IPCDN
   Internet Draft                                        Gordon Beacham
   Document: draft-ietf-ipcdn-pktc-signaling-             Motorola, Inc
   02.txt
   03.txt
                                                           Satish Kumar
                                                      Texas Instruments
                                                                Sumanth
                                                          Channabasappa
                                                         Alopa Networks
                                                                    Inc
   Expires: April July 2004                                     October 2003

     Network Control                                     February 2004

   Network-Based Call Signaling (NCS) Signaling MIB for PacketCable and
              IPCablecom Multimedia Terminal Adapters (MTAs)

Status of this Memo

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six
   months and may be updated, replaced, or obsoleted by other documents
   at any time.  It is inappropriate to use Internet-Drafts as
   reference material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
        http://www.ietf.org/ietf/1id-abstracts.txt
   The list of Internet-Draft Shadow Directories can be accessed at
        http://www.ietf.org/shadow.html.

Copyright Notice

   Copyright (C) The Internet Society (2003). (2004). All Rights Reserved.

Abstract

   This memo defines a portion of the Management Information Base (MIB)
   for use with network management protocols in the Internet community.
   In particular, it provides a common data and format representation
   for PacketCable and IPCablecom compliant Multimedia Terminal Adapter
   devices.

   This memo specifies a MIB module in a manner that is compliant to
   the SNMP SMIv2.  The set of objects are consistent with the SNMP
   framework and existing SNMP standards.

PacketCable/IPCablecom NCS Signaling MIB                  October 2003                 February 2004

Table of Contents

   1. The Internet-Standard Management Framework....................2
   2. Terminology...................................................2
      2.1 MTA.......................................................2 MTA.......................................................3
      2.2 Endpoint..................................................3
      2.3 L Line Package............................................3
      2.4 E Line Package............................................3
   3. Overview......................................................3
      3.1 Structure of the MIB......................................3 MIB......................................4
      3.2 pktcSigDevConfigObjects...................................4
      3.3 pktcSigNotification.......................................6
      3.4 pktcSigConformance........................................6
   4. Definitions...................................................6 Definitions...................................................7
   5. Acknowledgments..............................................52 Acknowledgments..............................................54
   6. Normative References.........................................52 References.........................................55
   7. Informative References.......................................53 References.......................................55
   8. Security Considerations......................................54 Considerations......................................57
   9. Intellectual Property........................................56 Property........................................58
   10. Authors' Addresses..........................................56 Addresses..........................................59
   11. Full Copyright Statement....................................57 Statement....................................59

1. The Internet-Standard Management Framework

   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to section 7 of
   RFC 3410 [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB. MIB objects are generally
   accessed through the Simple Network Management Protocol (SNMP).
   Objects in the MIB are defined using the mechanisms defined in the
   Structure of Management Information (SMI). This memo specifies a MIB
   module that is compliant to the SMIv2, which is described in STD 58,
   RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
   [RFC2580].

2. Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL", when used in the guidelines in this memo, are to be
   interpreted as described in RFC 2119 [RFC2119].

   The terms "MIB module" and "information module" are used
   interchangeably in this memo.  As used here, both terms refer to any
   of the three types of information modules defined in Section 3 of
   RFC 2578 [RFC2578].

2.1 MTA

PacketCable/IPCablecom NCS Signaling MIB                  October 2003                 February 2004

2.1 MTA

   A Multimedia Terminal Adapter is a PacketCable or IPCablecom
   compliant device providing telephony services over a cable or hybrid
   system used to deliver video signals to a community. It contains an
   interface to endpoints, a network interface, CODECs, and all
   signaling and encapsulation functions required for Voice over IP
   transport, call signaling, and Quality of Service signaling. A MTA
   can be an embedded or a standalone device. An Embedded MTA (E-MTA)
   is a MTA device containing an embedded DOCSIS Cable Modem. A
   Standalone MTA (S-MTA) is a MTA device separated from the DOCSIS
   Cable Modem by non-DOCSIS MAC interface (e.g., Ethernet, USB).

2.2 Endpoint

   An endpoint or MTA endpoint is a standard RJ-11 telephony physical
   port located on the MTA and used for attaching the telephone device
   to the MTA.

2.3 L Line Package

   The L line package refers to the core signaling functionality as
   defined by PacketCable and IPCablecom. An MTA provides all L package
   elements, however the operator determines their application.

2.4 E Line Package

   The E line package refers to extensions, over and above the core L
   package, defined in support of international requirements. E line
   package elements are optional, vary from country to country, and are
   set by operator or regulatory requirements.

3. Overview

   This MIB provides a set of objects required for Signaling
   PacketCable and IPCablecom compliant Multimedia Terminal Adapter
   (MTA) devices. MTA devices include one or more endpoints (e.g.,
   telephone ports) which receive signaling information to establish
   ring cadence, and codecs used for providing telephony service.

   Telephone systems are typically very complex and often have a wide
   distribution. It is therefore important for management systems to
   support MTAs from multiple vendors at the same time, including those
   from multiple countries. This MIB module provides objects suitable
   for managing signaling for MTA devices in the widest possible
   variety of marketplaces.

   Several normative and informative references are used to help define
   NCS Signaling MIB objects. As a convention, in the object REFERENCE

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

   clauses, we use the PacketCable reference. IPCablecom compliant MTA
   devices MUST use the equivalent IPCablecom references.

3.1 Structure of the MIB

   This MIB is identified by pktcSigMib and is structured in three
   groups:

   - Signaling information that control device and endpoint
   configuration objects (pktcSigMibObjects)

   - Signaling Notification object, that notifies the status
   (pktcSigNotification)

PacketCable/IPCablecom NCS Signaling MIB                  October 2003

   - Signaling Conformance has mandatory signaling objects
   (pktcSigConformance)

   Each group of objects is explained in detail.

3.2 pktcSigDevConfigObjects

   pktcSigDevEchoCancellation - This object identifies the capability
   of echo cancellation on the device.

   pktcSigDevSilenceSuppression - This object specifies if the device
   is capable of silence suppression (Voice Activity Detection).

   pktcSigDevR0Cadence - this object specifies ring cadence 0.

   pktcSigDevR6Cadence - this object specifies ring cadence 6.

   pktcSigDevR7Cadence - this object specifies ring cadence 7.

   pktcSigDefCallSigDscp - this object specifies the default value used
   in the IP header for setting the Differentiated Services Code Point
   (DSCP) value for call signaling.

   pktcSigDefMediaStreamDscp - this object specifies the default value
   used in the IP header for setting the Differentiated Services Code
   Point (DSCP) value for media stream packets.

   pktcSigCapabilityTable - this table specifies list of supported
   signaling types, versions and vendor extensions for MTA.

   pktcSigDefNcsReceiveUdpPort - this object contains the MTA User
   Datagram Protocol (UDP) receive port that is being used for NCS call
   signaling.

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

   pktcSigServiceClassNameUS - this object contains a string indicating
   the Service Class Name to create an Upstream Service Flow for NCS.

   pktcSigServiceClassNameDS - this object contains a string indicating
   the Service Class Name to create an Downstream Service Flow for NCS.

   pktcSigServiceClassNameMask - this object contains a value for the
   Call Signaling Network Mask.

   pktcSigNcsServiceFlowState - this object contains a status value of
   the Call Signaling Service Flow.

   pktcSigDevR1Cadence - this object specifies ring cadence 1.

   pktcSigDevR2Cadence - this object specifies ring cadence 2.

PacketCable/IPCablecom NCS Signaling MIB                  October 2003

   pktcSigDevR3Cadence - this object specifies ring cadence 3.

   pktcSigDevR4Cadence - this object specifies ring cadence 4.

   pktcSigDevR5Cadence - this object specifies ring cadence 5.

   pktcSigDevRgCadence - this object specifies ring cadence rg.

   pktcSigDevRsCadence - this object specifies ring cadence rs.

   pktcSigDevRtCadence - this object specifies ring cadence rt.

   pktcSigDevCIDMode - this ETSI international object selects various modes
   of caller id in common use.

   pktcSigDevCIDFskAfterRing - this ETSI international object sets the delay
   between the end of first ringing and the transmission of caller id
   information.

   pktcSigDevCIDFskAfterDTAS - this ETSI international object sets the delay
   between the dual-tone alert signal and the transmission of caller id
   information.

   pktcSigDevCIDFskAfterRPAS - this ETSI international object sets the delay
   between the ring pulse alert signal and the transmission of caller
   id information.

   pktcSigDevCIDRingAfterFSK - this ETSI international object sets the delay
   between the transmission of caller id information and the first
   ringing pattern.

   pktcSigDevCIDDTASAfterLR - this ETSI international object sets the delay
   between the end of a line reversal and the dual-tone alert signal.

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

   pktcSigDevVmwiMode - this ETSI object selects various modes of visual
   message waiting indicator service in common use.

   pktcSigDevVmwiFskAfterDTAS - this ETSI international object sets the
   delay between the dual-tone alert signal and the transmission of
   visual message waiting information.

   pktcSigDevVwmiFskAfterRPAS - this ETSI international object sets the
   delay between the ring pulse alert signal and the transmission of
   visual message waiting information.

   pktcSigDevVwmiDTASAfterLR - this ETSI international object sets the delay
   between the end of a line reversal and the dual-tone alert signal
   for visual message waiting information.

PacketCable/IPCablecom NCS Signaling MIB                  October 2003

   pktcSigDevRingCadenceTable - this international object provides a
   flexible structure within which to specify a variety of ring
   cadences.

   pktcSigDevStandardRingCadence - this international object specifies
   the standard ring assumed by the MTA.

   pktcSigDevRingSplashCadence - this international object specifies
   the standard splash ring assumed by the MTA.

   pktcSigDevToneTable - this international object specifies a flexible
   structure within which to specify all of the tones used in the MTA.

   pktcNcsEndPntConfigTable - this table describes the PacketCable NCS
   EndPoint configuration. The number of entries in this table
   represents the number of provisioned endpoints.

   pktcSigEndPntConfigTable - this table describes the PacketCable
   EndPoint selected signaling type. The number of entries in this
   table represents the number of provisioned endpoints.

3.3 pktcSigNotification

   pktcSigNotification - this object is used for signaling notification
   and reserved for future use.

3.4 pktcSigConformance

   pktcSigCompliances - this table has one object that has compliance
   statements for devices that implement Signaling on the MTA.

   pktcSigGroups - this table contains group of objects for the common
   portion of the PacketCable NCS and Signaling MIB.

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

   pktcInternationalGroup - this table extends this MIB Module by
   establishing a set of objects designed to support operations over
   the widest range of marketplaces as is possible.

4. Definitions

   PKTC-IETF-SIG-MIB DEFINITIONS ::= BEGIN

   IMPORTS
       MODULE-IDENTITY,
       OBJECT-TYPE,
       Integer32,
       Unsigned32,
       mib-2

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
             FROM SNMPv2-SMI
       InetAddressType,
       InetAddress,
       InetPortNumber
             FROM INET-ADDRESS-MIB
       TEXTUAL-CONVENTION,
       RowStatus,
       TruthValue
             FROM SNMPv2-TC
       OBJECT-GROUP,
       MODULE-COMPLIANCE
             FROM SNMPv2-CONF
       SnmpAdminString
             FROM SNMP-FRAMEWORK-MIB
       ifIndex
             FROM IF-MIB
       Dscp
             FROM DIFFSERV-DSCP-TC;

   pktcSigMib MODULE-IDENTITY
       LAST-UPDATED    "200310020000Z"    "200402180000Z" -- October 2, 2003 February 18, 2004
       ORGANIZATION    "IETF IPCDN Working Group"
       CONTACT-INFO
           "Satish Kumar Mudugere Eswaraiah
            Texas Instruments India (P) Ltd.,
            Golf view, Wind Tunnel Road
            Murugesh Palya
            Bangalore - 560 017, INDIA
            Phone:   +91 80 5269451
            Email:  satish.kumar@ti.com

            Sumanth Channabasappa
            Alopa Networks Inc
            248, McCaslin Bvld #101,
            Louisville, Colorado - 80027

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

            U.S.A.
            Phone: +1 303 604 6595
            Email: Sumanth@alopa.com

            Gordon Beacham
            Motorola BCS/DCG
            6450 Sequence Drive, Bldg. 1
            San Diego, CA 92121, USA
            Phone: +1 858-404-2335
            E-Mail: gordon.beacham@motorola.com

       IETF IPCDN Working Group
            General Discussion: ipcdn@ietf.org
            Subscribe: http://www.ietf.org/mailman/listinfo/ipcdn

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
            Archive: ftp://ftp.ietf.org/ietf-mail-archive/ipcdn
            Co-Chair: Jean-Francois Mule, jf.mule@cablelabs.com
            Co-Chair: Richard Woundy, Richard_Woundy@cable.comcast.com"

       DESCRIPTION
          "This MIB module supplies the basic management
           object for the PacketCable and IPCablecom Signaling
           protocols. This version of the MIB includes
           common signaling and Network Call Signaling
           (NCS) related signaling objects.

           Copyright (C) The Internet Society (2003). (2004). This version of
           this MIB module is part of RFC yyyy; see the RFC itself for
           full legal notices."
   -- RFC Ed: replace yyyy with actual RFC number and remove this note

       REVISION                "200310020000Z"                "200402180000Z"

       DESCRIPTION
          "Initial version, published as RFC yyyy."
   -- RFC Ed: replace yyyy with actual RFC number and remove this note

   ::=  { mib-2 XXX }
   -- RFC Ed: replace XXX with IANA-assigned number and remove this
   -- note

   -- Textual Conventions

   TenthdBm ::= TEXTUAL-CONVENTION
       DISPLAY-HINT "d-1"
       STATUS       current
       DESCRIPTION
           "This data type represents power levels that are normally
            expressed in dBm. Units are in tenths of a dBm;
            for example, -13.5 dBm will be represented as -135."

