draft-ietf-ips-iscsi-mib-04.txt   draft-ietf-ips-iscsi-mib-05.txt 
Internet Draft Mark Bakke Internet Draft Mark Bakke
<draft-ietf-ips-iscsi-mib-04.txt> Jim Muchow <draft-ietf-ips-iscsi-mib-05.txt> Jim Muchow
Expires August 2002 Cisco Systems Expires December 2002 Cisco Systems
Marjorie Krueger Marjorie Krueger
Hewlett-Packard Hewlett-Packard
Tom McSweeney Tom McSweeney
IBM IBM
February 2002 June 2002
Definitions of Managed Objects for iSCSI Definitions of Managed Objects for iSCSI
1. Status of this Memo 1. Status of this Memo
This document is an Internet-Draft and is in full conformance with This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026. all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that Task Force (IETF), its areas, and its working groups. Note that
skipping to change at page 4, line 16 skipping to change at page 4, line 16
target. iSCSI nodes that serve in an initiator role can target. iSCSI nodes that serve in an initiator role can
also have a list of authorized targets. Each of the also have a list of authorized targets. Each of the
entries in this list points to an identity within the Auth entries in this list points to an identity within the Auth
MIB to which the initiator should attempt to establish MIB to which the initiator should attempt to establish
sessions. The Auth MIB includes information used to sessions. The Auth MIB includes information used to
identify initiators and targets by their iSCSI name, IP identify initiators and targets by their iSCSI name, IP
address, and/or credentials. address, and/or credentials.
6. Discussion 6. Discussion
This MIB structure is intended to satisfy fault, performance, and This MIB structure supplies configuration, fault, and statistics
security management for an iSCSI implementation. It is structured information for iSCSI devices. It is structured around the well-
around the well-known iSCSI objects, such as targets, initiators, known iSCSI objects, such as targets, initiators, sessions,
sessions, connections, and the like. connections, and the like.
This MIB may also be used to configure access to iSCSI targets, by This MIB may also be used to configure access to iSCSI targets, by
creating iSCSI Portals and authorization list entries. creating iSCSI Portals and authorization list entries.
It is worthwhile to note that this is an iSCSI MIB and as such It is worthwhile to note that this is an iSCSI MIB and as such
reflects only iSCSI objects (real or virtual). This means that this reflects only iSCSI objects. This MIB does not contain information
MIB will not directly deal with real SCSI objects or the SCSI about the SCSI-layer attributes of a device. The SCSI MIB, currently
protocol in general. This are represented within the SCSI MIB (work under development, is related to the iSCSI MIB and contains the SCSI
in progress) information about a device.
The iSCSI MIB consists of several "objects", each of which is The iSCSI MIB consists of several "objects", each of which is
represented by one or more tables. This section contains a brief represented by one or more tables. This section contains a brief
description of the "object" hierarchy and a description of each description of the "object" hierarchy and a description of each
object, followed by a discussion of the actual SNMP table structure object, followed by a discussion of the actual MIB table structure
within the objects. within the objects.
6.1. iSCSI MIB Object Model 6.1. iSCSI MIB Object Model
The top-level object in this structure is the iSCSI instance, which The top-level object in this structure is the iSCSI instance, which
"contains" all of the other objects. "contains" all of the other objects.
iscsiInstance iscsiInstance
-- A distinct iSCSI entity within the managed system. -- A distinct iSCSI entity within the managed system.
-- Most implementations will have just one of these.
iscsiPortal iscsiPortal
-- An IP address used by this instance -- An IP address used by this instance
iscsiTargetPortal iscsiTargetPortal
-- Contains portal information relevant when the portal -- Contains portal information relevant when the portal
-- is used to listen for connections to its targets. -- is used to listen for connections to its targets.
iscsiInitiatorPortal iscsiInitiatorPortal
-- Contains portal information relevant when the portal -- Contains portal information relevant when the portal
-- is used to initiate connections to other targets. -- is used to initiate connections to other targets.
iscsiNode iscsiNode
-- An iSCSI node can act as an initiator, a target, or both. -- An iSCSI node can act as an initiator, a target, or both.
-- Contains generic (non-role-specific) information. -- Contains generic (non-role-specific) information.
iscsiTarget iscsiTarget
-- Target-specific iSCSI node information. -- Target-specific iSCSI node information.
iscsiTgtAuth iscsiTgtAuth
-- A list of initiator identities that are allowed -- A list of initiator identities that are allowed
-- access to this target. -- access to this target.
iscsiInitiator iscsiInitiator
-- Initiator-specific iSCSI node information. -- Initiator-specific iSCSI node information.
skipping to change at page 5, line 26 skipping to change at page 5, line 26
-- A list of target identities to which this initiator -- A list of target identities to which this initiator
-- is configured to establish sessions. -- is configured to establish sessions.
iscsiSession iscsiSession
-- An active iSCSI session between an initiator and target. -- An active iSCSI session between an initiator and target.
-- The session's direction may be Inbound (outside -- The session's direction may be Inbound (outside
-- initiator to our target) or Outbound (our initiator to -- initiator to our target) or Outbound (our initiator to
-- an outside target). -- an outside target).
iscsiConnection iscsiConnection
-- An active TCP connection within an iSCSI session -- An active TCP connection within an iSCSI session
An iSCSI Node can take on an initiator role, a target role, or both. An iSCSI Node can be an initiator, a target, or both. The iSCSI
Multiple iSCSI Portals may be present; these can also take on either Node's portals may be used to initiate connections (initiator) or
or both of the roles. The MIB assumes that any target may be listen for connections (target), depending on wither the iSCSI Node
accessed via any portal that can take on a target role, although is acting as an initiator or target. The iSCSI MIB assumes that any
other access controls not reflected in the MIB might limit this. target may be accessed via any portal that can take on a target role,
although other access controls not reflected in the MIB might limit
Logical Units and LUNs are SCSI-level entities, which are covered in this.
[SCSI-MIB].
6.2. iSCSI MIB Table Structure 6.2. iSCSI MIB Table Structure
Each iSCSI "object" is comprised of one or more tables: an attributes Each iSCSI object exports of one or more tables: an attributes table,
table, and zero or more statistics tables which augment the and zero or more statistics tables which augment the attributes
attributes table. Since iSCSI is an evolving standard, it is much table. Since iSCSI is an evolving standard, it is much cleaner to
cleaner to separate statistics and attributes into separate tables, provide statistics and attributes as separate tables, allowing
instead of putting them all into the same table. This allows attributes and statistics to be added independently. In a few cases,
attributes and statistics to be added independently, without mixing there are multiple categories of statistics that will likely grow; in
them and making them appear messy. In a few cases, there are this case, an object will contain multiple statistics tables.
multiple categories of statistics that will likely grow; in this
case, an object will contain multiple statistics tables.
iscsiObjects iscsiObjects
iscsiDescriptors iscsiDescriptors
iscsiInstance iscsiInstance
iscsiInstanceAttributesTable iscsiInstanceAttributesTable
iscsiInstanceSsnErrorStatsTable iscsiInstanceSsnErrorStatsTable
-- Counts abnormal session terminations -- Counts abnormal session terminations
iscsiPortal iscsiPortal
iscsiPortalAttributesTable iscsiPortalAttributesTable
iscsiTargetPortal iscsiTargetPortal
skipping to change at page 7, line 8 skipping to change at page 7, line 5
MIB. Every table entry in this MIB is "owned" by exactly one iSCSI MIB. Every table entry in this MIB is "owned" by exactly one iSCSI
instance; all other table entries in the MIB include this table's instance; all other table entries in the MIB include this table's
index as their primary index. index as their primary index.
Most implementations will include just one iSCSI instance row in this Most implementations will include just one iSCSI instance row in this
table. However, this table exists to allow for multiple virtual table. However, this table exists to allow for multiple virtual
instances. For example, many IP routing products now allow multiple instances. For example, many IP routing products now allow multiple
virtual routers. The iSCSI MIB has the same premise; a large system virtual routers. The iSCSI MIB has the same premise; a large system
could be "partitioned" into multiple, distinct virtual systems. could be "partitioned" into multiple, distinct virtual systems.
This also allows a single SNMP agent to represent multiple This also allows a single SNMP agent to proxy for multiple
subsystems, perhaps a set of stackable devices, each of which have subsystems, perhaps a set of stackable devices, each of which have
one or even more instances. In an iSCSI host, it allows multiple one or even more instances.
vendors' implementations to co-exist under a single SNMP agent; each
could have its own instance.
The instance attributes include the iSCSI vendor and version, as well The instance attributes include the iSCSI vendor and version, as well
as information on the last target or initiator at the other end of a as information on the last target or initiator at the other end of a
session that caused a session failure. session that caused a session failure.
The iscsiInstanceSsnErrorStatsTable augments the attributes table, The iscsiInstanceSsnErrorStatsTable augments the attributes table,
and provides statistics on session failures due to digest, and provides statistics on session failures due to digest,
connection, or iSCSI format errors. connection, or iSCSI format errors.
6.4. iscsiPortal 6.4. iscsiPortal
skipping to change at page 7, line 39 skipping to change at page 7, line 34
a transport protocol (currently only TCP is defined). Each entry a transport protocol (currently only TCP is defined). Each entry
that fulfills an initiator portal role has a corresponding entry in that fulfills an initiator portal role has a corresponding entry in
the iscsiInitiatorPortal table; each entry that has a target portal the iscsiInitiatorPortal table; each entry that has a target portal
role has an entry in the iscsiTargetPortal table. Each portal that role has an entry in the iscsiTargetPortal table. Each portal that
serves both roles has a corresponding entry in each table. serves both roles has a corresponding entry in each table.
Portal entries, along with their initiator and target portal Portal entries, along with their initiator and target portal
counterparts, may be created and destroyed through this MIB by a counterparts, may be created and destroyed through this MIB by a
management station. management station.
