draft-ietf-ippm-reporting-mib-04.txt		draft-ietf-ippm-reporting-mib-05.txt
	Network Working Group E. Stephan/J. Jewitt		Network Working Group E. Stephan/J. Jewitt
	Internet Draft France Telecom R&D		Internet Draft France Telecom R&D
	Document: draft-ietf-ippm-reporting-mib-04.txt October, 2003		Document: draft-ietf-ippm-reporting-mib-05.txt February, 2004
	Category: Informational		Category: Standards Track
	IPPM reporting MIB		IPPM reporting MIB
	Status of this Memo		Status of this Memo
	This document is an Internet-Draft and is in full conformance with		This document is an Internet-Draft and is in full conformance with
	all provisions of Section 10 of RFC2026 [1].		all provisions of Section 10 of RFC2026 [1].
	Internet-Drafts are working documents of the Internet Engineering		Internet-Drafts are working documents of the Internet Engineering
	Task Force (IETF), its areas, and its working groups. Note that other		Task Force (IETF), its areas, and its working groups. Note that other
	skipping to change at page 2, line 11		skipping to change at page 2, line 11
	In particular, this MIB specifies the objects used for managing the		In particular, this MIB specifies the objects used for managing the
	results of the IPPM metrics measures, for pushing alarms, and for		results of the IPPM metrics measures, for pushing alarms, and for
	reporting the measures results.		reporting the measures results.
	Table of Contents		Table of Contents
	1. Introduction................................................2		1. Introduction................................................2
	2. The IPPM Framework..........................................3		2. The IPPM Framework..........................................3
	3. The SNMP Management Framework...............................3		3. The SNMP Management Framework...............................3
	4. Overview....................................................5		4. Overview....................................................5
	4.1. Textual Conventions.........................................6		4.1. Textual Conventions.........................................5
	4.2 Structure of the MIB.........................................8		4.2 Structure of the MIB.........................................8
	4.3 Row identification in an application namespace..............10		4.3 Row identification in an application namespace..............10
	4.4 Relationship of IPPM REPORTING MIB tables...................11		4.4 Relationship of IPPM REPORTING MIB tables...................11
	5 Measurement architectures...................................12		5 Measurement architectures...................................12
	5.1 Proxy architecture..........................................12		5.1 Proxy architecture..........................................12
	5.2 Reporting architecture......................................13		5.2 Reporting architecture......................................13
	5.3 Gateway architecture........................................15		5.3 Gateway architecture........................................15
	5.4 Security....................................................15		5.4 Security....................................................15
	6 Reporting mode integration..................................16		6 Reporting mode integration..................................16
	6.1 Integration.................................................16		6.1 Integration.................................................16
	6.2 Setup of the measure network................................16		6.2 Setup of the network measure table..........................16
	6.3 Setup of a measurement report...............................16		6.3 Setup of the aggregated measure table.......................16
	6.4 Updating the history of the MIB.............................17		6.4 Updating the history of the MIB.............................17
	6.5 Report download and upload..................................17		6.5 Default value...............................................17
	6.6 Default value...............................................17
	7 Definition..................................................17		7 Definition..................................................17
	8 Security Considerations.....................................70		8 Security Considerations.....................................57
	8.1 VACM Access control.........................................70		8.1 VACM Access control.........................................57
	8.2 Privacy.....................................................72		8.2 Privacy.....................................................59
	8.3 Measurement aspects.........................................73		8.3 Measurement aspects.........................................59
	8.4 Management aspects..........................................73		8.4 Management aspects..........................................60
	9 Document management.........................................74		9 Document management.........................................61
	9.1 Open issues.................................................74		9.1 Open issues.................................................61
	9.2 Changes done since release 03...............................74		9.2 Changes done since release 04...............................61
	9.3 Changes done since release 02...............................75		9.3 Changes done since release 03...............................61
	10 References..................................................76		9.4 Changes done since release 02...............................62
	11 Acknowledgments.............................................77		10 References..................................................62
	12 Authors' Addresses..........................................77		11 Acknowledgments.............................................64
			12 Authors' Addresses..........................................64
	1. Introduction		1. Introduction
	This memo defines a MIB for managing network measurements based upon		This memo defines a MIB for managing network measurements based upon
	the IP performance metrics specified by the IPPM Working Group.		the IP performance metrics specified by the IPPM Working Group.
	The definition of objects in the IPPM MIB are built on notions		The definition of objects in the IPPM MIB are built on notions
	introduced and discussed in the IPPM Framework document, RFC 2330		introduced and discussed in the IPPM Framework document, RFC 2330
	[ii].		[ii].
	This memo defines a Management Information Base (MIB), and as such it		This memo defines a Management Information Base (MIB), and as such it
	skipping to change at page 3, line 18		skipping to change at page 3, line 18
	The IPPM Framework consists of 3 major components:		The IPPM Framework consists of 3 major components:
	A general framework for defining performance metrics, as described in		A general framework for defining performance metrics, as described in
	the Framework for IP Performance Metrics, RFC 2330 [2];		the Framework for IP Performance Metrics, RFC 2330 [2];
	A set of standardized metrics which conform to this framework: The		A set of standardized metrics which conform to this framework: The
	IPPM Metrics for Measuring Connectivity, RFC 2678 [iii]; The One-way		IPPM Metrics for Measuring Connectivity, RFC 2678 [iii]; The One-way
	Delay Metric for IPPM, RFC 2679 [iv]; The One-way Packet Loss Metric		Delay Metric for IPPM, RFC 2679 [iv]; The One-way Packet Loss Metric
	for IPPM, RFC 2680 [v]; The Round-trip Delay Metric for IPPM, RFC		for IPPM, RFC 2680 [v]; The Round-trip Delay Metric for IPPM, RFC
	2681 [vi].		2681 [vi];
	Emerging metrics that are being specified in respect of this		Emerging metrics that are being specified in respect of this
	framework.		framework.
	3. The SNMP Management Framework		3. The SNMP Management Framework
	The SNMP Management Framework consists of five major components:		The SNMP Management Framework consists of five major components:
	An overall architecture, described in RFC 2571 [2].		An overall architecture, described in RFC 2571 [2].
	skipping to change at page 5, line 22		skipping to change at page 5, line 22
	To permit metrics to be referenced by other MIBs and other protocols,		To permit metrics to be referenced by other MIBs and other protocols,
	the IPPM WG has defined a registry of the current metrics and a		the IPPM WG has defined a registry of the current metrics and a
	framework for the integration of future metrics in the [IPPM metrics		framework for the integration of future metrics in the [IPPM metrics
	registry].		registry].
	As the specification of new metrics is a continuous process, this		As the specification of new metrics is a continuous process, this
	memo defines a framework for the integration of the future		memo defines a framework for the integration of the future
	standardized metrics.		standardized metrics.
	The MIB architecture is inspired by the RMON model [xxiii],[xxiv]
	which specifies the MIB for the monitoring of a single point of
	measure. The IPPM-REPORTING-MIB differs from this model in that IPPM
	metrics measurement involves several points of measure and requires
	common references for time and for measure identification.
	The IPPM-REPORTING-MIB introduces a framework where each application		The IPPM-REPORTING-MIB introduces a framework where each application
	identifies its measures in an owner namespace. The administrator may		identifies its measures in an owner namespace. The administrator may
	grant access to a measure, or set of measures to another owner via		grant access to a measure, or set of measures to another owner via
	view based access control. As a result, one owner may compute		view based access control. As a result, one owner may compute
	aggregated metrics on another owner’s network measures.		aggregated metrics on another ownerÆs network measures.
	Different architectures may be used to perform metric measurements,		Different architectures may be used to perform metric measurements,
	using a control protocol and a test protocol. Different control		using a control protocol and a test protocol. Different control
	frameworks are suitable for performing measurements. The memo lists		frameworks are suitable for performing measurements. The memo lists
	them, while also looking for a way to integrate them with the IPPM-		them, while also looking for a way to integrate them with the IPPM-
	REPORTING-MIB. This section is for informational purposes only, and		REPORTING-MIB. This section is for informational purposes only, and
	is intended to help specify the relationship among the test protocol,		is intended to help specify the relationship among the test protocol,
	the control protocol and the IPPM-REPORTING-MIB.		the control protocol and the IPPM-REPORTING-MIB.
	Special care has been taken to provide a reporting mode suitable for		Special care has been taken to provide a reporting mode suitable for
	control protocols and test protocols. It addresses the need to		control protocols and test protocols. It addresses the need to
	provide access to results for the applications. Moreover, it may be		provide access to results for the applications.
	used to reduce the number of control frameworks.
	This MIB is intended to handle multiple concurrent sessions by SNMP		This MIB is intended to handle multiple concurrent sessions by SNMP
	applications. However, the SNMP requests are not necessarily to be		applications. However, the SNMP requests are not necessarily to be
	handled explicitly by the measurement devices, but can be sent to		handled explicitly by the measurement devices, but can be sent to
	middleware performing an aggregation function. This allows for		middleware performing an aggregation function. This allows for
	continuous collection of measurements and statistics computation.		continuous collection of measurements and statistics computation.
	4.1. Textual Conventions		4.1. Textual Conventions
	Seven types of data are introduced as textual conventions in this		Eight types of data are introduced as textual conventions in this
	document: IppmOwnerString, TimeUnit, TypeP, TypePaddress,		document: IppmOwnerString, IppmOwnerIndex, TimeUnit, PacketType,
	GMTTimeStamp, IppmStandardMetrics and IppmReportDefinition.		PacketTypeAddress, GMTTimeStamp, IppmStandardMetrics and
			IppmMetricResultFilter.
	4.1.1 IppmOwnerString		4.1.1 IppmOwnerString
	This octet string is used to represent the owners of the various		This octet string is used to represent the owners of the various
	measures and reports in the measurement system.		measures and reports in the measurement system.
	4.1.2 TimeUnit		4.1.2 IppmOwnerIndex
			This integer identifies an instance of an object in an owner
			namespace.
			4.1.3 TimeUnit
	This textual convention is used to indicate a unit of time, ranging		This textual convention is used to indicate a unit of time, ranging
	from nanosecond, microsecond, millisecond, second, hour, day, and		from nanosecond, microsecond, millisecond, second, hour, day, and
	week.		week.
	4.1.3 TypeP and TypePaddress		4.1.4 PacketType and PacketTypeAddress
	Section 13 of the IPPM framework [2] introduces the generic notion of		Section 13 of the IPPM framework [2] introduces the generic notion of
	a "packet of type P", because in some contexts the metric's value		a "packet of type P", because in some contexts the metric's value
	depends on the type of the packets involved in the metric. In the		depends on the type of the packets involved in the metric. In the
	definition of a metric, the type P will be explicitly defined,		definition of a metric, the type P will be explicitly defined,
	partially defined, or left generic. Measurement of metrics defined		partially defined, or left generic. Measurement of metrics defined
	with generic type P are made specific when performing actual		with generic type P are made specific when performing actual
	measurements. It is important that one be conscious of the exact type		measurements. It is important that one be conscious of the exact type
	of traffic being measured.		of traffic being measured.
	skipping to change at page 6, line 44		skipping to change at page 6, line 40
	capability to unambiguously configure the type P of the packets, and		capability to unambiguously configure the type P of the packets, and
	the parameters of the protocol suites of the type P.		the parameters of the protocol suites of the type P.
	RMON2 introduced the concept of protocol identifiers. RFC2895 [xxv]		RMON2 introduced the concept of protocol identifiers. RFC2895 [xxv]
	specifies a macro for the definition of protocol identifier. The		specifies a macro for the definition of protocol identifier. The
	RFC2896 [xxvi] defines the protocol identifiers for different		RFC2896 [xxvi] defines the protocol identifiers for different
	protocol encapsulation trees.		protocol encapsulation trees.
	The type P implementation relies on the MACRO PROTOCOL-IDENTIFIER		The type P implementation relies on the MACRO PROTOCOL-IDENTIFIER
	defined for identifying protocol suites in RMON2. It is achieved by		defined for identifying protocol suites in RMON2. It is achieved by
	defining the TypeP and the TypePaddress as new syntax in SMIv2		defining the PacketType and the PacketTypeAddress as new syntax in
	TEXTUAL-CONVENTION.		SMIv2 TEXTUAL-CONVENTION.
	4.1.3.1 Internet addresses		4.1.4.1 Internet addresses
	The section 14 of the IPPM framework defines (for the usual case of a		The section 14 of the IPPM framework defines (for the usual case of a
	unidirectional path through the Internet) the term "Src" and "Dst".		unidirectional path through the Internet) the term "Src" and "Dst".
	"Src" denotes the IP address of the beginning of the path, and "Dst"		"Src" denotes the IP address of the beginning of the path, and "Dst"
	denotes the IP address of the end.		denotes the IP address of the end.
	The section 3 of the RMON PI Reference specifies the Protocol		The section 3 of the RMON PI Reference specifies the Protocol
	Identifier Encoding rules, which consists briefly in a recursive		Identifier Encoding rules, which consists briefly in a recursive
	length value format. "Src" and "Dst" are protocol identifier		length value format. "Src" and "Dst" are protocol identifier
	parameters. Their values are encoded in separated fields using the		parameters. Their values are encoded in separated fields using the
	encoding rules of the protocol identifier, but without trailing		encoding rules of the protocol identifier, but without trailing
	parameters.		parameters.
	The packet encapsulation defined in an instance of TypeP embeds the		The packet encapsulation defined in an instance of PacketType embeds
	format of "Src" and "Dst" and their values. The type and value of		the format of "Src" and "Dst" and their values. The type and value of
	these addresses depend on the type P of the packet, IP version 4,		these addresses depend on the type P of the packet, IP version 4,
	IPV6, IP in IP... Both participate in the completion of the packet		IPV6, IP in IP... Both participate in the completion of the packet
	encoding.		encoding.
	Examples:		Examples:
	RFC2896 defines the protocol identifiers ip and ipip4. Should there		RFC2896 defines the protocol identifiers ip and ipip4. Should there
	be an Internet tunnel end-point of the IP address 192.168.1.1 in the		be an Internet tunnel end-point of the IP address 192.168.1.1 in the
	tunnel 128.2.6.7. the TypeP of the source address of the tunnel, Src,		tunnel 128.2.6.7. the PacketType of the source address of the tunnel,
	is 'ip.ipip4'. The encoding of 'ip.ipip4' using the RFC2895 rules		Src, is 'ip.ipip4'. The encoding of 'ip.ipip4' using the RFC2895
	adds a trailer 2.0.0. It means that an instance of this protocol		rules adds a trailer 2.0.0. It means that an instance of this
	identifier has 2 parameters, which values will be set only when		protocol identifier has 2 parameters, which values will be set only
	implemented. In the IPPM TypeP context these 2 parameters are		when implemented. In the IPPM PacketType context these 2 parameters
	provided in Src (or Dst). In the current example the value of Src is		are provided in Src (or Dst). In the current example the value of Src
	"192.168.1.1 128.2.6.7".		is "192.168.1.1 128.2.6.7".
	4.1.4 GMTTimeStamp		4.1.5 GMTTimeStamp
	This textual convention defines the time at which an event occurred.		This textual convention defines the time at which an event occurred.
	It is very similar to the NTP timestamp format except that it		It is very similar to the NTP timestamp format except that it
	represents the time elapsed since January 1st, 2000 instead of		represents the time elapsed since January 1st, 2000 instead of
	January 1st, 1900.		January 1st, 1900.
	4.1.5 IppmStandardMetrics		4.1.6 IppmStandardMetrics
	Each standard metric is identified in the IPPM-METRICS-REGISTRY under		Each standard metric is identified in the IPPM-METRICS-REGISTRY under
	the node rfc in chronological order. This textual convention defines		the node rfc in chronological order. This textual convention defines
	an octet string to permit several metrics to be performed in a single		an octet string to permit several metrics to be performed in a single
	measure.		measure.
	4.1.6 Report definition		4.1.7 Report definition
	A report consists of sending, or logging, a subset of results of		A report consists of sending, or logging, a subset of results of
	measurements that have been taken over a period of time. The report		measurements that have been taken over a period of time. The report
	defines actions that are taken on the measurement results. An action		defines actions that are taken on the measurement results. An action
	is performed either:		is performed either:
	+ For each result		+ For each result
	+ On the results corresponding to a measurement cycle		+ On the results corresponding to a measurement cycle
	+ On the results available at the measurement completion.		+ On the results available at the measurement completion.
	skipping to change at page 8, line 24		skipping to change at page 8, line 22
	One may also want to report when particular values (i.e. constantly		One may also want to report when particular values (i.e. constantly
	over a threshold) repeatedly occur over a period of time. For		over a threshold) repeatedly occur over a period of time. For
	example, if one-way-day is constantly over a specified acceptable		example, if one-way-day is constantly over a specified acceptable
	threshold value for 10 minutes, then the values should be reported.		threshold value for 10 minutes, then the values should be reported.
	The combination of IPPM metric results, threshold events, and event		The combination of IPPM metric results, threshold events, and event
	filtering provides a very efficient mechanism to report measurement		filtering provides a very efficient mechanism to report measurement
	results, events, and alarms.		results, events, and alarms.
	A report is described using the TEXTUAL-CONVENTION		A report is described using the TEXTUAL-CONVENTION
	IppmReportDefinition. The report setup must not dramatically increase		IppmMetricResultFilter. The report setup must not dramatically
	the amount of data needed by the control protocol to setup a measure:		increase the amount of data needed by the control protocol to setup a
			measure:
	+ A basic report is defined in the object ippmReportSetupDefinition;		+ A basic report is defined in the object ippmAggrMeasureFilter;
	+ More elaborate reports are described using a metric threshold to		+ More elaborate reports are described using a metric threshold to
	generate alarms and events.		generate alarms and events.
	+ The generation of alarms and reports requires a management station		+ The generation of alarms and reports requires a management station
	address to which the data will be sent.		address to which the data will be sent.
	+ SLA alarms are described using an events duration threshold.		+ SLA alarms are described using an events duration threshold.
	The TEXTUAL-CONVENTION IppmReportDefinition specifies the list of		The TEXTUAL-CONVENTION IppmMetricResultFilter specifies the list of
	events and actions that are used to create a report.		events and actions that are used to create a report.
	4.2 Structure of the MIB		4.2 Structure of the MIB
	The MIB is arranged as follow:		The MIB is arranged as follow:
	- ippmSystem		- ippmSystem Group:
	- ippmOwners		+ ippmPointOfMeasureTable;
			+ ippmSynchronizationTable;
			+ ippmMetricsTable.
	- ippmMeasure		- ippmOwners Group:
			-
			+ ippmOwnersTable;
	- ippmHistory		- ippmHistory Group:
			-
			+ ippmHistoryTable;
	- ippmNetMeasure		- ippmNetMeasure Group:
			-
			+ ippmNetMeasureTable;
	- ippmAggrMeasure		- ippmAggrMeasure Group:
	- ippmReport		-
			+ ippmAggrMeasureTable.
	- ippmNotifications		- ippmNotifications
	4.2.1 The ippmSystem Group		4.2.1 The ippmSystem Group
			The implementation of this group is mandatory.
	This group consists of a set of parameters describing the clock		This group consists of a set of parameters describing the clock
	synchronization at a particular point of measure over time, as well		synchronization at a particular point of measure over time, as well
	as the system clock where the IPPM-REPORTING-MIB agent resides.		as the system clock of the IPPM-REPORTING-MIB agent.
	This group is critical to the implementation of the IPPM MIB.		The table ippmPointOfMeasureTable describes the points of measure.
	Section 6.3. of the IPPM Framework states that		The table ippmSynchronisationTable is critical to the implementation,
			especially to be respectful of the Section 6.3. of the IPPM
			Framework, which states that
	"Those who develop such measurement methodologies should strive to:		"Those who develop such measurement methodologies should strive to:
	+ Minimize their uncertainties/errors,		+ Minimize their uncertainties/errors,
	+ Understand and document the sources of uncertainty/error, and		+ Understand and document the sources of uncertainty/error, and
	+ Quantify the amounts of uncertainty/error."		+ Quantify the amounts of uncertainty/error."
