draft-ietf-issll-is802-sbm-08.txt   draft-ietf-issll-is802-sbm-09.txt 
Internet Engineering Task Force Raj Yavatkar, Intel Internet Engineering Task Force Raj Yavatkar, Intel
INTERNET-DRAFT Don Hoffman, Teledesic INTERNET-DRAFT Don Hoffman, Teledesic
Yoram Bernet, Microsoft Yoram Bernet, Microsoft
Fred Baker, Cisco Fred Baker, Cisco
draft-ietf-issll-is802-sbm-08.txt Michael Speer, Sun Microsystems Michael Speer, Sun Microsystems
October 1999
SBM (Subnet Bandwidth Manager): SBM (Subnet Bandwidth Manager):
A Protocol for RSVP-based Admission Control over IEEE 802-style networks A Protocol for RSVP-based Admission Control over IEEE 802-style networks
Status of this Memo Status of this Memo
This document is an Internet-Draft and is in full conformance with all This document is an Internet-Draft and is in full conformance with all
provisions of Section 10 of RFC2026. provisions of Section 10 of RFC2026.
This document is an Internet Draft. Internet Drafts are working This document is an Internet Draft. Internet Drafts are working
documents of the Internet Engineering Task Force (IETF), its areas, documents of the Internet Engineering Task Force (IETF), its areas,
skipping to change at page 2, line 5 skipping to change at page 2, line 5
and may be updated, replaced, or obsoleted by other documents at any and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet Drafts as reference time. It is inappropriate to use Internet Drafts as reference
material or to cite them other than as ``work in progress.'' material or to cite them other than as ``work in progress.''
The list of current Internet-Drafts can be accessed at The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html. http://www.ietf.org/shadow.html.
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
Abstract Abstract
This document describes a signaling method and protocol for RSVP-based This document describes a signaling method and protocol for RSVP-based
admission control over IEEE 802-style LANs. The protocol is designed admission control over IEEE 802-style LANs. The protocol is designed
to work both with the current generation of IEEE 802 LANs as well as with the to work both with the current generation of IEEE 802 LANs as well as with the
recent work completed by the IEEE 802.1 committee. recent work completed by the IEEE 802.1 committee.
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
1. Introduction 1. Introduction
New extensions to the Internet architecture and service models have New extensions to the Internet architecture and service models have
been defined for an integrated services Inernet [RFC-1633, RFC-2205, been defined for an integrated services Internet [RFC-1633, RFC-2205,
RFC-2210] so that applications can request specific qualities or lev- RFC-2210] so that applications can request specific qualities or lev-
els of service from an internetwork in addition to the current IP els of service from an internetwork in addition to the current IP
best-effort service. These extensions include RSVP, a resource reser- best-effort service. These extensions include RSVP, a resource reser-
vation setup protocol, and definition of new service classes to be vation setup protocol, and definition of new service classes to be
supported by Integrated Services routers. RSVP and service class supported by Integrated Services routers. RSVP and service class
definitions are largely independent of the underlying networking tech- definitions are largely independent of the underlying networking tech-
nologies and it is necessary to define the mapping of RSVP and nologies and it is necessary to define the mapping of RSVP and
Integrated Services specifications onto specific subnetwork technolo- Integrated Services specifications onto specific subnetwork technolo-
gies. For example, a definition of service mappings and reservation gies. For example, a definition of service mappings and reservation
setup protocols is needed for specific link-layer technologies such as setup protocols is needed for specific link-layer technologies such as
shared and switched IEEE-802-style LAN technologies. shared and switched IEEE-802-style LAN technologies.
This document defines SBM, a signaling protocol for RSVP-based admis- This document defines SBM, a signaling protocol for RSVP-based admis-
sion control over IEEE 802-style networks. SBM provides a method for sion control over IEEE 802-style networks. SBM provides a method for
mapping an internet-level setup protocol such as RSVP onto IEEE 802- mapping an internet-level setup protocol such as RSVP onto IEEE 802-
style networks. In particular, it describes the operation of RSVP- style networks. In particular, it describes the operation of RSVP-
enabled hosts/routers and link layer devices (switches, bridges) to enabled hosts/routers and link layer devices (switches, bridges) to
support reservation of LAN resources for RSVP-enabled data flows. A support reservation of LAN resources for RSVP-enabled data flows. A
framework for providing Integrated Services over shared and switched framework for providing Integrated Services over shared and switched
IEEE-802-style LAN technologies and a definition of service mappings IEEE-802-style LAN technologies and a definition of service mappings
have been described in separate documents [Ghanwani98, Seaman98]. have been described in separate documents [RFC-FRAME, RFC-MAP].
2. Goals and Assumptions 2. Goals and Assumptions
The SBM (Subnet Bandwidth Manager) protocol and its use for admission The SBM (Subnet Bandwidth Manager) protocol and its use for admission
control and bandwidth management in IEEE 802 level-2 networks is based control and bandwidth management in IEEE 802 level-2 networks is based
on the following architectural goals and assumptions: on the following architectural goals and assumptions:
I. Even though the current trend is towards increased use of I. Even though the current trend is towards increased use of
switched LAN topologies consisting of newer switches that support switched LAN topologies consisting of newer switches that support
the priority queuing mechanisms specified by IEEE 802.1p, we the priority queuing mechanisms specified by IEEE 802.1p, we
assume that the LAN technologies will continue to be a mix of assume that the LAN technologies will continue to be a mix of
legacy shared/ switched LAN segments and newer switched segments legacy shared/ switched LAN segments and newer switched segments
based on IEEE 802.1p specification. Therefore, we specify a sig- based on IEEE 802.1p specification. Therefore, we specify a sig-
naling protocol for managing bandwidth over both legacy and newer naling protocol for managing bandwidth over both legacy and newer
LAN topologies and that takes advantage of the additional func- LAN topologies and that takes advantage of the additional func-
tionality (such as an explicit support for different traffic tionality (such as an explicit support for different traffic
classes or integrated service classes) as it becomes available in classes or integrated service classes) as it becomes available in
the new generation of switches, hubs, or bridges. As a result, the new generation of switches, hubs, or bridges. As a result,
the SBM protocol would allow for a range of LAN bandwidth the SBM protocol would allow for a range of LAN bandwidth
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
management solutions that vary from one that exercises purely management solutions that vary from one that exercises purely
administrative control (over the amount of bandwidth consumed by administrative control (over the amount of bandwidth consumed by
RSVP-enabled traffic flows) to one that requires cooperation (and RSVP-enabled traffic flows) to one that requires cooperation (and
enforcement) from all the end-systems or switches in a IEEE 802 enforcement) from all the end-systems or switches in a IEEE 802
LAN. LAN.
II. This document specifies only a signaling method and protocol for II. This document specifies only a signaling method and protocol for
LAN-based admission control over RSVP flows. We do not define LAN-based admission control over RSVP flows. We do not define
here any traffic control mechanisms for the link layer; the pro- here any traffic control mechanisms for the link layer; the pro-
skipping to change at page 5, line 5 skipping to change at page 5, line 5
parameter in Appendix C). Second, the best-effort traffic gen- parameter in Appendix C). Second, the best-effort traffic gen-
erated by the TCP/IP-based traffic sources is generally rate- erated by the TCP/IP-based traffic sources is generally rate-
adaptive (using a TCP-style "slow start" congestion avoidance adaptive (using a TCP-style "slow start" congestion avoidance
mechanism or a feedback-based rate adaptation mechanism used by mechanism or a feedback-based rate adaptation mechanism used by
audio/video streams based on RTP/RTCP protocols) and adapts to audio/video streams based on RTP/RTCP protocols) and adapts to
stay within the available network bandwidth. Thus, the combina- stay within the available network bandwidth. Thus, the combina-
tion of admission control and rate adaptation should avoid per- tion of admission control and rate adaptation should avoid per-
sistent traffic congestion. This does not, however, guarantee sistent traffic congestion. This does not, however, guarantee
that non-Integrated-Services traffic will not interfere with the that non-Integrated-Services traffic will not interfere with the
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
Integrated Services traffic in the absence of traffic control Integrated Services traffic in the absence of traffic control
support in the underlying LAN infrastructure. support in the underlying LAN infrastructure.
3. Organization of the rest of this document 3. Organization of the rest of this document
The rest of this document provides a detailed description of the SBM- The rest of this document provides a detailed description of the SBM-
based admission control procedure(s) for IEEE 802 LAN technologies. based admission control procedure(s) for IEEE 802 LAN technologies.
The document is organized as follows: The document is organized as follows:
skipping to change at page 6, line 5 skipping to change at page 6, line 5
* Appendix B specifies the formats of SBM-specific messages used * Appendix B specifies the formats of SBM-specific messages used
and the formats of new RSVP objects needed for the SBM operation. and the formats of new RSVP objects needed for the SBM operation.
* Appendix C describes usage of the DSBM to distribute configura- * Appendix C describes usage of the DSBM to distribute configura-
tion information to senders on a managed segment. tion information to senders on a managed segment.
4. Overview 4. Overview
4.1. Definitions 4.1. Definitions
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
- Link Layer or Layer 2 or L2: We refer to data-link layer techno- - Link Layer or Layer 2 or L2: We refer to data-link layer techno-
logies such as IEEE 802.3/Ethernet as L2 or layer 2. logies such as IEEE 802.3/Ethernet as L2 or layer 2.
- Link Layer Domain or Layer 2 domain or L2 domain: a set of nodes - Link Layer Domain or Layer 2 domain or L2 domain: a set of nodes
and links interconnected without passing through a L3 forwarding and links interconnected without passing through a L3 forwarding
function. One or more IP subnets can be overlaid on a L2 domain. function. One or more IP subnets can be overlaid on a L2 domain.
- Layer 2 or L2 devices: We refer to devices that only implement - Layer 2 or L2 devices: We refer to devices that only implement
Layer 2 functionality as Layer 2 or L2 devices. These include Layer 2 functionality as Layer 2 or L2 devices. These include
skipping to change at page 7, line 5 skipping to change at page 7, line 5
- Traffic Class: An aggregation of data flows which are given simi- - Traffic Class: An aggregation of data flows which are given simi-
lar service within a switched network. lar service within a switched network.
- User_priority: User_priority is a value associated with the - User_priority: User_priority is a value associated with the
transmission and reception of all frames in the IEEE 802 service transmission and reception of all frames in the IEEE 802 service
model: it is supplied by the sender that is using the MAC ser- model: it is supplied by the sender that is using the MAC ser-
vice. It is provided along with the data to a receiver using the vice. It is provided along with the data to a receiver using the
MAC service. It may or may not be actually carried over the MAC service. It may or may not be actually carried over the
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
network: Token-Ring/802.5 carries this value (encoded in its FC network: Token-Ring/802.5 carries this value (encoded in its FC
octet), basic Ethernet/802.3 does not, 802.12 may or may not octet), basic Ethernet/802.3 does not, 802.12 may or may not
depending on the frame format in use. 802.1p defines a consistent depending on the frame format in use. 802.1p defines a consistent
way to carry this value over the bridged network on Ethernet, way to carry this value over the bridged network on Ethernet,
Token Ring, Demand-Priority, FDDI or other MAC-layer media using Token Ring, Demand-Priority, FDDI or other MAC-layer media using
an extended frame format. The usage of user_priority is fully an extended frame format. The usage of user_priority is fully
described in section 2.5 of 802.1D [IEEE8021D] and 802.1p described in section 2.5 of 802.1D [IEEE8021D] and 802.1p
[IEEE8021P] "Support of the Internal Layer Service by Specific [IEEE8021P] "Support of the Internal Layer Service by Specific
MAC Procedures". MAC Procedures".
skipping to change at page 8, line 5 skipping to change at page 8, line 5
interconnected by layer 2 devices, constitute an extended seg- interconnected by layer 2 devices, constitute an extended seg-
ment. ment.
- Managed L2 domain: An L2 domain consisting of managed segments is - Managed L2 domain: An L2 domain consisting of managed segments is
referred to as a managed L2 domain to distinguish it from a L2 referred to as a managed L2 domain to distinguish it from a L2
domain with no DSBMs present for exercising admission control domain with no DSBMs present for exercising admission control
over resources at segments in the L2 domain. over resources at segments in the L2 domain.
- DSBM clients: These are entities that transmit traffic onto a - DSBM clients: These are entities that transmit traffic onto a
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
managed segment and use the services of a DSBM for the managed managed segment and use the services of a DSBM for the managed
segment for admission control over a LAN segment. Only the layer segment for admission control over a LAN segment. Only the layer
3 or higher layer entities on L3 devices such as hosts and 3 or higher layer entities on L3 devices such as hosts and
routers are expected to send traffic that requires resource routers are expected to send traffic that requires resource
reservations, and, therefore, DSBM clients are L3 entities. reservations, and, therefore, DSBM clients are L3 entities.
- SBM transparent devices: A "SBM transparent" device is unaware of - SBM transparent devices: A "SBM transparent" device is unaware of
SBMs or DSBMs (though it may or may not be RSVP aware) and, SBMs or DSBMs (though it may or may not be RSVP aware) and,
therefore, does not participate in the SBM-based admission con- therefore, does not participate in the SBM-based admission con-
skipping to change at page 9, line 5 skipping to change at page 9, line 5
the segment. The procedure for dynamically electing the DSBM is the segment. The procedure for dynamically electing the DSBM is
described in Appendix A. The only other approved method for specifying described in Appendix A. The only other approved method for specifying
a DSBM for a managed segment is static configuration at SBM-capable a DSBM for a managed segment is static configuration at SBM-capable
devices. devices.
The presence of a DSBM makes the segment a "managed segment". Some- The presence of a DSBM makes the segment a "managed segment". Some-
times, two or more L2 segments may be interconnected by SBM tran- times, two or more L2 segments may be interconnected by SBM tran-
sparent devices. In that case, a single DSBM will manage the resources sparent devices. In that case, a single DSBM will manage the resources
for those segments treating the collection of such segments as a for those segments treating the collection of such segments as a
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
single managed segment for the purpose of admission control. single managed segment for the purpose of admission control.
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
4.2.1. Basic Algorithm 4.2.1. Basic Algorithm
Figure 1 - An Example of a Managed Segment. Figure 1 - An Example of a Managed Segment.
+-------+ +-----+ +------+ +-----+ +--------+ +-------+ +-----+ +------+ +-----+ +--------+
|Router | | Host| | DSBM | | Host| | Router | |Router | | Host| | DSBM | | Host| | Router |
| R2 | | C | +------+ | B | | R3 | | R2 | | C | +------+ | B | | R3 |
+-------+ +-----+ / +-----+ +--------+ +-------+ +-----+ / +-----+ +--------+
| | / | | | | / | |
skipping to change at page 11, line 5 skipping to change at page 11, line 5
knowledge of link topology allow discovery of link capacity, the knowledge of link topology allow discovery of link capacity, the
configuration may be necessary to limit the fraction of link configuration may be necessary to limit the fraction of link
capacity that can be reserved on a link. Configuration is likely capacity that can be reserved on a link. Configuration is likely
to be static with the current L2/L3 devices. Future work may to be static with the current L2/L3 devices. Future work may
allow for dynamic discovery of this information. This document allow for dynamic discovery of this information. This document
does not specify the configuration mechanism. does not specify the configuration mechanism.
2. DSBM Client Initialization: For each interface attached, a DSBM 2. DSBM Client Initialization: For each interface attached, a DSBM
client determines whether a DSBM exists on the interface. The client determines whether a DSBM exists on the interface. The
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
procedure for discovering and verifying the existence of the DSBM procedure for discovering and verifying the existence of the DSBM
for an attached segment is described in Appendix A. If the client for an attached segment is described in Appendix A. If the client
itself is capable of serving as the DSBM on the segment, it may itself is capable of serving as the DSBM on the segment, it may
choose to participate in the election to become the DSBM. At the choose to participate in the election to become the DSBM. At the
start, a DSBM client first verifies that a DSBM exists in its L2 start, a DSBM client first verifies that a DSBM exists in its L2
domain so that it can communicate with the DSBM for admission domain so that it can communicate with the DSBM for admission
control purposes. control purposes.