WORK - Need to finalize how portal entries and their corresponding When creating a new portal entry, an iscsiPortal is first created,
initiator and target portal entries are created, and document it then the iscsiTargetPortal, iscsiInitiatorPortal, or both.
here. Attributes are added during creation, and may not be subsequently
modified. Creating an iscsiTargetPortal will cause the
WORK When creating a portal entry.... implementation to start listening for iSCSI connections on the
portal. Creating an iscsiInitiatorPortal will not necessarily cause
connections to be established; it is left to the implementation
whether and when to make use of the portal.
WORK When deleting a portal entry....connections are dropped. When deleting a portal entry, all connections associated with that
portal entry are terminated. The implementation may either terminate
the connection immediately, or request a clean shutdown as specified
in [ISCSI]. An outbound connection (when an iscsiInitiatorPortal is
deleted) matches the portal if its iscsiCxnLocalAddr matches the
iscsiPortalAddr. An inbound connection (when an iscsiTargetPortal is
deleted) matches the portal if both its iscsiCxnLocalAddr matches the
iscsiPortalAddr, and the iscsiCxnLocalPort matches the
iscsiTargetPortalPort.
Individual attributes within a portal, initiatorPortal, or Individual attributes within a portal, initiatorPortal, or
targetPortal entry may not be modified. For instance, changing the IP targetPortal entry may not be modified. For instance, changing the IP
address of a portal requires that the portal entries associated with address of a portal requires that the portal entries associated with
the old IP address be deleted, and new entries be created (in either the old IP address be deleted, and new entries be created (in either
order). order).
6.5. iscsiTargetPortal 6.5. iscsiTargetPortal
The iscsiTargetPortalAttributesTable lists local sockets on which the The iscsiTargetPortalAttributesTable contains target-specific
iSCSI instance is listening for incoming connections to its targets. attributes for iSCSI Portals. Entries in this table use the same
Entries in this table use the same indices as their corresponding indices as their corresponding entries in the
entries in the iscsiPortalAttributesTable. iscsiPortalAttributesTable.
This table contains the TCP (or other protocol) port on which the This table contains the TCP (or other protocol) port on which the
socket is listening for incoming connections. It also includes a socket is listening for incoming connections. It also includes a
portal group aggregation tag; iSCSI target portals within this portal group aggregation tag; iSCSI target portals within this
instance sharing the same tag can contain connections within the same instance sharing the same tag can contain connections within the same
session. session.
This table will usually be empty for iSCSI instances that contain This table will be empty for iSCSI instances that contain only
only initiators (such as iSCSI host driver implementations). initiators (such as iSCSI host driver implementations).
6.6. iscsiInitiatorPortal 6.6. iscsiInitiatorPortal
The iscsiInitiatorPortalAttributesTable lists the IP addresses from The iscsiInitiatorPortalAttributesTable contains initiator-specific
which the iSCSI instance may initiate connections to other targets. attributes for iSCSI Portals. Entries in this table use the same
Entries in this table use the same indices as their corresponding indices as their corresponding entries in the
entries in the iscsiPortalAttributesTable. iscsiPortalAttributesTable.
Each entry in this table contains a portal group aggregation tag, Each entry in this table contains a portal group aggregation tag,
indicating which portals an initiator may use together within a indicating which portals an initiator may use together within a
multiple-connection session. multiple-connection session.
This table will usually be empty for iSCSI instances that contain This table will be empty for iSCSI instances that contain only
only targets (such as most iSCSI devices). targets (such as most iSCSI devices).
6.7. iscsiNode 6.7. iscsiNode
The iscsiNodeAttributesTable contains a list of iSCSI nodes, each of The iscsiNodeAttributesTable contains a list of iSCSI nodes, each of
which may have an initiator role, a target role, or both. which may have an initiator role, a target role, or both.
This table contains the node's attributes which are common to both This table contains the node's attributes which are common to both
roles, such as its iSCSI Name and alias string. Attributes specific roles, such as its iSCSI Name and alias string. Attributes specific
to initiators or targets are available in the iscsiTarget and to initiators or targets are available in the iscsiTarget and
iscsiInitiator objects. Each entry in this table that can fulfill a iscsiInitiator objects. Each entry in this table that can fulfill a
target role has a corresponding entry in the iscsiTarget table; each target role has a corresponding entry in the iscsiTarget table; each
entry that fulfills an initiator role has an entry in the entry that fulfills an initiator role has an entry in the
iscsiInitiator table. Nodes such as copy managers that can take on iscsiInitiator table. Nodes such as copy managers that can take on
both roles have a corresponding entry in each table. both roles have a corresponding entry in each table.
WORK - We have some new configuration attributes, some of which This table also contains the login negotiations preferences for this
belong in the node, and others of which go into the target. Need to node. These objects indicate the values this node will offer or
finish these up and document them. prefer in the operational negotiation phase of the login process.
Each entry in the table also contains a RowPointer to the transport Each entry in the table also contains a RowPointer to the transport
table entry in the SCSI MIB which this iSCSI node represents. table entry in the SCSI MIB which this iSCSI node represents.
6.8. iscsiTarget 6.8. iscsiTarget
The iscsiTargetAttributesTable contains a list of iSCSI targets which The iscsiTargetAttributesTable contains target-specific attributes
may be accessed through the iSCSI instance. Each entry in this table for iSCSI nodes. Each entry in this table uses the same index values
uses the same index values as its corresponding iscsiNode entry. as its corresponding iscsiNode entry.
This table contains attributes used to indicate the last failure that This table contains attributes used to indicate the last failure that
was (or should have been) sent as a notification or trap. was (or should have been) sent as a notification or trap.
This table is augmented by the iscsiTargetLoginStatsTable and the This table is augmented by the iscsiTargetLoginStatsTable and the
iscsiTargetLogoutStatsTable, which count the numbers of normal and iscsiTargetLogoutStatsTable, which count the numbers of normal and
abnormal logins and logouts to this target. abnormal logins and logouts to this target.
6.9. iscsiTgtAuthorization 6.9. iscsiTgtAuthorization
The iscsiTgtAuthAttributesTable contains an entry for each initiator The iscsiTgtAuthAttributesTable contains an entry for each initiator
identifier that will be allowed to access the target under which it identifier that will be allowed to access the target under which it
appears. Each entry contains a RowPointer to a user identity in the appears. Each entry contains a RowPointer to a user identity in the
IPS Identity Authentication MIB, which contains the name, address, IPS Identity Authentication MIB, which contains the name, address,
and credential information necessary to authenticate the initiator. and credential information necessary to authenticate the initiator.
6.10. iscsiInitiator 6.10. iscsiInitiator
The iscsiInitiatorAttributesTable contains a list of iSCSI initiators The iscsiInitiatorAttributesTable contains a list of initiator-
which are used by this iSCSI instance to access targets. Each entry specific attributes for iSCSI nodes. Each entry in this table uses
in this table uses the same index values as its corresponding the same index values as its corresponding iscsiNode entry.
iscsiNode entry.
Most implementations will include a single entry in this table, Most implementations will include a single entry in this table,
regardless of the number of physical interfaces the initiator may regardless of the number of physical interfaces the initiator may
use. use.
This table is augmented by the iscsiInitiatorLoginStatsTable and the This table is augmented by the iscsiInitiatorLoginStatsTable and the
iscsiInitiatorLogoutStatsTable, which count the numbers of normal and iscsiInitiatorLogoutStatsTable, which count the numbers of normal and
abnormal logins and logouts to this target. abnormal logins and logouts to this target.
6.11. iscsiIntrAuthorization 6.11. iscsiIntrAuthorization
skipping to change at page 10, line 33 skipping to change at page 10, line 39
appears. Outbound sessions are from the initiator node under which appears. Outbound sessions are from the initiator node under which
the session appears to a target outside this iSCSI instance. the session appears to a target outside this iSCSI instance.
Many attributes may be negotiated when starting an iSCSI session. Many attributes may be negotiated when starting an iSCSI session.
Most of these attributes are included in the session object. Most of these attributes are included in the session object.
Some attributes, such as the integrity and authentication schemes, Some attributes, such as the integrity and authentication schemes,
have some standard values which can be extended by vendors to include have some standard values which can be extended by vendors to include
their own schemes. These contain an object identifier, rather than their own schemes. These contain an object identifier, rather than
the expected enumerated type, to allow these values to be extended by the expected enumerated type, to allow these values to be extended by
other MIBs, such as a enterprise MIBs. other MIBs, such as an enterprise MIB.
The iscsiSessionStatsTable includes statistics related to The iscsiSessionStatsTable includes statistics related to
performance; counting iSCSI data bytes and PDUs. performance; it counts iSCSI data bytes and PDUs.
For implementations that support error recovery without terminating a For implementations that support error recovery without terminating a
session, the iscsiSessionCxnErrorStatsTable contains counters for the session, the iscsiSessionCxnErrorStatsTable contains counters for the
numbers of digest and connection errors that have occurred within the numbers of digest and connection errors that have occurred within the
session. session.
6.13. iscsiConnection 6.13. iscsiConnection
The iscsiConnectionAttributesTable contains a list of active The iscsiConnectionAttributesTable contains a list of active
connections within each session. It contains the IP addresses and connections within each session. It contains the IP addresses and
skipping to change at page 11, line 14 skipping to change at page 11, line 20
iSCSI specification; they are meant to be simplified, higher-level iSCSI specification; they are meant to be simplified, higher-level
definitions of connection state that provide information more useful definitions of connection state that provide information more useful
to a user or network manager. to a user or network manager.
No statistics are kept for connections. No statistics are kept for connections.