	The aim of this group is to have these values available to compute		Consequently the table ippmSynchronisationTable makes these values
	reliable statistics. The implementation of this group is mandatory,		available to compute reliable statistics.
	whether the time synchronization is automatic or not.
			The table ippmMetricsTable list all the IPPM metrics using the
			registry order and describes their implementation (unit...).
	4.2.2 The ippmOwners Group		4.2.2 The ippmOwners Group
	This group identifies an owner, or group of owners, that have access		This group identifies an owner, or group of owners, that have access
	to measurements on a probe.		to measurements on a probe.
	4.2.3 The ippmMeasure Group		4.2.3 The ippmHistory Group
	This group contains all the IPPM metrics that are registered and
	available for use by the agent.
	The measurement entity describes in the ippmMetricsTable of the SNMP
	agent the local implementation of the standardized metrics. All
	standardized metrics should be displayed in this table, with the
	ippmMetricCapabilities object defining whether the metric is
	implemented or not.
	4.2.4 The ippmHistory Group
	The results of any given measure are stored in the ippmHistoryTable.		The results of any given measure are stored in the ippmHistoryTable.
	The indexing is such that there is an entry in this table for each		The indexing is such that there is an entry in this table for each
	result of a given measure for a given metric.		result of a given measure for a given metric.
	4.2.5 The ippmNetMeasure Group		4.2.4 The ippmNetMeasure Group
	The control protocol registers a description of the existing network		The control protocol registers a description of the existing network
	measures in the ippmNetMeasureTable.		measures in the ippmNetMeasureTable.
	This group displays the network measures defined by the control		This group displays the network measures defined by the control
	protocol. The results are saved in the ippmHistoryTable.		protocol. The results are saved in the ippmHistoryTable.
	ippmNetMeasureTable is a reflection of the configuration of the		ippmNetMeasureTable is a reflection of the configuration of the
	network measure.		network measure.
	4.2.6 The ippmAggrMeasure Group		4.2.5 The ippmAggrMeasure Group
	ippmAggrMeasureTable is responsible for the consolidation, or
	aggregation, of results previously measured and saved in the
	ippmHistoryTable. The aggregated results are saved in the
	ippmHistoryTable and may be used for higher aggregated measures.
	4.2.7 The Report Group
	This group displays the existing reports of the measures collected.		ippmAggrMeasureTable is responsible for the aggregation of results.
	The ippmReportSetupTable is responsible for the configuration of the		The aggregated results are saved in the ippmHistoryTable and may be
	reports.		used for higher aggregated measures.
	The reports are saved in the ippmReportTable, or sent directly to
	management applications.
	4.2.8 The Notification Group		4.2.6 The Notification Group
	The Notification group specifies a list of valid notifications. They		The Notification group specifies a list of valid notifications. They
	are used to generate alarms, or reports, to management applications.		are used to generate alarms, or reports, to management applications.
	4.3 Row identification in an application namespace		4.3 Row identification in an application namespace
	The control protocol, or the test protocol, adds rows in the		IPPM metrics measurement is a distributed task. An owner namespace is
	namespace of the corresponding measure.		defined to avoid the need of polling to determine the next free
			index, to avoid index collision when 2 applications are looking for a
			new index as the same time; to increase the speed of the management
			operations; to reduce bandwidth consumption and to reduce CPU load in
			the agents and applications.
	An object instance identifier in an owner namespace is defined as a		In a MIB, an object instance identifier is defined by the clause
	list of objects in the clause INDEX where the first object type is		INDEX of the table as a list of objects.
	IppmOwnerString.
	As the OBJECT IDENTIFIER, which identifies the instance, begins with		The owner namespace is defined in the INDEX as a couple of 2 objects
	the owner value, the remaining values of the index fields may be		where the type of first one is IppmOwnerString and the type of the
	chosen independently from one namespace to another.		second is IppmOwnerIndex.
			The first term of the instance identifier is the name of the owner.
			The second term is an private index managed by the owner. This index
			value is unique in an owner namespace. Before the creation of an
			instance the creator pick up an IppmOwnerIndex value not in use.
	This allows the user to choose arbitrary values for the remaining		This allows the user to choose arbitrary values for the remaining
	fields of the INDEX clause without checking that the values of these		fields of the INDEX clause without checking that the values of these
	fields exists in the MIB tables. This allows the owner to use the		fields exists in the MIB tables. Moreover this allows the owner to
	same values across MIB implementations.		use the same instance identifier over a set of IPPM MIB
			implementations.
	Thus, it avoids polling to determine the next free index. Also, as a
	consequence, two applications will never find the same free index
	value.
	The usage of owner namespace increases the speed of the management
	operations while reducing bandwidth consumption and CPU load in the
	agents and applications.
	Measurements are requested by management applications. An instance of		Measurements are requested by management applications. An instance of
	an object managed by a management station is identified by the		an object managed by a management station is identified by the
	management station IppmOwnerString and the private index provided by		management station IppmOwnerString and the private index provided by
	the MS.		the MS.
	4.4 Relationship of IPPM REPORTING MIB tables		4.4 Relationship of IPPM REPORTING MIB tables
	There is inherently a relationship between various tables in the IPPM		There is inherently a relationship between various tables in the IPPM
	REPORTING MIB, and as such, the data integrity must be assured. This		REPORTING MIB, and as such, the data integrity must be assured. This
	relationship is depicted in the following examples.		relationship is depicted in the following examples.
	skipping to change at page 12, line 8		skipping to change at page 11, line 51
	The network measure table is read-only, thus entries in this table		The network measure table is read-only, thus entries in this table
	must be populated by the agent upon startup.		must be populated by the agent upon startup.
	The agent could potentially read a database that contains network		The agent could potentially read a database that contains network
	measures configured by a 3rd party proprietary management system that		measures configured by a 3rd party proprietary management system that
	directly interacts with the points of measure. However, the "owner"		directly interacts with the points of measure. However, the "owner"
	of the measure must be defined in the owners table. It may be either		of the measure must be defined in the owners table. It may be either
	configured directly, or exported to the agent by the external		configured directly, or exported to the agent by the external
	measurement tool.		measurement tool.
	The aggregated measure table allows for an "owner" to create		The aggregated measure table allows for an "owner" to create
	aggregated measures (such as average, minimum, maximum) on existing		aggregated measures (such as average, minimum, maximum...) on
	measures. An owner may even create aggregated measures on network		existing measures. An owner may even create aggregated measures on
	measures that are owned by other owners. However, it is recommended		network measures that are owned by other owners. However, it is
	to use view based access control to grant access of network measures		recommended to use view based access control to grant access of
	to other owners in the system.		network measures to other owners in the system.
	5 Measurement architectures		5 Measurement architectures
	There are three main measurement architectures.		There are three main measurement architectures.
	5.1 Proxy architecture		5.1 Proxy architecture
	. +----+ +----+		. +----+ +----+
	. |NMS1| |NMS2|		. |NMS1| |NMS2|
	. +----+ +----+		. +----+ +----+
	skipping to change at page 12, line 44		skipping to change at page 12, line 37
	. | |		. | |
	. OWDP-Control		. OWDP-Control
	. | |		. | |
	. +----------+ +----------+		. +----------+ +----------+
	. | |		. | |
	. v v		. v v
	.+----------------+ +------------------+		.+----------------+ +------------------+
	.| Packets-Sender |--OWDP-Test-->| Packets-Receiver |		.| Packets-Sender |--OWDP-Test-->| Packets-Receiver |
	.+----------------+ +------------------+		.+----------------+ +------------------+
	In this architecture, the different NMS’s query the IPPM-REPORTING-		In this architecture, the different NMSÆs query the IPPM-REPORTING-
	MIB agent for measurements. The agent controls whether the NMS is		MIB agent for measurements. The agent controls whether the NMS is
	granted access to perform the measure requested. Each NMS may access		granted access to perform the measure requested. Each NMS may access
	the results of its measurements in the IPPM-REPORTING-MIB history		the results of its measurements in the IPPM-REPORTING-MIB history
	table.		table.
	The measurement setup/teardown and the data collection are done using		The measurement setup/teardown and the data collection are done using
	the control protocol and the test protocol.		the control protocol and the test protocol.
	In this mode the NMS does not depend on the control protocol nor on		In this mode the NMS does not depend on the control protocol nor on
	the test protocol. The entities involved in the measurement do not		the test protocol. The entities involved in the measurement do not
	skipping to change at page 13, line 36		skipping to change at page 13, line 30
	. | | | |		. | | | |
	. | OWDP | OWDP		. | OWDP | OWDP
	. |Control |Control		. |Control |Control
	. | | | |		. | | | |
	. | | +------------------------------+		. | | +------------------------------+
	. | | | | |		. | | | | |
	. | | +--|---------------------------+ |		. | | +--|---------------------------+ |
	. | | | | | |		. | | | | | |
	. | +--|--|------------------------+ | |		. | +--|--|------------------------+ | |
	. | | | | | | |		. | | | | | | |
	. +--------+---------------------+ | | |		. +--------+---------------------+ | |
	. | | | | | | | |		. | | | | | | | |
	. | | | | | | | |		. | | | | | | | |
	. v v v v v v v v		. v v v v v v v v
	. +------------------+ +------------------+		. +------------------+ +------------------+
	. |IPPM-REPORTING-MIB| |IPPM-REPORTING-MIB|		. |IPPM-REPORTING-MIB| |IPPM-REPORTING-MIB|
	. | agent | | agent |		. | agent | | agent |
	. +------------------+ +------------------+		. +------------------+ +------------------+
	. | Packets-Sender |--OWDP-Test-->| Packets-Receiver |		. | Packets-Sender |--OWDP-Test-->| Packets-Receiver |
	. +------------------+ +------------------+		. +------------------+ +------------------+
	The activation of a measure by the control protocol or the test		The activation of a measure by the control protocol or the test
	protocol creates a measure in the IPPM-REPORTING-MIB Network Measure		protocol creates a measure in the IPPM-REPORTING-MIB Network Measure
	table. The table in question may be not accessible by SNMP. In this		table. The table in question may be not accessible by SNMP. In this
	case, a list of the measure identifiers (owner, index) is handled by		case, a list of the measure identifiers (owner, index) is handled by
	the measurement software.		the measurement software.
	Each timestamped result of the measure is logged in the IPPM-		Each timestamped result of the measure is logged in the IPPM-
	REPORTING-MIB History table in order to allow read access to the		REPORTING-MIB History table in order to allow read access to the
	NMS’s and event handling.		NMSÆs and event handling.
	On completion, the measurement results are managed according to the		On completion, the measurement results are managed according to the
	measure setup:		measure setup:
	+ The results may be sent to an NMS;		+ The results may be sent to an NMS;
	+ They may be dropped from the IPPM-REPORTING-MIB History table.		+ They may be dropped from the IPPM-REPORTING-MIB History table.
	In this mode, it is recommended to use an SNMPv2 Inform PDU to send		In this mode, it is recommended to use an SNMPv2 Inform PDU to send
	reporting events because it ensures that the entire block of the		reporting events because it ensures that the entire block of the
	result is received. There is no control using SNMP Trap PDU.		result is received. There is no control using SNMP Trap PDU.
	skipping to change at page 16, line 48		skipping to change at page 16, line 48
	The description of the measure is distributed to the points of		The description of the measure is distributed to the points of
	measure involved. The distribution may not be synchronized.		measure involved. The distribution may not be synchronized.
	6.1 Integration		6.1 Integration
	The integration of the IPPM-REPORTING-MIB, and the test and control		The integration of the IPPM-REPORTING-MIB, and the test and control
	protocols consists in pushing the network measure setup/teardown		protocols consists in pushing the network measure setup/teardown
	parameters and the result values from the measurement software to the		parameters and the result values from the measurement software to the
	IPPM-REPORTING-MIB agent.		IPPM-REPORTING-MIB agent.
	6.2 Setup of the measure network		6.2 Setup of the network measure table
	The measurement system updates the MIB on creation of a network measure.		The measurement system updates the MIB on creation of a network measure.
	6.3 Setup of a measurement report		6.3 Setup of the aggregated measure table
	A measurement report setup describes events and data to include in
	the report. A report is read by an NMS in the ippmReportTable, or
	exported to an NMS using an SNMP trap, SNMP Inform PDU, an email, or
	an SMS.
	Different types of reports may be combined:		There are 2 ways to setup an aggregated measure:
	+ A trivial report defines the results to be saved in the		The measurement system updates the MIB on creation of an aggregated
	ippmReportTable;		measure;
	+ A basic report defines the host to which the results are sent		An SNMP application creates an aggregated measure.
	on completion of the measure;
	+ An alarm report defines a threshold on the results of the
	measure. A message is sent to a host when the result rises above,
	or falls below the threshold;
	+ An SLA report defines a threshold on the results of the
	measure. The report consists of the results of the measure (time
	and value) of the filtered events. The reports are sent at each
	measurement cycle, or when the measure completes.
	6.4 Updating the history of the MIB		6.4 Updating the history of the MIB
	Results have to be written by the measurement task in the agent		Results have to be written by the measurement task in the agent
	implementing the IPPM REPORTING MIB.		implementing the IPPM REPORTING MIB.
	Adding the results of a measurement consists in the transfer of the		Adding the results of a measurement consists in the transfer of the
	result from the measurement software to the SNMP agent. The protocol		result from the measurement software to the SNMP agent. The protocol
	that provides the result may be the control protocol, or the test		that provides the result may be the control protocol, or the test
	protocol, or another mechanism.		protocol, or another mechanism.
	6.5 Report download and upload		6.5 Default value
	A report is read in the ippmReportTable using SNMP, or generated by
	the IPPM_MIB agent using a SNMP Inform PDU, an email or a SMS.
	6.6 Default value
	The default values correspond to IP version 4.		The default values correspond to IP version 4.
	7 Definition		7 Definition
	IPPM-REPORTING-MIB DEFINITIONS ::= BEGIN		IPPM-REPORTING-MIB DEFINITIONS ::= BEGIN
	IMPORTS		IMPORTS
	MODULE-IDENTITY,		MODULE-IDENTITY,
	NOTIFICATION-TYPE,		NOTIFICATION-TYPE,
	skipping to change at page 18, line 21		skipping to change at page 17, line 52
	RowStatus,		RowStatus,
	StorageType,		StorageType,
	TEXTUAL-CONVENTION		TEXTUAL-CONVENTION
	FROM SNMPv2-TC		FROM SNMPv2-TC
	MODULE-COMPLIANCE,		MODULE-COMPLIANCE,
	OBJECT-GROUP,		OBJECT-GROUP,
	NOTIFICATION-GROUP		NOTIFICATION-GROUP
	FROM SNMPv2-CONF;		FROM SNMPv2-CONF;
	ippmReportingMib MODULE-IDENTITY		ippmReportingMib MODULE-IDENTITY
	LAST-UPDATED "200310141200Z" -- 14 October 2003		LAST-UPDATED "200402121200Z" -- 12 February 2004
	ORGANIZATION "France Telecom - R&D"		ORGANIZATION "France Telecom - R&D"
	CONTACT-INFO		CONTACT-INFO
	"Emile Stephan		"Emile Stephan
	France Telecom - R&D		France Telecom - R&D
	2, Avenue Pierre Marzin		2, Avenue Pierre Marzin
	Technopole Anticipa		Technopole Anticipa
	22307 Lannion Cedex		22307 Lannion Cedex
	FRANCE		FRANCE
	Tel: + 33 2 96 05 36 10		Tel: + 33 2 96 05 36 10
	E-mail: emile.stephan@francetelecom.com		E-mail: emile.stephan@francetelecom.com
	skipping to change at page 19, line 4		skipping to change at page 18, line 34
	reporting of measurement results."		reporting of measurement results."
	REVISION "200210181200Z" -- 18 October 2002		REVISION "200210181200Z" -- 18 October 2002
	DESCRIPTION		DESCRIPTION
	"General cleanup		"General cleanup
	Change 5 tables to read write"		Change 5 tables to read write"
	REVISION "200302141200Z" -- 14 February 2003		REVISION "200302141200Z" -- 14 February 2003
	DESCRIPTION		DESCRIPTION
	"Modifications based upon feedback from IETF-55"		"Modifications based upon feedback from IETF-55"
	REVISION "200306291200Z" -- 29 June 2003		REVISION "200306291200Z" -- 29 June 2003
	DESCRIPTION		DESCRIPTION
	"Adaptation to VACM, preparation of the final version"		"Adaptation to VACM, preparation of the final version"
	REVISION "200310241200Z" -- 24 October 2003		REVISION "200310241200Z" -- 24 October 2003
	DESCRIPTION		DESCRIPTION
	"Modifications based upon feedback from experimental		"Modifications based upon feedback from experimental
	implementation."		implementation."
			REVISION "200402121200Z" -- 12 February 2004
			DESCRIPTION
			"Modifications based upon feedback 58th IETF: The report group
			and the corresponding notification are removed."
	::= { experimental 10001 } -- XXX to be assigned by IANA		::= { experimental 10001 } -- XXX to be assigned by IANA
	ippm OBJECT IDENTIFIER ::= { experimental 10000 }		ippm OBJECT IDENTIFIER ::= { experimental 10000 }
	--		--
	-- TEXTUAL-CONVENTION		-- TEXTUAL-CONVENTION
	--		--
	IppmOwnerString ::= TEXTUAL-CONVENTION		IppmOwnerString ::= TEXTUAL-CONVENTION
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"An OwnerString. The length is limited to 32 bytes."		"The owner namespace is defined in the INDEX of a table as a
			couple of 2 objects where the type of the first one is
			IppmOwnerString and the type of the second is IppmOwnerIndex.
			IppmOwnerString is an OwnerString which length is limited to 32
			bytes."
	SYNTAX OCTET STRING (SIZE (0..32))		SYNTAX OCTET STRING (SIZE (0..32))
			IppmOwnerIndex ::= TEXTUAL-CONVENTION
			STATUS current
			DESCRIPTION
			"The owner namespace is defined in the INDEX of a table as a
			couple of 2 objects where the type of first one is
			IppmOwnerString and the type of the second is IppmOwnerIndex.
			An object of type IppmOwnerIndex uniquely identifies a row of a
			table inside an owner namespace.
			Inside one namespace several objects of type IppmOwnerIndex
			coexist and share the IppmOwnerIndex range of values to provide a
			unique instance identifier.
			"
			SYNTAX Unsigned32 (1.. 65535)
	TimeUnit ::= TEXTUAL-CONVENTION		TimeUnit ::= TEXTUAL-CONVENTION
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"A enumerated list of time units."		"A enumerated list of time units."
	SYNTAX INTEGER {		SYNTAX INTEGER {
	week(1),		week(1),
	day(2),		day(2),
	hour(3),		hour(3),
	minute(4),		minute(4),
	second(5),		second(5),
	skipping to change at page 20, line 18		skipping to change at page 20, line 18
	The first bit of the string has the index 0. The index 1		The first bit of the string has the index 0. The index 1
	corresponds to the first metric of the registry		corresponds to the first metric of the registry
	(instantaneousUnidirectionalConnectivity ).		(instantaneousUnidirectionalConnectivity ).
	Example:		Example:
	One-way-Delay(6) is identified as the leaf number 6 of the node		One-way-Delay(6) is identified as the leaf number 6 of the node
	rfc of the registry. One-way-Packet-Loss(12) is identified as the		rfc of the registry. One-way-Packet-Loss(12) is identified as the
	leaf number 12 of the node		leaf number 12 of the node
	rfc of the registry. A network measure performing both One-way-		rfc of the registry. A network measure performing both One-way-
	Delay(6) and One-way-Packet-Loss(12) will be described as		Delay(6) and One-way-Packet-Loss(12) will be described as
	'0000001000001000'b, '1040'B.		'0001000001000000'b, '1040'B.
	"		"
	SYNTAX OCTET STRING (SIZE (1..64))		SYNTAX OCTET STRING (SIZE (1..64))
			IppmMetricsRegistryIndex ::= TEXTUAL-CONVENTION
			STATUS current
			DESCRIPTION
			"IppmMetricsRegistryIndex defines an unambiguous index for each
			standardized metric. It identifies a metric, and as such its
			value is the value of the node of the metric in the IPPM
			registry. This value is the same in any implementation of the
			IPPM REPORTING MIB.