In the case of a full-duplex segment, an election may not be In the case of a full-duplex segment, an election may not be
skipping to change at page 12, line 5 skipping to change at page 12, line 5
tion 5). In the process, the DSBM builds the PATH state, tion 5). In the process, the DSBM builds the PATH state,
remembers the router R1 (its L2 and l3 addresses) as the previ- remembers the router R1 (its L2 and l3 addresses) as the previ-
ous hop for the session, puts its own L2 and L3 addresses in ous hop for the session, puts its own L2 and L3 addresses in
the PHOP objects (see explanation later), and effectively the PHOP objects (see explanation later), and effectively
inserts itself as an intermediate node between the sender (or inserts itself as an intermediate node between the sender (or
R1 in Figure 1) and the receiver (host A) on the managed seg- R1 in Figure 1) and the receiver (host A) on the managed seg-
ment. ment.
b) When an application on host A wishes to make a reservation for b) When an application on host A wishes to make a reservation for
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
the RSVP session, host A follows the standard RSVP message pro- the RSVP session, host A follows the standard RSVP message pro-
cessing rules and sends a RSVP RESV message to the previous hop cessing rules and sends a RSVP RESV message to the previous hop
L2/L3 address (the DSBMs address) obtained from the PHOP L2/L3 address (the DSBMs address) obtained from the PHOP
object(s) in the previously received PATH message. object(s) in the previously received PATH message.
c) The DSBM processes the RSVP RESV message based on the bandwidth c) The DSBM processes the RSVP RESV message based on the bandwidth
available and returns an RESVERR message to the requester (host available and returns an RESV_ERR message to the requester (host
A) if the request cannot be granted. If sufficient resources A) if the request cannot be granted. If sufficient resources
are available and the reservation request is granted, the DSBM are available and the reservation request is granted, the DSBM
forwards the RESV message towards the PHOP(s) based on its forwards the RESV message towards the PHOP(s) based on its
local PATH state for the session. The DSBM merges reservation local PATH state for the session. The DSBM merges reservation
requests for the same session as and when possible using the requests for the same session as and when possible using the
rules similar to those used in the conventional RSVP processing rules similar to those used in the conventional RSVP processing
(except for an additional criterion described in Section 5.9). (except for an additional criterion described in Section 5.9).
d) If the L2 domain contains more than one managed segment, the d) If the L2 domain contains more than one managed segment, the
requester (host A) and the forwarder (router R1) may be requester (host A) and the forwarder (router R1) may be
skipping to change at page 13, line 5 skipping to change at page 13, line 5
outgoing PATH messages on a managed segment are sent to the DSBM for outgoing PATH messages on a managed segment are sent to the DSBM for
the corresponding managed segment (Section 5.2 describes how the PATH the corresponding managed segment (Section 5.2 describes how the PATH
messages are sent to the DSBM on a managed segment). messages are sent to the DSBM on a managed segment).
4.2.2.2 The LAN_NHOP Objects 4.2.2.2 The LAN_NHOP Objects
In conventional RSVP processing over point-to-point links, RSVP nodes In conventional RSVP processing over point-to-point links, RSVP nodes
(hosts/routers) use RSVP_HOP object (NHOP and PHOP info) to keep track (hosts/routers) use RSVP_HOP object (NHOP and PHOP info) to keep track
of the next hop (downstream node in the path of data packets in a of the next hop (downstream node in the path of data packets in a
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
traffic flow) and the previous hop (upstream nodes with respect to the traffic flow) and the previous hop (upstream nodes with respect to the
data flow) nodes on the path between a sender and a receiver. Routers data flow) nodes on the path between a sender and a receiver. Routers
along the path of a PATH message forward the message towards the des- along the path of a PATH message forward the message towards the des-
tination address based on the L3 routing (packet forwarding) tables. tination address based on the L3 routing (packet forwarding) tables.
For example, consider the L2 domain in Figure 1. Assume that both the For example, consider the L2 domain in Figure 1. Assume that both the
sender (some host X) and the receiver (some host Y) in a RSVP session sender (some host X) and the receiver (some host Y) in a RSVP session
reside outside the L2 domain shown in the Figure, but PATH messages reside outside the L2 domain shown in the Figure, but PATH messages
from the sender to its receiver pass through the routers in the L2 from the sender to its receiver pass through the routers in the L2
skipping to change at page 14, line 5 skipping to change at page 14, line 5
PATH message. R1 first determines that R2 is the next hop router (or PATH message. R1 first determines that R2 is the next hop router (or
the egress node in the L2 domain for the session address) and then the egress node in the L2 domain for the session address) and then
inserts a LAN_NHOP object that specifies R2's IP address. When a DSBM inserts a LAN_NHOP object that specifies R2's IP address. When a DSBM
receives a PATH message, it can now look at the address in the receives a PATH message, it can now look at the address in the
LAN_NHOP object and forward the PATH message towards the egress node LAN_NHOP object and forward the PATH message towards the egress node
after processing the PATH message. However, we expect the L2 devices after processing the PATH message. However, we expect the L2 devices
(such as switches) to act as DSBMs on the path within the L2 domain (such as switches) to act as DSBMs on the path within the L2 domain
and it may not be reasonable to expect these devices to have an ARP and it may not be reasonable to expect these devices to have an ARP
capability to determine the MAC address (we call it L2ADDR for Layer 2 capability to determine the MAC address (we call it L2ADDR for Layer 2
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
address) corresponding to the IP address in the LAN_NHOP object. address) corresponding to the IP address in the LAN_NHOP object.
Therefore, we require that the LAN_NHOP information (generated by the Therefore, we require that the LAN_NHOP information (generated by the
L3 device) include both the IP address (LAN_NHOP_L3 address) and the L3 device) include both the IP address (LAN_NHOP_L3 address) and the
corresponding MAC address (LAN_NHOP_L2 address ) for the next L3 hop corresponding MAC address (LAN_NHOP_L2 address ) for the next L3 hop
over the L2 domain. The LAN_NHOP_L3 address is used by SBM protocol over the L2 domain. The LAN_NHOP_L3 address is used by SBM protocol
entities on L3 devices to forward the PATH message towards its desti- entities on L3 devices to forward the PATH message towards its desti-
nation whereas the L2 address is used by the SBM protocol entities on nation whereas the L2 address is used by the SBM protocol entities on
L2 devices to determine how to forward the PATH message towards the L3 L2 devices to determine how to forward the PATH message towards the L3
skipping to change at page 14, line 39 skipping to change at page 14, line 39
the DSBM inserts itself as an intermediate hop in the chain of the DSBM inserts itself as an intermediate hop in the chain of
nodes in the path between two L3 nodes across the L2 domain. nodes in the path between two L3 nodes across the L2 domain.
- The PATH state in a DSBM is used for forwarding subsequent RESV - The PATH state in a DSBM is used for forwarding subsequent RESV
messages as per the standard RSVP message processing rules. When messages as per the standard RSVP message processing rules. When
the DSBM receives a RESV message, it processes the message and the DSBM receives a RESV message, it processes the message and
forwards it to appropriate PHOP(s) based on its PATH state. forwards it to appropriate PHOP(s) based on its PATH state.
- Because a DSBM inserts itself as a hop between two RSVP nodes in - Because a DSBM inserts itself as a hop between two RSVP nodes in
the path of a RSVP flow, all RSVP related messages (such as PATH, the path of a RSVP flow, all RSVP related messages (such as PATH,
PATH_TEAR, RESV, RESV_CONFM, RESV_TEAR, and RESV_ERR) now flow PATH_TEAR, RESV, RESV_CONF, RESV_TEAR, and RESV_ERR) now flow
through the DSBM. In particular, a PATH_TEAR message is routed through the DSBM. In particular, a PATH_TEAR message is routed
exactly through the intermediate DSBM(s) as its corresponding exactly through the intermediate DSBM(s) as its corresponding
PATH message and the local PATH state is first cleaned up at each PATH message and the local PATH state is first cleaned up at each
intermediate hop before the PATH_TEAR message gets forwarded. intermediate hop before the PATH_TEAR message gets forwarded.
- So far, we have described how the PATH message propagates through - So far, we have described how the PATH message propagates through
the L2 domain establishing PATH state at each DSBM along the the L2 domain establishing PATH state at each DSBM along the
managed segments in the path. The layer 2 address (LAN_NHOP_L2 managed segments in the path. The layer 2 address (LAN_NHOP_L2
address) in the LAN_NHOP object should be used by the L2 devices address) in the LAN_NHOP object should be used by the L2 devices
along the path to decide how to forward the PATH message toward along the path to decide how to forward the PATH message toward
the next L3 hop. Such devices will apply the standard IEEE the next L3 hop. Such devices will apply the standard IEEE
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
802.1D forwarding rules (e.g., send it on a single port based on 802.1D forwarding rules (e.g., send it on a single port based on
its filtering database, or flood it on all ports active in the its filtering database, or flood it on all ports active in the
spanning tree if the L2 address does not appear in the filtering spanning tree if the L2 address does not appear in the filtering
database) to the LAN_NHOP_L2 address as are applied normally to database) to the LAN_NHOP_L2 address as are applied normally to
data packets destined to the address. data packets destined to the address.
4.2.2.5 Including Both Layer-2 and Layer-3 Addresses in the 4.2.2.5 Including Both Layer-2 and Layer-3 Addresses in the
RSVP_HOP Objects RSVP_HOP Objects
skipping to change at page 16, line 5 skipping to change at page 16, line 5
PATH state and then overwrites the RSVP_HOP and RSVP_HOP_L2 objects PATH state and then overwrites the RSVP_HOP and RSVP_HOP_L2 objects
with its own addresses before forwarding the PATH message over a with its own addresses before forwarding the PATH message over a
managed segment. managed segment.
The exact format of RSVP_HOP_L2 object is specified in Appendix B. The exact format of RSVP_HOP_L2 object is specified in Appendix B.
4.2.2.6 Loop Detection 4.2.2.6 Loop Detection
When an RSVP session address is a multicast address and a SBM, DSBM, When an RSVP session address is a multicast address and a SBM, DSBM,
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
and DSBM clients share the same L2 segment (a shared segment), it is and DSBM clients share the same L2 segment (a shared segment), it is
possible for a SBM or a DSBM client to receive one or more copies of a possible for a SBM or a DSBM client to receive one or more copies of a
PATH message that it forwarded earlier when a DSBM on the same wire PATH message that it forwarded earlier when a DSBM on the same wire
forwards it (See Section 5.8 for an example of such a case). To facil- forwards it (See Section 5.8 for an example of such a case). To facil-
itate detection of such loops, we use a new RSVP object called the itate detection of such loops, we use a new RSVP object called the
LAN_LOOPBACK object. DSBM clients or SBMs (but not the DSBMs reflect- LAN_LOOPBACK object. DSBM clients or SBMs (but not the DSBMs reflect-
ing a PATH message onto the interface over which it arrived earlier) ing a PATH message onto the interface over which it arrived earlier)
must overwrite (or add if the PATH message does NOT already include a must overwrite (or add if the PATH message does NOT already include a
LAN_LOOPBACK object) the LAN_LOOPBACK object in the PATH message with LAN_LOOPBACK object) the LAN_LOOPBACK object in the PATH message with
skipping to change at page 16, line 44 skipping to change at page 16, line 44
several "user_priority" values encoded in packets representing dif- several "user_priority" values encoded in packets representing dif-
ferent traffic classes (see [IEEE802Q, IEEE8021p] for further ferent traffic classes (see [IEEE802Q, IEEE8021p] for further
details). The user_priority values can be encoded either in native LAN details). The user_priority values can be encoded either in native LAN
packets (e.g., in IEEE 802.5's FC octet) or by using an encapsulation packets (e.g., in IEEE 802.5's FC octet) or by using an encapsulation
above the MAC layer (e.g., in the case of Ethernet, the user_priority above the MAC layer (e.g., in the case of Ethernet, the user_priority
value assigned to each packet will be carried in the frame header value assigned to each packet will be carried in the frame header
using the new, extended frame format defined by IEEE 802.1Q using the new, extended frame format defined by IEEE 802.1Q
[IEEE8021Q]. IEEE, however, makes no recommendations about how a [IEEE8021Q]. IEEE, however, makes no recommendations about how a
sender or network should use the user_priority values. An accompanying sender or network should use the user_priority values. An accompanying
document makes recommendations on the usage of the user_priority document makes recommendations on the usage of the user_priority
values (see [Seaman98] for details). values (see [RFC-MAP] for details).
Under the Integrated Services model, L3 (or higher) entities that Under the Integrated Services model, L3 (or higher) entities that
transmit traffic flows onto a L2 segment should perform per-flow pol- transmit traffic flows onto a L2 segment should perform per-flow pol-
icing to ensure that the flows do not exceed their traffic specifica- icing to ensure that the flows do not exceed their traffic specifica-
tion as specified during admission control. In addition, L3 devices tion as specified during admission control. In addition, L3 devices
may label the frames in such flows with a user_priority value to iden- may label the frames in such flows with a user_priority value to iden-
tify their service class. tify their service class.
For the purpose of this discussion, we will refer to the user_priority For the purpose of this discussion, we will refer to the user_priority
value carried in the extended frame header as the "traffic class" of a value carried in the extended frame header as the "traffic class" of a
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
packet. Under the ISSLL model, the L3 entities, that send traffic and packet. Under the ISSLL model, the L3 entities, that send traffic and
that use the SBM protocol, may select the appropriate traffic class of that use the SBM protocol, may select the appropriate traffic class of
outgoing packets [Seaman98]. This selection may be overridden by DSBM outgoing packets [RFC-MAP]. This selection may be overridden by DSBM
devices, in the following manner. once a sender sends a PATH message, devices, in the following manner. once a sender sends a PATH message,
downstream DSBMs will insert a new traffic class object (TCLASS downstream DSBMs will insert a new traffic class object (TCLASS
object) in the PATH message that travels to the next L3 device (L3 object) in the PATH message that travels to the next L3 device (L3
NHOP for the PATH message). To some extent, the TCLASS object contents NHOP for the PATH message). To some extent, the TCLASS object contents
are treated like the ADSPEC object in the RSVP PATH messages. The L3 are treated like the ADSPEC object in the RSVP PATH messages. The L3
device that receives the PATH message must remove and store the TCLASS device that receives the PATH message must remove and store the TCLASS
object as part of its PATH state for the session. Later, when the same object as part of its PATH state for the session. Later, when the same
L3 device needs to forward a RSVP RESV message towards the original L3 device needs to forward a RSVP RESV message towards the original
sender, it must include the TCLASS object in the RESV message. When sender, it must include the TCLASS object in the RESV message. When
the RESV message arrives at the original sender, the sender must use the RESV message arrives at the original sender, the sender must use
skipping to change at page 17, line 38 skipping to change at page 17, line 38
In summary, use of TCLASS objects requires following additions to the In summary, use of TCLASS objects requires following additions to the
conventional RSVP message processing at DSBMs, SBMs, and DSBM clients: conventional RSVP message processing at DSBMs, SBMs, and DSBM clients:
* When a DSBM receives a PATH message over a managed segment and * When a DSBM receives a PATH message over a managed segment and
the PATH message does not include a TCLASS object, the DSBM MAY the PATH message does not include a TCLASS object, the DSBM MAY
add a TCLASS object to the PATH message before forwarding it. add a TCLASS object to the PATH message before forwarding it.