6.14. IP Addresses and TCP Port Numbers 6.14. IP Addresses and TCP Port Numbers
The IP addresses in this MIB are represented by two attributes, one The IP addresses in this MIB are represented by two attributes, one
of type InetAddressType, and the other of type InetAddress. These of type InetAddressType, and the other of type InetAddress. These
are taken from [IPV6MIB], which is an update to [RFC2851] specifying are taken from [RFC3291], which specifies how to support addresses
how to support addresses that may be either IPv4 or IPv6. that may be either IPv4 or IPv6.
The TCP port numbers that appear in a few of the structures are The TCP port numbers that appear in a few of the structures are
described as simply port numbers, with a protocol attribute described as simply port numbers, with a protocol attribute
indicating whether they are TCP ports, or something else. This will indicating whether they are TCP ports, or something else. This will
allow the MIB to be compatible with iSCSI over transports other than allow the MIB to be compatible with iSCSI over transports other than
TCP in the future. TCP in the future.
6.15. Descriptors: Using OIDs in Place of Enumerated Types 6.15. Descriptors: Using OIDs in Place of Enumerated Types
The iSCSI MIB has a few attributes, such as the authentication and The iSCSI MIB has a few attributes, such as the authentication and
skipping to change at page 13, line 8 skipping to change at page 13, line 8
The 3-in-10 rule was chosen because one notification every three The 3-in-10 rule was chosen because one notification every three
seconds was deemed often enough, but should two or three different seconds was deemed often enough, but should two or three different
notifications happen at the same time, it would not be desirable to notifications happen at the same time, it would not be desirable to
suppress them. Three notifications in ten seconds is a happy medium, suppress them. Three notifications in ten seconds is a happy medium,
where a short burst of notifications is allowed, without inundating where a short burst of notifications is allowed, without inundating
the network and/or trap host with a large number of notifications. the network and/or trap host with a large number of notifications.
7. MIB Definitions 7. MIB Definitions
ISCSI-MIB DEFINITIONS ::= BEGIN ISCSI-MIB DEFINITIONS ::= BEGIN
IMPORTS IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, OBJECT-IDENTITY, NOTIFICATION-TYPE, MODULE-IDENTITY, OBJECT-TYPE, OBJECT-IDENTITY, NOTIFICATION-TYPE,
Unsigned32, Counter32, Counter64, Gauge32, BITS, Unsigned32, Counter32, Counter64, Gauge32,
experimental experimental
FROM SNMPv2-SMI FROM SNMPv2-SMI
TEXTUAL-CONVENTION, TruthValue, RowPointer, TimeStamp, RowStatus, TEXTUAL-CONVENTION, TruthValue, RowPointer, TimeStamp, RowStatus,
AutonomousType AutonomousType
FROM SNMPv2-TC FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF FROM SNMPv2-CONF
SnmpAdminString SnmpAdminString
FROM SNMP-FRAMEWORK-MIB -- RFC 2571 FROM SNMP-FRAMEWORK-MIB -- RFC 2571
InetAddressType, InetAddress InetAddressType, InetAddress
FROM INET-ADDRESS-MIB FROM INET-ADDRESS-MIB -- RFC 3291
; ;
iscsiModule MODULE-IDENTITY iscsiModule MODULE-IDENTITY
LAST-UPDATED "200202040000Z" LAST-UPDATED "200206260000Z" -- June 26, 2002
ORGANIZATION "IETF IPS Working Group" ORGANIZATION "IETF IPS Working Group"
CONTACT-INFO CONTACT-INFO
" "
Mark Bakke Mark Bakke
Postal: Cisco Systems, Inc Postal: Cisco Systems, Inc
6450 Wedgwood Road, Suite 130 6450 Wedgwood Road, Suite 130
Maple Grove, MN Maple Grove, MN
USA 55311 USA 55311
Tel: +1 763-398-1000 Tel: +1 763-398-1000
skipping to change at page 14, line 8 skipping to change at page 14, line 4
Fax: +1 763-398-1001 Fax: +1 763-398-1001
E-mail: mbakke@cisco.com E-mail: mbakke@cisco.com
Marjorie Krueger Marjorie Krueger
Postal: Hewlett-Packard Postal: Hewlett-Packard
Networked Storage Architecture Networked Storage Architecture
Networked Storage Solutions Org. Networked Storage Solutions Org.
8000 Foothills Blvd. 8000 Foothills Blvd.
Roseville, CA 95747 Roseville, CA 95747
Tel: +1 916-785-2656 Tel: +1 916-785-2656
Tel: +1 916-785-0391 Tel: +1 916-785-0391
Email: marjorie_krueger@hp.com Email: marjorie_krueger@hp.com
Tom McSweeney
Postal: IBM Corporation
600 Park Offices Drive
Research Triangle Park, NC
USA 27709
Tel: +1-919-254-5634
Fax: +1-919-254-0391
E-mail: rf42tpme@us.ibm.com
Jim Muchow Jim Muchow
Postal: Cisco Systems, Inc Postal: Cisco Systems, Inc
6450 Wedgwood Road, Suite 130 6450 Wedgwood Road, Suite 130
Maple Grove, MN Maple Grove, MN
USA 55311 USA 55311
Tel: +1 763-398-1000 Tel: +1 763-398-1000
Fax: +1 763-398-1001 Fax: +1 763-398-1001
E-mail: jmuchow@cisco.com" E-mail: jmuchow@cisco.com"
DESCRIPTION DESCRIPTION
"The iSCSI Protocol MIB module." "The iSCSI Protocol MIB module."
REVISION "200202040000Z" -- February 4, 2002 REVISION "200206260000Z" -- June 26, 2002
DESCRIPTION DESCRIPTION
"Initial revision published as RFC xxxx." "Initial revision published as RFC xxxx."
::= { experimental 9999 } -- in case you want to COMPILE -- ::= { mib-2 xx } to be assigned by IANA.
-- in case you want to COMPILE
::= { experimental 9999 }
iscsiObjects OBJECT IDENTIFIER ::= { iscsiModule 1 } iscsiObjects OBJECT IDENTIFIER ::= { iscsiModule 1 }
iscsiNotifications OBJECT IDENTIFIER ::= { iscsiModule 2 } iscsiNotifications OBJECT IDENTIFIER ::= { iscsiModule 2 }
iscsiConformance OBJECT IDENTIFIER ::= { iscsiModule 3 } iscsiConformance OBJECT IDENTIFIER ::= { iscsiModule 3 }
-- Textual Conventions -- Textual Conventions
IscsiTransportProtocols ::= TEXTUAL-CONVENTION IscsiTransportProtocols ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d" DISPLAY-HINT "d"
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This data type is used to define the transport "This data type is used to define the transport
protocols that will carry iSCSI PDUs." protocols that will carry iSCSI PDUs."
REFERENCE REFERENCE
"RFC791, RFC1700 "RFC791, RFC1700
The presently known, officially delegated numbers The presently known, officially delegated numbers
can be found at: can be found at:
http://www.iana.org/assignments/protocol-numbers"
http://www.iana.org/assignments/protocol-numbers
"
SYNTAX INTEGER (0..255) SYNTAX INTEGER (0..255)
IscsiDigestMethod ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This data type represents the methods possible
for digest negotiation.
none - a placeholder for a secondary digest method
that means only the primary method can be
used.
other - a digest method other than those defined below;
noDigest - does not support digests (will operate without
a digest (NOTE: implementations MUST support
digests to be compliant with the iSCSI RFC);
CRC32c - require a CRC32C digest."
SYNTAX INTEGER {
none(1),
other(2),
noDigest(3),
crc32c(4)
}
------------------------------------------------------------------------ ------------------------------------------------------------------------
iscsiDescriptors OBJECT IDENTIFIER ::= { iscsiObjects 1 } iscsiDescriptors OBJECT IDENTIFIER ::= { iscsiObjects 1 }
iscsiHeaderIntegrityTypes OBJECT IDENTIFIER ::= { iscsiDescriptors 1 } iscsiHeaderIntegrityTypes OBJECT IDENTIFIER ::= { iscsiDescriptors 1 }
iscsiHdrIntegrityNone OBJECT-IDENTITY iscsiHdrIntegrityNone OBJECT-IDENTITY
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The authoritative identifier when no integrity "The authoritative identifier when no integrity
skipping to change at page 21, line 11 skipping to change at page 21, line 38
to a particular portal instance." to a particular portal instance."
INDEX { iscsiInstIndex, iscsiPortalIndex } INDEX { iscsiInstIndex, iscsiPortalIndex }
::= { iscsiPortalAttributesTable 1 } ::= { iscsiPortalAttributesTable 1 }
IscsiPortalAttributesEntry ::= SEQUENCE { IscsiPortalAttributesEntry ::= SEQUENCE {
iscsiPortalIndex Unsigned32, iscsiPortalIndex Unsigned32,
iscsiPortalRowStatus RowStatus, iscsiPortalRowStatus RowStatus,
iscsiPortalRoles BITS, iscsiPortalRoles BITS,
iscsiPortalAddrType InetAddressType, iscsiPortalAddrType InetAddressType,
iscsiPortalAddr InetAddress, iscsiPortalAddr InetAddress,
iscsiPortalProtocol IscsiTransportProtocols iscsiPortalProtocol IscsiTransportProtocols,
iscsiPortalMaxRecvDataSegLength INTEGER,
iscsiPortalPrimaryHdrDigest IscsiDigestMethod,
iscsiPortalPrimaryDataDigest IscsiDigestMethod,
iscsiPortalSecondaryHdrDigest IscsiDigestMethod,
iscsiPortalSecondaryDataDigest IscsiDigestMethod,
iscsiPortalRecvMarker TruthValue
} }
iscsiPortalIndex OBJECT-TYPE iscsiPortalIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295) SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An arbitrary integer used to uniquely identify a particular "An arbitrary integer used to uniquely identify a particular
transport endpoint within this iSCSI instance." transport endpoint within this iSCSI instance."