			Example:
			In the IPPM-METRICS-REGISTRY, onewayPacketLossAverage is
			registered as the node 14 of ippmMetricsRegistry.metrics.rfc.
			Consequently the index of the metric onewayPacketLossAverage in
			the IppmMetricsTable will always be '14'. At large an instance,
			which type is IppmMetricsRegistryIndex and which value is '14',
			points to the metric onewayPacketLossAverage."
			SYNTAX Unsigned32 (1.. 65535)
	GMTTimeStamp ::= TEXTUAL-CONVENTION		GMTTimeStamp ::= TEXTUAL-CONVENTION
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The time value at which a specific occurrence took place. The		"The time value at which a measure or an event took place.
	specific occurrence must be defined in the description of any
	object defined using this type.
	field octets contents range		field octets contents range
	----- ------ -------- -----		----- ------ -------- -----
	1 1-4 second since 1 Jan 2000 0H00* 0..2^31 - 1		1 1-4 second since 1 Jan 1900 0H00* 0..2^31 - 1
	2 5-8 fractional part of the second* 0..2^32 - 1		2 5-8 fractional part of the second* 0..2^32 - 1
	* the value is in network-byte order		* the value is in network-byte order
	The timestamp format is directly inspired from the NTP timestamp		The timestamp format is the NTP timestamp format [RFC 1305].
	format.		The reference of time is GMT.
	It differs in that it counts the seconds since 1 Jan 2000 0H00
	instead of 1 Jan 1900 0H00. The most significant bit of the part
	that represents the second is reserved. It will wrap in year 2068
	(The NTP timestamp will wrap in year 2036).
	This bit is set to indicate if the fractional part of the second
	contains a precision field and a synchronization field as
	initially proposed in the OWAMP draft.
	When this bit is not set, the resolution is maximal.
	The maximal resolution is close to 250 picoseconds.
	The precision of the timestamp must be provided in another field.
	"		"
	SYNTAX OCTET STRING (SIZE (8))		SYNTAX OCTET STRING (SIZE (8))
	TypeP ::= TEXTUAL-CONVENTION		PacketType ::= TEXTUAL-CONVENTION
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"This textual convention is a display string used to describe the		"This textual convention is a display string used to describe the
	protocol encapsulation list of a packet, and is used as the value		protocol encapsulation list of a packet, and is used as the value
	of the SYNTAX clause for the type of the Src and Dst of an IPPM		of the SYNTAX clause for the type of the Src and Dst of an IPPM
	measure. The RFC2895 specifies a macro named PROTOCOL-IDENTIFIER		measure. The RFC2895 specifies a macro named PROTOCOL-IDENTIFIER
	for the definition of protocol identifiers, while its companion		for the definition of protocol identifiers, while its companion
	document, the RFC2896 defines a set of protocol identifiers.		document, the RFC2896 defines a set of protocol identifiers.
	TypeP is defined as a display string. It consists of a list of		PacketType is defined as a display string. It consists of a list
	dot separated protocol names. Each protocol name has been		of dot separated protocol names. Each protocol name has been
	previously defined using the macro PROTOCOL-IDENTIFIER of the RFC		previously defined using the macro PROTOCOL-IDENTIFIER of the RFC
	2895.		2895.
	Examples:		Examples:
	The RFC2896 defines the protocol identifiers 'ether2', 'ip',		The RFC2896 defines the protocol identifiers 'ether2', 'ip',
	'ipip4', 'udp', 'tcp', 'telnet'...		'ipip4', 'udp', 'tcp', 'telnet'...
	The TypeP of the source address corresponding to telnet is the		The PacketType of the source address corresponding to telnet is
	string 'ip.tcp.telnet'.		the string 'ip.tcp.telnet'.
	The TypeP of the source address corresponding to UDP packets sent		The PacketType of the source address corresponding to UDP packets
	in an IP tunnel is the string 'ip.ipip4.udp'.		sent in an IP tunnel is the string 'ip.ipip4.udp'.
	Note:		Note:
	An IPPM measure is active, so generally a TypeP value does not		An IPPM measure is active, so generally a PacketType value does
	describe the link layer (i.e. ether2...). Valid Internet packets		not describe the link layer (i.e. ether2...). Valid Internet
	are sent from Src to Dst. Then the choice of the link layer		packets are sent from Src to Dst. Then the choice of the link
	relies on the Internet stack."		layer relies on the Internet stack."
	SYNTAX OCTET STRING (SIZE (0..512))		SYNTAX OCTET STRING (SIZE (0..512))
	TypePaddress ::= TEXTUAL-CONVENTION		PacketTypeAddress ::= TEXTUAL-CONVENTION
	DISPLAY-HINT "255a"		DISPLAY-HINT "255a"
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"This textual convention is a Display string used to describe the		"This textual convention is a Display string used to describe the
	parameters of the protocol encapsulation list of a packet,		parameters of the protocol encapsulation list of a packet,
	basically the address.		basically the address.
	TypePaddress is defined as a display string. It consists in a		PacketTypeAddress is defined as a display string. It consists in
	list of blank separated addresses that reflect the encapsulation		a list of blank separated addresses that reflect the
	of the TypeP. Each parameter in the list corresponds to a		encapsulation of the PacketType. Each parameter in the list
	parameter of a PROTOCOL-IDENTIFIER of the TypeP.		corresponds to a parameter of a PROTOCOL-IDENTIFIER of the
			PacketType.
	Example:		Example:
	The TypeP 'ip.ipip4' has 2 parameters. A valid TypePaddress value
	is '192.168.1.1 128.2.6.7'."		The PacketType 'ip.ipip4' has 2 parameters. A valid
			PacketTypeAddress value is '192.168.1.1 128.2.6.7'."
	SYNTAX OCTET STRING (SIZE (0..512))		SYNTAX OCTET STRING (SIZE (0..512))
	IppmReportDefinition ::= TEXTUAL-CONVENTION		IppmMetricResultFilter ::= TEXTUAL-CONVENTION
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	" A report definition is a list of statements describing a report. A		" Given that not all results from a metric measurement are
	statement is part of this process if a corresponding bit in the		pertinent, and that the size of the history must be limited whenever
	definition is set to '1'. For all bit values that are set to one, a		possible, the TC IppmMetricResultFilter defines basic filters to
	report will be generated.		limit the among of data collected:
	The report process uses results saved in the history table. Threshold
	values are provided by the report setup.
	Given that not all results from a metric measurement are
	pertinent to a particular report, and that the size of the report
	must be limited whenever possible, the guidelines for the definition
	of a report are as follows:
	+ Select the events for consideration (1);
	+ Configure filters to select pertinent values (2);
	+ Describe the way the report is delivered (3);
	+ Describe clean up actions to perform on report completion (4);
	-1- events
	Events determine when a report is processed. Events are
	exclusive. The possible values are:
	onSingleton:
	The report is processed each time a new result of the measurement
	occurs.
	onMeasureCycle:
	The report is processed each time a cycle of measure is
	completed.
	onMeasureCompletion:
	The report is processed at the end of the measurement.
	-2- filters
	Filters determine if a result belongs to a report.
	ReportInBandResults and ReportOutBandResults are exclusive. The
	usage of ReportInBandResults and ReportOutBandResults exclude the
	usage of ReportAboveResults and ReportBelowResults.
	Possible values are:
	reportUpAndDownResults:
	Report contiguous results that are on opposite sides of
	the up and down metric threshold.
	ReportInBandResults:
	Report results lower than the high metric threshold
	field of the report setup and greater than the low
	metric threshold field of the report setup.
	ReportOutBandResults:
	Report results greater than the high metric threshold
	field of the report setup or lower than the low metric
	threshold field of the report setup.
	ReportAboveResults:
	Report results greater than the high metric threshold
	field of the report setup.
	ReportBelowResults:
	Report results lower than the low metric threshold field
	of the report setup.
	reportExceededEventsDuration:
	Save the results of the metric only if the current
	filter triggers repeatedly for a series of contiguous
	results during more than
	ippmReportSetupDurationThreshold seconds.
	-3- deliver		Filter's parameters are the 2 fields ippmAggrMeasureLowThreshold and
			ippmAggrMeasureLowThreshold of the aggregated measure setup.
	Even though report delivery statements are not exclusive, care		A filter determines if the result of the current aggregation has to
	should be taken to limit the number of report methods to 2. The		be stored:
	delivery methods are:
	inIppmReportTable:		LogInBandValue:
	Store the report in the local ippmReportTable.		The value is stored if it is lower than the high threshold of
	NOTE WELL: Results are not stored in the report table if		the aggregated measure setup and greater than the low
	this flag is not set.		threshold of of the aggregated measure setup.
	inSNMPv2TrapPDU:		LogOutBandValue:
	Send the report using a SNMPv2-Trap-PDU.		The value is stored if it is greater than the high threshold
			of the aggregated measure setup or lower than the low
			threshold of the aggregated measure setup.
	inInformRequestPDU:		LogAboveValue:
	Send the report using a SNMP InformRequest-PDU.		The value is stored if it is greater than the high threshold
			of the aggregated measure setup.
	inEmail:		LogBelowValue:
	Send the report using an email.		The value is stored if it is lower than the low metric
			threshold field of the aggregated measure setup.
	inSMS:		logUpAndDownValue:
	Send the report using a SMS.		This filter stores contiguous results that are on opposite
			sides of the up and down metric thresholds:
			A result is stored if it is the first result aggregated:
			If it is greater than the high threshold and lower than the
			low threshold then its value is set to the value of the low
			threshold;
	-4- Cleanup		A result greater than the high threshold is stored if the
	onReportDeliveryClearReport(12):		previous result is lower than the low threshold;
	Remove all the results corresponding to this measure		A result lower than the low threshold is stored if the
	from the ippmReportTable when the report has been		previous result is greater than the high threshold;
	delivered. This must be set in conjunction with
	inIppmReportTable, and onMeasureCompletion.
	"		"
	SYNTAX BITS {		SYNTAX INTEGER {
	none(0), -- reserved		logInBandValue(1),
	onSingleton(1),		logOutBandValue(2),
	onMeasureCycle(2),		logAboveValue(3),
	onMeasureCompletion(3),		logBelowValue(4),
	reportUpAndDownResults(4),		logUpAndDownValue(5)
	reportInBandResults(5),
	reportOutBandResults(6),
	reportAboveResults(7),
	reportBelowResults(8),
	reportExceededEventsDuration(9),
	inIppmReportTable(10),
	inSNMPv2TrapPDU(11),
	inInformRequestPDU(12),
	inEmail(13),
	inSMS(14),
	onReportDeliveryClearReport(15)
	}		}
	--		--
	-- IPPM Notifications		-- IPPM Notifications
	--		--
	ippmNotifications OBJECT IDENTIFIER ::= { ippm 0 }		ippmNotifications OBJECT IDENTIFIER ::= { ippm 0 }
	--		--
	-- IPPM Conformance		-- IPPM Conformance
	--		--
	ippmConformance OBJECT IDENTIFIER ::= { ippm 1 }		ippmConformance OBJECT IDENTIFIER ::= { ippm 1 }
	--		--
	-- IPPM MIB Object definitions		-- IPPM MIB Object definitions
	--		--
	ippmSystem OBJECT IDENTIFIER ::= { ippmReportingMib 1 }		ippmSystem OBJECT IDENTIFIER ::= { ippmReportingMib 1 }
	ippmOwners OBJECT IDENTIFIER ::= { ippmReportingMib 2 }		ippmOwners OBJECT IDENTIFIER ::= { ippmReportingMib 2 }
	ippmHistory OBJECT IDENTIFIER ::= { ippmReportingMib 3 }		ippmHistory OBJECT IDENTIFIER ::= { ippmReportingMib 3 }
	ippmMeasure OBJECT IDENTIFIER ::= { ippmReportingMib 4 }		ippmNetMeasure OBJECT IDENTIFIER ::= { ippmReportingMib 4 }
	ippmReport OBJECT IDENTIFIER ::= { ippmReportingMib 5 }		ippmAggrMeasure OBJECT IDENTIFIER ::= { ippmReportingMib 5 }
	--		--
	-- ippmSystem Group		-- ippmSystem Group
	--		--
	--		--
	ippmSystemTime OBJECT-TYPE		ippmSystemTime OBJECT-TYPE
	SYNTAX GMTTimeStamp		SYNTAX GMTTimeStamp
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	skipping to change at page 26, line 31		skipping to change at page 25, line 15
	unknown(0),		unknown(0),
	up(1),		up(1),
	down(2)		down(2)
	}		}
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"This object describes the status of the system running the IPPM		"This object describes the status of the system running the IPPM
	REPORTING MIB SNMP agent. It does not describe end point measurement		REPORTING MIB SNMP agent. It does not describe end point measurement
	status.		status.
	unknown(0)		unknown(0) means the service is unknown.
	up(1) means service is operational and available for general use.		up(1) means the service is operational and available for general
			use.
	down(2) means the agent is not available for use.		down(2) means the agent is not available for use.
	"		"
	::= { ippmSystem 5 }		::= { ippmSystem 5 }
			ippmSystemAggregatedMetrics OBJECT-TYPE
			SYNTAX IppmStandardMetrics
			MAX-ACCESS read-only
			STATUS current
			DESCRIPTION
			" ippmSystemAggregatedMetrics lists the aggregated metrics that
			are performed in the SNMP agent instead of in the point of
			measure."
			::= { ippmSystem 6 }
	ippmSynchronizationTable OBJECT-TYPE		ippmSynchronizationTable OBJECT-TYPE
	SYNTAX SEQUENCE OF IppmSynchronizationEntry		SYNTAX SEQUENCE OF IppmSynchronizationEntry
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"This table registers the event related to the synchronization of		"This table registers the event related to the synchronization of
	the points of measure. Each event is described in an		the points of measure. Each event is described in an
	ippmSynchronizationEntry.		ippmSynchronizationEntry.
	ippmSynchronizationTable is mandatory.		ippmSynchronizationTable is mandatory.
	ippmSynchronizationTable content is read only."		ippmSynchronizationTable content is read only."
	::= { ippmSystem 6 }		::= { ippmSystem 7 }
	ippmSynchronizationEntry OBJECT-TYPE		ippmSynchronizationEntry OBJECT-TYPE
	SYNTAX IppmSynchronizationEntry		SYNTAX IppmSynchronizationEntry
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"An entry describes a modification of the synchronization status.		"An entry describes a modification of the synchronization
	"		status."
	INDEX { ippmPointOfMeasureIndex, ippmSynchronizationIndex }		INDEX { ippmPointOfMeasureIndex, ippmSynchronizationIndex }
	::= { ippmSynchronizationTable 1 }		::= { ippmSynchronizationTable 1 }
	IppmSynchronizationEntry ::=		IppmSynchronizationEntry ::=
	SEQUENCE {		SEQUENCE {
	ippmSynchronizationIndex Unsigned32,		ippmSynchronizationIndex Unsigned32,
	ippmSynchronizationTime GMTTimeStamp,		ippmSynchronizationTime GMTTimeStamp,
	ippmSynchronizationStratum Unsigned32,		ippmSynchronizationStratum Unsigned32,
	ippmSynchronizationResolution Unsigned32		ippmSynchronizationResolution Unsigned32
	}		}
	ippmSynchronizationIndex OBJECT-TYPE		ippmSynchronizationIndex OBJECT-TYPE
	SYNTAX Unsigned32 (1 .. 65535)		SYNTAX Unsigned32 (1 .. 65535)
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"An index that identifies the synchronization events in		"An index that identifies the synchronization events in
	chronological order."		chronological order.
			65535 is an arbitrary size. It is not recommended to keep
			permanently a history of 65535 events."
	::= { ippmSynchronizationEntry 1 }		::= { ippmSynchronizationEntry 1 }
	ippmSynchronizationTime OBJECT-TYPE		ippmSynchronizationTime OBJECT-TYPE
	SYNTAX GMTTimeStamp		SYNTAX GMTTimeStamp
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The time when the synchronization event occurs."		"The time when the synchronization event occurs."
	::= { ippmSynchronizationEntry 2 }		::= { ippmSynchronizationEntry 2 }
	skipping to change at page 28, line 22		skipping to change at page 27, line 19
	It is the list of the measurement end points of the set of probes		It is the list of the measurement end points of the set of probes
	for which the IPPM agent provides an SNMP interface.		for which the IPPM agent provides an SNMP interface.
	IPPM MIB implemented in a probe:		IPPM MIB implemented in a probe:
	It is the list of the measurement end points of the probe.		It is the list of the measurement end points of the probe.
	The ippmPointOfMeasureTable content is read only. This implies		The ippmPointOfMeasureTable content is read only. This implies
	that the measurement software handles the table internally		that the measurement software handles the table internally
	ippmPointOfMeasureTable is mandatory."		ippmPointOfMeasureTable is mandatory."
	::= { ippmSystem 7 }		::= { ippmSystem 8 }
	ippmPointOfMeasureEntry OBJECT-TYPE		ippmPointOfMeasureEntry OBJECT-TYPE
	SYNTAX IppmPointOfMeasureEntry		SYNTAX IppmPointOfMeasureEntry
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	" An entry may be the management address of some middleware in		" An entry may be the management address of some middleware in
	charge of the management of a set of probes. It may the		charge of the management of a set of probes. It may the
	management address of a probe that contains several line cards.		management address of a probe that contains several line cards.
	An entry describes the capability of a point of measure. The		An entry describes the capability of a point of measure.
	description may make the use of wildcards to define multiple
	capabilities."		ippmPointOfMeasureMetrics lists the metrics handles by the point
			of measure."
	INDEX { ippmPointOfMeasureIndex }		INDEX { ippmPointOfMeasureIndex }
	::= { ippmPointOfMeasureTable 1 }		::= { ippmPointOfMeasureTable 1 }
	IppmPointOfMeasureEntry ::= SEQUENCE {		IppmPointOfMeasureEntry ::= SEQUENCE {
	ippmPointOfMeasureIndex Unsigned32,		ippmPointOfMeasureIndex Unsigned32,
	ippmPointOfMeasureMgmtAddrType InetAddressType,		ippmPointOfMeasureMgmtAddrType InetAddressType,
	ippmPointOfMeasureMgmtAddress InetAddress,		ippmPointOfMeasureMgmtAddress InetAddress,
	ippmPointOfMeasureTestAddrTypeP TypeP,		ippmPointOfMeasureTestAddrType InetAddressType,
	ippmPointOfMeasureTestAddr TypePaddress,		ippmPointOfMeasureTestAddress InetAddress,
	ippmPointOfMeasureMetrics IppmStandardMetrics		ippmPointOfMeasureMetrics IppmStandardMetrics
	}		}
	ippmPointOfMeasureIndex OBJECT-TYPE		ippmPointOfMeasureIndex OBJECT-TYPE
	SYNTAX Unsigned32 (1 .. 65535)		SYNTAX Unsigned32 (1 .. 65535)
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"A local index that identifies an entry in the point of measure		"A local index that identifies an entry in the point of measure
	table."		table."
	skipping to change at page 29, line 24		skipping to change at page 28, line 22
	::= { ippmPointOfMeasureEntry 2 }		::= { ippmPointOfMeasureEntry 2 }
	ippmPointOfMeasureMgmtAddress OBJECT-TYPE		ippmPointOfMeasureMgmtAddress OBJECT-TYPE
	SYNTAX InetAddress (SIZE (1..128))		SYNTAX InetAddress (SIZE (1..128))
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The management address on the point of measure"		"The management address on the point of measure"
	::= { ippmPointOfMeasureEntry 3 }		::= { ippmPointOfMeasureEntry 3 }
	ippmPointOfMeasureTestAddrTypeP OBJECT-TYPE		ippmPointOfMeasureTestAddrType OBJECT-TYPE
	SYNTAX TypeP		SYNTAX InetAddressType
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Defines the address type of the measurement interface of the		"Defines the address type of the measurement interface of the
	point of measure."		point of measure."
