Network Working Group                                            B. Ray
Category: Internet Draft                         PESA Switching Systems
                                                                R. Abbi
                                                                Alcatel
                                                               May
                                                              June 2003

                Definitions of Managed Objects for Very High
                    Speed Digital Subscriber Lines (VDSL)
                       draft-ietf-adslmib-vdsl-09.txt
                       draft-ietf-adslmib-vdsl-10.txt

Status of this Memo

   This document is an Internet-Draft and is subject to in full conformance with
   all provisions of Section 10 of RFC2026.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.
   Internet-Drafts.

   Internet-Drafts are draft documents valid for a maximum of six
   months and may be updated, replaced, or obsoleted by other documents
   at any time.  It is inappropriate to use Internet-Drafts as
   reference material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
              http://www.ietf.org/1id-abstracts.txt at:
     http://www.ietf.org/ietf/1id-abstracts.txt

   The list of Internet-Draft Shadow Directories can be accessed at
              http://www.ietf.org/shadow.html at:
   http://www.ietf.org/shadow.html.

Copyright Notice

   Copyright (C) The Internet Society (2003).  All Rights Reserved.

Abstract

   This document defines a portion of the Management Information Base
   (MIB) module for use with network management protocols in the
   Internet community.  In particular, it describes objects used for
   managing Very high speed High Speed Digital Subscriber Line (VDSL) interfaces [T1E1311, T1E1011, T1E1013,
   ETSI2701, ETSI2702, ITU9931, ITU9971].

   This document specifies a MIB module in a manner that is compliant
   to the SMIv2 (STD 58 [RFC2578, RFC2579, RFC2580]). interfaces.

Table of Contents

1.  The SNMP Internet-Standard Management Framework ............................. ....................   2
2.  Overview ..................................................    3 ......................................................   2
2.1 Relationship of the VDSL Line MIB Module to other MIBs ...........    3 MIB Modules .   2
2.2 Conventions used in the MIB ...............................    5 Module ............................   4
2.3 Structure ................................................. .....................................................   5
2.4 Counters, Interval Buckets and Thresholds .................    7 .....................   6
2.5 Profiles .................................................. ......................................................   7
2.6 Notifications ............................................. .................................................   8
2.7 Persistence ............................................... ...................................................   9
3.  Conformance and Compliance ................................ ....................................  10
4.  Definitions ............................................... ...................................................  10
5.  Intellectual Property .........................................  64
6.  Normative References ..........................................  65
7.  Informative References ................................................   58 ........................................  66
8.  Security Considerations ...................................   62
        IANA Considerations .......................................   62
        Acknowledgments ...........................................   62
        Intellectual Property Notice ..............................   63  66
9.  Acknowledgements ..............................................  67
10. Authors' Addresses ........................................   63 ............................................  68
11. Full Copyright Statement ..................................   64 ......................................  68

1.  The SNMP Management Framework

   The SNMP Internet-Standard Management Framework presently consists of five major
   components:

   o   An overall architecture, described in RFC 2571 [RFC2571].

   o   Mechanisms for describing and naming objects and events for the
       purpose of management.  The first version of this Structure of
       Management Information (SMI) is called SMIv1 and described in
       STD 16 [RFC1155, RFC1212] and RFC 1215 [RFC1215].  The second
       version, called SMIv2, is described in STD 58 [RFC2578, RFC2579,
       RFC2580].

   o   Message protocols for transferring management information.  The
       first version of the SNMP message protocol is called SNMPv1 and
       described in STD 15 [RFC1157].  A second version of the SNMP
       message protocol, which is not an Internet standards track
       protocol, is called SNMPv2c and described in RFC 1901 [RFC1901]
       and RFC 1906 [RFC1906].  The third version of the message
       protocol is called SNMPv3 and described in RFC 1906 [RFC1906],
       RFC 2572 [RFC2572] and RFC 2574 [RFC2574].

   o   Protocol operations for accessing management information.  The
       first set of protocol operations and associated PDU formats is
       described in STD 15 [RFC1157].  A second set of protocol
       operations and associated PDU formats is described in RFC 1905
       [RFC1905].

   o   A set

   For a detailed overview of fundamental applications described in RFC 2573 [RFC2573]
       and the view-based access control mechanism described in RFC
       2575 [RFC2575].

   A more detailed introduction to documents that describe the current SNMP
   Internet-Standard Management Framework
   can be found in Framework, please refer to section 7 of
   RFC 2570 [RFC2570]. 3410 [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  MIB objects are generally
   accessed through the Simple Network Management Protocol (SNMP).
   Objects in the MIB are defined using the mechanisms defined in the SMI.
   Structure of Management Information (SMI).  This memo specifies a
   MIB module that is compliant to the SMIv2. The
   textual conventions used SMIv2, which is described in this MIB module cannot be translated
   to SMIv1 since the Counter64 type does not exist in SMIv1.

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED",  "MAY", STD
   58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and "OPTIONAL" in
   this document are to be interpreted as described in STD 58, RFC 2119
   [RFC2119].
   2580 [RFC2580].

2.  Overview

   This document describes an SNMP MIB module for managing VDSL Lines.
   These definitions are based upon the specifications for VDSL as
   defined in T1E1, ETSI, and ITU documentation [T1E1311, T1E1011,
   T1E1013, ETSI2701, ETSI2702, ITU9931, ITU9971].

   The MIB module is located in the MIB tree under MIB 2 transmission,
   as discussed in the MIB-2 Integration (RFC 2863 [RFC2863]) section
   of this document.

2.1  Relationship of the VDSL Line MIB Module to other MIBs MIB Modules

   This section outlines the relationship of this MIB with other MIBs
   described in RFCs.  Specifically, IF-MIB as presented in RFC 2863
   [RFC2863] is discussed.

2.1.1  General IF-MIB Integration (RFC 2863)

   The VDSL Line MIB specifies the detailed attributes of a data
   interface.  As such, it needs to integrate with RFC 2863 [RFC2863].
   The IANA has assigned the following ifType to VDSL:

   IANAifType ::= TEXTUAL-CONVENTION
       ...

   SYNTAX INTEGER {
       ...
       vdsl(97), -- Very H-speed Digital Subscrib.  Loop
       ...
       }

   Additionally, a VDSL line may contain an optional fast channel
   and an optional interleaved channel which also integrate into RFC
   2863 [RFC2863].  The IANA has assigned the following ifTypes to
   these channels:

   IANAifType ::= TEXTUAL-CONVENTION
       ...
   SYNTAX INTEGER {
       ...
       interleave (124), -- Interleave channel
       fast (125),       -- Fast channel
       ...
       }

2.1.2  Usage of ifTable

   The MIB branch identified by this ifType contains tables appropriate
   for this interface type.  Most such tables extend the ifEntry table,
   and are indexed by ifIndex.  For interfaces in systems implementing
   this MIB, those table entries indexed by ifIndex MUST be persistent.

   The following attributes are part of the mandatory ifGeneral group
   in RFC 2863 [RFC2863], and are not duplicated in the VDSL Line MIB.

   ===================================================================
       ifIndex                  Interface index.

       ifDescr                  See interfaces MIB [RFC2863].

       ifType                   vdsl(97),
                                interleaved(124), or
                                fast(125)

       ifSpeed                  Set as appropriate.

       ifPhysAddress            This object MUST have an octet string
                                with zero length.

       ifAdminStatus            See interfaces MIB [RFC2863].

       ifOperStatus             See interfaces MIB [RFC2863].

       ifLastChange             See interfaces MIB [RFC2863].

       ifName                   See interfaces MIB [RFC2863].

       ifHighSpeed              Set as appropriate.

       ifConnectorPresent       Set as appropriate.

       ifLinkUpDownTrapEnable   Default to enabled(1).

   ===================================================================
                   Figure 1: Use of ifTable Objects

   Section 2.3, below, describes the structure of this MIB in relation
   to ifEntry in greater detail.

2.2 Conventions used in the MIB Module

2.2.1 Naming Conventions

   A.  Vtuc -- (VTUC) modem transceiver at near (Central) end of line
   B.  Vtur -- (VTUR) modem transceiver at Remote end of line
   C.  Vtu  -- One of either Vtuc or Vtur
   D.  Curr -- Current
   E.  Prev -- Previous
   F.  Atn  -- Attenuation
   G.  ES   -- Errored Second
   H.  SES  -- Severely Errored Second
   I.  UAS  -- Unavailable Second
   J.  LCS  -- Line Code Specific
   K.  Lof  -- Loss of Frame
   L.  Lol  -- Loss of Link
   M.  Los  -- Loss of Signal
   N.  Lpr  -- Loss of Power
   O.  xxxs -- interval Sum of Seconds in which xxx has occurs (e.g., xxx=Lof,
               Los, Lpr, Lol)
   P.  Max  -- Maximum
   Q.  Mgn  -- Margin
   R.  Min  -- Minimum
   S.  Psd  -- Power Spectral Density
   T.  Snr  -- Signal to Noise Ratio
   U.  Tx   -- Transmit
   V.  Blks -- Blocks

2.2.2 Textual Conventions

   The following textual conventions are defined to reflect the line
   topology in the MIB (further discussed in the following section)
   and to define the behavior of the statistics to be maintained
   by an agent.

   o    VdslLineCodingType :

   Attributes with this syntax identify the line coding used.
   Specified as an INTEGER, the three values are:

   other(1)  -- none of the following
   mcm(2)    -- Multiple Carrier Modulation
   scm(3)    -- Single Carrier Modulation

   o    VdslLineEntity :

   Attributes with this syntax reference the two sides of a line.
   Specified as an INTEGER, the two values are:

   vtuc(1)  -- central site modem transceiver
   vtur(2)  -- remote site modem transceiver

2.3  Structure

   The MIB is structured into the following MIB groups:

   o   vdslGroup :

   This group supports all line code independent MIB objects found
   in this MIB.  The following tables contain objects permitted for
   ifType vdsl(97):

      - vdslLineTable
      - vdslPhysTable
      - vdslPerfDataTable
      - vdslPerfIntervalTable
      - vdslPerf1DayIntervalTable
      - vdslLineConfProfileTable
      - vdslLineAlarmConfProfileTable

   The following tables contain objects permitted for ifTypes
   interleaved(124) and (fast):

      - vdslChanTable
      - vdslChanPerfDataTable
      - vdslChanPerfIntervalTable
      - vdslChanPerf1DayIntervalTable

   Figure 2, below, displays the relationship of the tables in the
   vdslGroup to ifEntry (and each other):

     ifEntry(ifType=97)  ----> vdslLineTableEntry 1:(0..1) 1:(0 to 1)

     vdslLineTableEntry  ----> vdslPhysTableEntry 1:(0..2) 1:(0 to 2)
                         ----> vdslPerfDataEntry 1:(0..2) 1:(0 to 2)
                         ----> vdslLineConfProfileEntry 1:(0..1) 1:(0 to 1)
                         ----> vdslLineAlarmConfProfileEntry 1:(0..1) 1:(0 to 1)

     vdslPhysTableEntry  ----> vdslPerfIntervalEntry 1:(0..96) 1:(0 to 96)
                         ----> vdslPerf1DayIntervalEntry 1:(0..30) 1:(0 to 30)

     ifEntry(ifType=124) ----> vdslChanEntry 1:(0..2) 1:(0 to 2)
                         ----> vdslChanPerfDataEntry 1:(0..2) 1:(0 to 2)

     ifEntry(ifType=125) ----> vdslChanEntry 1:(0..2) 1:(0 to 2)
                         ----> vdslChanPerfDataEntry 1:(0..2) 1:(0 to 2)

     vdslChanEntry       ----> vdslchanPerfIntervalEntry 1:(0..96) 1:(0 to 96)
                         ----> vdslchan1DayPerfIntervalEntry 1:(0..30) 1:(0 to 30)

                   Figure 2: Table Relationships

   o   vdslNotificationGroup :

   This group contains definitions of VDSL line notifications.  Section
   2.6, below, presents greater detail on the notifications defined
   within the MIB module.

2.3.1  Line Topology

   A VDSL Line consists of a two units - a Vtuc (the central termination tranceiver
   unit) and a Vtur (the remote termination transceiver unit).

             <-- Network Side   Customer Side -->

             |<////////// VDSL Line ///////////>|

             +-------+                  +-------+
             |       |                  |       |
             | Vtuc  +------------------+  Vtur |
             |       |                  |       |
             +-------+                  +-------+

          Figure 3: General topology for a VDSL Line

2.4  Counters, Interval Buckets and Thresholds

   For Loss of Frame (lof), Loss of Link (lol), Loss of Signal (los),
   and Loss of Power (lpr), Errored Seconds (ES), Severely Errored
   Seconds (SES), and Unavailable Seconds (UAS) there are event
   counters, current 15-minute, 0 to 96 15-minute history bucket(s),
   and 0 to 30 1-day history bucket(s) of "interval-counters".  Each
   current 15-minute event bucket has an associated threshold
   notification.

   Each of these counters uses the textual conventions defined in the
   HC-PerfHist-TC-MIB.
   HC-PerfHist-TC-MIB [RFCXXXX].  The HC-PerfHist-TC-MIB is a work-in-progress,
   but simply defines 64-bit 64-
--- RFC Ed: please replace XXXX with the RFC number assigned to the
--- accompanying HC-TC MIB
   bit versions of the textual conventions found in RFC 2493 [RFC2493].

   There is no requirement for an agent to ensure a fixed relationship
   between the start of a fifteen minute interval and any wall clock; however
   however, some implementations may align the fifteen minute intervals
   with quarter hours.  Likewise, an implementation may choose to align
   one day intervals with the start of a day.

   Counters are not reset when an a Vtu is reinitialized, only when the
   agent is reset or reinitialized (or under specific request outside
   the scope of this MIB). MIB module).

2.5  Profiles

   As a managed node can handle a large number of Vtus, (e.g., hundreds
   or perhaps thousands of lines), provisioning every parameter on
   every Vtu may become burdensome.  Moreover, most lines are
   provisioned identically with the same set of parameters.  To
   simplify the provisioning process, this MIB makes use of profiles.
   A profile is a set of parameters that can be shared by multiple
   lines using the same configuration.

   The following profiles are used in this MIB: MIB module:

   o   Line Configuration Profiles - Line configuration profiles
       contain parameters for configuring VDSL lines.  They are defined
       in the vdslLineConfProfileTable.

   o   Alarm Configuration Profiles - These profiles contain parameters
       for configuring alarm thresholds for VDSL modems. transceivers.  These
       profiles are defined in the vdslLineAlarmConfProfileTable.

   One or more lines may be configured to share parameters of a single
   profile by setting its vdslLineConfProfile objects to the value of
   this profile.  If a change is made to the profile, all lines that
   refer to it will be reconfigured to the changed parameters.  Before
   a profile can be deleted or taken out of service it must be first
   unreferenced from all associated lines.

   Implementations MUST provide a default profile with an index value
   of
   `DEFVAL' 'DEFVAL' for each profile type.  The values of the associated
   parameters will be vendor specific unless otherwise indicated in
   this document.  Before a line's profiles have been set, these
   profiles will be automatically used by setting vdslLineConfProfile
   and vdslLineAlarmConfProfile to `DEFVAL' 'DEFVAL' where appropriate.  This
   default profile name, 'DEFVAL', is considered reserved in the
   context of profiles defined in this MIB. MIB module.

   Profiles are created, assigned, and deleted dynamically using the
   profile name and profile row status in each of the ten profile
   tables (nine line configuration tables and one alarm configuration
   table).

   Profile changes MUST take effect immediately.  These changes MAY
   result in a restart (hard reset or soft restart) of the units on the
   line.

2.6  Notifications

   The ability to generate the SNMP notifications coldStart/WarmStart
   (per [RFC2863]) [RFC3418]) which are per agent (e.g., per Digital Subscriber
   Line Access Multiplexer, or DSLAM, in such a device), and
   linkUp/linkDown (per [RFC2863]) which are per interface (i.e., VDSL
   line) is required.

   The notifications defined in this MIB are for initialization failure
   and for the threshold crossings associated with the following
   events: lof, lol, los, lpr, ES, SES, and UAS.  Each threshold has
   its own enable/threshold value.  When that value is 0, the
   notification is disabled.

   A linkDown notification MAY be generated whenever any of lof, lol,
   los, lpr, ES, SES, or UAS threshold crossing event (as defined
   in this MIB) MIB module) occurs.  The corresponding linkUp notification
   MAY be sent when all link failure conditions are cleared.

