recent previous day; interval 30 is 30 days ago. Intervals recent previous day; interval 30 is 30 days ago. Intervals
2..30 are optional." 2..30 are optional."
::= { vdslChan1DayIntervalEntry 1 } ::= { vdslChan1DayIntervalEntry 1 }
vdslChan1DayIntervalMoniSecs OBJECT-TYPE vdslChan1DayIntervalMoniSecs OBJECT-TYPE
SYNTAX Unsigned32(0..86400) SYNTAX HCPerfTimeElapsed
Expires December 17, 2002 [PAGE 36]
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The amount of time in the 1-day interval over which the "The amount of time in the 1-day interval over which the
performance monitoring information is actually counted. performance monitoring information is actually counted.
This value will be the same as the interval duration except This value will be the same as the interval duration except
in a situation where performance monitoring data could not in a situation where performance monitoring data could not
be collected for any reason." be collected for any reason."
::= { vdslChan1DayIntervalEntry 2 } ::= { vdslChan1DayIntervalEntry 2 }
skipping to change at line 1974 skipping to change at page 38, line 53
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry in the vdslSCMPhysBandTable." "An entry in the vdslSCMPhysBandTable."
INDEX { ifIndex, INDEX { ifIndex,
vdslPhysSide, vdslPhysSide,
vdslSCMPhysTxBandNumber } vdslSCMPhysTxBandNumber }
::= { vdslSCMPhysBandTable 1 } ::= { vdslSCMPhysBandTable 1 }
VdslSCMPhysBandEntry ::= VdslSCMPhysBandEntry ::=
Expires December 17, 2002 [PAGE 37]
SEQUENCE SEQUENCE
{ {
vdslSCMPhysTxBandNumber INTEGER, vdslSCMPhysTxBandNumber INTEGER,
vdslSCMPhysBandSnrMgn Integer32, vdslSCMPhysBandSnrMgn Integer32,
vdslSCMPhysBandAtn Unsigned32 vdslSCMPhysBandAtn Unsigned32
} }
vdslSCMPhysTxBandNumber OBJECT-TYPE vdslSCMPhysTxBandNumber OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
skipping to change at line 1998 skipping to change at page 39, line 23
upstreamU0(3) upstreamU0(3)
} }
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The SCM transmit band number for this entry." "The SCM transmit band number for this entry."
::= { vdslSCMPhysBandEntry 1 } ::= { vdslSCMPhysBandEntry 1 }
vdslSCMPhysBandSnrMgn OBJECT-TYPE vdslSCMPhysBandSnrMgn OBJECT-TYPE
SYNTAX Integer32(-127..127) SYNTAX Integer32(-127..127)
UNITS "0.25 dB" UNITS "0.25 dBm"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Noise margin as seen by this Vtu and band with respect "Noise margin as seen by this Vtu and band with respect
to its received signal in 0.25 dB." to its received signal in 0.25 dB."
::= { vdslSCMPhysBandEntry 2 } ::= { vdslSCMPhysBandEntry 2 }
vdslSCMPhysBandAtn OBJECT-TYPE vdslSCMPhysBandAtn OBJECT-TYPE
SYNTAX Unsigned32(0..255) SYNTAX Unsigned32(0..255)
UNITS "0.25 dB" UNITS "0.25 dBm"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Measured difference in the total power transmitted by "Measured difference in the total power transmitted by
the peer Vtu on this band and the total power received the peer Vtu on this band and the total power received
by this Vtu on this band in 0.25 dB." by this Vtu on this band in 0.25 dB."
::= { vdslSCMPhysBandEntry 3 } ::= { vdslSCMPhysBandEntry 3 }
-- --
-- profile tables -- profile tables
-- --
vdslLineConfProfileTable OBJECT-TYPE vdslLineConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslLineConfProfileEntry SYNTAX SEQUENCE OF VdslLineConfProfileEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table contains information on the VDSL line "This table contains information on the VDSL line
configuration. One entry in this table reflects a configuration. One entry in this table reflects a
profile defined by a manager which can be used to profile defined by a manager which can be used to
Expires December 17, 2002 [PAGE 38]
configure the VDSL line." configure the VDSL line."
::= { vdslMibObjects 11 } ::= { vdslMibObjects 11 }
vdslLineConfProfileEntry OBJECT-TYPE vdslLineConfProfileEntry OBJECT-TYPE
SYNTAX VdslLineConfProfileEntry SYNTAX VdslLineConfProfileEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Each entry consists of a list of parameters that "Each entry consists of a list of parameters that
represents the configuration of a VDSL line. A represents the configuration of a VDSL line. A
default profile with an index of 1 will always exist default profile with an index of 1 will always exist
and its parameters will be set to vendor specific and its parameters will be set to vendor specific
values, unless otherwise specified in this document." values, unless otherwise specified in this document."
skipping to change at line 2052 skipping to change at page 40, line 22
and its parameters will be set to vendor specific and its parameters will be set to vendor specific
values, unless otherwise specified in this document." values, unless otherwise specified in this document."
INDEX { vdslLineConfProfileIndex } INDEX { vdslLineConfProfileIndex }
::= { vdslLineConfProfileTable 1 } ::= { vdslLineConfProfileTable 1 }
VdslLineConfProfileEntry ::= VdslLineConfProfileEntry ::=
SEQUENCE SEQUENCE
{ {
vdslLineConfProfileIndex Unsigned32, vdslLineConfProfileIndex Unsigned32,
vdslLineConfProfileName SnmpAdminString, vdslLineConfProfileName SnmpAdminString,
vdslLineConfTargetSnrMgn Unsigned32, vdslLineConfDownstreamMaxPwr Unsigned32,
vdslLineConfUpstreamTxSpeed Unsigned32, vdslLineConfUpstreamMaxPwr Unsigned32,
vdslLineConfDownstreamTxSpeed Unsigned32, vdslLineConfDownstreamMaxSnrMgn Unsigned32,
vdslLineConfDownstreamMinSnrMgn Unsigned32,
vdslLineConfDownstreamTargetSnrMgn Unsigned32,
vdslLineConfUpstreamMaxSnrMgn Unsigned32,
vdslLineConfUpstreamMinSnrMgn Unsigned32,
vdslLineConfUpstreamTargetSnrMgn Unsigned32,
vdslLineConfDownstreamFastMaxDataRate Unsigned32,
vdslLineConfDownstreamFastMinDataRate Unsigned32,
vdslLineConfDownstreamSlowMaxDataRate Unsigned32,
vdslLineConfDownstreamSlowMinDataRate Unsigned32,
vdslLineConfUpstreamFastMaxDataRate Unsigned32,
vdslLineConfUpstreamFastMinDataRate Unsigned32,
vdslLineConfUpstreamSlowMaxDataRate Unsigned32,
vdslLineConfUpstreamSlowMinDataRate Unsigned32,
vdslLineConfRateAdaptationRatio Unsigned32,
vdslLineConfUpstreamDataRate Unsigned32,
vdslLineConfDownstreamDataRate Unsigned32,
vdslLineConfDownstreamMaxInterDelay Unsigned32,
vdslLineConfUpstreamMaxInterDelay Unsigned32,
vdslLineConfUpstreamPboControl INTEGER, vdslLineConfUpstreamPboControl INTEGER,
vdslLineConfDownstreamPboControl INTEGER, vdslLineConfDownstreamPboControl INTEGER,
vdslLineConfDeploymentScenario INTEGER, vdslLineConfDeploymentScenario INTEGER,
vdslLineConfAdslOccupy TruthValue, vdslLineConfAdslOccupy TruthValue,
vdslLineConfApplicableStandard INTEGER, vdslLineConfApplicableStandard INTEGER,
vdslLineConfBandPlan INTEGER, vdslLineConfBandPlan INTEGER,
vdslLineConfBandPlanFx Unsigned32, vdslLineConfBandPlanFx Unsigned32,
vdslLineConfBandU0Usage INTEGER, vdslLineConfBandU0Usage INTEGER,
vdslLineConfUpstreamPsdTemplate INTEGER, vdslLineConfUpstreamPsdTemplate INTEGER,
vdslLineConfDownstreamPsdTemplate INTEGER, vdslLineConfDownstreamPsdTemplate INTEGER,
skipping to change at line 2084 skipping to change at page 41, line 20
default profile with an index of 1 MUST always default profile with an index of 1 MUST always
exist and its parameters will be set to vendor exist and its parameters will be set to vendor
specific values, unless otherwise specified in specific values, unless otherwise specified in
this document." this document."
::= { vdslLineConfProfileEntry 1 } ::= { vdslLineConfProfileEntry 1 }
vdslLineConfProfileName OBJECT-TYPE vdslLineConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32)) SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
Expires December 17, 2002 [PAGE 39]
DESCRIPTION DESCRIPTION
"The name for this profile as specified by a user." "The name for this profile as specified by a user."
::= { vdslLineConfProfileEntry 2 } ::= { vdslLineConfProfileEntry 2 }
vdslLineConfTargetSnrMgn OBJECT-TYPE vdslLineConfDownstreamMaxPwr OBJECT-TYPE
SYNTAX Unsigned32(0..310) SYNTAX Unsigned32 (0..58)
UNITS "0.25dB" UNITS "0.25dBm"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Configured Target Signal/Noise Margin. This is the "Specifies the maximum aggregate downstream power
Noise Margin the modems must achieve with a BER of 10-7 level in the range 0..14.5dBm."
or better to successfully complete initialization."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslLineConfProfileEntry 3 } ::= { vdslLineConfProfileEntry 3 }
vdslLineConfUpstreamTxSpeed OBJECT-TYPE vdslLineConfUpstreamMaxPwr OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32 (0..58)
UNITS "bits per second" UNITS "0.25dBm"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Upstream transmit speed for this line." "Specifies the maximum aggregate upstream power
level in the range 0..14.5dBm."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslLineConfProfileEntry 4 } ::= { vdslLineConfProfileEntry 4 }
vdslLineConfDownstreamTxSpeed OBJECT-TYPE vdslLineConfDownstreamMaxSnrMgn OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32 (0..127)
UNITS "bits per second" UNITS "0.25dBm"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Downstream transmit speed for this line." "Specifies the maximum downstream Signal/Noise Margin
in units of 0.25 dB, for a range of 0..31.75 dB."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslLineConfProfileEntry 5 } ::= { vdslLineConfProfileEntry 5 }
vdslLineConfDownstreamMinSnrMgn OBJECT-TYPE
SYNTAX Unsigned32 (0..127)
UNITS "0.25dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the minimum downstream Signal/Noise Margin
in units of 0.25 dB, for a range of 0..31.75 dB."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslLineConfProfileEntry 6 }
vdslLineConfDownstreamTargetSnrMgn OBJECT-TYPE
SYNTAX Unsigned32 (0..127)
UNITS "0.25dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the target downstream Signal/Noise Margin
in units of 0.25 dB, for a range of 0..31.75 dB.