	::= { ippmPointOfMeasureEntry 4 }		::= { ippmPointOfMeasureEntry 4 }
	ippmPointOfMeasureTestAddr OBJECT-TYPE		ippmPointOfMeasureTestAddress OBJECT-TYPE
	SYNTAX TypePaddress		SYNTAX InetAddress
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Specifies the address of the measurement interface for the point		"Specifies the address of the measurement interface for the point
	of measure."		of measure."
	::= { ippmPointOfMeasureEntry 5}		::= { ippmPointOfMeasureEntry 5}
	ippmPointOfMeasureMetrics OBJECT-TYPE		ippmPointOfMeasureMetrics OBJECT-TYPE
	SYNTAX IppmStandardMetrics		SYNTAX IppmStandardMetrics
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Metrics supported by this point of measure."		" ippmPointOfMeasureMetrics lists the metrics this point of
			measure implements."
	::= { ippmPointOfMeasureEntry 6 }		::= { ippmPointOfMeasureEntry 6 }
	ippmMetricTable OBJECT-TYPE		ippmMetricsTable OBJECT-TYPE
	SYNTAX SEQUENCE OF IppmMetricEntry		SYNTAX SEQUENCE OF IppmMetricsEntry
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"This table is mandatory. It describes the current		"This table is mandatory. It describes the current
	implementation. Each IPPM standardized metric must be described		implementation. Each IPPM standardized metric must be described
	in the table.		in the table.
	ippmMetricTable content is read only."		ippmMetricsTable content is read only."
	::= { ippmSystem 8 }		::= { ippmSystem 9 }
	ippmMetricEntry OBJECT-TYPE		ippmMetricsEntry OBJECT-TYPE
	SYNTAX IppmMetricEntry		SYNTAX IppmMetricsEntry
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"An entry describes the static capabilities of a metric		"An entry describes the static capabilities of a metric
	implementation."		implementation."
	INDEX { ippmMetricIndex }		INDEX { ippmMetricsIndex }
	::= { ippmMetricTable 1 }		::= { ippmMetricsTable 1 }
	IppmMetricEntry ::=		IppmMetricsEntry ::=
	SEQUENCE {		SEQUENCE {
	ippmMetricIndex Unsigned32,		ippmMetricsIndex IppmMetricsRegistryIndex,
	ippmMetricCapabilities INTEGER,		ippmMetricsType INTEGER,
	ippmMetricType INTEGER,		ippmMetricsUnit INTEGER,
	ippmMetricUnit INTEGER,		ippmMetricsDescription SnmpAdminString
	ippmMetricDescription SnmpAdminString
	}		}
	ippmMetricIndex OBJECT-TYPE		ippmMetricsIndex OBJECT-TYPE
	SYNTAX Unsigned32 (1.. 65535)		SYNTAX IppmMetricsRegistryIndex
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"ippmMetricIndex defines an unambiguous index for each		"ippmMetricsIndex defines an unambiguous index for each
	standardized metric. It identifies a metric, and as such its		standardized metric. It identifies a metric, and as such its
	value is the value of the node of the metric in an IPPM registry.		value is the value of the node of the metric in the IPPM
	This value is the same in any implementation of the IPPM		registry. This value is the same in any implementation of the
	REPORTING MIB.		IPPM REPORTING MIB.
	Example:		Example:
	In the IPPM-METRICS-REGISTRY, onewayPacketLossAverage is		In the IPPM-METRICS-REGISTRY, onewayPacketLossAverage is
	registered as the node 14 of ippmMetricsRegistry.metrics.rfc.		registered as the node 14 of ippmMetricsRegistry.metrics.rfc.
	Consequently the index of the metric onewayPacketLossAverage in		Consequently the index of the metric onewayPacketLossAverage in
	the IppmMetricTable will always be '14'"		the IppmMetricsTable will always be '14'"
	::= { ippmMetricEntry 1 }		::= { ippmMetricsEntry 1 }
	ippmMetricCapabilities OBJECT-TYPE
	SYNTAX INTEGER {
	notImplemented(0),
	implemented(1)
	}
	MAX-ACCESS read-only
	STATUS current
	DESCRIPTION
	"A value of notImplemented implies the metric is not implemented.
	A value of implemented implies the metric is implemented either
	in the proxy or the point of measure itself.
	Example: if the aggregated metric is not implemented in the point
	of measure it may be implemented in the proxy."
	::= { ippmMetricEntry 2 }
	ippmMetricType OBJECT-TYPE		ippmMetricsType OBJECT-TYPE
	SYNTAX INTEGER {		SYNTAX INTEGER {
	network(0),		network(0),
	aggregated(1)		aggregated(1)
	}		}
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Indicates the metric type, whether it is network or aggregated"		"Indicates the metric type, whether it is network or aggregated"
	::= { ippmMetricEntry 3 }		::= { ippmMetricsEntry 2 }
	ippmMetricUnit OBJECT-TYPE		ippmMetricsUnit OBJECT-TYPE
	SYNTAX INTEGER {		SYNTAX INTEGER {
	noUnit(0),		noUnit(0),
	second(1),		second(1),
	millisecond(2),		millisecond(2),
	microsecond(3),		microsecond(3),
	nanosecond(4),		nanosecond(4),
	percentage(5),		percentage(5),
	packet(6),		packet(6),
	byte(7),		byte(7),
	kilobyte(8),		kilobyte(8),
	megabyte(9)		megabyte(9)
	}		}
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The unit used in the current entity for the results of the		"The unit used in the current entity for the results of the
	measurement of this metric."		measurement of this metric."
	::= { ippmMetricEntry 4 }		::= { ippmMetricsEntry 3 }
	ippmMetricDescription OBJECT-TYPE		ippmMetricsDescription OBJECT-TYPE
	SYNTAX SnmpAdminString		SYNTAX SnmpAdminString
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"A textual description of the metric implementation following the		"A textual description of the metric implementation following the
	exact name of this metric in the registry. For example:		exact name of this metric in the registry. For example:
	oneWayDelay: OWD Metric ."		oneWayDelay: OWD Metric ."
	::= { ippmMetricEntry 5 }		::= { ippmMetricsEntry 4 }
	--		--
	-- ippmOwners Group		-- ippmOwners Group
	--		--
	-- The ippmOwners objects are responsible for managing		-- The ippmOwners objects are responsible for managing
	-- the owners access to the measurements.		-- the owners access to the measurements.
	--		--
	--		--
	ippmOwnersTable OBJECT-TYPE		ippmOwnersTable OBJECT-TYPE
	SYNTAX SEQUENCE OF IppmOwnersEntry		SYNTAX SEQUENCE OF IppmOwnersEntry
	skipping to change at page 32, line 33		skipping to change at page 31, line 16
	ippmOwnersEntry OBJECT-TYPE		ippmOwnersEntry OBJECT-TYPE
	SYNTAX IppmOwnersEntry		SYNTAX IppmOwnersEntry
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The description of the resources granted to an SNMP application.		"The description of the resources granted to an SNMP application.
	For example, an instance of ippmOwnersOwner with an		For example, an instance of ippmOwnersOwner with an
	IppmOwnerString 'acme', which represents the 14th owner created		IppmOwnerString 'acme', which represents the 14th owner created
	in ippmOwnersTable would be named ippmOwnersEntryOwner.14.		in ippmOwnersTable would be named ippmOwnersEntryOwner.14.
			"
	Notes:		INDEX { ippmOwnersOwner }
	The ippmOwnersIndex value is a local index managed directly by
	the agent. The management application must poll to get the next
	available index value.
	It is not used in anyway in other IPPM tables."
	INDEX { ippmOwnersIndex }
	::= { ippmOwnersTable 1 }		::= { ippmOwnersTable 1 }
	IppmOwnersEntry ::= SEQUENCE {		IppmOwnersEntry ::= SEQUENCE {
	ippmOwnersIndex Unsigned32,
	ippmOwnersOwner IppmOwnerString,		ippmOwnersOwner IppmOwnerString,
	ippmOwnersGrantedMetrics IppmStandardMetrics,		ippmOwnersGrantedMetrics IppmStandardMetrics,
	ippmOwnersQuota Unsigned32,		ippmOwnersQuota Unsigned32,
	ippmOwnersIpAddressType InetAddressType,		ippmOwnersIpAddressType InetAddressType,
	ippmOwnersIpAddress InetAddress,		ippmOwnersIpAddress InetAddress,
	ippmOwnersEmail SnmpAdminString,		ippmOwnersEmail SnmpAdminString,
	ippmOwnersSMS SnmpAdminString,
	ippmOwnersStatus RowStatus		ippmOwnersStatus RowStatus
	}		}
	ippmOwnersIndex OBJECT-TYPE
	SYNTAX Unsigned32 (1.. 65535)
	MAX-ACCESS not-accessible
	STATUS current
	DESCRIPTION
	"An arbitrary index that identifies an entry in the owners
	table."
	::= { ippmOwnersEntry 1 }
	ippmOwnersOwner OBJECT-TYPE		ippmOwnersOwner OBJECT-TYPE
	SYNTAX IppmOwnerString		SYNTAX IppmOwnerString
	MAX-ACCESS read-create		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The owner described by this entry."		"The owner described by this entry."
	::= { ippmOwnersEntry 2 }		::= { ippmOwnersEntry 1 }
	ippmOwnersGrantedMetrics OBJECT-TYPE		ippmOwnersGrantedMetrics OBJECT-TYPE
	SYNTAX IppmStandardMetrics		SYNTAX IppmStandardMetrics
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	" Defines the metrics granted to an owner for which measurements		" Defines the metrics granted to an owner for which measurements
	can be performed."		can be performed."
	::= { ippmOwnersEntry 3 }		::= { ippmOwnersEntry 2 }
	ippmOwnersQuota OBJECT-TYPE		ippmOwnersQuota OBJECT-TYPE
	SYNTAX Unsigned32		SYNTAX Unsigned32
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	" The maximum number of records that this owner may have in the		" The maximum number of records that this owner may have in the
	history table and in the report table."		history table and in the report table."
	::= { ippmOwnersEntry 4 }		::= { ippmOwnersEntry 3 }
	ippmOwnersIpAddressType OBJECT-TYPE		ippmOwnersIpAddressType OBJECT-TYPE
	SYNTAX InetAddressType		SYNTAX InetAddressType
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The IP address type of the management entity corresponding to		"The IP address type of the management entity corresponding to
	this owner.		this owner.
	InetAddressType is restricted to ipv4(1),ipv6(2)and dns(16). "		InetAddressType is restricted to ipv4(1),ipv6(2)and dns(16). "
	::= { ippmOwnersEntry 5 }		::= { ippmOwnersEntry 4 }
	ippmOwnersIpAddress OBJECT-TYPE		ippmOwnersIpAddress OBJECT-TYPE
	SYNTAX InetAddress (SIZE (1..128))		SYNTAX InetAddress (SIZE (1..128))
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The IP address of the management entity corresponding to this		"The IP address of the management entity corresponding to this
	owner. For example, the IP address of the management console used		owner. For example, the IP address of the management console used
	to send SNMP requests."		to send SNMP requests."
	::= { ippmOwnersEntry 6 }		::= { ippmOwnersEntry 5 }
	ippmOwnersEmail OBJECT-TYPE		ippmOwnersEmail OBJECT-TYPE
	SYNTAX SnmpAdminString		SYNTAX SnmpAdminString
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The email address of the management entity corresponding to this		"The email address of the management entity corresponding to this
	owner."		owner."
	::= { ippmOwnersEntry 7 }		::= { ippmOwnersEntry 6 }
	ippmOwnersSMS OBJECT-TYPE
	SYNTAX SnmpAdminString
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"The SMS phone number of the management entity corresponding to
	this owner."
	::= { ippmOwnersEntry 8 }
	ippmOwnersStatus OBJECT-TYPE		ippmOwnersStatus OBJECT-TYPE
	SYNTAX RowStatus		SYNTAX RowStatus
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The status of this table entry. Once this status is set to		"The status of this table entry. Once this status is set to
	active, the corresponding entry in the table may not be		active, the corresponding entry in the table may not be
	modified."		modified."
	::= { ippmOwnersEntry 9 }		::= { ippmOwnersEntry 7 }
	--		--
			-- ippmHistory Group
	--		--
	--		--
	-- ippmHistoryTable		-- ippmHistoryTable
	--		--
	ippmHistoryTable OBJECT-TYPE		ippmHistoryTable OBJECT-TYPE
	SYNTAX SEQUENCE OF IppmHistoryEntry		SYNTAX SEQUENCE OF IppmHistoryEntry
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The table containing the measurement results."		"The table containing the measurement results."
	skipping to change at page 35, line 23		skipping to change at page 33, line 27
	In the index :		In the index :
	+ ippmHistoryMeasureOwner identifies the owner of the measure;		+ ippmHistoryMeasureOwner identifies the owner of the measure;
	+ ippmHistoryMeasureIndex identifies the measure in the owner		+ ippmHistoryMeasureIndex identifies the measure in the owner
	namespace;		namespace;
	+ ippmHistoryMetricIndex identifies the metric measured by the		+ ippmHistoryMetricIndex identifies the metric measured by the
	measure. The metric is described in the corresponding entry of		measure. The metric is described in the corresponding entry of
	the ippmMetricTable;		the ippmMetricsTable;
	+ ippmHistorySeqence is the sequence number of the measurement		+ ippmHistorySequence is the sequence number of the measurement
	result for an entry in the history table."		result for an entry in the history table."
	INDEX { ippmHistoryMeasureOwner, ippmHistoryMeasureIndex,		INDEX { ippmHistoryMeasureOwner, ippmHistoryMeasureIndex,
	ippmHistoryMetricIndex, ippmHistorySequence }		ippmHistoryMetricIndex, ippmHistorySequence }
	::= { ippmHistoryTable 1 }		::= { ippmHistoryTable 1 }
	IppmHistoryEntry ::=		IppmHistoryEntry ::=
	SEQUENCE {		SEQUENCE {
	ippmHistoryMeasureOwner IppmOwnerString,		ippmHistoryMeasureOwner IppmOwnerString,
	ippmHistoryMeasureIndex Unsigned32,		ippmHistoryMeasureIndex IppmOwnerIndex,
	ippmHistoryMetricIndex Unsigned32,		ippmHistoryMetricIndex IppmMetricsRegistryIndex,
	ippmHistorySequence Unsigned32,		ippmHistorySequence Unsigned32,
	ippmHistoryTimestamp GMTTimeStamp,		ippmHistoryTimestamp GMTTimeStamp,
	ippmHistoryValue Integer32		ippmHistoryValue Integer32
	}		}
	ippmHistoryMeasureOwner OBJECT-TYPE		ippmHistoryMeasureOwner OBJECT-TYPE
	SYNTAX IppmOwnerString		SYNTAX IppmOwnerString
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The owner of the measure that produced this result."		"The owner of the measure that produced this result. The measure
			is either an ippmNetMeasure or an ippmAggrMeasure."
	::= { ippmHistoryEntry 1 }		::= { ippmHistoryEntry 1 }
	ippmHistoryMeasureIndex OBJECT-TYPE		ippmHistoryMeasureIndex OBJECT-TYPE
	SYNTAX Unsigned32 (1.. 65535)		SYNTAX IppmOwnerIndex
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	" The owner index of the measure that produced this result."		"The owner index of the measure that produced this result. The
			measure is either an entry of the ippmNetMeasureTable or of the
			ippmAggrMeasureTable."
	::= { ippmHistoryEntry 2 }		::= { ippmHistoryEntry 2 }
	ippmHistoryMetricIndex OBJECT-TYPE		ippmHistoryMetricIndex OBJECT-TYPE
	SYNTAX Unsigned32 (1.. 65535)		SYNTAX IppmMetricsRegistryIndex
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	" ippmHistoryMetricIndex identifies the metric measured by the		" ippmHistoryMetricIndex identifies the metric measured by the
	measure. The metric is described in the corresponding entry of		measure. The metric is described in the corresponding entry of
	the ippmMetricTable."		the ippmMetricsTable."
	::= { ippmHistoryEntry 3 }		::= { ippmHistoryEntry 3 }
	ippmHistorySequence OBJECT-TYPE		ippmHistorySequence OBJECT-TYPE
	SYNTAX Unsigned32 (0..4294967295)		SYNTAX Unsigned32 (0..4294967295)
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"ippmHistorySequence is the sequence number of the measurement		"ippmHistorySequence is the sequence number of the measurement
	results for a metric.		results for a metric.
	Network metrics:		Network metrics:
	It's the sequence number of a measurement packet. Typically, it		It's the sequence number of a measurement packet. Typically, it
	identifies the order of the packet in the stream of packets sent		identifies the order of the packet in the stream of packets sent
	by the source.		by the source.
	Aggregated metrics:		Aggregated metrics:
	It is the sequence number of the computed aggregated metric		It is the sequence order of the aggregation computed."
	result."
	::= { ippmHistoryEntry 4 }		::= { ippmHistoryEntry 4 }
	ippmHistoryTimestamp OBJECT-TYPE		ippmHistoryTimestamp OBJECT-TYPE
	SYNTAX GMTTimeStamp		SYNTAX GMTTimeStamp
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The timestamp when the measurement occurred."		"The timestamp when the measurement occurred."
	::= { ippmHistoryEntry 5 }		::= { ippmHistoryEntry 5 }
	ippmHistoryValue OBJECT-TYPE		ippmHistoryValue OBJECT-TYPE
	SYNTAX Integer32		SYNTAX Integer32
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The observed value of the measurement."		"The observed value of the measurement."
	::= { ippmHistoryEntry 6 }		::= { ippmHistoryEntry 6 }
			ippmHistoryPathToResults OBJECT-TYPE
			SYNTAX SnmpAdminString
			MAX-ACCESS read-only
			STATUS current
			DESCRIPTION
			"It is typically an URL describing the file location where bulk
			results are logged."
			::= { ippmHistory 2 }
	--		--
			-- ippmNetMeasure Group
	--		--
	--		--
	-- ippmNetMeasureTable		-- ippmNetMeasureTable
	--		--
	--		--
	ippmNetMeasureTable OBJECT-TYPE		ippmNetMeasureTable OBJECT-TYPE
	SYNTAX SEQUENCE OF IppmNetMeasureEntry		SYNTAX SEQUENCE OF IppmNetMeasureEntry
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"An entry is a measurement that performs network measures and		"An entry is a measurement that performs network measures and
	provides results.		provides results.
	It performs several metric measurements per packet exchange. Each		It performs several metric measurements per packet exchange. Each
	step of a measure produces a singleton result per metric. The		step of a measure produces a singleton result per metric. The
	time of the measurement and the value of the metric are saved in		time of the measurement and the value of the metric are saved in
	the ippmHistoryTable."		the ippmHistoryTable."
	::= { ippmMeasure 1 }		::= { ippmNetMeasure 1 }
	ippmNetMeasureEntry OBJECT-TYPE		ippmNetMeasureEntry OBJECT-TYPE
	SYNTAX IppmNetMeasureEntry		SYNTAX IppmNetMeasureEntry
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	" The IppmNetMeasureTable is mandatory, and its content is read		" The IppmNetMeasureTable is mandatory, and its content is read
	only. It means that the measurement software handles the table		only. It means that the measurement software handles the table
	internally. The setup of the network measure is not permitted		internally. The setup of the network measure is not permitted
	through the IPPM REPORTING MIB. As an example, OWAP provides a		through the IPPM REPORTING MIB. As an example, OWAP provides a
	setup protocol to setup and tear down networks measures.		setup protocol to setup and tear down networks measures.
	The ippmNetMeasureMetrics is set to a list of metrics to be		The ippmNetMeasureMetrics is set to a list of metrics to be
	computed from the same raw packet exchange. Each step of		computed from the same raw packet exchange. Each step of
	measurement delivers a singleton per chosen metric. Results are		measurement delivers a singleton per metric. Results are
	timestamped and saved in the ippmHistoryTable.		timestamped and saved in the ippmHistoryTable.