   The vdslCurrStatus is a bitmask representing all outstanding error
   conditions associated with a particular VDSL modem. transceiver.  Note that
   since status of remote modems transceivers is obtained via the EOC, this
   information may be unavailable for units that are unreachable via
   EOC during a line error condition.  Therefore, not all conditions
   may always be included in its current status.  Notifications
   corresponding to the bit fields in this object are defined.

   A threshold notification occurs whenever the corresponding current
   15-minute interval error counter becomes equal to, or exceeds the
   threshold value.  One notification may be sent per interval per
   interface.  Since the current 15-minute counter are reset to 0 every
   15 minutes, if the condition persists, the notification may recur as
   often as every 15 minutes.  For example, to get a notification
   whenever a "loss of" event occurs (but at most once every 15
   minutes), set the corresponding threshold to 1.  The agent will
   generate a notification when the event originally occurs.

   Note that the Network Management System, or NMS, may receive a
   linkDown notification, as well, if enabled (via
   ifLinkUpDownTrapEnable [RFC2863]).  At the beginning of the next 15
   minute interval, the counter is reset.  When the first second goes
   by and the event occurs, the current interval bucket will be 1,
   which equals the threshold and the notification will be sent again.

2.7  Persistence

   All read-write and read-create objects defined in this MIB which may be set (read-write or
   read-create), should module
   SHOULD be stored persistently.  Following is an exhaustive list of
   these persistent objects:

        vdslLineConfProfile
        vdslLineAlarmConfProfile
        vdslLineConfProfileName
        vdslLineConfDownstreamRateMode
        vdslLineConfUpstreamRateMode
        vdslLineConfDownstreamMaxPwr
        vdslLineConfUpstreamMaxPwr
        vdslLineConfDownstreamMaxSnrMgn
        vdslLineConfDownstreamMinSnrMgn
        vdslLineConfDownstreamTargetSnrMgn
        vdslLineConfUpstreamMaxSnrMgn
        vdslLineConfUpstreamMinSnrMgn
        vdslLineConfUpstreamTargetSnrMgn
        vdslLineConfDownstreamFastMaxDataRate
        vdslLineConfDownstreamFastMinDataRate
        vdslLineConfDownstreamSlowMaxDataRate
        vdslLineConfDownstreamSlowMinDataRate
        vdslLineConfUpstreamFastMaxDataRate
        vdslLineConfUpstreamFastMinDataRate
        vdslLineConfUpstreamSlowMaxDataRate
        vdslLineConfUpstreamSlowMinDataRate
        vdslLineConfDownstreamRateRatio
        vdslLineConfUpstreamRateRatio
        vdslLineConfDownstreamMaxInterDelay
        vdslLineConfUpstreamMaxInterDelay
        vdslLineConfDownstreamPboControl
        vdslLineConfUpstreamPboControl
        vdslLineConfDownstreamPboLevel
        vdslLineConfUpstreamPboLevel
        vdslLineConfDownRateMode
        vdslLineConfUpRateMode
        vdslLineConfDownMaxPwr
        vdslLineConfUpMaxPwr
        vdslLineConfDownMaxSnrMgn
        vdslLineConfDownMinSnrMgn
        vdslLineConfDownTargetSnrMgn
        vdslLineConfUpMaxSnrMgn
        vdslLineConfUpMinSnrMgn
        vdslLineConfUpTargetSnrMgn
        vdslLineConfDownFastMaxDataRate
        vdslLineConfDownFastMinDataRate
        vdslLineConfDownSlowMaxDataRate
        vdslLineConfDownSlowMinDataRate
        vdslLineConfUpFastMaxDataRate
        vdslLineConfUpFastMinDataRate
        vdslLineConfUpSlowMaxDataRate
        vdslLineConfUpSlowMinDataRate
        vdslLineConfDownRateRatio
        vdslLineConfUpRateRatio
        vdslLineConfDownMaxInterDelay
        vdslLineConfUpMaxInterDelay
        vdslLineConfDownPboControl
        vdslLineConfUpPboControl
        vdslLineConfDownPboLevel
        vdslLineConfUpPboLevel
        vdslLineConfDeploymentScenario
        vdslLineConfAdslPresence
        vdslLineConfApplicableStandard
        vdslLineConfBandPlan
        vdslLineConfBandPlanFx
        vdslLineConfBandU0Usage
        vdslLineConfUpstreamPsdTemplate
        vdslLineConfDownstreamPsdTemplate
        vdslLineConfBandOptUsage
        vdslLineConfUpPsdTemplate
        vdslLineConfDownPsdTemplate
        vdslLineConfHamBandMask
        vdslLineConfCustomNotch1Start
        vdslLineConfCustomNotch1Stop
        vdslLineConfCustomNotch2Start
        vdslLineConfCustomNotch2Stop
        vdslLineConfDownstreamTargetSlowBurstProtection
        vdslLineConfUpstreamTargetSlowBurstProtection
        vdslLineConfDownstreamMaxFastFecOverhead
        vdslLineConfUpstreamMaxFastFecOverhead
        vdslLineConfProfileRowStatus
        vdslLineConfDownTargetSlowBurst
        vdslLineConfUpTargetSlowBurst
        vdslLineConfDownMaxFastFec
        vdslLineConfUpMaxFastFec
        vdslLineConfLineType
        vdslLineConfProfRowStatus
        vdslLineAlarmConfProfileName
        vdslThresh15MinLofs
        vdslThresh15MinLoss
        vdslThresh15MinLprs
        vdslThresh15MinLols
        vdslThresh15MinESs
        vdslThresh15MinSESs
        vdslThresh15MinUASs
        vdslInitFailureNotificationEnable
        vdslLineAlarmConfProfileRowStatus
        vdslInitFailureNotifyEnable
        vdslLineAlarmConfProfRowStatus

   It should SHOULD also be noted that interface indices in this MIB are
   maintained persistently.  VACM data relating to these should SHOULD be
   stored persistently as well. well [RFC2575].

3.  Conformance and Compliance

   For VDSL lines, the following group is groups are mandatory:

      -  vdslGroup
      -  vdslNotificationGroup

4. Definitions

    VDSL-LINE-MIB DEFINITIONS ::= BEGIN

    IMPORTS

    MODULE-IDENTITY,
    OBJECT-TYPE,
    Counter64,
    Gauge32,
    Integer32,
    Unsigned32,
    NOTIFICATION-TYPE,
    transmission                    FROM SNMPv2-SMI
    ZeroBasedCounter64              FROM HCNUM-TC
    TEXTUAL-CONVENTION,
    RowStatus,
    TruthValue                      FROM SNMPv2-TC
    HCPerfValidIntervals,
    HCPerfInvalidIntervals,
    HCPerfTimeElapsed,
    HCPerfIntervalThreshold,
    HCPerfCurrentCount,
    HCPerfIntervalCount             FROM HC-PerfHist-TC-MIB
    MODULE-COMPLIANCE,
    OBJECT-GROUP,
    NOTIFICATION-GROUP              FROM SNMPv2-CONF
    ifIndex                         FROM IF-MIB
    SnmpAdminString                 FROM SNMP-FRAMEWORK-MIB;

    vdslMIB MODULE-IDENTITY
       LAST-UPDATED "200305010000Z" "200306060000Z" -- May 1, June 6, 2003
       ORGANIZATION "ADSLMIB Working Group"
       CONTACT-INFO "WG-email:  adslmib@ietf.org
              Info:      https://www1.ietf.org/mailman/listinfo/adslmib

              Chair:     Mike Sneed
                         Sand Channel Systems
              Postal:    P.O.  Box 37324
                         Raleigh NC 27627-7324
                         USA
              Email:     sneedmike@hotmail.com
              Phone:     +1 206 600 7022

              Co-editor: Bob Ray
                         PESA Switching Systems, Inc.
              Postal:    330-A Wynn Drive
                         Huntsville, AL 35805
                         USA
              Email:     rray@pesa.com
              Phone:     +1 256 726 9200 ext.  142

              Co-editor: Rajesh Abbi
                         Alcatel USA
              Postal:    2912 Wake Forest Road
                         Raleigh, NC 27609-7860
                         USA
              Email:     Rajesh.Abbi@alcatel.com
              Phone:     +1 919 850 6194
            "
    DESCRIPTION
        "The MIB module defining objects for the management of a pair
        of VDSL modems transceivers at each end of the VDSL line.  Each such
        line has an entry in an ifTable which may include multiple modem
        transceiver lines.  An agent may reside at either end of the
        VDSL line however line.  However, the MIB is designed to require no
        management communication between them beyond that inherent in
        the low-level VDSL line protocol.  The agent may monitor and
        control this protocol for its needs.

        VDSL lines may support optional Fast or Interleaved channels.
        If these are supported, additional entries corresponding to the
        supported channels must be created in the ifTable.  Thus a VDSL
        line that supports both channels will have three entries in the
        ifTable, one for each physical, fast, and interleaved, whose
        ifType values are equal to vdsl(97), fast(125), and
        interleaved(124), respectively.  The ifStackTable is used to
        represent the relationship between the entries.

        Naming Conventions:
            Vtuc -- (VTUC) modem transceiver at near (Central) end of line
            Vtur -- (VTUR) modem transceiver at Remote end of line
            Vtu  -- One of either Vtuc or Vtur
            Curr -- Current
            Prev -- Previous
            Atn  -- Attenuation
            ES   -- Errored Second.
            SES  -- Severely Errored Second
            UAS  -- Unavailable Second
            LCS  -- Line Code Specific
            Lof  -- Loss of Frame
            Lol  -- Loss of Link
            Los  -- Loss of Signal
            Lpr  -- Loss of Power
            xxxs -- interval Interval of Seconds in which xxx occurs
                    (e.g., xxx=Lof, Los, Lpr)
            Max  -- Maximum
            Mgn  -- Margin
            Min  -- Minimum
            Psd  -- Power Spectral Density
            Snr  -- Signal to Noise Ratio
            Tx   -- Transmit
            Blks -- Blocks
            "
    REVISION "200111010000Z" -- November 1, 2001
    DESCRIPTION "Initial draft."

    REVISION "200203310000Z" -- March 31, 2002
    DESCRIPTION "Added R. Abbi as co-author."

    REVISION "200204090000Z" -- April 9, 2002
    DESCRIPTION "Removed use

        Copyright (C) The Internet Society (2003).  This version
        of IMPLIED profile indices."

    REVISION "200206160000Z" -- June 16, 2002
    DESCRIPTION "Revised per input from DSL Forum."

    REVISION "200209230000Z" -- September 23, 2002
    DESCRIPTION "Revised per more input from DSL Forum."

    REVISION "200210150000Z" -- October 15, 2002
    DESCRIPTION "Modified per input from Randy Presuhn and
                 Moti Morgenstern."

    REVISION "200210300000Z" -- October 30, 2002
    DESCRIPTION "Modified per input from Umberto Bonollo
                 and Travis Levin."

    REVISION "200212300000Z" -- December 30, 2002
    DESCRIPTION "Changed profile indices to strings."
    REVISION "200304180000Z" this MIB module is part of RFC XXXX: see the RFC
        itself for full legal notices."
-- April 18, 2003
    DESCRIPTION "Brought into conformance RFC Ed.: replace XXXX with DSLF TR-057." assigned number & remove this note
        REVISION "200305010000Z" "200306060000Z" -- May 1, June 6, 2003
        DESCRIPTION "Added vdslLineConfDownstreamTargetSlowBurstProtection,
                vdslLineConfUpstreamTargetSlowBurstProtection,
                vdslLineConfDownstreamMaxFastFecOverhead,
                vdslLineConfUpstreamMaxFastFecOverhead,
                vdslChanCurrTxSlowBurstProtection,
                vdslChanCurrTxFastFecOverhead.

                Changed 1024 to 1000 (1kbps = 1000 bps) for objects
                related to transmission speeds." "Initial version, published as RFC XXXX."
-- RFC Ed.: replace XXXX with assigned number & remove this note
    ::= { transmission xxxx YYYY }
-- RFC Ed.: replace YYYY with IANA-assigned number & remove this note

    vdslLineMib    OBJECT IDENTIFIER ::= { vdslMIB 1 }
    vdslMibObjects OBJECT IDENTIFIER ::= { vdslLineMib 1 }

    --
    -- textual conventions used in this MIB
    --

    VdslLineCodingType ::= TEXTUAL-CONVENTION
        STATUS       current
        DESCRIPTION
            "This data type is used as the syntax for the VDSL Line Code."
        SYNTAX  INTEGER
            {
            other(1),
            Code.  Attributes with this syntax identify the line coding
            used.  Specified as an INTEGER, the three values are:

            other(1)  -- none of the following
            mcm(2),
            mcm(2)    -- Multiple Carrier Modulation
            scm(3)    -- Single Carrier Modulation Modulation"
        SYNTAX  INTEGER
            {
            other(1),
            mcm(2),
            scm(3)
            }

    VdslLineEntity ::= TEXTUAL-CONVENTION
        STATUS       current
        DESCRIPTION
            "Identifies a modem transceiver as being either Vtuc or Vtur.
            A VDSL line consists of two modems, transcievers, a Vtuc and a Vtur."
        SYNTAX  INTEGER
            {
            vtuc(1),
            Vtur.  Attributes with this syntax reference the two sides
            of a line.  Specified as an INTEGER, the two values are:

            vtuc(1)  -- central site modem transceiver
            vtur(2)  -- remote site modem transceiver"
        SYNTAX  INTEGER
            {
            vtuc(1),
            vtur(2)
            }

    --
    -- objects
    --

    vdslLineTable OBJECT-TYPE
        SYNTAX       SEQUENCE OF VdslLineEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "This table includes common attributes describing
            both ends of the line.  It is required for all VDSL
            physical interfaces.  VDSL physical interfaces are
            those ifEntries where ifType is equal to vdsl(97)."
        ::= { vdslMibObjects 1 }

    vdslLineEntry OBJECT-TYPE
        SYNTAX       VdslLineEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION  "An entry in the vdslLineTable."
        INDEX { ifIndex }
        ::= { vdslLineTable 1 }

    VdslLineEntry ::=
        SEQUENCE
            {
            vdslLineCoding                 VdslLineCodingType,
            vdslLineType                   INTEGER,
            vdslLineConfProfile            SnmpAdminString,
            vdslLineAlarmConfProfile       SnmpAdminString
            }

    vdslLineCoding OBJECT-TYPE
        SYNTAX       VdslLineCodingType
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Specifies the VDSL coding type used on this line."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslLineEntry 1 }

    vdslLineType OBJECT-TYPE
        SYNTAX       INTEGER
            {
            noChannel(1),         -- no channels exist
            fastOnly(2),          -- only fast channel only
            slowOnly(3), exists
            interleavedOnly(3),   -- slow channel only
            either(4), interleaved channel exists
            fastOrInterleaved(4), -- either fast or slow interleaved channel exist
            both(5)
                                  -- exist, but only one at a time
            fastAndInterleaved(5) -- both fast and slow interleaved channels
                                  -- exist
            }
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Defines the type of VDSL physical line entity that exists,
            by defining whether and how the line is channelized.  If
            the line is channelized,  the value will be other than
            noChannel(1).  This object defines which channel type(s)
            are supported.  Defined values are:

            noChannel(1)          -- no channels exist
            fastOnly(2)           -- only fast channel exists
            interleavedOnly(3)    -- only interleaved channel exists
            fastOrInterleaved(4)  -- either fast or interleaved channel
                                  -- exist, but only one at a time
            fastAndInterleaved(5) -- both fast and interleaved channels
                                  -- exist

            In the case that the line is channelized, the manager
            can use the ifStackTable to determine the ifIndex for
            the associated channel(s).