This is the Noise Margin the modems must achieve with a
BER of 10-7 or better to successfully complete
initialization."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslLineConfProfileEntry 7 }
vdslLineConfUpstreamMaxSnrMgn OBJECT-TYPE
SYNTAX Unsigned32 (0..127)
UNITS "0.25dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the maximum upstream Signal/Noise Margin
in units of 0.25 dB, for a range of 0..31.75 dB."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslLineConfProfileEntry 8 }
vdslLineConfUpstreamMinSnrMgn OBJECT-TYPE
SYNTAX Unsigned32 (0..127)
UNITS "0.25dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the minimum upstream Signal/Noise Margin
in units of 0.25 dB, for a range of 0..31.75 dB."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslLineConfProfileEntry 9 }
vdslLineConfUpstreamTargetSnrMgn OBJECT-TYPE
SYNTAX Unsigned32 (0..127)
UNITS "0.25dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the target upstream Signal/Noise Margin in
units of 0.25 dB, for a range of 0..31.75 dB. This
is the Noise Margin the modems must achieve with a BER of
10-7 or better to successfully complete initialization."
REFERENCE "T1E1.4/2000-009R3" -- Part 1, common spec
::= { vdslLineConfProfileEntry 10 }
vdslLineConfDownstreamFastMaxDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the maximum downstream fast channel
data rate in steps of 1024 bits/second."
::= { vdslLineConfProfileEntry 11 }
vdslLineConfDownstreamFastMinDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the minimum downstream fast channel
data rate in steps of 1024 bits/second."
::= { vdslLineConfProfileEntry 12 }
vdslLineConfDownstreamSlowMaxDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the maximum downstream slow channel
data rate in steps of 1024 bits/second."
::= { vdslLineConfProfileEntry 13 }
vdslLineConfDownstreamSlowMinDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the minimum downstream slow channel
data rate in steps of 1024 bits/second."
::= { vdslLineConfProfileEntry 14 }
vdslLineConfUpstreamFastMaxDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the maximum upstream fast channel
data rate in steps of 1024 bits/second."
::= { vdslLineConfProfileEntry 15 }
vdslLineConfUpstreamFastMinDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the minimum upstream fast channel
data rate in steps of 1024 bits/second."
::= { vdslLineConfProfileEntry 16 }
vdslLineConfUpstreamSlowMaxDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the maximum upstream slow channel
data rate in steps of 1024 bits/second."
::= { vdslLineConfProfileEntry 17 }
vdslLineConfUpstreamSlowMinDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the minimum upstream slow channel
data rate in steps of 1024 bits/second."
::= { vdslLineConfProfileEntry 18 }
vdslLineConfRateAdaptationRatio OBJECT-TYPE
SYNTAX Unsigned32 (0..100)
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"For dynamic rate adaptation at startup, the allocation
of data rate in excess of the minimum data rate for each
channel is controlled by the object. This object specifies
the ratio of the allocation of the excess data rate between
the fast and the slow channels. This allocation represents
Fast Channel Allocation / Slow Channel Allocation."
::= { vdslLineConfProfileEntry 19 }
vdslLineConfUpstreamDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Aggregate upstream transmit speed for this line
in steps of 1024 bits/second."
::= { vdslLineConfProfileEntry 20 }
vdslLineConfDownstreamDataRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kbps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Aggregate downstream transmit speed for this line
in steps of 1024 bits/second."
::= { vdslLineConfProfileEntry 21 }
vdslLineConfDownstreamMaxInterDelay OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "ms"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the maximum interleave delay for the
downstream slow channel."
::= { vdslLineConfProfileEntry 22 }
vdslLineConfUpstreamMaxInterDelay OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "ms"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the maximum interleave delay for the
upstream slow channel."
::= { vdslLineConfProfileEntry 23 }
vdslLineConfUpstreamPboControl OBJECT-TYPE vdslLineConfUpstreamPboControl OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
disabled(1), disabled(1),
enabled(2) enabled(2)
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Upstream power backoff (PBO) control for this "Upstream power backoff (PBO) control for this
line. For modems which do not support upstream line. For modems which do not support upstream
PBO control, this object MUST be fixed at disabled(1)." PBO control, this object MUST be fixed at disabled(1)."
::= { vdslLineConfProfileEntry 6 } ::= { vdslLineConfProfileEntry 24 }
vdslLineConfDownstreamPboControl OBJECT-TYPE vdslLineConfDownstreamPboControl OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
disabled(1), disabled(1),
enabled(2) enabled(2)
Expires December 17, 2002 [PAGE 40]
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Downstream power backoff (PBO) control for this "Downstream power backoff (PBO) control for this
line. For modems which do not support downstream line. For modems which do not support downstream
PBO control, this object MUST be fixed at disabled(1)." PBO control, this object MUST be fixed at disabled(1)."
::= { vdslLineConfProfileEntry 7 } ::= { vdslLineConfProfileEntry 25 }
vdslLineConfDeploymentScenario OBJECT-TYPE vdslLineConfDeploymentScenario OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
fttCab(1), fttCab(1),
fttEx(2), fttEx(2),
other(3) other(3)
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The VDSL line deployment scenario. When using "The VDSL line deployment scenario. When using
fttCab(1), the VTU-C is located in a street cabinet. fttCab(1), the VTU-C is located in a street cabinet.
When using fttEx(2), the VTU-C is located at the When using fttEx(2), the VTU-C is located at the
central office." central office."
::= { vdslLineConfProfileEntry 8 } ::= { vdslLineConfProfileEntry 26 }
vdslLineConfAdslOccupy OBJECT-TYPE vdslLineConfAdslOccupy OBJECT-TYPE
SYNTAX TruthValue SYNTAX TruthValue
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Indicates if the VDSL line can occupy the ADSL "Indicates if the VDSL line can occupy the ADSL
frequency range." frequency range."
::= { vdslLineConfProfileEntry 9 } ::= { vdslLineConfProfileEntry 27 }
vdslLineConfApplicableStandard OBJECT-TYPE vdslLineConfApplicableStandard OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
ansi(1), ansi(1),
etsi(2), etsi(2),
itu(3), itu(3),
other(4) other(4)
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The VDSL standard to be used for the line." "The VDSL standard to be used for the line."
::= { vdslLineConfProfileEntry 10 } ::= { vdslLineConfProfileEntry 28 }
vdslLineConfBandPlan OBJECT-TYPE vdslLineConfBandPlan OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
bandPlan997(1), bandPlan997(1),
bandPlan998(2), bandPlan998(2),
Expires December 17, 2002 [PAGE 41]
bandPlanFx(3), bandPlanFx(3),
other(4) other(4)
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The VDSL band plan to be used for the line." "The VDSL band plan to be used for the line.
::= { vdslLineConfProfileEntry 11 }
bandPlan997(1) is to be used for
ITU-T G.993.1 Bandplan-B
ETSI Bandplan
ANSI Plan 997
bandPlan998(2) is to be used for
ITU-T G.993.1 Bandplan-A
ANSI Plan 998
bandPlanFx(3) is to be used for
ITU-T G.993.1 Bandplan-C.
other(4) is to be used for
non-standard bandplans.
If this object is set to bandPlanFx(3), then
the object vdslLineConfBandPlanFx MUST also be
set."
::= { vdslLineConfProfileEntry 29 }
vdslLineConfBandPlanFx OBJECT-TYPE vdslLineConfBandPlanFx OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32 (3750..12000)
UNITS "kHz" UNITS "kHz"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The frequency limit between bands D2 and U2 when "The frequency limit between bands D2 and U2 when
vdslLineConfBandPlan is set to bandPlanFx(3)." vdslLineConfBandPlan is set to bandPlanFx(3)."
::= { vdslLineConfProfileEntry 12 } ::= { vdslLineConfProfileEntry 30 }
vdslLineConfBandU0Usage OBJECT-TYPE vdslLineConfBandU0Usage OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
unused(1), unused(1),
upstream(2), upstream(2),
downstream(3) downstream(3)
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Defines the VDSL link use of the frequency range "Defines the VDSL link use of the frequency range
[25kHz - 138kHz] (U0)." [25kHz - 138kHz] (U0)."
::= { vdslLineConfProfileEntry 13 } ::= { vdslLineConfProfileEntry 31 }
vdslLineConfUpstreamPsdTemplate OBJECT-TYPE vdslLineConfUpstreamPsdTemplate OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
templateMask1(1), templateMask1(1),
templateMask2(2) templateMask2(2)
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The upstream PSD template to be used for the line." "The upstream PSD template to be used for the line."
::= { vdslLineConfProfileEntry 14 } ::= { vdslLineConfProfileEntry 32 }
vdslLineConfDownstreamPsdTemplate OBJECT-TYPE vdslLineConfDownstreamPsdTemplate OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
templateMask1(1), templateMask1(1),
templateMask2(2) templateMask2(2)
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
Expires December 17, 2002 [PAGE 42]
DESCRIPTION DESCRIPTION
"The downstream PSD template to be used for the line." "The downstream PSD template to be used for the line."
::= { vdslLineConfProfileEntry 15 } ::= { vdslLineConfProfileEntry 33 }
vdslLineConfProfileRowStatus OBJECT-TYPE vdslLineConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus SYNTAX RowStatus
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is used to create a new row or modify or "This object is used to create a new row or modify or
delete an existing row in this table. delete an existing row in this table.
A profile activated by setting this object to `active'. A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile. When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced `outOfService') it must be first unreferenced
from all associated lines." from all associated lines."