The DSBM determines the appropriate user_priority value for the The DSBM determines the appropriate user_priority value for the
TCLASS object. A mechanism for selecting the appropriate TCLASS object. A mechanism for selecting the appropriate
user_priority value is described in an accompanying document user_priority value is described in an accompanying document
[Seaman98]. [RFC-MAP].
* When SBM or DSBM receives a PATH message with a TCLASS object * When SBM or DSBM receives a PATH message with a TCLASS object
over a managed segment in a L2 domain and needs to forward it over a managed segment in a L2 domain and needs to forward it
over a managed segment in the same L2 domain, it will store it over a managed segment in the same L2 domain, it will store it
in its path state and typically forward the message without in its path state and typically forward the message without
changing the contents of the TCLASS object. However, if the changing the contents of the TCLASS object. However, if the
DSBM/SBM cannot support the service class represented by the DSBM/SBM cannot support the service class represented by the
user_priority value specified by the TCLASS object in the PATH user_priority value specified by the TCLASS object in the PATH
message, it may change the priority value in the TCLASS to a message, it may change the priority value in the TCLASS to a
semantically "lower" service value to reflect its capability semantically "lower" service value to reflect its capability
and store the changed TCLASS value in its path state. and store the changed TCLASS value in its path state.
[NOTE: An accompanying document defines the int-serv mappings [NOTE: An accompanying document defines the int-serv mappings
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
over IEEE 802 networks [Seaman98] provides a precise definition over IEEE 802 networks [RFC-MAP] provides a precise definition
of user_priority values and describes how the user_priority of user_priority values and describes how the user_priority
values are compared to determine "lower" of the two values or values are compared to determine "lower" of the two values or
the "lowest" among all the user_priority values.] the "lowest" among all the user_priority values.]
* When a DSBM receives a RESV message with a TCLASS object, it * When a DSBM receives a RESV message with a TCLASS object, it
may use the traffic class information (in addition to the usual may use the traffic class information (in addition to the usual
flowspec information in the RSVP message) for its own admission flowspec information in the RSVP message) for its own admission
control for the managed segment. control for the managed segment.
Note that this document does not specify the actual algorithm Note that this document does not specify the actual algorithm
skipping to change at page 19, line 5 skipping to change at page 19, line 5
RESV message it forwards over the interface. RESV message it forwards over the interface.
* When a DSBM client receives a TCLASS object in an incoming RESV * When a DSBM client receives a TCLASS object in an incoming RESV
message over a managed segment and local admission control message over a managed segment and local admission control
succeeds for the session for the outgoing interface over the succeeds for the session for the outgoing interface over the
managed segment, the client must pass the user_priority value managed segment, the client must pass the user_priority value
in the TCLASS object to its local packet classifier. This will in the TCLASS object to its local packet classifier. This will
ensure that the data packets in the admitted RSVP flow that are ensure that the data packets in the admitted RSVP flow that are
subsequently forwarded over the outgoing interface will contain subsequently forwarded over the outgoing interface will contain
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
the appropriate value encoded in their frame header. the appropriate value encoded in their frame header.
* When an L3 device receives a PATH or RESV message over a * When an L3 device receives a PATH or RESV message over a
managed segment in one L2 domain and it needs to forward the managed segment in one L2 domain and it needs to forward the
PATH/RESV message over an interface outside that domain, the L3 PATH/RESV message over an interface outside that domain, the L3
device must remove the TCLASS object (along with LAN_NHOP, device must remove the TCLASS object (along with LAN_NHOP,
RSVP_HOP_L2, and LAN_LOOPBACK objects in the case of the PATH RSVP_HOP_L2, and LAN_LOOPBACK objects in the case of the PATH
message) before forwarding the PATH/RESV message. If the outgo- message) before forwarding the PATH/RESV message. If the outgo-
ing interface is on a separate L2 domain, these objects may be ing interface is on a separate L2 domain, these objects may be
skipping to change at page 20, line 5 skipping to change at page 20, line 5
* A SBM protocol entity residing at a layer 2 device can be a SBM, * A SBM protocol entity residing at a layer 2 device can be a SBM,
a DSBM or none of the above (SBM transparent). A layer 2 device a DSBM or none of the above (SBM transparent). A layer 2 device
will never host a DSBM client. will never host a DSBM client.
5.2. Use Of Reserved IP Multicast Addresses 5.2. Use Of Reserved IP Multicast Addresses
As stated earlier, we require that the DSBM clients forward the RSVP As stated earlier, we require that the DSBM clients forward the RSVP
PATH messages to their DSBMs in a L2 domain before they reach the next PATH messages to their DSBMs in a L2 domain before they reach the next
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
L3 hop in the path. RSVP PATH messages are addressed, according to L3 hop in the path. RSVP PATH messages are addressed, according to
RFC-2205, to their destination address (which can be either an IP uni- RFC-2205, to their destination address (which can be either an IP uni-
cast or multicast address). When a L2 device hosts a DSBM, a simple- cast or multicast address). When a L2 device hosts a DSBM, a simple-
to-implement mechanism must be provided for the device to capture an to-implement mechanism must be provided for the device to capture an
incoming PATH message and hand it over to the local DSBM agent without incoming PATH message and hand it over to the local DSBM agent without
requiring the L2 device to snoop for L3 RSVP messages. requiring the L2 device to snoop for L3 RSVP messages.
In addition, DSBM clients need to know how to address SBM messages to In addition, DSBM clients need to know how to address SBM messages to
the DSBM. For the ease of operation and to allow dynamic DSBM-client the DSBM. For the ease of operation and to allow dynamic DSBM-client
skipping to change at page 21, line 5 skipping to change at page 21, line 5
We define use of two reserved IP multicast addresses. We call these We define use of two reserved IP multicast addresses. We call these
the "AllSBM Address" and the "DSBMLogicalAddress". These are chosen the "AllSBM Address" and the "DSBMLogicalAddress". These are chosen
from the range of local multicast addresses, such that: from the range of local multicast addresses, such that:
* They are not passed through layer 3 devices. * They are not passed through layer 3 devices.
* They are passed transparently through layer 2 devices which are * They are passed transparently through layer 2 devices which are
SBM transparent. SBM transparent.
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
* They are configured in the permanent database of layer 2 devices * They are configured in the permanent database of layer 2 devices
which host SBMs or DSBMs, such that they are directed to the SBM which host SBMs or DSBMs, such that they are directed to the SBM
management entity in these devices. This obviates the need for management entity in these devices. This obviates the need for
these devices to explicitly snoop for SBM related control pack- these devices to explicitly snoop for SBM related control pack-
ets. ets.
* The two reserved addresses are 224.0.0.16 (DSBMLogicalAddress) * The two reserved addresses are 224.0.0.16 (DSBMLogicalAddress)
and 224.0.0.17 (AllSBMAddress). and 224.0.0.17 (AllSBMAddress).
skipping to change at page 22, line 5 skipping to change at page 22, line 5
additional details. additional details.
5.3. Layer 3 to Layer 2 Address Mapping 5.3. Layer 3 to Layer 2 Address Mapping
As stated earlier, DSBMs or DSBM clients residing at a L3 device must As stated earlier, DSBMs or DSBM clients residing at a L3 device must
include a LAN_NHOP_L2 address in the LAN_NHOP information so that L2 include a LAN_NHOP_L2 address in the LAN_NHOP information so that L2
devices along the path of a PATH message do not need to separately devices along the path of a PATH message do not need to separately
determine the mapping between the LAN_NHOP_L3 address in the LAN_NHOP determine the mapping between the LAN_NHOP_L3 address in the LAN_NHOP
object and its corresponding L2 address (for example, using ARP). object and its corresponding L2 address (for example, using ARP).
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
For the purpose of such mapping at L3 devices, we assume a mapping For the purpose of such mapping at L3 devices, we assume a mapping
function called "map_address" that performs the necessary mapping: function called "map_address" that performs the necessary mapping:
L2ADDR object = map_addr(L3Addr) L2ADDR object = map_addr(L3Addr)
We do not specify how the function is implemented; the implementation We do not specify how the function is implemented; the implementation
may simply involve access to the local ARP cache entry or may require may simply involve access to the local ARP cache entry or may require
performing an ARP function. The function returns a L2ADDR object that performing an ARP function. The function returns a L2ADDR object that
need not be interpreted by an L3 device and can be treated as an need not be interpreted by an L3 device and can be treated as an
skipping to change at page 23, line 5 skipping to change at page 23, line 5
We assume that the DSBMs, DSBM clients, and SBMs use only raw IP for We assume that the DSBMs, DSBM clients, and SBMs use only raw IP for
encapsulating RSVP messages that are forwarded onto a L2 domain. encapsulating RSVP messages that are forwarded onto a L2 domain.
Thus, when a SBM protocol entity on a L3 device forwards a RSVP mes- Thus, when a SBM protocol entity on a L3 device forwards a RSVP mes-
sage onto a L2 segment, it will only use RAW IP encapsulation. sage onto a L2 segment, it will only use RAW IP encapsulation.
5.5. The Forwarding Rules 5.5. The Forwarding Rules
The message processing and forwarding rules will be described in the The message processing and forwarding rules will be described in the
context of the sample network illustrated in Figure 2. context of the sample network illustrated in Figure 2.
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
Figure 2 - A sample network or L2 domain consisting of switched and Figure 2 - A sample network or L2 domain consisting of switched and
shared L2 segments shared L2 segments
.......... ..........
. .
+------+ . +------+ seg A +------+ seg C +------+ seg D +------+ +------+ . +------+ seg A +------+ seg C +------+ seg D +------+
| H1 |_______| R1 |_________| S1 |_________| S2 |_________| H2 | | H1 |_______| R1 |_________| S1 |_________| S2 |_________| H2 |
| | . | | | | | | | | | | . | | | | | | | |
+------+ . +------+ +------+ +------+ +------+ +------+ . +------+ +------+ +------+ +------+
skipping to change at page 24, line 5 skipping to change at page 24, line 5
and a shared L2 segment. The sample network contains the following and a shared L2 segment. The sample network contains the following
devices: devices:
Device Type SBM Type Device Type SBM Type
H1, H5 Host (layer 3) SBM Transparent H1, H5 Host (layer 3) SBM Transparent
H2-H4 Host (layer 3) DSBM Client H2-H4 Host (layer 3) DSBM Client
R1 Router (layer 3) SBM R1 Router (layer 3) SBM
R2 Router (layer 3) DSBM for segment F R2 Router (layer 3) DSBM for segment F
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
S1 Switch (layer 2) DSBM for segments A, B S1 Switch (layer 2) DSBM for segments A, B
S2 Switch (layer 2) DSBM for segments C, D, E S2 Switch (layer 2) DSBM for segments C, D, E
S3 Switch (layer 2) SBM S3 Switch (layer 2) SBM
The following paragraphs describe the rules, which each of these dev- The following paragraphs describe the rules, which each of these dev-
ices should use to forward PATH messages (rules apply to PATH_TEAR ices should use to forward PATH messages (rules apply to PATH_TEAR
messages as well). They are described in the context of the general messages as well). They are described in the context of the general
network illustrated above. While the examples do not address every network illustrated above. While the examples do not address every
scenario, they do address most of the interesting scenarios. Excep- scenario, they do address most of the interesting scenarios. Excep-
skipping to change at page 25, line 5 skipping to change at page 25, line 5
* If the device is a layer 3 device, determine whether the inter- * If the device is a layer 3 device, determine whether the inter-
face is on a managed segment managed by a DSBM, based on the face is on a managed segment managed by a DSBM, based on the
presence or absence of I_AM_DSBM messages. If the interface is presence or absence of I_AM_DSBM messages. If the interface is
not on a managed segment, strip out RSVP_HOP_L2, LAN_NHOP, not on a managed segment, strip out RSVP_HOP_L2, LAN_NHOP,
LAN_LOOPBACK, and TCLASS objects (if present), and forward to LAN_LOOPBACK, and TCLASS objects (if present), and forward to
the unicast or multicast destination. the unicast or multicast destination.
(Note that the RSVP Class Numbers for these new objects are (Note that the RSVP Class Numbers for these new objects are
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
chosen so that if an RSVP message includes these objects, the chosen so that if an RSVP message includes these objects, the
nodes that are RSVP-aware, but do not participate in the SBM nodes that are RSVP-aware, but do not participate in the SBM
protocol, will ignore and silently discard such objects.) protocol, will ignore and silently discard such objects.)
* If the device is a layer 2 device or it is a layer 3 device * If the device is a layer 2 device or it is a layer 3 device
*and* the interface is on a managed segment, proceed to rule *and* the interface is on a managed segment, proceed to rule
#3. #3.
3. Forward the PATH message onto the managed segment: 3. Forward the PATH message onto the managed segment:
skipping to change at page 25, line 47 skipping to change at page 25, line 47
- Copy the IP address of the forwarding interface (layer 2 dev- - Copy the IP address of the forwarding interface (layer 2 dev-
ices must also have IP addresses) into the standard RSVP HOP ices must also have IP addresses) into the standard RSVP HOP
object and the L2 address of the forwarding interface into object and the L2 address of the forwarding interface into
the RSVP_HOP_L2 object. the RSVP_HOP_L2 object.
- If the PATH message received does not contain the TCLASS - If the PATH message received does not contain the TCLASS
object, insert a TCLASS object. The user_priority value object, insert a TCLASS object. The user_priority value
inserted in the TCLASS object is based on service mappings inserted in the TCLASS object is based on service mappings
internal to the device that are configured according to the internal to the device that are configured according to the
guidelines listed in [Seaman98]. If the message already guidelines listed in [RFC-MAP]. If the message already
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
contains the TCLASS object, the user_priority value may be contains the TCLASS object, the user_priority value may be
changed based again on the service mappings internal to the changed based again on the service mappings internal to the
device. device.
* If the device is a layer 3 device and hosts a SBM for the seg- * If the device is a layer 3 device and hosts a SBM for the seg-
ment to which the forwarding interface is attached, it *is ment to which the forwarding interface is attached, it *is
required* to retrieve and store the PHOP info. required* to retrieve and store the PHOP info.
If the device is a layer 2 device and hosts a SBM for the seg- If the device is a layer 2 device and hosts a SBM for the seg-
skipping to change at page 27, line 5 skipping to change at page 27, line 5
* If the SBM protocol entity is the DSBM for the segment to which * If the SBM protocol entity is the DSBM for the segment to which
the forwarding interface is attached, it must send the PATH the forwarding interface is attached, it must send the PATH
message to the AllSBMAddress. message to the AllSBMAddress.
* If the SBM protocol entity is a SBM or a DSBM Client on the * If the SBM protocol entity is a SBM or a DSBM Client on the
segment to which the forwarding interface is attached, it must segment to which the forwarding interface is attached, it must
send the PATH message to the DSBMLogicalAddress. send the PATH message to the DSBMLogicalAddress.