            Note that slow and interleaved refer to the same
            channel." channel(s)."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslLineEntry 2 }

    vdslLineConfProfile OBJECT-TYPE
        SYNTAX       SnmpAdminString (SIZE(1..32))
        MAX-ACCESS   read-write
        STATUS       current
        DESCRIPTION
            "The value of this object identifies the row
            in the VDSL Line Configuration Profile Table,
            ( vdslLineConfProfileTable ),
            vdslLineConfProfileTable, which applies for this
            VDSL line, and channels if applicable."
        DEFVAL       { "DEFVAL" }
        ::= { vdslLineEntry 3 }

    vdslLineAlarmConfProfile OBJECT-TYPE
        SYNTAX       SnmpAdminString (SIZE(1..32))
        MAX-ACCESS   read-write
        STATUS       current
        DESCRIPTION
            "The value of this object identifies the row in the VDSL
            Line Alarm Configuration Profile Table,
            ( vdslLineAlarmConfProfileTable ),
            vdslLineAlarmConfProfileTable, which applies to this
            VDSL line, and channels if applicable."
        DEFVAL       { "DEFVAL" }
        ::= { vdslLineEntry 4 }

    vdslPhysTable OBJECT-TYPE
        SYNTAX       SEQUENCE OF VdslPhysEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "This table provides one row for each Vtu.  Each row
            contains the Physical Layer Parameters table for that
            Vtu.  VDSL physical interfaces are those ifEntries where
            ifType is equal to vdsl(97)."
        ::= { vdslMibObjects 2 }

    vdslPhysEntry OBJECT-TYPE
        SYNTAX       VdslPhysEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION  "An entry in the vdslPhysTable."
        INDEX { ifIndex,
                vdslPhysSide }
        ::= { vdslPhysTable 1 }

    VdslPhysEntry ::=
        SEQUENCE
            {
            vdslPhysSide                   VdslLineEntity,
            vdslInvSerialNumber            SnmpAdminString,
            vdslInvVendorID                SnmpAdminString,
            vdslInvVersionNumber           SnmpAdminString,
            vdslCurrSnrMgn                 Integer32,
            vdslCurrAtn                    Gauge32,
            vdslCurrStatus                 BITS,
            vdslCurrOutputPwr              Integer32,
            vdslCurrAttainableRate         Gauge32,
            vdslCurrLineRate               Gauge32
            }

    vdslPhysSide OBJECT-TYPE
        SYNTAX       VdslLineEntity
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "Identifies whether the modem transceiver is the Vtuc or Vtur."
        ::= { vdslPhysEntry 1 }

    vdslInvSerialNumber OBJECT-TYPE
        SYNTAX       SnmpAdminString(SIZE (0..32))
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "The vendor specific string that identifies the
            vendor equipment."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPhysEntry 2 }

    vdslInvVendorID OBJECT-TYPE
        SYNTAX       SnmpAdminString (SIZE (0..16))
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "The vendor ID code is a copy of the binary vendor
            identification field expressed as readable characters." characters
            in hexadecimal notation."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPhysEntry 3 }

    vdslInvVersionNumber OBJECT-TYPE
        SYNTAX       SnmpAdminString (SIZE (0..16))
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "The vendor specific version number sent by this Vtu
            as part of the initialization messages.  It is a copy
            of the binary version number field expressed as
            readable characters." characters in hexadecimal notation."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPhysEntry 4 }

    vdslCurrSnrMgn OBJECT-TYPE
        SYNTAX       Integer32 (-127..127)
        UNITS        "0.25dBm"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Noise Margin as seen by this Vtu with respect to its
            received signal in 0.25dB.  The effective range is
            -31.75 to +31.75dB." +31.75 dB."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
         ::= { vdslPhysEntry 5 }

    vdslCurrAtn OBJECT-TYPE
        SYNTAX       Gauge32 (0..255)
        UNITS        "0.25dBm"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Measured difference in the total power transmitted by
            the peer Vtu and the total power received by this Vtu.
            The effective range is 0 to +63.75dB." +63.75 dB."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
         ::= { vdslPhysEntry 6 }

    vdslCurrStatus OBJECT-TYPE
        SYNTAX       BITS
            {
            noDefect(0),
            lossOfFraming(1),
            lossOfSignal(2),
            lossOfPower(3),
            lossOfSignalQuality(4),
            lossOfLink(5),
            dataInitFailure(6),
            configInitFailure(7),
            protocolInitFailure(8),
            noPeerVtuPresent(9)
            }
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION
            "Indicates current state of the Vtu line.  This is a
            bit-map of possible conditions.  The various bit
            positions are:

            0   noDefect             There are no defects on the line line.

            1   lossOfFraming        Vtu failure due to not receiving
                                     a valid frame.

            2   lossOfSignal         Vtu failure due to not receiving
                                     signal.

            3   lossOfPower          Vtu failure due to loss of power.

            4   lossOfSignalQuality  Loss of Signal Quality is declared
                                     when the Noise Margin falls below
                                     the Minimum Noise Margin, or the
                                     bit-error-rate exceeds 10^-7.

            5   lossOfLink           Vtu failure due to inability to
                                     link with peer Vtu.  Set whenever
                                     the transceiver is in the 'Warm
                                     Start' state.

            6   dataInitFailure      Vtu failure during initialization
                                     due to bit errors corrupting
                                     startup exchange data.

            7   configInitFailure    Vtu failure during initialization
                                     due to peer Vtu not able to
                                     support requested configuration.

            8   protocolInitFailure  Vtu failure during initialization
                                     due to incompatible protocol used
                                     by the peer Vtu.

            9   noPeerVtuPresent     Vtu failure during initialization
                                     due to no activation sequence
                                     detected from peer Vtu.

            This is intended to supplement ifOperStatus."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
         ::= { vdslPhysEntry 7 }

    vdslCurrOutputPwr OBJECT-TYPE
        SYNTAX       Integer32 (0..160)
        UNITS        "0.1dBm"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Measured total output power transmitted by this VTU.
            This is the measurement that was reported during
            the last activation sequence."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPhysEntry 8 }

    vdslCurrAttainableRate OBJECT-TYPE
        SYNTAX       Gauge32
        UNITS        "kbps"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Indicates the maximum currently attainable data rate
            in steps of 1000 bits/second by the Vtu.  This value
            will be equal to or greater than vdslCurrLineRate.
            Note that for SCM, the minimum and maximum data rates
            are equal.  Note: 1 kbps = 1000 bps."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPhysEntry 9 }
    vdslCurrLineRate OBJECT-TYPE
        SYNTAX       Gauge32
        UNITS        "kbps"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Indicates the current data rate in steps of 1000
            bits/second by the Vtu.  This value will be less than
            or equal to vdslCurrAttainableRate.  Note: 1 kbps =
            1000 bps."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPhysEntry 10 }

    vdslChanTable OBJECT-TYPE
        SYNTAX       SEQUENCE OF VdslChanEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "This table provides one row for each Vtu channel.
            VDSL channel interfaces are those ifEntries where
            ifType is equal to interleave(124) or fast(125)."
        ::= { vdslMibObjects 3 }

    vdslChanEntry OBJECT-TYPE
        SYNTAX       VdslChanEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "An entry in the vdslChanTable."
        INDEX { ifIndex,
                vdslPhysSide }
        ::= { vdslChanTable 1 }

    VdslChanEntry ::=
        SEQUENCE
            {
            vdslChanInterleaveDelay        Gauge32,
            vdslChanCrcBlockLength         Gauge32,
            vdslChanCurrTxRate             Gauge32,
            vdslChanCurrTxSlowBurstProtection
            vdslChanCurrTxSlowBurstProtect Gauge32,
            vdslChanCurrTxFastFecOverhead
            vdslChanCurrTxFastFec          Gauge32
            }

    vdslChanInterleaveDelay OBJECT-TYPE
        SYNTAX       Gauge32
        UNITS        "ms"        "milliseconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Interleave Delay for this channel.

            Interleave delay applies only to the interleave
            (slow) channel and defines the mapping (relative
            spacing) between subsequent input bytes at the
            interleaver input and their placement in the bit
            stream at the interleaver output.  Larger numbers
            provide greater separation between consecutive
            input bytes in the output bit stream allowing for
            improved impulse noise immunity at the expense of
            payload latency.

            In the case where the ifType is fast(125), use
            noSuchObject." return
            a value of zero."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslChanEntry 1 }

    vdslChanCrcBlockLength OBJECT-TYPE
        SYNTAX       Gauge32
        UNITS        "byte"        "bytes"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Indicates the length of the channel data-block
            on which the CRC operates."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslChanEntry 2 }

    vdslChanCurrTxRate OBJECT-TYPE
        SYNTAX       Gauge32
        UNITS        "kbps"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Actual transmit data rate on this channel.  Note: 1
            kbps = 1000 bps."
        ::= { vdslChanEntry 3 }

    vdslChanCurrTxSlowBurstProtection

    vdslChanCurrTxSlowBurstProtect OBJECT-TYPE
        SYNTAX       Gauge32 (0..1275)
        UNITS        "microseconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Actual level of impulse noise (burst) protection
            for an interleaved (slow) channel.  This parameter is
            not applicable to fast channels.  For fast channels,
            a value of zero shall be returned."
        REFERENCE    "ITU-T G.997.1"          -- G.997.1, section 7.3.2.3 7.3.2.3"
        ::= { vdslChanEntry 4 }

    vdslChanCurrTxFastFecOverhead

    vdslChanCurrTxFastFec OBJECT-TYPE
        SYNTAX       Gauge32 (0..50)
        UNITS        "%"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Actual Forward Error Correction (FEC) redundancy
            related overhead for a fast channel.  This parameter
            is not applicable to an interleaved (slow) channel.
            For interleaved channels, a value of zero shall be
            returned."
        ::= { vdslChanEntry 5 }

    vdslPerfDataTable       OBJECT-TYPE
        SYNTAX       SEQUENCE OF VdslPerfDataEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "This table provides one row for each VDSL physical
            interface.  VDSL physical interfaces are those ifEntries
            where ifType is equal to vdsl(97)."
        ::= { vdslMibObjects 4 }

    vdslPerfDataEntry       OBJECT-TYPE
        SYNTAX        VdslPerfDataEntry
        MAX-ACCESS    not-accessible
        STATUS        current
        DESCRIPTION
            "An entry in the vdslPerfDataTable."
        INDEX { ifIndex,
                vdslPhysSide }
        ::= { vdslPerfDataTable 1 }

    VdslPerfDataEntry ::=
        SEQUENCE
            {
            vdslPerfValidIntervals         HCPerfValidIntervals,
            vdslPerfInvalidIntervals       HCPerfInvalidIntervals,
            vdslPerfLofs                       Counter64,                   Unsigned32,
            vdslPerfLoss                       Counter64,                   Unsigned32,
            vdslPerfLprs                       Counter64,                   Unsigned32,
            vdslPerfLols                       Counter64,                   Unsigned32,
            vdslPerfESs                        Counter64,                    Unsigned32,
            vdslPerfSESs                       Counter64,                   Unsigned32,
            vdslPerfUASs                       Counter64,                   Unsigned32,
            vdslPerfInits                      Counter64,                  Unsigned32,
            vdslPerfCurr15MinTimeElapsed   HCPerfTimeElapsed,
            vdslPerfCurr15MinLofs          HCPerfCurrentCount,
            vdslPerfCurr15MinLoss          HCPerfCurrentCount,
            vdslPerfCurr15MinLprs          HCPerfCurrentCount,
            vdslPerfCurr15MinLols          HCPerfCurrentCount,
            vdslPerfCurr15MinESs           HCPerfCurrentCount,
            vdslPerfCurr15MinSESs          HCPerfCurrentCount,
            vdslPerfCurr15MinUASs          HCPerfCurrentCount,
            vdslPerfCurr15MinInits         HCPerfCurrentCount,
            vdslPerf1DayValidIntervals     HCPerfValidIntervals,
            vdslPerf1DayInvalidIntervals   HCPerfInvalidIntervals,
            vdslPerfCurr1DayTimeElapsed    HCPerfTimeElapsed,
            vdslPerfCurr1DayLofs               Counter64,           Unsigned32,
            vdslPerfCurr1DayLoss               Counter64,           Unsigned32,
            vdslPerfCurr1DayLprs               Counter64,           Unsigned32,
            vdslPerfCurr1DayLols               Counter64,           Unsigned32,
            vdslPerfCurr1DayESs                Counter64,            Unsigned32,
            vdslPerfCurr1DaySESs               Counter64,           Unsigned32,
            vdslPerfCurr1DayUASs               Counter64,           Unsigned32,
            vdslPerfCurr1DayInits              Counter64          Unsigned32
            }

    vdslPerfValidIntervals OBJECT-TYPE
        SYNTAX       HCPerfValidIntervals
        UNITS        "intervals"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Valid Intervals per definition found in
            HC-PerfHist-TC-MIB."
        ::= { vdslPerfDataEntry 1 }

    vdslPerfInvalidIntervals OBJECT-TYPE
        SYNTAX       HCPerfInvalidIntervals
        UNITS        "intervals"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Invalid Intervals per definition found in
            HC-PerfHist-TC-MIB."
        ::= { vdslPerfDataEntry 2 }

    vdslPerfLofs OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of seconds since the unit was last reset that there
            was Loss of Framing."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPerfDataEntry 3 }

    vdslPerfLoss OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of seconds since the unit was last reset that there
            was Loss of Signal."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPerfDataEntry 4 }

    vdslPerfLprs OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of seconds since the unit was last reset that there
            was Loss of Power."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPerfDataEntry 5 }

    vdslPerfLols OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of seconds since the unit was last reset that there
            was Loss of Link."
        ::= { vdslPerfDataEntry 6 }

    vdslPerfESs OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of Errored Seconds since the unit was last reset.
            An Errored Second is a one-second interval containing one
            or more crc CRC anomalies, or one or more los LOS or lof LOF defects."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPerfDataEntry 7 }

    vdslPerfSESs OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of Severely Errored Seconds since the unit was last
            reset."
        ::= { vdslPerfDataEntry 8 }

    vdslPerfUASs OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of Unavailable Seconds since the unit was last
            reset."
        ::= { vdslPerfDataEntry 9 }

    vdslPerfInits OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "occurences"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of the line initialization attempts since the unit
            was last reset.  This count includes both successful and
            failed attempts."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPerfDataEntry 10 }

    vdslPerfCurr15MinTimeElapsed OBJECT-TYPE
        SYNTAX       HCPerfTimeElapsed
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Total elapsed seconds in this interval."
        ::= { vdslPerfDataEntry 11 }

    vdslPerfCurr15MinLofs OBJECT-TYPE
        SYNTAX       HCPerfCurrentCount
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of seconds during this interval that there
            was Loss of Framing."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPerfDataEntry 12 }

    vdslPerfCurr15MinLoss OBJECT-TYPE
        SYNTAX       HCPerfCurrentCount
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of seconds during this interval that there
            was Loss of Signal."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPerfDataEntry 13 }

    vdslPerfCurr15MinLprs OBJECT-TYPE
        SYNTAX       HCPerfCurrentCount
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of seconds during this interval that there
            was Loss of Power."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPerfDataEntry 14 }

    vdslPerfCurr15MinLols OBJECT-TYPE
        SYNTAX       HCPerfCurrentCount
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of seconds during this interval that there
            was Loss of Link."
        ::= { vdslPerfDataEntry 15 }

    vdslPerfCurr15MinESs OBJECT-TYPE
        SYNTAX       HCPerfCurrentCount
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of Errored Seconds during this interval.  An Errored
            Second is a one-second interval containing one or more crc CRC
            anomalies, or one or more los LOS or lof LOF defects."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPerfDataEntry 16 }

    vdslPerfCurr15MinSESs OBJECT-TYPE
        SYNTAX       HCPerfCurrentCount
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of Severely Errored Seconds during this interval."
        ::= { vdslPerfDataEntry 17 }

    vdslPerfCurr15MinUASs OBJECT-TYPE
        SYNTAX       HCPerfCurrentCount
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of Unavailable Seconds during this interval."
        ::= { vdslPerfDataEntry 18 }

    vdslPerfCurr15MinInits OBJECT-TYPE
        SYNTAX       HCPerfCurrentCount
        UNITS        "occurences"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of the line initialization attempts during this
            interval.  This count includes both successful and
            failed attempts."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPerfDataEntry 19 }

    vdslPerf1DayValidIntervals OBJECT-TYPE
        SYNTAX       HCPerfValidIntervals
        UNITS        "intervals"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Valid Intervals per definition found in
            HC-PerfHist-TC-MIB."
        ::= { vdslPerfDataEntry 20 }

    vdslPerf1DayInvalidIntervals OBJECT-TYPE
        SYNTAX       HCPerfInvalidIntervals
        UNITS        "intervals"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Invalid Intervals per definition found in
            HC-PerfHist-TC-MIB."
        ::= { vdslPerfDataEntry 21 }

    vdslPerfCurr1DayTimeElapsed OBJECT-TYPE
        SYNTAX       HCPerfTimeElapsed
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
             "Number of seconds that have elapsed since the beginning
             of the current 1-day interval."
        ::= { vdslPerfDataEntry 22 }

    vdslPerfCurr1DayLofs OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of Loss of Framing (LOF) Seconds since the
            beginning of the current 1-day interval."
        ::= { vdslPerfDataEntry 23 }

    vdslPerfCurr1DayLoss OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of Loss of Signal (LOS) Seconds since the beginning
            of the current 1-day interval."
        ::= { vdslPerfDataEntry 24 }

    vdslPerfCurr1DayLprs OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of Loss of Power (LPR) Seconds since the beginning
            of the current 1-day interval."
        ::= { vdslPerfDataEntry 25 }

    vdslPerfCurr1DayLols OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of Loss of Link (LOL) Seconds since the beginning
            of the current 1-day interval."
        ::= { vdslPerfDataEntry 26 }

    vdslPerfCurr1DayESs OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of Errored Seconds (ES) since the beginning
            of the current 1-day interval."
        ::= { vdslPerfDataEntry 27 }

    vdslPerfCurr1DaySESs OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of Severely Errored Seconds (SES) since the
            beginning of the current 1-day interval."
        ::= { vdslPerfDataEntry 28 }

    vdslPerfCurr1DayUASs OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of Unavailable Seconds (UAS) since the beginning
            of the current 1-day interval."
        ::= { vdslPerfDataEntry 29 }
    vdslPerfCurr1DayInits OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of the line initialization attempts since the
            beginning of the current 1-day interval.  This count
            includes both successful and failed attempts."
        ::= { vdslPerfDataEntry 30 }

    vdslPerfIntervalTable       OBJECT-TYPE
        SYNTAX       SEQUENCE OF VdslPerfIntervalEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "This table provides one row for each Vtu performance
            data collection interval.  VDSL physical interfaces are
            those ifEntries where ifType is equal to vdsl(97)."
        ::= { vdslMibObjects 5 }

    vdslPerfIntervalEntry       OBJECT-TYPE
        SYNTAX        VdslPerfIntervalEntry
        MAX-ACCESS    not-accessible
        STATUS        current
        DESCRIPTION
            "An entry in the vdslPerfIntervalTable."
        INDEX { ifIndex,
                vdslPhysSide,
                vdslIntervalNumber }
        ::= { vdslPerfIntervalTable 1 }