::= { iscsiPortalAttributesEntry 1 } ::= { iscsiPortalAttributesEntry 1 }
skipping to change at page 22, line 24 skipping to change at page 23, line 9
iscsiPortalProtocol OBJECT-TYPE iscsiPortalProtocol OBJECT-TYPE
SYNTAX IscsiTransportProtocols SYNTAX IscsiTransportProtocols
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The portal's transport protocol." "The portal's transport protocol."
DEFVAL { 6 } -- TCP DEFVAL { 6 } -- TCP
::= { iscsiPortalAttributesEntry 6 } ::= { iscsiPortalAttributesEntry 6 }
iscsiPortalMaxRecvDataSegLength OBJECT-TYPE
SYNTAX INTEGER (512..16777215)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum PDU length this portal can receive.
This may be constrained by hardware characteristics
and individual implementations may chose not to
allow this object to be changed."
DEFVAL { 8192 }
::= { iscsiPortalAttributesEntry 7 }
iscsiPortalPrimaryHdrDigest OBJECT-TYPE
SYNTAX IscsiDigestMethod
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The preferred header digest for this portal."
DEFVAL { noDigest }
::= { iscsiPortalAttributesEntry 8 }
iscsiPortalPrimaryDataDigest OBJECT-TYPE
SYNTAX IscsiDigestMethod
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The preferred data digest method for this portal."
DEFVAL { noDigest }
::= { iscsiPortalAttributesEntry 9 }
iscsiPortalSecondaryHdrDigest OBJECT-TYPE
SYNTAX IscsiDigestMethod
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An alternate header digest preference for this portal."
DEFVAL { none }
::= { iscsiPortalAttributesEntry 10 }
iscsiPortalSecondaryDataDigest OBJECT-TYPE
SYNTAX IscsiDigestMethod
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An alternate data digest preference for this portal."
DEFVAL { none }
::= { iscsiPortalAttributesEntry 11 }
iscsiPortalRecvMarker OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates whether or not this portal will
request markers in it's incoming data stream."
::= { iscsiPortalAttributesEntry 12 }
---------------------------------------------------------------------- ----------------------------------------------------------------------
iscsiTargetPortal OBJECT IDENTIFIER ::= { iscsiObjects 4 } iscsiTargetPortal OBJECT IDENTIFIER ::= { iscsiObjects 4 }
-- Target Portal Attributes Table -- Target Portal Attributes Table
iscsiTgtPortalAttributesTable OBJECT-TYPE iscsiTgtPortalAttributesTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiTgtPortalAttributesEntry SYNTAX SEQUENCE OF IscsiTgtPortalAttributesEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
skipping to change at page 25, line 10 skipping to change at page 26, line 51
"An entry (row) containing managment information applicable "An entry (row) containing managment information applicable
to a particular iSCSI node." to a particular iSCSI node."
INDEX { iscsiInstIndex, iscsiNodeIndex } INDEX { iscsiInstIndex, iscsiNodeIndex }
::= { iscsiNodeAttributesTable 1 } ::= { iscsiNodeAttributesTable 1 }
IscsiNodeAttributesEntry ::= SEQUENCE { IscsiNodeAttributesEntry ::= SEQUENCE {
iscsiNodeIndex Unsigned32, iscsiNodeIndex Unsigned32,
iscsiNodeName SnmpAdminString, iscsiNodeName SnmpAdminString,
iscsiNodeAlias SnmpAdminString, iscsiNodeAlias SnmpAdminString,
iscsiNodeRoles BITS, iscsiNodeRoles BITS,
iscsiNodeTransportType RowPointer iscsiNodeTransportType RowPointer,
iscsiNodeInitialR2T TruthValue,
iscsiNodeBidiInitialR2T TruthValue,
iscsiNodeImmediateData TruthValue,
iscsiNodeMaxOutstandingR2T INTEGER,
iscsiNodeFirstBurstSize INTEGER,
iscsiNodeMaxBurstSize INTEGER,
iscsiNodeMaxConnections INTEGER,
iscsiNodeDataSequenceInOrder TruthValue,
iscsiNodeDataPduInOrder TruthValue,
iscsiNodeDefaultTime2Wait INTEGER,
iscsiNodeDefaultTime2Retain INTEGER,
iscsiNodeErrorRecoveryLevel INTEGER
} }
iscsiNodeIndex OBJECT-TYPE iscsiNodeIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295) SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An arbitrary integer used to uniquely identify a particular "An arbitrary integer used to uniquely identify a particular
node within an iSCSI instance present on the local system." node within an iSCSI instance present on the local system."
::= { iscsiNodeAttributesEntry 1 } ::= { iscsiNodeAttributesEntry 1 }
skipping to change at page 26, line 27 skipping to change at page 28, line 32
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A pointer to the corresponding scsiTrnspt object in "A pointer to the corresponding scsiTrnspt object in
the SCSI MIB (which in turn points to this iSCSI node) the SCSI MIB (which in turn points to this iSCSI node)
allowing management stations to locate the SCSI-level allowing management stations to locate the SCSI-level
Device that is represented by this iscsiNode." Device that is represented by this iscsiNode."
REFERENCE REFERENCE
"SCSI-MIB" "SCSI-MIB"
::= { iscsiNodeAttributesEntry 5 } ::= { iscsiNodeAttributesEntry 5 }
iscsiNodeInitialR2T OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates InitialR2T preference for this node -
True = YES,
False = will try to negotiate NO, will accept YES "
DEFVAL { true }
::= { iscsiNodeAttributesEntry 6 }
iscsiNodeBidiInitialR2T OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates BidiInitialR2T preference for this node-
True = YES,
False = will try to negotiate NO, will accept YES "
DEFVAL { true }
::= { iscsiNodeAttributesEntry 7 }
iscsiNodeImmediateData OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object indicates ImmediateData preference for this node
True = YES (but will accept NO),
False = NO "
DEFVAL { true }
::= { iscsiNodeAttributesEntry 8 }
iscsiNodeMaxOutstandingR2T OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Maximum number of outstanding R2Ts allowed per task."
DEFVAL { 1 }
::= { iscsiNodeAttributesEntry 9 }
iscsiNodeFirstBurstSize OBJECT-TYPE
SYNTAX INTEGER (512..16777215)
UNITS "bytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum length (bytes) supported for unsolicited data
to/from this node."
DEFVAL { 65536 }
::= { iscsiNodeAttributesEntry 10 }
iscsiNodeMaxBurstSize OBJECT-TYPE
SYNTAX INTEGER (512..16777215)
UNITS "bytes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum number of bytes which can be sent within
a single sequence of Data-In or Data-Out PDUs."
DEFVAL { 262144 }
::= { iscsiNodeAttributesEntry 11 }
iscsiNodeMaxConnections OBJECT-TYPE
SYNTAX INTEGER (1..65535)
UNITS "connections"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum number of connections allowed in each
session to and/or from this node."
DEFVAL { 1 }
::= { iscsiNodeAttributesEntry 12 }
iscsiNodeDataSequenceInOrder OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The DataSequenceInOrder preference of this node.
False (=No) indicates that iSCSI data PDU sequences may
be transferred in any order. True (=Yes) indicates that
data PDU sequences must be tranferred using
continuously increasing offsets, except during
error recovery."
DEFVAL { true }
::= { iscsiNodeAttributesEntry 13 }
iscsiNodeDataPduInOrder OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The DataPDUInOrder preference of this node.
False (=No) indicates that iSCSI data PDUs within sequences
may be in any order. True (=Yes) indicates that data PDUs
within sequences must be at continuously increasing
addresses, with no gaps or overlay between PDUs."
DEFVAL { true }
::= { iscsiNodeAttributesEntry 14 }
iscsiNodeDefaultTime2Wait OBJECT-TYPE
SYNTAX INTEGER (0..3600)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The DefaultTime2Wait preference of this node.
This is the minimum time, in seconds, to wait before attempting
an explicit/implicit logout or active task reassignment after
an unexpected connection termination or a connection reset."
DEFVAL { 2 }
::= { iscsiNodeAttributesEntry 15 }
iscsiNodeDefaultTime2Retain OBJECT-TYPE
SYNTAX INTEGER (0..3600)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The DefaultTime2Retain preference of this node.
This is the maximum time, in seconds after an initial wait
(Time2Wait), before which an active task reassignment is still
possible after an unexpected connection termination or a
connection reset."
DEFVAL { 20 }
::= { iscsiNodeAttributesEntry 16 }
iscsiNodeErrorRecoveryLevel OBJECT-TYPE
SYNTAX INTEGER (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The ErrorRecoveryLevel preference of this node.
Currently, only 0-2 are valid.
This object is designed to accommodate future error recover
levels.
Higher error recovery levels imply support in addition to
support for the lower error level functions. In otherwords,
error level 2 implies support for levels 0-1, since those
functions are subsets of error level 2."
DEFVAL { 0 }
::= { iscsiNodeAttributesEntry 17 }
---------------------------------------------------------------------- ----------------------------------------------------------------------
iscsiTarget OBJECT IDENTIFIER ::= { iscsiObjects 7 } iscsiTarget OBJECT IDENTIFIER ::= { iscsiObjects 7 }
-- Target Attributes Table -- Target Attributes Table
iscsiTargetAttributesTable OBJECT-TYPE iscsiTargetAttributesTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiTargetAttributesEntry SYNTAX SEQUENCE OF IscsiTargetAttributesEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
skipping to change at page 32, line 14 skipping to change at page 37, line 19
DESCRIPTION DESCRIPTION
"An entry (row) containing management information "An entry (row) containing management information
applicable to a particular target node's authorized applicable to a particular target node's authorized
initiator identity." initiator identity."