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       SYNTAX       Integer32

   PktcCodecType ::= TEXTUAL-CONVENTION
       STATUS       current
       DESCRIPTION
           " Textual Convention defines various types of CODECs that
             MAY be supported. The list of CODECs MUST be consistent
             with the Codec RTP MAP Parameters Table in the PacketCable
             CODEC specification. In-line embedded comments below
             contain the Literal Codec Name for each CODEC. The Literal
             Codec Name is the second column of the table with CODEC
             RTP Map Parameters. Literal Codec Name Column contains the
             CODEC name used in LCD of the NCS messages CRCX/MDCX and
             is also used to identify the CODEC in the CMS

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
             Provisioning Specification. RTP Map Parameter Column of
             the Table contains the string used in the media attribute
             line (a=) of the SDP parameters in NCS messages."
       SYNTAX INTEGER {
                      other     (1),
                      unknown   (2),
                      g729      (3),  -- G729
                      reserved  (4),  -- reserved for future use
                      g729E     (5),  -- G729E
                      pcmu      (6),  -- PCMU
                      g726at32  (7),  -- G726-32
                      g728      (8),  -- G728
                      pcma      (9),  -- PCMA
                      g726at16  (10), -- G726-16
                      g726at24  (11), -- G726-24
                      g726at40  (12)  -- G726-40
       }

   PktcRingCadence   ::= TEXTUAL-CONVENTION
       STATUS        current
       DESCRIPTION
           " This object represents a ring cadence and repeatable
             characteristics in bit string format. The ring cadence
             representation starts with the first 1 in the pattern (the
             leading 0s in the MSB are padding and are to be ignored).
             Each bit represents 100ms of tone; 1 is tone, 0 is no
             tone. 64 bits MUST be used for cadence representation. The
             LSB 4 bits of this object are used for representing
             repeatable characteristics. 0000 means repeatable, and
             1000 means non repeatable. During SNMP SET operations, 64
             bits MUST be used, otherwise the MTA MUST reject the
             value. As an example, the hex representation of a ring
             cadence of 0.5 secs on; 4 secs off; repeatable would be:
             0x0001F00000000000."
       SYNTAX  BITS {

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

                    interval1 (0),
                    interval2 (1),
                    interval3 (2),
                    interval4 (3),
                    interval5 (4),
                    interval6 (5),
                    interval7 (6),
                    interval8 (7),
                    interval9 (8),
                    interval10 (9),
                    interval11 (10),
                    interval12 (11),
                    interval13 (12),
                    interval14 (13),

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
                    interval15 (14),
                    interval16 (15),
                    interval17 (16),
                    interval18 (17),
                    interval19 (18),
                    interval20 (19),
                    interval21 (20),
                    interval22 (21),
                    interval23 (22),
                    interval24 (23),
                    interval25 (24),
                    interval26 (25),
                    interval27 (26),
                    interval28 (27),
                    interval29 (28),
                    interval30 (29),
                    interval31 (30),
                    interval32 (31),
                    interval33 (32),
                    interval34 (33),
                    interval35 (34),
                    interval36 (35),
                    interval37 (36),
                    interval38 (37),
                    interval39 (38),
                    interval40 (39),
                    interval41 (40),
                    interval42 (41),
                    interval43 (42),
                    interval44 (43),
                    interval45 (44),
                    interval46 (45),
                    interval47 (46),
                    interval48 (47),
                    interval49 (48),

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

                    interval50 (49),
                    interval51 (50),
                    interval52 (51),
                    interval53 (52),
                    interval54 (53),
                    interval55 (54),
                    interval56 (55),
                    interval57 (56),
                    interval58 (57),
                    interval59 (58),
                    interval60 (59),
                    repeat1    (60),
                    repeat2    (61),
                    repeat3    (62),

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
                    repeat4    (63)
       }

   PktcSigType     ::= TEXTUAL-CONVENTION
       STATUS       current
       DESCRIPTION
           " This object lists the various types of signaling that may
             be supported.
             ncs - Network call signaling is a derivation of MGCP
                   (Media Gateway Control Protocol) defined for
                   IPCablecom/PacketCable MTAs. "
       SYNTAX INTEGER {
                      other(1),
                      reserved(2), -- reserved for future use
                      ncs(3)
       }

   pktcSigMibObjects OBJECT IDENTIFIER ::= { pktcSigMib 1 }
   pktcSigDevConfigObjects OBJECT IDENTIFIER ::=
                                           { pktcSigMibObjects 1 }
   pktcNcsEndPntConfigObjects OBJECT IDENTIFIER ::=
                                           { pktcSigMibObjects 2 }
   pktcSigEndPntConfigObjects   OBJECT IDENTIFIER ::=
                                           { pktcSigMibObjects 3 }
   --
   -- The codec table (pktcSigDevCodecTable) defines the codecs all combinations
   -- of codecs supported by the Media Multimedia Terminal Adapter (MTA). There is one entry
   -- for each codec supported.
   --
   pktcSigDevCodecTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF PktcSigDevCodecEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           " This table describes the MTA supported codec types."
       ::= { pktcSigDevConfigObjects 1 }

   pktcSigDevCodecEntry  OBJECT-TYPE
       SYNTAX      PktcSigDevCodecEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "Each entry represents a supported codec type for the
            MTA."
       INDEX { pktcSigDevCodecIndex }
       ::= { pktcSigDevCodecTable 1 } types. An MTA
             MUST populate this table with all possible combinations of

PacketCable/IPCablecom NCS Signaling MIB                  October 2003

   PktcSigDevCodecEntry  ::= SEQUENCE {
       pktcSigDevCodecIndex    Unsigned32,
       pktcSigDevCodecType     PktcCodecType,
       pktcSigDevCodecMax      Unsigned32
       }

   pktcSigDevCodecIndex  OBJECT-TYPE
       SYNTAX      Unsigned32 (1..255)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           " The index value which uniquely identifies                 February 2004

             codecs it supports for simultaneous operation. For
             example, an entry in the
             pktcSigDevCodecTable."
       ::= { pktcSigDevCodecEntry 1 MTA with two endpoints may be designed with a
             particular DSP and memory architecture that allows it to
             support the following fixed combinations of codecs for
             simultaneous operation:

             Codec Type     Maximum Number of Simultaneous Codecs
             PCMA                             3

             PCMA                             2
             PCMU                             1

             PCMA                             1
             PCMU                             2

             PCMU                             3

             PCMA                             1
             G729                             1

             G729                             2

             PCMU                             1
             G729                             1

             Based on this example, the entries in the codec table
             would be:

             CodecComboIndex pktcSigDevCodecType pktcSigDevCodecMax
                    1               pcma                3
                    2               pcma                2
                    2               pcmu                1
                    3               pcma                1
                    3               pcmu                2
                    4               pcmu                3
                    5               pcma                1
                    5               g729                1
                    6               g729                2
                    7               pcmu                1
                    7               g729                1

             An operator querying this table is able to determine all
             Possible codec combinations the MTA is capable of
             simultaneously supporting."
       ::= { pktcSigDevConfigObjects 1 }

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

   pktcSigDevCodecEntry  OBJECT-TYPE
       SYNTAX      PktcSigDevCodecEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "Each entry represents the maximum number of active
            connections with a particular codec the MTA is capable of
            supporting. Each row is indexed by a composite key
            consisting of a number enumerating the particular codec
            combination and the codec type."
       INDEX { pktcSigDevCodecComboIndex, pktcSigDevCodeType }
       ::= { pktcSigDevCodecTable 1 }

   PktcSigDevCodecEntry  ::= SEQUENCE {
       pktcSigDevCodecComboIndex    Unsigned32,
       pktcSigDevCodecType     PktcCodecType,
       pktcSigDevCodecMax      Unsigned32
       }

   pktcSigDevCodecComboIndex  OBJECT-TYPE
       SYNTAX      Unsigned32 (1..255)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           " The index value which enumerates a  particular codec
             combination in the pktcSigDevCodecTable."
       ::= { pktcSigDevCodecEntry 1 }

   pktcSigDevCodecType  OBJECT-TYPE
       SYNTAX       PktcCodecType
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
           " A codec type supported by this MTA."
       ::= { pktcSigDevCodecEntry 2 }

   pktcSigDevCodecMax  OBJECT-TYPE
       SYNTAX      Unsigned32(1..255)
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           " The maximum number of simultaneous sessions of the
             specific codec that the MTA can support. For example:
             pktcSigDevCodecType     PktcSigDevCodecMax
                    pcma                     2
                    g728                     2
             The MTA can simultaneously support 2 sessions using a
             G.711 (PCMA)
             particular codec AND 2 sessions using a G.728 codec. In
             this example, that the MTA can NOT simultaneously support 1
             G.711 (PCMA) codec and 3 G.728 codecs." support."
       ::= { pktcSigDevCodecEntry 3 }

   --
   -- These are the common signaling related definitions that affect

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

   -- the entire MTA device.
   --

   pktcSigDevEchoCancellation  OBJECT-TYPE
       SYNTAX       TruthValue
       MAX-ACCESS   read-only
       STATUS       current

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       DESCRIPTION
           " This object specifies if the device is capable of echo
             cancellation."
       ::= { pktcSigDevConfigObjects 2 }

   pktcSigDevSilenceSuppression  OBJECT-TYPE
       SYNTAX       TruthValue
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
           " This object specifies if the device is capable of
             silence suppression (Voice Activity Detection)."
   ::= { pktcSigDevConfigObjects 3 }

   pktcSigDevCallerIdSigProtocol  OBJECT-TYPE
       SYNTAX       INTEGER {
                            fsk  (1),
                            dtmf (2)
       }
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This
           "This object identifies the subscriber line protocol used
            for signaling on-hook caller id information."
        REFERENCE
           "EN 300 659-1 Specification"
        DEFVAL { fsk }
   ::= { pktcSigDevConfigObjects 4 }

   --
   -- In the United States Ring Cadences 0, 6, and 7 are custom ring
   -- cadences definable by the system administrator. The following
   -- three objects are used for these definitions.
   --

   pktcSigDevR0Cadence     OBJECT-TYPE
       SYNTAX      PktcRingCadence
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           " This object specifies ring cadence 0 (a user defined
             field) where each bit represents a duration of 100
             milliseconds (6

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

             milliseconds (6 seconds total), except the LSB 4 bits
             which are used to represent repeatable characteristics."
       DEFVAL {{ interval1, interval2, interval3, interval4, interval5,
                 interval6, interval7, interval8, interval9,
                 interval10, interval11, interval12, interval13,
                 interval14, interval15, interval16, interval17,
                 interval18, interval19, interval20 }}
       -- 11111111111111111111000000000000000000000000000000000000000

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       -- 00000
       ::= { pktcSigDevConfigObjects 5 }

   pktcSigDevR6Cadence     OBJECT-TYPE
       SYNTAX      PktcRingCadence
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           " This object specifies ring cadence 6 (a user defined
             field) where each bit represents a duration of 100
             milliseconds (6 seconds total), except the LSB 4 bits
             which are used to represent repeatable characteristics."
       DEFVAL {{ interval1, interval2, interval3, interval4, interval5,
                 interval6, interval7, interval8, interval9,
                 interval10, interval11, interval12, interval13,
                 interval14, interval15, interval16, interval17,
                 interval18, interval19, interval20 }}
       -- 11111111111111111111000000000000000000000000000000000000000
       -- 00000
       ::= { pktcSigDevConfigObjects 6 }

   pktcSigDevR7Cadence     OBJECT-TYPE
       SYNTAX       PktcRingCadence
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This object specifies ring cadence 7 (a user defined
             field) where each bit represents a duration of 100
             milliseconds (6 seconds total), except the LSB 4 bits
             which are used to represent repeatable characteristics."
       DEFVAL {{ interval1, interval2, interval3, interval4, interval5,
                 interval6, interval7, interval8, interval9,
                 interval10, interval11, interval12, interval13,
                 interval14, interval15, interval16, interval17,
                 interval18, interval19, interval20 }}
       -- 11111111111111111111000000000000000000000000000000000000000
       -- 00000
       ::= { pktcSigDevConfigObjects 7 }

   pktcSigDefCallSigDscp  OBJECT-TYPE
       SYNTAX      Dscp  -- RFC 3289: DIFFSERV-DSCP-TC

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           " The default value used in the IP header for setting the
             Differentiated Server Services Code Point (DSCP) value for call
             signaling."
       DEFVAL { 0 }
       ::= { pktcSigDevConfigObjects 8 }

PacketCable/IPCablecom NCS Signaling MIB                  October 2003

   pktcSigDefMediaStreamDscp  OBJECT-TYPE
       SYNTAX      Dscp  -- RFC 3289: DIFFSERV-DSCP-TC
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           " The default value used in the IP header for setting
             the Differentiated Server Services Code Point (DSCP) value for
             media stream packets."
       DEFVAL { 0 }
       ::= { pktcSigDevConfigObjects 9 }

   --
   -- pktcSigCapabilityTable - This table defines the valid signaling
   -- types supported by this MTA.
   --

   pktcSigCapabilityTable    OBJECT-TYPE
       SYNTAX        SEQUENCE OF PktcSigCapabilityEntry
       MAX-ACCESS    not-accessible
       STATUS        current
       DESCRIPTION
           " This table describes the signaling types supported by this
             MTA."
       ::= { pktcSigDevConfigObjects 10 }

   pktcSigCapabilityEntry    OBJECT-TYPE
       SYNTAX        PktcSigCapabilityEntry
       MAX-ACCESS    not-accessible
       STATUS        current
       DESCRIPTION
           " Entries in pktcMtaDevSigCapabilityTable - List of
             supported signaling types, versions and vendor extensions
             for this MTA. Each entry in the list provides for one
             signaling type and version combination. If the device
             supports multiple versions of the same signaling type it
             will require multiple entries."
       INDEX { pktcSignalingIndex }
       ::= { pktcSigCapabilityTable 1 }