    VdslPerfIntervalEntry ::=
        SEQUENCE
            {
            vdslIntervalNumber             Unsigned32,
            vdslIntervalLofs               HCPerfIntervalCount,
            vdslIntervalLoss               HCPerfIntervalCount,
            vdslIntervalLprs               HCPerfIntervalCount,
            vdslIntervalLols               HCPerfIntervalCount,
            vdslIntervalESs                HCPerfIntervalCount,
            vdslIntervalSESs               HCPerfIntervalCount,
            vdslIntervalUASs               HCPerfIntervalCount,
            vdslIntervalInits              HCPerfIntervalCount
            }

    vdslIntervalNumber OBJECT-TYPE
        SYNTAX       Unsigned32 (1..96)
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "Performance Data Interval number 1 is the the most recent
            previous interval; interval 96 is 24 hours ago.
            Intervals 2..96 2 to 96 are optional."
        ::= { vdslPerfIntervalEntry 1 }

    vdslIntervalLofs OBJECT-TYPE
        SYNTAX       HCPerfIntervalCount
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of seconds in the interval when there was Loss
            of Framing."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPerfIntervalEntry 2 }

    vdslIntervalLoss OBJECT-TYPE
        SYNTAX       HCPerfIntervalCount
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of seconds in the interval when there was Loss
            of Signal."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPerfIntervalEntry 3 }

    vdslIntervalLprs OBJECT-TYPE
        SYNTAX       HCPerfIntervalCount
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of seconds in the interval when there was Loss
            of Power."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPerfIntervalEntry 4 }

    vdslIntervalLols OBJECT-TYPE
        SYNTAX       HCPerfIntervalCount
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of seconds in the interval when there was Loss
            of Link."
        ::= { vdslPerfIntervalEntry 5 }

    vdslIntervalESs OBJECT-TYPE
        SYNTAX       HCPerfIntervalCount
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of Errored Seconds (ES) in the interval.  An Errored
            Second is a one-second interval containing one or more crc CRC
            anomalies, one or more los LOS or lof LOF defects."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPerfIntervalEntry 6 }

    vdslIntervalSESs OBJECT-TYPE
        SYNTAX       HCPerfIntervalCount
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of Severely Errored Seconds in the interval."
        ::= { vdslPerfIntervalEntry 7 }

    vdslIntervalUASs OBJECT-TYPE
        SYNTAX       HCPerfIntervalCount
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of Unavailable Seconds in the interval."
        ::= { vdslPerfIntervalEntry 8 }

    vdslIntervalInits OBJECT-TYPE
        SYNTAX       HCPerfIntervalCount
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of the line initialization attempts during this
            interval.  This count includes both successful and
            failed attempts."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslPerfIntervalEntry 9 }

    vdsl1DayIntervalTable OBJECT-TYPE
        SYNTAX       SEQUENCE OF Vdsl1DayIntervalEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "This table provides one row for each VDSL performance
            data collection interval.  This table contains live data
            from equipment.  As such, it is NOT persistent."
        ::= { vdslMibObjects 6 }

    vdsl1DayIntervalEntry OBJECT-TYPE
        SYNTAX       Vdsl1DayIntervalEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "An entry in the vdsl1DayIntervalTable."
        INDEX { ifIndex,
                vdslPhysSide,
                vdsl1DayIntervalNumber }
        ::= { vdsl1DayIntervalTable 1 }

    Vdsl1DayIntervalEntry ::=
        SEQUENCE
        {
        vdsl1DayIntervalNumber             Unsigned32,
        vdsl1DayIntervalMoniSecs           HCPerfTimeElapsed,
        vdsl1DayIntervalLofs                   Counter64,               Unsigned32,
        vdsl1DayIntervalLoss                   Counter64,               Unsigned32,
        vdsl1DayIntervalLprs                   Counter64,               Unsigned32,
        vdsl1DayIntervalLols                   Counter64,               Unsigned32,
        vdsl1DayIntervalESs                    Counter64,                Unsigned32,
        vdsl1DayIntervalSESs                   Counter64,               Unsigned32,
        vdsl1DayIntervalUASs                   Counter64,               Unsigned32,
        vdsl1DayIntervalInits                  Counter64              Unsigned32
        }

    vdsl1DayIntervalNumber OBJECT-TYPE
        SYNTAX       Unsigned32 (1..30)
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "History Data Interval number.  Interval 1 is the the most
            recent previous day; interval 30 is 30 days ago.  Intervals
            2..30
            2 to 30 are optional."
        ::= { vdsl1DayIntervalEntry 1 }

    vdsl1DayIntervalMoniSecs OBJECT-TYPE
        SYNTAX       HCPerfTimeElapsed
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "The amount of time in the 1-day interval over which the
            performance monitoring information is actually counted.
            This value will be the same as the interval duration except
            in a situation where performance monitoring data could not
            be collected for any reason."
        ::= { vdsl1DayIntervalEntry 2 }

    vdsl1DayIntervalLofs OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
             "Count of Loss of Frame (LOF) Seconds during the 1-day
             interval as measured by vdsl1DayIntervalMoniSecs."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdsl1DayIntervalEntry 3 }

    vdsl1DayIntervalLoss OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
             "Count of Loss of Signal (LOS) Seconds during the 1-day
             interval as measured by vdsl1DayIntervalMoniSecs."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdsl1DayIntervalEntry 4 }

    vdsl1DayIntervalLprs OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
             "Count of Loss of Power (LPR) Seconds during the 1-day
             interval as measured by vdsl1DayIntervalMoniSecs."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdsl1DayIntervalEntry 5 }

    vdsl1DayIntervalLols OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
             "Count of Loss of Link (LOL) Seconds during the 1-day
             interval as measured by vdsl1DayIntervalMoniSecs."
        ::= { vdsl1DayIntervalEntry 6 }

    vdsl1DayIntervalESs OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
             "Count of Errored Seconds (ES) during the 1-day
             interval as measured by vdsl1DayIntervalMoniSecs."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdsl1DayIntervalEntry 7 }

    vdsl1DayIntervalSESs OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
             "Count of Severely Errored Seconds (SES) during the 1-day
             interval as measured by vdsl1DayIntervalMoniSecs."
        ::= { vdsl1DayIntervalEntry 8 }

    vdsl1DayIntervalUASs OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
             "Count of Unavailable Seconds (UAS) during the 1-day
             interval as measured by vdsl1DayIntervalMoniSecs."
        ::= { vdsl1DayIntervalEntry 9 }

    vdsl1DayIntervalInits OBJECT-TYPE
        SYNTAX       Counter64       Unsigned32
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "Count of the line initialization attempts during the
            1-day interval as measured by vdsl1DayIntervalMoniSecs.
            This count includes both successful and failed attempts."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdsl1DayIntervalEntry 10 }

    vdslChanPerfDataTable       OBJECT-TYPE
        SYNTAX       SEQUENCE OF VdslChanPerfDataEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "This table provides one row for each Vtu channel.
            VDSL channel interfaces are those ifEntries where
            ifType is equal to interleave(124) or fast(125)."
        ::= { vdslMibObjects 7 }

    vdslChanPerfDataEntry OBJECT-TYPE
        SYNTAX        VdslChanPerfDataEntry
        MAX-ACCESS    not-accessible
        STATUS        current
        DESCRIPTION
            "An entry in the vdslChanPerfDataTable."
        INDEX { ifIndex,
                vdslPhysSide }
        ::= { vdslChanPerfDataTable 1 }

    VdslChanPerfDataEntry ::=
        SEQUENCE
            {
            vdslChanPerfValidIntervals
            vdslChanValidIntervals         HCPerfValidIntervals,
            vdslChanPerfInvalidIntervals
            vdslChanInvalidIntervals       HCPerfInvalidIntervals,
            vdslChanCorrectedOctets                Counter64,
            vdslChanUncorrectableBlks              Counter64,
            vdslChanPerfCurr15MinTimeElapsed
            vdslChanFixedOctets            ZeroBasedCounter64,
            vdslChanBadBlks                ZeroBasedCounter64,
            vdslChanCurr15MinTimeElapsed   HCPerfTimeElapsed,
            vdslChanPerfCurr15MinCorrectedOctets
            vdslChanCurr15MinFixedOctets   HCPerfCurrentCount,
            vdslChanPerfCurr15MinUncorrectableBlks
            vdslChanCurr15MinBadBlks       HCPerfCurrentCount,
            vdslChanPerf1DayValidIntervals
            vdslChan1DayValidIntervals     HCPerfValidIntervals,
            vdslChanPerf1DayInvalidIntervals
            vdslChan1DayInvalidIntervals   HCPerfInvalidIntervals,
            vdslChanPerfCurr1DayTimeElapsed
            vdslChanCurr1DayTimeElapsed    HCPerfTimeElapsed,
            vdslChanPerfCurr1DayCorrectedOctets
            vdslChanCurr1DayFixedOctets    HCPerfCurrentCount,
            vdslChanPerfCurr1DayUncorrectableBlks
            vdslChanCurr1DayBadBlks        HCPerfCurrentCount
            }

    vdslChanPerfValidIntervals

    vdslChanValidIntervals OBJECT-TYPE
        SYNTAX        HCPerfValidIntervals
        UNITS        "intervals"
        MAX-ACCESS    read-only
        STATUS        current
        DESCRIPTION
            "Valid Intervals per definition found in
            HC-PerfHist-TC-MIB."
        ::= { vdslChanPerfDataEntry 1 }

    vdslChanPerfInvalidIntervals

    vdslChanInvalidIntervals OBJECT-TYPE
        SYNTAX        HCPerfInvalidIntervals
        UNITS        "intervals"
        MAX-ACCESS    read-only
        STATUS        current
        DESCRIPTION
            "Invalid Intervals per definition found in
            HC-PerfHist-TC-MIB."
        ::= { vdslChanPerfDataEntry 2 }

    vdslChanCorrectedOctets

    vdslChanFixedOctets OBJECT-TYPE
        SYNTAX        Counter64        ZeroBasedCounter64
        UNITS         "octets"
        MAX-ACCESS    read-only
        STATUS        current
        DESCRIPTION
            "Count of corrected octets since the unit was last reset."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslChanPerfDataEntry 3 }
    vdslChanUncorrectableBlks

    vdslChanBadBlks OBJECT-TYPE
        SYNTAX        Counter64        ZeroBasedCounter64
        UNITS         "blocks"
        MAX-ACCESS    read-only
        STATUS        current
        DESCRIPTION
            "Count of uncorrectable blocks since the unit was last
            reset."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslChanPerfDataEntry 4 }

    vdslChanPerfCurr15MinTimeElapsed
    vdslChanCurr15MinTimeElapsed OBJECT-TYPE
        SYNTAX        HCPerfTimeElapsed
        UNITS         "seconds"
        MAX-ACCESS    read-only
        STATUS        current
        DESCRIPTION
            "Total elapsed seconds in this interval."
        ::= { vdslChanPerfDataEntry 5 }

    vdslChanPerfCurr15MinCorrectedOctets

    vdslChanCurr15MinFixedOctets OBJECT-TYPE
        SYNTAX        HCPerfCurrentCount
        UNITS         "octets"
        MAX-ACCESS    read-only
        STATUS        current
        DESCRIPTION
            "Count of corrected octets in this interval."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslChanPerfDataEntry 6 }

    vdslChanPerfCurr15MinUncorrectableBlks

    vdslChanCurr15MinBadBlks OBJECT-TYPE
        SYNTAX        HCPerfCurrentCount
        UNITS         "blocks"
        MAX-ACCESS    read-only
        STATUS        current
        DESCRIPTION
            "Count of uncorrectable blocks in this interval."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslChanPerfDataEntry 7 }

    vdslChanPerf1DayValidIntervals

    vdslChan1DayValidIntervals OBJECT-TYPE
        SYNTAX        HCPerfValidIntervals
        MAX-ACCESS    read-only
        STATUS        current
        DESCRIPTION
            "Valid Intervals per definition found in
            HC-PerfHist-TC-MIB."
        ::= { vdslChanPerfDataEntry 8 }

    vdslChanPerf1DayInvalidIntervals

    vdslChan1DayInvalidIntervals OBJECT-TYPE
        SYNTAX        HCPerfInvalidIntervals
        MAX-ACCESS    read-only
        STATUS        current
        DESCRIPTION
            "Invalid Intervals per definition found in
            HC-PerfHist-TC-MIB."
        ::= { vdslChanPerfDataEntry 9 }
    vdslChanPerfCurr1DayTimeElapsed

    vdslChanCurr1DayTimeElapsed OBJECT-TYPE
        SYNTAX       HCPerfTimeElapsed
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
             "Number of seconds that have elapsed since the beginning
             of the current 1-day interval."
        ::= { vdslChanPerfDataEntry 10 }

    vdslChanPerfCurr1DayCorrectedOctets

    vdslChanCurr1DayFixedOctets OBJECT-TYPE
        SYNTAX        HCPerfCurrentCount
        UNITS         "octets"
        MAX-ACCESS    read-only
        STATUS        current
        DESCRIPTION
            "Count of corrected octets since the beginning of the
            current 1-day interval."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslChanPerfDataEntry 11 }

    vdslChanPerfCurr1DayUncorrectableBlks

    vdslChanCurr1DayBadBlks OBJECT-TYPE
        SYNTAX        HCPerfCurrentCount
        UNITS         "blocks"
        MAX-ACCESS    read-only
        STATUS        current
        DESCRIPTION
            "Count of uncorrectable blocks since the beginning of the
            current 1-day interval."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslChanPerfDataEntry 12 }

    vdslChanIntervalTable       OBJECT-TYPE
        SYNTAX       SEQUENCE OF VdslChanIntervalEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "This table provides one row for each Vtu channel data
            collection interval.  VDSL channel interfaces are those
            ifEntries where ifType is equal to interleave(124) or
            fast(125)."
        ::= { vdslMibObjects 8 }

    vdslChanIntervalEntry OBJECT-TYPE
        SYNTAX        VdslChanIntervalEntry
        MAX-ACCESS    not-accessible
        STATUS        current
        DESCRIPTION
            "An entry in the vdslChanIntervalTable."
        INDEX { ifIndex,
                vdslPhysSide,
                vdslChanIntervalNumber }
        ::= { vdslChanIntervalTable 1 }