5.6.1. Additional notes on forwarding a PATH message onto a 5.6.1. Additional notes on forwarding a PATH message onto a
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
managed segment managed segment
Rule #1 states that normal IEEE 802.1D forwarding rules should be Rule #1 states that normal IEEE 802.1D forwarding rules should be
used to determine the interfaces on which the PATH message should used to determine the interfaces on which the PATH message should
be forwarded. In the case of data packets, standard forwarding be forwarded. In the case of data packets, standard forwarding
rules at a L2 device dictate that the packet should not be for- rules at a L2 device dictate that the packet should not be for-
warded on the interface from which it was received. However, in warded on the interface from which it was received. However, in
the case of a DSBM that receives a PATH message over a managed the case of a DSBM that receives a PATH message over a managed
segment, the following exception applies: segment, the following exception applies:
skipping to change at page 28, line 5 skipping to change at page 28, line 5
LAN_LOOPBACK object addresses this issue. All SBM protocol enti- LAN_LOOPBACK object addresses this issue. All SBM protocol enti-
ties (except DSBMs reflecting a PATH message) overwrite the ties (except DSBMs reflecting a PATH message) overwrite the
LAN_LOOPBACK object in the PATH message with the IP address of LAN_LOOPBACK object in the PATH message with the IP address of
the outgoing interface. DSBMs which are reflecting a PATH mes- the outgoing interface. DSBMs which are reflecting a PATH mes-
sage, leave the LAN_LOOPBACK object unchanged. Thus, SBM proto- sage, leave the LAN_LOOPBACK object unchanged. Thus, SBM proto-
col entities will always be able to recognize a reflected multi- col entities will always be able to recognize a reflected multi-
cast message by the presence of their own address in the cast message by the presence of their own address in the
LAN_LOOPBACK object. These messages should be silently dis- LAN_LOOPBACK object. These messages should be silently dis-
carded. carded.
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
5.7. Applying the Rules -- Unicast Session 5.7. Applying the Rules -- Unicast Session
Let's see how the rules are applied in the general network illus- Let's see how the rules are applied in the general network illus-
trated previously (see Figure 2). trated previously (see Figure 2).
Assume that H1 is sending a PATH for a unicast session for which Assume that H1 is sending a PATH for a unicast session for which
H5 is the receiver. The following PATH message is composed by H1: H5 is the receiver. The following PATH message is composed by H1:
RSVP Contents RSVP Contents
skipping to change at page 29, line 5 skipping to change at page 29, line 5
PHOP IP address of R1 (2.0.0.1) PHOP IP address of R1 (2.0.0.1)
(seed the return path for RESV messages) (seed the return path for RESV messages)
RSVP_HOP_L2 L2 address of R1 RSVP_HOP_L2 L2 address of R1
LAN_NHOP LAN_NHOP_L3 (2.0.0.2) and LAN_NHOP LAN_NHOP_L3 (2.0.0.2) and
LAN_NHOP_L2 address of R2 (L2ADDR) LAN_NHOP_L2 address of R2 (L2ADDR)
(this is the next layer 3 hop) (this is the next layer 3 hop)
LAN_LOOPBACK IP address of R1 (2.0.0.1) LAN_LOOPBACK IP address of R1 (2.0.0.1)
IP Header IP Header
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
Source address IP address of H1 Source address IP address of H1
Destn address DSBMLogical IP address (224.0.0.16) Destn address DSBMLogical IP address (224.0.0.16)
MAC Header MAC Header
Destn address DSBMLogical MAC address Destn address DSBMLogical MAC address
* R1 does a routing lookup on the RSVP session address, to * R1 does a routing lookup on the RSVP session address, to
determine the IP address of the next layer 3 hop, R2. determine the IP address of the next layer 3 hop, R2.
* It determines that R2 is accessible via seg A and that seg A * It determines that R2 is accessible via seg A and that seg A
is managed by a DSBM, S1. is managed by a DSBM, S1.
* Therefore, it concludes that it is sending onto a managed * Therefore, it concludes that it is sending onto a managed
segment, and composes LAN_NHOP objects to carry the layer 3 segment, and composes LAN_NHOP objects to carry the layer 3
and layer 2 next hop addresses. To compose the LAN_NHOP and layer 2 next hop addresses. To compose the LAN_NHOP
L2ADDR object, it invokes the L3L2 address mapping function L2ADDR object, it invokes the L3 to L2 address mapping function
("map_address") to find out the MAC address for the next hop ("map_address") to find out the MAC address for the next hop
L3 device, and then inserts a LAN_NHOP_L2ADDR object (that L3 device, and then inserts a LAN_NHOP_L2ADDR object (that
carries the MAC address) in the message. carries the MAC address) in the message.
* Since R1 is not the DSBM for seg A, it sends the PATH message * Since R1 is not the DSBM for seg A, it sends the PATH message
to the DSBMLogicalAddress. to the DSBMLogicalAddress.
Upon receipt of the PATH message, S1 composes and forwards a PATH Upon receipt of the PATH message, S1 composes and forwards a PATH
message as follows: message as follows:
skipping to change at page 30, line 5 skipping to change at page 30, line 5
RSVP_HOP_L2 L2 address of S1 RSVP_HOP_L2 L2 address of S1
LAN_NHOP LAN_NHOP_L3 (IP) and LAN_NHOP_L2 LAN_NHOP LAN_NHOP_L3 (IP) and LAN_NHOP_L2
address of R2 address of R2
(layer 2 devices do not modify the LAN_NHOP) (layer 2 devices do not modify the LAN_NHOP)
LAN_LOOPBACK IP addr of S1 LAN_LOOPBACK IP addr of S1
IP Header IP Header
Source address IP address of H1 Source address IP address of H1
Destn address AllSBMIPaddr (224.0.0.17, since S1 is the Destn address AllSBMIPaddr (224.0.0.17, since S1 is the
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
DSBM for seg B). DSBM for seg B).
MAC Header MAC Header
Destn address All SBM MAC address (since S1 is the DSBM for Destn address All SBM MAC address (since S1 is the DSBM for
seg B). seg B).
* S1 looks at the LAN_NHOP address information to determine the * S1 looks at the LAN_NHOP address information to determine the
L2 address towards which it should forward the PATH message. L2 address towards which it should forward the PATH message.
skipping to change at page 31, line 5 skipping to change at page 31, line 5
LAN_LOOPBACK IP address of S3 LAN_LOOPBACK IP address of S3
IP Header IP Header
Source address IP address of H1 Source address IP address of H1
Destn address DSBMLogical IP addr (since S3 is Destn address DSBMLogical IP addr (since S3 is
not the DSBM for seg F) not the DSBM for seg F)
MAC Header MAC Header
Destn address DSBMLogical MAC address Destn address DSBMLogical MAC address
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
* S3 looks at the LAN_NHOP address information to determine the * S3 looks at the LAN_NHOP address information to determine the
L2 address towards which it should forward the PATH message. L2 address towards which it should forward the PATH message.
* From the bridge forwarding tables, it determines that the L2 * From the bridge forwarding tables, it determines that the L2
address is reachable via segment F. address is reachable via segment F.
* It has discovered that R2 is the DSBM for segment F. It * It has discovered that R2 is the DSBM for segment F. It
therefore sends the PATH message to the DSBMLogicalAddress. therefore sends the PATH message to the DSBMLogicalAddress.
skipping to change at page 32, line 5 skipping to change at page 32, line 5
MAC Header MAC Header
Destn address L2 addr corresponding to H5, the next Destn address L2 addr corresponding to H5, the next
layer 3 hop layer 3 hop
* R2 does a routing lookup on the RSVP session address, to * R2 does a routing lookup on the RSVP session address, to
determine the IP address of the next layer 3 hop, H5. determine the IP address of the next layer 3 hop, H5.
* It determines that H5 is accessible via a segment for which * It determines that H5 is accessible via a segment for which
there is no DSBM (not a managed segment). there is no DSBM (not a managed segment).
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
* Therefore, it removes the LAN_NHOP and RSVP_HOP_L2 objects * Therefore, it removes the LAN_NHOP and RSVP_HOP_L2 objects
and places the RSVP session address in the destination and places the RSVP session address in the destination
address of the IP header. It places the L2 address of the address of the IP header. It places the L2 address of the
next layer 3 hop, into the destination address of the MAC next layer 3 hop, into the destination address of the MAC
header and forwards the PATH message to H5. header and forwards the PATH message to H5.
5.8. Applying the Rules - Multicast Session 5.8. Applying the Rules - Multicast Session
The rules described above also apply to multicast (m/c) sessions. The rules described above also apply to multicast (m/c) sessions.
skipping to change at page 33, line 5 skipping to change at page 33, line 5
PHOP IP addr of R2 (seed the return path for PHOP IP addr of R2 (seed the return path for
RESV messages) RESV messages)
RSVP_HOP_L2 L2 addr of R2 RSVP_HOP_L2 L2 addr of R2
LAN_NHOP m/c session address and corresponding L2 address LAN_NHOP m/c session address and corresponding L2 address
LAN_LOOPBACK IP addr of S3 (DSBMs reflecting a PATH LAN_LOOPBACK IP addr of S3 (DSBMs reflecting a PATH
message don't modify this object) message don't modify this object)
IP Header IP Header
Source address IP address of H1 Source address IP address of H1
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
Destn address AllSBMIP address (since R2 is the DSBM for seg F) Destn address AllSBMIP address (since R2 is the DSBM for seg F)
MAC Header MAC Header
Destn address AllSBMMAC address (since R2 is the Destn address AllSBMMAC address (since R2 is the
DSBM for seg F) DSBM for seg F)
Since H3 is monitoring the All SBM Address, it will receive the Since H3 is monitoring the All SBM Address, it will receive the
PATH message reflected by R2. Note that R2 violated the standard PATH message reflected by R2. Note that R2 violated the standard
forwarding rules here by sending an incoming message back onto the forwarding rules here by sending an incoming message back onto the
skipping to change at page 34, line 5 skipping to change at page 34, line 5
* R2 determines that there is an m/c receiver accessible via a * R2 determines that there is an m/c receiver accessible via a
segment for which there is no DSBM. Therefore, it removes the segment for which there is no DSBM. Therefore, it removes the
LAN_NHOP and RSVP_HOP_L2 objects and places the RSVP session LAN_NHOP and RSVP_HOP_L2 objects and places the RSVP session
address in the destination address of the IP header. It address in the destination address of the IP header. It
places the corresponding L2 address into the destination places the corresponding L2 address into the destination
address of the MAC header and multicasts the message towards address of the MAC header and multicasts the message towards
H5. H5.
5.9. Merging Traffic Class objects 5.9. Merging Traffic Class objects
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
When a DSBM client receives TCLASS objects from different senders When a DSBM client receives TCLASS objects from different senders
(different PATH messages) in the same RSVP session and needs to (different PATH messages) in the same RSVP session and needs to
combine them for sending back a single RESV message (as in a combine them for sending back a single RESV message (as in a
wild-card style reservation), the DSBM client must choose an wild-card style reservation), the DSBM client must choose an
appropriate value that corresponds to the desired-delay traffic appropriate value that corresponds to the desired-delay traffic
class. An accompanying document discusses the guidelines for class. An accompanying document discusses the guidelines for
traffic class selection based on desired service and the TSpec traffic class selection based on desired service and the TSpec
information [Seaman98]. information [RFC-MAP].
In addition, when a SBM or DSBM needs to merge RESVs from dif- In addition, when a SBM or DSBM needs to merge RESVs from dif-
ferent next hops at a merge point, it must decide how to handle ferent next hops at a merge point, it must decide how to handle
the TCLASS values in the incoming RESVs if they do not match. Con- the TCLASS values in the incoming RESVs if they do not match. Con-
sider the case when a reservation is in place for a flow at a DSBM sider the case when a reservation is in place for a flow at a DSBM
(or SBM) with a successful admission control done for the TCLASS (or SBM) with a successful admission control done for the TCLASS
requested in the first RESV for the flow. If another RESV (not the requested in the first RESV for the flow. If another RESV (not the
refresh of the previously admitted RESV) for the same flow arrives refresh of the previously admitted RESV) for the same flow arrives
at the DSBM, the DSBM must first check the TCLASS value in the new at the DSBM, the DSBM must first check the TCLASS value in the new
RESV against the TCLASS value in the already installed RESV. If RESV against the TCLASS value in the already installed RESV. If
skipping to change at page 35, line 5 skipping to change at page 35, line 5
ticipate in routing of PATH or RESV messages, and they do not par- ticipate in routing of PATH or RESV messages, and they do not par-
ticipate in admission control. They are entirely transparent with ticipate in admission control. They are entirely transparent with
respect to SBM operation. respect to SBM operation.
According to the definitions provided, physical segments intercon- According to the definitions provided, physical segments intercon-
nected by SBM transparent devices are considered a single managed nected by SBM transparent devices are considered a single managed
segment. Therefore, DSBMs must perform admission control on such segment. Therefore, DSBMs must perform admission control on such
managed segments, with limited knowledge of the segment's topol- managed segments, with limited knowledge of the segment's topol-
ogy. In this case, the network administrator should configure the ogy. In this case, the network administrator should configure the
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
DSBM for each managed segment, with some reasonable approximation DSBM for each managed segment, with some reasonable approximation
of the segment's capacity. A conservative policy would configure of the segment's capacity. A conservative policy would configure
the DSBM for the lowest capacity route through the managed seg- the DSBM for the lowest capacity route through the managed seg-
ment. A liberal policy would configure the DSBM for the highest ment. A liberal policy would configure the DSBM for the highest
capacity route through the managed segment. A network administra- capacity route through the managed segment. A network administra-
tor will likely choose some value between the two, based on the tor will likely choose some value between the two, based on the
level of guarantee required and some knowledge of likely traffic level of guarantee required and some knowledge of likely traffic
patterns. patterns.
skipping to change at page 36, line 5 skipping to change at page 36, line 5
Note that, SBM protocol entities which are not DSBMs, are not Note that, SBM protocol entities which are not DSBMs, are not
required to overwrite the PHOP in incident PATH messages with required to overwrite the PHOP in incident PATH messages with
their own address. This is because it is not necessary for RESV their own address. This is because it is not necessary for RESV
messages to be routed through these devices. RESV messages are messages to be routed through these devices. RESV messages are
only required to be routed through the correct sequence of DSBMs. only required to be routed through the correct sequence of DSBMs.
SBMs may not process RESV messages that do pass through them, SBMs may not process RESV messages that do pass through them,
other than to forward them towards their destination address, other than to forward them towards their destination address,
using standard forwarding rules. using standard forwarding rules.
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
SBM protocol entities which are not DSBMs are required to SBM protocol entities which are not DSBMs are required to
overwrite the address in the LAN_LOOPBACK object with their own overwrite the address in the LAN_LOOPBACK object with their own
address, in order to avoid looping multicast messages. However, no address, in order to avoid looping multicast messages. However, no
state need be stored. state need be stored.
6. Inter-Operability Considerations 6. Inter-Operability Considerations
There are a few interesting inter-operability issues related to There are a few interesting inter-operability issues related to
the deployment of a DSBM-based admission control method in an the deployment of a DSBM-based admission control method in an
skipping to change at page 36, line 31 skipping to change at page 36, line 31
6.1. An L2 domain with no RSVP capability. 6.1. An L2 domain with no RSVP capability.
It is possible to envisage L2 domains that do not use RSVP signal- It is possible to envisage L2 domains that do not use RSVP signal-
ing for requesting resource reservations, but, instead, use some ing for requesting resource reservations, but, instead, use some
other (e.g., SNMP or static configuration) mechanism to reserve other (e.g., SNMP or static configuration) mechanism to reserve
bandwidth at a particular network device such as a router. In that bandwidth at a particular network device such as a router. In that
case, the question is how does a DSBM-based admission control case, the question is how does a DSBM-based admission control
method work and interoperate with the non-RSVP mechanism. The method work and interoperate with the non-RSVP mechanism. The
SBM-based method does not attempt to provide an admission control SBM-based method does not attempt to provide an admission control
solution for such an environment. The SBM-based approach is part solution for such an environment. The SBM-based approach is part
of an end2end signaling approach to establish resource reserva- of an end to end signaling approach to establish resource reserva-
tions and does not attempt to provide a solution for SNMP-based tions and does not attempt to provide a solution for SNMP-based
configuration scenario. configuration scenario.