	One may create aggregated measures by using the results of		One may create aggregated measures by using the results of
	network measures. They may be referenced by their table index		network measures."
	values. "
	INDEX { ippmNetMeasureOwner, ippmNetMeasureIndex }		INDEX { ippmNetMeasureOwner, ippmNetMeasureIndex }
	::= { ippmNetMeasureTable 1 }		::= { ippmNetMeasureTable 1 }
	IppmNetMeasureEntry ::= SEQUENCE {		IppmNetMeasureEntry ::= SEQUENCE {
	ippmNetMeasureOwner IppmOwnerString,		ippmNetMeasureOwner IppmOwnerString,
	ippmNetMeasureIndex Unsigned32,		ippmNetMeasureIndex IppmOwnerIndex,
	ippmNetMeasureName SnmpAdminString,		ippmNetMeasureName SnmpAdminString,
	ippmNetMeasureMetrics IppmStandardMetrics,		ippmNetMeasureMetrics IppmStandardMetrics,
	ippmNetMeasureBeginTime GMTTimeStamp,		ippmNetMeasureBeginTime GMTTimeStamp,
	ippmNetMeasureCollectionRateUnit TimeUnit,		ippmNetMeasureCollectionRateUnit TimeUnit,
	ippmNetMeasureCollectionRate Unsigned32,		ippmNetMeasureCollectionRate Unsigned32,
	ippmNetMeasureDurationUnit TimeUnit,		ippmNetMeasureDurationUnit TimeUnit,
	ippmNetMeasureDuration Unsigned32,		ippmNetMeasureDuration Unsigned32,
	ippmNetMeasureHistorySize Unsigned32,		ippmNetMeasureHistorySize Unsigned32,
	ippmNetMeasureFailureMgmtMode INTEGER,		ippmNetMeasureFailureMgmtMode INTEGER,
	ippmNetMeasureResultsMgmt INTEGER,		ippmNetMeasureResultsMgmt INTEGER,
	ippmNetMeasureSrcTypeP TypeP,		ippmNetMeasureSrcPacketType PacketType,
	ippmNetMeasureSrc TypePaddress,		ippmNetMeasureSrc PacketTypeAddress,
	ippmNetMeasureDstTypeP TypeP,		ippmNetMeasureDstPacketType PacketType,
	ippmNetMeasureDst TypePaddress,		ippmNetMeasureDst PacketTypeAddress,
	ippmNetMeasureTxMode INTEGER,		ippmNetMeasureTxMode INTEGER,
	ippmNetMeasureTxPacketRateUnit TimeUnit,		ippmNetMeasureTxPacketRateUnit TimeUnit,
	ippmNetMeasureTxPacketRate Unsigned32,		ippmNetMeasureTxPacketRate Unsigned32,
	ippmNetMeasureMedOrBurstSize Unsigned32,		ippmNetMeasureMedOrBurstSize Unsigned32,
	ippmNetMeasureDevOrIntBurstSize Unsigned32,		ippmNetMeasureDevOrIntBurstSize Unsigned32,
	ippmNetMeasureLossTimeout Unsigned32,		ippmNetMeasureLossTimeout Unsigned32,
	ippmNetMeasureL3PacketSize Unsigned32,		ippmNetMeasureL3PacketSize Unsigned32,
	ippmNetMeasureDataPattern OCTET STRING,		ippmNetMeasureDataPattern OCTET STRING,
	ippmNetMeasureMap SnmpAdminString,
	ippmNetMeasureTotalPktsRecv Counter64,		ippmNetMeasureTotalPktsRecv Counter64,
	ippmNetMeasureLastUpdate GMTTimeStamp,		ippmNetMeasureLastUpdate GMTTimeStamp,
	ippmNetMeasureOperState INTEGER		ippmNetMeasureOperState INTEGER
	}		}
	ippmNetMeasureOwner OBJECT-TYPE		ippmNetMeasureOwner OBJECT-TYPE
	SYNTAX IppmOwnerString		SYNTAX IppmOwnerString
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The owner of the network measure."		"The owner of the network measure."
	::= { ippmNetMeasureEntry 1 }		::= { ippmNetMeasureEntry 1 }
	ippmNetMeasureIndex OBJECT-TYPE		ippmNetMeasureIndex OBJECT-TYPE
	SYNTAX Unsigned32 (1.. 65535)		SYNTAX IppmOwnerIndex
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The owner index of the network measure."		"The owner index of the network measure."
	::= { ippmNetMeasureEntry 2 }		::= { ippmNetMeasureEntry 2 }
	ippmNetMeasureName OBJECT-TYPE		ippmNetMeasureName OBJECT-TYPE
	SYNTAX SnmpAdminString		SYNTAX SnmpAdminString
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The name of the metric instance(s)as defined in		"The name of the metric instance(s)as defined in
	ippmNetMeasureMetrics. It illustrates the specificity of the		ippmNetMeasureMetrics. It illustrates the specificity of the
	metric(s) and includes the metric(s) and the TypeP.		metric(s) and includes the metric(s) and the PacketType.
	Example:		Example:
	IP-TCP-HTTP-One-way-Delay: free text "		IP-TCP-HTTP-One-way-Delay: free text "
	::= { ippmNetMeasureEntry 3 }		::= { ippmNetMeasureEntry 3 }
	ippmNetMeasureMetrics OBJECT-TYPE		ippmNetMeasureMetrics OBJECT-TYPE
	SYNTAX IppmStandardMetrics		SYNTAX IppmStandardMetrics
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Defines the metrics to compute within this measure. ONLY network		"ippmNetMeasureMetrics defines the metrics to compute within this
	metrics of the same type are allowed in this field.		measure. Only network metrics of the same type are allowed in
	A measure may be configured for the result of different metric		this field (e.g. poisson-based metrics and periodic-based metrics
	singletons to be archived in the ippmHistoryTable. The		are incompatibles, while one-way delay and packet loss are
	ippmMetricIndex of the created result has the value of the bit		generally processed simultaneously: a very bad delay is
	index of the corresponding ippmMeasureMetrics as explained above		potentially a very good packet loss).
	in the ippmMetricIndex definition.
			Results are saved in the ippmHistoryTable. Results of a metric
			are identified using an index of type IppmMetricsRegistryIndex.
	Example:		Example:
	A measure asking for One-way-Delay(6) and One-way-Packet-Loss(12)		Given a multi-metrics measure of One-way-Delay(6) and One-way-
	generated a flow of singletons which are logged in the		Packet-Loss(12). The value of the field ippmNetMeasureMetrics is
	ippmHistoryTable. The singletons created for the One-way-Delay		'0001000001000000'b, '1040'B. Results are logged in the
	measure have a value of ippmMetricIndex of 6 while the created		ippmHistoryTable where One-way-Delay singletons have a value of
	singletons for the One-way-Packet-Loss measure have a value of		ippmMetricsIndex of 6 while One-way-Packet-Loss singletons have a
	ippmMetricIndex of 12.		value of ippmMetricsIndex of 12.
	"		"
	::= { ippmNetMeasureEntry 4 }		::= { ippmNetMeasureEntry 4 }
	ippmNetMeasureBeginTime OBJECT-TYPE		ippmNetMeasureBeginTime OBJECT-TYPE
	SYNTAX GMTTimeStamp		SYNTAX GMTTimeStamp
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Specifies the time at which the measurement begins."		"Specifies the time at which the measurement begins."
	skipping to change at page 41, line 33		skipping to change at page 39, line 51
	This object indicates the way the measurement results are managed		This object indicates the way the measurement results are managed
	when the owner quota has been exceeded:		when the owner quota has been exceeded:
	'wrap'		'wrap'
	continue the measurement and erase the older entries in the		continue the measurement and erase the older entries in the
	history.		history.
	'suspend'		'suspend'
	stop the measure and keep the results in the history.		stop the measure and keep the results in the history.
	"		"
	::= { ippmNetMeasureEntry 12 }		::= { ippmNetMeasureEntry 12 }
	ippmNetMeasureSrcTypeP OBJECT-TYPE		ippmNetMeasureSrcPacketType OBJECT-TYPE
	SYNTAX TypeP		SYNTAX PacketType
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Defines the type P of the source address of the packets sent by		"Defines the type P of the source address of the packets sent by
	the measure."		the measure."
	::= { ippmNetMeasureEntry 13 }		::= { ippmNetMeasureEntry 13 }
	ippmNetMeasureSrc OBJECT-TYPE		ippmNetMeasureSrc OBJECT-TYPE
	SYNTAX TypePaddress		SYNTAX PacketTypeAddress
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Specifies the address of the source of the measure.		"Specifies the address of the source of the measure.
	It is represented as a list of parameters corresponding to those		It is represented as a list of parameters corresponding to those
	of the PROTOCOL IDENTIFIER set in ippmNetMeasureSrcTypeP."		of the PROTOCOL IDENTIFIER set in ippmNetMeasureSrcPacketType."
	::= { ippmNetMeasureEntry 14}		::= { ippmNetMeasureEntry 14}
	ippmNetMeasureDstTypeP OBJECT-TYPE		ippmNetMeasureDstPacketType OBJECT-TYPE
	SYNTAX TypeP		SYNTAX PacketType
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Defines the type P of the destination address of the packets		"Defines the type P of the destination address of the packets
	sent by the measure."		sent by the measure."
	::= { ippmNetMeasureEntry 15 }		::= { ippmNetMeasureEntry 15 }
	ippmNetMeasureDst OBJECT-TYPE		ippmNetMeasureDst OBJECT-TYPE
	SYNTAX TypePaddress		SYNTAX PacketTypeAddress
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Specifies the address of the destination of the measure.		"Specifies the address of the destination of the measure.
	It is represented as a list of parameters corresponding to those		It is represented as a list of parameters corresponding to those
	of the PROTOCOL IDENTIFIER set in ippmNetMeasureDstTypeP."		of the PROTOCOL IDENTIFIER set in ippmNetMeasureDstPacketType."
	::= { ippmNetMeasureEntry 16 }		::= { ippmNetMeasureEntry 16 }
	ippmNetMeasureTxMode OBJECT-TYPE		ippmNetMeasureTxMode OBJECT-TYPE
	SYNTAX INTEGER {		SYNTAX INTEGER {
	other(0),		other(0),
	periodic(1),		periodic(1),
	poisson(2),		poisson(2),
	multiburst(3)		multiburst(3)
	}		}
	MAX-ACCESS read-only		MAX-ACCESS read-only
	skipping to change at page 43, line 45		skipping to change at page 42, line 12
	"		"
	::= { ippmNetMeasureEntry 20 }		::= { ippmNetMeasureEntry 20 }
	ippmNetMeasureDevOrIntBurstSize OBJECT-TYPE		ippmNetMeasureDevOrIntBurstSize OBJECT-TYPE
	SYNTAX Unsigned32		SYNTAX Unsigned32
	UNITS "Packets"		UNITS "Packets"
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"		"
	Multi-burst mode: This field indicates the gap between 2		Multi-burst mode: This field indicates the gap between 2 bursts,
	bursts, in number of packets.		in number of packets.
	Example:		Example:
	If TxPacketRateUnit/TxPacketRate is 100 packets/second,		If TxPacketRateUnit/TxPacketRate is 100 packets/second,
	and DevOrIntBurstSize equals 50 packets, then the gap		and DevOrIntBurstSize equals 50 packets, then the gap between 2
	between 2 bursts is		bursts is
	equal to 50*1/100, or 1/2 second.		equal to 50*1/100, or 1/2 second.
	Poisson mode:		Poisson mode:
	This field indicates the typical difference between the packets		This field indicates the typical difference between the packets
	of the period corresponding to the median.		of the period corresponding to the median.
	"		"
	::= { ippmNetMeasureEntry 21 }		::= { ippmNetMeasureEntry 21 }
	ippmNetMeasureLossTimeout OBJECT-TYPE		ippmNetMeasureLossTimeout OBJECT-TYPE
	SYNTAX Unsigned32		SYNTAX Unsigned32
	UNITS "Milliseconds"		UNITS "Milliseconds"
	MAX-ACCESS read-only		MAX-ACCESS read-only
	skipping to change at page 44, line 28		skipping to change at page 42, line 44
	by the sink."		by the sink."
	::= { ippmNetMeasureEntry 22 }		::= { ippmNetMeasureEntry 22 }
	ippmNetMeasureL3PacketSize OBJECT-TYPE		ippmNetMeasureL3PacketSize OBJECT-TYPE
	SYNTAX Unsigned32		SYNTAX Unsigned32
	UNITS "Bytes"		UNITS "Bytes"
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Specifies the size of the packets counted at the IP network		"Specifies the size of the packets counted at the IP network
	layer in regards to the TypeP definition.		layer in regards to the PacketType definition.
	Example: For a TypeP 'ip ipip4' the L3 size will be the size of		Example: For a PacketType 'ip ipip4' the L3 size will be the size
	the packet at ipip4 level.		of the packet at ipip4 level.
	"		"
	::= { ippmNetMeasureEntry 23 }		::= { ippmNetMeasureEntry 23 }
	ippmNetMeasureDataPattern OBJECT-TYPE		ippmNetMeasureDataPattern OBJECT-TYPE
	SYNTAX OCTET STRING		SYNTAX OCTET STRING
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The pattern used to fill the payload of the packet."		"The pattern used to fill the payload of the packet."
	::= { ippmNetMeasureEntry 24 }		::= { ippmNetMeasureEntry 24 }
	ippmNetMeasureMap OBJECT-TYPE
	SYNTAX SnmpAdminString
	MAX-ACCESS read-only
	STATUS current
	DESCRIPTION
	"An administrative name of a network management map to which the
	measure belongs."
	::= { ippmNetMeasureEntry 25 }
	ippmNetMeasureTotalPktsRecv OBJECT-TYPE		ippmNetMeasureTotalPktsRecv OBJECT-TYPE
	SYNTAX Counter64		SYNTAX Counter64
	UNITS "Packets"		UNITS "Packets"
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Reports the current number of packets received since the		"Reports the current number of packets received since the
	beginning of the measure.		beginning of the measure.
	This parameters is useful to monitor the measure and it is needed		This parameters is useful to monitor the measure and it is needed
	to compute statistics."		to compute statistics."
	::= { ippmNetMeasureEntry 26 }		::= { ippmNetMeasureEntry 25 }
	ippmNetMeasureLastUpdate OBJECT-TYPE		ippmNetMeasureLastUpdate OBJECT-TYPE
	SYNTAX GMTTimeStamp		SYNTAX GMTTimeStamp
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The time when the last aggregation was computed."		"The time when the last aggregation was computed."
	::= { ippmNetMeasureEntry 27 }		::= { ippmNetMeasureEntry 26 }
	ippmNetMeasureOperState OBJECT-TYPE		ippmNetMeasureOperState OBJECT-TYPE
	SYNTAX INTEGER {		SYNTAX INTEGER {
	unknown(0),		unknown(0),
	running(1),		running(1),
	stopped(2)		stopped(2)
	}		}
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Reports the operational status of the network measure."		"Reports the operational status of the network measure."
	::= { ippmNetMeasureEntry 28 }		::= { ippmNetMeasureEntry 27 }
	--		--
	--		--
			-- ippmAggrMeasure Group
			--
			--
			--
			--
	-- ippmAggrMeasureTable		-- ippmAggrMeasureTable
	--		--
	--		--
	ippmAggrMeasureTable OBJECT-TYPE		ippmAggrMeasureTable OBJECT-TYPE
	SYNTAX SEQUENCE OF IppmAggrMeasureEntry		SYNTAX SEQUENCE OF IppmAggrMeasureEntry
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	" An aggregated measure summarizes the results of previous		"An aggregated measure summarizes the results of previous network
	network or aggregated measures. The results are saved in the		or aggregated measures. The results are saved in the
	ippmHistoryTable.		ippmHistoryTable.
	Each step of the calculation for the measure produces a singleton		Each step of the calculation for the measure produces a singleton
	result per metric."		result per metric."
	::= { ippmMeasure 2 }		::= { ippmAggrMeasure 1 }
	ippmAggrMeasureEntry OBJECT-TYPE		ippmAggrMeasureEntry OBJECT-TYPE
	SYNTAX IppmAggrMeasureEntry		SYNTAX IppmAggrMeasureEntry
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Typically, the configuration operation sets the value of		"Typically, the configuration operation creates and sets the
	theIppmAggrMeasureEntry.		value of the fields of a new ippmAggrMeasureEntry.
			ippmAggrMeasureOwner and ippmAggrMeasureIndex identify the
			instance created.
			The field ippmAggrMeasureMetrics identifies the metric to
			compute. As such its ippmMetricsType should be 'aggregated'.
	The ippmAggrMeasureMetrics defines the metric to compute.		The measure aggregates the results of a measure identified by
	The results of the measure to summarize are identified by:		ippmAggrMeasureHistoryOwner, ippmAggrMeasureHistoryIndex and
	+ ippmAggrMeasureOwner,		ippmAggrMeasureHistoryMetric. The measure to aggregate belongs to
	+ ippmAggrMeasureIndex		ippmNetMeasureTable or ippmAggrMeasureTable.
	The aggregated task starts at ippmAggrMeasureBeginTime and ends		The aggregation starts at ippmAggrMeasureBeginTime and ends after
	after ippmAggrMeasureDuration. An aggregated result is performed		ippmAggrMeasureDuration.
	and saved in the ippmHistoryTable for each
	ippmMeasureCollectionRate tick. "		An aggregated result is computed for each
			ippmMeasureCollectionRate tick and saved in the
			ippmHistoryTable."
	INDEX { ippmAggrMeasureOwner, ippmAggrMeasureIndex }		INDEX { ippmAggrMeasureOwner, ippmAggrMeasureIndex }
	::= { ippmAggrMeasureTable 1 }		::= { ippmAggrMeasureTable 1 }
	IppmAggrMeasureEntry ::= SEQUENCE {		IppmAggrMeasureEntry ::= SEQUENCE {
	ippmAggrMeasureOwner IppmOwnerString,		ippmAggrMeasureOwner IppmOwnerString,
	ippmAggrMeasureIndex Unsigned32,		ippmAggrMeasureIndex IppmOwnerIndex,
	ippmAggrMeasureName SnmpAdminString,		ippmAggrMeasureName SnmpAdminString,
	ippmAggrMeasureMetrics IppmStandardMetrics,		ippmAggrMeasureMetrics IppmStandardMetrics,
			ippmAggrMeasureHistoryOwner IppmOwnerString,
			ippmAggrMeasureHistoryIndex IppmOwnerIndex,
			ippmAggrMeasureHistoryMetric IppmMetricsRegistryIndex,
			ippmAggrMeasureFilter IppmMetricResultFilter,
			ippmAggrMeasureLowThreshold Unsigned32,
			ippmAggrMeasureHighThreshold Unsigned32,
	ippmAggrMeasureBeginTime GMTTimeStamp,		ippmAggrMeasureBeginTime GMTTimeStamp,
	ippmAggrMeasureAggrPeriodUnit TimeUnit,		ippmAggrMeasureAggrPeriodUnit TimeUnit,
	ippmAggrMeasureAggrPeriod Unsigned32,		ippmAggrMeasureAggrPeriod Unsigned32,
	ippmAggrMeasureDurationUnit TimeUnit,		ippmAggrMeasureDurationUnit TimeUnit,
	ippmAggrMeasureDuration Unsigned32,		ippmAggrMeasureDuration Unsigned32,
	ippmAggrMeasureHistorySize Unsigned32,		ippmAggrMeasureHistorySize Unsigned32,
	ippmAggrMeasureStorageType StorageType,		ippmAggrMeasureStorageType StorageType,
	ippmAggrMeasureHistoryOwner IppmOwnerString,
	ippmAggrMeasureHistoryOwnerIndex Unsigned32,
	ippmAggrMeasureHistoryMetric Unsigned32,
	ippmAggrMeasureAdminState INTEGER,		ippmAggrMeasureAdminState INTEGER,
	ippmAggrMeasureFastReport OBJECT IDENTIFIER,		ippmAggrMeasureFastReport OBJECT IDENTIFIER,
	ippmAggrMeasureMap SnmpAdminString,
	ippmAggrMeasureResultsMgmt INTEGER,		ippmAggrMeasureResultsMgmt INTEGER,
	ippmAggrMeasureLastUpdate GMTTimeStamp,		ippmAggrMeasureLastUpdate GMTTimeStamp,
	ippmAggrMeasureOperState INTEGER,		ippmAggrMeasureOperState INTEGER,
	ippmAggrMeasureNbPktsTreated Counter64,		ippmAggrMeasureNbPktsTreated Counter64,
	ippmAggrMeasureStatus RowStatus		ippmAggrMeasureStatus RowStatus
	}		}
	ippmAggrMeasureOwner OBJECT-TYPE		ippmAggrMeasureOwner OBJECT-TYPE
	SYNTAX IppmOwnerString		SYNTAX IppmOwnerString
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The owner who has configured this entry."		"The owner who has configured this entry."