::= { vdslLineConfProfileEntry 16 } ::= { vdslLineConfProfileEntry 34 }
-- --
-- Multiple carrier modulation (MCM) configuration profile tables -- Multiple carrier modulation (MCM) configuration profile tables
-- --
vdslLineMCMConfProfileTable OBJECT-TYPE vdslLineMCMConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslLineMCMConfProfileEntry SYNTAX SEQUENCE OF VdslLineMCMConfProfileEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table contains information on the VDSL line "This table contains information on the VDSL line
configuration. One entry in this table reflects a configuration. One entry in this table reflects a
profile defined by a manager which can be used to profile defined by a manager which can be used to
configure the VDSL line. configure the VDSL line.
skipping to change at line 2305 skipping to change at page 49, line 33
DESCRIPTION DESCRIPTION
"Each entry consists of a list of parameters that "Each entry consists of a list of parameters that
represents the configuration of a multiple carrier represents the configuration of a multiple carrier
modulation VDSL modem. A default profile with an modulation VDSL modem. A default profile with an
index of 1 will always exist and its parameters will index of 1 will always exist and its parameters will
be set to vendor specific values, unless otherwise be set to vendor specific values, unless otherwise
specified in this document." specified in this document."
INDEX { vdslLineConfProfileIndex } INDEX { vdslLineConfProfileIndex }
::= { vdslLineMCMConfProfileTable 1 } ::= { vdslLineMCMConfProfileTable 1 }
Expires December 17, 2002 [PAGE 43]
VdslLineMCMConfProfileEntry ::= VdslLineMCMConfProfileEntry ::=
SEQUENCE SEQUENCE
{ {
vdslMCMConfProfileTxWindowLength Unsigned32, vdslMCMConfProfileTxWindowLength Unsigned32,
vdslMCMConfProfileRowStatus RowStatus vdslMCMConfProfileRowStatus RowStatus
} }
vdslMCMConfProfileTxWindowLength OBJECT-TYPE vdslMCMConfProfileTxWindowLength OBJECT-TYPE
SYNTAX Unsigned32(1..255) SYNTAX Unsigned32(1..255)
UNITS "samples" UNITS "samples"
skipping to change at line 2359 skipping to change at page 50, line 35
reflects the configuration for one of possibly many bands reflects the configuration for one of possibly many bands
with a multiple carrier modulation (MCM) VDSL line. with a multiple carrier modulation (MCM) VDSL line.
These entries are defined by a manager and can be used to These entries are defined by a manager and can be used to
configure the VDSL line. configure the VDSL line.
This table MUST be implemented for multiple carrier This table MUST be implemented for multiple carrier
modulation (MCM) VDSL lines. This table MUST NOT be modulation (MCM) VDSL lines. This table MUST NOT be
implemented for single carrier modulation VDSL lines." implemented for single carrier modulation VDSL lines."
::= { vdslMibObjects 13 } ::= { vdslMibObjects 13 }
Expires December 17, 2002 [PAGE 44]
vdslLineMCMConfProfileTxBandEntry OBJECT-TYPE vdslLineMCMConfProfileTxBandEntry OBJECT-TYPE
SYNTAX VdslLineMCMConfProfileTxBandEntry SYNTAX VdslLineMCMConfProfileTxBandEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Each entry consists of a transmit band descriptor, which "Each entry consists of a transmit band descriptor, which
is defined by a start and a stop tone index. is defined by a start and a stop tone index.
A default profile with an index of 1 will always exist and A default profile with an index of 1 will always exist and
its parameters will be set to vendor specific values, its parameters will be set to vendor specific values,
skipping to change at line 2412 skipping to change at page 51, line 35
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Stop tone index for this band." "Stop tone index for this band."
REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM
::= { vdslLineMCMConfProfileTxBandEntry 3 } ::= { vdslLineMCMConfProfileTxBandEntry 3 }
vdslMCMConfProfileTxBandRowStatus OBJECT-TYPE vdslMCMConfProfileTxBandRowStatus OBJECT-TYPE
SYNTAX RowStatus SYNTAX RowStatus
Expires December 17, 2002 [PAGE 45]
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is used to create a new row or modify or "This object is used to create a new row or modify or
delete an existing row in this table. delete an existing row in this table.
A profile activated by setting this object to `active'. A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile. When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of Before a profile can be deleted or taken out of
skipping to change at line 2467 skipping to change at page 52, line 36
INDEX { vdslLineConfProfileIndex, INDEX { vdslLineConfProfileIndex,
vdslMCMConfProfileRxBandNumber } vdslMCMConfProfileRxBandNumber }
::= { vdslLineMCMConfProfileRxBandTable 1 } ::= { vdslLineMCMConfProfileRxBandTable 1 }
VdslLineMCMConfProfileRxBandEntry ::= VdslLineMCMConfProfileRxBandEntry ::=
SEQUENCE SEQUENCE
{ {
vdslMCMConfProfileRxBandNumber Unsigned32, vdslMCMConfProfileRxBandNumber Unsigned32,
vdslMCMConfProfileRxBandStart Unsigned32, vdslMCMConfProfileRxBandStart Unsigned32,
vdslMCMConfProfileRxBandStop Unsigned32, vdslMCMConfProfileRxBandStop Unsigned32,
Expires December 17, 2002 [PAGE 46]
vdslMCMConfProfileRxBandRowStatus RowStatus vdslMCMConfProfileRxBandRowStatus RowStatus
} }
vdslMCMConfProfileRxBandNumber OBJECT-TYPE vdslMCMConfProfileRxBandNumber OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The index for this band descriptor entry." "The index for this band descriptor entry."
::= { vdslLineMCMConfProfileRxBandEntry 1 } ::= { vdslLineMCMConfProfileRxBandEntry 1 }
skipping to change at line 2522 skipping to change at page 53, line 37
from all associated lines." from all associated lines."
::= { vdslLineMCMConfProfileRxBandEntry 4 } ::= { vdslLineMCMConfProfileRxBandEntry 4 }
vdslLineMCMConfProfileTxPSDTable OBJECT-TYPE vdslLineMCMConfProfileTxPSDTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslLineMCMConfProfileTxPSDEntry SYNTAX SEQUENCE OF VdslLineMCMConfProfileTxPSDEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table contains transmit PSD mask descriptor "This table contains transmit PSD mask descriptor
configuration information for a VDSL line. Each entry in configuration information for a VDSL line. Each entry in
Expires December 17, 2002 [PAGE 47]
this table reflects the configuration for one tone within this table reflects the configuration for one tone within
a multiple carrier modulation (MCM) VDSL line. These a multiple carrier modulation (MCM) VDSL line. These
entries are defined by a manager and can be used to entries are defined by a manager and can be used to
configure the VDSL line. configure the VDSL line.
This table MUST be implemented for multiple carrier This table MUST be implemented for multiple carrier
modulation (MCM) VDSL lines. This table MUST NOT be modulation (MCM) VDSL lines. This table MUST NOT be
implemented for single carrier modulation VDSL lines." implemented for single carrier modulation VDSL lines."
::= { vdslMibObjects 15 } ::= { vdslMibObjects 15 }
skipping to change at line 2577 skipping to change at page 54, line 38
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The tone index for which the PSD is being specified." "The tone index for which the PSD is being specified."
REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM
::= { vdslLineMCMConfProfileTxPSDEntry 2 } ::= { vdslLineMCMConfProfileTxPSDEntry 2 }
vdslMCMConfProfileTxPSDPSD OBJECT-TYPE vdslMCMConfProfileTxPSDPSD OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
UNITS "0.5dBm"
Expires December 17, 2002 [PAGE 48]
UNITS "0.5dB"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Power Spectral Density level in steps of 0.5dB with "Power Spectral Density level in steps of 0.5dB with
an offset of -140dbm/Hz." an offset of -140dbm/Hz."
REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM
::= { vdslLineMCMConfProfileTxPSDEntry 3 } ::= { vdslLineMCMConfProfileTxPSDEntry 3 }
vdslMCMConfProfileTxPSDRowStatus OBJECT-TYPE vdslMCMConfProfileTxPSDRowStatus OBJECT-TYPE
SYNTAX RowStatus SYNTAX RowStatus
skipping to change at line 2632 skipping to change at page 55, line 40
vdslLineMCMConfProfileMaxTxPSDEntry OBJECT-TYPE vdslLineMCMConfProfileMaxTxPSDEntry OBJECT-TYPE
SYNTAX VdslLineMCMConfProfileMaxTxPSDEntry SYNTAX VdslLineMCMConfProfileMaxTxPSDEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Each entry consists of a transmit PSD mask descriptor, "Each entry consists of a transmit PSD mask descriptor,
which defines the maximum power spectral density (PSD) which defines the maximum power spectral density (PSD)
for a tone. for a tone.
A default profile with an index of 1 MUST always exist and A default profile with an index of 1 MUST always exist and
Expires December 17, 2002 [PAGE 49]
its parameters will be set to vendor specific values, its parameters will be set to vendor specific values,
unless otherwise specified in this document." unless otherwise specified in this document."
INDEX { vdslLineConfProfileIndex, INDEX { vdslLineConfProfileIndex,
vdslMCMConfProfileMaxTxPSDNumber } vdslMCMConfProfileMaxTxPSDNumber }
::= { vdslLineMCMConfProfileMaxTxPSDTable 1 } ::= { vdslLineMCMConfProfileMaxTxPSDTable 1 }
VdslLineMCMConfProfileMaxTxPSDEntry ::= VdslLineMCMConfProfileMaxTxPSDEntry ::=
SEQUENCE SEQUENCE
{ {
vdslMCMConfProfileMaxTxPSDNumber Unsigned32, vdslMCMConfProfileMaxTxPSDNumber Unsigned32,
skipping to change at line 2668 skipping to change at page 56, line 21
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The tone index for which the PSD is being specified." "The tone index for which the PSD is being specified."
REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM
::= { vdslLineMCMConfProfileMaxTxPSDEntry 2 } ::= { vdslLineMCMConfProfileMaxTxPSDEntry 2 }
vdslMCMConfProfileMaxTxPSDPSD OBJECT-TYPE vdslMCMConfProfileMaxTxPSDPSD OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
UNITS "0.5dB" UNITS "0.5dBm"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Power Spectral Density level in steps of 0.5dB with "Power Spectral Density level in steps of 0.5dB with
an offset of -140dbm/Hz." an offset of -140dbm/Hz."
REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM
::= { vdslLineMCMConfProfileMaxTxPSDEntry 3 } ::= { vdslLineMCMConfProfileMaxTxPSDEntry 3 }
vdslMCMConfProfileMaxTxPSDRowStatus OBJECT-TYPE vdslMCMConfProfileMaxTxPSDRowStatus OBJECT-TYPE
SYNTAX RowStatus SYNTAX RowStatus
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is used to create a new row or modify or "This object is used to create a new row or modify or
delete an existing row in this table. delete an existing row in this table.
A profile activated by setting this object to `active'. A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile. When `active' is set, the system will validate the profile.
Expires December 17, 2002 [PAGE 50]
Before a profile can be deleted or taken out of Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced `outOfService') it must be first unreferenced
from all associated lines." from all associated lines."
::= { vdslLineMCMConfProfileMaxTxPSDEntry 4 } ::= { vdslLineMCMConfProfileMaxTxPSDEntry 4 }
vdslLineMCMConfProfileMaxRxPSDTable OBJECT-TYPE vdslLineMCMConfProfileMaxRxPSDTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslLineMCMConfProfileMaxRxPSDEntry SYNTAX SEQUENCE OF VdslLineMCMConfProfileMaxRxPSDEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
skipping to change at line 2741 skipping to change at page 57, line 41
vdslMCMConfProfileMaxRxPSDNumber Unsigned32, vdslMCMConfProfileMaxRxPSDNumber Unsigned32,
vdslMCMConfProfileMaxRxPSDTone Unsigned32, vdslMCMConfProfileMaxRxPSDTone Unsigned32,
vdslMCMConfProfileMaxRxPSDPSD Unsigned32, vdslMCMConfProfileMaxRxPSDPSD Unsigned32,
vdslMCMConfProfileMaxRxPSDRowStatus RowStatus vdslMCMConfProfileMaxRxPSDRowStatus RowStatus
} }
vdslMCMConfProfileMaxRxPSDNumber OBJECT-TYPE vdslMCMConfProfileMaxRxPSDNumber OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
Expires December 17, 2002 [PAGE 51]
DESCRIPTION DESCRIPTION
"The index for this band descriptor entry." "The index for this band descriptor entry."
::= { vdslLineMCMConfProfileMaxRxPSDEntry 1 } ::= { vdslLineMCMConfProfileMaxRxPSDEntry 1 }
vdslMCMConfProfileMaxRxPSDTone OBJECT-TYPE vdslMCMConfProfileMaxRxPSDTone OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The tone index for which the PSD is being specified." "The tone index for which the PSD is being specified."
REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM
::= { vdslLineMCMConfProfileMaxRxPSDEntry 2 } ::= { vdslLineMCMConfProfileMaxRxPSDEntry 2 }
vdslMCMConfProfileMaxRxPSDPSD OBJECT-TYPE vdslMCMConfProfileMaxRxPSDPSD OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
UNITS "0.5dB" UNITS "0.5dBm"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Power Spectral Density level in steps of 0.5dB with "Power Spectral Density level in steps of 0.5dB with
an offset of -140dbm/Hz." an offset of -140dbm/Hz."
REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM REFERENCE "T1E1.4/2000-013R4" -- Part 3, MCM
::= { vdslLineMCMConfProfileMaxRxPSDEntry 3 } ::= { vdslLineMCMConfProfileMaxRxPSDEntry 3 }
vdslMCMConfProfileMaxRxPSDRowStatus OBJECT-TYPE vdslMCMConfProfileMaxRxPSDRowStatus OBJECT-TYPE
SYNTAX RowStatus SYNTAX RowStatus
skipping to change at line 2796 skipping to change at page 58, line 42
-- --
vdslLineSCMConfProfileTable OBJECT-TYPE vdslLineSCMConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslLineSCMConfProfileEntry SYNTAX SEQUENCE OF VdslLineSCMConfProfileEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table contains information on the VDSL line "This table contains information on the VDSL line
configuration. One entry in this table reflects a configuration. One entry in this table reflects a
profile defined by a manager which can be used to profile defined by a manager which can be used to
Expires December 17, 2002 [PAGE 52]
configure the VDSL line. configure the VDSL line.
This table MUST be implemented for single carrier This table MUST be implemented for single carrier
modulation (SCM) VDSL lines. This table MUST NOT be modulation (SCM) VDSL lines. This table MUST NOT be
implemented for multiple carrier modulation (MCM) VDSL implemented for multiple carrier modulation (MCM) VDSL
lines." lines."
::= { vdslMibObjects 18 } ::= { vdslMibObjects 18 }
vdslLineSCMConfProfileEntry OBJECT-TYPE vdslLineSCMConfProfileEntry OBJECT-TYPE
SYNTAX VdslLineSCMConfProfileEntry SYNTAX VdslLineSCMConfProfileEntry
skipping to change at line 2824 skipping to change at page 59, line 16
A default profile with an index of 1 MUST always exist and A default profile with an index of 1 MUST always exist and
its parameters will be set to vendor specific values, its parameters will be set to vendor specific values,
unless otherwise specified in this document." unless otherwise specified in this document."
INDEX { vdslLineConfProfileIndex } INDEX { vdslLineConfProfileIndex }
::= { vdslLineSCMConfProfileTable 1 } ::= { vdslLineSCMConfProfileTable 1 }
VdslLineSCMConfProfileEntry ::= VdslLineSCMConfProfileEntry ::=
SEQUENCE SEQUENCE
{ {
vdslSCMConfProfileInterleaveDepth Unsigned32, vdslSCMConfProfileDownInterleaveDepth Unsigned32,
vdslSCMConfProfileFastCodewordSize Unsigned32, vdslSCMConfProfileUpInterleaveDepth Unsigned32,
vdslSCMConfProfileDownNumCarriers INTEGER,
vdslSCMConfProfileUpNumCarriers INTEGER,
vdslSCMConfProfileDownFastCodewordSize Unsigned32,
vdslSCMConfProfileUpFastCodewordSize Unsigned32,
vdslSCMConfProfileTransmitPSDMask BITS, vdslSCMConfProfileTransmitPSDMask BITS,
vdslSCMConfProfileBands INTEGER, vdslSCMConfProfileVendorNotch1Start Unsigned32,
vdslSCMConfProfileFastFecSize INTEGER, vdslSCMConfProfileVendorNotch1Stop Unsigned32,
vdslSCMConfProfileVendorNotch2Start Unsigned32,
vdslSCMConfProfileVendorNotch2Stop Unsigned32,
vdslSCMConfProfileDownFastFecSize INTEGER,
vdslSCMConfProfileUpFastFecSize INTEGER,
vdslSCMConfProfileDownSlowBlockSize INTEGER,
vdslSCMConfProfileUpSlowBlockSize INTEGER,
vdslSCMConfProfileRowStatus RowStatus vdslSCMConfProfileRowStatus RowStatus
} }
vdslSCMConfProfileInterleaveDepth OBJECT-TYPE vdslSCMConfProfileDownInterleaveDepth OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32 (0..64)
UNITS "octets"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Specifies the interleaving depth." "Specifies the downstream interleaving depth."
REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM
::= { vdslLineSCMConfProfileEntry 1 } ::= { vdslLineSCMConfProfileEntry 1 }
vdslSCMConfProfileFastCodewordSize OBJECT-TYPE vdslSCMConfProfileUpInterleaveDepth OBJECT-TYPE
SYNTAX Unsigned32 (0..64)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the upstream interleaving depth."
REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM
::= { vdslLineSCMConfProfileEntry 2 }
vdslSCMConfProfileDownNumCarriers OBJECT-TYPE
SYNTAX INTEGER
{
oneCarrier(1),
twoCarriers(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the number of downstream carriers."
REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM
::= { vdslLineSCMConfProfileEntry 3 }
vdslSCMConfProfileUpNumCarriers OBJECT-TYPE
SYNTAX INTEGER
{
oneCarrier(1),
twoCarriers(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the number of upstream carriers."
REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM
::= { vdslLineSCMConfProfileEntry 4 }
vdslSCMConfProfileDownFastCodewordSize OBJECT-TYPE
SYNTAX Unsigned32(0..180) SYNTAX Unsigned32(0..180)
UNITS "octets" UNITS "octets"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Specifies the length in octets of the fast codeword. "Specifies the length in octets of the downstream
A value of 0 indicates that the single latency transport fast codeword. A value of 0 indicates that the
class is to be utilized." single latency transport class is to be utilized."
REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM
::= { vdslLineSCMConfProfileEntry 5 }
Expires December 17, 2002 [PAGE 53] vdslSCMConfProfileUpFastCodewordSize OBJECT-TYPE
SYNTAX Unsigned32 (0..180)
UNITS "octets"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the length in octets of the upstream
fast codeword. A value of 0 indicates that the
single latency transport class is to be utilized."
REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM
::= { vdslLineSCMConfProfileEntry 2 } ::= { vdslLineSCMConfProfileEntry 6 }
vdslSCMConfProfileTransmitPSDMask OBJECT-TYPE vdslSCMConfProfileTransmitPSDMask OBJECT-TYPE
SYNTAX BITS SYNTAX BITS
{ {
vendorNotch1(0), -- vendor specific notch vendorNotch1(0), -- vendor specific notch
vendorNotch2(1), -- vendor specific notch vendorNotch2(1), -- vendor specific notch
amateurBand30m(2), -- amateur radio band notch amateurBand30m(2), -- amateur radio band notch
amateurBand40m(3), -- amateur radio band notch amateurBand40m(3), -- amateur radio band notch
amateurBand80m(4), -- amateur radio band notch amateurBand80m(4), -- amateur radio band notch
amateurBand160m(5) -- amateur radio band notch amateurBand160m(5) -- amateur radio band notch
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The transmit power spectral density mask code." "The transmit power spectral density mask code.