As stated earlier, the SBM-based approach can, however, co-exist As stated earlier, the SBM-based approach can, however, co-exist
with any other, non-RSVP bandwidth allocation mechanism as long as with any other, non-RSVP bandwidth allocation mechanism as long as
resources being reserved are either partitioned statically between resources being reserved are either partitioned statically between
the different mechanisms or are resolved dynamically through a the different mechanisms or are resolved dynamically through a
common bandwidth allocator so that there is no over-commitment of common bandwidth allocator so that there is no over-commitment of
the same resource. the same resource.
6.2. An L2 domain with SBM-transparent L2 Devices. 6.2. An L2 domain with SBM-transparent L2 Devices.
This scenario has been addressed earlier in the document. The This scenario has been addressed earlier in the document. The
SBM-based method is designed to operate in such an environment. SBM-based method is designed to operate in such an environment.
When SBM-transparent L2 devices interconnect SBM-aware devices, When SBM-transparent L2 devices interconnect SBM-aware devices,
the resulting managed segment is a combination of one or more phy- the resulting managed segment is a combination of one or more phy-
sical segments and the DSBM for the managed segment may not be as sical segments and the DSBM for the managed segment may not be as
efficient in allocating resources as it would if all L2 devices efficient in allocating resources as it would if all L2 devices
were SBM-aware. were SBM-aware.
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
6.3. An L2 domain on which some RSVP-based senders are not DSBM 6.3. An L2 domain on which some RSVP-based senders are not DSBM
clients. clients.
All senders that are sourcing RSVP-based traffic flows onto a All senders that are sourcing RSVP-based traffic flows onto a
managed segment MUST be SBM-aware and participate in the SBM pro- managed segment MUST be SBM-aware and participate in the SBM pro-
tocol. Use of the standard, non-SBM version of RSVP may result in tocol. Use of the standard, non-SBM version of RSVP may result in
over-allocation of resources, as such use bypasses the resource over-allocation of resources, as such use bypasses the resource
management function of the DSBM. All other senders (i.e., senders management function of the DSBM. All other senders (i.e., senders
that are not sending streams subject to RSVP admission control) that are not sending streams subject to RSVP admission control)
skipping to change at page 37, line 49 skipping to change at page 37, line 49
RAW_IP RAW_IP
This document stipulates that DSBMs, DSBM clients, and SBMs use This document stipulates that DSBMs, DSBM clients, and SBMs use
only raw IP for encapsulating RSVP messages that are forwarded only raw IP for encapsulating RSVP messages that are forwarded
onto a L2 domain. RFC-2205 (the RSVP Proposed Standard) includes onto a L2 domain. RFC-2205 (the RSVP Proposed Standard) includes
support for both raw IP and UDP encapsulation. Thus, a RSVP node support for both raw IP and UDP encapsulation. Thus, a RSVP node
using only the UDP encapsulation will not be able to interoperate using only the UDP encapsulation will not be able to interoperate
with the DSBM unless DSBM accepts and supports UDP encapsulated with the DSBM unless DSBM accepts and supports UDP encapsulated
RSVP messages. RSVP messages.
7. Guidelines for Implementors 7. Guidelines for Implementers
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
In the following, we provide guidelines for implementors on dif- In the following, we provide guidelines for implementers on dif-
ferent aspects of the implementation of the SBM-based admission ferent aspects of the implementation of the SBM-based admission
control procedure including suggestions for DSBM initialization, control procedure including suggestions for DSBM initialization,
etc. etc.
7.1. DSBM Initialization 7.1. DSBM Initialization
As stated earlier, DSBM initialization includes configuration of As stated earlier, DSBM initialization includes configuration of
maximum bandwidth that can be reserved on a managed segment under maximum bandwidth that can be reserved on a managed segment under
its control. We suggest the following guideline. its control. We suggest the following guideline.
In the case of a managed segment consisting of L2 devices inter- In the case of a managed segment consisting of L2 devices inter-
connected by a single shared segment, DSBM entities on such dev- connected by a single shared segment, DSBM entities on such dev-
ices should assume the bandwidth of the interface as the total ices should assume the bandwidth of the interface as the total
link bandwidth. In the case of a DSBM located in a L2 switch, it link bandwidth. In the case of a DSBM located in a L2 switch, it
might additionally need to be configured with an estimate of the might additionally need to be configured with an estimate of the
device's switching capacity if that is less than the link device's switching capacity if that is less than the link
bandwidth, and possibly with some estimate of the buffering bandwidth, and possibly with some estimate of the buffering
resources of the switch (see [Ghanwani98] for the architectural resources of the switch (see [RFC-FRAME] for the architectural
model assumed for L2 switches). Given the total link bandwidth, model assumed for L2 switches). Given the total link bandwidth,
the DSBM may be further configured to limit the maximum amount of the DSBM may be further configured to limit the maximum amount of
bandwidth for RSVP-enabled flows to ensure spare capacity for bandwidth for RSVP-enabled flows to ensure spare capacity for
best-effort traffic. best-effort traffic.
7.2. Operation of DSBMs in Different L2 Topologies 7.2. Operation of DSBMs in Different L2 Topologies
Depending on a L2 topology, a DSBM may be called upon to manage Depending on a L2 topology, a DSBM may be called upon to manage
resources for one or more segments and the implementors must bear resources for one or more segments and the implementers must bear
in mind efficiency implications of the use of DSBM in different L2 in mind efficiency implications of the use of DSBM in different L2
topologies. Trivial L2 topologies consist of a single "physical topologies. Trivial L2 topologies consist of a single "physical
segment". In this case, the 'managed segment' is equivalent to a segment". In this case, the 'managed segment' is equivalent to a
single segment. Complex L2 topologies may consist of a number of single segment. Complex L2 topologies may consist of a number of
'physical segments', separated by SBM-transparent L2 switches. 'physical segments', separated by SBM-transparent L2 switches.
Admission control on such an L2 extended segment can be performed Admission control on such an L2 extended segment can be performed
from a single pool of resources, similar to a single shared seg- from a single pool of resources, similar to a single shared seg-
ment, from the point of view of a single DSBM. ment, from the point of view of a single DSBM.
This configuration compromises the efficiency with which the DSBM This configuration compromises the efficiency with which the DSBM
can allocate resources. This is because the single DSBM is can allocate resources. This is because the single DSBM is
required to make admission control decisions for all reservation required to make admission control decisions for all reservation
requests within the L2 topology, with no knowledge of the actual requests within the L2 topology, with no knowledge of the actual
physical segments affected by the reservation. physical segments affected by the reservation.
We can realize improvements in the efficiency of resource alloca- We can realize improvements in the efficiency of resource alloca-
tion by subdividing the complex segment into a number of managed tion by subdividing the complex segment into a number of managed
segments, each managed by their own DSBM. In this case, each DSBM segments, each managed by their own DSBM. In this case, each DSBM
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
manages a managed segment having a relatively simple topology. manages a managed segment having a relatively simple topology.
Since managed segments are simpler, the DSBM can be configured Since managed segments are simpler, the DSBM can be configured
with a more accurate estimate of the resources available for all with a more accurate estimate of the resources available for all
reservations in the managed segment. In the ultimate configura- reservations in the managed segment. In the ultimate configura-
tion, each physical segment is a managed segment and is managed by tion, each physical segment is a managed segment and is managed by
its own DSBM. We make no assumption about the number of managed its own DSBM. We make no assumption about the number of managed
segments but state, simply, that in complex L2 topologies, the segments but state, simply, that in complex L2 topologies, the
efficiency of resource allocation improves as the granularity of efficiency of resource allocation improves as the granularity of
managed segments increases. managed segments increases.
8. Security Considerations 8. Security Considerations
The message formatting and usage rules described in this note The message formatting and usage rules described in this note
raise some security issues, but they are no different than the raise security issues, identical to those raised by the use of
ones raised by the use of RSVP and Integrated Services; the need RSVP and Integrated Services. It is necessary to control and
to control and authenticate access to enhanced qualities of ser- authenticate access to enhanced qualities of service enabled by
vice. This requirement is discussed further in [RFC-2205], [RFC- the technology described in this RFC. This requirement is
2211], and [RFC-2212]. [Baker97] describes the mechanism used to discussed further in [RFC-2205], [RFC-2211], and [RFC-2212].
protect the integrity of RSVP messages carrying the information
described here. A SBM implementation should satisfy these require-
ments and provide the suggested mechanisms just as though it were
a conventional RSVP implementation and also protect the addi-
tional, SBM-specific objects in a message.
In addition, it is also necessary to authenticate DSBM candidates [RFC-RSVPMD5] describes the mechanism used to protect the
integrity of RSVP messages carrying the information described
here. A SBM implementation should satisfy the requirements of
that RFC and provide
the suggested mechanisms just as though it were a
conventional RSVP implementation. It should further use the
same mechanisms to
protect the additional, SBM-specific objects in a message.
Finally, it is also necessary to authenticate DSBM candidates
during the election process, and a mechanism based on a shared during the election process, and a mechanism based on a shared
secret among the DSBM candidates may be used. The mechanism secret among the DSBM candidates may be used. The mechanism
defined in [Baker97] should be used. defined in [RFC-RSVPMD5] should be used.
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
9. References 9. References
[RFC-2205] R. Braden, L. Zhang, S. Berson, S. Herzog, S. Jamin, [RFC-2205] R. Braden, L. Zhang, S. Berson, S. Herzog, S. Jamin,
"Resource ReSerVation Protocol (RSVP) -- Version 1 Functional "Resource ReSerVation Protocol (RSVP) -- Version 1 Functional
Specification ", RFC-2205, September 1997. Specification ", RFC-2205, September 1997.
[Baker97] F. Baker., "RSVP Cryptographic Authentication", draft- [RFC-RSVPMD5] F. Baker., "RSVP Cryptographic Authentication", draft-
ietf-rsvp-md5-05.txt, August 1997. ietf-rsvp-md5-05.txt, August 1997. [XXX- is this a RFC yet??]
[RFC-2206] F. Baker, J. Krawczyk, "RSVP Management Information [RFC-2206] F. Baker, J. Krawczyk, "RSVP Management Information
Base", RFC 2206, September 1997. Base", RFC 2206, September 1997.
[RFC-2211] J. Wroclawski, "Specification of the Controlled-Load [RFC-2211] J. Wroclawski, "Specification of the Controlled-Load
Network Element Service", RFC-2211, September 1997. Network Element Service", RFC-2211, September 1997.
[RFC-2212] S. Shenker, C. Partridge, R. Guerin, "Specification of [RFC-2212] S. Shenker, C. Partridge, R. Guerin, "Specification of
Guaranteed Quality of Service", RFC-2212, September 1997. Guaranteed Quality of Service", RFC-2212, September 1997.
[RFC-2215] S. Shenker, J. Wroclawski, "General Characterization [RFC-2215] S. Shenker, J. Wroclawski, "General Characterization
Parameters for Integrated Service Network Elements", RFC-2215, Parameters for Integrated Service Network Elements", RFC-2215,
September 1997. September 1997.
[RFC-2210] J. Wroclawski, "The Use of RSVP with IETF Integrated [RFC-2210] J. Wroclawski, "The Use of RSVP with IETF Integrated
Services", RFC 2210, September 1997. Services", RFC 2210, September 1997.
[RFC-2213] F. Baker, J. Krawczyk, "Integrated Services Management [RFC-2213] F. Baker, J. Krawczyk, "Integrated Services Management
Information Base", RFC 2213, September 1997. Information Base", RFC 2213, September 1997.
[Ghanwani98] A. Ghanwani, W. Pace, V. Srinivasan, A.Smith, [RFC-FRAME] A. Ghanwani, W. Pace, V. Srinivasan, A.Smith,
M.Seaman "A Framework for Providing Integrated Services Over M.Seaman "A Framework for Providing Integrated Services Over
Shared and Switched LAN Technologies", Internet Draft <draft- Shared and Switched LAN Technologies", RFC-XXX, June, 1999.
ietf-issll-is802-framework-05.txt>, November 1998.
[Seaman98] M. Seaman, A. Smith, E. Crawley, "Integrated Service [RFC-MAP] M. Seaman, A. Smith, E. Crawley, "Integrated Service
Mappings on IEEE 802 Networks", Internet Draft <draft-ietf-issll- Mappings on IEEE 802 Networks", RFC-XXX, June 1999.
is802-svc-mapping-04.txt>, November 1998.
[IEEE802Q] "IEEE Standards for Local and Metropolitan Area Net- [IEEE802Q] "IEEE Standards for Local and Metropolitan Area Net-
works: Virtual Bridged Local Area Networks", Draft Standard works: Virtual Bridged Local Area Networks", Draft Standard
P802.1Q/D9, February 20, 1998. P802.1Q/D9, February 20, 1998.
[IEEEP8021p] "Information technology - Telecommunications and [IEEEP8021p] "Information technology - Telecommunications and
information exchange between systems - Local and metropolitan area information exchange between systems - Local and metropolitan area
networks - Common specifications - Part 3: Media Access Control networks - Common specifications - Part 3: Media Access Control
(MAC) Bridges: Revision (Incorporating IEEE P802.1p: Traffic (MAC) Bridges: Revision (Incorporating IEEE P802.1p: Traffic
Class Expediting and Dynamic Multicast Filtering)", ISO/IEC Final Class Expediting and Dynamic Multicast Filtering)", ISO/IEC Final
CD 15802-3 IEEE P802.1D/D15, November 24, 1997. CD 15802-3 IEEE P802.1D/D15, November 24, 1997.
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
[IEEE8021D] "MAC Bridges", ISO/IEC 10038, ANSI/IEEE Std 802.1D- [IEEE8021D] "MAC Bridges", ISO/IEC 10038, ANSI/IEEE Std 802.1D-
1993. 1993.
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
Appendix A Appendix A
DSBM Election Algorithm DSBM Election Algorithm
A.1. Introduction A.1. Introduction
To simplify the rest of this discussion, we will assume that there To simplify the rest of this discussion, we will assume that there
is a single DSBM for the entire L2 domain (i.e., assume a shared is a single DSBM for the entire L2 domain (i.e., assume a shared
L2 segment for the entire L2 domain). Later, we will discuss how a L2 segment for the entire L2 domain). Later, we will discuss how a
DSBM is elected for a half-duplex or full-duplex switched segment. DSBM is elected for a half-duplex or full-duplex switched segment.
skipping to change at page 42, line 31 skipping to change at page 42, line 31
the DSBM is elected and is operational, other SBMs remain passive the DSBM is elected and is operational, other SBMs remain passive
in the background to step in to elect a new DSBM when necessary. in the background to step in to elect a new DSBM when necessary.
The protocol for electing and discovering DSBM is called the "DSBM The protocol for electing and discovering DSBM is called the "DSBM
election protocol" and is described in the rest of this Appendix. election protocol" and is described in the rest of this Appendix.
A.1.1. How a DSBM Client Detects a Managed Segment A.1.1. How a DSBM Client Detects a Managed Segment
Once elected, a DSBM periodically multicasts an I_AM_DSBM message Once elected, a DSBM periodically multicasts an I_AM_DSBM message
on the AllSBMAddress to indicate its presence. The message is sent on the AllSBMAddress to indicate its presence. The message is sent
every period (e.g., every 5 seconds) according to the every period (e.g., every 5 seconds) according to the
DSBMRefreshInterval timer value (a configuration parameter). RefreshInterval timer value (a configuration parameter).