INDEX { iscsiInstIndex, iscsiNodeIndex, iscsiTgtAuthIndex } INDEX { iscsiInstIndex, iscsiNodeIndex, iscsiTgtAuthIndex }
::= { iscsiTgtAuthAttributesTable 1 } ::= { iscsiTgtAuthAttributesTable 1 }
IscsiTgtAuthAttributesEntry ::= SEQUENCE { IscsiTgtAuthAttributesEntry ::= SEQUENCE {
iscsiTgtAuthIndex Unsigned32, iscsiTgtAuthIndex Unsigned32,
iscsiTgtAuthRowStatus RowStatus, iscsiTgtAuthRowStatus RowStatus,
iscsiTgtAuthUser RowPointer iscsiTgtAuthIdentity RowPointer
} }
iscsiTgtAuthIndex OBJECT-TYPE iscsiTgtAuthIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295) SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An arbitrary integer used to uniquely identify a particular "An arbitrary integer used to uniquely identify a particular
target's authorized initiator identity within an iSCSI target's authorized initiator identity within an iSCSI
instance present on the local system." instance present on the local system."
::= { iscsiTgtAuthAttributesEntry 1 } ::= { iscsiTgtAuthAttributesEntry 1 }
iscsiTgtAuthRowStatus OBJECT-TYPE iscsiTgtAuthRowStatus OBJECT-TYPE
SYNTAX RowStatus SYNTAX RowStatus
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The status of the row." "The status of the row."
::= { iscsiTgtAuthAttributesEntry 2 } ::= { iscsiTgtAuthAttributesEntry 2 }
iscsiTgtAuthUser OBJECT-TYPE iscsiTgtAuthIdentity OBJECT-TYPE
SYNTAX RowPointer SYNTAX RowPointer
MAX-ACCESS read-create MAX-ACCESS read-create
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A pointer to the corresponding IPS-AUTH MIB user entry "A pointer to the corresponding IPS-AUTH MIB user entry
that will be allowed to access this iSCSI target." that will be allowed to access this iSCSI target."
REFERENCE
"IPS-AUTH MIB"
::= { iscsiTgtAuthAttributesEntry 3 } ::= { iscsiTgtAuthAttributesEntry 3 }
---------------------------------------------------------------------- ----------------------------------------------------------------------
iscsiInitiator OBJECT IDENTIFIER ::= { iscsiObjects 9 } iscsiInitiator OBJECT IDENTIFIER ::= { iscsiObjects 9 }
-- Initiator Attributes Table -- Initiator Attributes Table
iscsiInitiatorAttributesTable OBJECT-TYPE iscsiInitiatorAttributesTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiInitiatorAttributesEntry SYNTAX SEQUENCE OF IscsiInitiatorAttributesEntry
skipping to change at page 38, line 33 skipping to change at page 43, line 38
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An entry (row) containing managment information applicable "An entry (row) containing managment information applicable
to a particular initiator node's authorized target identity." to a particular initiator node's authorized target identity."
INDEX { iscsiInstIndex, iscsiNodeIndex, iscsiIntrAuthIndex } INDEX { iscsiInstIndex, iscsiNodeIndex, iscsiIntrAuthIndex }
::= { iscsiIntrAuthAttributesTable 1 } ::= { iscsiIntrAuthAttributesTable 1 }
IscsiIntrAuthAttributesEntry ::= SEQUENCE { IscsiIntrAuthAttributesEntry ::= SEQUENCE {
iscsiIntrAuthIndex Unsigned32, iscsiIntrAuthIndex Unsigned32,
iscsiIntrAuthRowStatus RowStatus, iscsiIntrAuthRowStatus RowStatus,
iscsiIntrAuthUser RowPointer iscsiIntrAuthIdentity RowPointer
} }
iscsiIntrAuthIndex OBJECT-TYPE iscsiIntrAuthIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295) SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An arbitrary integer used to uniquely identify a "An arbitrary integer used to uniquely identify a
particular initiator node's authorized target particular initiator node's authorized target
identity within an iSCSI instance present on the identity within an iSCSI instance present on the
skipping to change at page 39, line 4 skipping to change at page 44, line 11
identity within an iSCSI instance present on the identity within an iSCSI instance present on the
local system." local system."
::= { iscsiIntrAuthAttributesEntry 1 } ::= { iscsiIntrAuthAttributesEntry 1 }
iscsiIntrAuthRowStatus OBJECT-TYPE iscsiIntrAuthRowStatus OBJECT-TYPE
SYNTAX RowStatus SYNTAX RowStatus
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The status of the row." "The status of the row."
::= { iscsiIntrAuthAttributesEntry 2 } ::= { iscsiIntrAuthAttributesEntry 2 }
iscsiIntrAuthUser OBJECT-TYPE iscsiIntrAuthIdentity OBJECT-TYPE
SYNTAX RowPointer SYNTAX RowPointer
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A pointer to the corresponding IPS-AUTH MIB user entry "A pointer to the corresponding IPS-AUTH MIB user entry
to which this initiator node should attempt to establish to which this initiator node should attempt to establish
an iSCSI session." an iSCSI session."
REFERENCE REFERENCE
"IPS-AUTH MIB" "IPS-AUTH MIB"
::= { iscsiIntrAuthAttributesEntry 3 } ::= { iscsiIntrAuthAttributesEntry 3 }
skipping to change at page 39, line 49 skipping to change at page 45, line 6
"An entry (row) containing management information applicable "An entry (row) containing management information applicable
to a particular session." to a particular session."
INDEX { iscsiInstIndex, iscsiNodeIndex, iscsiSsnIndex } INDEX { iscsiInstIndex, iscsiNodeIndex, iscsiSsnIndex }
::= { iscsiSessionAttributesTable 1 } ::= { iscsiSessionAttributesTable 1 }
IscsiSessionAttributesEntry ::= SEQUENCE { IscsiSessionAttributesEntry ::= SEQUENCE {
iscsiSsnIndex Unsigned32, iscsiSsnIndex Unsigned32,
iscsiSsnDirection INTEGER, iscsiSsnDirection INTEGER,
iscsiSsnInitiatorName SnmpAdminString, iscsiSsnInitiatorName SnmpAdminString,
iscsiSsnTargetName SnmpAdminString, iscsiSsnTargetName SnmpAdminString,
iscsiSsnTsid INTEGER, iscsiSsnTsih INTEGER,
iscsiSsnIsid OCTET STRING, iscsiSsnIsid OCTET STRING,
iscsiSsnInitiatorAlias SnmpAdminString, iscsiSsnInitiatorAlias SnmpAdminString,
iscsiSsnTargetAlias SnmpAdminString, iscsiSsnTargetAlias SnmpAdminString,
iscsiSsnInitialR2t TruthValue, iscsiSsnInitialR2T TruthValue,
iscsiSsnBidiInitialR2t TruthValue, iscsiSsnBidiInitialR2T TruthValue,
iscsiSsnImmediateData TruthValue, iscsiSsnImmediateData TruthValue,
iscsiSsnType INTEGER, iscsiSsnType INTEGER,
iscsiSsnMaxOutstandingR2t INTEGER, iscsiSsnMaxOutstandingR2T INTEGER,
iscsiSsnFirstBurstSize INTEGER, iscsiSsnFirstBurstSize INTEGER,
iscsiSsnMaxBurstSize INTEGER, iscsiSsnMaxBurstSize INTEGER,
iscsiSsnConnectionNumber Gauge32, iscsiSsnConnectionNumber Gauge32,
iscsiSsnMaxConnections Gauge32, iscsiSsnAuthIdentity RowPointer,
iscsiSsnAuthMethod AutonomousType,
iscsiSsnDataSequenceInOrder TruthValue, iscsiSsnDataSequenceInOrder TruthValue,
iscsiSsnDataPduInOrder TruthValue, iscsiSsnDataPduInOrder TruthValue,
iscsiSsnLogoutLoginMaxTime INTEGER,
iscsiSsnErrorRecoveryLevel INTEGER iscsiSsnErrorRecoveryLevel INTEGER
} }
iscsiSsnIndex OBJECT-TYPE iscsiSsnIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295) SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An arbitrary integer used to uniquely identify a "An arbitrary integer used to uniquely identify a
particular session within an iSCSI instance present particular session within an iSCSI instance present
skipping to change at page 41, line 25 skipping to change at page 46, line 29
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"If iscsiSsnDirection is Outbound, this object is an "If iscsiSsnDirection is Outbound, this object is an
octet string that will contain the name of the remote octet string that will contain the name of the remote
target. target.
If iscsiSsnDirection is Inbound, this object will If iscsiSsnDirection is Inbound, this object will
contain a zero-length string." contain a zero-length string."
::= { iscsiSessionAttributesEntry 4 } ::= { iscsiSessionAttributesEntry 4 }
iscsiSsnTsid OBJECT-TYPE iscsiSsnTsih OBJECT-TYPE
SYNTAX INTEGER (1..65535) SYNTAX INTEGER (1..65535)
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The target-defined portion of the iSCSI Session ID." "The target-defined identification handle for this session."
::= { iscsiSessionAttributesEntry 5 } ::= { iscsiSessionAttributesEntry 5 }
iscsiSsnIsid OBJECT-TYPE iscsiSsnIsid OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(6)) SYNTAX OCTET STRING (SIZE(6))
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The initiator-defined portion of the iSCSI Session ID." "The initiator-defined portion of the iSCSI Session ID."
::= { iscsiSessionAttributesEntry 6 } ::= { iscsiSessionAttributesEntry 6 }
skipping to change at page 42, line 16 skipping to change at page 47, line 19
SYNTAX SnmpAdminString SYNTAX SnmpAdminString
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An octet string that gives the alias communicated by the "An octet string that gives the alias communicated by the
target end of the session during the login phase. target end of the session during the login phase.