Amateur radio band notching is defined in the VDSL
spectrum as follows:
Band Start Frequency Stop Frequecy
---- ------------------ --------------------------------
30m 1810 kHz 2000 kHz
40m 3500 kHz 3800 kHz (ETSI); 4000 kHz (ANSI)
80m 7000 kHz 7100 kHz (ETSI); 7300 kHz (ANSI)
160m 10100 kHz 10150 kHz
Notching for each standard band can be enabled or disabled
via the bit mask.
Two custom, or vendor specific, notches may be specified.
If either of these are enabled via the bit mask, then the
following objects MUST be specified:
If vendorNotch1 is enabled, then both
vdslSCMConfProfileVendorNotch1Start
vdslSCMConfProfileVendorNotch1Stop
MUST be specified.
If vendorNotch2 is enabled, then both
vdslSCMConfProfileVendorNotch2Start
vdslSCMConfProfileVendorNotch2Stop
MUST be specified."
REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM
::= { vdslLineSCMConfProfileEntry 3 } ::= { vdslLineSCMConfProfileEntry 7 }
vdslSCMConfProfileBands OBJECT-TYPE vdslSCMConfProfileVendorNotch1Start OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kHz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the start frequency of the vendor-specific
amateur radio notch 1."
REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM
::= { vdslLineSCMConfProfileEntry 8 }
vdslSCMConfProfileVendorNotch1Stop OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kHz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the stop frequency of the vendor-specific
amateur radio notch 1."
REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM
::= { vdslLineSCMConfProfileEntry 9 }
vdslSCMConfProfileVendorNotch2Start OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kHz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the start frequency of the vendor-specific
amateur radio notch 2."
REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM
::= { vdslLineSCMConfProfileEntry 10 }
vdslSCMConfProfileVendorNotch2Stop OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kHz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the stop frequency of the vendor-specific
amateur radio notch 2."
REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM
::= { vdslLineSCMConfProfileEntry 11 }
vdslSCMConfProfileDownFastFecSize OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
oneBand(1), noFEC(1),
twoBands(2), fecSize2(2),
upstreamU0(3) fecSize4(3),
fecSize16(4)
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Specifies the number of bands used to transmit." "When fast channel is being used, this object specifies
the size of the downstream forward error correction (FEC)
codeword."
REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM
::= { vdslLineSCMConfProfileEntry 4 } ::= { vdslLineSCMConfProfileEntry 12 }
vdslSCMConfProfileFastFecSize OBJECT-TYPE vdslSCMConfProfileUpFastFecSize OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
noFEC(1), noFEC(1),
fecSize2(2), fecSize2(2),
fecSize4(3), fecSize4(3),
fecSize16(4) fecSize16(4)
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"When fast channel is being used, this object specifies "When fast channel is being used, this object specifies
the size of the forward error correction (FEC) codeword." the size of the upstream forward error correction (FEC)
codeword."
REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM
::= { vdslLineSCMConfProfileEntry 5 } ::= { vdslLineSCMConfProfileEntry 13 }
vdslSCMConfProfileDownSlowBlockSize OBJECT-TYPE
SYNTAX INTEGER
{
s8(1),
s4(2),
s2(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the downstream slow channel interleaved
block size. Options are s/8, s/4, or s/2."
REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM
::= { vdslLineSCMConfProfileEntry 14 }
vdslSCMConfProfileUpSlowBlockSize OBJECT-TYPE
SYNTAX INTEGER
{
s8(1),
s4(2),
s2(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the upstream slow channel interleaved
block size. Options are s/8, s/4, or s/2."
REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM
::= { vdslLineSCMConfProfileEntry 15 }
vdslSCMConfProfileRowStatus OBJECT-TYPE vdslSCMConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus SYNTAX RowStatus
MAX-ACCESS read-create MAX-ACCESS read-create
Expires December 17, 2002 [PAGE 54]
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is used to create a new row or modify or "This object is used to create a new row or modify or
delete an existing row in this table. delete an existing row in this table.
A profile activated by setting this object to `active'. A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile. When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced `outOfService') it must be first unreferenced
from all associated lines." from all associated lines."
::= { vdslLineSCMConfProfileEntry 6 } ::= { vdslLineSCMConfProfileEntry 16 }
vdslLineSCMConfProfileTxBandTable OBJECT-TYPE vdslLineSCMConfProfileTxBandTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslLineSCMConfProfileTxBandEntry SYNTAX SEQUENCE OF VdslLineSCMConfProfileTxBandEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This table contains transmit band descriptor configuration "This table contains transmit band descriptor configuration
information for a VDSL line. Each entry in this table information for a VDSL line. Each entry in this table
reflects the configuration for one of possibly three bands reflects the configuration for one of possibly three bands
with a single carrier modulation (SCM) VDSL line. These with a single carrier modulation (SCM) VDSL line. These
skipping to change at line 2953 skipping to change at page 64, line 42
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Each entry consists of a list of parameters that "Each entry consists of a list of parameters that
represents the configuration of a single carrier represents the configuration of a single carrier
modulation VDSL modem transmit band. modulation VDSL modem transmit band.
A default profile with an index of 1 MUST always exist and A default profile with an index of 1 MUST always exist and
its parameters will be set to vendor specific values, its parameters will be set to vendor specific values,
unless otherwise specified in this document." unless otherwise specified in this document."
INDEX { vdslLineConfProfileIndex, INDEX { vdslLineConfProfileIndex,
vdslSCMConfProfileTxBandSide,
vdslSCMConfProfileTxBandNumber } vdslSCMConfProfileTxBandNumber }
::= { vdslLineSCMConfProfileTxBandTable 1 } ::= { vdslLineSCMConfProfileTxBandTable 1 }
VdslLineSCMConfProfileTxBandEntry ::= VdslLineSCMConfProfileTxBandEntry ::=
SEQUENCE SEQUENCE
{ {
vdslSCMConfProfileTxBandSide VdslLineEntity,
vdslSCMConfProfileTxBandNumber INTEGER, vdslSCMConfProfileTxBandNumber INTEGER,
vdslSCMConfProfileTxBandTransmitPSDLevel Unsigned32, vdslSCMConfProfileTxBandTransmitPSDLevel Unsigned32,
Expires December 17, 2002 [PAGE 55]
vdslSCMConfProfileTxBandSymbolRateProfile Unsigned32, vdslSCMConfProfileTxBandSymbolRateProfile Unsigned32,
vdslSCMConfProfileTxBandConstellationSize Unsigned32, vdslSCMConfProfileTxBandConstellationSize Unsigned32,
vdslSCMConfProfileTxBandCenterFrequency Unsigned32, vdslSCMConfProfileTxBandCenterFrequency Unsigned32,
vdslSCMConfProfileTxBandRowStatus RowStatus vdslSCMConfProfileTxBandRowStatus RowStatus
} }
vdslSCMConfProfileTxBandSide OBJECT-TYPE
SYNTAX VdslLineEntity
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Identifies whether this band entry describes
downstream or upstream transmission."
::= { vdslLineSCMConfProfileTxBandEntry 1 }
vdslSCMConfProfileTxBandNumber OBJECT-TYPE vdslSCMConfProfileTxBandNumber OBJECT-TYPE
SYNTAX INTEGER SYNTAX INTEGER
{ {
band1(1), band1(1),
band2(2), band2(2),
upstreamU0(3) upstreamU0(3)
} }
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The SCN transmit band number for this entry." "The SCN transmit band number for this entry."
::= { vdslLineSCMConfProfileTxBandEntry 1 } ::= { vdslLineSCMConfProfileTxBandEntry 2 }
vdslSCMConfProfileTxBandTransmitPSDLevel OBJECT-TYPE vdslSCMConfProfileTxBandTransmitPSDLevel OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
UNITS "-dBm/Hz" UNITS "-dBm/Hz"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The transmit power spectral density for the VDSL modem." "The transmit power spectral density for the VDSL modem."
REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM
::= { vdslLineSCMConfProfileTxBandEntry 2 } ::= { vdslLineSCMConfProfileTxBandEntry 3 }
vdslSCMConfProfileTxBandSymbolRateProfile OBJECT-TYPE vdslSCMConfProfileTxBandSymbolRateProfile OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
UNITS "kbaud" UNITS "kbaud"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The symbol rate profile calculated as S = SR/BSR, where "The symbol rate profile calculated as S = SR/BSR, where
SR is the required symbol rate in kbaud, BSR = 67.5." SR is the required symbol rate in kbaud, BSR = 67.5."
REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM
::= { vdslLineSCMConfProfileTxBandEntry 3 } ::= { vdslLineSCMConfProfileTxBandEntry 4 }
vdslSCMConfProfileTxBandConstellationSize OBJECT-TYPE vdslSCMConfProfileTxBandConstellationSize OBJECT-TYPE
SYNTAX Unsigned32(0..8) SYNTAX Unsigned32(0..8)
UNITS "log2" UNITS "log2"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Specifies the constellation size." "Specifies the constellation size."
REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM
::= { vdslLineSCMConfProfileTxBandEntry 4 } ::= { vdslLineSCMConfProfileTxBandEntry 5 }
vdslSCMConfProfileTxBandCenterFrequency OBJECT-TYPE vdslSCMConfProfileTxBandCenterFrequency OBJECT-TYPE
SYNTAX Unsigned32(0..511) SYNTAX Unsigned32(0..511)
UNITS "33.75kHz" UNITS "33.75kHz"
Expires December 17, 2002 [PAGE 56]
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Specifies the center frequency profile K." "Specifies the center frequency profile K."
REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM REFERENCE "T1E1.4/2000-011R3" -- Part 2, SCM
::= { vdslLineSCMConfProfileTxBandEntry 5 } ::= { vdslLineSCMConfProfileTxBandEntry 6 }
vdslSCMConfProfileTxBandRowStatus OBJECT-TYPE vdslSCMConfProfileTxBandRowStatus OBJECT-TYPE
SYNTAX RowStatus SYNTAX RowStatus
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is used to create a new row or modify or "This object is used to create a new row or modify or
delete an existing row in this table. delete an existing row in this table.
A profile activated by setting this object to `active'. A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile. When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced `outOfService') it must be first unreferenced
from all associated lines." from all associated lines."