	::= { ippmAggrMeasureEntry 1 }		::= { ippmAggrMeasureEntry 1 }
	ippmAggrMeasureIndex OBJECT-TYPE		ippmAggrMeasureIndex OBJECT-TYPE
	SYNTAX Unsigned32 (1.. 65535)		SYNTAX IppmOwnerIndex
	MAX-ACCESS not-accessible		MAX-ACCESS not-accessible
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The index of the aggregated measure. The value is managed by the		"The index of the aggregated measure. The value is managed by the
	owner."		owner."
	::= { ippmAggrMeasureEntry 2 }		::= { ippmAggrMeasureEntry 2 }
	ippmAggrMeasureName OBJECT-TYPE		ippmAggrMeasureName OBJECT-TYPE
	SYNTAX SnmpAdminString		SYNTAX SnmpAdminString
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The name of the instance of the metric. It illustrates the		"The name of the instance of the metric. It illustrates the
	specificity of the metric and includes the metric and the typeP.		specificity of the metric and includes the metric and the typeP.
	example: IP-port-HTTP-connectivity"		example: IP-port-HTTP-connectivity: free text."
	::= { ippmAggrMeasureEntry 3 }		::= { ippmAggrMeasureEntry 3 }
	ippmAggrMeasureMetrics OBJECT-TYPE		ippmAggrMeasureMetrics OBJECT-TYPE
	SYNTAX IppmStandardMetrics		SYNTAX IppmStandardMetrics
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Defines the metrics to compute within this aggregated measure.		"ippmAggrMeasureMetrics defines the metrics to compute within
			this aggregated measure.
	ONLY aggregated metrics of the same type are allowed in this		Only aggregated metrics of the same type are allowed in this
	field.		field (e.g. Measurement of minimum, average and maximum metrics
	A measure may be configured for the result of different metric		are generally processed simultaneously on the same network
	singletons to be archived in the ippmHistoryTable. The		measure).
	ippmMetricIndex of the created result has the value of the bit
	index of the corresponding ippmAggrMeasureMetrics as explained		Results are saved in the ippmHistoryTable. Results of a metric
	above in the ippmMetricIndex definition.		are identified using an index of type IppmMetricsRegistryIndex.
	Example:		Example:
	A network measure asking for One-way-Delay(6) and One-way-Packet-		Given a multi-aggregation of One-way-Delay-Median(9) and One-way-
	Loss(12) generated a flow of singletons which are logged in the		Delay-Minimum(10). The value of the field ippmAggrMeasureMetrics
	ippmHistoryTable. The singletons created for the One-way-Delay		is '0000011000000000'b, '0600'B. Results are logged in the
	measure have a value of ippmMetricIndex of 6.The aggregated		ippmHistoryTable where One-way-Delay-Median singletons have a
	measure definition(s) might be One-Way-Delay-Percentile(8),One-		value of ippmMetricsIndex of 9 while One-way-Delay-Minimum
	way-Delay-Median(9), or One-way-Delay-Minimum(10 .		singletons have a value of ippmMetricsIndex of 10.
			NOTE WELL: It is not recommended to use the multi aggregation
			capability in conjunction with the filter feature.
	"		"
	::= { ippmAggrMeasureEntry 4 }		::= { ippmAggrMeasureEntry 4 }
			ippmAggrMeasureHistoryOwner OBJECT-TYPE
			SYNTAX IppmOwnerString
			MAX-ACCESS read-create
			STATUS current
			DESCRIPTION
			"The owner of the measure to summarize. "
			::= { ippmAggrMeasureEntry 5 }
			ippmAggrMeasureHistoryIndex OBJECT-TYPE
			SYNTAX IppmOwnerIndex
			MAX-ACCESS read-create
			STATUS current
			DESCRIPTION
			"The owner index of the measure to summarize. "
			::= { ippmAggrMeasureEntry 6 }
			ippmAggrMeasureHistoryMetric OBJECT-TYPE
			SYNTAX IppmMetricsRegistryIndex
			MAX-ACCESS read-create
			STATUS current
			DESCRIPTION
			"The metric of the measure to summarize. "
			::= { ippmAggrMeasureEntry 7 }
			ippmAggrMeasureFilter OBJECT-TYPE
			SYNTAX IppmMetricResultFilter
			MAX-ACCESS read-create
			STATUS current
			DESCRIPTION
			"
			ippmAggrMeasureFilter defines the kind of filter to apply on a
			result to determine if the result is stored or not. The
			parameters of the filter are ippmAggrMeasureLowThreshold and
			ippmAggrMeasureHighThreshold.
			Thresholds have the same unit as the metric value.
			In the following examples we consider an aggregated measure. Its
			low threshold is set to 80.its high threshold is set to 100. The
			aggregation produced a flow of 12 aggregated results {40 30 60 85
			140 130 190 95 50 90 30 20}.
			If the filter is set to 'logInBandValue' then the results 85, 95,
			90 will be stored.
			If the filter is set to 'logOutBandValue' then the results 40 30
			60 140 130 190 50 30 20 will be stored.
			If the filter is set to 'logAboveValue' then the results 140 130
			190 will be stored.
			If the filter is set to 'logBelowValue' then the results 40 30 60
			50 30 20 will be stored.
			If the filter is set to 'logUpAndDownValue' then the results 40,
			140, 50 will be stored."
			::= { ippmAggrMeasureEntry 8 }
			ippmAggrMeasureLowThreshold OBJECT-TYPE
			SYNTAX Unsigned32
			MAX-ACCESS read-create
			STATUS current
			DESCRIPTION
			"An event is generated when the result of the measure of the
			metric is lower that the value of ippmAggrMeasureLowThreshold.
			The threshold has the same unit as the metric. The metric unit is
			recorded in the object ippmMetricsUnit of this metric entry in
			the ippmMetricsTable.
			"
			::= { ippmAggrMeasureEntry 9 }
			ippmAggrMeasureHighThreshold OBJECT-TYPE
			SYNTAX Unsigned32
			MAX-ACCESS read-create
			STATUS current
			DESCRIPTION
			"An event is generated when the result of the measure of the
			metric exceeds the value of ippmAggrMeasureHighThreshold.
			The threshold has the same unit as the metric. The metric unit is
			recorded in the object ippmMetricsUnit of this metric entry in
			the ippmMetricsTable.
			"
			::= { ippmAggrMeasureEntry 10 }
	ippmAggrMeasureBeginTime OBJECT-TYPE		ippmAggrMeasureBeginTime OBJECT-TYPE
	SYNTAX GMTTimeStamp		SYNTAX GMTTimeStamp
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Specifies the time at which the aggregated measure starts."		"Specifies the time at which the aggregated measure starts."
	::= { ippmAggrMeasureEntry 5 }		::= { ippmAggrMeasureEntry 11 }
	ippmAggrMeasureAggrPeriodUnit OBJECT-TYPE		ippmAggrMeasureAggrPeriodUnit OBJECT-TYPE
	SYNTAX TimeUnit		SYNTAX TimeUnit
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Specifies the unit of the aggregated measure period."		"Specifies the unit of the aggregated measure period."
	DEFVAL { second }		DEFVAL { second }
	::= { ippmAggrMeasureEntry 6 }		::= { ippmAggrMeasureEntry 12 }
	ippmAggrMeasureAggrPeriod OBJECT-TYPE		ippmAggrMeasureAggrPeriod OBJECT-TYPE
	SYNTAX Unsigned32		SYNTAX Unsigned32
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Specifies the amount of time between 2 measurement action		"Specifies the amount of time between 2 measurement action
	intervals. The action is specific to the semantic of the measure.		intervals. The action is specific to the semantic of the measure.
	Network metrics:		Network metrics:
	skipping to change at page 49, line 4		skipping to change at page 49, line 13
	Aggregated metrics:		Aggregated metrics:
	They are performed periodically on a sequence of results of other		They are performed periodically on a sequence of results of other
	measures. The period corresponds to the interval between two		measures. The period corresponds to the interval between two
	successive computations of the metric. The value of		successive computations of the metric. The value of
	ippmHistoryTimestamp result of a aggregated metric computed		ippmHistoryTimestamp result of a aggregated metric computed
	corresponds to the value of the ippmHistoryTimestamp of the last		corresponds to the value of the ippmHistoryTimestamp of the last
	metric result of the sequence used to compute the aggregated		metric result of the sequence used to compute the aggregated
	metric."		metric."
	DEFVAL { 60 }		DEFVAL { 60 }
	::= { ippmAggrMeasureEntry 7 }
			::= { ippmAggrMeasureEntry 13 }
	ippmAggrMeasureDurationUnit OBJECT-TYPE		ippmAggrMeasureDurationUnit OBJECT-TYPE
	SYNTAX TimeUnit		SYNTAX TimeUnit
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Specifies the unit of the measure duration."		"Specifies the unit of the measure duration."
	DEFVAL { second }		DEFVAL { second }
	::= { ippmAggrMeasureEntry 8 }		::= { ippmAggrMeasureEntry 14 }
	ippmAggrMeasureDuration OBJECT-TYPE		ippmAggrMeasureDuration OBJECT-TYPE
	SYNTAX Unsigned32		SYNTAX Unsigned32
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Specifies the duration of the measure."		"Specifies the duration of the measure."
	DEFVAL { 120 }		DEFVAL { 120 }
	::= { ippmAggrMeasureEntry 9 }		::= { ippmAggrMeasureEntry 15 }
	ippmAggrMeasureHistorySize OBJECT-TYPE		ippmAggrMeasureHistorySize OBJECT-TYPE
	SYNTAX Unsigned32		SYNTAX Unsigned32
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Specifies the maximum number of results saved for each metric of		"Specifies the maximum number of results saved for each metric of
	this measure. Overflow condition will be managed by the object		this measure. Overflow condition will be managed by the object
	ippmAggrMeasureResultsMgmt. "		ippmAggrMeasureResultsMgmt. "
	DEFVAL { 2 }		DEFVAL { 2 }
	::= { ippmAggrMeasureEntry 10 }		::= { ippmAggrMeasureEntry 16 }
	ippmAggrMeasureStorageType OBJECT-TYPE		ippmAggrMeasureStorageType OBJECT-TYPE
	SYNTAX StorageType		SYNTAX StorageType
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"This object defines whether this row and the measure controlled		"This object defines whether this row and the measure controlled
	by this row are kept in volatile storage and lost upon reboot or		by this row are kept in volatile storage and lost upon reboot or
	if this row is backed up		if this row is backed up
	by non-volatile or permanent storage.		by non-volatile or permanent storage.
	skipping to change at page 49, line 44		skipping to change at page 50, line 4
	ippmAggrMeasureStorageType OBJECT-TYPE		ippmAggrMeasureStorageType OBJECT-TYPE
	SYNTAX StorageType		SYNTAX StorageType
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"This object defines whether this row and the measure controlled		"This object defines whether this row and the measure controlled
	by this row are kept in volatile storage and lost upon reboot or		by this row are kept in volatile storage and lost upon reboot or
	if this row is backed up		if this row is backed up
	by non-volatile or permanent storage.		by non-volatile or permanent storage.
	Possible values are: other(1), volatile(2), nonVolatile(3),		Possible values are: other(1), volatile(2), nonVolatile(3),
	permanent(4), readOnly(5)."		permanent(4), readOnly(5)."
	DEFVAL { nonVolatile }		DEFVAL { nonVolatile }
	::= { ippmAggrMeasureEntry 11 }		::= { ippmAggrMeasureEntry 17 }
	ippmAggrMeasureResultsMgmt OBJECT-TYPE		ippmAggrMeasureResultsMgmt OBJECT-TYPE
	SYNTAX INTEGER {		SYNTAX INTEGER {
	wrap(1),		wrap(1),
	suspend(2)		suspend(2)
	}		}
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"This object displays the way the history of the aggregated		"This object displays the way the history of the aggregated
	measure is managed.		measure is managed.
	'wrap'		'wrap'
	continue the measure and erase the older entries in the		continue the measure and erase the older entries in the
	history.		history.
	'suspend'		'suspend'
	stop the measure and keep the results in the history.		stop the measure and keep the results in the history.
	"		"
	DEFVAL { wrap }		DEFVAL { wrap }
	::= { ippmAggrMeasureEntry 12 }		::= { ippmAggrMeasureEntry 18 }
	ippmAggrMeasureHistoryOwner OBJECT-TYPE
	SYNTAX IppmOwnerString
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"The owner of the measure to summarize. "
	::= { ippmAggrMeasureEntry 13 }
	ippmAggrMeasureHistoryOwnerIndex OBJECT-TYPE
	SYNTAX Unsigned32 (1.. 65535)
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"The owner index of the measure to summarize. "
	::= { ippmAggrMeasureEntry 14 }
	ippmAggrMeasureHistoryMetric OBJECT-TYPE
	SYNTAX Unsigned32 (1.. 65535)
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"The metric of the measure to summarize. "
	::= { ippmAggrMeasureEntry 15 }
	ippmAggrMeasureAdminState OBJECT-TYPE		ippmAggrMeasureAdminState OBJECT-TYPE
	SYNTAX INTEGER {		SYNTAX INTEGER {
	start(0),		start(0),
	stop(1)		stop(1)
	}		}
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"This object controls the activity of the aggregated measure.		"This object controls the activity of the aggregated measure.
	skipping to change at page 51, line 4		skipping to change at page 50, line 40
	SYNTAX INTEGER {		SYNTAX INTEGER {
	start(0),		start(0),
	stop(1)		stop(1)
	}		}
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"This object controls the activity of the aggregated measure.		"This object controls the activity of the aggregated measure.
	'start'		'start'
	The aggregated measure is started.		The aggregated measure is started.
	'stop'		'stop'
	The aggregated measure is stopped."		The aggregated measure is stopped."
	DEFVAL { start }		DEFVAL { start }
	::= { ippmAggrMeasureEntry 16 }		::= { ippmAggrMeasureEntry 19 }
	ippmAggrMeasureFastReport OBJECT-TYPE		ippmAggrMeasureFastReport OBJECT-TYPE
	SYNTAX OBJECT IDENTIFIER		SYNTAX OBJECT IDENTIFIER
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"A fast report is required in order to verify quickly that a		"A fast report is required in order to verify quickly that a
	measure is running well.		measure is running well.
	The feature 'fast report' is active if IppmAggrMeasureFastReport
			The feature 'fast report' is active if ippmAggrMeasureFastReport
	is not null and points to a notification.		is not null and points to a notification.
	A fast report consists of sending by email to the owner of the		A fast report consists of sending by email to the owner of the
	measure, a table of the results of all the metrics computed by		measure, a table of the results of all the metrics computed by
	this aggregated measure. The owner email address is read from the		this aggregated measure. The owner email address is read from the
	ippmOwnersTable.		ippmOwnersTable.
	ippmAggrMeasureFastReport identifies the notification which		ippmAggrMeasureFastReport identifies the notification which
	defines the header of the report.		defines the header of the report.
	The results part of the report is made of the a column of results		The results part of the report is made of a column of results per
	per metrics. Results are separated using commas.		metrics. Results are separated using commas.
	To avoid disaster, an aggregated measure using a fast report must		To avoid disaster, an aggregated measure using a fast report must
	have a cycle of aggregation greater than or equal to 1 second and		have a cycle of aggregation greater than or equal to 1 second and
	should not sent more than an email every 5 minutes and should not		should not sent more than an email every 5 minutes and should not
	sent more than 12 emails."		sent more than 12 emails."
	DEFVAL { zeroDotZero }		DEFVAL { zeroDotZero }
	::= { ippmAggrMeasureEntry 17 }		::= { ippmAggrMeasureEntry 20 }
	ippmAggrMeasureMap OBJECT-TYPE
	SYNTAX SnmpAdminString
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"This object allows for classification of the measure. It is
	typically the name of an administrative map.
	"
	DEFVAL { "" }
	::= { ippmAggrMeasureEntry 18 }
	ippmAggrMeasureLastUpdate OBJECT-TYPE		ippmAggrMeasureLastUpdate OBJECT-TYPE
	SYNTAX GMTTimeStamp		SYNTAX GMTTimeStamp
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The time when the last aggregated measure was computed."		"The time when the last aggregated measure was computed."
	::= { ippmAggrMeasureEntry 19 }		::= { ippmAggrMeasureEntry 21 }
	ippmAggrMeasureOperState OBJECT-TYPE		ippmAggrMeasureOperState OBJECT-TYPE
	SYNTAX INTEGER {		SYNTAX INTEGER {
	unknown(0),		unknown(0),
	running(1),		running(1),
	stopped(2)		stopped(2)
	}		}
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Reports the operational status of the aggregated measure."		"Reports the operational status of the aggregated measure."
	::= { ippmAggrMeasureEntry 20 }		::= { ippmAggrMeasureEntry 22 }
	ippmAggrMeasureNbPktsTreated OBJECT-TYPE		ippmAggrMeasureNbPktsTreated OBJECT-TYPE
	SYNTAX Counter64		SYNTAX Counter64
	UNITS "Packets"		UNITS "Packets"
	MAX-ACCESS read-only		MAX-ACCESS read-only
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"Reports the current number of packets used to calculate the		"Reports the current number of packets used to calculate the
	aggregation since the start of the measure.		aggregation since the start of the measure.
	This parameters is useful to monitor the measure and it is needed		This parameters is useful to monitor the measure and it is needed
	to compute statistics."		to compute statistics."
	::= { ippmAggrMeasureEntry 21 }		::= { ippmAggrMeasureEntry 23 }
	ippmAggrMeasureStatus OBJECT-TYPE		ippmAggrMeasureStatus OBJECT-TYPE
	SYNTAX RowStatus		SYNTAX RowStatus
	MAX-ACCESS read-create		MAX-ACCESS read-create
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The status of this table entry. Once the entry status is set to		"The status of this entry. Once the entry status is set to
	active, the associate entry cannot be modified.		active, the associate entry cannot be modified.
	"		"
	::= { ippmAggrMeasureEntry 22 }		::= { ippmAggrMeasureEntry 24 }
	ippmReportPathToResults OBJECT-TYPE
	SYNTAX SnmpAdminString
	MAX-ACCESS read-only
	STATUS current
	DESCRIPTION
	" It is typically a URL describing the file location where the
	results are logged. "
	::= { ippmReport 1 }
	ippmReportSetupTable OBJECT-TYPE
	SYNTAX SEQUENCE OF IppmReportSetupEntry
	MAX-ACCESS not-accessible
	STATUS current
	DESCRIPTION
	"The ippmReportSetupTable is a list of definition of reports. It
	defines the results of network and/or aggregated measures that
	are to be reported. A report is saved in the ippmReportTable, or
	sent to an application using an SNMP Trap, an SNMP inform PDU, an
	email, or a SMS. The reporting task is not intended to be a batch
	action processed at the end of the measure. It is coupled with
	threshold detections and event filtering to deliver application
	level events and data, while preserving scalability.
	"
	::= { ippmReport 2 }
	ippmReportSetupEntry OBJECT-TYPE
	SYNTAX IppmReportSetupEntry
	MAX-ACCESS not-accessible
	STATUS current
	DESCRIPTION
	"The report applies to the results of a measure as defined in
	either the network measure table, or the aggregated measure
	table.
	The ippmReportSetupDefinition describes the data and the events
	to include in the report. The definition consists of a list of
	tasks to perform on the results of the measure.
	A report is associated to a network measure or to an aggregated
	measure.
	Note 1: To associate a report to an existing measure the manager
	suspends the measure by setting either the
	ippmAggrMeasureAdminStatus or the ippmAggrMeasureStatus to
	'notInService'. Then one sets the report fields and activates the
	measure by setting the corresponding MeasureStatus to 'active'.
	Note 2: A report is tied to a measure and its period."