    VdslChanIntervalEntry ::=
        SEQUENCE
            {
            vdslChanIntervalNumber         Unsigned32,
            vdslChanIntervalCorrectedOctets
            vdslChanIntervalFixedOctets    HCPerfIntervalCount,
            vdslChanIntervalUncorrectableBlks
            vdslChanIntervalBadBlks        HCPerfIntervalCount
            }

    vdslChanIntervalNumber OBJECT-TYPE
        SYNTAX        Unsigned32 (0..96) (1..96)
        MAX-ACCESS    not-accessible
        STATUS        current
        DESCRIPTION
            "Performance Data Interval number 1 is the the most recent
            previous interval; interval 96 is 24 hours ago.
            Intervals 2..96 2 to 96 are optional."
        ::= { vdslChanIntervalEntry 1 }

    vdslChanIntervalCorrectedOctets

    vdslChanIntervalFixedOctets OBJECT-TYPE
        SYNTAX        HCPerfIntervalCount
        UNITS        "octets"
        MAX-ACCESS    read-only
        STATUS        current
        DESCRIPTION
            "Count of corrected octets in this interval."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslChanIntervalEntry 2 }

    vdslChanIntervalUncorrectableBlks

    vdslChanIntervalBadBlks OBJECT-TYPE
        SYNTAX        HCPerfIntervalCount
        UNITS        "blocks"
        MAX-ACCESS    read-only
        STATUS        current
        DESCRIPTION
            "Count of uncorrectable blocks in this interval."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslChanIntervalEntry 3 }

    vdslChan1DayIntervalTable OBJECT-TYPE
        SYNTAX       SEQUENCE OF VdslChan1DayIntervalEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "This table provides one row for each VDSL performance
            data collection interval.  This table contains live data
            from equipment.  As such, it is NOT persistent."
        ::= { vdslMibObjects 9 }

    vdslChan1DayIntervalEntry OBJECT-TYPE
        SYNTAX       VdslChan1DayIntervalEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "An entry in the vdslChan1DayIntervalTable."
        INDEX { ifIndex,
                vdslPhysSide,
                vdslChan1DayIntervalNumber }
        ::= { vdslChan1DayIntervalTable 1 }

    VdslChan1DayIntervalEntry ::=
        SEQUENCE
        {
        vdslChan1DayIntervalNumber         Unsigned32,
        vdslChan1DayIntervalMoniSecs       HCPerfTimeElapsed,
        vdslChan1DayIntervalCorrectedOctets
        vdslChan1DayIntervalFixedOctets    HCPerfCurrentCount,
        vdslChan1DayIntervalUncorrectableBlks
        vdslChan1DayIntervalBadBlks        HCPerfCurrentCount
        }

    vdslChan1DayIntervalNumber OBJECT-TYPE
        SYNTAX       Unsigned32 (1..30)
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "History Data Interval number.  Interval 1 is the the most
            recent previous day; interval 30 is 30 days ago.  Intervals
            2..30
            2 to 30 are optional."
        ::= { vdslChan1DayIntervalEntry 1 }

    vdslChan1DayIntervalMoniSecs OBJECT-TYPE
        SYNTAX       HCPerfTimeElapsed
        UNITS        "seconds"
        MAX-ACCESS   read-only
        STATUS       current
        DESCRIPTION
            "The amount of time in the 1-day interval over which the
            performance monitoring information is actually counted.
            This value will be the same as the interval duration except
            in a situation where performance monitoring data could not
            be collected for any reason."
        ::= { vdslChan1DayIntervalEntry 2 }

    vdslChan1DayIntervalCorrectedOctets

    vdslChan1DayIntervalFixedOctets OBJECT-TYPE
        SYNTAX        HCPerfCurrentCount
        UNITS        "octets"
        MAX-ACCESS    read-only
        STATUS        current
        DESCRIPTION
            "Count of corrected octets in this interval."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslChan1DayIntervalEntry 3 }

    vdslChan1DayIntervalUncorrectableBlks

    vdslChan1DayIntervalBadBlks OBJECT-TYPE
        SYNTAX        HCPerfCurrentCount
        UNITS        "blocks"
        MAX-ACCESS    read-only
        STATUS        current
        DESCRIPTION
            "Count of uncorrectable blocks in this interval."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        ::= { vdslChan1DayIntervalEntry 4 }

    --
    -- profile tables
    --

    vdslLineConfProfileTable OBJECT-TYPE
        SYNTAX         SEQUENCE OF VdslLineConfProfileEntry
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
            "This table contains information on the VDSL line
            configuration.  One entry in this table reflects a
            profile defined by a manager which can be used to
            configure the VDSL line."
        ::= { vdslMibObjects 11 }

    vdslLineConfProfileEntry OBJECT-TYPE
        SYNTAX         VdslLineConfProfileEntry
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
            "Each entry consists of a list of parameters that
            represents the configuration of a VDSL line.

            A default profile with an index of 'DEFVAL', will
            always exist and its parameters will be set to vendor
            specific values, unless otherwise specified in this
            document."
        INDEX { vdslLineConfProfileName }
        ::= { vdslLineConfProfileTable 1 }

    VdslLineConfProfileEntry ::=
        SEQUENCE
            {
            vdslLineConfProfileName            SnmpAdminString,
            vdslLineConfDownstreamRateMode
            vdslLineConfDownRateMode           INTEGER,
            vdslLineConfUpstreamRateMode
            vdslLineConfUpRateMode             INTEGER,
            vdslLineConfDownstreamMaxPwr
            vdslLineConfDownMaxPwr             Unsigned32,
            vdslLineConfUpstreamMaxPwr
            vdslLineConfUpMaxPwr               Unsigned32,
            vdslLineConfDownstreamMaxSnrMgn
            vdslLineConfDownMaxSnrMgn          Unsigned32,
            vdslLineConfDownstreamMinSnrMgn
            vdslLineConfDownMinSnrMgn          Unsigned32,
            vdslLineConfDownstreamTargetSnrMgn
            vdslLineConfDownTargetSnrMgn       Unsigned32,
            vdslLineConfUpstreamMaxSnrMgn
            vdslLineConfUpMaxSnrMgn            Unsigned32,
            vdslLineConfUpstreamMinSnrMgn
            vdslLineConfUpMinSnrMgn            Unsigned32,
            vdslLineConfUpstreamTargetSnrMgn
            vdslLineConfUpTargetSnrMgn         Unsigned32,
            vdslLineConfDownstreamFastMaxDataRate
            vdslLineConfDownFastMaxDataRate    Unsigned32,
            vdslLineConfDownstreamFastMinDataRate
            vdslLineConfDownFastMinDataRate    Unsigned32,
            vdslLineConfDownstreamSlowMaxDataRate
            vdslLineConfDownSlowMaxDataRate    Unsigned32,
            vdslLineConfDownstreamSlowMinDataRate
            vdslLineConfDownSlowMinDataRate    Unsigned32,
            vdslLineConfUpstreamFastMaxDataRate
            vdslLineConfUpFastMaxDataRate      Unsigned32,
            vdslLineConfUpstreamFastMinDataRate
            vdslLineConfUpFastMinDataRate      Unsigned32,
            vdslLineConfUpstreamSlowMaxDataRate
            vdslLineConfUpSlowMaxDataRate      Unsigned32,
            vdslLineConfUpstreamSlowMinDataRate
            vdslLineConfUpSlowMinDataRate      Unsigned32,
            vdslLineConfDownstreamRateRatio
            vdslLineConfDownRateRatio          Unsigned32,
            vdslLineConfUpstreamRateRatio
            vdslLineConfUpRateRatio            Unsigned32,
            vdslLineConfDownstreamMaxInterDelay
            vdslLineConfDownMaxInterDelay      Unsigned32,
            vdslLineConfUpstreamMaxInterDelay
            vdslLineConfUpMaxInterDelay        Unsigned32,
            vdslLineConfDownstreamPboControl
            vdslLineConfDownPboControl         INTEGER,
            vdslLineConfUpstreamPboControl
            vdslLineConfUpPboControl           INTEGER,
            vdslLineConfDownstreamPboLevel
            vdslLineConfDownPboLevel           Unsigned32,
            vdslLineConfUpstreamPboLevel
            vdslLineConfUpPboLevel             Unsigned32,
            vdslLineConfDeploymentScenario     INTEGER,
            vdslLineConfAdslPresence           INTEGER,
            vdslLineConfApplicableStandard     INTEGER,
            vdslLineConfBandPlan               INTEGER,
            vdslLineConfBandPlanFx             Unsigned32,
            vdslLineConfBandU0Usage
            vdslLineConfBandOptUsage           INTEGER,
            vdslLineConfUpstreamPsdTemplate
            vdslLineConfUpPsdTemplate          INTEGER,
            vdslLineConfDownstreamPsdTemplate
            vdslLineConfDownPsdTemplate        INTEGER,
            vdslLineConfHamBandMask            BITS,
            vdslLineConfCustomNotch1Start      Unsigned32,
            vdslLineConfCustomNotch1Stop       Unsigned32,
            vdslLineConfCustomNotch2Start      Unsigned32,
            vdslLineConfCustomNotch2Stop       Unsigned32,
            vdslLineConfDownstreamTargetSlowBurstProtection
            vdslLineConfDownTargetSlowBurst    Unsigned32,
            vdslLineConfUpstreamTargetSlowBurstProtection
            vdslLineConfUpTargetSlowBurst      Unsigned32,
            vdslLineConfDownstreamMaxFastFecOverhead
            vdslLineConfDownMaxFastFec         Unsigned32,
            vdslLineConfUpstreamMaxFastFecOverhead
            vdslLineConfUpMaxFastFec           Unsigned32,
            vdslLineConfProfileRowStatus
            vdslLineConfLineType               INTEGER,
            vdslLineConfProfRowStatus          RowStatus
            }

    vdslLineConfProfileName OBJECT-TYPE
        SYNTAX       SnmpAdminString (SIZE (1..32))
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "This object identifies a row in this table.

            A default profile with an index of 'DEFVAL', will
            always exist and its parameters will be set to vendor
            specific values, unless otherwise specified in this
            document."
        ::= { vdslLineConfProfileEntry 1 }

    vdslLineConfDownstreamRateMode

    vdslLineConfDownRateMode OBJECT-TYPE
        SYNTAX       INTEGER
                     {
                     manual(1),
                     adaptAtInit(2)
                     }
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the rate selection behaviour behavior for the line
            in the downstream direction." direction.

            manual(1)       forces the rate to the configured rate
            adaptAtInit(2)  adapts the line based upon line quality."
        DEFVAL       { adaptAtInit }
        ::= { vdslLineConfProfileEntry 2 }
    vdslLineConfUpstreamRateMode

    vdslLineConfUpRateMode OBJECT-TYPE
        SYNTAX       INTEGER
                     {
                     manual(1),
                     adaptAtInit(2)
                     }
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the rate selection behaviour behavior for the line
            in the upstream direction." direction.

            manual(1)       forces the rate to the configured rate
            adaptAtInit(2)  adapts the line based upon line quality."
        DEFVAL       { adaptAtInit }
        ::= { vdslLineConfProfileEntry 3 }

    vdslLineConfDownstreamMaxPwr

    vdslLineConfDownMaxPwr OBJECT-TYPE
        SYNTAX       Unsigned32 (0..58)
        UNITS        "0.25dBm"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the maximum aggregate downstream power
            level in the range 0..14.5dBm." 0 to 14.5 dBm."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 4 }

    vdslLineConfUpstreamMaxPwr

    vdslLineConfUpMaxPwr OBJECT-TYPE
        SYNTAX       Unsigned32 (0..58)
        UNITS        "0.25dBm"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the maximum aggregate upstream power
            level in the range 0..14.5dBm." 0 to 14.5 dBm."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 5 }

    vdslLineConfDownstreamMaxSnrMgn
    vdslLineConfDownMaxSnrMgn OBJECT-TYPE
        SYNTAX       Unsigned32 (0..127)
        UNITS        "0.25dBm"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the maximum downstream Signal/Noise Margin
            in units of 0.25 dB, for a range of 0..31.75 0 to 31.75 dB."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 6 }

    vdslLineConfDownstreamMinSnrMgn

    vdslLineConfDownMinSnrMgn OBJECT-TYPE
        SYNTAX       Unsigned32 (0..127)
        UNITS        "0.25dBm"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the minimum downstream Signal/Noise Margin
            in units of 0.25 dB, for a range of 0..31.75 0 to 31.75 dB."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 7 }

    vdslLineConfDownstreamTargetSnrMgn

    vdslLineConfDownTargetSnrMgn OBJECT-TYPE
        SYNTAX       Unsigned32 (0..127)
        UNITS        "0.25dBm"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the target downstream Signal/Noise Margin
            in units of 0.25 dB, for a range of 0..31.75 0 to 31.75 dB.
            This is the Noise Margin the modems transceivers must achieve
            with a BER of 10-7 10^-7 or better to successfully complete
            initialization."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 8 }

    vdslLineConfUpstreamMaxSnrMgn

    vdslLineConfUpMaxSnrMgn OBJECT-TYPE
        SYNTAX       Unsigned32 (0..127)
        UNITS        "0.25dBm"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the maximum upstream Signal/Noise Margin
            in units of 0.25 dB, for a range of 0..31.75 0 to 31.75 dB."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 9 }

    vdslLineConfUpstreamMinSnrMgn

    vdslLineConfUpMinSnrMgn OBJECT-TYPE
        SYNTAX       Unsigned32 (0..127)
        UNITS        "0.25dBm"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the minimum upstream Signal/Noise Margin
            in units of 0.25 dB, for a range of 0..31.75 0 to 31.75 dB."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 10 }

    vdslLineConfUpstreamTargetSnrMgn

    vdslLineConfUpTargetSnrMgn OBJECT-TYPE
        SYNTAX       Unsigned32 (0..127)
        UNITS        "0.25dBm"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the target upstream Signal/Noise Margin in
            units of 0.25 dB, for a range of 0..31.75 0 to 31.75 dB.  This
            is the Noise Margin the modems transceivers must achieve with
            a BER of
            10-7 10^-7 or better to successfully complete
            initialization."
        REFERENCE    "T1E1.4/2000-009R3"    --    "T1E1.4/2000-009R3, Part 1, common spec spec"
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 11 }

    vdslLineConfDownstreamFastMaxDataRate

    vdslLineConfDownFastMaxDataRate OBJECT-TYPE
        SYNTAX       Unsigned32
        UNITS        "kbps"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the maximum downstream fast channel
            data rate in steps of 1000 bits/second."
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 12 }

    vdslLineConfDownstreamFastMinDataRate

    vdslLineConfDownFastMinDataRate OBJECT-TYPE
        SYNTAX       Unsigned32
        UNITS        "kbps"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the minimum downstream fast channel
            data rate in steps of 1000 bits/second."
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 13 }

    vdslLineConfDownstreamSlowMaxDataRate

    vdslLineConfDownSlowMaxDataRate OBJECT-TYPE
        SYNTAX       Unsigned32
        UNITS        "kbps"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the maximum downstream slow channel
            data rate in steps of 1000 bits/second." bits/second.

            The maximum aggregate downstream transmit speed
            of the line can be derived from the sum of maximum
            downstream fast and slow channel data rates."
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 14 }

    vdslLineConfDownstreamSlowMinDataRate

    vdslLineConfDownSlowMinDataRate OBJECT-TYPE
        SYNTAX       Unsigned32
        UNITS        "kbps"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the minimum downstream slow channel
            data rate in steps of 1000 bits/second." bits/second.

            The minimum aggregate downstream transmit speed
            of the line can be derived from the sum of minimum
            downstream fast and slow channel data rates."
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 15 }

    vdslLineConfUpstreamFastMaxDataRate

    vdslLineConfUpFastMaxDataRate OBJECT-TYPE
        SYNTAX       Unsigned32
        UNITS        "kbps"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the maximum upstream fast channel
            data rate in steps of 1000 bits/second." bits/second.

            The maximum aggregate upstream transmit speed
            of the line can be derived from the sum of maximum
            upstream fast and slow channel data rates."
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 16 }

    vdslLineConfUpstreamFastMinDataRate

    vdslLineConfUpFastMinDataRate OBJECT-TYPE
        SYNTAX       Unsigned32
        UNITS        "kbps"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the minimum upstream fast channel
            data rate in steps of 1000 bits/second." bits/second.