Absence of such a message over a certain time interval (called Absence of such a message over a certain time interval (called
"DSBMDeadInterval"; another configuration parameter typically set "DSBMDeadInterval"; another configuration parameter typically set
to a multiple of RefreshInterval) indicates that the DSBM has to a multiple of RefreshInterval) indicates that the DSBM has
failed or terminated and triggers another round of the DSBM elec- failed or terminated and triggers another round of the DSBM elec-
tion. The DSBM clients always listen for periodic DSBM advertise- tion. The DSBM clients always listen for periodic DSBM advertise-
ments. The advertisement includes the unicast IP address of the ments. The advertisement includes the unicast IP address of the
DSBM (DSBMAddress) and DSBM clients send their PATH/RESV (or DSBM (DSBMAddress) and DSBM clients send their PATH/RESV (or
other) messages to the DSBM. When a DSBM client detects the other) messages to the DSBM. When a DSBM client detects the
failure of a DSBM, it waits for a subsequent I_AM_DSBM advertise- failure of a DSBM, it waits for a subsequent I_AM_DSBM advertise-
ment before resuming any communication with the DSBM. During the ment before resuming any communication with the DSBM. During the
period when a DSBM is not present, a DSBM client may forward out- period when a DSBM is not present, a DSBM client may forward out-
going PATH messages using the standard RSVP forwarding rules. going PATH messages using the standard RSVP forwarding rules.
The exact message formats and addresses used for communication The exact message formats and addresses used for communication
with (and among) SBM(s) are described in Appendix B. with (and among) SBM(s) are described in Appendix B.
A.2. Overview of the DSBM Election Procedure A.2. Overview of the DSBM Election Procedure
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
When a SBM first starts up, it listens for incoming DSBM adver- When a SBM first starts up, it listens for incoming DSBM adver-
tisements for some period to check whether a DSBM already exists tisements for some period to check whether a DSBM already exists
in its L2 domain. If one already exists (and no new election is in in its L2 domain. If one already exists (and no new election is in
progress), the new SBM stays quiet in the background until an progress), the new SBM stays quiet in the background until an
election of DSBM is necessary. All messages related to the DSBM election of DSBM is necessary. All messages related to the DSBM
election and DSBM advertisements are always sent to the AllSBMAd- election and DSBM advertisements are always sent to the AllSBMAd-
dress. dress.
If no DSBM exists, the SBM initiates the election of a DSBM by If no DSBM exists, the SBM initiates the election of a DSBM by
skipping to change at page 43, line 29 skipping to change at page 43, line 29
SBM candidate exists, the SBM priority determines who gets to be SBM candidate exists, the SBM priority determines who gets to be
the DSBM based on the relative priority of candidates. If there is the DSBM based on the relative priority of candidates. If there is
a tie based on the priority value, the tie is broken using the IP a tie based on the priority value, the tie is broken using the IP
addresses of tied candidates (one with the higher IP address in addresses of tied candidates (one with the higher IP address in
the lexicographic order wins). The details of the election proto- the lexicographic order wins). The details of the election proto-
col start in Section A.4. col start in Section A.4.
A.2.1 Summary of the Election Algorithm A.2.1 Summary of the Election Algorithm
For the purpose of the algorithm, a SBM is in one of the four For the purpose of the algorithm, a SBM is in one of the four
states (Idle, DetectDSBM, ElectDSBM, I_AM_DSBM). states (Idle, DetectDSBM, ElectDSBM, IAMDSBM).
A SBM (call it X) starts up in the DetectDSBM state and waits for A SBM (call it X) starts up in the DetectDSBM state and waits for
a ListenInterval for incoming I_AM_DSBM (DSBM advertisement) or a ListenInterval for incoming I_AM_DSBM (DSBM advertisement) or
DSBM_WILLING messages. If an I_AM_DSBM advertisement is received DSBM_WILLING messages. If an I_AM_DSBM advertisement is received
during this state, the SBM notes the current DSBM (its IP address during this state, the SBM notes the current DSBM (its IP address
and priority) and enters the Idle state. If a DSBM_WILLING message and priority) and enters the Idle state. If a DSBM_WILLING message
is received from another SBM (call it Y) during this state, then X is received from another SBM (call it Y) during this state, then X
enters the ElectDSBM state. Before entering the new state, X first enters the ElectDSBM state. Before entering the new state, X first
checks to see whether it itself is a better candidate than Y and, checks to see whether it itself is a better candidate than Y and,
if so, sends out a DSBM_WILLING message and then enters the if so, sends out a DSBM_WILLING message and then enters the
ElectDSBM state. ElectDSBM state.
When a SBM (call it X) enters the ElectDSBM state, it sets a timer When a SBM (call it X) enters the ElectDSBM state, it sets a timer
(called ElectionIntervalTimer that is typically set to a value at (called ElectionIntervalTimer, and typically set to a value at
least equal to the DeadIntervalTimer value) to wait for the elec- least equal to the DSBMDeadInterval value) to wait for the elec-
tion to finish and to discover who is the best candidate. In this tion to finish and to discover who is the best candidate. In this
state, X keeps track of the best (or better) candidate seen so far state, X keeps track of the best (or better) candidate seen so far
(including itself). Whenever it receives another DSBM_WILLING mes- (including itself). Whenever it receives another DSBM_WILLING mes-
sage, it updates its notion of the best (or better) candidate sage, it updates its notion of the best (or better) candidate
based on the priority (and tie-breaking) criterion. During the based on the priority (and tie-breaking) criterion. During the
ElectionInterval, X sends out a DSBM_WILLING message every ElectionInterval, X sends out a DSBM_WILLING message every
RefreshInterval to (re)assert its candidacy. RefreshInterval to (re)assert its candidacy.
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
At the end of the ElectionInterval, X checks whether it is the At the end of the ElectionInterval, X checks whether it is the
best candidate so far. If so, it declares itself to be the DSBM best candidate so far. If so, it declares itself to be the DSBM
(by sending out the I_AM_DSBM advertisement) and enters the (by sending out the I_AM_DSBM advertisement) and enters the
I_AM_DSBM state; otherwise, it decides to wait for the best candi- IAMDSBM state; otherwise, it decides to wait for the best candi-
date to declare itself the winner. To wait, X re-initializes its date to declare itself the winner. To wait, X re-initializes its
ElectDSBM state and continues to wait for another round of elec- ElectDSBM state and continues to wait for another round of elec-
tion (each round lasts for an ElectionTimerInterval duration). tion (each round lasts for an ElectionTimerInterval duration).
A SBM is in Idle state when no election is in progress and the A SBM is in Idle state when no election is in progress and the
DSBM is already elected (and happens to be someone else). In this DSBM is already elected (and happens to be someone else). In this
state, it listens for incoming I_AM_DSBM advertisements and uses state, it listens for incoming I_AM_DSBM advertisements and uses
a DSBMDeadInterval timer to detect the failure of DSBM. Every time a DSBMDeadIntervalTimer to detect the failure of DSBM. Every time
the advertisement is received, the timer is restarted. If the the advertisement is received, the timer is restarted. If the
timer fires, the SBM goes into the DetectDSBM state to prepare to timer fires, the SBM goes into the DetectDSBM state to prepare to
elect the new DSBM. If a SBM receives a DSBM_WILLING message from elect the new DSBM. If a SBM receives a DSBM_WILLING message from
the current DSBM in this state, the SBM enters the ElectDSBM state the current DSBM in this state, the SBM enters the ElectDSBM state
after sending out a DSBM_WILLING message (to announce its own after sending out a DSBM_WILLING message (to announce its own
candidacy). candidacy).
In the I_AM_DSBM state, the DSBM sends out I_AM_DSBM advertise- In the IAMDSBM state, the DSBM sends out I_AM_DSBM advertise-
ments every refresh interval. If the DSBM wishes to shut down ments every refresh interval. If the DSBM wishes to shut down
(gracefully terminate), it sends out a DSBM_WILLING message (with (gracefully terminate), it sends out a DSBM_WILLING message (with
SBM priority value set to zero) to initiate the election pro- SBM priority value set to zero) to initiate the election pro-
cedure. The priority value zero effectively removes the outgoing cedure. The priority value zero effectively removes the outgoing
DSBM from the election procedure and makes way for the election of DSBM from the election procedure and makes way for the election of
a different DSBM. a different DSBM.
A.3. Recovering from DSBM Failure A.3. Recovering from DSBM Failure
When a DSBM fails (DSBMDeadInterval timer fires), all the SBMs When a DSBM fails (DSBMDeadIntervalTimer fires), all the SBMs
enter the ElectDSBM state and start the election process. enter the ElectDSBM state and start the election process.
At the end of the ElectionInterval, the elected DSBM sends out an At the end of the ElectionInterval, the elected DSBM sends out an
I_AM_DSBM advertisement and the DSBM is then operational. I_AM_DSBM advertisement and the DSBM is then operational.
A.4. DSBM Advertisements A.4. DSBM Advertisements
The I_AM_DSBM advertisement contains the following information: The I_AM_DSBM advertisement contains the following information:
1. DSBM address information -- contains the IP and L2 addresses 1. DSBM address information -- contains the IP and L2 addresses
of the DSBM and its SBM priority (a configuration parameter of the DSBM and its SBM priority (a configuration parameter
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
-- priority specified by a network administrator). The prior- -- priority specified by a network administrator). The prior-
ity value is used to choose among candidate SBMs during the ity value is used to choose among candidate SBMs during the
election algorithm. Higher integer values indicate higher election algorithm. Higher integer values indicate higher
priority and the value is in the range 0..255. The value zero priority and the value is in the range 0..255. The value zero
indicates that the SBM is not eligible to be the DSBM. The indicates that the SBM is not eligible to be the DSBM. The
IP address is required and used for breaking ties. The L2 IP address is required and used for breaking ties. The L2
address is for the interface of the managed segment. address is for the interface of the managed segment.
2. refresh interval -- contains the value of the refresh inter- 2. RegreshInterval -- contains the value of RefreshInterval
val in seconds. Value zero indicates the parameter has been in seconds. Value zero indicates the parameter has been
omitted in the message. Receivers may substitute their own omitted in the message. Receivers may substitute their own
default value in this case. default value in this case.
3. SBMDeadInterval -- contains the value of the SBMDeadInterval 3. DSBMDeadInterval -- contains the value of DSBMDeadInterval
in seconds. If the value is omitted (or value zero is speci- in seconds. If the value is omitted (or value zero is speci-
fied), a default value (from initial configuration) should be fied), a default value (from initial configuration) should be
used. used.
4. Miscellaneous configuration information to be advertised to 4. Miscellaneous configuration information to be advertised to
senders on the managed segment. See Appendix C for further senders on the managed segment. See Appendix C for further
details. details.
A.5. DSBM_WILLING Messages A.5. DSBM_WILLING Messages
skipping to change at page 46, line 5 skipping to change at page 46, line 5
DSBM_WILLING message contains the following information: DSBM_WILLING message contains the following information:
1. DSBM address information -- Contains the SBM's own addresses 1. DSBM address information -- Contains the SBM's own addresses
(IP and L2 address), if it wishes to be the DSBM. The IP (IP and L2 address), if it wishes to be the DSBM. The IP
address is required and used for breaking ties. The L2 address is required and used for breaking ties. The L2
address is the address of the interface for the managed seg- address is the address of the interface for the managed seg-
ment in question. Also, the DSBM address information ment in question. Also, the DSBM address information
includes the corresponding priority of the SBM whose address includes the corresponding priority of the SBM whose address
is given above. is given above.
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
A.6. SBM State Variables A.6. SBM State Variables
For each network interface, a SBM maintains the following state For each network interface, a SBM maintains the following state
variables related to the election of the DSBM for the L2 domain on variables related to the election of the DSBM for the L2 domain on
that interface: that interface:
a) LocalDSBMAddrInfo -- current DSBM's IP address (initially, a) LocalDSBMAddrInfo -- current DSBM's IP address (initially,
0.0.0.0) and priority. All IP addresses are assumed to be in 0.0.0.0) and priority. All IP addresses are assumed to be in
network byte order. In addition, current DSBM's L2 address is network byte order. In addition, current DSBM's L2 address is
also stored as part of this state information. also stored as part of this state information.
b) OwnAddrInfo -- SBM's own IP address and L2 address for the b) OwnAddrInfo -- SBM's own IP address and L2 address for the
interface and its own priority (a configuration parameter). interface and its own priority (a configuration parameter).
c) DSBM RefreshInterval in seconds. When the DSBM is not yet c) RefreshInterval in seconds. When the DSBM is not yet
elected, it is set to a default value specified as a confi- elected, it is set to a default value specified as a confi-
guration parameter. guration parameter.
d) DSBMDeadInterval in seconds. When the DSBM is not yet d) DSBMDeadInterval in seconds. When the DSBM is not yet
elected, it is initially set to a default value specified as elected, it is initially set to a default value specified as
a configuration parameter. a configuration parameter.
f) ListenInterval in seconds -- a configuration parameter f) ListenInterval in seconds -- a configuration parameter
that decides how long a SBM spends in the DetectDSBM state that decides how long a SBM spends in the DetectDSBM state
(see below). (see below).
skipping to change at page 47, line 5 skipping to change at page 47, line 5
when it has declared its candidacy. when it has declared its candidacy.
Figure 3 shows the state transition diagram for the election pro- Figure 3 shows the state transition diagram for the election pro-
tocol and the various states are described below. A complete tocol and the various states are described below. A complete
description of the state machine is provided in Section A.10. description of the state machine is provided in Section A.10.
A.7. DSBM Election States A.7. DSBM Election States
DOWN -- SBM is not operational. DOWN -- SBM is not operational.
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
DetectDSBM -- typically, the initial state of a SBM when it DetectDSBM -- typically, the initial state of a SBM when it
starts up. In this state, it checks to see whether a DSBM starts up. In this state, it checks to see whether a DSBM
already exists in its domain. already exists in its domain.
Idle -- SBM is in this state when no election is in progress Idle -- SBM is in this state when no election is in progress
and it is not the DSBM. In this state, SBM passively monitors and it is not the DSBM. In this state, SBM passively monitors
the state of the DSBM. the state of the DSBM.
ElectDSBM -- SBM is in this state when a DSBM election is in ElectDSBM -- SBM is in this state when a DSBM election is in
skipping to change at page 47, line 38 skipping to change at page 47, line 38
(other than itself) willing to be the DSBM. (other than itself) willing to be the DSBM.
DSBM_WILLING message received -- This means that the SBM DSBM_WILLING message received -- This means that the SBM
received a DSBM_WILLING message from some other SBM. Such a received a DSBM_WILLING message from some other SBM. Such a
message is sent when a SBM wishes to declare its candidacy to message is sent when a SBM wishes to declare its candidacy to
be the DSBM. be the DSBM.
I_AM_DSBM message received -- SBM received a DSBM advertise- I_AM_DSBM message received -- SBM received a DSBM advertise-
ment from the DSBM in its L2 domain. ment from the DSBM in its L2 domain.
SBMDeadInterval Timeout -- The SBMDeadInterval timer has DSBMDeadInterval Timeout -- The DSBMDeadIntervalTimer has
fired. This means that the SBM did not receive even one DSBM fired. This means that the SBM did not receive even one DSBM
advertisement during this period and indicates possible advertisement during this period and indicates possible
failure of the DSBM. failure of the DSBM.
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
RefreshInterval Timeout -- The RefreshInterval timer has RefreshInterval Timeout -- The RefreshIntervalTimer has
fired. In the I_AM_DSBM state, this means it is the time for fired. In the IAMDSBM state, this means it is the time for
sending out the next DSBM advertisement. In the ElectDSBM sending out the next DSBM advertisement. In the ElectDSBM
state, the event means that it is the time to send out state, the event means that it is the time to send out
another DSBM_WILLING message. another DSBM_WILLING message.
ElectionInterval Timeout -- The ElectionInterval timer has ElectionInterval Timeout -- The ElectionIntervalTimer has
fired. This means that the SBM has waited long enough after fired. This means that the SBM has waited long enough after
declaring its candidacy to determine whether or not it suc- declaring its candidacy to determine whether or not it suc-
ceeded. ceeded.