	INDEX { ippmReportSetupOwner, ippmReportSetupIndex }
	::= { ippmReportSetupTable 1 }
	IppmReportSetupEntry ::=
	SEQUENCE {
	ippmReportSetupOwner IppmOwnerString,
	ippmReportSetupIndex Unsigned32,
	ippmReportSetupMeasureOwner IppmOwnerString,
	ippmReportSetupMeasureIndex Unsigned32,
	ippmReportSetupMeasureMetric Unsigned32,
	ippmReportSetupDefinition IppmReportDefinition,
	ippmReportSetupUpDownThreshold Unsigned32,
	ippmReportSetupLowThreshold Unsigned32,
	ippmReportSetupHighThreshold Unsigned32,
	ippmReportSetupDurationThresUnit TimeUnit,
	ippmReportSetupDurationThreshold Unsigned32,
	ippmReportSetupReportSize Unsigned32,
	ippmReportSetupResultsMgmt INTEGER,
	ippmReportSetupNMS IppmOwnerString,
	ippmReportSetupNotification OBJECT IDENTIFIER,
	ippmReportSetupMap SnmpAdminString,
	ippmReportSetupStatus RowStatus
	}
	ippmReportSetupOwner OBJECT-TYPE
	SYNTAX IppmOwnerString
	MAX-ACCESS not-accessible
	STATUS current
	DESCRIPTION
	"The owner who has configured this report entry."
	::= { ippmReportSetupEntry 1 }
	ippmReportSetupIndex OBJECT-TYPE
	SYNTAX Unsigned32 (1.. 65535)
	MAX-ACCESS not-accessible
	STATUS current
	DESCRIPTION
	"The owner index of the report entry. The value is managed by the
	owner."
	::= { ippmReportSetupEntry 2 }
	ippmReportSetupMeasureOwner OBJECT-TYPE
	SYNTAX IppmOwnerString
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"The owner of the measure to report."
	::= { ippmReportSetupEntry 3 }
	ippmReportSetupMeasureIndex OBJECT-TYPE
	SYNTAX Unsigned32 (1.. 65535)
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"The index of the measure to report."
	::= { ippmReportSetupEntry 4 }
	ippmReportSetupMeasureMetric OBJECT-TYPE
	SYNTAX Unsigned32 (1.. 65535)
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"The metric of the measure to report."
	::= { ippmReportSetupEntry 5 }
	ippmReportSetupDefinition OBJECT-TYPE
	SYNTAX IppmReportDefinition
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"In order to properly define a report, one must provide
	information to:
	+ Select the events to consider for reporting
	+ Configure filters to select pertinent values
	+ Describe the way the report is delivered
	+ Describe clean up actions to perform on report completion
	The format of a report sent to a NMS is described in a
	notification defined in the ippmNotifications node.
	The event and the filter selected in the report definition
	determine the notification:
	+ Up and Down filter report format is ippmUpAndDownReport;
	+ Inband filter report format is ippmInBandReport;
	+ Outband filter report format is ippmOutBandReport;
	+ Above filter report format is ippmAboveReport;
	+ Below filter report format is ippmBelowReport;
	+ Any filter and reportExceededEventsDuration report format is
	ippmEventsDurationExceededReport;
	+ Any filter and the event onMeasureCompletion report format is
	ippmCompletedMeasureReport;
	Example 1:
	Consider a report definition, which reports up and down result
	events of a metric measure:
	ippmReportSetupDefinition {
	onSingleton,
	reportUpAndDownMetricResults,
	inSNMPv2TrapPDU
	}
	The value of the threshold is given by
	ippmReportSetupUpDownThreshold. It has the value '5' in this
	example.
	Being a flow of results { 3.3 3.2 3.2 5.1 5.3 5.6 6.3 5.2 4.0 3.8
	...}, the report process will send 2 traps:
	+ The first one carries the result 5.1 corresponding to
	a down to up event;
	+ The second one carries the result 4.0 of the up to
	down event
	Example 2:
	Consider the report definition, which reports per measure cycle
	in a SNMP informRequestPDU, up and down results events of a
	metric measure:
	:
	ippmReportSetupDefinition {
	onMeasureCycle,
	reportUpAndDownMetricResults,
	inInformRequestPDU
	}
	The value of the threshold is given by
	ippmReportSetupUpDownThreshold. It has the value '5' in this
	example.
	The cycle of measure of the measure setup is set to 10 results.
	Being a flow of 10 results { 3.3 3.2 3.2 5.1 5.3 5.6 6.3 5.2 4.0
	3.8 ... }, the report process will send one InformRequestPDU that
	carries 5.1 and 4.0 corresponding to the first down to up event
	and to the second up to down event, respectively. "
	::= { ippmReportSetupEntry 6 }
	ippmReportSetupUpDownThreshold OBJECT-TYPE
	SYNTAX Unsigned32
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"An event is generated when the result of the measure exceeds the
	value of ippmReportSetupMetricThreshold, and then goes below the
	threshold or vice versa. In the case of being over the threshold,
	and then being below it, the measure value that is immediately
	below the threshold, after previously being above it, is
	reported. In the case of being below the threshold and then being
	above it, the measure value that is above the threshold is
	reported.
	The threshold has the same unit as the metric. The metric unit is
	recorded in the object ippmMetricsUnit of this metric entry in
	the ippmMetricTable.
	"
	::= { ippmReportSetupEntry 7 }
	ippmReportSetupLowThreshold OBJECT-TYPE
	SYNTAX Unsigned32
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"An event is generated when the result of the measure of the
	metric is lower that the value of ippmReportSetupLowThreshold.
	The threshold has the same unit as the metric. The metric unit is
	recorded in the object ippmMetricsUnit of this metric entry in
	the ippmMetricTable.
	"
	::= { ippmReportSetupEntry 8 }
	ippmReportSetupHighThreshold OBJECT-TYPE
	SYNTAX Unsigned32
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"An event is generated when the result of the measure of the
	metric exceeds the value of ippmReportSetupHighThreshold.
	The threshold has the same unit as the metric. The metric unit is
	recorded in the object ippmMetricsUnit of this metric entry in
	the ippmMetricTable.
	"
	::= { ippmReportSetupEntry 9 }
	ippmReportSetupDurationThresUnit OBJECT-TYPE
	SYNTAX TimeUnit
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"The unit of the duration threshold."
	DEFVAL { second }
	::= { ippmReportSetupEntry 10 }
	ippmReportSetupDurationThreshold OBJECT-TYPE
	SYNTAX Unsigned32
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"An event is generated when contiguous results of the measure are
	over the ippmReportSetupUpDownThreshold, during
	ippmReportSetupDurationThreshold seconds.
	Performance:
	To improve the performance of the system, the report process may
	be synchronized with the cycle of collection of network measures,
	or with the period of aggregation of an aggregated measure."
	DEFVAL { 15 }
	::= { ippmReportSetupEntry 11 }
	ippmReportSetupReportSize OBJECT-TYPE
	SYNTAX Unsigned32
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"Specifies the maximum number of results saved for each metric of
	this measure. The history of each metric is managed as a circular
	table. The newest result overwrites the oldest one when the
	history granted to this metric measure is full.
	The management of the results may be optimized if synchronized
	with the reports steps of this measure. "
	::= { ippmReportSetupEntry 12 }
	ippmReportSetupResultsMgmt OBJECT-TYPE
	SYNTAX INTEGER {
	wrap(1),
	suspend(2)
	}
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"
	Action to take when the report log is full. The user may choose
	to either wrap, in which case the agent writes over existing
	records. The user may choose to suspend writing to the log in the
	event that he wishes to archive the data. The resume action
	causes the agent to begin to write in the report log, and assumes
	the data has been cleared
	This object indicates the way the measure results are managed
	when the owner quota is over:
	'wrap'
	continue the measure and erase the older entries in the
	history.
	'suspend'
	stop the measure and keep the results in the history"
	DEFVAL { wrap }
	::= { ippmReportSetupEntry 13 }
	ippmReportSetupNMS OBJECT-TYPE
	SYNTAX IppmOwnerString
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"The recipient of the report may be provided in the setup. By
	default the recipient of the report is the owner of the measure.
	Its addresses are recorded in the ippmOwnersTable.
	The type of ippmReportSetupNMS is not InetAddress because the
	report may be sent using SMS or fax.
	"
	DEFVAL { "" }
	::= { ippmReportSetupEntry 14 }
	ippmReportSetupNotification OBJECT-TYPE
	SYNTAX OBJECT IDENTIFIER
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"Even though the notification to use is defined in the report
	definition, the object ippmReportSetupNotification provides
	flexibility to select another notification. "
	DEFVAL { zeroDotZero }
	::= { ippmReportSetupEntry 15 }
	ippmReportSetupMap OBJECT-TYPE
	SYNTAX SnmpAdminString
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"An administrative name of a map to which the report belongs."
	DEFVAL { "" }
	::= { ippmReportSetupEntry 16 }
	ippmReportSetupStatus OBJECT-TYPE
	SYNTAX RowStatus
	MAX-ACCESS read-create
	STATUS current
	DESCRIPTION
	"The status of this table entry. "
	::= { ippmReportSetupEntry 17 }
	ippmReportTable OBJECT-TYPE
	SYNTAX SEQUENCE OF IppmReportEntry
	MAX-ACCESS not-accessible
	STATUS current
	DESCRIPTION
	"The ippmReportTable logs the results of the reports. The results
	consist of a subset of the results of a measure as described in
	the report definition. The activation of an up and down filtering
	in the report definition limits the results logged to those
	corresponding to major events. Otherwise, the ippmReportTable is
	identical to the ippmHistoryTable."
	::= { ippmReport 3 }
	ippmReportEntry OBJECT-TYPE
	SYNTAX IppmReportEntry
	MAX-ACCESS not-accessible
	STATUS current
	DESCRIPTION
	"A report is a list of results of a measure. This sample is
	associated with the ippmReportSetupEntry which has set up the
	report. An ippmReportEntry entry is one of the results of a
	measure to report.
	An ippmReportEntry entry is one of the results of a measure
	identified by ippmReportMeasureOwner, ippmReportMeasureIndex,
	ippmReportMetricIndex and ippmReportIndex.
	In the index:
	+ ippmReportSetupOwner identifies the owner of the measure
	+ ippmReportSetupIndex identifies the measure in the owner
	namespace;
	+ ippmReportSequence identifies the sequence number of the
	measure result"
	INDEX { ippmReportSetupOwner, ippmReportSetupIndex,
	ippmReportSequence }
	::= { ippmReportTable 1 }
	IppmReportEntry ::=
	SEQUENCE {
	ippmReportSequence Unsigned32,
	ippmReportTimestamp GMTTimeStamp,
	ippmReportValue Integer32
	}
	ippmReportSequence OBJECT-TYPE
	SYNTAX Unsigned32 (0..4294967295)
	MAX-ACCESS not-accessible
	STATUS current
	DESCRIPTION
	"ippmReportSequence is the sequence number of the measurement
	results to report.
	Network metrics:
	It's the sequence number of a measurement packet. Typically, it
	identifies the order of the packet in the stream of packets sends
	by the source.
	Aggregated metrics:
	It is the sequence number of the aggregated metric results
	computed."
	::= { ippmReportEntry 1 }
	ippmReportTimestamp OBJECT-TYPE
	SYNTAX GMTTimeStamp
	MAX-ACCESS read-only
	STATUS current
	DESCRIPTION
	"The timestamp of the measurement result."
	::= { ippmReportEntry 2 }
	ippmReportValue OBJECT-TYPE
	SYNTAX Integer32
	MAX-ACCESS read-only
	STATUS current
	DESCRIPTION
	"The value."
	::= { ippmReportEntry 3 }
	--		--
	-- IPPM Notifications		-- IPPM Notifications
	--		--
	ippmUpAndDownReport NOTIFICATION-TYPE		ippmAggrMeasureReport NOTIFICATION-TYPE
	OBJECTS {
	ippmReportSetupDefinition,
	ippmReportSetupUpDownThreshold,
	ippmMetricType,
	ippmMetricUnit,
	ippmMetricDescription,
	ippmHistoryTimestamp,
	ippmHistoryValue,
	ippmReportPathToResults
	}
	STATUS current
	DESCRIPTION
	"A notification sent because 2 contiguous results are on opposite
	sides of the metric threshold value.
	The notification contains the instances of the ippmHistoryValue
	object that exceeded the threshold in the case of a down to up
	change. In the case of a up to down change, the ippmHistoryValue
	object that is below the threshold immediately after being over
	the threshold.
	The notification contains the instances of the
	ippmHistoryTimestamp identifying the time the event occurred.
	ippmReportPathToResults is a link to the file name, which
	contains detailed results corresponding to this event."
	::= { ippmNotifications 1 }
	ippmInBandReport NOTIFICATION-TYPE
	OBJECTS {		OBJECTS {
	ippmReportSetupDefinition,		ippmAggrMeasureFilter,
	ippmReportSetupLowThreshold,		ippmAggrMeasureLowThreshold,
	ippmReportSetupHighThreshold,		ippmAggrMeasureHighThreshold,
	ippmMetricType,		ippmMetricsType,
	ippmMetricUnit,		ippmMetricsUnit,
	ippmMetricDescription,		ippmMetricsDescription,
	ippmHistoryTimestamp,		ippmHistoryTimestamp,
	ippmHistoryValue,		ippmHistoryValue,
	ippmReportPathToResults		ippmHistoryPathToResults
	}		}
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"A notification sent because the value of the measure is under		"A notification sent because the value of the measure is under
	the high threshold value and greater than the low threshold		the high threshold value and greater than the low threshold
	value.		value.
	The notification contains the instances of the ippmHistoryValue		The notification contains the instances of the ippmHistoryValue
	object that exceeded the threshold.		object that exceeded the threshold.
	The notification contains the instances of the		The notification contains the instances of the
	ippmHistoryTimestamp identifying the time the event occurred.		ippmHistoryTimestamp identifying the time the event occurred.
	ippmReportPathToResults is a link to the file name, which		ippmHistoryPathToResults is a link to the file name, which
	contains detailed results corresponding to this event."
	::= { ippmNotifications 2 }
	ippmOutBandReport NOTIFICATION-TYPE
	OBJECTS {
	ippmReportSetupDefinition,
	ippmReportSetupLowThreshold,
	ippmReportSetupHighThreshold,
	ippmMetricType,
	ippmMetricUnit,
	ippmMetricDescription,
	ippmHistoryTimestamp,
	ippmHistoryValue,
	ippmReportPathToResults
	}
	STATUS current
	DESCRIPTION
	"A notification sent because the result of the measure is either
	greater than the high threshold or lower than the low threshold.
	The notification contains the instances of the ippmHistoryValue
	object that exceeded the threshold.
	The notification contains the instances of the
	ippmHistoryTimestamp identifying the time the event occurred.
	ippmReportPathToResults is a link to the file name, which
	contains detailed results corresponding to this event."
	::= { ippmNotifications 3 }
	ippmAboveReport NOTIFICATION-TYPE
	OBJECTS {
	ippmReportSetupDefinition,
	ippmReportSetupHighThreshold,
	ippmMetricType,
	ippmMetricUnit,
	ippmMetricDescription,
	ippmHistoryTimestamp,
	ippmHistoryValue,
	ippmReportPathToResults
	}
	STATUS current
	DESCRIPTION
	"The notification contains the instances of the ippmHistoryValue
	object that exceeded the threshold.
	The notification contains the instances of the
	ippmHistoryTimestamp identifying the time the event occurred.
	ippmReportPathToResults is a link to the file name, which
	contains detailed results corresponding to this event."
	::= { ippmNotifications 4 }
	ippmBelowReport NOTIFICATION-TYPE
	OBJECTS {
	ippmReportSetupDefinition,
	ippmReportSetupLowThreshold,
	ippmMetricType,
	ippmMetricUnit,
	ippmMetricDescription,
	ippmHistoryTimestamp,
	ippmHistoryValue,
	ippmReportPathToResults
	}
	STATUS current
	DESCRIPTION
	"
	The notification contains the instances of the ippmHistoryValue
	object that were below the threshold.
	The notification contains the instances of the
	ippmHistoryTimestamp identifying the time the event occurred.
	ippmReportPathToResults is a link to the file name, which
	contains detailed results corresponding to this event."		contains detailed results corresponding to this event."
	::= { ippmNotifications 5 }		::= { ippmNotifications 1 }
	ippmEventsDurationExceededReport NOTIFICATION-TYPE
	OBJECTS {
	ippmReportSetupDefinition,
	ippmReportSetupUpDownThreshold,
	ippmReportSetupDurationThreshold,
	ippmReportSetupDurationThresUnit,
	ippmMetricType,
	ippmMetricUnit,
	ippmMetricDescription,
	ippmHistoryTimestamp,
	ippmHistoryValue,
	ippmReportPathToResults
	}
	STATUS current
	DESCRIPTION
	"A notification sent when the duration of continuously rising
	metric threshold exceeds the ippmReportSetupDurationThreshold
	value.
	The notification contains the instances of the ippmReportValue
	object that exceeded the threshold.
	The notification contains the instances of the
	ippmReportTimestamp identifying the time the event occurred.
	ippmReportPathToResults is a link to the file name, which
	contains detailed results corresponding to this event.
	"
	::= { ippmNotifications 6 }
	ippmCompletedMeasureReport NOTIFICATION-TYPE
	OBJECTS {
	ippmReportSetupDefinition,
	ippmMetricType,
	ippmMetricUnit,
	ippmMetricDescription,
	ippmHistoryTimestamp,
	ippmHistoryValue,
	ippmReportPathToResults
	}
	STATUS current
	DESCRIPTION
	"A notification sent when a measure completes.
	The index of the included ippmReportSetupDefinition object
	identifies the ippmMeasureEntry and the ippmResultSetupEntry that
	specified the report.
	ippmReportPathToResults is a link to the file name, which
	contains the results of this measure cycle."
	::= { ippmNotifications 7 }
	ippmAggrMeasureHistoryFull NOTIFICATION-TYPE		ippmAggrMeasureHistoryFull NOTIFICATION-TYPE
	OBJECTS {		OBJECTS {
	ippmAggrMeasureName,		ippmAggrMeasureName,
	ippmAggrMeasureHistorySize,		ippmAggrMeasureHistorySize,
	ippmMetricType,		ippmMetricsType,
	ippmMetricUnit,		ippmMetricsUnit,
	ippmMetricDescription,		ippmMetricsDescription,
	ippmHistoryTimestamp,		ippmHistoryTimestamp,
	ippmHistoryValue		ippmHistoryValue
	}		}
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	" A notification sent when the size of the history of a metric of		" A notification sent when the size of the history of a metric of
	a aggregated measure exceeds ippmAggrMeasureHistorySize. The		a aggregated measure exceeds ippmAggrMeasureHistorySize. The
	agent will then manage the reports according to the policy		agent will then manage the reports according to the policy
	described in ippmAggrMeasureResultsMgmt."		described in ippmAggrMeasureResultsMgmt."
	::= { ippmNotifications 8 }		::= { ippmNotifications 2 }
	ippmNetMeasureHistoryFull NOTIFICATION-TYPE		ippmNetMeasureHistoryFull NOTIFICATION-TYPE
	OBJECTS {		OBJECTS {
	ippmNetMeasureName,		ippmNetMeasureName,
	ippmNetMeasureHistorySize,		ippmNetMeasureHistorySize,
	ippmMetricType,		ippmMetricsType,
	ippmMetricUnit,		ippmMetricsUnit,
	ippmMetricDescription,		ippmMetricsDescription,
	ippmHistoryTimestamp,		ippmHistoryTimestamp,
	ippmHistoryValue		ippmHistoryValue
	}		}
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	" A notification sent when the size of the history of a metric of		" A notification sent when the size of the history of a metric of
	a network measure exceeded ippmNetMeasureHistorySize. Then the		a network measure exceeded ippmNetMeasureHistorySize. Then the
	agent manages the records according to the policy described in		agent manages the records according to the policy described in
	ippmNetMeasureResultsMgmt."		ippmNetMeasureResultsMgmt."