            The minimum aggregate upstream transmit speed
            of the line can be derived from the sum of minimum
            upstream fast and slow channel data rates."
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 17 }

    vdslLineConfUpstreamSlowMaxDataRate

    vdslLineConfUpSlowMaxDataRate OBJECT-TYPE
        SYNTAX       Unsigned32
        UNITS        "kbps"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the maximum upstream slow channel
            data rate in steps of 1000 bits/second."
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 18 }

    vdslLineConfUpstreamSlowMinDataRate

    vdslLineConfUpSlowMinDataRate OBJECT-TYPE
        SYNTAX       Unsigned32
        UNITS        "kbps"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the minimum upstream slow channel
            data rate in steps of 1000 bits/second."
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 19 }

    vdslLineConfDownstreamRateRatio

    vdslLineConfDownRateRatio OBJECT-TYPE
        SYNTAX       Unsigned32 (0..100)
        UNITS        "percent"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "For dynamic rate adaptation at startup, the allocation
            of data rate in excess of the minimum data rate for each
            channel is controlled by the object.  This object specifies
            the ratio of the allocation of the excess data rate between
            the fast and the slow channels.  This allocation represents
            downstream Fast Channel Allocation / Slow Channel
            Allocation."
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 20 }

    vdslLineConfUpstreamRateRatio

    vdslLineConfUpRateRatio OBJECT-TYPE
        SYNTAX       Unsigned32 (0..100)
        UNITS        "percent"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "For dynamic rate adaptation at startup, the allocation
            of data rate in excess of the minimum data rate for each
            channel is controlled by the object.  This object specifies
            the ratio of the allocation of the excess data rate between
            the fast and the slow channels.  This allocation represents
            upstream Fast Channel Allocation / Slow Allocation/Slow Channel Allocation."
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 21 }

    vdslLineConfDownstreamMaxInterDelay

    vdslLineConfDownMaxInterDelay OBJECT-TYPE
        SYNTAX       Unsigned32 (0..255)
        UNITS        "ms"        "milliseconds"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the maximum interleave delay for the
            downstream slow channel."
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 22 }

    vdslLineConfUpstreamMaxInterDelay

    vdslLineConfUpMaxInterDelay OBJECT-TYPE
        SYNTAX       Unsigned32 (0..255)
        UNITS        "ms"        "milliseconds"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the maximum interleave delay for the
            upstream slow channel."
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 23 }

    vdslLineConfDownstreamPboControl

    vdslLineConfDownPboControl OBJECT-TYPE
        SYNTAX       INTEGER
                     {
                     disabled(1),
                     auto(2),
                     manual(3)
                     }
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Downstream power backoff (PBO) control for this
            line.  For modems transceivers which do not support downstream
            PBO control, this object MUST be fixed at disabled(1)." disabled(1).
            If auto(2) is selected, the transceiver will automatically
            adjust the power backoff.  If manual(3) is selected,
            then the transceiver will use the value from
            vdslLineConfDownPboLevel."
        DEFVAL       { disabled }
        ::= { vdslLineConfProfileEntry 24 }

    vdslLineConfUpstreamPboControl

    vdslLineConfUpPboControl OBJECT-TYPE
        SYNTAX       INTEGER
                     {
                     disabled(1),
                     auto(2),
                     manual(3)
                     }
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Upstream power backoff (PBO) control for this
            line.  For modems transceivers which do not support upstream
            PBO control, this object MUST be fixed at disabled(1)."
        ::= { vdslLineConfProfileEntry 25 }

    vdslLineConfDownstreamPboLevel OBJECT-TYPE
        SYNTAX       Unsigned32 (0..160)
        UNITS        "0.25dB" disabled(1).
            If auto(2) is selected, the transceiver will automatically
            adjust the power backoff.  If manual(3) is selected,
            then the transceiver will use the value from
            vdslLineConfUpPboLevel."
        DEFVAL       { disabled }
        ::= { vdslLineConfProfileEntry 25 }

    vdslLineConfDownPboLevel OBJECT-TYPE
        SYNTAX       Unsigned32 (0..160)
        UNITS        "0.25dB"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the downstream backoff level to be used
            when vdslLineConfDownstreamPboControl vdslLineConfDownPboControl = manual(3)."
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 26 }

    vdslLineConfUpstreamPboLevel

    vdslLineConfUpPboLevel OBJECT-TYPE
        SYNTAX       Unsigned32 (0..160)
        UNITS        "0.25dB"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the upstream backoff level to be used
            when vdslLineConfUpstreamPboControl vdslLineConfUpPboControl = manual(3)."
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 27 }

    vdslLineConfDeploymentScenario OBJECT-TYPE
        SYNTAX       INTEGER
                     {
                     fttCab(1),
                     fttEx(2),
                     other(3)
                     }
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "The VDSL line deployment scenario.  When using
            fttCab(1), the VTU-C is located in a street cabinet.
            When using fttEx(2), the VTU-C is located at the
            central office." office.  Changes to this value will have
            no effect on the transceiver."
        REFERENCE    "DSL Forum TR-057"
        DEFVAL       { fttCab }
        ::= { vdslLineConfProfileEntry 28 }

    vdslLineConfAdslPresence OBJECT-TYPE
        SYNTAX       INTEGER
                     {
                     none(1),
                     adslOverPots(2),
                     adslOverISDN(3)
                     }
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Indicates presence of ADSL service in the associated
            cable bundle/binder." bundle/binder.

            none(1)         indicates no ADSL service in the bundle
            adslOverPots(2) indicates ADSL service over POTS is
                            present in the bundle
            adslOverISDN(3) indicates ADSL service over ISDN is
                            present in the bundle"
        DEFVAL       { none }
        ::= { vdslLineConfProfileEntry 29 }

    vdslLineConfApplicableStandard OBJECT-TYPE
        SYNTAX       INTEGER
                     {
                     ansi(1),
                     etsi(2),
                     itu(3),
                     other(4)
                     }
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "The VDSL standard to be used for the line." line.

             ansi(1)      indicates ANSI standard
             etsi(2)      indicates ETSI standard
             itu(3)       indicates ITU standard
             other(4)     indicates a standard other than the above."
        DEFVAL       { ansi }
        ::= { vdslLineConfProfileEntry 30 }

    vdslLineConfBandPlan OBJECT-TYPE
        SYNTAX       INTEGER
                     {
                     bandPlan997(1),
                     bandPlan998(2),
                     bandPlanFx(3),
                     other(4)
                     }
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "The VDSL band plan to be used for the line.

             bandPlan997(1) is to be used for
                  ITU-T G.993.1 Bandplan-B
                  ETSI Bandplan
                  ANSI Plan 997

             bandPlan998(2) is to be used for
                  ITU-T G.993.1 Bandplan-A
                  ANSI Plan 998

             bandPlanFx(3) is to be used for
                  ITU-T G.993.1 Bandplan-C.

             other(4) is to be used for
                  non-standard bandplans.

             If this object is set to bandPlanFx(3), then the
             object vdslLineConfBandPlanFx MUST also be set."
        DEFVAL       { bandPlan997 }
        ::= { vdslLineConfProfileEntry 31 }

    vdslLineConfBandPlanFx OBJECT-TYPE
        SYNTAX       Unsigned32 (3750..12000)
        UNITS        "kHz"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "The frequency limit between bands D2 and U2 when
            vdslLineConfBandPlan is set to bandPlanFx(3)."
        DEFVAL       { 3750 }
        ::= { vdslLineConfProfileEntry 32 }

    vdslLineConfBandU0Usage

    vdslLineConfBandOptUsage OBJECT-TYPE
        SYNTAX       INTEGER
                     {
                     unused(1),
                     upstream(2),
                     downstream(3)
                     }
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Defines the VDSL link use of the optional frequency
            range [25kHz - 138kHz] (U0)." (Opt).

            unused(1)     indicates Opt is unused
            upstream(2)   indicates Opt usage is for upstream
            downstream(3) indicates Opt usage is for downstream."
        REFERENCE    "ITU-T G.993.1, section 6.1"
        DEFVAL       { unused }
        ::= { vdslLineConfProfileEntry 33 }

    vdslLineConfUpstreamPsdTemplate

    vdslLineConfUpPsdTemplate OBJECT-TYPE
        SYNTAX       INTEGER
                     {
                     templateMask1(1),
                     templateMask2(2)
                     }
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "The upstream PSD template to be used for the line." line.
            Here, templateMask1(1) refers to a notched mask that
            limits the transmitted PSD within the internationally
            standardized HAM (Handheld Amateur Radio) radio bands,
            while templateMask2(2) refers to an unnotched mask.

            The masks themselves depend upon the applicable
            standard being used (vdslLineConfApplicableStandard)."
        REFERENCE    "DSL TR-057"
        DEFVAL       { templateMask1 }
        ::= { vdslLineConfProfileEntry 34 }

    vdslLineConfDownstreamPsdTemplate

    vdslLineConfDownPsdTemplate OBJECT-TYPE
        SYNTAX       INTEGER
                     {
                     templateMask1(1),
                     templateMask2(2)
                     }
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "The downstream PSD template to be used for the line." line.
            Here, templateMask1(1) refers to a notched mask that
            limits the transmitted PSD within the internationally
            standardized HAM (Handheld Amateur Radio) radio bands,
            while templateMask2(2) refers to an unnotched mask.

            The masks themselves depend upon the applicable
            standard being used (vdslLineConfApplicableStandard)."
        REFERENCE    "DSL TR-057"
        DEFVAL       { templateMask1 }
        ::= { vdslLineConfProfileEntry 35 }

    vdslLineConfHamBandMask OBJECT-TYPE
        SYNTAX       BITS
            {
            customNotch1(0),     -- custom (region-specific) notch
            customNotch2(1),     -- custom (region-specific) notch
            amateurBand30m(2),   -- amateur radio band notch
            amateurBand40m(3),   -- amateur radio band notch
            amateurBand80m(4),   -- amateur radio band notch
            amateurBand160m(5)   -- amateur radio band notch
            }
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "The transmit power spectral density mask code. code, used
            to avoid interference with HAM (Handheld Amateur Radio)
            radio bands by introducing power control (notching) in one
            or more of these bands.

            Amateur radio band notching is defined in the VDSL
            spectrum as follows:

            Band  Start Frequency     Stop Frequecy Frequency
            ----  ------------------  --------------------------------
            30m   1810 kHz            2000 kHz
            40m   3500 kHz            3800 kHz (ETSI); 4000 kHz (ANSI)
            80m   7000 kHz            7100 kHz (ETSI); 7300 kHz (ANSI)
            160m  10100 kHz           10150 kHz

            Notching for each standard band can be enabled or disabled
            via the bit mask.

            Two custom notches may be specified.  If either of these
            are enabled via the bit mask, then the following objects
            MUST be specified:

            If customNotch1 is enabled, then both
                vdslLineConfCustomNotch1Start
                vdslLineConfCustomNotch1Stop
            MUST be specified.

            If customNotch2 is enabled, then both
                vdslLineConfCustomNotch2Start
                vdslLineConfCustomNotch2Stop
            MUST be specified."
        REFERENCE    "DSLF TR-057, section 2.6"
        DEFVAL       { { } }
        ::= { vdslLineConfProfileEntry 36 }

    vdslLineConfCustomNotch1Start OBJECT-TYPE
        SYNTAX       Unsigned32
        UNITS        "kHz"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the start frequency of amateur radio custom HAM (Handheld
            Amateur Radio) notch 1." 1.  vdslLineConfCustomNotch1Start MUST
            be less than or equal to vdslLineConfCustomNotch1Stop."
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 37 }

    vdslLineConfCustomNotch1Stop OBJECT-TYPE
        SYNTAX       Unsigned32
        UNITS        "kHz"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the stop frequency of amateur radio custom HAM (Handheld
            Amateur Radio) notch 1." 1.  vdslLineConfCustomNotch1Stop MUST
            be greater than or equal to vdslLineConfCustomNotch1Start."
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 38 }

    vdslLineConfCustomNotch2Start OBJECT-TYPE
        SYNTAX       Unsigned32
        UNITS        "kHz"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the start frequency of amateur radio custom HAM (Handheld
            Amateur Radio) notch 2." 2.  vdslLineConfCustomNotch2Start MUST
            be less than or equal to vdslLineConfCustomNotch2Stop."
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 39 }

    vdslLineConfCustomNotch2Stop OBJECT-TYPE
        SYNTAX       Unsigned32
        UNITS        "kHz"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the stop frequency of amateur radio custom HAM (Handheld
            Amateur Radio) notch 2." 2.  vdslLineConfCustomNotch2Stop MUST
            be greater than or equal to vdslLineConfCustomNotch2Stop."
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 40 }

    vdslLineConfDownstreamTargetSlowBurstProtection

    vdslLineConfDownTargetSlowBurst OBJECT-TYPE
        SYNTAX       Unsigned32 (0..1275)
        UNITS        "microseconds"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the target level of impulse noise (burst)
            protection for an interleaved (slow) channel."
        REFERENCE    "ITU-T G.997.1"          -- G.997.1, section 7.3.2.3 7.3.2.3"
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 41 }

    vdslLineConfUpstreamTargetSlowBurstProtection

    vdslLineConfUpTargetSlowBurst OBJECT-TYPE
        SYNTAX       Unsigned32 (0..1275)
        UNITS        "microseconds"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "Specifies the target level of impulse noise (burst)
            protection for an interleaved (slow) channel."
        REFERENCE    "ITU-T G.997.1"          -- G.997.1, section 7.3.2.3 7.3.2.3"
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 42 }

    vdslLineConfDownstreamMaxFastFecOverhead

    vdslLineConfDownMaxFastFec OBJECT-TYPE
        SYNTAX       Unsigned32 (0..50)
        UNITS        "%"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This parameter provisions the maximum level of Forward
            Error Correction (FEC) redundancy related overhead to
            be maintained for a fast channel."
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 43 }

    vdslLineConfUpstreamMaxFastFecOverhead

    vdslLineConfUpMaxFastFec OBJECT-TYPE
        SYNTAX       Unsigned32 (0..50)
        UNITS        "%"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This parameter provisions the maximum level of Forward
            Error Correction (FEC) redundancy related overhead to
            be maintained for a fast channel."
        ::=
        DEFVAL       { 0 }
        ::= { vdslLineConfProfileEntry 44 }

    vdslLineConfProfileRowStatus

    vdslLineConfLineType OBJECT-TYPE
        SYNTAX       INTEGER
            {
            noChannel(1),         -- no channels exist
            fastOnly(2),          -- only fast channel exists
            interleavedOnly(3),   -- only interleaved channel exists
            fastOrInterleaved(4), -- either fast or interleaved channel
                                  -- exist, but only one at a time
            fastAndInterleaved(5) -- both fast and interleaved channels
                                  -- exist
            }
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This parameter provisions the VDSL physical entity at
            start-up by defining whether and how the line will be
            channelized, i.e. which channel type(s) are supported.

            If the line is to be channelized, the value will be other
            than noChannel(1).

            This configuration can be activated only during start-up.
            Afterwards, the value of vdslLineType coincides with the
            value of vdslLineConfLineType.  Depending on this vlaue,
            the corresponding entries in the ifTable for the
            interleaved and the fast channels are enabled or disabled
            according to the value of their ifOperStatus.

            Defined values are:

            noChannel(1)          -- no channels exist
            fastOnly(2)           -- only the fast channel exists
            interleavedOnly(3)    -- only the interleaved channel exists
            fastOrInterleaved(4)  -- either the fast or the interleaved
                                  -- channel exists, but only one at a
                                  -- time
            fastAndInterleaved(5) -- both fast and interleaved channels
                                  -- exist

            Note that 'slow' and 'interleaved' refer to the same
            channel."
        REFERENCE    "T1E1.4/2000-009R3, Part 1, common spec"
        DEFVAL       { noChannel }
        ::= { vdslLineConfProfileEntry 45 }

    vdslLineConfProfRowStatus OBJECT-TYPE
        SYNTAX       RowStatus
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This object is used to create a new row or modify or
            delete an existing row in this table.

            A profile activated by setting this object to `active'. 'active'.
            When `active' 'active' is set, the system will validate the profile.

            Before a profile can be deleted or taken out of
            service, (by setting this object to `destroy' 'destroy' or
            `outOfService')
            'outOfService') it must be first unreferenced
            from all associated lines."
        ::= { vdslLineConfProfileEntry 45 46 }

    --
    -- Alarm configuration profile table
    --

    vdslLineAlarmConfProfileTable OBJECT-TYPE
        SYNTAX       SEQUENCE OF VdslLineAlarmConfProfileEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "This table contains information on the VDSL line alarm
            configuration.  One entry in this table reflects a profile
            defined by a manager which can be used to configure the
            VDSL line alarm thresholds."
        ::= { vdslMibObjects 20 }

    vdslLineAlarmConfProfileEntry OBJECT-TYPE
        SYNTAX       VdslLineAlarmConfProfileEntry
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "Each entry consists of a list of parameters that
            represents the configuration of a VDSL line alarm
            profile.