::= { vdslLineSCMConfProfileTxBandEntry 6 } ::= { vdslLineSCMConfProfileTxBandEntry 7 }
-- --
-- Alarm configuration profile table -- Alarm configuration profile table
-- --
vdslLineAlarmConfProfileTable OBJECT-TYPE vdslLineAlarmConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF VdslLineAlarmConfProfileEntry SYNTAX SEQUENCE OF VdslLineAlarmConfProfileEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
skipping to change at line 3072 skipping to change at page 67, line 12
"Each entry consists of a list of parameters that "Each entry consists of a list of parameters that
represents the configuration of a VDSL line alarm represents the configuration of a VDSL line alarm
profile. profile.
A default profile with an index of 1 MUST always exist and A default profile with an index of 1 MUST always exist and
its parameters will be set to vendor specific values, its parameters will be set to vendor specific values,
unless otherwise specified in this document." unless otherwise specified in this document."
INDEX { vdslLineAlarmConfProfileIndex } INDEX { vdslLineAlarmConfProfileIndex }
::= { vdslLineAlarmConfProfileTable 1 } ::= { vdslLineAlarmConfProfileTable 1 }
Expires December 17, 2002 [PAGE 57]
VdslLineAlarmConfProfileEntry ::= VdslLineAlarmConfProfileEntry ::=
SEQUENCE SEQUENCE
{ {
vdslLineAlarmConfProfileIndex Unsigned32, vdslLineAlarmConfProfileIndex Unsigned32,
vdslLineAlarmConfProfileName SnmpAdminString, vdslLineAlarmConfProfileName SnmpAdminString,
vdslThresh15MinLofs Unsigned32, vdslThresh15MinLofs HCPerfIntervalThreshold,
vdslThresh15MinLoss Unsigned32, vdslThresh15MinLoss HCPerfIntervalThreshold,
vdslThresh15MinLprs Unsigned32, vdslThresh15MinLprs HCPerfIntervalThreshold,
vdslThresh15MinESs Unsigned32, vdslThresh15MinESs HCPerfIntervalThreshold,
vdslThresh15MinSESs Unsigned32, vdslThresh15MinSESs HCPerfIntervalThreshold,
vdslThresh15MinUASs Unsigned32, vdslThresh15MinUASs HCPerfIntervalThreshold,
vdslInitFailureNotificationEnable TruthValue, vdslInitFailureNotificationEnable TruthValue,
vdslLineAlarmConfProfileRowStatus RowStatus vdslLineAlarmConfProfileRowStatus RowStatus
} }
vdslLineAlarmConfProfileIndex OBJECT-TYPE vdslLineAlarmConfProfileIndex OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object is used by the line alarm configuration table "This object is used by the line alarm configuration table
skipping to change at line 3107 skipping to change at page 67, line 46
vdslLineAlarmConfProfileName OBJECT-TYPE vdslLineAlarmConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32)) SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The name for this profile as specified by a user." "The name for this profile as specified by a user."
::= { vdslLineAlarmConfProfileEntry 2 } ::= { vdslLineAlarmConfProfileEntry 2 }
vdslThresh15MinLofs OBJECT-TYPE vdslThresh15MinLofs OBJECT-TYPE
SYNTAX Unsigned32(0..899) SYNTAX HCPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the threshold for the number of "This object configures the threshold for the number of
loss of frame seconds (lofs) within any given 15-minute loss of frame seconds (lofs) within any given 15-minute
performance data collection interval. If the value of performance data collection interval. If the value of
loss of frame seconds in a particular 15-minute collection loss of frame seconds in a particular 15-minute collection
interval reaches/exceeds this value, a interval reaches/exceeds this value, a
vdslPerfLofsThreshNotification notification will be vdslPerfLofsThreshNotification notification will be
generated. No more than one notification will be sent generated. No more than one notification will be sent
per interval." per interval."
::= { vdslLineAlarmConfProfileEntry 3 } ::= { vdslLineAlarmConfProfileEntry 3 }
vdslThresh15MinLoss OBJECT-TYPE vdslThresh15MinLoss OBJECT-TYPE
SYNTAX Unsigned32(0..899) SYNTAX HCPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
Expires December 17, 2002 [PAGE 58]
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the threshold for the number of "This object configures the threshold for the number of
loss of signal seconds (loss) within any given 15-minute loss of signal seconds (loss) within any given 15-minute
performance data collection interval. If the value of performance data collection interval. If the value of
loss of frame seconds in a particular 15-minute collection loss of frame seconds in a particular 15-minute collection
interval reaches/exceeds this value, a interval reaches/exceeds this value, a
vdslPerfLossThreshNotification notification will be vdslPerfLossThreshNotification notification will be
generated. One notification will be sent per interval generated. One notification will be sent per interval
per endpoint." per endpoint."
::= { vdslLineAlarmConfProfileEntry 4 } ::= { vdslLineAlarmConfProfileEntry 4 }
vdslThresh15MinLprs OBJECT-TYPE vdslThresh15MinLprs OBJECT-TYPE
SYNTAX Unsigned32(0..899) SYNTAX HCPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the threshold for the number of "This object configures the threshold for the number of
loss of power seconds (lprs) within any given 15-minute loss of power seconds (lprs) within any given 15-minute
performance data collection interval. If the value of performance data collection interval. If the value of
loss of frame seconds in a particular 15-minute collection loss of frame seconds in a particular 15-minute collection
interval reaches/exceeds this value, a interval reaches/exceeds this value, a
vdslPerfLprsThreshNotification notification will be vdslPerfLprsThreshNotification notification will be
generated. No more than one notification will be sent generated. No more than one notification will be sent
per interval." per interval."
::= { vdslLineAlarmConfProfileEntry 5 } ::= { vdslLineAlarmConfProfileEntry 5 }
vdslThresh15MinESs OBJECT-TYPE vdslThresh15MinESs OBJECT-TYPE
SYNTAX Unsigned32(0..899) SYNTAX HCPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the threshold for the number of "This object configures the threshold for the number of
errored seconds (ESs) within any given 15-minute errored seconds (ESs) within any given 15-minute
performance data collection interval. If the value of performance data collection interval. If the value of
errored seconds in a particular 15-minute collection errored seconds in a particular 15-minute collection
interval reaches/exceeds this value, a interval reaches/exceeds this value, a
vdslPerfESsThreshNotification notification will be vdslPerfESsThreshNotification notification will be
skipping to change at line 3171 skipping to change at page 69, line 4
DESCRIPTION DESCRIPTION
"This object configures the threshold for the number of "This object configures the threshold for the number of
errored seconds (ESs) within any given 15-minute errored seconds (ESs) within any given 15-minute
performance data collection interval. If the value of performance data collection interval. If the value of
errored seconds in a particular 15-minute collection errored seconds in a particular 15-minute collection
interval reaches/exceeds this value, a interval reaches/exceeds this value, a
vdslPerfESsThreshNotification notification will be vdslPerfESsThreshNotification notification will be
generated. No more than one notification will be sent generated. No more than one notification will be sent
per interval." per interval."
::= { vdslLineAlarmConfProfileEntry 6 } ::= { vdslLineAlarmConfProfileEntry 6 }
vdslThresh15MinSESs OBJECT-TYPE vdslThresh15MinSESs OBJECT-TYPE
SYNTAX Unsigned32(0..899) SYNTAX HCPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the threshold for the number of "This object configures the threshold for the number of
severely errored seconds (SESs) within any given 15-minute severely errored seconds (SESs) within any given 15-minute
Expires December 17, 2002 [PAGE 59]
performance data collection interval. If the value of performance data collection interval. If the value of
severely errored seconds in a particular 15-minute severely errored seconds in a particular 15-minute
collection interval reaches/exceeds this value, a collection interval reaches/exceeds this value, a
vdslPerfSESsThreshNotification notification will be vdslPerfSESsThreshNotification notification will be
generated. No more than one notification will be sent generated. No more than one notification will be sent
per interval." per interval."
::= { vdslLineAlarmConfProfileEntry 7 } ::= { vdslLineAlarmConfProfileEntry 7 }
vdslThresh15MinUASs OBJECT-TYPE vdslThresh15MinUASs OBJECT-TYPE
SYNTAX Unsigned32(0..899) SYNTAX HCPerfIntervalThreshold
UNITS "seconds" UNITS "seconds"
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object configures the threshold for the number of "This object configures the threshold for the number of
unavailable seconds (UASs) within any given 15-minute unavailable seconds (UASs) within any given 15-minute
performance data collection interval. If the value of performance data collection interval. If the value of
unavailable seconds in a particular 15-minute collection unavailable seconds in a particular 15-minute collection
interval reaches/exceeds this value, a interval reaches/exceeds this value, a
vdslPerfUASsThreshNotification notification will be vdslPerfUASsThreshNotification notification will be
skipping to change at line 3235 skipping to change at page 70, line 15
When `active' is set, the system will validate the profile. When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced `outOfService') it must be first unreferenced
from all associated lines." from all associated lines."
::= { vdslLineAlarmConfProfileEntry 10 } ::= { vdslLineAlarmConfProfileEntry 10 }
-- Notification definitions -- Notification definitions
Expires December 17, 2002 [PAGE 60]
vdslNotifications OBJECT IDENTIFIER ::= { vdslLineMib 0 } vdslNotifications OBJECT IDENTIFIER ::= { vdslLineMib 0 }
vdslPerfLofsThreshNotification NOTIFICATION-TYPE vdslPerfLofsThreshNotification NOTIFICATION-TYPE
OBJECTS { OBJECTS {
vdslPerfCurr15MinLofs, vdslPerfCurr15MinLofs,
vdslThresh15MinLofs vdslThresh15MinLofs
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Loss of Framing 15-minute interval threshold reached." "Loss of Framing 15-minute interval threshold reached."
skipping to change at line 3289 skipping to change at page 71, line 15
OBJECTS { OBJECTS {
vdslPerfCurr15MinSESs, vdslPerfCurr15MinSESs,
vdslThresh15MinSESs vdslThresh15MinSESs
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Severely Errored Seconds 15-minute interval threshold "Severely Errored Seconds 15-minute interval threshold
reached." reached."