   PktcSigCapabilityEntry  ::= SEQUENCE {

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       pktcSignalingIndex             Unsigned32,
       pktcSignalingType              PktcSigType,
       pktcSignalingVersion           SnmpAdminString,
       pktcSignalingVendorExtension   SnmpAdminString
       }

   pktcSignalingIndex       OBJECT-TYPE
       SYNTAX        Unsigned32 (1..255)

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       MAX-ACCESS    not-accessible
       STATUS        current
       DESCRIPTION
           " The index value which uniquely identifies an entry in the
             pktcSigCapabilityTable."
       ::= { pktcSigCapabilityEntry 1 }

   pktcSignalingType      OBJECT-TYPE
       SYNTAX        PktcSigType
       MAX-ACCESS    read-only
       STATUS        current
       DESCRIPTION
           " This object identifies the type of signaling used. This
             value has to be associated with a single signaling
             version."
       ::= { pktcSigCapabilityEntry 2 }

   pktcSignalingVersion      OBJECT-TYPE
       SYNTAX        SnmpAdminString
       MAX-ACCESS    read-only
       STATUS        current
       DESCRIPTION
           " Provides the version of the signaling type - reference
             pktcSignalingType. Examples would be 1.0 or 2.33 etc."
       ::= { pktcSigCapabilityEntry 3 }

   pktcSignalingVendorExtension      OBJECT-TYPE
       SYNTAX        SnmpAdminString
       MAX-ACCESS    read-only
       STATUS        current
       DESCRIPTION
           " The vendor extension allows vendors to provide a list of
             additional capabilities, vendors can decide how to encode
             these extensions, although space separated text is
             suggested."
       ::= { pktcSigCapabilityEntry 4 }

   pktcSigDefNcsReceiveUdpPort  OBJECT-TYPE
       SYNTAX      InetPortNumber (1025..65535)
       MAX-ACCESS  read-only
       STATUS      current

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       DESCRIPTION
           " This object contains the MTA User Datagram Protocol (UDP)
             receive port that is being used for NCS call signaling.
             This object should only be changed by the configuration
             file."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL { 2427 }

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       ::= { pktcSigDevConfigObjects 11 }

   pktcSigServiceClassNameUS  OBJECT-TYPE
        SYNTAX     SnmpAdminString (SIZE (0..15))
        MAX-ACCESS  read-write
        STATUS     current
        DESCRIPTION
            " This object contains a string indicating the Service
              Class Name to create an Upstream Service Flow for NCS.
              If the object has an empty string value then the NCS SF
              is not created and the best effort primary SF is used for
              NCS data. If this object is set to a non-empty (non-zero
              length) string, the MTA MUST create the NCS SF if it does
              not currently exist and the pktcSigServiceClassNameMask
              object has a non-zero value. If this object is
              subsequently set to an empty (zero-length) string, the
              MTA MUST delete the NCS SF if it exists. Setting this
              object to a different value does not cause the US SF to
              be re-created. The string MUST contain printable ASCII
              characters. The length of the string does not include a
              terminating zero. The MTA MUST append a terminating zero
              when the MTA creates the service flow."
        DEFVAL { "" }
        ::= { pktcSigDevConfigObjects 12 }

   pktcSigServiceClassNameDS  OBJECT-TYPE
        SYNTAX     SnmpAdminString (SIZE (0..15))
        MAX-ACCESS  read-write
        STATUS     current
        DESCRIPTION
            " This object contains a string indicating the Service
              Class Name to create a Downstream Service Flow for NCS.
              If the object has an empty string value then the NCS SF
              is not created and the best effort primary SF is used for
              NCS data. If this object is set to a non-empty (non-zero
              length) string, the MTA MUST create the NCS SF if it does
              not currently exist and the pktcSigServiceClassNameMask
              object has a non-zero value. If this object is
              subsequently set to an empty (zero-length) string, the
              MTA MUST delete the NCS SF if it exists. Setting this
              object to a different value does not cause the DS SF to

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

              be re-created. The string MUST contain printable ASCII
              characters. The length of the string does not include a
              terminating zero. The MTA MUST append a terminating zero
              when the MTA creates the service flow."
        DEFVAL { "" }
        ::= { pktcSigDevConfigObjects 13 }

   pktcSigServiceClassNameMask  OBJECT-TYPE

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
        SYNTAX     Integer32
        MAX-ACCESS  read-write
        STATUS     current
        DESCRIPTION
            " This object contains a value used for the NCS Call
              Signaling classifier mask. If this object is set to a
              zero value, the MTA MUST delete both NCS SFs. When
              this object is set to a non-zero value, the MTA MUST
              create the NCS SF for which the corresponding MIB object
              (pktcSigServiceClassNameUS  or pktcSigServiceClassNameDS)
              has a non-empty value, if the NCS SF does not already
              exist."
        DEFVAL { 0 }
        ::= { pktcSigDevConfigObjects 14 }

   pktcSigNcsServiceFlowState OBJECT-TYPE
        SYNTAX     INTEGER {
                  notactive  (1),
                  active     (2),
                  error      (3)
        }
        MAX-ACCESS read-only
        STATUS     current
        DESCRIPTION
            "This object contains a status value of the Call Signaling
             Service Flow.
             - notactive indicates that the NCS SF is not being used,
               and has not tried to be created,
             - active indicates that the NCS SF is in use,
             - error indicates that the NCS SF creation resulted in
               an error and the best effort channel is used for NCS
               Signaling."
             ::= { pktcSigDevConfigObjects 15 }

   pktcSigDevR1Cadence     OBJECT-TYPE
       SYNTAX      PktcRingCadence
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           " This object specifies ring cadence 1 (a user defined
             field) where each bit represents a duration of 100

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

             milliseconds (6 seconds total), except the LSB 4 bits
             which are used to represent repeatable characteristics."
       DEFVAL {{ interval1, interval2, interval3, interval4, interval5,
                 interval6, interval7, interval8, interval9,
                 interval10, interval11, interval12, interval13,
                 interval14, interval15, interval16, interval17,
                 interval18, interval19, interval20 }}
       -- 11111111111111111111000000000000000000000000000000000000000

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       -- 00000
       ::= { pktcSigDevConfigObjects 16 }

   pktcSigDevR2Cadence     OBJECT-TYPE
       SYNTAX       PktcRingCadence
       MAX-ACCESS    read-write
       STATUS        current
       DESCRIPTION
           " This object specifies ring cadence 2 (a user defined
             field) where each bit represents a duration of 100
             milliseconds (6 seconds total), except the LSB 4 bits
             which are used to represent repeatable characteristics."
       DEFVAL {{ interval1, interval2, interval3, interval4, interval5,
                 interval6, interval7, interval8, interval13,
                 interval14, interval15, interval16, interval17,
                 interval18, interval19, interval20 }}
       -- 11111111000011111111000000000000000000000000000000000000000
       -- 00000
       ::= { pktcSigDevConfigObjects 17 }

   pktcSigDevR3Cadence     OBJECT-TYPE
       SYNTAX       PktcRingCadence
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This object specifies ring cadence 3 (a user defined
             field) where each bit represents a duration of 100
             milliseconds (6 seconds total), except the LSB 4 bits
             which are used to represent repeatable characteristics."
       DEFVAL {{ interval1, interval2, interval3, interval4, interval7,
                 interval8, interval9, interval10, interval13,
                 interval14, interval15, interval16, interval17,
                 interval18, interval19, interval20 }}
       -- 11110011110011111111000000000000000000000000000000000000000
       -- 00000
       ::= { pktcSigDevConfigObjects 18 }

   pktcSigDevR4Cadence     OBJECT-TYPE
       SYNTAX       PktcRingCadence
       MAX-ACCESS   read-write
       STATUS       current

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       DESCRIPTION
           " This object specifies ring cadence 4 (a user defined
             field) where each bit represents a duration of 100
             milliseconds (6 seconds total), except the LSB 4 bits
             which are used to represent repeatable characteristics."
       DEFVAL {{ interval1, interval2, interval3, interval6, interval7,
                 interval8, interval9, interval10, interval11,
                 interval12, interval13, interval14, interval15,

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
                 interval18, interval19, interval20 }}
       -- 11100111111111100111000000000000000000000000000000000000000
       -- 00000
       ::= { pktcSigDevConfigObjects 19 }

   pktcSigDevR5Cadence     OBJECT-TYPE
       SYNTAX       PktcRingCadence
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This object specifies ring cadence 5 (a user defined
             field) where each bit represents a duration of 100
             milliseconds, except the LSB 4 bits which are used to
             represent repeatable characteristics."
       DEFVAL {{ interval1, interval2, interval3, interval4, interval5,
                 repeat1 }}
       -- 11111000000000000000000000000000000000000000000000000000000
       -- 01000
       ::= { pktcSigDevConfigObjects 20 }

   pktcSigDevRgCadence     OBJECT-TYPE
       SYNTAX       PktcRingCadence
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This object specifies ring cadence rg (a user defined
             field) where each bit represents a duration of 100
             milliseconds (6 seconds total), except the LSB 4 bits
             which are used to represent repeatable characteristics." characteristics.
             This object is required for the L line package."
       DEFVAL {{ interval1, interval2, interval3, interval4, interval5,
                 interval6, interval7, interval8, interval9,
                 interval10, interval11, interval12, interval13,
                 interval14, interval15, interval16, interval17,
                 interval18, interval19, interval20 } }
       -- 11111111111111111111000000000000000000000000000000000000000
       -- 00000
       ::= { pktcSigDevConfigObjects 21 }

   pktcSigDevRsCadence     OBJECT-TYPE
       SYNTAX       PktcRingCadence

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This object specifies ring cadence rs (a user defined
             field) where each bit represents a duration of 100
             milliseconds (6 seconds total), except the LSB 4 bits
             which are used to represent repeatable characteristics.
             The MTA MUST reject any attempt to make this object
             repeatable."

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
             repeatable. This object is required for the L line
             package."
       DEFVAL {{ interval1, interval2, interval3, interval4, interval5,
                 repeat1 }}
       -- 11111000000000000000000000000000000000000000000000000000000
       -- 01000
       ::= { pktcSigDevConfigObjects 22 }

   pktcSigDevRtCadence     OBJECT-TYPE
       SYNTAX       PktcRingCadence
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This object specifies ring cadence rt (a user defined
             field) where each bit represents a duration of 100
             milliseconds (6 seconds total), except the LSB 4 bits
             which are used to represent repeatable characteristics."
       DEFVAL {{ interval1, interval2, interval3, interval4, interval5,
                 interval6, interval7, interval8, interval9,
                 interval10, interval11, interval12, interval13,
                 interval14, interval15, interval16, interval17,
                 interval18, interval19, interval20 } }
       -- 11111111111111111111000000000000000000000000000000000000000
       -- 00000
       ::= { pktcSigDevConfigObjects 23 }

   pktcSigPowerRingFrequency    OBJECT-TYPE
       SYNTAX       INTEGER {
                    f20Hz(1),
                    f25Hz(2),
                    f33Point33Hz(3),
                    f50Hz(4),
                    f15Hz(5),
                    f16Hz(6),
                    f22Hz(7),
                    f23Hz(8),
                    f45Hz(9)
       }
       UNITS "Hertz"
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
           " This object must only be set via the configuration file
             during the provisioning process. The power ring frequency
             is the frequency at which the sinusoidal voltage must
             travel down the twisted pair to make terminal equipment
             ring. Different countries define different electrical
             characteristics to make terminal equipment ring."
       REFERENCE
             "EN 300 001 contains a list of frequency ranges that

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
              are defined for each country."
       DEFVAL { f20Hz }
       ::= { pktcSigDevConfigObjects 24 23 }

   pktcSigPulseSignalTable    OBJECT-TYPE
       SYNTAX       SEQUENCE OF PktcSigPulseSignalEntry
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

           " The Pulse signal table defines the pulse signal operation.
             There are four nine types of international pulse signals,
             initial ring, meter pulse, reverse polarity and no
             battery. The Pulse duration type is specific and it is
             specified
             with each signal having a 1 to 32 value. set of provisionable parameters.
             The values of the MIB objects in this table take effect
             only if these parameters are not defined via signaling, in
             which case the latter determines the values of the
             parameters. This object is required for the E line
             package. Signals defined in this table are triggered using
             the E line package.
             Objects in this table do not persist across MTA reboots."
       REFERENCE
           "TS 101 909-4 Specification"
       ::= { pktcSigDevConfigObjects 25 24 }

   pktcSigPulseSignalEntry    OBJECT-TYPE
       SYNTAX       PktcSigPulseSignalEntry
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION
           " Unique value ranging from 1 to 32 that will correspond to This object defines the set of parameters associated with
             each particular value specified of pktcSigPulseSignalType. Each
             entry in the pktcSigPulseSignalTable is indexed by the operator."
             pktcSigPulseSignalType object."
       INDEX { pktcSigPulseSignalIndex }
       ::= { pktcSigPulseSignalTable 1 }