            A default profile with an index of 'DEFVAL', will
            always exist and its parameters will be set to vendor
            specific values, unless otherwise specified in this
            document."
        INDEX { vdslLineAlarmConfProfileName }
        ::= { vdslLineAlarmConfProfileTable 1 }

    VdslLineAlarmConfProfileEntry ::=
        SEQUENCE
            {
            vdslLineAlarmConfProfileName       SnmpAdminString,
            vdslThresh15MinLofs                HCPerfIntervalThreshold,
            vdslThresh15MinLoss                HCPerfIntervalThreshold,
            vdslThresh15MinLprs                HCPerfIntervalThreshold,
            vdslThresh15MinLols                HCPerfIntervalThreshold,
            vdslThresh15MinESs                 HCPerfIntervalThreshold,
            vdslThresh15MinSESs                HCPerfIntervalThreshold,
            vdslThresh15MinUASs                HCPerfIntervalThreshold,
            vdslInitFailureNotificationEnable
            vdslInitFailureNotifyEnable        TruthValue,
            vdslLineAlarmConfProfileRowStatus
            vdslLineAlarmConfProfRowStatus     RowStatus
            }

    vdslLineAlarmConfProfileName OBJECT-TYPE
        SYNTAX       SnmpAdminString (SIZE (1..32))
        MAX-ACCESS   not-accessible
        STATUS       current
        DESCRIPTION
            "The name for this profile as specified by a user." an
            adminstrator."
        ::= { vdslLineAlarmConfProfileEntry 1 }

    vdslThresh15MinLofs OBJECT-TYPE
        SYNTAX       HCPerfIntervalThreshold
        UNITS        "seconds"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This object configures the threshold for the number of
             loss of frame seconds (lofs) within any given 15-minute
             performance data collection interval.  If the value of
             loss of frame seconds in a particular 15-minute collection
             interval reaches/exceeds this value, a
             vdslPerfLofsThreshNotification notification will be
             generated.  No more than one notification will be sent
             per interval."
        DEFVAL       { 0 }
        ::= { vdslLineAlarmConfProfileEntry 2 }

    vdslThresh15MinLoss OBJECT-TYPE
        SYNTAX       HCPerfIntervalThreshold
        UNITS        "seconds"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This object configures the threshold for the number of
             loss of signal seconds (loss) within any given 15-minute
             performance data collection interval.  If the value of
             loss of signal seconds in a particular 15-minute
             collection interval reaches/exceeds this value, a
             vdslPerfLossThreshNotification notification will be
             generated.  One notification will be sent per interval
             per endpoint."
        DEFVAL       { 0 }
        ::= { vdslLineAlarmConfProfileEntry 3 }

    vdslThresh15MinLprs OBJECT-TYPE
        SYNTAX       HCPerfIntervalThreshold
        UNITS        "seconds"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This object configures the threshold for the number of
             loss of power seconds (lprs) within any given 15-minute
             performance data collection interval.  If the value of
             loss of power seconds in a particular 15-minute collection
             interval reaches/exceeds this value, a
             vdslPerfLprsThreshNotification notification will be
             generated.  No more than one notification will be sent
             per interval."
        DEFVAL       { 0 }
        ::= { vdslLineAlarmConfProfileEntry 4 }

    vdslThresh15MinLols OBJECT-TYPE
        SYNTAX       HCPerfIntervalThreshold
        UNITS        "seconds"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This object configures the threshold for the number of
             loss of link seconds (lols) within any given 15-minute
             performance data collection interval.  If the value of
             loss of power seconds in a particular 15-minute collection
             interval reaches/exceeds this value, a
             vdslPerfLolsThreshNotification notification will be
             generated.  No more than one notification will be sent
             per interval."
        DEFVAL       { 0 }
        ::= { vdslLineAlarmConfProfileEntry 5 }

    vdslThresh15MinESs OBJECT-TYPE
        SYNTAX       HCPerfIntervalThreshold
        UNITS        "seconds"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This object configures the threshold for the number of
             errored seconds (ESs) within any given 15-minute
             performance data collection interval.  If the value of
             errored seconds in a particular 15-minute collection
             interval reaches/exceeds this value, a
             vdslPerfESsThreshNotification notification will be
             generated.  No more than one notification will be sent
             per interval."
        DEFVAL       { 0 }
        ::= { vdslLineAlarmConfProfileEntry 6 }

    vdslThresh15MinSESs OBJECT-TYPE
        SYNTAX       HCPerfIntervalThreshold
        UNITS        "seconds"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This object configures the threshold for the number of
             severely errored seconds (SESs) within any given 15-minute
             performance data collection interval.  If the value of
             severely errored seconds in a particular 15-minute
             collection interval reaches/exceeds this value, a
             vdslPerfSESsThreshNotification notification will be
             generated.  No more than one notification will be sent
             per interval."
        DEFVAL       { 0 }
        ::= { vdslLineAlarmConfProfileEntry 7 }

    vdslThresh15MinUASs OBJECT-TYPE
        SYNTAX       HCPerfIntervalThreshold
        UNITS        "seconds"
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This object configures the threshold for the number of
             unavailable seconds (UASs) within any given 15-minute
             performance data collection interval.  If the value of
             unavailable seconds in a particular 15-minute collection
             interval reaches/exceeds this value, a
             vdslPerfUASsThreshNotification notification will be
             generated.  No more than one notification will be sent
             per interval."
        DEFVAL       { 0 }
        ::= { vdslLineAlarmConfProfileEntry 8 }

    vdslInitFailureNotificationEnable

    vdslInitFailureNotifyEnable OBJECT-TYPE
        SYNTAX       TruthValue
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This object specifies if a vdslInitFailureNotification
            notification will be generated if an initialization
            failure occurs."
        DEFVAL       { false }
        ::= { vdslLineAlarmConfProfileEntry 9 }

    vdslLineAlarmConfProfileRowStatus

    vdslLineAlarmConfProfRowStatus OBJECT-TYPE
        SYNTAX       RowStatus
        MAX-ACCESS   read-create
        STATUS       current
        DESCRIPTION
            "This object is used to create a new row or modify or
            delete an existing row in this table.

            A profile activated by setting this object to `active'. 'active'.
            When `active' 'active' is set, the system will validate the profile.

            Before a profile can be deleted or taken out of service,
            (by setting this object to `destroy' 'destroy' or `outOfService') 'outOfService') it
            must be first unreferenced from all associated lines."
        ::= { vdslLineAlarmConfProfileEntry 10 }

    -- Notification definitions

    vdslNotifications OBJECT IDENTIFIER ::= { vdslLineMib 0 }

    vdslPerfLofsThreshNotification NOTIFICATION-TYPE
        OBJECTS      {
                     vdslPerfCurr15MinLofs,
                     vdslThresh15MinLofs
                     vdslPerfCurr15MinLofs
                     }
        STATUS       current
        DESCRIPTION
            "Loss of Framing 15-minute interval threshold
             (vdslThresh15MinLofs) reached."
        ::= { vdslNotifications 1 }

    vdslPerfLossThreshNotification NOTIFICATION-TYPE
        OBJECTS       {
                      vdslPerfCurr15MinLoss,
                      vdslThresh15MinLoss
                      vdslPerfCurr15MinLoss
                      }
        STATUS        current
        DESCRIPTION
            "Loss of Signal 15-minute interval threshold
            (vdslThresh15MinLoss) reached."
        ::= { vdslNotifications 2 }

    vdslPerfLprsThreshNotification NOTIFICATION-TYPE
        OBJECTS       {
                      vdslPerfCurr15MinLprs,
                      vdslThresh15MinLprs
                      vdslPerfCurr15MinLprs
                      }
        STATUS        current
        DESCRIPTION
            "Loss of Power 15-minute interval threshold
            (vdslThresh15MinLprs) reached."
        ::= { vdslNotifications 3 }

    vdslPerfLolsThreshNotification NOTIFICATION-TYPE
        OBJECTS       {
                      vdslPerfCurr15MinLols,
                      vdslThresh15MinLols
                      vdslPerfCurr15MinLols
                      }
        STATUS        current
        DESCRIPTION
            "Loss of Link 15-minute interval threshold
            (vdslThresh15MinLols) reached."
        ::= { vdslNotifications 4 }

    vdslPerfESsThreshNotification NOTIFICATION-TYPE
        OBJECTS       {
                      vdslPerfCurr15MinESs,
                      vdslThresh15MinESs
                      vdslPerfCurr15MinESs
                      }
        STATUS        current
        DESCRIPTION
            "Errored Seconds 15-minute interval threshold
            (vdslThresh15MinESs) reached."
        ::= { vdslNotifications 5 }

    vdslPerfSESsThreshNotification NOTIFICATION-TYPE
        OBJECTS       {
                      vdslPerfCurr15MinSESs,
                      vdslThresh15MinSESs
                      vdslPerfCurr15MinSESs
                      }
        STATUS        current
        DESCRIPTION
            "Severely Errored Seconds 15-minute interval threshold
            (vdslThresh15MinSESs) reached."
        ::= { vdslNotifications 6 }

    vdslPerfUASsThreshNotification NOTIFICATION-TYPE
        OBJECTS       {
                      vdslPerfCurr15MinUASs,
                      vdslThresh15MinUASs
                      vdslPerfCurr15MinUASs
                      }
        STATUS        current
        DESCRIPTION
            "Unavailable Seconds 15-minute interval threshold
            (vdslThresh15MinUASs) reached."
        ::= { vdslNotifications 7 }

    vdslDownMaxSnrMgnExceededNotification

    vdslDownMaxSnrMgnNotification NOTIFICATION-TYPE
        OBJECTS       {
                      vdslCurrSnrMgn,
                      vdslLineConfDownstreamMaxSnrMgn
                      vdslCurrSnrMgn
                      }
        STATUS        current
        DESCRIPTION
            "The downstream Signal to Noise Margin exceeded
            vdslLineConfDownstreamMaxSnrMgn.
            vdslLineConfDownMaxSnrMgn.  The object
            vdslCurrSnrMgn will contain the Signal to Noise
            margin as measured by the VTU-R."
        ::= { vdslNotifications 8 }

    vdslDownMinSnrMgnExceededNotification

    vdslDownMinSnrMgnNotification NOTIFICATION-TYPE
        OBJECTS       {
                      vdslCurrSnrMgn,
                      vdslLineConfDownstreamMinSnrMgn
                      vdslCurrSnrMgn
                      }
        STATUS        current
        DESCRIPTION
            "The downstream Signal to Noise Margin fell below
            vdslLineConfDownstreamMinSnrMgn.
            vdslLineConfDownMinSnrMgn.    The object
            vdslCurrSnrMgn will contain the Signal to Noise
            margin as measured by the VTU-R."
        ::= { vdslNotifications 9 }

    vdslUpMaxSnrMgnExceededNotification

    vdslUpMaxSnrMgnNotification NOTIFICATION-TYPE
        OBJECTS       {
                      vdslCurrSnrMgn,
                      vdslLineConfUpstreamMaxSnrMgn
                      vdslCurrSnrMgn
                      }
        STATUS        current
        DESCRIPTION
            "The upstream Signal to Noise Margin exceeded
            vdslLineConfDownstreamMaxSnrMgn.
            vdslLineConfUpMaxSnrMgn.    The object
            vdslCurrSnrMgn will contain the Signal to Noise
            margin as measured by the VTU-C."
        ::= { vdslNotifications 10 }

    vdslUpMinSnrMgnExceededNotification

    vdslUpMinSnrMgnNotification NOTIFICATION-TYPE
        OBJECTS       {
                      vdslCurrSnrMgn,
                      vdslLineConfUpstreamMinSnrMgn
                      vdslCurrSnrMgn
                      }
        STATUS        current
        DESCRIPTION
            "The upstream Signal to Noise Margin fell below
            vdslLineConfDownstreamMinSnrMgn.
            vdslLineConfUpMinSnrMgn.    The object
            vdslCurrSnrMgn will contain the Signal to Noise
            margin as measured by the VTU-C."
        ::= { vdslNotifications 11 }

    vdslInitFailureNotification NOTIFICATION-TYPE
        OBJECTS       {
                      vdslCurrStatus
                      }
        STATUS        current
        DESCRIPTION
            "Vtu initialization failed.  See vdslCurrStatus for
            potential reasons."
        ::= { vdslNotifications 12 }

    -- conformance information

    vdslConformance OBJECT IDENTIFIER ::= { vdslLineMib 3 }
    vdslGroups OBJECT IDENTIFIER ::= { vdslConformance 1 }
    vdslCompliances OBJECT IDENTIFIER ::= { vdslConformance 2 }

    vdslLineMibCompliance MODULE-COMPLIANCE
        STATUS  current
        DESCRIPTION
            "The compliance statement for SNMP entities which
            manage VDSL interfaces."

        MODULE  -- this module
        MANDATORY-GROUPS
            {
            vdslGroup
            vdslGroup,
            vdslNotificationGroup
            }
        ::= { vdslCompliances 1 }