::= { vdslNotifications 5 } ::= { vdslNotifications 5 }
Expires December 17, 2002 [PAGE 61]
vdslPerfUASsThreshNotification NOTIFICATION-TYPE vdslPerfUASsThreshNotification NOTIFICATION-TYPE
OBJECTS { OBJECTS {
vdslPerfCurr15MinUASs, vdslPerfCurr15MinUASs,
vdslThresh15MinUASs vdslThresh15MinUASs
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Unavailable Seconds 15-minute interval threshold reached." "Unavailable Seconds 15-minute interval threshold reached."
::= { vdslNotifications 6 } ::= { vdslNotifications 6 }
vdslDownMaxSnrMgnExceededNotification NOTIFICATION-TYPE
OBJECTS {
vdslCurrSnrMgn,
vdslLineConfDownstreamMaxSnrMgn
}
STATUS current
DESCRIPTION
"The downstream Signal to Noise Margin exceeded
vdslLineConfDownstreamMaxSnrMgn. The object
vdslCurrSnrMgn will contain the Signal to Noise
margin as measured by the VTU-R."
::= { vdslNotifications 7 }
vdslDownMinSnrMgnExceededNotification NOTIFICATION-TYPE
OBJECTS {
vdslCurrSnrMgn,
vdslLineConfDownstreamMinSnrMgn
}
STATUS current
DESCRIPTION
"The downstream Signal to Noise Margin fell below
vdslLineConfDownstreamMinSnrMgn. The object
vdslCurrSnrMgn will contain the Signal to Noise
margin as measured by the VTU-R."
::= { vdslNotifications 8 }
vdslUpMaxSnrMgnExceededNotification NOTIFICATION-TYPE
OBJECTS {
vdslCurrSnrMgn,
vdslLineConfUpstreamMaxSnrMgn
}
STATUS current
DESCRIPTION
"The upstream Signal to Noise Margin exceeded
vdslLineConfDownstreamMaxSnrMgn. The object
vdslCurrSnrMgn will contain the Signal to Noise
margin as measured by the VTU-C."
::= { vdslNotifications 9 }
vdslUpMinSnrMgnExceededNotification NOTIFICATION-TYPE
OBJECTS {
vdslCurrSnrMgn,
vdslLineConfUpstreamMinSnrMgn
}
STATUS current
DESCRIPTION
"The upstream Signal to Noise Margin fell below
vdslLineConfDownstreamMinSnrMgn. The object
vdslCurrSnrMgn will contain the Signal to Noise
margin as measured by the VTU-C."
::= { vdslNotifications 10 }
vdslInitFailureNotification NOTIFICATION-TYPE vdslInitFailureNotification NOTIFICATION-TYPE
OBJECTS { OBJECTS {
vdslCurrStatus vdslCurrStatus
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Vtu initialization failed. See vdslCurrStatus for "Vtu initialization failed. See vdslCurrStatus for
potential reasons." potential reasons."
::= { vdslNotifications 7 } ::= { vdslNotifications 11 }
-- conformance information -- conformance information
vdslConformance OBJECT IDENTIFIER ::= { vdslLineMib 3 } vdslConformance OBJECT IDENTIFIER ::= { vdslLineMib 3 }
vdslGroups OBJECT IDENTIFIER ::= { vdslConformance 1 } vdslGroups OBJECT IDENTIFIER ::= { vdslConformance 1 }
vdslCompliances OBJECT IDENTIFIER ::= { vdslConformance 2 } vdslCompliances OBJECT IDENTIFIER ::= { vdslConformance 2 }
vdslLineMibCompliance MODULE-COMPLIANCE vdslLineMibCompliance MODULE-COMPLIANCE
STATUS current STATUS current
DESCRIPTION DESCRIPTION
skipping to change at line 3343 skipping to change at page 73, line 16
This group should not be implemented for VDSL lines This group should not be implemented for VDSL lines
which utilize single carrier modulation." which utilize single carrier modulation."
GROUP vdslSCMGroup GROUP vdslSCMGroup
DESCRIPTION DESCRIPTION
"This group is mandatory for VDSL lines which "This group is mandatory for VDSL lines which
utilize single carrier modulation. utilize single carrier modulation.
This group should not be implemented for VDSL lines This group should not be implemented for VDSL lines
which utilize multiple carrier modulation" which utilize multiple carrier modulation"
Expires December 17, 2002 [PAGE 62]
::= { vdslCompliances 1 } ::= { vdslCompliances 1 }
-- units of conformance -- units of conformance
vdslGroup OBJECT-GROUP vdslGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
vdslLineCoding, vdslLineCoding,
vdslLineType, vdslLineType,
vdslLineConfProfile, vdslLineConfProfile,
skipping to change at line 3398 skipping to change at page 74, line 17
vdslPerfCurr1DayLoss, vdslPerfCurr1DayLoss,
vdslPerfCurr1DayLprs, vdslPerfCurr1DayLprs,
vdslPerfCurr1DayESs, vdslPerfCurr1DayESs,
vdslPerfCurr1DaySESs, vdslPerfCurr1DaySESs,
vdslPerfCurr1DayUASs, vdslPerfCurr1DayUASs,
vdslPerfCurr1DayInits, vdslPerfCurr1DayInits,
vdslIntervalLofs, vdslIntervalLofs,
vdslIntervalLoss, vdslIntervalLoss,
vdslIntervalLprs, vdslIntervalLprs,
vdslIntervalESs, vdslIntervalESs,
Expires December 17, 2002 [PAGE 63]
vdslIntervalSESs, vdslIntervalSESs,
vdslIntervalUASs, vdslIntervalUASs,
vdslIntervalInits, vdslIntervalInits,
vdsl1DayIntervalMoniSecs, vdsl1DayIntervalMoniSecs,
vdsl1DayIntervalLofs, vdsl1DayIntervalLofs,
vdsl1DayIntervalLoss, vdsl1DayIntervalLoss,
vdsl1DayIntervalLprs, vdsl1DayIntervalLprs,
vdsl1DayIntervalESs, vdsl1DayIntervalESs,
vdsl1DayIntervalSESs, vdsl1DayIntervalSESs,
vdsl1DayIntervalUASs, vdsl1DayIntervalUASs,
skipping to change at line 3430 skipping to change at page 74, line 47
vdslChanPerfCurr1DayTimeElapsed, vdslChanPerfCurr1DayTimeElapsed,
vdslChanPerfCurr1DayCorrectedOctets, vdslChanPerfCurr1DayCorrectedOctets,
vdslChanPerfCurr1DayUncorrectBlks, vdslChanPerfCurr1DayUncorrectBlks,
vdslChanIntervalCorrectedOctets, vdslChanIntervalCorrectedOctets,
vdslChanIntervalUncorrectBlks, vdslChanIntervalUncorrectBlks,
vdslChan1DayIntervalMoniSecs, vdslChan1DayIntervalMoniSecs,
vdslChan1DayIntervalCorrectedOctets, vdslChan1DayIntervalCorrectedOctets,
vdslChan1DayIntervalUncorrectBlks, vdslChan1DayIntervalUncorrectBlks,
vdslLineConfProfileIndex, vdslLineConfProfileIndex,
vdslLineConfProfileName, vdslLineConfProfileName,
vdslLineConfTargetSnrMgn, vdslLineConfDownstreamMaxPwr,
vdslLineConfUpstreamTxSpeed, vdslLineConfUpstreamMaxPwr,
vdslLineConfDownstreamTxSpeed, vdslLineConfDownstreamMaxSnrMgn,
vdslLineConfDownstreamMinSnrMgn,
vdslLineConfDownstreamTargetSnrMgn,
vdslLineConfUpstreamMaxSnrMgn,
vdslLineConfUpstreamMinSnrMgn,
vdslLineConfUpstreamTargetSnrMgn,
vdslLineConfDownstreamFastMaxDataRate,
vdslLineConfDownstreamFastMinDataRate,
vdslLineConfDownstreamSlowMaxDataRate,
vdslLineConfDownstreamSlowMinDataRate,
vdslLineConfUpstreamFastMaxDataRate,
vdslLineConfUpstreamFastMinDataRate,
vdslLineConfUpstreamSlowMaxDataRate,
vdslLineConfUpstreamSlowMinDataRate,
vdslLineConfRateAdaptationRatio,
vdslLineConfUpstreamDataRate,
vdslLineConfDownstreamDataRate,
vdslLineConfDownstreamMaxInterDelay,
vdslLineConfUpstreamMaxInterDelay,
vdslLineConfUpstreamPboControl, vdslLineConfUpstreamPboControl,
vdslLineConfDownstreamPboControl, vdslLineConfDownstreamPboControl,
vdslLineConfDeploymentScenario, vdslLineConfDeploymentScenario,
vdslLineConfAdslOccupy, vdslLineConfAdslOccupy,
vdslLineConfApplicableStandard, vdslLineConfApplicableStandard,
vdslLineConfBandPlan, vdslLineConfBandPlan,
vdslLineConfBandPlanFx, vdslLineConfBandPlanFx,
vdslLineConfBandU0Usage, vdslLineConfBandU0Usage,
vdslLineConfUpstreamPsdTemplate, vdslLineConfUpstreamPsdTemplate,
vdslLineConfDownstreamPsdTemplate, vdslLineConfDownstreamPsdTemplate,
vdslLineConfProfileRowStatus, vdslLineConfProfileRowStatus,
vdslLineAlarmConfProfileIndex, vdslLineAlarmConfProfileIndex,
vdslLineAlarmConfProfileName, vdslLineAlarmConfProfileName,
vdslThresh15MinLofs, vdslThresh15MinLofs,
vdslThresh15MinLoss, vdslThresh15MinLoss,
vdslThresh15MinLprs, vdslThresh15MinLprs,
vdslThresh15MinESs, vdslThresh15MinESs,
vdslThresh15MinSESs, vdslThresh15MinSESs,
vdslThresh15MinUASs, vdslThresh15MinUASs,
vdslInitFailureNotificationEnable, vdslInitFailureNotificationEnable,
Expires December 17, 2002 [PAGE 64]
vdslLineAlarmConfProfileRowStatus vdslLineAlarmConfProfileRowStatus
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A collection of objects providing information about "A collection of objects providing information about
a VDSL Line." a VDSL Line."