   PktcSigPulseSignalEntry ::= SEQUENCE {
           pktcSigPulseSignalIndex             Unsigned32,
           pktcSigPulseSignalDuration          Unsigned32,
           pktcSigPulseSignalType              INTEGER,
           pktcSigPulseSignalDbLevel           TenthdBm,
           pktcSigPulseSignalFrequency         INTEGER,
           pktcSigPulseSignalRepeatCount
           pktcSigPulseSignalDbLevel           TenthdBm,
           pktcSigPulseSignalDuration          Unsigned32,
           pktcSigPulseSignalPauseDuration     Unsigned32}

   pktcSigPulseSignalIndex    OBJECT-TYPE
       SYNTAX
           pktcSigPulseSignalPulseInterval     Unsigned32,
           pktcSigPulseSignalRepeatCount       Unsigned32 (1..32)
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION
           " The table index equivalent to the operator specific pulse
             type and duration."
       ::= { pktcSigPulseSignalEntry 1
   }

   pktcSigPulseSignalDuration

   pktcSigPulseSignalType    OBJECT-TYPE
       SYNTAX       Unsigned32 (50..5000)
       UNITS        "Milliseconds"       INTEGER
                    {
                        initialRing(1),
                        pulseLoopClose(2),
                        pulseLoopOpen(3),
                        enableMeterPulse(4),
                        meterPulseBurst(5),
                        pulseNoBattery(6),
                        pulseNormalPolarity(7),
                        pulseReducedBattery(8),
                        pulseReversePolarity(9)
                    }
       MAX-ACCESS   read-write   not-accessible

PacketCable/IPCablecom NCS Signaling MIB                  October 2003                 February 2004

       STATUS       current
       DESCRIPTION
           " The There are nine types of international pulse duration varies according to the operator and
             country." signals."
       REFERENCE
           "EN 300 001 324-1 Specification"
            DEFVAL { 1000 }

       ::= {pktcSigPulseSignalEntry 2 { pktcSigPulseSignalEntry 1 }

   pktcSigPulseSignalType

   pktcSigPulseSignalFrequency    OBJECT-TYPE
       SYNTAX       INTEGER {
                        initialRing(1),
                        meterPulse(2),
                        reversePolarity(3),
                        noBattery(4)
                    twentyfive (1),
                    twelvethousand(2),
                    sixteenthousand(3)
       }
       UNITS        "Hertz"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " There are four types This object is only applicable to the initialRing,
             enableMeterPulse, and meterPulseBurst signal type. This
             object identifies the frequency of international pulse signals." the generated signal.
             The following table defines the default values for this
             object depending on signal type:
             pktcSigPulseSignalType     Default
             initialRing                25
             enableMeterPulse           16000
             meterPulseBurst            16000
             The value of twentyfive must only be used for the
             initialRing signal type. The values of twelvethousand and
             sixteenthousand must only be used for enableMeterPulse and
             meterPulseBurst signal types."
       REFERENCE
           "EN 300 001 Specification"
       DEFVAL { initialRing }
            ::= { pktcSigPulseSignalEntry 3 } 2}

   pktcSigPulseSignalDbLevel    OBJECT-TYPE
       SYNTAX       TenthdBm (-200..30) (-250..152)
       UNITS        "dbm"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This object is only applies if pktcSigPulseSignalType =
             meterPulse. applicable to the enableMeterPulse and
             meterPulseBurst signal types. This is the decibel level
             for each frequency at which the meter
             pulse tones could be generated. Example:
             pktcSigPulseSignalType     pktcSigPulseSignalDbLevel
             initialRing                        not used
             meterPulse                         -60
             reversePolarity                    not used
             noBattery                          not used" generated at
             the a and b terminals (TE connection point)."
       REFERENCE
           "EN 300 001 Specification"
       DEFVAL { -60 -135 }
       ::={pktcSigPulseSignalEntry 4 3 }

   pktcSigPulseSignalFrequency    OBJECT-TYPE
       SYNTAX       INTEGER {
                    zero (1),
                    twelvethousand(2),

PacketCable/IPCablecom NCS Signaling MIB                  October 2003

                    sixteenthousand(3)
       }                 February 2004

   pktcSigPulseSignalDuration    OBJECT-TYPE
       SYNTAX       Unsigned32 (0..5000)
       UNITS        "Hertz"        "Milliseconds"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This object only applies if pktcSigPulseSignalType =
             meterPulse. This is the frequency at which specifies the meter pulse
             could be generated. Example:
             pktcSigPulseSignalType     pktcSigPulseSignalDbLevel duration for each
             signal type. In addition, the MTA must accept the values
             in the incremental steps specific for each signal type.
             The following table defines the default values and the
             incremental steps for this object depending on the signal
             type.
             pktcSigPulseSignaltype  Default (ms)   Increment (ms)
             initialRing                          not used
             meterPulse                           sixteenthousand
             reversePolarity                      not used
             noBattery                            not used.
             Note:                 200             50
             pulseLoopClose              200             10
             pulseLoopOpen               200             10
             enableMeterPulse            150             10
             meterPulseBurst             150             10
             pulseNoBattery              200             10
             pulseNormalPolarity         200             10
             pulseReducedBattery         200             10
             pulseReversePolarity        200             10"
       REFERENCE
           "EN 300 324-1 Specification"
            ::= {pktcSigPulseSignalEntry 4 }

   pktcSigPulseSignalPulseInterval     OBJECT-TYPE
       SYNTAX       Unsigned32 (0..5000)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This object specifies the repeat interval, or the period
             for each signal type. In addition, the MTA must accept
             the values in the incremental steps specific for each
             signal type. The zero value is used to turn off meter pulse." following table defines the default
             values and the incremental steps for this object depending
             on the signal type.
             pktcSigPulseSignaltype  Default (ms)   Increment (ms)
             initialRing                 200             50
             pulseLoopClose             1000             10
             pulseLoopOpen              1000             10
             enableMeterPulse           1000             10
             meterPulseBurst            1000             10
             pulseNoBattery             1000             10
             pulseNormalPolarity        1000             10
             pulseReducedBattery        1000             10
             pulseReversePolarity       1000             10"

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       REFERENCE
           "EN 300 001 324-1 Specification"
       DEFVAL { sixteenthousand }
            ::= { pktcSigPulseSignalEntry 5}

   pktcSigPulseSignalRepeatCount    OBJECT-TYPE
       SYNTAX       Unsigned32 (0..5000)
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This is the repeat count, which signifies object specifies how many times to repeat a pulse.
             This object is not used by the pulse."
       DEFVAL { 0 }
       ::={ pktcSigPulseSignalEntry 6 }

   pktcSigPulseSignalPauseDuration    OBJECT-TYPE
       SYNTAX       Unsigned32 (50..5000)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " enableMeterPulse signal
             type and as such must have a value of zero. The pause duration between pulses varies according to following
             table defines the
             operator default values and country."
       ::= { the valid ranges for
             this object depending on the signal type.
             pktcSigPulseSignaltype  Default   Range
             initialRing                1       1-5
             pulseLoopClose             1       1-50
             pulseLoopOpen              1       1-50
             enableMeterPulse           0       Not Used
             meterPulseBurst            1       1-50
             pulseNoBattery             1       1-50
             pulseNormalPolarity        1       1-50
             pulseReducedBattery        1       1-50
             pulseReversePolarity       1       1-50"
       ::={ pktcSigPulseSignalEntry 7 6 }

   pktcSigDevCIDMode    OBJECT-TYPE
       SYNTAX       INTEGER {
                    duringRingingETS(1),
                    dtAsETS(2),
                    rpAsETS(3),
                    lrAsETS(4)
                    }
       MAX-ACCESS read-write
       STATUS current

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       DESCRIPTION
           " This object is used for ETSI international systems only.
             For on-hook Caller ID, pktcSigDevCIDMode selects the
             method of Caller ID. For the duringRingingETS method, the
             FSK containing the Caller ID information is sent between
             the first and second ring pattern. For the dtAsETS,
             rpAsETS, and lrAsETS methods, the FSK containing the
             Caller ID information is sent before the first ring
             pattern. For the dtAsETS method, the FSK is sent after the
             Dual Tone Alert Signal.
             For the rpAsETS method, the FSK is sent after a Ring
             Pulse. For the lrAsETS method, the Line Reversal occurs
             first, then the Dual Tone Alert Signal, and finally the
             FSK is sent."

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       DEFVAL { dtAsETS }
       ::= {pktcSigDevConfigObjects 26 25 }

   pktcSigDevCIDFskAfterRing    OBJECT-TYPE
       SYNTAX       Unsigned32 (0..2000) (50..2000)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This object is used for ETSI international systems only. This
             object specifies the delay between the end of first
             ringing pattern and the start of the transmission of the
             FSK containing the Caller ID information. It is only used
             when pktcSigDevCIDMode is duringRingingETS.
             pktcSigDevCIDMode     pktcSigDevCIDFskAfterRing
             duringringingETS              550 ms
             dtAsETS                       not used
             rpAsETS                       not used
             lrAsETS                       not used"
       REFERENCE
           "EN 300 659-1 Specification"
       DEFVAL { 550 }
       ::= {pktcSigDevConfigObjects 27 26 }

   pktcSigDevCIDFskAfterDTAS    OBJECT-TYPE
       SYNTAX       Unsigned32 (0..500) (45..500)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This object is used for ETSI international systems only. This
             object specifies the delay between the end of the Dual
             Tone Alert Signal (DT-AS) and the start of the
             transmission of the FSK containing the Caller ID
             information. This object is only used when
             pktcSigDevCIDMode is dtAsETS or lrAsETS.
             pktcSigDevCIDMode     pktcSigDevCIDFskAfterDTAS

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
             duringringingETS               not used
             dtAsETS                        50 ms
             rpAsETS                        not used
             lrAsETS                        50 ms"
       REFERENCE
           "EN 300 659-1 Specification"
       DEFVAL { 50 }
       ::= {pktcSigDevConfigObjects 28 27 }

   pktcSigDevCIDFskAfterRPAS    OBJECT-TYPE
       SYNTAX       Unsigned32 (500..800)
       UNITS        "Milliseconds"

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This object is used for ETSI international systems only. This
             object specifies the delay between the end of the Ring
             Pulse Alert Signal (RP-AS) and the start of the
             transmission of the FSK containing the Caller ID
             information. This object is only used when
             pktcSigDevCIDMode is rpAsETS.
             pktcSigDevCIDMode     pktcSigDevCIDFskAfterRPAS
             duringringingETS               not used
             dtAsETS                        not used
             rpAsETS                        650 ms
             lrAsETS                        not used"
       REFERENCE
           "EN 300 659-1 Specification"
       DEFVAL { 650 }
       ::= {pktcSigDevConfigObjects 29 28 }

   pktcSigDevCIDRingAfterFSK    OBJECT-TYPE
       SYNTAX       Unsigned32 (0..500) (50..500)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This object is used for ETSI international systems only. This
             object specifies the delay between the end of the complete
             transmission of the FSK containing the Caller ID
             information and the start of the first ring pattern. It is
             only used when pktcSigDevCIDMode is dtAsETS, rpAsETS or
             lrAsETS.
             pktcSigDevCIDMode     pktcSigDevCIDFskAfterFSK
             duringringingETS              not used
             dtAsETS                       250 ms
             rpAsETS                       250 ms
             lrAsETS                       250 ms"
       REFERENCE
           "EN 300 659-1 Specification"

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       DEFVAL { 250 }
       ::= {pktcSigDevConfigObjects 30 29 }

   pktcSigDevCIDDTASAfterLR    OBJECT-TYPE
       SYNTAX       Unsigned32 (0..655) (50..655)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This object is used for ETSI international systems only. This
             object specifies the delay between the end of the Line

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

             Reversal and the start of the Dual Tone Alert Signal
             (DT-AS). This object is only used when pktcSigDevCIDMode
             is lrAsETS.
             pktcSigDevCIDMode     pktcSigDevCIDFskAfterLR
             duringringingETS              not used
             dtAsETS                       not used
             rpAsETS                       not used
             lrAsETS                       250 ms"
       REFERENCE
           "EN 300 659-1 Specification"
       DEFVAL { 250 }

       ::= {pktcSigDevConfigObjects 31 }

   pktcSigDevVmwiMode    OBJECT-TYPE
       SYNTAX       INTEGER {
                    dtAsETS(1),
                    rpAsETS(2),
                    lrAsETS(3)
                    lrAsETS(3),
                    osi(4)
                    }
       MAX-ACCESS read-write
       STATUS current
       DESCRIPTION
           " This object is used for ETSI systems only. For visual message waiting indicator (VMWI),
             pktcSigDevVmwiMode selects the alerting signal method. For
             the dtAsETS, rpAsETS, lrAsETS, and lrAsETS OSI methods,
             the FSK containing the VMWI information is sent after an
             alerting signal. For the dtAsETS method, the FSK is sent
             after the Dual Tone Alert Signal. For the rpAsETS method,
             the FSK is sent after a Ring Pulse. For the lrAsETS
             method, the Line Reversal occurs first, then the Dual Tone
             Alert Signal, and finally the FSK is sent." sent. For the OSI
             method, the FSK is sent after the Open Switching
             Interval."
       DEFVAL { dtAsETS }
       ::= {pktcSigDevConfigObjects 32 }

   pktcSigDevVmwiFskAfterDTAS    OBJECT-TYPE
       SYNTAX       Unsigned32 (45..500)
       UNITS        "Milliseconds"

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This object is used for ETSI international systems only. This
             object specifies the delay between the end of the Dual
             Tone Alert Signal (DT-AS) and the start of the
             transmission of the FSK containing the VMWI information.
             This object is only used when pktcSigDevVmwiMode is