If no alias exists, the value is a zero-length string." If no alias exists, the value is a zero-length string."
::= { iscsiSessionAttributesEntry 8 } ::= { iscsiSessionAttributesEntry 8 }
iscsiSsnInitialR2t OBJECT-TYPE iscsiSsnInitialR2T OBJECT-TYPE
SYNTAX TruthValue SYNTAX TruthValue
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"If set to true, indicates that the initiator must wait "If set to true, indicates that the initiator must wait
for an R2T before sending to the target. If set to false, for an R2T before sending to the target. If set to false,
the initiator may send data immediately, within limits set the initiator may send data immediately, within limits set
by iscsiSsnFirstBurstSize and the expected data transfer by iscsiSsnFirstBurstSize and the expected data transfer
length of the request. length of the request.
Default is true." Default is true."
::= { iscsiSessionAttributesEntry 9 } ::= { iscsiSessionAttributesEntry 9 }
iscsiSsnBidiInitialR2t OBJECT-TYPE iscsiSsnBidiInitialR2T OBJECT-TYPE
SYNTAX TruthValue SYNTAX TruthValue
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"If set to true, indicates that the initiator must wait "If set to true, indicates that the initiator must wait
for an R2T before sending data to the target within a for an R2T before sending data to the target within a
bi-directional (both read and write) request. If false, bi-directional (both read and write) request. If false,
the initiator may send unsolicited write data as part the initiator may send unsolicited write data as part
of the request." of the request."
::= { iscsiSessionAttributesEntry 10 } ::= { iscsiSessionAttributesEntry 10 }
iscsiSsnImmediateData OBJECT-TYPE iscsiSsnImmediateData OBJECT-TYPE
SYNTAX TruthValue SYNTAX TruthValue
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Indicates whether the initiator and target have agreed to support "Indicates whether the initiator and target have agreed to support
immediate commands on this session." immediate data on this session."
::= { iscsiSessionAttributesEntry 11 } ::= { iscsiSessionAttributesEntry 11 }
iscsiSsnType OBJECT-TYPE iscsiSsnType OBJECT-TYPE
SYNTAX INTEGER { SYNTAX INTEGER {
normalSession(1), normalSession(1),
discoverySession(2) discoverySession(2)
} }
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"Type of iSCSI session: "Type of iSCSI session:
normalSession - session is a normal iSCSI session normalSession - session is a normal iSCSI session
discoverySession - session is being used only for discovery." discoverySession - session is being used only for discovery."
DEFVAL { normalSession }
::= { iscsiSessionAttributesEntry 12 } ::= { iscsiSessionAttributesEntry 12 }
iscsiSsnMaxOutstandingR2t OBJECT-TYPE iscsiSsnMaxOutstandingR2T OBJECT-TYPE
SYNTAX INTEGER (1..65535) SYNTAX INTEGER (1..65535)
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The maximum number of outstanding request-to-transmit "The maximum number of outstanding request-to-transmit
(R2T)s per task within this session." (R2T)s per task within this session."
::= { iscsiSessionAttributesEntry 13 } ::= { iscsiSessionAttributesEntry 13 }
iscsiSsnFirstBurstSize OBJECT-TYPE iscsiSsnFirstBurstSize OBJECT-TYPE
SYNTAX INTEGER (0..8388480) SYNTAX INTEGER (512..16777215)
UNITS "bytes" UNITS "bytes"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The maximum length supported for unsolicited data sent "The maximum length supported for unsolicited data sent
within this session. within this session."
DEFVAL { 65536 }
Note that the size of reported in bytes even though
the negotiation is in 512k blocks."
::= { iscsiSessionAttributesEntry 14 } ::= { iscsiSessionAttributesEntry 14 }
iscsiSsnMaxBurstSize OBJECT-TYPE iscsiSsnMaxBurstSize OBJECT-TYPE
SYNTAX INTEGER (0..33553920) SYNTAX INTEGER (512..16777215)
UNITS "bytes" UNITS "bytes"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The maximum number of bytes which can be sent within "The maximum number of bytes which can be sent within
a single sequence of Data-In or Data-Out PDUs." a single sequence of Data-In or Data-Out PDUs."
DEFVAL { 262144 }
::= { iscsiSessionAttributesEntry 15 } ::= { iscsiSessionAttributesEntry 15 }
iscsiSsnConnectionNumber OBJECT-TYPE iscsiSsnConnectionNumber OBJECT-TYPE
SYNTAX Gauge32 (1..65535) SYNTAX Gauge32 (1..65535)
UNITS "connections" UNITS "connections"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The number of transport protocol connections that currently "The number of transport protocol connections that currently
belong to this session." belong to this session."
::= { iscsiSessionAttributesEntry 16 } ::= { iscsiSessionAttributesEntry 16 }
iscsiSsnMaxConnections OBJECT-TYPE iscsiSsnAuthIdentity OBJECT-TYPE
SYNTAX Gauge32 (1..65535) SYNTAX RowPointer
UNITS "connections"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of connections that will be allowed
within this session."
::= { iscsiSessionAttributesEntry 17 }
iscsiSsnAuthMethod OBJECT-TYPE
SYNTAX AutonomousType
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object contains an OBJECT IDENTIFIER "This object contains a row in the IPS-AUTH MIB
which identifies the authentication method which identifies the authentication method
being used on this session, as communicated being used on this session, as communicated
during the login phase. during the login phase."
Some standardized values for this object are defined
within the ipsAuthMethodTypes subtree in the
IPS-AUTH MIB."
REFERENCE REFERENCE
"IPS-AUTH MIB" "IPS-AUTH MIB"
::= { iscsiSessionAttributesEntry 18 } ::= { iscsiSessionAttributesEntry 17 }
iscsiSsnDataSequenceInOrder OBJECT-TYPE iscsiSsnDataSequenceInOrder OBJECT-TYPE
SYNTAX TruthValue SYNTAX TruthValue
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"False indicates that iSCSI data PDU sequences may "False indicates that iSCSI data PDU sequences may
be transferred in any order. True indicates that be transferred in any order. True indicates that
data PDU sequences must be tranferred using data PDU sequences must be tranferred using
continuously increasing offsets, except during continuously increasing offsets, except during
error recovery." error recovery."
::= { iscsiSessionAttributesEntry 19 } ::= { iscsiSessionAttributesEntry 18 }
iscsiSsnDataPduInOrder OBJECT-TYPE iscsiSsnDataPduInOrder OBJECT-TYPE
SYNTAX TruthValue SYNTAX TruthValue
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"False indicates that iSCSI data PDUs within sequences "False indicates that iSCSI data PDUs within sequences
may be in any order. True indicates that data PDUs may be in any order. True indicates that data PDUs
within sequences must be at continuously increasing within sequences must be at continuously increasing
addresses, with no gaps or overlay between PDUs. addresses, with no gaps or overlay between PDUs.
Default is true." Default is true."
::= { iscsiSessionAttributesEntry 20 } ::= { iscsiSessionAttributesEntry 19 }
iscsiSsnLogoutLoginMaxTime OBJECT-TYPE
SYNTAX INTEGER (2..2600)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time, in seconds, for which the target will
keep connection and session state for possible
recovery after a connection termination or reset."
::= { iscsiSessionAttributesEntry 21 }
iscsiSsnErrorRecoveryLevel OBJECT-TYPE iscsiSsnErrorRecoveryLevel OBJECT-TYPE
SYNTAX INTEGER (0..255) SYNTAX INTEGER (0..255)
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The level of error recovery negotiated between "The level of error recovery negotiated between
the initiator and the target. Higher numbers the initiator and the target. Higher numbers
represent more detailed recovery schemes." represent more detailed recovery schemes."
::= { iscsiSessionAttributesEntry 22 } ::= { iscsiSessionAttributesEntry 20 }
-- Session Stats Table -- Session Stats Table
iscsiSessionStatsTable OBJECT-TYPE iscsiSessionStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiSessionStatsEntry SYNTAX SEQUENCE OF IscsiSessionStatsEntry
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A list of general iSCSI traffic counters for each of the "A list of general iSCSI traffic counters for each of the
sessions present on the system." sessions present on the system."
skipping to change at page 47, line 45 skipping to change at page 52, line 23
"The count of PDUs which were received on the session and "The count of PDUs which were received on the session and
contained header or data digest errors." contained header or data digest errors."
::= { iscsiSessionCxnErrorStatsEntry 1 } ::= { iscsiSessionCxnErrorStatsEntry 1 }
iscsiSsnCxnTimeoutErrors OBJECT-TYPE iscsiSsnCxnTimeoutErrors OBJECT-TYPE
SYNTAX Counter32 SYNTAX Counter32
UNITS "sequences" UNITS "sequences"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This is the count of sequences which exceeded their "The count of connections within this session
time limit." which have been terminated due to timeout."