	::= { ippmNotifications 9 }		::= { ippmNotifications 3 }
	ippmReportLogFull NOTIFICATION-TYPE
	OBJECTS {
	ippmReportSetupResultsMgmt,
	ippmReportSetupReportSize,
	ippmReportTimestamp,
	ippmReportValue
	}
	STATUS current
	DESCRIPTION
	"A notification sent when the size of the report of a metric of a
	measure exceeded ippmReportSetupReportSize. The agent manages the
	reports according to the policy described in
	ippmReportSetupResultsMgmt."
	::= { ippmNotifications 10 }
	--		--
	-- IPPM MIB Conformance statements		-- IPPM MIB Conformance statements
	--		--
	ippmCompliances OBJECT IDENTIFIER ::={ ippmConformance 1 }		ippmCompliances OBJECT IDENTIFIER ::={ ippmConformance 1 }
	ippmGroups OBJECT IDENTIFIER ::={ ippmConformance 2 }		ippmGroups OBJECT IDENTIFIER ::={ ippmConformance 2 }
	ippmProxyInterDomainCompliances MODULE-COMPLIANCE		ippmProxyInterDomainCompliances MODULE-COMPLIANCE
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The compliance statement for SNMP entities which implement the		"The compliance statement for SNMP entities which implement the
	IPPM MIB as a proxy in interdomain. The implementation of the		IPPM MIB as a proxy in interdomain. The implementation of the
	VACM control is mandatory."		VACM control is mandatory."
	MODULE -- this module		MODULE -- this module
	MANDATORY-GROUPS {		MANDATORY-GROUPS {
	ippmSystemGroup, ippmNetMeasureGroup, ippmHistoryGroup,		ippmSystemGroup, ippmHistoryGroup, ippmNetMeasureGroup,
	ippmAggrMeasureGroup, ippmReportGroup, ippmNotificationGroup		ippmAggrMeasureGroup, ippmNotificationGroup
	}		}
	::= { ippmCompliances 1 }		::= { ippmCompliances 1 }
	ippmProxyCompliances MODULE-COMPLIANCE		ippmProxyCompliances MODULE-COMPLIANCE
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The compliance statement for SNMP entities which implement the		"The compliance statement for SNMP entities which implement the
	IPPM MIB as a proxy."		IPPM MIB as a proxy."
	MODULE -- this module		MODULE -- this module
	MANDATORY-GROUPS {		MANDATORY-GROUPS {
	ippmSystemGroup, ippmNetMeasureGroup, ippmHistoryGroup,		ippmSystemGroup, ippmOwnersGroup, ippmHistoryGroup,
	ippmAggrMeasureGroup, ippmReportGroup, ippmNotificationGroup		ippmNetMeasureGroup, ippmAggrMeasureGroup, ippmNotificationGroup
	}		}
	GROUP ippmOwnersGroup		GROUP ippmOwnersGroup
	DESCRIPTION		DESCRIPTION
	"The ippmOwnersGroup is needed if VACM is not implemented."		"The ippmOwnersGroup is needed if VACM is not implemented."
	::= { ippmCompliances 2 }		::= { ippmCompliances 2 }
	ippmProbeCompliances MODULE-COMPLIANCE		ippmEmbeddedCompliances MODULE-COMPLIANCE
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The compliance statement for SNMP entities which implement the		"The compliance statement for SNMP entities which implement the
	IPPM MIB in a probe."		IPPM MIB in a probe."
	MODULE -- this module		MODULE -- this module
	MANDATORY-GROUPS {		MANDATORY-GROUPS {
	ippmSystemGroup, ippmNetMeasureGroup, ippmHistoryGroup		ippmSystemGroup, ippmHistoryGroup, ippmNetMeasureGroup
	}		}
	::= { ippmCompliances 3 }		::= { ippmCompliances 3 }
	ippmSystemGroup OBJECT-GROUP		ippmSystemGroup OBJECT-GROUP
	OBJECTS {		OBJECTS {
	ippmSystemSynchronizationDesc,		ippmSystemSynchronizationDesc,
	ippmSystemTime,		ippmSystemTime,
	ippmSystemSynchronizationType,		ippmSystemSynchronizationType,
	ippmSystemClockResolution,		ippmSystemClockResolution,
	ippmSynchronizationTime,		ippmSynchronizationTime,
	ippmSynchronizationStratum,		ippmSynchronizationStratum,
	ippmSynchronizationResolution,		ippmSynchronizationResolution,
	ippmPointOfMeasureMgmtAddrType,		ippmPointOfMeasureMgmtAddrType,
	ippmPointOfMeasureMgmtAddress,		ippmPointOfMeasureMgmtAddress,
	ippmPointOfMeasureTestAddrTypeP,		ippmPointOfMeasureTestAddrType,
	ippmPointOfMeasureTestAddr,		ippmPointOfMeasureTestAddress,
	ippmSystemOperationalStatus,		ippmSystemOperationalStatus,
			ippmSystemAggregatedMetrics,
	ippmPointOfMeasureMetrics,		ippmPointOfMeasureMetrics,
	ippmMetricCapabilities,		ippmMetricsType,
	ippmMetricType,		ippmMetricsUnit,
	ippmMetricUnit,		ippmMetricsDescription
	ippmMetricDescription
	}		}
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The IPPM System Group"		"The IPPM System Group"
	::= { ippmGroups 1}		::= { ippmGroups 1}
	ippmNetMeasureGroup OBJECT-GROUP		ippmNetMeasureGroup OBJECT-GROUP
	OBJECTS {		OBJECTS {
	ippmNetMeasureName,		ippmNetMeasureName,
	ippmNetMeasureMetrics,		ippmNetMeasureMetrics,
	ippmNetMeasureBeginTime,		ippmNetMeasureBeginTime,
	ippmNetMeasureCollectionRateUnit,		ippmNetMeasureCollectionRateUnit,
	ippmNetMeasureCollectionRate,		ippmNetMeasureCollectionRate,
	ippmNetMeasureDurationUnit,		ippmNetMeasureDurationUnit,
	ippmNetMeasureDuration,		ippmNetMeasureDuration,
	ippmNetMeasureHistorySize,		ippmNetMeasureHistorySize,
	ippmNetMeasureFailureMgmtMode,		ippmNetMeasureFailureMgmtMode,
	ippmNetMeasureResultsMgmt,		ippmNetMeasureResultsMgmt,
	ippmNetMeasureSrcTypeP,		ippmNetMeasureSrcPacketType,
	ippmNetMeasureSrc,		ippmNetMeasureSrc,
	ippmNetMeasureDstTypeP,		ippmNetMeasureDstPacketType,
	ippmNetMeasureDst,		ippmNetMeasureDst,
	ippmNetMeasureTxMode,		ippmNetMeasureTxMode,
	ippmNetMeasureTxPacketRateUnit,		ippmNetMeasureTxPacketRateUnit,
	ippmNetMeasureTxPacketRate,		ippmNetMeasureTxPacketRate,
	ippmNetMeasureMedOrBurstSize,		ippmNetMeasureMedOrBurstSize,
	ippmNetMeasureDevOrIntBurstSize,		ippmNetMeasureDevOrIntBurstSize,
	ippmNetMeasureLossTimeout,		ippmNetMeasureLossTimeout,
	ippmNetMeasureL3PacketSize,		ippmNetMeasureL3PacketSize,
	ippmNetMeasureDataPattern,		ippmNetMeasureDataPattern,
	ippmNetMeasureMap,
	ippmNetMeasureTotalPktsRecv,		ippmNetMeasureTotalPktsRecv,
	ippmNetMeasureLastUpdate,		ippmNetMeasureLastUpdate,
	ippmNetMeasureOperState		ippmNetMeasureOperState
	}		}
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The IPPM Network Measure Group"		"The IPPM Network Measure Group"
	::= { ippmGroups 3}		::= { ippmGroups 2}
	ippmHistoryGroup OBJECT-GROUP		ippmHistoryGroup OBJECT-GROUP
	OBJECTS {		OBJECTS {
	ippmHistoryTimestamp,		ippmHistoryTimestamp,
	ippmHistoryValue		ippmHistoryValue,
			ippmHistoryPathToResults
	}		}
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The IPPM History Group"		"The IPPM History Group"
	::= { ippmGroups 4}		::= { ippmGroups 3}
	ippmAggrMeasureGroup OBJECT-GROUP		ippmAggrMeasureGroup OBJECT-GROUP
	OBJECTS {		OBJECTS {
	ippmAggrMeasureName,		ippmAggrMeasureName,
	ippmAggrMeasureMetrics,		ippmAggrMeasureMetrics,
	ippmAggrMeasureBeginTime,		ippmAggrMeasureBeginTime,
	ippmAggrMeasureAggrPeriodUnit,		ippmAggrMeasureAggrPeriodUnit,
	ippmAggrMeasureAggrPeriod,		ippmAggrMeasureAggrPeriod,
	ippmAggrMeasureDurationUnit,		ippmAggrMeasureDurationUnit,
	ippmAggrMeasureDuration,		ippmAggrMeasureDuration,
			ippmAggrMeasureFilter,
			ippmAggrMeasureLowThreshold,
			ippmAggrMeasureHighThreshold,
	ippmAggrMeasureHistorySize,		ippmAggrMeasureHistorySize,
	ippmAggrMeasureStorageType,		ippmAggrMeasureStorageType,
	ippmAggrMeasureHistoryOwner,		ippmAggrMeasureHistoryOwner,
	ippmAggrMeasureHistoryOwnerIndex,		ippmAggrMeasureHistoryIndex,
	ippmAggrMeasureHistoryMetric,		ippmAggrMeasureHistoryMetric,
	ippmAggrMeasureAdminState,		ippmAggrMeasureAdminState,
	ippmAggrMeasureFastReport,		ippmAggrMeasureFastReport,
	ippmAggrMeasureMap,
	ippmAggrMeasureResultsMgmt,		ippmAggrMeasureResultsMgmt,
	ippmAggrMeasureLastUpdate,		ippmAggrMeasureLastUpdate,
	ippmAggrMeasureOperState,		ippmAggrMeasureOperState,
	ippmAggrMeasureNbPktsTreated,		ippmAggrMeasureNbPktsTreated,
	ippmAggrMeasureStatus		ippmAggrMeasureStatus
	}		}
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The IPPM AggregatedMeasure Group"		"The IPPM AggregatedMeasure Group"
	::= { ippmGroups 5}		::= { ippmGroups 4}
	ippmReportGroup OBJECT-GROUP
	OBJECTS {
	ippmReportSetupMeasureOwner,
	ippmReportSetupMeasureIndex,
	ippmReportSetupMeasureMetric,
	ippmReportSetupDefinition,
	ippmReportSetupUpDownThreshold,
	ippmReportSetupLowThreshold,
	ippmReportSetupHighThreshold,
	ippmReportSetupDurationThresUnit,
	ippmReportSetupDurationThreshold,
	ippmReportSetupReportSize,
	ippmReportSetupResultsMgmt,
	ippmReportSetupNMS,
	ippmReportSetupNotification,
	ippmReportSetupMap,
	ippmReportSetupStatus,
	ippmReportPathToResults,
	ippmReportTimestamp,
	ippmReportValue
	}
	STATUS current
	DESCRIPTION
	"The IPPM Report Group"
	::= { ippmGroups 6}
	ippmOwnersGroup OBJECT-GROUP		ippmOwnersGroup OBJECT-GROUP
	OBJECTS {		OBJECTS {
	ippmOwnersOwner,
	ippmOwnersGrantedMetrics,		ippmOwnersGrantedMetrics,
	ippmOwnersQuota,		ippmOwnersQuota,
	ippmOwnersIpAddressType,		ippmOwnersIpAddressType,
	ippmOwnersIpAddress,		ippmOwnersIpAddress,
	ippmOwnersEmail,		ippmOwnersEmail,
	ippmOwnersSMS,
	ippmOwnersStatus		ippmOwnersStatus
	}		}
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The IPPM Owners Group"		"The IPPM Owners Group"
	::= { ippmGroups 7}		::= { ippmGroups 5}
	ippmNotificationGroup NOTIFICATION-GROUP		ippmNotificationGroup NOTIFICATION-GROUP
	NOTIFICATIONS {		NOTIFICATIONS {
	ippmUpAndDownReport,		ippmAggrMeasureReport,
	ippmInBandReport,
	ippmOutBandReport,
	ippmAboveReport,
	ippmBelowReport,
	ippmEventsDurationExceededReport,
	ippmCompletedMeasureReport,
	ippmAggrMeasureHistoryFull,
	ippmNetMeasureHistoryFull,		ippmNetMeasureHistoryFull,
	ippmReportLogFull		ippmAggrMeasureHistoryFull
	}		}
	STATUS current		STATUS current
	DESCRIPTION		DESCRIPTION
	"The IPPM Notification Group"		"The IPPM Notification Group"
	::= { ippmGroups 8}		::= { ippmGroups 6}
	END		END
	8 Security Considerations		8 Security Considerations
	8.1 VACM Access control		8.1 VACM Access control
	View Based Access Control, or VACM may be used to restrict access to		View Based Access Control, or VACM may be used to restrict access to
	certain objects, or even object instances within tables. For example,		certain objects, or even object instances within tables. For example,
	one may:		one may:
	+ Give an 'administrator' write access to the ippmOwnersTable,		+ Give an 'administrator' write access to the ippmOwnersTable,
	whereas all other users may only have read access		whereas all other users may only have read access
	+ Give access to individual rows in the network measure, aggregated		+ Give access to individual rows in the network measure, aggregated
	measure, history, and report table to particular owners based upon		measure, history, and report table to particular owners based upon
	indexing on an 'owners name', and even upon a particular measure.		indexing on an 'owners name', and even upon a particular measure.
	This will be illustrated below.		This will be illustrated below.
	+ Give access of one owner’s measure, and associated results, to		+ Give access of one ownerÆs measure, and associated results, to
	another owner in order to create an aggregated measure based upon the		another owner in order to create an aggregated measure based upon the
	results.		results.
	8.1.1 Example of implementing VACM control for the IPPM-REPORTING-MIB		8.1.1 Example of implementing VACM control for the IPPM-REPORTING-MIB
	The following example illustrates how one could use VACM to restrict		The following example illustrates how one could use VACM to restrict
	access to particular objects within the MIB. It uses syntax specific		access to particular objects within the MIB. It uses syntax specific
	to a particular agent development toolkit, but may be generalized		to a particular agent development toolkit, but may be generalized
	using the concepts as defined in the VACM MIB.		using the concepts as defined in the VACM MIB.
	skipping to change at page 74, line 17		skipping to change at page 61, line 9
	It is then a customer/user responsibility to ensure that the SNMP		It is then a customer/user responsibility to ensure that the SNMP
	entity giving access to an instance of this MIB, is properly		entity giving access to an instance of this MIB, is properly
	configured to give access to the objects only to those principals		configured to give access to the objects only to those principals
	(users) that have legitimate rights to indeed GET or SET		(users) that have legitimate rights to indeed GET or SET
	(change/create/delete) them.		(change/create/delete) them.
	9 Document management		9 Document management
	9.1 Open issues		9.1 Open issues
	Usage of accessible-for-notify for an index ?		Smilint complains when accessible-for-notify is used for an index.
	9.2 Changes done since release 03		9.2 Changes done since release 04
			Report Group deleted:
			reportHistoryTable deleted;
			reportSetupTable deleted;
			6 related notifications deleted;
			low and high thresholds added in ippmAggrMeasureTable;
			TC IppmOwnerIndex added to clearly define the owner namespace.
			GMTTimestamp time origine changed to NTP (1900).
			9.3 Changes done since release 03
	+ SMI subtype: INTEGER vs Integer32...;		+ SMI subtype: INTEGER vs Integer32...;
	+ SMI UNITS: Clauses added;		+ SMI UNITS: Clauses added;
	+ cleanup of DEFVAL values;		+ cleanup of DEFVAL values;
	+ Counter/index wrapping:		+ Counter/index wrapping:
	the index of the table wrap independently of the sequence of the		the index of the table wrap independently of the sequence of the
	results. That makes it very difficult for application to track the		results. That makes it very difficult for application to track the
	results. As the sequence id identify the instance of the result of a		results. As the sequence id identify the instance of the result of a
	measure the index is removed both from the table and from the index		measure the index is removed both from the table and from the index
	clause.		clause.
	ippmHistoryIndex removed from ippmHistoryEntry;		ippmHistoryIndex removed from ippmHistoryEntry;
	ippmHistoryIndex removed from the INDEX clause of the table		ippmHistoryIndex removed from the INDEX clause of the table
	ippmHistoryTable;		ippmHistoryTable;
	ippmReportIndex removed from ippmReportEntry;		ippmReportIndex removed from ippmAggrHistoryEntry;
	ippmReportIndex removed from the clause INDEX of ippmReportEntry		ippmReportIndex removed from the clause INDEX of
	INDEX clause of the table ippmReportTable;		ippmAggrHistoryEntry INDEX clause of the table ippmAggrHistoryTable;
	9.3 Changes done since release 02		9.4 Changes done since release 02
	+ Security/VACM:		+ Security/VACM:
	sharing table removed;		sharing table removed;
	ippmMeasure merged with networkMeasure and AggrMeasure to have		ippmMeasure merged with networkMeasure and AggrMeasure to have
	all networkMeasure objects in read only.		all networkMeasure objects in read only.
	Indexes belong to the table;		Indexes belong to the table;
	remove all reference to SNMPv1 ...inSNMPTrapPDU		remove all reference to SNMPv1 ...inSNMPTrapPDU
	+ System:		+ System:
	ippmSystemOperationalStatus added		ippmSystemOperationalStatus added
	ippmSynchronizationTable adapted for proxy mode:		ippmSynchronizationTable adapted for proxy mode:
	ippmPointOfMeasureIndex added to the index of		ippmPointOfMeasureIndex added to the index of
	ippmSystemCurrentSynchronization removed from system		ippmSystemCurrentSynchronization removed from system
	capabilities:		capabilities:
	ippmPointOfMeasureMetrics added to		ippmPointOfMeasureMetrics added to
	IppmPointOfMeasureEntry;		IppmPointOfMeasureEntry;
	ippmMetricType added to ippmMetricsTable;		ippmMetricsType added to ippmMetricsTable;
	+ Owners		+ Owners
	ippmMetricMaxHistorySize replaced with quota in ippmOwnersTable;		ippmMetricMaxHistorySize replaced with quota in ippmOwnersTable;
	+ ippmOnHistoryFullAction replaced with resultsMgmt in aggr and network.;		+ ippmOnHistoryFullAction replaced with resultsMgmt in aggr and network.;
	+ network measure:		+ network measure:
	ippmNetMeasureOperState added to indicate the state of the network		ippmNetMeasureOperState added to indicate the state of the network
	measure		measure
	state;		state;
	added burst mode;		added burst mode;
	state of the measure: nb of singletons collected and oper status		state of the measure: nb of singletons collected and oper status
	added;		added;
	+aggregated metric:		+aggregated metric:
	fast report added to get raw results by email;		fast report added to get raw results by email;
	+ report setup:		+ report setup:
	onReportDeliveryClearHistory removed from IppmReportDefinition;		onReportDeliveryClearHistory removed from
			IppmMetricResultFilter;
	+ Map field added to network, aggr and report tables to help to map		+ Map field added to network, aggr and report tables to help to map
	on topology map or admin view.		on topology map or admin view.
	10 References		10 References
	[1] Bradner, S., "The Internet Standards Process -- Revision 3", BCP		[1] Bradner, S., "The Internet Standards Process -- Revision 3", BCP
	9, RFC 2026, October 1996.		9, RFC 2026, October 1996.
	[2] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for		[2] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for
	Describing SNMP Management Frameworks", RFC 2571, April 1999.		Describing SNMP Management Frameworks", RFC 2571, April 1999.
	[3] Rose, M., and K. McCloghrie, "Structure and Identification of		[3] Rose, M., and K. McCloghrie, "Structure and Identification of
	Management Information for TCP/IP-based Internets", STD 16, RFC		Management Information for TCP/IP-based Internets", STD 16, RFC
	1155, May 1990.		1155, May 1990.
End of changes.
This html diff was produced by rfcdiff 1.23, available from http://www.levkowetz.com/ietf/tools/rfcdiff/