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

             dtAsETS or lrAsETS.
             pktcSigDevVmwiMode     pktcSigDevVmwiFskAfterDTAS
             dtAsETS                        50 ms
             rpAsETS                        not used
             lrAsETS                        50 ms"
       REFERENCE
           "EN 300 659-1 Specification"
       DEFVAL { 50 }
       ::= {pktcSigDevConfigObjects 33 }

   pktcSigDevVmwiFskAfterRPAS    OBJECT-TYPE
       SYNTAX       Unsigned32 (500..800)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This object is used for ETSI international systems only. This
             object specifies the delay between the end of the Ring
             Pulse Alert Signal (RP-AS) and the start of the
             transmission of the FSK containing the VMWI information.
             This object is only used when pktcSigDevVmwiMode is
             rpAsETS.
             pktcSigDevVmwiMode     pktcSigDevVmwiFskAfterRPAS
             dtAsETS                        not used
             rpAsETS                        650 ms
             lrAsETS                        not used "
       REFERENCE
           "EN 300 659-1 Specification"
       DEFVAL { 650 }
       ::= {pktcSigDevConfigObjects 34 }

   pktcSigDevVmwiDTASAfterLR    OBJECT-TYPE
       SYNTAX       Unsigned32 (0..655) (50..655)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This object is used for ETSI international systems only. This
             object specifies the delay between the end of the Line
             Reversal and the start of the Dual Tone Alert Signal
             (DT-AS) for

PacketCable/IPCablecom NCS Signaling MIB                  October 2003 VMWI information. This object is only used
             when pktcSigDevVmwiMode is lrAsETS.
             pktcSigDevVmwiMode     pktcSigDevVmwiDTASAfterLR
             dtAsETS                        not used
             rpAsETS                        not used
             lrAsETS                        250 ms "
       REFERENCE
           "EN 300 659-1 Specification"

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       DEFVAL { 250 }
       ::= {pktcSigDevConfigObjects 35 }

   pktcSigDevRingCadenceTable    OBJECT-TYPE
       SYNTAX       SEQUENCE OF PktcSigDevRingCadenceEntry
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION
           " In V5.2, Cadence rings are defined by the telco governing
             body for each country. The MTA must be able to support
             various ranges of cadence patterns and cadence periods.
             The MTA will be able to support country specific
             provisioning of the cadence and idle period. There will be
             at most 3 on/off transitions per cadence period. Each
             cadence pattern will be assigned a unique value ranging
             from 1-128 (inclusive) corresponding to the value of x
             plus one, where x is the value sent by in the LE
             SIGNAL message plus one. cr(x) signal
             requested per the appropriate NCS message, and defined in
             the E package. The MTA will derive the cadence periods
             from the ring Cadence table entry as provisioned by the
             customer. The MTA is allowed to provide appropriate
             default values for each of the ring cadences. This table
             only needs to be supported when the MTA implements the NCS
             E package. Objects in this table do not persist across MTA
             reboots."
       REFERENCE
           "TS 101 909-4 Specification"
       ::= { pktcSigDevConfigObjects 36 }

   pktcSigDevRingCadenceEntry    OBJECT-TYPE
       SYNTAX       PktcSigDevRingCadenceEntry
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION
           " Unique value ranging from 1 to 128 that corresponds to the
             value sent by the LE (plus one) based on country specific
             cadences, one row per cadence cycle. In any given system
             implementation for a particular country, it is anticipated
             that a small number of ring cadences will be in use. Thus,
             this table most likely will not be populated to its full
             128-row size."
       INDEX { pktcSigDevRingCadenceIndex }
       ::= { pktcSigDevRingCadenceTable 1 }

   PktcSigDevRingCadenceEntry ::= SEQUENCE {
           pktcSigDevRingCadenceIndex       Unsigned32,
           pktcSigDevRingCadence            OCTET STRING
       }

PacketCable/IPCablecom NCS Signaling MIB                  October 2003                 February 2004

   pktcSigDevRingCadenceIndex    OBJECT-TYPE
       SYNTAX       Unsigned32 (1..128)
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION
           " The table index equivalent to the country specific cadence
             (1 - 128)."
       ::= { pktcSigDevRingCadenceEntry 1 }

   pktcSigDevRingCadence    OBJECT-TYPE
       SYNTAX       OCTET STRING (SIZE(2..28)) (SIZE(4..36))
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This is the Ring Cadence Octet String. The first octet two
             octets of the bit string represents represent the length in bits of
             the duration of the cadence. The third octet is used to
             represent repeatable charcteristics. 00000000 means
             repeatable, and 10000000 means non repeatable. Each Bit
             after the first third octet represents 50 ms and 1 represents
             ring and 0 represents silent. The first bit of the second fourth
             octet is the first bit of the ring cadence. Only 216 A total of 264
             Bits can be set total to represent 10800 13200 ms of total cadence cycle."
             cycle. This object is required for the E line package."
       ::= { pktcSigDevRingCadenceEntry 2 }

   pktcSigDevStandardRingCadence    OBJECT-TYPE
       SYNTAX       OCTET STRING (SIZE(2..28)) (SIZE(4..36))
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This is the Ring Cadence Octet String for the standard
             ring. The first octet two octets of the bit string represents represent
             the length in bits of the duration of the cadence cadence. The
             third octet is used to represent repeatable
             characteristics. 00000000 means repeatable, and 10000000
             means non repeatable. Each Bit after the first third octet
             represents 50 ms and 1 represents ring and 0 represents
             silent. The first bit of the second fourth octet is the first bit
             of the ring cadence. Only 216 A total of 264 Bits can be set total to
             represent 10800 13200 ms of total cadence
             cycle." cycle. The MTA MUST provide
             a default value for this object in accordance with
             published specifications for the country of operation.
             This object is required for the E line package."
       REFERENCE
           "TR 101 183 Specification"
       ::= { pktcSigDevConfigObjects  37 }

   pktcSigDevRingSplashCadence    OBJECT-TYPE

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       SYNTAX       OCTET STRING (SIZE(2..28)) (SIZE(4..36))
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This is the Ring Cadence Octet String for splash ring. The
             first octet two octets of the bit string represents represent the length in
             bits of the duration of the cadence. The third octet is
             used to represent repeatable characteristics. 00000000
             means repeatable, and 10000000 means non repeatable. Each
             Bit after the
             first third octet represents 50 ms and 1
             represents ring and 0 represents silent. The first bit of
             the second fourth octet is

PacketCable/IPCablecom NCS Signaling MIB                  October 2003 the first bit of the ring cadence. Only 216 A
             total of 264 Bits can be set total to represent 10800 13200 ms of total
             cadence cycle." cycle. The MTA MUST provide a default value for
             this object in accordance with published specifications
             for the country of operation. This object is required for
             the E line package."
       REFERENCE
           "TR 101 183 Specification"
       ::= { pktcSigDevConfigObjects  38 }

   pktcSigDevToneTable    OBJECT-TYPE
       SYNTAX       SEQUENCE OF PktcSigDevToneEntry
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION
           " The Tone Table defines the various tone operations. Any
             definition of the tones callWaiting1-4 in this table
             should just contain the audible tone itself and NOT
             contain the delay between tones or the tone repeat count.
             The delay between tones or the repeat count is controlled
             by the MIB objects pktcNcsEndPntConfigCallWaitingDelay,
             and pktcNcsEndPntConfigCallWaitingMaxRep. The MTA MUST
             make sure that, after the provisioning cycle, the table is
             fully populated (i.e., for each possible index, an entry
             MUST be defined) using reasonable defaults for each row
             that was not defined by the provisioning information.
             Objects in this table do not persist across MTA reboots."
       REFERENCE
           "NCS Specification, TS 101 909-4 Specification"
       ::= { pktcSigDevConfigObjects 39 }

   pktcSigDevToneEntry    OBJECT-TYPE
       SYNTAX       PktcSigDevToneEntry
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION
           " Unique value ranging from 0 1 to 38 21 that will correspond to
             the different tone types that are being supported by the

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

             device. These tones can be provisioned based on country
             specific needs."
       INDEX { pktcSigDevToneType }
       ::= { pktcSigDevToneTable 1 }

   PktcSigDevToneEntry ::= SEQUENCE {
       pktcSigDevToneType                      INTEGER,
       pktcSigDevToneDbLevel                   Integer32,                   TenthdBm,
       pktcSigDevToneFreqType                  INTEGER,
       pktcSigDevToneNumFrequencies            Unsigned32,
       pktcSigDevToneFirstFrequency            Unsigned32,
       pktcSigDevToneSecondFrequency           Unsigned32,
       pktcSigDevToneThirdFrequency            Unsigned32,
       pktcSigDevToneFourthFrequency           Unsigned32,
       pktcSigDevToneNumOnOffTimes             Unsigned32,
       pktcSigDevToneFirstToneOn               Unsigned32,
       pktcSigDevToneFirstToneOff              Unsigned32,
       pktcSigDevToneSecondToneOn              Unsigned32,
       pktcSigDevToneSecondToneOff             Unsigned32,
       pktcSigDevToneThirdToneOn               Unsigned32,
       pktcSigDevToneThirdToneOff              Unsigned32,
       pktcSigDevToneFourthToneOn              Unsigned32,
       pktcSigDevToneFourthToneOff             Unsigned32,

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       pktcSigDevToneWholeToneRepeatCount      Unsigned32,
       pktcSigDevToneSteady                    TruthValue
       }

   pktcSigDevToneType        OBJECT-TYPE
       SYNTAX       INTEGER {
                    dtmf0(0),
                    dtmf1(1),
                    dtmf2(2),
                    dtmf3(3),
                    dtmf4(4),
                    dtmf5(5),
                    dtmf6(6),
                    dtmf7(7),
                    dtmf8(8),
                    dtmf9(9),
                    dtmfToneStar(10),
                    dtmfTonePound(11),
                    dtmfA(12),
                    dtmfB(13),
                    dtmfC(14),
                    dtmfD(15),
                    busy(16),
                    confirmation(17),
                    dial(18),
                    messageWaiting(19),
                    offHookWarning(20),
                    ringBack(21),
                    reOrder(22),
                    stutterdial(23),
                    loopback(24),
                    callWaiting1(25),
                    callWaiting2(26),
                    callWaiting3(27),
                    callWaiting4(28),
                    alertingSignal(29),
                    testTone(30),
                    specialDial(31),
                    specialInfo(32),
                    release(33),
                    congestion(34),
                    userDefined1(35),
                    userDefined2(36),
                    userDefined3(37),
                    userDefined4(38)
                    busy(1),
                    confirmation(2),
                    dial(3),
                    messageWaiting(4),
                    offHookWarning(5),
                    ringBack(6),
                    reOrder(7),
                    stutterdial(8),
                    callWaiting1(9),
                    callWaiting2(10),
                    callWaiting3(11),
                    callWaiting4(12),
                    alertingSignal(13),
                    specialDial(14),
                    specialInfo(15),
                    release(16),
                    congestion(17),
                    userDefined1(18),
                    userDefined2(19),
                    userDefined3(20),

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

                    userDefined4(21)
                    }
       MAX-ACCESS   not-accessible
       STATUS       current
       DESCRIPTION

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
           " This object defines the type of tone being accessed. Note:
             the values The
             alertingSignal, specialDial, specialInfo, release,
             congestion and userDefined1-4 tone  types are enumerated starting at zero (e.g., dtmf0)
             to correspond to the digits on triggered
             using the telephone keypad." E line package."
       ::={pktcSigDevToneEntry 1 }

   pktcSigDevToneDbLevel    OBJECT-TYPE
       SYNTAX       Integer32 (-60..4)       TenthdBm (-600..40)
       UNITS        "dbm"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This is the decibel level for each frequency at which
             tones could be
             generated." generated at the a and b terminals (TE
             connection point)."
       DEFVAL { -4 -40 }
       ::={pktcSigDevToneEntry 2 }

   pktcSigDevToneFreqType    OBJECT-TYPE
       SYNTAX      INTEGER {
                   allFrequencies (1),
                   singleFrequencySequence (2),
                   dualFrequencySequence (3),
                   allFrequenciesModulated (4)
       }
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This object describes how the frequencies are applied.
             allFrequencies indicates all frequences specifed by
             pktcSigDevToneNumFrequencies are mixed to form a single
             tone. The tone is then applied in sequence using the
             number of on/off times specified in
             pktcSigDevToneNumOnOffTimes. SingleFrequecySequence
             indicates all frequencies specified by
             pktcSigDevToneNumFrequencies are applied in sequence
             using the corresponding frequency number on/off time
             (e.g., pktcSigDevToneFirstFrequency uses
             pktcSigDevToneFirstToneOn and pktcSigDevToneFirstToneOff,
             pktcSigDevToneSecondFrequency uses
             pktcSigDevToneSecondToneOn and
             pktcSigDevToneSecondToneOff). For this tone type
             pktcSigDevToneNumFrequencies MUST equal
             pktcSigDevToneNumOnOffTimes. DualFrequencySequence

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

             indicates two pairs of frequencies are mixed added to form two
             sequenced tones. The first and second frequency are mixed added
             to form tone one and are applied using
             pktcSigDevToneFirstToneOn and pktcSigDevToneFirstToneOff.
             The third and forth frequency are mixed added to form tone two
             and are applied using pktcSigDevToneSecondToneOn and
             pktcSigDevToneSecondToneOff. For this tone type