::= { iscsiSessionCxnErrorStatsEntry 2 } ::= { iscsiSessionCxnErrorStatsEntry 2 }
---------------------------------------------------------------------- ----------------------------------------------------------------------
iscsiConnection OBJECT IDENTIFIER ::= { iscsiObjects 12 } iscsiConnection OBJECT IDENTIFIER ::= { iscsiObjects 12 }
-- Connection Attributes Table -- Connection Attributes Table
iscsiConnectionAttributesTable OBJECT-TYPE iscsiConnectionAttributesTable OBJECT-TYPE
SYNTAX SEQUENCE OF IscsiConnectionAttributesEntry SYNTAX SEQUENCE OF IscsiConnectionAttributesEntry
skipping to change at page 48, line 37 skipping to change at page 53, line 16
iscsiCxnIndex Unsigned32, iscsiCxnIndex Unsigned32,
iscsiCxnCid INTEGER, iscsiCxnCid INTEGER,
iscsiCxnState INTEGER, iscsiCxnState INTEGER,
iscsiCxnLocalAddrType InetAddressType, iscsiCxnLocalAddrType InetAddressType,
iscsiCxnLocalAddr InetAddress, iscsiCxnLocalAddr InetAddress,
iscsiCxnProtocol IscsiTransportProtocols, iscsiCxnProtocol IscsiTransportProtocols,
iscsiCxnLocalPort Unsigned32, iscsiCxnLocalPort Unsigned32,
iscsiCxnRemoteAddrType InetAddressType, iscsiCxnRemoteAddrType InetAddressType,
iscsiCxnRemoteAddr InetAddress, iscsiCxnRemoteAddr InetAddress,
iscsiCxnRemotePort Unsigned32, iscsiCxnRemotePort Unsigned32,
iscsiCxnDataPduLength INTEGER, iscsiCxnMaxRecvDataSegLength INTEGER,
iscsiCxnHeaderIntegrity AutonomousType, iscsiCxnHeaderIntegrity IscsiDigestMethod,
iscsiCxnDataIntegrity AutonomousType iscsiCxnDataIntegrity IscsiDigestMethod,
iscsiCxnRecvMarker TruthValue,
iscsiCxnSendMarker TruthValue
} }
iscsiCxnIndex OBJECT-TYPE iscsiCxnIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295) SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible MAX-ACCESS not-accessible
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"An arbitrary integer used to uniquely identify a "An arbitrary integer used to uniquely identify a
particular connection of a particular session within particular connection of a particular session within
an iSCSI instance present on the local system." an iSCSI instance present on the local system."
skipping to change at page 50, line 43 skipping to change at page 55, line 24
::= { iscsiConnectionAttributesEntry 9 } ::= { iscsiConnectionAttributesEntry 9 }
iscsiCxnRemotePort OBJECT-TYPE iscsiCxnRemotePort OBJECT-TYPE
SYNTAX Unsigned32 SYNTAX Unsigned32
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The remote transport protocol port used by this connection." "The remote transport protocol port used by this connection."
::= { iscsiConnectionAttributesEntry 10 } ::= { iscsiConnectionAttributesEntry 10 }
iscsiCxnDataPduLength OBJECT-TYPE iscsiCxnMaxRecvDataSegLength OBJECT-TYPE
SYNTAX INTEGER (0..33553920) SYNTAX INTEGER (512..16777215)
UNITS "bytes" UNITS "bytes"
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"The maximum data payload size supported for command "The maximum data payload size supported for command
or data PDUs within this session. or data PDUs in use within this connection.
Note that the size of reported in bytes even though Note that the size of reported in bytes even though
the negotiation is in 512k blocks." the negotiation is in 512k blocks."
DEFVAL { 8192 }
::= { iscsiConnectionAttributesEntry 11 } ::= { iscsiConnectionAttributesEntry 11 }
iscsiCxnHeaderIntegrity OBJECT-TYPE iscsiCxnHeaderIntegrity OBJECT-TYPE
SYNTAX AutonomousType SYNTAX IscsiDigestMethod
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object contains an OBJECT IDENTIFIER "This object identifies the iSCSI header
which identifies the iSCSI header digest scheme digest scheme in use within this connection."
in use within this session.
Some standardized values for this object are defined
within the iscsiHeaderIntegrityTypes subtree."
::= { iscsiConnectionAttributesEntry 12 } ::= { iscsiConnectionAttributesEntry 12 }
iscsiCxnDataIntegrity OBJECT-TYPE iscsiCxnDataIntegrity OBJECT-TYPE
SYNTAX AutonomousType SYNTAX IscsiDigestMethod
MAX-ACCESS read-only MAX-ACCESS read-only
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"This object contains an OBJECT IDENTIFIER "This object identifies the iSCSI data
which identifies the iSCSI data digest scheme digest scheme in use within this connection."
in use within this session.
Some standardized values for this object are defined
within the iscsiDataIntegrityTypes subtree."
::= { iscsiConnectionAttributesEntry 13 } ::= { iscsiConnectionAttributesEntry 13 }
iscsiCxnRecvMarker OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates whether or not this connection
is receiving markers in in its incoming data stream."
::= { iscsiConnectionAttributesEntry 14 }
iscsiCxnSendMarker OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates whether or not this connection
is inserting markers in in its outgoing data stream."
::= { iscsiConnectionAttributesEntry 15 }
------------------------------------------------------------------------ ------------------------------------------------------------------------
-- Notifications -- Notifications
iscsiNotificationsPrefix OBJECT IDENTIFIER ::= { iscsiNotifications 0 } iscsiNotificationsPrefix OBJECT IDENTIFIER ::= { iscsiNotifications 0 }
iscsiTgtLoginFailure NOTIFICATION-TYPE iscsiTgtLoginFailure NOTIFICATION-TYPE
OBJECTS { OBJECTS {
iscsiTgtLoginFailures, iscsiTgtLoginFailures,
iscsiTgtLastFailureType, iscsiTgtLastFailureType,
iscsiTgtLastIntrFailureName, iscsiTgtLastIntrFailureName,
skipping to change at page 53, line 36 skipping to change at page 58, line 27
errors that have caused a session failure for an errors that have caused a session failure for an
iSCSI instance." iSCSI instance."
::= { iscsiGroups 2 } ::= { iscsiGroups 2 }
iscsiPortalAttributesGroup OBJECT-GROUP iscsiPortalAttributesGroup OBJECT-GROUP
OBJECTS { OBJECTS {
iscsiPortalRowStatus, iscsiPortalRowStatus,
iscsiPortalRoles, iscsiPortalRoles,
iscsiPortalAddrType, iscsiPortalAddrType,
iscsiPortalAddr, iscsiPortalAddr,
iscsiPortalProtocol iscsiPortalProtocol,
iscsiPortalMaxRecvDataSegLength,
iscsiPortalPrimaryHdrDigest,
iscsiPortalPrimaryDataDigest,
iscsiPortalSecondaryHdrDigest,
iscsiPortalSecondaryDataDigest,
iscsiPortalRecvMarker
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A collection of objects providing information about "A collection of objects providing information about
the transport protocol endpoints of the local targets." the transport protocol endpoints of the local targets."
::= { iscsiGroups 3 } ::= { iscsiGroups 3 }
iscsiTgtPortalAttributesGroup OBJECT-GROUP iscsiTgtPortalAttributesGroup OBJECT-GROUP
OBJECTS { OBJECTS {
iscsiTgtPortalPort, iscsiTgtPortalPort,
skipping to change at page 54, line 22 skipping to change at page 59, line 20
DESCRIPTION DESCRIPTION
"A collection of objects providing information about "A collection of objects providing information about
the Internet Network Addresses of the local initiators." the Internet Network Addresses of the local initiators."
::= { iscsiGroups 5 } ::= { iscsiGroups 5 }
iscsiNodeAttributesGroup OBJECT-GROUP iscsiNodeAttributesGroup OBJECT-GROUP
OBJECTS { OBJECTS {
iscsiNodeName, iscsiNodeName,
iscsiNodeAlias, iscsiNodeAlias,
iscsiNodeRoles, iscsiNodeRoles,
iscsiNodeTransportType iscsiNodeTransportType,
iscsiNodeInitialR2T,
iscsiNodeBidiInitialR2T,
iscsiNodeImmediateData,
iscsiNodeMaxOutstandingR2T,
iscsiNodeFirstBurstSize,
iscsiNodeMaxBurstSize,
iscsiNodeMaxConnections,
iscsiNodeDataSequenceInOrder,
iscsiNodeDataPduInOrder,
iscsiNodeDefaultTime2Wait,
iscsiNodeDefaultTime2Retain,
iscsiNodeErrorRecoveryLevel
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A collection of objects providing information about all "A collection of objects providing information about all
local targets." local targets."
::= { iscsiGroups 6 } ::= { iscsiGroups 6 }
iscsiTargetAttributesGroup OBJECT-GROUP iscsiTargetAttributesGroup OBJECT-GROUP
OBJECTS { OBJECTS {
iscsiTgtLoginFailures, iscsiTgtLoginFailures,
skipping to change at page 55, line 26 skipping to change at page 60, line 36
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A collection of objects providing information about all "A collection of objects providing information about all
logout events between remote initiators to local targets." logout events between remote initiators to local targets."
::= { iscsiGroups 9 } ::= { iscsiGroups 9 }
iscsiTargetAuthGroup OBJECT-GROUP iscsiTargetAuthGroup OBJECT-GROUP
OBJECTS { OBJECTS {
iscsiTgtAuthRowStatus, iscsiTgtAuthRowStatus,
iscsiTgtAuthUser iscsiTgtAuthIdentity
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"." "."
::= { iscsiGroups 10 } ::= { iscsiGroups 10 }
iscsiInitiatorAttributesGroup OBJECT-GROUP iscsiInitiatorAttributesGroup OBJECT-GROUP
OBJECTS { OBJECTS {
iscsiIntrLoginFailures, iscsiIntrLoginFailures,
iscsiIntrLastFailureTime, iscsiIntrLastFailureTime,
skipping to change at page 56, line 29 skipping to change at page 61, line 38
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A collection of objects providing information about all "A collection of objects providing information about all
logout events between local initiators to remote targets." logout events between local initiators to remote targets."
::= { iscsiGroups 13 } ::= { iscsiGroups 13 }
iscsiInitiatorAuthGroup OBJECT-GROUP iscsiInitiatorAuthGroup OBJECT-GROUP
OBJECTS { OBJECTS {
iscsiIntrAuthRowStatus, iscsiIntrAuthRowStatus,
iscsiIntrAuthUser iscsiIntrAuthIdentity
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"." "."