CONTINUED ON NEXT PAGE CONTINUED ON NEXT PAGE
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
A.9. State Transition Diagram (Figure 3) A.9. State Transition Diagram (Figure 3)
+-----------+ +-----------+
+--<--------------<-|DetectDSBM |---->------+ +--<--------------<-|DetectDSBM |---->------+
| +-----------+ | | +-----------+ |
| | | |
| | | |
| | | |
| +-------------+ +---------+ | | +-------------+ +---------+ |
skipping to change at page 50, line 5 skipping to change at page 50, line 5
-- determines whether the entity represented by the first parameter -- determines whether the entity represented by the first parameter
is better than the second entity using the priority information is better than the second entity using the priority information
and the IP address information in the two parameters. and the IP address information in the two parameters.
If any address is zero, that entity If any address is zero, that entity
automatically loses; then first priorities are compared; higher automatically loses; then first priorities are compared; higher
priority candidate wins. If there is a tie based on priority candidate wins. If there is a tie based on
the priority value, the tie is broken using the IP the priority value, the tie is broken using the IP
addresses of tied candidates (one with the higher IP address in the addresses of tied candidates (one with the higher IP address in the
lexicographic order wins). Returns TRUE if first entity is a better lexicographic order wins). Returns TRUE if first entity is a better
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
choice. FALSE otherwise. choice. FALSE otherwise.
SendDSBMWilling Message() SendDSBMWilling Message()
Begin Begin
Send out DSBM_WILLING message listing myself as a candidate for Send out DSBM_WILLING message listing myself as a candidate for
DSBM (copy OwnAddr and priority into appropriate fields) DSBM (copy OwnAddr and priority into appropriate fields)
start RefreshIntervalTimer start RefreshIntervalTimer
goto ElectDSBM state goto ElectDSBM state
End End
skipping to change at page 51, line 5 skipping to change at page 51, line 5
Action: Initialize the local state variables (LocalDSBMADDR and Action: Initialize the local state variables (LocalDSBMADDR and
LocalDSBMAddrInfo set to 0). Start the ListenIntervalTimer. LocalDSBMAddrInfo set to 0). Start the ListenIntervalTimer.
State: DetectDSBM State: DetectDSBM
New State: Idle New State: Idle
Event: I_AM_DSBM message received Event: I_AM_DSBM message received
Action: set LocalDSBMAddrInfo = IncomingDSBMAddrInfo Action: set LocalDSBMAddrInfo = IncomingDSBMAddrInfo
start DeadDSBMInterval timer start DeadDSBMInterval timer
goto Idle State goto Idle State
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
State: DetectDSBM State: DetectDSBM
Event: ListenIntervalTimer fired Event: ListenIntervalTimer fired
New State: ElectDSBM New State: ElectDSBM
Action: Start ElectionIntervalTimer Action: Start ElectionIntervalTimer
SendDSBMWillingMessage(); SendDSBMWillingMessage();
State: DetectDSBM State: DetectDSBM
Event: DSBM_WILLING message received Event: DSBM_WILLING message received
New State: ElectDSBM New State: ElectDSBM
skipping to change at page 51, line 29 skipping to change at page 51, line 29
/* am I a better choice than this dude? */ /* am I a better choice than this dude? */
If (ComparePrio(OwnAddrInfo, IncomingDSBMInfo)) { If (ComparePrio(OwnAddrInfo, IncomingDSBMInfo)) {
/* I am better */ /* I am better */
SendDSBMWillingMessage() SendDSBMWillingMessage()
} else { } else {
Change LocalDSBMAddrInfo = IncomingDSBMAddrInfo Change LocalDSBMAddrInfo = IncomingDSBMAddrInfo
goto ElectDSBM state goto ElectDSBM state
} }
State: Idle State: Idle
Event: SBMDeadInterval timer fired. Event: DSBMDeadIntervalTimer fired.
New State: ElectDSBM New State: ElectDSBM
Action: start ElectionIntervalTimer Action: start ElectionIntervalTimer
set LocalDSBMAddrInfo = OwnAddrInfo set LocalDSBMAddrInfo = OwnAddrInfo
SendDSBMWiliingMessage() SendDSBMWiliingMessage()
State: Idle State: Idle
Event: I_AM_DSBM message received. Event: I_AM_DSBM message received.
New State: Idle New State: Idle
Action: /* first check whether anything has changed */ Action: /* first check whether anything has changed */
if (!ComparePrio(LocalDSBMAddrInfo, IncomingDSBMAddrInfo)) if (!ComparePrio(LocalDSBMAddrInfo, IncomingDSBMAddrInfo))
skipping to change at page 52, line 5 skipping to change at page 52, line 5
Event: DSBM_WILLING Message is received Event: DSBM_WILLING Message is received
New State: Depends on action (ElectDSBM or Idle) New State: Depends on action (ElectDSBM or Idle)
Action: /* check whether it is from the DSBM itself (shutdown) */ Action: /* check whether it is from the DSBM itself (shutdown) */
if (IncomingDSBMAddr == LocalDSBMAddr) { if (IncomingDSBMAddr == LocalDSBMAddr) {
cancel active timers cancel active timers
Set LocalDSBMAddrInfo = OwnAddrInfo Set LocalDSBMAddrInfo = OwnAddrInfo
Start ElectionIntervalTimer Start ElectionIntervalTimer
SendDSBMWillingMessage() /* goto ElectDSBM state */ SendDSBMWillingMessage() /* goto ElectDSBM state */
} }
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
/* else, ignore it */ /* else, ignore it */
continue in current state continue in current state
State: ElectDSBM State: ElectDSBM
Event: ElectionIntervalTimer Fired Event: ElectionIntervalTimer Fired
New State: depends on action (I_AM_DSBM or Current State) New State: depends on action (IAMDSBM or Current State)
Action: If (LocalDSBMAddrInfo == OwnAddrInfo) { Action: If (LocalDSBMAddrInfo == OwnAddrInfo) {
/* I won */ /* I won */
send I_AM_DSBM message send I_AM_DSBM message
start RefreshIntervalTimer start RefreshIntervalTimer
goto I_AM_DSBM state goto IAMDSBM state
} else { /* someone else won, so wait for it to declare } else { /* someone else won, so wait for it to declare
itself to be the DSBM */ itself to be the DSBM */
set LocalDSBMAddressInfo = OwnAddrInfo set LocalDSBMAddressInfo = OwnAddrInfo
start ElectionIntervalTimer start ElectionIntervalTimer
SendDSBMWillingMessage() SendDSBMWillingMessage()
continue in current state continue in current state
} }
State: ElectDSBM State: ElectDSBM
Event: I_AM_DSBM message received Event: I_AM_DSBM message received
skipping to change at page 52, line 53 skipping to change at page 52, line 53
} }
continue in current state continue in current state
State: ElectDSBM State: ElectDSBM
Event: RefreshIntervalTimer fired Event: RefreshIntervalTimer fired
New State: ElectDSBM New State: ElectDSBM
Action: /* continue to send DSBMWilling messages until Action: /* continue to send DSBMWilling messages until
election interval ends */ election interval ends */
SendDSBMWillingMessage() SendDSBMWillingMessage()
State: I_AM_DSBM State: IAMDSBM
Event: DSBM_WILLING message received Event: DSBM_WILLING message received
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
New State: depends on action (I_AM_DSBM or SteadyState) New State: depends on action (IAMDSBM or SteadyState)
Action: /* check whether other guy is better */ Action: /* check whether other guy is better */
If (ComparePrio(OwnAddrInfo, IncomingAddrInfo)) { If (ComparePrio(OwnAddrInfo, IncomingAddrInfo)) {
/* I am better */ /* I am better */
send I_AM_DSBM message send I_AM_DSBM message
restart RefreshIntervalTimer restart RefreshIntervalTimer
continue in current state continue in current state
} else { } else {
Set LocalDSBMAddrInfo = IncomingAddrInfo Set LocalDSBMAddrInfo = IncomingAddrInfo
cancel active timers cancel active timers
start DSBMDeadInterval timer start DSBMDeadIntervalTimer
goto SteadyState goto SteadyState
} }
State: I_AM_DSBM State: IAMDSBM
Event: RefreshIntervalTimer fired Event: RefreshIntervalTimer fired
New State: I_AM_DSBM New State: IAMDSBM
Action: send I_AM_DSBM message Action: send I_AM_DSBM message
restart RefreshIntervalTimer restart RefreshIntervalTimer
State: I_AM_DSBM State: IAMDSBM
Event: I_AM_DSBM message received Event: I_AM_DSBM message received
New State: depends on action (I_AM_DSBM or Idle) New State: depends on action (IAMDSBM or Idle)
Action: /* check whether other guy is better */ Action: /* check whether other guy is better */
If (ComparePrio(OwnAddrInfo, IncomingAddrInfo)) { If (ComparePrio(OwnAddrInfo, IncomingAddrInfo)) {
/* I am better */ /* I am better */
send I_AM_DSBM message send I_AM_DSBM message
restart RefreshIntervalTimer restart RefreshIntervalTimer
continue in current state continue in current state
} else { } else {
Set LocalDSBMAddrInfo = IncomingAddrInfo Set LocalDSBMAddrInfo = IncomingAddrInfo
cancel active timers cancel active timers
start DSBMDeadInterval timer start DSBMDeadIntervalTimer
goto Idle State goto Idle State
} }
State: I_AM_DSBM State: IAMDSBM
Event: Want to shut myself down Event: Want to shut myself down
New State: DOWN New State: DOWN
Action: send DSBM_WILLING message with My address filled in, but Action: send DSBM_WILLING message with My address filled in, but
priority set to zero priority set to zero
goto Down State goto Down State
A.10.2 Suggested Values of Interval Timers A.10.2 Suggested Values of Interval Timers
To avoid DSBM outages for long period, to ensure quick recovery To avoid DSBM outages for long period, to ensure quick recovery
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
from DSBM failures, and to avoid timeout of PATH and RESV state at from DSBM failures, and to avoid timeout of PATH and RESV state at
the edge devices, we suggest the following values for various the edge devices, we suggest the following values for various
timers. timers.
Assuming that the RSVP implementations use a 30 second timeout for Assuming that the RSVP implementations use a 30 second timeout for
PATH and RESV refreshes, we suggest that the RefreshIntervalTimer PATH and RESV refreshes, we suggest that the RefreshIntervalTimer
should be set to about 5 seconds with DSBMDeadIntervalTimer set to should be set to about 5 seconds with DSBMDeadIntervalTimer set to
15 seconds (K=3, K*RefreshInterval). The DetectDSBMTimer should be 15 seconds (K=3, K*RefreshInterval). The DetectDSBMTimer should be
set to a random value between (DeadIntervalTimer, 2*DeadInterval- set to a random value between (DSBMDeadIntervalTimer, 2*DSBMDeadInterval-
Timer). The ElectionIntervalTimer should be set at least to the Timer). The ElectionIntervalTimer should be set at least to the
value of DeadIntervalTimer to ensure that each SBM has a chance to value of DSBMDeadIntervalTimer to ensure that each SBM has a chance to
have its DSBM_WILLING message (sent every RefreshInterval in have its DSBM_WILLING message (sent every RefreshInterval in
ElectDSBM state) delivered to others. ElectDSBM state) delivered to others.
A.10.3. Guidelines for Choice of Values for SBM_PRIORITY A.10.3. Guidelines for Choice of Values for SBM_PRIORITY
Network administrators should configure SBM protocol entity at Network administrators should configure SBM protocol entity at
each SBM-capable device with the device's "SBM priority" for each each SBM-capable device with the device's "SBM priority" for each
of the interfaces attached to a managed segment. SBM_PRIORITY is of the interfaces attached to a managed segment. SBM_PRIORITY is
an 8-bit, unsigned integer value (in the range 0-255) with higher an 8-bit, unsigned integer value (in the range 0-255) with higher
integer values denoting higher priority. The value zero for an integer values denoting higher priority. The value zero for an
skipping to change at page 55, line 5 skipping to change at page 55, line 5
The election algorithm works as described before in this case The election algorithm works as described before in this case
except each SBM-capable L2 device restricts the scope of the elec- except each SBM-capable L2 device restricts the scope of the elec-
tion to its local segment. As described in Section B.1 below, all tion to its local segment. As described in Section B.1 below, all
messages related to the DSBM election are sent to a special multi- messages related to the DSBM election are sent to a special multi-
cast address (AllSBMAddress). AllSBMAddress (its corresponding MAC cast address (AllSBMAddress). AllSBMAddress (its corresponding MAC
multicast address) is configured in the permanent database of multicast address) is configured in the permanent database of
SBM-capable, layer 2 devices so that all frames with AllSBMAddress SBM-capable, layer 2 devices so that all frames with AllSBMAddress
as the destination address are not forwarded and instead directed as the destination address are not forwarded and instead directed
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
to the SBM management entity in those devices. Thus, a DSBM can be to the SBM management entity in those devices. Thus, a DSBM can be
elected separately on each point-to-point segment in a switched elected separately on each point-to-point segment in a switched
topology. For example, in Figure 2, DSBM for "segment A" will be topology. For example, in Figure 2, DSBM for "segment A" will be
elected using the election algorithm between R1 and S1 and none of elected using the election algorithm between R1 and S1 and none of
the election-related messages on this segment will be forwarded by the election-related messages on this segment will be forwarded by
S1 beyond "segment A". Similarly, a separate election will take S1 beyond "segment A". Similarly, a separate election will take
place on each segment in this topology. place on each segment in this topology.
When a switched segment is a half-duplex segment, two senders (one When a switched segment is a half-duplex segment, two senders (one
skipping to change at page 56, line 5 skipping to change at page 56, line 5
the link in each direction. In this case, either one or two DSBMs the link in each direction. In this case, either one or two DSBMs
can exist on such a managed segment. If a sender at each end can exist on such a managed segment. If a sender at each end
wishes to serve as a DSBM for that end, it can declare itself to wishes to serve as a DSBM for that end, it can declare itself to
be the DSBM by sending out an I_AM_DSBM advertisement and start be the DSBM by sending out an I_AM_DSBM advertisement and start
managing the resources for the outgoing traffic over the segment. managing the resources for the outgoing traffic over the segment.
If one of the two senders does not wish itself to be the DSBM, If one of the two senders does not wish itself to be the DSBM,
then the other DSBM will not receive any DSBM advertisement from then the other DSBM will not receive any DSBM advertisement from
its peer and assume itself to be the DSBM for traffic traversing its peer and assume itself to be the DSBM for traffic traversing
in both directions over the managed segment. in both directions over the managed segment.
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
Appendix B Appendix B
Message Encapsulation and Formats Message Encapsulation and Formats
To minimize changes to the existing RSVP implementations and to To minimize changes to the existing RSVP implementations and to
ensure quick deployment of a SBM in conjunction with RSVP, all ensure quick deployment of a SBM in conjunction with RSVP, all
communication to and from a DSBM will be performed using messages communication to and from a DSBM will be performed using messages
constructed using the current rules for RSVP message formats and constructed using the current rules for RSVP message formats and
raw IP encapsulation. For more details on the RSVP message for- raw IP encapsulation. For more details on the RSVP message for-
mats, refer to the RSVP specification (RFC 2205). No changes to mats, refer to the RSVP specification (RFC 2205). No changes to
skipping to change at page 57, line 5 skipping to change at page 57, line 5
B.3. RSVP-related Message Formats B.3. RSVP-related Message Formats
All RSVP messages directed to and from a DSBM may contain various All RSVP messages directed to and from a DSBM may contain various
RSVP objects defined in the RSVP specification and messages con- RSVP objects defined in the RSVP specification and messages con-
tinue to follow the formatting rules specified in the RSVP specif- tinue to follow the formatting rules specified in the RSVP specif-
ication. In addition, an RSVP implementation must also recognize ication. In addition, an RSVP implementation must also recognize
new object classes that are described below. new object classes that are described below.