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
             pktcSigDevToneNumFrequencies MUST equal 4 and
             pktcSigDevToneNumOnOffTimes MUST equal 2.
             allFrequenciesModulated indicates all frequencies
             specified by pktcSigDevToneNumFrequencies are modulated to
             form a single tone. The tone is then applied in sequence
             using the number of on/off times specified in
             pktcSigDevToneNumOnOffTimes. For allFrequenciesModulated,
             the pktcSigDevToneNumFrequencies MUST equal 2, and the
             frequency in pktcSigDevToneFirstFrequency modulates the
             frequency in pktcSigDevToneSecondFrequency."
       REFERENCE
           "ITU-T E.180"
       DEFVAL { allFrequencies }
       ::={ pktcSigDevToneEntry 3 }

   pktcSigDevToneNumFrequencies    OBJECT-TYPE
       SYNTAX       Unsigned32 (1..4)
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " Specifies the number of frequencies specified in the table
             entry."
       DEFVAL { 1 }
       ::={pktcSigDevToneEntry 4}

   pktcSigDevToneFirstFrequency    OBJECT-TYPE
       SYNTAX       Unsigned32 (0..4000)
       UNITS        "Hertz"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This is the first frequency at which the tones could be
             generated in a multiple frequency tone."
       ::={pktcSigDevToneEntry 5}

   pktcSigDevToneSecondFrequency    OBJECT-TYPE
       SYNTAX       Unsigned32 (0..4000)
       UNITS        "Hertz"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This is the second frequency at which the tones could be

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

             generated in a multiple frequency tone."
       ::={pktcSigDevToneEntry 6}

   pktcSigDevToneThirdFrequency    OBJECT-TYPE
       SYNTAX       Unsigned32 (0..4000)
       UNITS        "Hertz"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
           " This is the third frequency at which the tones could be
             generated."
       ::={pktcSigDevToneEntry 7}

   pktcSigDevToneFourthFrequency    OBJECT-TYPE
       SYNTAX       Unsigned32 (0..4000)
       UNITS        "Hertz"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This is the fourth frequency at which the tones could be
             generated."
       ::={pktcSigDevToneEntry 8}

   pktcSigDevToneNumOnOffTimes    OBJECT-TYPE
       SYNTAX       Unsigned32 (1..4)
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " Specifies the number of on/off times specified in the
             table entry."
       DEFVAL { 1 }
       ::={pktcSigDevToneEntry 9}

   pktcSigDevToneFirstToneOn    OBJECT-TYPE
       SYNTAX       Unsigned32 (0..5000)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This is the first tone interval."
       ::={ pktcSigDevToneEntry 10}

   pktcSigDevToneFirstToneOff    OBJECT-TYPE
       SYNTAX       Unsigned32 (0..5000)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This is the first idle interval."

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

        ::={ pktcSigDevToneEntry 11 }

   pktcSigDevToneSecondToneOn    OBJECT-TYPE
       SYNTAX       Unsigned32 (0..5000)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This is the second tone interval."

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       ::={ pktcSigDevToneEntry 12 }

   pktcSigDevToneSecondToneOff    OBJECT-TYPE
       SYNTAX       Unsigned32 (0..5000)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This is the second idle interval."
       ::={ pktcSigDevToneEntry 13 }

   pktcSigDevToneThirdToneOn    OBJECT-TYPE
       SYNTAX       Unsigned32 (0..5000)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This is the third tone interval."
       ::={ pktcSigDevToneEntry 14 }

   pktcSigDevToneThirdToneOff    OBJECT-TYPE
       SYNTAX       Unsigned32 (0..5000)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This is the third idle interval."
       ::={ pktcSigDevToneEntry 15 }

   pktcSigDevToneFourthToneOn    OBJECT-TYPE
       SYNTAX       Unsigned32 (0..5000)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This is the fourth tone interval."
       ::={ pktcSigDevToneEntry 16 }

   pktcSigDevToneFourthToneOff    OBJECT-TYPE
       SYNTAX       Unsigned32 (0..5000)

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       UNITS        "Milliseconds"
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This is the Fourth idle interval."
       ::={ pktcSigDevToneEntry 17 }

   pktcSigDevToneWholeToneRepeatCount      OBJECT-TYPE
       SYNTAX       Unsigned32 (0..5000)

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This is the repeat count, which signifies how many times
             to repeat the entire on-off sequence."
       ::={ pktcSigDevToneEntry 18 }

   pktcSigDevToneSteady    OBJECT-TYPE
       SYNTAX       TruthValue
       MAX-ACCESS   read-write
       STATUS       current
       DESCRIPTION
           " This is the steady tone. Device must playout the on-off
             sequence for pktcSigDevToneWholeRepeatCount times and
             then apply the last tone forever."
       ::={ pktcSigDevToneEntry 19 }

   --
   -- The NCS End Point Config Table is used to define attributes that
   -- are specific to connection EndPoints.
   --

   pktcNcsEndPntConfigTable  OBJECT-TYPE
       SYNTAX        SEQUENCE OF PktcNcsEndPntConfigEntry
       MAX-ACCESS    not-accessible
       STATUS        current
       DESCRIPTION
           " This table describes the information pertaining to each
             endpoint of the MTA. All entries in this table represent
             the provisioned endpoints provisioned with the information
             required by the MTA to maintain the NCS signaling protocol
             communication with the CMS. Each endpoint can be assigned
             to a its own CMS. If the specific endpoint does not have
             the corresponding CMS information in this table, the
             endpoint is considered as not provisioned with voice
             services. Objects in this table do not persist across
             MTA reboots."
      ::=  { pktcNcsEndPntConfigObjects 1 }

   pktcNcsEndPntConfigEntry  OBJECT-TYPE

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       SYNTAX        PktcNcsEndPntConfigEntry
       MAX-ACCESS    not-accessible
       STATUS        current
       DESCRIPTION
           " Entries in pktcNcsEndPntConfigTable ű Each entry
             represents the required signaling parameters for the
             specific endpoint provisioned with voice services."
       INDEX { ifIndex }
       ::= { pktcNcsEndPntConfigTable 1 }

PacketCable/IPCablecom NCS Signaling MIB                  October 2003

   PktcNcsEndPntConfigEntry  ::= SEQUENCE {
       pktcNcsEndPntConfigCallAgentId             SnmpAdminString,
       pktcNcsEndPntConfigCallAgentUdpPort        InetPortNumber,
       pktcNcsEndPntConfigPartialDialTO           Unsigned32,
       pktcNcsEndPntConfigCriticalDialTO          Unsigned32,
       pktcNcsEndPntConfigBusyToneTO              Unsigned32,
       pktcNcsEndPntConfigDialToneTO              Unsigned32,
       pktcNcsEndPntConfigMessageWaitingTO        Unsigned32,
       pktcNcsEndPntConfigOffHookWarnToneTO       Unsigned32,
       pktcNcsEndPntConfigRingingTO               Unsigned32,
       pktcNcsEndPntConfigRingBackTO              Unsigned32,
       pktcNcsEndPntConfigReorderToneTO           Unsigned32,
       pktcNcsEndPntConfigStutterDialToneTO       Unsigned32,
       pktcNcsEndPntConfigTSMax                   Unsigned32,
       pktcNcsEndPntConfigMax1                    Unsigned32,
       pktcNcsEndPntConfigMax2                    Unsigned32,
       pktcNcsEndPntConfigMax1QEnable             TruthValue,
       pktcNcsEndPntConfigMax2QEnable             TruthValue,
       pktcNcsEndPntConfigMWD                     Unsigned32,
       pktcNcsEndPntConfigTdinit                  Unsigned32,
       pktcNcsEndPntConfigTdmin                   Unsigned32,
       pktcNcsEndPntConfigTdmax                   Unsigned32,
       pktcNcsEndPntConfigRtoMax                  Unsigned32,
       pktcNcsEndPntConfigRtoInit                 Unsigned32,
       pktcNcsEndPntConfigLongDurationKeepAlive   Unsigned32,
       pktcNcsEndPntConfigThist                   Unsigned32,
       pktcNcsEndPntConfigStatus                  RowStatus,
       pktcNcsEndPntConfigCallWaitingMaxRep       Unsigned32,
       pktcNcsEndPntConfigCallWaitingDelay        Unsigned32,
       pktcNcsEndPntStatusCallIpAddressType       InetAddressType,
       pktcNcsEndPntStatusCallIpAddress           InetAddress,
       pktcNcsEndPntStatusError                   INTEGER,
       pktcNcsEndPntConfigMinHookFlash            Unsigned32,
       pktcNcsEndPntConfigMaxHookFlash            Unsigned32,
       pktcNcsEndPntConfigPulseDialInterdigitTime Unsigned32,
       pktcNcsEndPntConfigPulseDialMinMakeTime    Unsigned32,
       pktcNcsEndPntConfigPulseDialMaxMakeTime    Unsigned32,
       pktcNcsEndPntConfigPulseDialMinBreakTime   Unsigned32,
       pktcNcsEndPntConfigPulseDialMaxBreakTime   Unsigned32

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       }

   pktcNcsEndPntConfigCallAgentId     OBJECT-TYPE
       SYNTAX      SnmpAdminString(SIZE (3..255))
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           " This object contains a string indicating the call agent
             name. (e.g.,: ca@example.com). The call agent name after

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
             the @ character must be a fully qualified domain name and
             have a corresponding pktcMtaDevCmsFqdn entry in the
             pktcMtaDevCmsTable. The object pktcMtaDevCmsFqdn is
             defined in the PacketCable MIBMTA Specification."
       ::= {  pktcNcsEndPntConfigEntry 1 }

   pktcNcsEndPntConfigCallAgentUdpPort    OBJECT-TYPE
       SYNTAX      InetPortNumber (1025..65535)
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           " This object contains the call agent User Datagram Protocol
             (UDP) receive port that is being used for this instance of
             call signaling, i.e. the default port on which the call
             agent will receive NCS signaling from the endpoint."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL    { 2727 }
       ::= { pktcNcsEndPntConfigEntry 2 }

   pktcNcsEndPntConfigPartialDialTO     OBJECT-TYPE
       SYNTAX       Unsigned32
       UNITS        "seconds"
       MAX-ACCESS   read-create
       STATUS       current
       DESCRIPTION
           " This object contains maximum value of the partial dial
             time out."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL { 16 }
       ::= { pktcNcsEndPntConfigEntry 3 }

   pktcNcsEndPntConfigCriticalDialTO     OBJECT-TYPE
       SYNTAX       Unsigned32
       UNITS        "seconds"
       MAX-ACCESS   read-create
       STATUS       current
       DESCRIPTION
           " This object contains the maximum value of the critical

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

             dial time out."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL { 4 }
       ::= { pktcNcsEndPntConfigEntry 4 }

   pktcNcsEndPntConfigBusyToneTO     OBJECT-TYPE
       SYNTAX       Unsigned32
       UNITS        "seconds"

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       MAX-ACCESS   read-create
       STATUS       current
       DESCRIPTION
           " This object contains the timeout value for busy tone."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL    { 30 }
       ::= { pktcNcsEndPntConfigEntry 5 }

   pktcNcsEndPntConfigDialToneTO     OBJECT-TYPE
       SYNTAX       Unsigned32
       UNITS        "seconds"
       MAX-ACCESS   read-create
       STATUS       current
       DESCRIPTION
           " This object contains the timeout value for dial tone."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL    { 16 }
       ::= { pktcNcsEndPntConfigEntry 6 }

   pktcNcsEndPntConfigMessageWaitingTO     OBJECT-TYPE
       SYNTAX       Unsigned32
       UNITS        "seconds"
       MAX-ACCESS   read-create
       STATUS       current
       DESCRIPTION
           " This object contains the timeout value for message waiting
             indicator."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL    { 16 }
       ::= { pktcNcsEndPntConfigEntry 7 }

   pktcNcsEndPntConfigOffHookWarnToneTO     OBJECT-TYPE
       SYNTAX       Unsigned32
       UNITS        "seconds"
       MAX-ACCESS   read-create
       STATUS       current
       DESCRIPTION

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

           " This object contains timeout value for off hook Warning
             tone."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL { 0 }
       ::= { pktcNcsEndPntConfigEntry 8 }

   pktcNcsEndPntConfigRingingTO     OBJECT-TYPE
       SYNTAX       Unsigned32

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       UNITS        "seconds"
       MAX-ACCESS   read-create
       STATUS       current
       DESCRIPTION
           " This object contains the timeout value for ringing."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL    { 180 }
       ::= { pktcNcsEndPntConfigEntry 9 }

   pktcNcsEndPntConfigRingBackTO     OBJECT-TYPE
       SYNTAX       Unsigned32
       UNITS        "seconds"
       MAX-ACCESS   read-create
       STATUS       current
       DESCRIPTION
           " This object contains the timeout value for ring back."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL    { 180 }
       ::= { pktcNcsEndPntConfigEntry 10 }

   pktcNcsEndPntConfigReorderToneTO     OBJECT-TYPE
       SYNTAX       Unsigned32
       UNITS        "seconds"
       MAX-ACCESS   read-create
       STATUS       current
       DESCRIPTION
           " This object contains the timeout value for reorder tone."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL    { 30 }
       ::= { pktcNcsEndPntConfigEntry 11 }

   pktcNcsEndPntConfigStutterDialToneTO     OBJECT-TYPE
       SYNTAX       Unsigned32
       UNITS        "seconds"
       MAX-ACCESS   read-create
       STATUS       current
       DESCRIPTION

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

           " This object contains timeout value for stutter dial tone."
       REFERENCE
             "PacketCable NCS Specification"
       DEFVAL    { 16 }
       ::= { pktcNcsEndPntConfigEntry 12 }

   pktcNcsEndPntConfigTSMax     OBJECT-TYPE
       SYNTAX      Unsigned32
       MAX-ACCESS  read-create

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       STATUS      current
       DESCRIPTION
           " This object contains the max time in seconds since the
             sending of the initial datagram."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL { 20 }
       ::= { pktcNcsEndPntConfigEntry 13 }

   pktcNcsEndPntConfigMax1     OBJECT-TYPE
       SYNTAX      Unsigned32
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           " This object contains the suspicious error threshold for
             signaling messages."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL { 5 }
       ::= { pktcNcsEndPntConfigEntry 14 }

   pktcNcsEndPntConfigMax2     OBJECT-TYPE
       SYNTAX      Unsigned32
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           " This object contains the disconnect error threshold for
             signaling messages."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL { 7 }
       ::= { pktcNcsEndPntConfigEntry 15 }

   pktcNcsEndPntConfigMax1QEnable     OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           " This object enables/disables the Max1 Domain Name Server
             (DNS) query operation when Max1 expires."