::= { iscsiGroups 14 } ::= { iscsiGroups 14 }
iscsiSessionAttributesGroup OBJECT-GROUP iscsiSessionAttributesGroup OBJECT-GROUP
OBJECTS { OBJECTS {
iscsiSsnDirection, iscsiSsnDirection,
iscsiSsnInitiatorName, iscsiSsnInitiatorName,
iscsiSsnTargetName, iscsiSsnTargetName,
iscsiSsnTsid, iscsiSsnTsih,
iscsiSsnIsid, iscsiSsnIsid,
iscsiSsnInitiatorAlias, iscsiSsnInitiatorAlias,
iscsiSsnTargetAlias, iscsiSsnTargetAlias,
iscsiSsnInitialR2t, iscsiSsnInitialR2T,
iscsiSsnBidiInitialR2t, iscsiSsnBidiInitialR2T,
iscsiSsnImmediateData, iscsiSsnImmediateData,
iscsiSsnType, iscsiSsnType,
iscsiSsnMaxOutstandingR2t, iscsiSsnMaxOutstandingR2T,
iscsiSsnFirstBurstSize, iscsiSsnFirstBurstSize,
iscsiSsnMaxBurstSize, iscsiSsnMaxBurstSize,
iscsiSsnConnectionNumber, iscsiSsnConnectionNumber,
iscsiSsnMaxConnections, iscsiSsnAuthIdentity,
iscsiSsnAuthMethod,
iscsiSsnDataSequenceInOrder, iscsiSsnDataSequenceInOrder,
iscsiSsnDataPduInOrder, iscsiSsnDataPduInOrder,
iscsiSsnLogoutLoginMaxTime,
iscsiSsnErrorRecoveryLevel iscsiSsnErrorRecoveryLevel
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A collection of objects providing information applicable to "A collection of objects providing information applicable to
all sessions." all sessions."
::= { iscsiGroups 15 } ::= { iscsiGroups 15 }
iscsiSessionStatsGroup OBJECT-GROUP iscsiSessionStatsGroup OBJECT-GROUP
OBJECTS { OBJECTS {
skipping to change at page 58, line 5 skipping to change at page 63, line 12
OBJECTS { OBJECTS {
iscsiCxnCid, iscsiCxnCid,
iscsiCxnState, iscsiCxnState,
iscsiCxnProtocol, iscsiCxnProtocol,
iscsiCxnLocalAddrType, iscsiCxnLocalAddrType,
iscsiCxnLocalAddr, iscsiCxnLocalAddr,
iscsiCxnLocalPort, iscsiCxnLocalPort,
iscsiCxnRemoteAddrType, iscsiCxnRemoteAddrType,
iscsiCxnRemoteAddr, iscsiCxnRemoteAddr,
iscsiCxnRemotePort, iscsiCxnRemotePort,
iscsiCxnDataPduLength, iscsiCxnMaxRecvDataSegLength,
iscsiCxnHeaderIntegrity, iscsiCxnHeaderIntegrity,
iscsiCxnDataIntegrity iscsiCxnDataIntegrity,
iscsiCxnRecvMarker,
iscsiCxnSendMarker
} }
STATUS current STATUS current
DESCRIPTION DESCRIPTION
"A collection of objects providing information about all "A collection of objects providing information about all
connections used by all sessions." connections used by all sessions."
::= { iscsiGroups 18 } ::= { iscsiGroups 18 }
iscsiTgtLgnNotificationsGroup NOTIFICATION-GROUP iscsiTgtLgnNotificationsGroup NOTIFICATION-GROUP
NOTIFICATIONS { NOTIFICATIONS {
iscsiTgtLoginFailure iscsiTgtLoginFailure
skipping to change at page 61, line 31 skipping to change at page 66, line 39
features as provided by the SNMPv3 framework. Specifically, the use features as provided by the SNMPv3 framework. Specifically, the use
of the User-based Security Model RFC 2574 [RFC2574] and the View- of the User-based Security Model RFC 2574 [RFC2574] and the View-
based Access Control Model RFC 2575 [RFC2575] is recommended. based Access Control Model RFC 2575 [RFC2575] is recommended.
It is then a customer/user responsibility to ensure that the SNMP It is then a customer/user responsibility to ensure that the SNMP
entity giving access to an instance of this MIB, is properly entity giving access to an instance of this MIB, is properly
configured to give access to the objects only to those principals configured to give access to the objects only to those principals
(users) that have legitimate rights to indeed GET or SET (users) that have legitimate rights to indeed GET or SET
(change/create/delete) them. (change/create/delete) them.
9. References 9. Normative References
[ISCSI] Satran, J., et. al., "iSCSI", draft-ietf-ips-iSCSI-10, [ISCSI] Satran, J., et. al., "iSCSI", draft-ietf-ips-iSCSI-13, June
January 2002. 2002.
[RFC2571] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture [RFC2571] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture
for Describing SNMP Management Frameworks", RFC 2571, April for Describing SNMP Management Frameworks", RFC 2571, April
1999. 1999.
[RFC1155] Rose, M., and K. McCloghrie, "Structure and Identification [RFC1155] Rose, M., and K. McCloghrie, "Structure and Identification
of Management Information for TCP/IP-based Internets", STD of Management Information for TCP/IP-based Internets", STD
16, RFC 1155, May 1990. 16, RFC 1155, May 1990.
[RFC1212] Rose, M., and K. McCloghrie, "Concise MIB Definitions", STD [RFC1212] Rose, M., and K. McCloghrie, "Concise MIB Definitions", STD
16, RFC 1212, March 1991. 16, RFC 1212, March 1991.
[RFC1215] M. Rose, "A Convention for Defining Traps for use with the
SNMP", RFC 1215, March 1991.
[RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., [RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M., and S. Waldbusser, "Structure of Management Rose, M., and S. Waldbusser, "Structure of Management
Information Version 2 (SMIv2)", STD 58, RFC 2578, April Information Version 2 (SMIv2)", STD 58, RFC 2578, April
1999. 1999.
[RFC1215] M. Rose, "A Convention for Defining Traps for use with the
SNMP", RFC 1215, March 1991.
[RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., [RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M., and S. Waldbusser, "Textual Conventions for Rose, M., and S. Waldbusser, "Textual Conventions for
SMIv2", STD 58, RFC 2579, April 1999. SMIv2", STD 58, RFC 2579, April 1999.
[RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., [RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
Rose, M., and S. Waldbusser, "Conformance Statements for Rose, M., and S. Waldbusser, "Conformance Statements for
SMIv2", STD 58, RFC 2580, April 1999. SMIv2", STD 58, RFC 2580, April 1999.
[RFC1157] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple [RFC1157] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple
Network Management Protocol", STD 15, RFC 1157, May 1990. Network Management Protocol", STD 15, RFC 1157, May 1990.
[RFC3291] Daniele, M., et. al., "Textual Conventions for Internet
Network Addresses", RFC 3291, May 2002.
[SCSI-MIB] Hallak-Stamler, M., et. al., "Definitions of Managed Objects
for SCSI Entities", draft-ietf-ips-scsi-mib-03.txt, June
2002.
[AUTH-MIB] Bakke, M., et. al., "Definitions of Managed Objects for User
Identity Authentication", draft-ietf-ips-auth-mib-01.txt,
June 2002.
10. Informative References
[RFC1901] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, [RFC1901] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Introduction to Community-based SNMPv2", RFC 1901, January "Introduction to Community-based SNMPv2", RFC 1901, January
1996. 1996.
[RFC1906] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, [RFC1906] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Transport Mappings for Version 2 of the Simple Network "Transport Mappings for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1906, January 1996. Management Protocol (SNMPv2)", RFC 1906, January 1996.
[RFC2572] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message [RFC2572] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message
Processing and Dispatching for the Simple Network Management Processing and Dispatching for the Simple Network Management
skipping to change at page 63, line 8 skipping to change at page 68, line 31
"Introduction to Version 3 of the Internet-standard Network "Introduction to Version 3 of the Internet-standard Network
Management Framework", RFC 2570, April 1999. Management Framework", RFC 2570, April 1999.
[RFC2012] McCloghrie, K., "SNMPv2 Management Information Base for the [RFC2012] McCloghrie, K., "SNMPv2 Management Information Base for the
Transmission Control Protocol using SMIv2", RFC 2012, Transmission Control Protocol using SMIv2", RFC 2012,
November 1996. November 1996.
[RFC2851] Daniele, M., et. al., "Textual Conventions for Internet [RFC2851] Daniele, M., et. al., "Textual Conventions for Internet
Network Addresses", RFC 2851, June 2000. Network Addresses", RFC 2851, June 2000.
[IPV6MIB] Daniele, M., et. al., "Textual Conventions for Internet 11. Authors' Addresses
Network Addresses", draft-ietf-ops-rfc2851-update-06.txt,
December 2001.
[SCSI-MIB] Hallak-Stamler, M., et. al., "Definitions of Managed Objects
for SCSI Entities", draft-ietf-ips-scsi-mib-02.txt, February
2002.
[AUTH-MIB] Bakke, M., et. al., "Definitions of Managed Objects for User
Identity Authentication", draft-ietf-ips-auth-mib-00.txt,
February 2002.
10. Authors' Addresses
Mark Bakke Mark Bakke
Postal: Cisco Systems, Inc Postal: Cisco Systems, Inc
6450 Wedgwood Road, Suite 130 6450 Wedgwood Road, Suite 130
Maple Grove, MN Maple Grove, MN
USA 55311 USA 55311
Tel: +1 763-398-1000 Tel: +1 763-398-1000
Fax: +1 763-398-1001 Fax: +1 763-398-1001
 End of changes. 

This html diff was produced by rfcdiff 1.23, available from http://www.levkowetz.com/ietf/tools/rfcdiff/