B.3.1. Object Formats B.3.1. Object Formats
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
All objects are defined using the format specified in the RSVP All objects are defined using the format specified in the RSVP
specification. Each object has a 32-bit header that contains specification. Each object has a 32-bit header that contains
length (of the object in bytes including the object header), the length (of the object in bytes including the object header), the
object class number, and a C-Type. All unused fields should be set object class number, and a C-Type. All unused fields should be set
to zero and ignored on receipt. to zero and ignored on receipt.
B.3.2. SBM Specific Objects B.3.2. SBM Specific Objects
Note that the Class-Num values for the SBM specific objects Note that the Class-Num values for the SBM specific objects
skipping to change at page 58, line 5 skipping to change at page 58, line 5
address values in higher layer protocols which might span both address values in higher layer protocols which might span both
token ring and Ethernet attached systems connected by bridges, it token ring and Ethernet attached systems connected by bridges, it
was necessary to define one reference format - the so called canon- was necessary to define one reference format - the so called canon-
ical format for these addresses. Formally the canonical format ical format for these addresses. Formally the canonical format
defines the value of the address, separate from the encoding rules defines the value of the address, separate from the encoding rules
used for transmission. It comprises a sequence of octets derived used for transmission. It comprises a sequence of octets derived
from the original wire order transmission bit order as follows. The from the original wire order transmission bit order as follows. The
least significant bit of the first octet is the first bit transmit- least significant bit of the first octet is the first bit transmit-
ted, the next least significant bit the second bit, and so on to ted, the next least significant bit the second bit, and so on to
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
the most significant bit of the first octet being the 8th bit the most significant bit of the first octet being the 8th bit
transmitted; the least significant bit of the second octet is the transmitted; the least significant bit of the second octet is the
9th bit transmitted, and so on to the most significant bit of the 9th bit transmitted, and so on to the most significant bit of the
sixth octet of the canonical format being the last bit of the sixth octet of the canonical format being the last bit of the
address transmitted. address transmitted.
This canonical format corresponds to the natural value of the This canonical format corresponds to the natural value of the
address octets for Ethernet. The actual transmission order or for- address octets for Ethernet. The actual transmission order or for-
mal encoding rules for addresses on media which do not transmit bit mal encoding rules for addresses on media which do not transmit bit
skipping to change at page 59, line 5 skipping to change at page 59, line 5
0 1 2 3 0 1 2 3
+---------------+---------------+---------------+---------------+ +---------------+---------------+---------------+---------------+
| 12 | 161 | 1 | | 12 | 161 | 1 |
+---------------+---------------+---------------+---------------+ +---------------+---------------+---------------+---------------+
| Octets 0-3 of the MAC address | | Octets 0-3 of the MAC address |
+---------------+---------------+---------------+---------------+ +---------------+---------------+---------------+---------------+
| Octets 4-5 of the MAC addr. | /// | /// | | Octets 4-5 of the MAC addr. | /// | /// |
+---------------+---------------+---------------+---------------+ +---------------+---------------+---------------+---------------+
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
/// -- unused (set to zero) /// -- unused (set to zero)
B.3.5. LAN_NHOP object B.3.5. LAN_NHOP object
LAN_NHOP object represents two objects, namely, LAN_NHOP_L3 address LAN_NHOP object represents two objects, namely, LAN_NHOP_L3 address
object and LAN_NHOP_L2 address object. object and LAN_NHOP_L2 address object.
<LAN_NHOP object> ::= <LAN_NHOP_L2 object> <LAN_NHOP_L3 object> <LAN_NHOP object> ::= <LAN_NHOP_L2 object> <LAN_NHOP_L3 object>
LAN_NHOP_L2 address object uses object class = 162 and uses the LAN_NHOP_L2 address object uses object class = 162 and uses the
skipping to change at page 60, line 5 skipping to change at page 60, line 5
IPv6 LAN_NHOP_L3 object: class =163, C-Type = 2 IPv6 LAN_NHOP_L3 object: class =163, C-Type = 2
+---------------+---------------+---------------+---------------+ +---------------+---------------+---------------+---------------+
| Length = 20 | 163 | 2 | | Length = 20 | 163 | 2 |
+---------------+---------------+---------------+---------------+ +---------------+---------------+---------------+---------------+
| IPv6 NHOP address (16 bytes) | | IPv6 NHOP address (16 bytes) |
+---------------------------------------------------------------+ +---------------------------------------------------------------+
B.3.6. LAN_LOOPBACK Object B.3.6. LAN_LOOPBACK Object
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
The LAN_LOOPBACK object gives the IP address of the outgoing inter- The LAN_LOOPBACK object gives the IP address of the outgoing inter-
face for a PATH message and uses object class=164; both IPv4 and face for a PATH message and uses object class=164; both IPv4 and
IPv6 formats are specified. IPv6 formats are specified.
IPv4 LAN_LOOPBACK object: class = 164, C-Type = 1 IPv4 LAN_LOOPBACK object: class = 164, C-Type = 1
0 1 2 3 0 1 2 3
+---------------+---------------+---------------+---------------+ +---------------+---------------+---------------+---------------+
| Length | 164 | 1 | | Length | 164 | 1 |
skipping to change at page 61, line 5 skipping to change at page 61, line 5
| /// | /// | /// | /// | PV | | /// | /// | /// | /// | PV |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Only 3 bits in data contain the user_priority value (PV). Only 3 bits in data contain the user_priority value (PV).
B.4. RSVP PATH and PATH_TEAR Message Formats B.4. RSVP PATH and PATH_TEAR Message Formats
As specified in the RSVP specification, a PATH and PATH_TEAR mes- As specified in the RSVP specification, a PATH and PATH_TEAR mes-
sages contain the RSVP Common Header and the relevant RSVP objects. sages contain the RSVP Common Header and the relevant RSVP objects.
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
For the RSVP Common Header, refer to the RSVP specification (RFC For the RSVP Common Header, refer to the RSVP specification (RFC
2205). Enhancements to an RSVP_PATH message include additional 2205). Enhancements to an RSVP_PATH message include additional
objects as specified below. objects as specified below.
<PATH Message> ::= <RSVP Common Header> [<INTEGRITY>] <PATH Message> ::= <RSVP Common Header> [<INTEGRITY>]
<RSVP_HOP_L2> <LAN_NHOP> <RSVP_HOP_L2> <LAN_NHOP>
<LAN_LOOPBACK> [<TCLASS>] <SESSION><RSVP_HOP> <LAN_LOOPBACK> [<TCLASS>] <SESSION><RSVP_HOP>
<TIME_VALUES> [<POLICY DATA>] <sender descriptor> <TIME_VALUES> [<POLICY DATA>] <sender descriptor>
skipping to change at page 62, line 5 skipping to change at page 62, line 5
All SBM-specific messages are formatted as RSVP messages with an All SBM-specific messages are formatted as RSVP messages with an
RSVP common header followed by SBM-specific objects. RSVP common header followed by SBM-specific objects.
<SBMP_MESSAGE> ::= <SBMP common header> <SBM-specific objects> <SBMP_MESSAGE> ::= <SBMP common header> <SBM-specific objects>
where <SBMP common header> ::= <RSVP common Header> [<INTEGRITY>] where <SBMP common header> ::= <RSVP common Header> [<INTEGRITY>]
For each SBM message type, there is a set of rules for the permis- For each SBM message type, there is a set of rules for the permis-
sible choice of object types. These rules are specified using sible choice of object types. These rules are specified using
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
Backus-Naur Form (BNF) augmented with square brackets surrounding Backus-Naur Form (BNF) augmented with square brackets surrounding
optional sub-sequences. The BNF implies an order for the objects in optional sub-sequences. The BNF implies an order for the objects in
a message. However, in many (but not all) cases, object order makes a message. However, in many (but not all) cases, object order makes
no logical difference. An implementation should create messages no logical difference. An implementation should create messages
with the objects in the order shown here, but accept the objects in with the objects in the order shown here, but accept the objects in
any permissible order. Any exceptions to this rule will be pointed any permissible order. Any exceptions to this rule will be pointed
out in the specific message formats. out in the specific message formats.
DSBM_WILLING Message DSBM_WILLING Message
skipping to change at page 63, line 5 skipping to change at page 63, line 5
uses <Class=42, C-Type=2>. uses <Class=42, C-Type=2>.
IPv4 DSBM IP ADDRESS object: class = 42, C-Type =1 IPv4 DSBM IP ADDRESS object: class = 42, C-Type =1
0 1 2 3 0 1 2 3
+---------------+---------------+---------------+---------------+ +---------------+---------------+---------------+---------------+
| IPv4 DSBM IP Address | | IPv4 DSBM IP Address |
+---------------+---------------+---------------+---------------+ +---------------+---------------+---------------+---------------+
IPv6 DSBM IP ADDRESS object: Class = 42, C-Type = 2 IPv6 DSBM IP ADDRESS object: Class = 42, C-Type = 2
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
+---------------+---------------+---------------+---------------+ +---------------+---------------+---------------+---------------+
| | | |
+ + + +
| | | |
+ IPv6 DSBM IP Address + + IPv6 DSBM IP Address +
| | | |
+ + + +
| | | |
+---------------+---------------+---------------+---------------+ +---------------+---------------+---------------+---------------+
skipping to change at page 64, line 5 skipping to change at page 64, line 5
+---------------+---------------+---------------+----------------+ +---------------+---------------+---------------+----------------+
NON_RESV_SEND_LIMIT Object: class = 45, C-Type = 1 NON_RESV_SEND_LIMIT Object: class = 45, C-Type = 1
0 1 2 3 0 1 2 3
+---------------+---------------+---------------+----------------+ +---------------+---------------+---------------+----------------+
| NonResvSendLimit(limit on traffic allowed to send without RESV)| | NonResvSendLimit(limit on traffic allowed to send without RESV)|
| | | |
+---------------+---------------+---------------+----------------+ +---------------+---------------+---------------+----------------+
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
<NonResvSendLimit> ::= <Intserv Sender_TSPEC object> (class=12, C-Type =2) <NonResvSendLimit> ::= <Intserv Sender_TSPEC object> (class=12, C-Type =2)
The NON_RESV_SEND_LIMIT object specifies a per-flow limit on the The NON_RESV_SEND_LIMIT object specifies a per-flow limit on the
profile of traffic which a sending host is allowed to send onto a profile of traffic which a sending host is allowed to send onto a
managed segment without a valid RSVP reservation (see Appendix C managed segment without a valid RSVP reservation (see Appendix C
for further details on the usage of this object). The object con- for further details on the usage of this object). The object con-
tains the NonResvSendLimit parameter. This parameter is equivalent tains the NonResvSendLimit parameter. This parameter is equivalent
to the Intserv SENDER_TSPEC (see RFC 2210 for contents and encoding to the Intserv SENDER_TSPEC (see RFC 2210 for contents and encoding
rules). The SENDER_TSPEC includes five parameters which describe a rules). The SENDER_TSPEC includes five parameters which describe a
skipping to change at page 65, line 5 skipping to change at page 65, line 5
= 0 and M = infinity. Of course, any of these parameters may be set = 0 and M = infinity. Of course, any of these parameters may be set
to values between zero and infinity to advertise finite per-flow to values between zero and infinity to advertise finite per-flow
limits. limits.
The NON_RESV_SEND_LIMIT object is optional. Senders on a managed The NON_RESV_SEND_LIMIT object is optional. Senders on a managed
segment should interpret the absence of the NON_RESV_SEND_LIMIT segment should interpret the absence of the NON_RESV_SEND_LIMIT
object as equivalent to an infinitely large SENDER_TSPEC (it is object as equivalent to an infinitely large SENDER_TSPEC (it is
permissible to send any traffic profile in the absence of an RSVP permissible to send any traffic profile in the absence of an RSVP
reservation). reservation).
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
Appendix C Appendix C
The DSBM as a Source of Centralized Configuration Information The DSBM as a Source of Centralized Configuration Information
There are certain configuration parameters which it may be useful There are certain configuration parameters which it may be useful
to distribute to layer-3 senders on a managed segment. The DSBM may to distribute to layer-3 senders on a managed segment. The DSBM may
serve as a centralized management point from which such parameters serve as a centralized management point from which such parameters
can easily be distributed. In particular, it is possible for the can easily be distributed. In particular, it is possible for the
network administrator configuring a DSBM to cause certain confi- network administrator configuring a DSBM to cause certain confi-
guration parameters to be distributed as objects appended to the guration parameters to be distributed as objects appended to the
skipping to change at page 66, line 5 skipping to change at page 66, line 5
segment comprised of a single 10 Mbps ethernet and 10 hosts, it may segment comprised of a single 10 Mbps ethernet and 10 hosts, it may
be acceptable to allow a 16 Kbps telephony stream to be transmitted be acceptable to allow a 16 Kbps telephony stream to be transmitted
but not a 3 Mbps video stream. but not a 3 Mbps video stream.
A more pragmatic solution then, is to allow the network administra- A more pragmatic solution then, is to allow the network administra-
tor to set a per-flow limit on the amount of non-adaptive traffic tor to set a per-flow limit on the amount of non-adaptive traffic
which a sender is allowed to generate on a managed segment in the which a sender is allowed to generate on a managed segment in the
absence of a valid reservation. This limit is advertised by the absence of a valid reservation. This limit is advertised by the
DSBM and received by sending hosts. An API on the sending host can DSBM and received by sending hosts. An API on the sending host can
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
then approve or deny an application's QoS request based on the then approve or deny an application's QoS request based on the
resources requested. resources requested.
The NON_RESV_SEND_LIMIT object can be used to advertise a Flowspec The NON_RESV_SEND_LIMIT object can be used to advertise a Flowspec
which describes the shape of traffic that a sender is allowed to which describes the shape of traffic that a sender is allowed to
generate on a managed segment when its RSVP reservation requests generate on a managed segment when its RSVP reservation requests
have either not yet completed or have been rejected. have either not yet completed or have been rejected.
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
ACKNOWLEDGEMENTS ACKNOWLEDGEMENTS
Authors are grateful to Eric Crawley (Argon), Russ Fenger (Intel), Authors are grateful to Eric Crawley (Argon), Russ Fenger (Intel),
David Melman (Siemens), Ramesh Pabbati (Microsoft), Mick Seaman David Melman (Siemens), Ramesh Pabbati (Microsoft), Mick Seaman
(3COM), Andrew Smith (Extreme Networks) for their constructive com- (3COM), Andrew Smith (Extreme Networks) for their constructive com-
ments on the SBM design and the earlier versions of this document. ments on the SBM design and the earlier versions of this document.
6. Authors` Addresses 6. Authors` Addresses
skipping to change at page 68, line 5 skipping to change at page 68, line 5
phone: +1 408 526 4257 phone: +1 408 526 4257
email: fred@cisco.com email: fred@cisco.com
Michael Speer Michael Speer
Sun Microsystems, Inc Sun Microsystems, Inc
901 San Antonio Road UMPK15-215 901 San Antonio Road UMPK15-215
Palo Alto, CA 94303 Palo Alto, CA 94303
phone: +1 650-786-6368 phone: +1 650-786-6368
email: speer@Eng.Sun.COM email: speer@Eng.Sun.COM
SBM (Subnet Bandwidth Manager) March, 1999 SBM (Subnet Bandwidth Manager) October, 1999
 End of changes. 118 change blocks. 
133 lines changed or deleted 138 lines changed or added

This html diff was produced by rfcdiff 1.33. The latest version is available from http://tools.ietf.org/tools/rfcdiff/