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       DEFVAL { true }
       ::= { pktcNcsEndPntConfigEntry 16 }

   pktcNcsEndPntConfigMax2QEnable     OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           " This object enables/disables the Max2 DNS query operation

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
             when Max2 expires."
       DEFVAL { true }
       ::= { pktcNcsEndPntConfigEntry 17 }

   pktcNcsEndPntConfigMWD     OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "seconds"
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           " Maximum Waiting Delay (MWD) contains the maximum number of
             seconds a MTA waits after a restart. When this timer
             expires the MTA initiates the restart procedure."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL { 600 }
       ::= { pktcNcsEndPntConfigEntry 18 }

   pktcNcsEndPntConfigTdinit     OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "seconds"
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           " This object contains the initial number of seconds the MTA
             waits after a disconnect. When this timer expires the MTA
             initiates the disconnected procedure."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL { 15 }
       ::= { pktcNcsEndPntConfigEntry 19 }

   pktcNcsEndPntConfigTdmin     OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "seconds"
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           " This object contains the minimum number of seconds the MTA
             waits after a disconnect. When this timer expires the MTA

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

             initiates the disconnected procedure."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL { 15 }
       ::= { pktcNcsEndPntConfigEntry 20 }

   pktcNcsEndPntConfigTdmax     OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "seconds"

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           " This object contains the maximum number of seconds the MTA
             waits after a disconnect. When this timer expires the MTA
             initiates the disconnected procedure.
              "
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL { 600 }
       ::= { pktcNcsEndPntConfigEntry 21 }

   pktcNcsEndPntConfigRtoMax     OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "seconds"
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           " This object contains the maximum number of seconds for the
             retransmission timer. When this timer expires the MTA
             retransmits the message."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL { 4 }
       ::= { pktcNcsEndPntConfigEntry 22 }

   pktcNcsEndPntConfigRtoInit     OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "milliseconds"
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           " This object contains the initial number of seconds for the
             retransmission timer."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL { 200 }
       ::= { pktcNcsEndPntConfigEntry 23 }

   pktcNcsEndPntConfigLongDurationKeepAlive     OBJECT-TYPE

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       SYNTAX      Unsigned32
       UNITS       "minutes"
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           " Specifies a timeout value in minutes for sending long
             duration call notification message."
       REFERENCE
           "PacketCable NCS Specification"

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       DEFVAL { 60 }
       ::= { pktcNcsEndPntConfigEntry 24 }

   pktcNcsEndPntConfigThist  OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "seconds"
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           " Timeout period in seconds before no response is declared."
       REFERENCE
           "PacketCable NCS Specification"
       DEFVAL { 30 }
       ::= { pktcNcsEndPntConfigEntry 25 }

   pktcNcsEndPntConfigStatus     OBJECT-TYPE
       SYNTAX      RowStatus
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           " This object contains the Row Status associated with the
             pktsNcsEndPntTable. "
       ::= { pktcNcsEndPntConfigEntry 26 }

   pktcNcsEndPntConfigCallWaitingMaxRep     OBJECT-TYPE
       SYNTAX      Unsigned32 (0..10)
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           " This object contains the maximum number of repetitions
             of the call waiting tone that the MTA will play from a
             single CMS request.  A value of zero (0) can be used if
             the CMS is to control the repetitions of the call waiting
             tone."
       DEFVAL    { 1 }
       ::= { pktcNcsEndPntConfigEntry 27 }

   pktcNcsEndPntConfigCallWaitingDelay     OBJECT-TYPE
       SYNTAX       Unsigned32 (1..100)
       UNITS        "seconds"

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       MAX-ACCESS   read-create
       STATUS       current
       DESCRIPTION
           " This object contains the delay between repetitions of the
             call waiting tone that the MTA will play from a single CMS
             request."
       DEFVAL    { 10 }
       ::= { pktcNcsEndPntConfigEntry 28 }

PacketCable/IPCablecom NCS Signaling MIB                  October 2003

   pktcNcsEndPntStatusCallIpAddressType  OBJECT-TYPE
       SYNTAX      InetAddressType
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          " This object contains the type of Internet address of the
            CMS currently being used for this endpoint."
       ::= { pktcNcsEndPntConfigEntry 29 }

   pktcNcsEndPntStatusCallIpAddress  OBJECT-TYPE
       SYNTAX      InetAddress
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
          " This object contains the Internet address of the CMS
            currently being used for this endpoint. This Internet
            address is used to create the appropriate security
            association. The type of this IP address is determined by
            the value of the pktcNcsEndPntStatusCallIpAddressType
            object."
   ::= { pktcNcsEndPntConfigEntry 30 }

   pktcNcsEndPntStatusError  OBJECT-TYPE
       SYNTAX INTEGER {
                  operational (1),
                  noSecurityAssociation (2),
                  disconnected (3)
                }
       MAX-ACCESS   read-only
       STATUS  current
       DESCRIPTION
          " This object contains the error status for this interface.
            The operational status indicates that all operations
            necessary to put the line in service have occurred, and the
            CMS has acknowledged the RSIP message successfully. If
            pktcMtaDevCmsIpsecCtrl is enabled for the associated Call
            Agent, the noSecurityAssociation status indicates that no
            Security Association (SA) yet exists for this endpoint.
            Otherwise, the state is unused. The disconnected status
            indicates one of the following two:

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

            If pktcMtaDevCmsIpsecCtrl is disabled, then no security
            association is involved with this endpoint. The NCS
            signaling software is in process of establishing the NCS
            signaling link via an RSIP exchange.
            Otherwise, pktcMtaDevCmsIpsecCtrl is enabled, the security
            Association has been established, and the NCS signaling
            software is in process of establishing the NCS signaling
            link via an RSIP exchange."
       ::= { pktcNcsEndPntConfigEntry 31 }

PacketCable/IPCablecom NCS Signaling MIB                  October 2003

   pktcNcsEndPntConfigMinHookFlash    OBJECT-TYPE
       SYNTAX       Unsigned32 (20..1000)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
           " This is the minimum time a line needs to be on hook for a
             valid hook flash. The value of this object MUST be
             greater than the value of
             pktcNcsEndPntConfigPulseMaxBreakTime. This object must
             only be set via the configuration file during the
             provisioning process."
       DEFVAL { 300 }
       ::= { pktcNcsEndPntConfigEntry 32 }

   pktcNcsEndPntConfigMaxHookFlash    OBJECT-TYPE
       SYNTAX       Unsigned32 (20..500)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
           " This is the maximum time a line needs to be on hook for a
             valid hook flash. This object must only be set via the
             configuration file during the provisioning process."
       DEFVAL { 500 }
       ::= { pktcNcsEndPntConfigEntry 33 }

   pktcNcsEndPntConfigPulseDialInterdigitTime    OBJECT-TYPE
       SYNTAX       Unsigned32 (100..1500)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
           " This is the pulse dial inter-digit timeout. This object
             must only be set via the configuration file during the
             provisioning process."
       DEFVAL { 100 }
       ::= { pktcNcsEndPntConfigEntry 34 }

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

   pktcNcsEndPntConfigPulseDialMinMakeTime    OBJECT-TYPE
       SYNTAX       Unsigned32 (20..200)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
           " This is the minimum make pulse width for the dial pulse.
             This object must only be set via the configuration file
             during the provisioning process."

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       DEFVAL { 25 }
       ::= { pktcNcsEndPntConfigEntry 35 }

   pktcNcsEndPntConfigPulseDialMaxMakeTime    OBJECT-TYPE
       SYNTAX       Unsigned32 (20..200)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
           " This is the maximum make pulse width for the dial pulse.
             This object must only be set via the configuration file
             during the provisioning process."
       DEFVAL { 55 }
       ::= { pktcNcsEndPntConfigEntry 36 }

   pktcNcsEndPntConfigPulseDialMinBreakTime    OBJECT-TYPE
       SYNTAX       Unsigned32 (20..200)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
           " This is the minimum break pulse width for the dial pulse.
             This object must only be set via the configuration file
             during the provisioning process."
       DEFVAL { 45 }
       ::= { pktcNcsEndPntConfigEntry 37 }

   pktcNcsEndPntConfigPulseDialMaxBreakTime    OBJECT-TYPE
       SYNTAX       Unsigned32 (20..200)
       UNITS        "Milliseconds"
       MAX-ACCESS   read-only
       STATUS       current
       DESCRIPTION
           " This is the maximum break pulse width for the dial pulse.
             This object must only be set via the configuration file
             during the provisioning process."
       DEFVAL { 75 }
       ::= { pktcNcsEndPntConfigEntry 38 }

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

   --
   -- notification group is for future extension.
   --
   pktcSigNotification  OBJECT IDENTIFIER ::= { pktcSigMib 0 }
   pktcSigConformance   OBJECT IDENTIFIER ::= { pktcSigMib 3 }
   pktcSigCompliances   OBJECT IDENTIFIER ::= { pktcSigConformance 1 }
   pktcSigGroups        OBJECT IDENTIFIER ::= { pktcSigConformance 2 }

   --
   -- compliance statements

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
   --

   pktcSigBasicCompliance  MODULE-COMPLIANCE
       STATUS     current
       DESCRIPTION
           " The compliance statement for devices that implement
             Signaling on the MTA."

   MODULE  -- pktcSigMib

   --
   --  unconditionally mandatory groups
   --

   MANDATORY-GROUPS {
       pktcSigGroup
   }

   GROUP pktcNcsGroup
       DESCRIPTION
           " This group is mandatory for any MTA implementing NCS
             signaling"

   GROUP pktcInternationalGroup
       DESCRIPTION
           " This group is mandatory for any MTA implementing
             international telephony features. In such cases, it is
             left to manufacturers to determine whether to support both
             PacketCable and IPCablecom objects in the same MTA."
       ::={ pktcSigCompliances 1 }

   --
   -- units of conformance
   --

   pktcSigGroup  OBJECT-GROUP
       OBJECTS {
       pktcSigDevCodecType,
       pktcSigDevCodecMax,

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       pktcSigDevEchoCancellation,
       pktcSigDevSilenceSuppression,
       pktcSigDevR0Cadence,
       pktcSigDevR6Cadence,
       pktcSigDevR7Cadence,
       pktcSigDefCallSigDscp,
       pktcSigDefMediaStreamDscp,
       pktcSigDevVmwiMode,
       pktcSignalingType,
       pktcSignalingVersion,
       pktcSignalingVendorExtension,

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       pktcSigDefNcsReceiveUdpPort,
       pktcSigServiceClassNameUS,
       pktcSigServiceClassNameDS,
       pktcSigServiceClassNameMask,
       pktcSigNcsServiceFlowState,
       pktcSigDevR1Cadence,
       pktcSigDevR2Cadence,
       pktcSigDevR3Cadence,
       pktcSigDevR4Cadence,
       pktcSigDevR5Cadence,
       pktcSigDevRgCadence,
       pktcSigDevRsCadence,
       pktcSigDevRtCadence
       pktcSigDevRsCadence

       }
       STATUS current
       DESCRIPTION
             "Group of objects for the common portion of the
              PacketCable Signaling MIB."
       ::= { pktcSigGroups 1 }

   pktcNcsGroup  OBJECT-GROUP
       OBJECTS {
       pktcNcsEndPntConfigCallAgentId,
       pktcNcsEndPntConfigCallAgentUdpPort,
       pktcNcsEndPntConfigPartialDialTO,
       pktcNcsEndPntConfigCriticalDialTO,
       pktcNcsEndPntConfigBusyToneTO,
       pktcNcsEndPntConfigDialToneTO,
       pktcNcsEndPntConfigMessageWaitingTO,
       pktcNcsEndPntConfigOffHookWarnToneTO,
       pktcNcsEndPntConfigRingingTO,
       pktcNcsEndPntConfigRingBackTO,
       pktcNcsEndPntConfigReorderToneTO,
       pktcNcsEndPntConfigStutterDialToneTO,
       pktcNcsEndPntConfigTSMax,
       pktcNcsEndPntConfigMax1,
       pktcNcsEndPntConfigMax2,
       pktcNcsEndPntConfigMax1QEnable,

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       pktcNcsEndPntConfigMax2QEnable,
       pktcNcsEndPntConfigMWD,
       pktcNcsEndPntConfigTdinit,
       pktcNcsEndPntConfigTdmin,
       pktcNcsEndPntConfigTdmax,
       pktcNcsEndPntConfigRtoMax,
       pktcNcsEndPntConfigRtoInit,
       pktcNcsEndPntConfigLongDurationKeepAlive,
       pktcNcsEndPntConfigThist,
       pktcNcsEndPntConfigStatus,
       pktcNcsEndPntConfigCallWaitingMaxRep,