::= { vdslGroups 1 } ::= { vdslGroups 1 }
vdslMCMGroup OBJECT-GROUP vdslMCMGroup OBJECT-GROUP
OBJECTS OBJECTS
skipping to change at line 3501 skipping to change at page 76, line 30
"A collection of objects providing configuration "A collection of objects providing configuration
information for a VDSL line based upon multiple carrier information for a VDSL line based upon multiple carrier
modulation modem." modulation modem."
::= { vdslGroups 2 } ::= { vdslGroups 2 }
vdslSCMGroup OBJECT-GROUP vdslSCMGroup OBJECT-GROUP
OBJECTS OBJECTS
{ {
vdslSCMPhysBandSnrMgn, vdslSCMPhysBandSnrMgn,
vdslSCMPhysBandAtn, vdslSCMPhysBandAtn,
vdslSCMConfProfileInterleaveDepth, vdslSCMConfProfileDownInterleaveDepth,
vdslSCMConfProfileFastCodewordSize, vdslSCMConfProfileUpInterleaveDepth,
vdslSCMConfProfileDownNumCarriers,
vdslSCMConfProfileUpNumCarriers,
vdslSCMConfProfileDownFastCodewordSize,
vdslSCMConfProfileUpFastCodewordSize,
vdslSCMConfProfileTransmitPSDMask, vdslSCMConfProfileTransmitPSDMask,
vdslSCMConfProfileBands, vdslSCMConfProfileVendorNotch1Start,
vdslSCMConfProfileFastFecSize, vdslSCMConfProfileVendorNotch1Stop,
vdslSCMConfProfileVendorNotch2Start,
vdslSCMConfProfileVendorNotch2Stop,
vdslSCMConfProfileDownFastFecSize,
vdslSCMConfProfileUpFastFecSize,
vdslSCMConfProfileDownSlowBlockSize,
vdslSCMConfProfileUpSlowBlockSize,
vdslSCMConfProfileRowStatus, vdslSCMConfProfileRowStatus,
vdslSCMConfProfileTxBandSide,
vdslSCMConfProfileTxBandNumber, vdslSCMConfProfileTxBandNumber,
Expires December 17, 2002 [PAGE 65]
vdslSCMConfProfileTxBandTransmitPSDLevel, vdslSCMConfProfileTxBandTransmitPSDLevel,
vdslSCMConfProfileTxBandSymbolRateProfile, vdslSCMConfProfileTxBandSymbolRateProfile,
vdslSCMConfProfileTxBandConstellationSize, vdslSCMConfProfileTxBandConstellationSize,
vdslSCMConfProfileTxBandCenterFrequency, vdslSCMConfProfileTxBandCenterFrequency,
vdslSCMConfProfileTxBandRowStatus vdslSCMConfProfileTxBandRowStatus
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A collection of objects providing configuration "A collection of objects providing configuration
information for a VDSL line based upon single carrier information for a VDSL line based upon single carrier
skipping to change at line 3532 skipping to change at page 77, line 18
vdslNotificationGroup NOTIFICATION-GROUP vdslNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS NOTIFICATIONS
{ {
vdslPerfLofsThreshNotification, vdslPerfLofsThreshNotification,
vdslPerfLossThreshNotification, vdslPerfLossThreshNotification,
vdslPerfLprsThreshNotification, vdslPerfLprsThreshNotification,
vdslPerfESsThreshNotification, vdslPerfESsThreshNotification,
vdslPerfSESsThreshNotification, vdslPerfSESsThreshNotification,
vdslPerfUASsThreshNotification, vdslPerfUASsThreshNotification,
vdslDownMaxSnrMgnExceededNotification,
vdslDownMinSnrMgnExceededNotification,
vdslUpMaxSnrMgnExceededNotification,
vdslUpMinSnrMgnExceededNotification,
vdslInitFailureNotification vdslInitFailureNotification
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This group supports notifications of significant "This group supports notifications of significant
conditions associated with VDSL Lines." conditions associated with VDSL Lines."
::= { vdslGroups 4 } ::= { vdslGroups 4 }
END END
skipping to change at line 3557 skipping to change at page 77, line 47
Part 1: Functional requirements", October 1999. Part 1: Functional requirements", October 1999.
[ETSI2702] ETSI TS 101 270-2 V1.1.1 "Transmission and Multiplexing [ETSI2702] ETSI TS 101 270-2 V1.1.1 "Transmission and Multiplexing
(TM); Access transmission systems on metallic access (TM); Access transmission systems on metallic access
cables; Very high speed Digital Subscriber Line (VDSL); cables; Very high speed Digital Subscriber Line (VDSL);
Part 1: Transceiver specification", February 2001. Part 1: Transceiver specification", February 2001.
[ITU9931] ITU-T G.993.1 "Very-high-speed digital subscriber line [ITU9931] ITU-T G.993.1 "Very-high-speed digital subscriber line
foundation", November 2001. foundation", November 2001.
[ITU9971] ITU-T G.997.1 "Physical layer management for Digital
Subscriber Line (DSL) Transcievers", July 1999.
[RFC1901] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, [RFC1901] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Introduction to Community-based SNMPv2", RFC 1901, "Introduction to Community-based SNMPv2", RFC 1901,
January 1996. January 1996.
[RFC1905] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, [RFC1905] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Protocol Operations for Version 2 of the Simple Network "Protocol Operations for Version 2 of the Simple Network
Expires December 17, 2002 [PAGE 66]
Management Protocol (SNMPv2)", RFC 1905, January 1996. Management Protocol (SNMPv2)", RFC 1905, January 1996.
[RFC1906] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, [RFC1906] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Transport Mappings for Version 2 of the Simple Network "Transport Mappings for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1906, January 1996. Management Protocol (SNMPv2)", RFC 1906, January 1996.
[RFC2119] Bradner, S., "Key Words for use in RFCs to Indicate [RFC2119] Bradner, S., "Key Words for use in RFCs to Indicate
Requirement Levels", RFC 2119, March 1997. Requirement Levels", RFC 2119, March 1997.
[RFC2493] Tesink, K., "Textual Conventions for MIB Modules Using [RFC2493] Tesink, K., "Textual Conventions for MIB Modules Using
skipping to change at line 3618 skipping to change at page 79, line 5
[T1E1311] ANSI T1E1.4/2001-311, "Very-high-bit-rate Digital [T1E1311] ANSI T1E1.4/2001-311, "Very-high-bit-rate Digital
Subscriber Line (VDSL) Metallic Interface, Part 1: Subscriber Line (VDSL) Metallic Interface, Part 1:
Functional Requirements and Common Specification", February Functional Requirements and Common Specification", February
2001. 2001.
[T1E1011] ANSI T1E1.4/2001-011R3, "VDSL Metallic Interface, Part 2: [T1E1011] ANSI T1E1.4/2001-011R3, "VDSL Metallic Interface, Part 2:
Technical Specification for a Single-Carrier Modulation Technical Specification for a Single-Carrier Modulation
(SCM) Transceiver", November 2001. (SCM) Transceiver", November 2001.
Expires December 17, 2002 [PAGE 67]
[T1E1013] ANSI T1E1.4/2001-013R4, "VDSL Metallic Interface, Part 3: [T1E1013] ANSI T1E1.4/2001-013R4, "VDSL Metallic Interface, Part 3:
Technical Specification for a Multi-Carrier Modulation Technical Specification for a Multi-Carrier Modulation
(MCM) Transceiver", November 2000. (MCM) Transceiver", November 2000.
Informative References Informative References
[RFC1155] Rose, M. and K. McCloghrie, "Structure and Identification [RFC1155] Rose, M. and K. McCloghrie, "Structure and Identification
of Management Information for TCP/IP-based Internets", STD of Management Information for TCP/IP-based Internets", STD
16, RFC 1155, May 1990. 16, RFC 1155, May 1990.
skipping to change at line 3672 skipping to change at page 80, line 6
sufficient notifications to potentially overwhelm either the sufficient notifications to potentially overwhelm either the
management interface to the network or the element manager. management interface to the network or the element manager.
For this reason, there are a number of managed objects in this MIB For this reason, there are a number of managed objects in this MIB
that may contain sensitive information. These are: that may contain sensitive information. These are:
vdslThresh15MinLofs vdslThresh15MinLofs
vdslThresh15MinLoss vdslThresh15MinLoss
vdslThresh15MinLprs vdslThresh15MinLprs
vdslThresh15MinESs vdslThresh15MinESs
Expires December 17, 2002 [PAGE 68]
vdslThresh15MinSESs vdslThresh15MinSESs
vdslThresh15MinUASs vdslThresh15MinUASs
It is thus important to control even GET access to these objects and It is thus important to control even GET access to these objects and
possibly to even encrypt the values of these objects when sending possibly to even encrypt the values of these objects when sending
them over the network via SNMP. Not all versions of SNMP provide them over the network via SNMP. Not all versions of SNMP provide
features for such a secure environment. features for such a secure environment.
Further, notifications generated by agents implementing this MIB Further, notifications generated by agents implementing this MIB
will contain the above threshold information. will contain the above threshold information.
skipping to change at line 3727 skipping to change at page 81, line 7
pertain to the implementation or use of the technology described in pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11. Copies of standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances of claims of rights made available for publication and any assurances of
licenses to be made available, or the result of an attempt made to licenses to be made available, or the result of an attempt made to
obtain a general license or permission for the use of such obtain a general license or permission for the use of such
proprietary rights by implementors or users of this specification can proprietary rights by implementors or users of this specification can
Expires December 17, 2002 [PAGE 69]
be obtained from the IETF Secretariat. be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary copyrights, patents or patent applications, or other proprietary
rights which may cover technology that may be required to practice rights which may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive this standard. Please address the information to the IETF Executive
Director. Director.
Authors' Addresses Authors' Addresses
skipping to change at line 3782 skipping to change at line 4196
English. English.
The limited permissions granted above are perpetual and will not be The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns. revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Expires December 17, 2002 [PAGE 70]
 End of changes. 

This html diff was produced by rfcdiff 1.23, available from http://www.levkowetz.com/ietf/tools/rfcdiff/