    -- units of conformance

        vdslGroup OBJECT-GROUP
            OBJECTS
                {
                vdslLineCoding,
                vdslLineType,
                vdslLineConfProfile,
                vdslLineAlarmConfProfile,
                vdslInvSerialNumber,
                vdslInvVendorID,
                vdslInvVersionNumber,
                vdslCurrSnrMgn,
                vdslCurrAtn,
                vdslCurrStatus,
                vdslCurrOutputPwr,
                vdslCurrAttainableRate,
                vdslCurrLineRate,
                vdslChanInterleaveDelay,
                vdslChanCrcBlockLength,
                vdslChanCurrTxRate,
                vdslChanCurrTxSlowBurstProtection,
                vdslChanCurrTxFastFecOverhead,
                vdslChanCurrTxSlowBurstProtect,
                vdslChanCurrTxFastFec,
                vdslPerfValidIntervals,
                vdslPerfInvalidIntervals,
                vdslPerfLofs,
                vdslPerfLoss,
                vdslPerfLprs,
                vdslPerfLols,
                vdslPerfESs,
                vdslPerfSESs,
                vdslPerfUASs,
                vdslPerfInits,
                vdslPerfCurr15MinTimeElapsed,
                vdslPerfCurr15MinLofs,
                vdslPerfCurr15MinLoss,
                vdslPerfCurr15MinLprs,
                vdslPerfCurr15MinLols,
                vdslPerfCurr15MinESs,
                vdslPerfCurr15MinSESs,
                vdslPerfCurr15MinUASs,
                vdslPerfCurr15MinInits,
                vdslPerf1DayValidIntervals,
                vdslPerf1DayInvalidIntervals,
                vdslPerfCurr1DayTimeElapsed,
                vdslPerfCurr1DayLofs,
                vdslPerfCurr1DayLoss,
                vdslPerfCurr1DayLprs,
                vdslPerfCurr1DayLols,
                vdslPerfCurr1DayESs,
                vdslPerfCurr1DaySESs,
                vdslPerfCurr1DayUASs,
                vdslPerfCurr1DayInits,
                vdslIntervalLofs,
                vdslIntervalLoss,
                vdslIntervalLprs,
                vdslIntervalLols,
                vdslIntervalESs,
                vdslIntervalSESs,
                vdslIntervalUASs,
                vdslIntervalInits,
                vdsl1DayIntervalMoniSecs,
                vdsl1DayIntervalLofs,
                vdsl1DayIntervalLoss,
                vdsl1DayIntervalLprs,
                vdsl1DayIntervalLols,
                vdsl1DayIntervalESs,
                vdsl1DayIntervalSESs,
                vdsl1DayIntervalUASs,
                vdsl1DayIntervalInits,
                vdslChanPerfValidIntervals,
                vdslChanPerfInvalidIntervals,
                vdslChanCorrectedOctets,
                vdslChanUncorrectableBlks,
                vdslChanPerfCurr15MinTimeElapsed,
                vdslChanPerfCurr15MinCorrectedOctets,
                vdslChanPerfCurr15MinUncorrectableBlks,
                vdslChanPerf1DayValidIntervals,
                vdslChanPerf1DayInvalidIntervals,
                vdslChanPerfCurr1DayTimeElapsed,
                vdslChanPerfCurr1DayCorrectedOctets,
                vdslChanPerfCurr1DayUncorrectableBlks,
                vdslChanIntervalCorrectedOctets,
                vdslChanIntervalUncorrectableBlks,
                vdslChanValidIntervals,
                vdslChanInvalidIntervals,
                vdslChanFixedOctets,
                vdslChanBadBlks,
                vdslChanCurr15MinTimeElapsed,
                vdslChanCurr15MinFixedOctets,
                vdslChanCurr15MinBadBlks,
                vdslChan1DayValidIntervals,
                vdslChan1DayInvalidIntervals,
                vdslChanCurr1DayTimeElapsed,
                vdslChanCurr1DayFixedOctets,
                vdslChanCurr1DayBadBlks,
                vdslChanIntervalFixedOctets,
                vdslChanIntervalBadBlks,
                vdslChan1DayIntervalMoniSecs,
                vdslChan1DayIntervalCorrectedOctets,
                vdslChan1DayIntervalUncorrectableBlks,
                vdslLineConfDownstreamRateMode,
                vdslLineConfUpstreamRateMode,
                vdslLineConfDownstreamMaxPwr,
                vdslLineConfUpstreamMaxPwr,
                vdslLineConfDownstreamMaxSnrMgn,
                vdslLineConfDownstreamMinSnrMgn,
                vdslLineConfDownstreamTargetSnrMgn,
                vdslLineConfUpstreamMaxSnrMgn,
                vdslLineConfUpstreamMinSnrMgn,
                vdslLineConfUpstreamTargetSnrMgn,
                vdslLineConfDownstreamFastMaxDataRate,
                vdslLineConfDownstreamFastMinDataRate,
                vdslLineConfDownstreamSlowMaxDataRate,
                vdslLineConfDownstreamSlowMinDataRate,
                vdslLineConfUpstreamFastMaxDataRate,
                vdslLineConfUpstreamFastMinDataRate,
                vdslLineConfUpstreamSlowMaxDataRate,
                vdslLineConfUpstreamSlowMinDataRate,
                vdslLineConfDownstreamRateRatio,
                vdslLineConfUpstreamRateRatio,
                vdslLineConfDownstreamMaxInterDelay,
                vdslLineConfUpstreamMaxInterDelay,
                vdslLineConfDownstreamPboControl,
                vdslLineConfUpstreamPboControl,
                vdslLineConfDownstreamPboLevel,
                vdslLineConfUpstreamPboLevel,
                vdslChan1DayIntervalFixedOctets,
                vdslChan1DayIntervalBadBlks,
                vdslLineConfDownRateMode,
                vdslLineConfUpRateMode,
                vdslLineConfDownMaxPwr,
                vdslLineConfUpMaxPwr,
                vdslLineConfDownMaxSnrMgn,
                vdslLineConfDownMinSnrMgn,
                vdslLineConfDownTargetSnrMgn,
                vdslLineConfUpMaxSnrMgn,
                vdslLineConfUpMinSnrMgn,
                vdslLineConfUpTargetSnrMgn,
                vdslLineConfDownFastMaxDataRate,
                vdslLineConfDownFastMinDataRate,
                vdslLineConfDownSlowMaxDataRate,
                vdslLineConfDownSlowMinDataRate,
                vdslLineConfUpFastMaxDataRate,
                vdslLineConfUpFastMinDataRate,
                vdslLineConfUpSlowMaxDataRate,
                vdslLineConfUpSlowMinDataRate,
                vdslLineConfDownRateRatio,
                vdslLineConfUpRateRatio,
                vdslLineConfDownMaxInterDelay,
                vdslLineConfUpMaxInterDelay,
                vdslLineConfDownPboControl,
                vdslLineConfUpPboControl,
                vdslLineConfDownPboLevel,
                vdslLineConfUpPboLevel,
                vdslLineConfDeploymentScenario,
                vdslLineConfAdslPresence,
                vdslLineConfApplicableStandard,
                vdslLineConfBandPlan,
                vdslLineConfBandPlanFx,
                vdslLineConfBandU0Usage,
                vdslLineConfUpstreamPsdTemplate,
                vdslLineConfDownstreamPsdTemplate,
                vdslLineConfBandOptUsage,
                vdslLineConfUpPsdTemplate,
                vdslLineConfDownPsdTemplate,
                vdslLineConfHamBandMask,
                vdslLineConfCustomNotch1Start,
                vdslLineConfCustomNotch1Stop,
                vdslLineConfCustomNotch2Start,
                vdslLineConfCustomNotch2Stop,
                vdslLineConfDownstreamTargetSlowBurstProtection,
                vdslLineConfUpstreamTargetSlowBurstProtection,
                vdslLineConfDownstreamMaxFastFecOverhead,
                vdslLineConfUpstreamMaxFastFecOverhead,
                vdslLineConfProfileRowStatus,
                vdslLineConfDownTargetSlowBurst,
                vdslLineConfUpTargetSlowBurst,
                vdslLineConfDownMaxFastFec,
                vdslLineConfUpMaxFastFec,
                vdslLineConfLineType,
                vdslLineConfProfRowStatus,
                vdslThresh15MinLofs,
                vdslThresh15MinLoss,
                vdslThresh15MinLprs,
                vdslThresh15MinLols,
                vdslThresh15MinESs,
                vdslThresh15MinSESs,
                vdslThresh15MinUASs,
                vdslInitFailureNotificationEnable,
                vdslLineAlarmConfProfileRowStatus
                vdslInitFailureNotifyEnable,
                vdslLineAlarmConfProfRowStatus
                }
            STATUS     current
            DESCRIPTION
                "A collection of objects providing information about
                 a VDSL Line."
            ::= { vdslGroups 1 }

        vdslNotificationGroup    NOTIFICATION-GROUP
            NOTIFICATIONS
                {
                vdslPerfLofsThreshNotification,
                vdslPerfLossThreshNotification,
                vdslPerfLprsThreshNotification,
                vdslPerfLolsThreshNotification,
                vdslPerfESsThreshNotification,
                vdslPerfSESsThreshNotification,
                vdslPerfUASsThreshNotification,
                vdslDownMaxSnrMgnExceededNotification,
                vdslDownMinSnrMgnExceededNotification,
                vdslUpMaxSnrMgnExceededNotification,
                vdslUpMinSnrMgnExceededNotification,
                vdslDownMaxSnrMgnNotification,
                vdslDownMinSnrMgnNotification,
                vdslUpMaxSnrMgnNotification,
                vdslUpMinSnrMgnNotification,
                vdslInitFailureNotification
                }
            STATUS      current
            DESCRIPTION
                 "This group supports notifications of significant
                 conditions associated with VDSL Lines."
        ::= { vdslGroups 2 }

    END

Normative References

   [ETSI2701] ETSI TS 101 270-1 V1.2.1 "Transmission and Multiplexing
              (TM); Access transmission

5.  Intellectual Property Notice

   The IETF takes no position regarding the validity or scope of any
   intellectual property or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available;  neither does it represent that it
   has made any effort to identify any such rights.  Information on the
   IETF's procedures with respect to rights in standards-track and
   standards-related documentation can be found in BCP-11.  Copies of
   claims of rights made available for publication and any assurances
   of licenses to be made available, or the result of an attempt made
   to obtain a general license or permission for the use of such
   proprietary rights by implementors or users of this specification
   can be obtained from the IETF Secretariat.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights which may cover technology that may be required to practice
   this standard.  Please address the information to the IETF Executive
   Director.

6.  Normative References

   [DSLFTR057] DSL Forum TR-057, "VDSL Network Element Management",
              February 2003.

   [ETSI2701] ETSI TS 101 270-1 V1.2.1 "Transmission and Multiplexing
              (TM); Access transmission systems on metallic access
              cables; Very high speed Digital Subscriber Line (VDSL);
              Part 1: Functional requirements", October 1999.

   [ETSI2702] ETSI TS 101 270-2 V1.1.1 "Transmission and Multiplexing
              (TM); Access transmission systems on metallic access
              cables; Very high speed Digital Subscriber Line (VDSL);
              Part 1: Transceiver specification", February 2001.

   [ITU9931]  ITU-T G.993.1 "Very-high-speed digital subscriber line
              foundation", November 2001.

   [ITU9971]  ITU-T G.997.1 "Physical layer management for Digital
              Subscriber Line (DSL) Transcievers", Transceivers", July 1999.

   [RFC1901]  Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
              "Introduction to Community-based SNMPv2", RFC 1901,
              January 1996.

   [RFC1905]  Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
              "Protocol Operations for Version 2 of the Simple Network
              Management Protocol (SNMPv2)", RFC 1905, January 1996.

   [RFC1906]  Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
              "Transport Mappings for Version 2 of the Simple Network
              Management Protocol (SNMPv2)", RFC 1906, January 1996.

   [RFC2119]  Bradner, S., "Key Words for use in RFCs to Indicate
              Requirement Levels", RFC 2119, March 1997.

   [RFC2493]  Tesink, K., "Textual Conventions for MIB Modules Using
              Performance History Based on 15 Minute Intervals", RFC
              2493, January 1999.

   [RFC2571]  Harrington, D., Presuhn, R. and B. Wijnen, "An
              Architecture for Describing SNMP Management Frameworks",
              RFC 2571, April 1999.

   [RFC2572]  Case, J., Harrington D., Presuhn, R. and B. Wijnen,
              "Message Processing and Dispatching for the Simple Network
              Management Protocol (SNMP)", RFC 2572, April 1999.

   [RFC2574]  Blumenthal, U. and B. Wijnen, "User-based Security Model
              (USM) for version 3 of the Simple Network Management
              Protocol (SNMPv3)", RFC 2574, April 1999.

   [RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
             Rose, M.  and S.  Waldbusser, "Structure of Management
             Information Version 2 (SMIv2)", STD 58, RFC 2578, April
             1999.

   [RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
             Rose, M.  and S.  Waldbusser, "Textual Conventions for
             SMIv2", STD 58, RFC 2579, April 1999.

   [RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
             Rose, M.  and S.  Waldbusser, "Conformance Statements for
             SMIv2", STD 58, RFC 2580, April 1999.

   [RFC2662]  Bathrick, G. and F. Ly, "Definitions of Managed Objects
              for the ADSL Lines",  RFC 2662, August 1999.

   [RFC2863] McCloghrie, K.  and F.  Kastenholz, "The Interfaces Group
             MIB", RFC 2863, June 2000.

   [RFC3418] Presuhn, R., "Management Information Base (MIB) for the
             Simple Network Management Protocol (SNMP)", STD 62, RFC
             3418, December 2002.

   [RFCXXXX] Ray, B. and R. Abbi, "High Capacity Textual Conventions
             for MIB Modules Using Performance History Based on
             15 Minute Intervals", RFC XXXX, YYYY 2003.
--- RFC Ed: please replace XXXX with the RFC number assigned to the
--- accompanying HC-TC MIB and YYYY with the appropriate month.

   [T1E1311] ANSI T1E1.4/2001-311, "Very-high-bit-rate Digital
             Subscriber Line (VDSL) Metallic Interface, Part 1:
             Functional Requirements and Common Specification",
             February 2001.

   [T1E1011] ANSI T1E1.4/2001-011R3, "VDSL Metallic Interface, Part 2:
             Technical Specification for a Single-Carrier Modulation
             (SCM) Transceiver", November 2001.

   [T1E1013] ANSI T1E1.4/2001-013R4, "VDSL Metallic Interface, Part 3:
             Technical Specification for a Multi-Carrier Modulation
             (MCM) Transceiver", November 2000.

7.  Informative References

   [RFC1155]  Rose, M. and K. McCloghrie, "Structure and Identification
              of Management Information for TCP/IP-based Internets", STD
              16, RFC 1155, May 1990.

   [RFC1157]  Case, J., Fedor, M., Schoffstall, M. and J. Davin, "Simple
              Network Management Protocol", STD 15, RFC 1157, May 1990.

   [RFC1212]  Rose, M. and K. McCloghrie, "Concise MIB Definitions", STD
              16, RFC 1212, March 1991.

   [RFC1215]  Rose, M., "A Convention for Defining Traps for use with
              the SNMP", RFC 1215, March 1991.

   [RFC2570]  Case, J., Mundy, R., Partain, D. and B. Stewart,
              "Introduction to Version 3 of the Internet-standard
              Network Management Framework", RFC 2570, April 1999.

   [RFC2573]  Levi, D., Meyer, P. and B. Stewart, "SNMPv3 Applications",
              RFC 2573, April 1999.

   [RFC2575] Wijnen, B., Presuhn, R.  and K.  McCloghrie, "View-based
             Access Control Model (VACM) for the Simple Network
             Management Protocol (SNMP)", RFC 2575, April 1999.

   [RFC3410] Case, J., Mundy, R., Partain, D.  and B.  Stewart,
             "Introduction and Applicability Statements for Internet-
             Standard Management Framework", RFC 3410, December 2002.

8.  Security Considerations

   There are a number of management objects defined in this MIB that
   have a MAX-ACCESS clause of read-write and/or read-create.  Such
   objects may be considered sensitive or vulnerable in some network
   environments.  The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on
   network operations.

   VDSL layer connectivity from the Vtur will permit the subscriber
   to manipulate both the VDSL link directly and the VDSL embedded
   operations channel (EOC) for their own loop.  For example, unchecked
   or unfiltered fluctuations initiated by the subscriber could
   generate sufficient notifications to potentially overwhelm either
   the management interface to the network or the element manager.

   For this reason, there are a number of managed objects in this MIB
   that may contain sensitive information.  These are:

        vdslThresh15MinLofs
        vdslThresh15MinLoss
        vdslThresh15MinLprs
        vdslThresh15MinLols
        vdslThresh15MinESs
        vdslThresh15MinSESs
        vdslThresh15MinUASs

   It is thus important to control even GET access to these objects and
   possibly to even encrypt the values of these objects when sending
   them over the network via SNMP.  Not all versions of SNMP provide
   features for such a secure environment.

   Further, notifications generated by agents implementing this MIB
   will contain the above threshold information.

   SNMPv1 by itself is

   SNMP versions prior to SNMPv3 did not a secure environment. include adequate security.
   Even if the network itself is secure (for example by using IPSec),
   even then, there is no control as to who on the secure network is
   allowed to access and GET/SET (read/change/create/delete) the objects
   which utilize the textual conventions defined in this MIB. MIB module.

   It is recommended RECOMMENDED that the implementers consider the security features
   as provided by the SNMPv3 framework.  Specifically, the use
   of framework (see [RFC3410], section 8),
   including full support for the User-based Security Model RFC 2574 [12] SNMPv3 cryptographic mechanisms (for
   authentication and the View-
   based Access Control Model RFC 2575 [15] privacy).

   Further, deployment of SNMP versions prior to SNMPv3 is NOT
   RECOMMENDED.  Instead, it is recommended. RECOMMENDED to deploy SNMPv3 and to
   enable cryptographic security.  It is then a customer/user customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of a MIB module which utilizes the textual conventions
   defined in this MIB, MIB module is properly configured to give access to
   the objects only to those principals (users) that have legitimate
   rights to indeed GET or SET (change/create/delete) them.

IANA Considerations

   The VDSL-LINE-MIB MIB module requires the allocation of a single
   object identifier for its MODULE-IDENTITY.  IANA should allocate
   this object identifier in the transmission subtree.

9.  Acknowledgments

   Greg Bathrick (Nokia)

   Umberto Bonollo (NEC)

   Andrew Cheers (NEC)
   Felix Flemisch (Siemens)

   David Horton (CiTR)

   Travis Levin (Paradyne)

   Moti Morgenstern (Inovia)

   Randy Presuhn (BMC)

   Say Sabit (NLC)

   Bert Wijnen (Lucent)

Intellectual Property Notice

   The IETF takes no position regarding the validity or scope of any
   intellectual property or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; neither does it represent that it
   has made any effort to identify any such rights.  Information on the
   IETF's procedures with respect to rights in standards-track and
   standards-related documentation can be found in BCP-11.  Copies of
   claims of rights made available for publication and any assurances of
   licenses to be made available, or the result of an attempt made to
   obtain a general license or permission for the use of such
   proprietary rights by implementors or users of this specification can
   be obtained from the IETF Secretariat.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights which may cover technology that may be required to practice
   this standard.  Please address the information to the IETF Executive
   Director.

10.  Authors' Addresses

   Bob Ray
   PESA Switching Systems, Inc.
   330-A Wynn Drive
   Huntsville, AL 35805
   USA

   Phone: +1 256 726 9200 ext.  142
   Fax: +1 256 726 9271
   EMail: rray@pesa.com

   Rajesh Abbi
   Alcatel USA
   2912 Wake Forest Road
   Raleigh, NC 27609-7860
   USA

   Phone: +1 919 850 6194
   EMail: Rajesh.Abbi@alcatel.com

11.  Full Copyright Statement

   Copyright (C) The Internet Society (2003).  All Rights Reserved.
   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph
   are included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.