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       pktcNcsEndPntConfigCallWaitingDelay,
       pktcNcsEndPntStatusCallIpAddressType,
       pktcNcsEndPntStatusCallIpAddress,
       pktcNcsEndPntStatusError
       }
       STATUS current
       DESCRIPTION
             "Group of objects for the NCS portion of the PacketCable
              Signaling MIB. This is mandatory for NCS signaling."
       ::= { pktcSigGroups 2 }

   pktcInternationalGroup    OBJECT-GROUP
       OBJECTS {
       pktcNcsEndPntConfigMinHookFlash,
       pktcNcsEndPntConfigMaxHookFlash,
       pktcNcsEndPntConfigPulseDialInterdigitTime,
       pktcNcsEndPntConfigPulseDialMinMakeTime,
       pktcNcsEndPntConfigPulseDialMaxMakeTime,
       pktcNcsEndPntConfigPulseDialMinBreakTime,
       pktcNcsEndPntConfigPulseDialMaxBreakTime,
       pktcSigDevRingCadence,
       pktcSigDevStandardRingCadence,
       pktcSigDevRingSplashCadence,
       pktcSigDevCallerIdSigProtocol,
       pktcSigDevCIDMode,
       pktcSigDevCIDFskAfterRing,
       pktcSigDevCIDFskAfterDTAS,
       pktcSigDevCIDFskAfterRPAS,
       pktcSigDevCIDRingAfterFSK,
       pktcSigDevCIDDTASAfterLR,
       pktcSigDevVmwiMode,
       pktcSigDevVmwiFskAfterDTAS,
       pktcSigDevVmwiFskAfterRPAS,
       pktcSigDevVmwiDTASAfterLR,
       pktcSigPowerRingFrequency,
       pktcSigPulseSignalDuration,
       pktcSigPulseSignalType,
       pktcSigPulseSignalDbLevel,
       pktcSigPulseSignalFrequency,
       pktcSigPulseSignalDbLevel,
       pktcSigPulseSignalDuration,

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       pktcPulseSignalPulseInterval,
       pktcSigPulseSignalRepeatCount,
       pktcSigPulseSignalPauseDuration,
       pktcSigDevToneDbLevel,
       pktcSigDevToneFreqType,
       pktcSigDevToneNumFrequencies,
       pktcSigDevToneFirstFrequency,
       pktcSigDevToneSecondFrequency,
       pktcSigDevToneThirdFrequency,
       pktcSigDevToneFourthFrequency,
       pktcSigDevToneNumOnOffTimes,

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       pktcSigDevToneFirstToneOn,
       pktcSigDevToneFirstToneOff,
       pktcSigDevToneSecondToneOn,
       pktcSigDevToneSecondToneOff,
       pktcSigDevToneThirdToneOn,
       pktcSigDevToneThirdToneOff,
       pktcSigDevToneFourthToneOn,
       pktcSigDevToneFourthToneOff,
       pktcSigDevToneWholeToneRepeatCount,
       pktcSigDevToneSteady
       }
       STATUS current
       DESCRIPTION
           " Group of objects that extend the behavior of existing
             objects to support operations in the widest possible set
             of international marketplaces.  Note that many of these
             objects represent a superset of behaviors described in
             other objects within this MIB Module."
       ::= { pktcSigGroups 3 }

   END

5. Acknowledgments

   This document is a production of the PacketCable Working Group.

   The current editors wish to express gratitude to:

       Angela Lyda           Arris Interactive
       Sasha Medvinsky       Motorola
       Roy Spitzer           Telogy Networks, Inc.
       Rick Vetter           Motorola
       Itay Sherman          Texas Instruments
       Klaus Hermanns        Cisco Systems
       Eugene Nechamkin      Broadcom Corp
       Matt A. Osman         CableLabs
       Jean-Francois Mule    CableLabs
       Rich Woundy           Comcast
       Bert Wijnen           Lucent

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

       Mike Heard            Consultant

6. Normative References

   [RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
             Rose, M. and S. Waldbusser, "Structure of Management
             Information Version 2 (SMIv2)", STD 58, RFC 2578, April
             1999.

   [RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
             Rose, M. and S. Waldbusser, "Textual Conventions for
             SMIv2", STD 58, RFC 2579, April 1999.

   [RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
             Rose, M. and S. Waldbusser, "Conformance Statements for
             SMIv2", STD 58, RFC 2580, April 1999.

   [RFC3289] Baker, F., Chan, K., Smith, A., "Management Information
             Base for the Differentiated Services Architecture", RFC
             3289, May 2002.

   [RFC3291] Daniel, M., Haberman, B., Routhier, S., Schoenwaelder, J.,
             "Textual Conventions for Internet Network Addresses", RFC
             3291, May 2002.

   --
   -- NOTES TO RFC EDITOR (to be removed prior to publication)
   --
   -- The I-D <draft-ietf-ops-rfc3291bis-01.txt> (or a successor) is
   -- expected to eventually replace RFC 3291. If that draft (or a
   -- successor) is published as an RFC prior to, or concurrently with
   -- this document, then the normative reference [RFC3291] should be
   -- updated to point to the replacement RFC, and the reference tag
   -- [RFC3291] should be updated to match.
   --

   [PKT-SP-MGCP-IO7-030415]

   [PKT-SP-MGCP-IO9-040113] Packetcable Network-Based Call Signaling
                            Protocol Specification PKT-SP-EC-MGCP-
                               IO7-030415.

   [PKT-SP-PROV-IO6-030415]
                            IO9-040113.

   [PKT-SP-PROV-IO8-040113] Packetcable MTA Device Provisioning
                            Specification PKT-SP-PROV-IO6-030415.

   [PKT-SP-CODEC-IO4-021018] PKT-SP-PROV-IO8-040113.

   [PKT-SP-CODEC-IO5-040113] Packetcable Audio/Video Codecs
                             Specification PKT-SP-CODEC-IO4-021018. PKT-SP-CODEC-IO5-040113.

7. Informative References

   [RFC3261] Rosenberg, J., Schulzrinne H., Camarillo, G., Johnston,

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

             A., Peterson, J., Sparks, R., Handley, M., and Schooler,
             E. "SIP: Session Initiation Protocol", RFC 3261, June
             2002.

   [RFC3410] Case, J., Mundy, R., Partain, D. and B. Stewart,
             "Introduction and Applicability Statements for Internet-
             Standard Management Framework", RFC 3410, December 2002.

   [RFC3435] Andreasen, F., Foster, B., "Media Gateway Control Protocol
             (MGCP)", RFC 3435, January 2003.

PacketCable/IPCablecom NCS Signaling MIB                  October 2003

   [PKT-SP-MIB-MTA-I07-030728]

   [PKT-SP-MIB-MTA-I08-040113] Packetcable MTA MIB Specification PKT-
                               SP-MIB-MTA-I07-030728.
                               SP-MIB-MTA-I08-040113.

   [ETSI TS 101 909-4] ETSI TS 101 909-4:"Access and Terminals (AT);
                       Digital Broadband Cable Access to the Public
                       Telecommunications Network; IP Multimedia Time
                       Critical Services; Part 4: Network Call
                       Signaling Protocol".

   [ETSI TS 101 909-9] ETSI TS 101 909-9:"Access and Terminals (AT);
                       Digital Broadband Cable Access to the Public
                       Telecommunications Network; IP Multimedia Time
                       Critical Services; Part 9: IPCablecom Network
                       Call Signalling (NCS) MIB Requirements".

   [EN 300 001] EN 300 001 V1.5.1 (1998-10):"European Standard
                (Telecommunications series) Attachments to Public
                Switched Telephone Network (PSTN); General technical
                requirements for equipment connected to an analogue
                subscriber interface in the PSTN; Chapter 3: Ringing
                signal characteristics (national deviations are in
                Table 3.1.1)".

   [EN 300 324-1] EN 300 324-1 V2.1.1 (2000-04):"V Interfaces at the
                  digital Loop Exchange (LE); V5.1 interface for the
                  support of Access Network (AN); Part 1: V5.1
                  interface specification".

   [EN 300 659-1] EN 300 659-1: ˘Public "Public Switched Telephone Network
                  (PSTN); Subscriber line protocol over the local loop
                  for display (and related) services; Part 1: On hook
                  data transmission÷. transmission".

   [ITU-T E.180] ITU-T: "Various Tones Used in National Networks,
                 Supplement 2 to Recommendation E.180".

   [TR 101 183] TR 101 183: "Public Switched Telephone Network (PSTN)
                Analogue Ringing Signals".

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

8. Security Considerations

   There are a number of management objects defined in this MIB that
   have a MAX-ACCESS clause of read-write and/or read-create. Such
   objects may be considered sensitive or vulnerable in some network
   environments. The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on
   network operations.

   The following Differentiated Services Code Point (DSCP) and mask
   objects are used to differentiate between various types of traffic
   in the service provider network:

        pktcSigDefCallSigDscp
        pktcSigDefMediaStreamDscp
        pktcSigServiceClassNameMask

   These objects may contain information that may be sensitive from a
   business perspective. For example, they may represent a customer's
   service contract that a service provider chooses to apply to a

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
   customer's ingress or egress traffic. If these objects are SET
   maliciously, it may permit unmarked or inappropriately marked
   signaling and media traffic to enter the service provider network,
   resulting in unauthorized levels of service for customers.

   The following objects determine ring cadence, repeatable
   characteristics, signal duration, and caller id subscriber line
   protocol for telephony operation:

        pktcSigDevR0Cadence
        pktcSigDevR1Cadence
        pktcSigDevR2Cadence
        pktcSigDevR3Cadence
        pktcSigDevR4Cadence
        pktcSigDevR5Cadence
        pktcSigDevR6Cadence
        pktcSigDevR7Cadence
        pktcSigDevRgCadence
        pktcSigDevRsCadence
        pktcSigDevRtCadence
        pktcSigDevCallerIdSigProtocol
        pktcSigPulseSignalDuration
        pktcSigPulseSignalPauseDuration

   If these objects are SET maliciously, it may result in unwanted
   operation, or a failure to obtain telephony service from client
   (MTA) devices.

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

   The objects in the pktcNcsEndPntConfigTable are used for end point
   signaling. The pktcNcsEndPntConfigCallAgentId object contains the
   name of the call agent, which includes the call agent FQDN. If this
   object is SET maliciously, the MTA will not be able to communicate
   with the call agent, resulting in a disruption of telephony service.
   The pktcNcsEndPntConfigCallAgentUdpPort object identifies the UDP
   port for NCS signaling traffic. If this object is SET maliciously,
   the call agent will not receive NCS signaling traffic from the MTA,
   also resulting in a disruption of telephony service.

   Some of the readable objects in this MIB module (i.e., objects with
   a MAX-ACCESS other than not-accessible) may be considered sensitive
   or vulnerable in some network environments.  It is thus important to
   control even GET and/or NOTIFY access to these objects and possibly
   to even encrypt the values of these objects when sending them over
   the network via SNMP.  The most sensitive is
   pktcNcsEndPntStatusCallIpAddress within pktcNcsEndPntConfigTable.
   This information itself may be valuable to would-be attackers.

   SNMP versions prior to SNMPv3 did not include adequate security.
   Even if the network itself is secure (for example by using IPSec),

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
   even then, there is no control as to who on the secure network is
   allowed to access and GET/SET (read/change/create/delete) the
   objects in this MIB module.

   It is RECOMMENDED that implementers consider the security features
   as provided by the SNMPv3 framework (see [RFC3410], section 8),
   including full support for the SNMPv3 cryptographic mechanisms (for
   authentication and privacy).

   Further, deployment of SNMP versions prior to SNMPv3 is NOT
   RECOMMENDED.  Instead, it is RECOMMENDED to deploy SNMPv3 and to
   enable cryptographic security.  It is then a customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of this MIB module is properly configured to give access to
   the objects only to those principals (users) that have legitimate
   rights to indeed GET or SET (change/create/delete) them.

9. Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   intellectual property or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; neither does it represent that it
   has made any effort to identify any such rights. Information on the
   IETF's procedures with respect to rights in standards-track and
   standards-related documentation can be found in BCP-11. Copies of
   claims of rights made available for publication and any assurances

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

   of licenses to be made available, or the result of an attempt made
   to obtain a general license or permission for the use of such
   proprietary rights by implementers or users of this specification
   can be obtained from the IETF Secretariat.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights which may cover technology that may be required to practice
   this standard.  Please address the information to the IETF Executive
   Director.

10. Authors' Addresses

       Gordon Beacham
       Motorola BCS/DCG
       6450 Sequence Drive, Bldg. 1
       San Diego, CA 92121, USA
       +1 858-404-2335
       gordon.beacham@motorola.com

       Satish Kumar Mudugere Eswaraiah

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
       Texas Instruments India (P) Ltd.,
       Golf view, Wind Tunnel Road
       Murugesh Palya
       Bangalore - 560 017, INDIA
       +91 80 5269451
       satish.kumar@ti.com

       Sumanth Channabasappa
       Alopa Networks Inc
       248, McCaslin Bvld #101,
       Louisville, Colorado - 80027
       U.S.A.
       +1 303 604 6595
       Sumanth@alopa.com

11. Full Copyright Statement

   The IETF takes no position regarding the validity or scope of any
   intellectual property or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; neither does it represent that it
   has made any effort to identify any such rights. Information on the
   IETF's procedures with respect to rights in standards-track and
   standards-related documentation can be found in BCP-11. Copies of
   claims of rights made available for publication and any assurances
   of licenses to be made available, or the result of an attempt made
   to obtain a general license or permission for the use of such

PacketCable/IPCablecom NCS Signaling MIB                 February 2004

   proprietary rights by implementers or users of this specification
   can be obtained from the IETF Secretariat.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights which may cover technology that may be required to practice
   this standard. Please address the information to the IETF Executive
   Director.

   Copyright (C) The Internet Society (2003). (2004). All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implmentation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph
   are included on all such copies and derivative works. However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for

PacketCable/IPCablecom NCS Signaling MIB                  October 2003
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.