Network Working Group E. Lear Internet-Draft K. Crozier Expires:
December 6, 2004April 18, 2005 Cisco Systems June 7,October 18, 2004 BEEP Application Protocol Mapping forUsing the NETCONF draft-ietf-netconf-beep-01Protocol over Blocks Extensible Exchange Protocol (BEEP) draft-ietf-netconf-beep-02 Status of this Memo This document is an Internet-DraftBy submitting this Internet-Draft, I certify that any applicable patent or other IPR claims of which I am aware have been disclosed, and isany of which I become aware will be disclosed, in full conformanceaccordance with all provisions of Section 10 of RFC2026.RFC 3668. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http:// www.ietf.org/ietf/1id-abstracts.txt.http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on December 6, 2004.April 18, 2005. Copyright Notice Copyright (C) The Internet Society (2004). All Rights Reserved. Abstract This document specifies an application protocol mapping for the NETCONF protocol over the Blocks Extensible Exchange Protocol (BEEP). Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 Why BEEP? . . . . . . . . . . . . . . . . . . . . . . . . .3 2. BEEP Transport Mapping . . . . . . . . . . . . . . . . . . . . 4 2.1 NETCONF Session Initiation . . .Establishment . . . . . . . . . . . . . . 4 2.2 NETCONF RPC Execution .Capabilities Exchange . . . . . . . . . . . . . . . . . . 4 2.3 NETCONF Session TeardownUsage . . . . . . . . . . . . . . . . . . 54 2.4 BEEP Profile forNETCONF .Session Teardown . . . . . . . . . . . . . . . . . 5 2.4.1 Operations Channel2.5 BEEP Profile for NETCONF . . . . . . . . . . . . . . . . . 5 2.4.2 Notification Channel2.5.1 BEEP Profile . . . . . . . . . . . . . . . . 7. . . . 5 3. Security Considerations . . . . . . . . . . . . . . . . . . . 8 4. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 9 5. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 10 6. References . . . . . . . . . . . . . . . . . . . . . . . . . . 11 6.1 Normative References . . . . . . . . . . . . . . . . . . . . 11 6.2 Informative References . . . . . . . . . . . . . . . . . . . 1211 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . 12 A. Change Log . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Intellectual Property and Copyright Statements . . . . . . . . 14 1. Introduction The NETCONF protocol  defines a simple mechanism through which a network device can be managed. NETCONF is designed to be usable over a variety of application protocols. This document specifies an application protocol mapping for NETCONF over the Blocks Extensible Exchange Protocol (BEEP)  . The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 .. 1.1 Why BEEP? Use of BEEP is natural as an application protocol for transport of XML. As a peer to peer protocol, BEEP provides an easy way to implement NETCONF, no matter which side of the connection was the initiator. This "bidirectionality" allows for either side to play the role of the manager with no protocol changes. Either side can open a channel. Either side could initiate an RPC. This is particularly important to support operational models that involve small devices connecting to a manager, and those devices that must reverse the management connection in the face of firewalls and NATs. The SASL profile used by BEEP allows for a simple and direct mapping to the existing security model for CLI, while TLS provides a strong well tested encryption mechanism with either server or server and client-side authentication. 2. BEEP Transport Mapping All NETCONF over BEEP implementations MUST implement the profile and functional mapping between NETCONF and BEEP as described below. 2.1 NETCONF Session InitiationEstablishment Managers may be either BEEP listeners or initiators. Similarly, agents may be either listeners or initiators. Thus the initial exchange takes place without regard to whether a manager or the agent is the initiator. After the transport connection is established, as greetings are exchanged, they should each announce their support for TLS  and optionally SASL  (see below), as well as for the SYSLOG profile .. Once greetings are exchanged, if TLS is to be used and available by both parties, the listener STARTs a channel with the TLS profile. Once TLS has been started, a new greeting is sent by both initiator and listener, as required by the BEEP RFC. At this point, if SASL is desired, the initiator starts BEEP channel 1 to perform a SASL exchange to authenticate itself. When SASL is completed, the channel MUST be closed. Once authentication has occurred, there is no need to distinguish between initiator and listener. We now distinguish between manager and agent. 2.2 Capabilities Exchange The manager now establishes an NETCONF a new &dquot;operational&dquot; channel for capabilitiesexchange and requests and responses.channel. As initiators assign odd channels and listeners assign even channels, this next channel is BEEP channel 1 or 2, depending on whether the manager is the initiator or the listener. Certain NETCONF capabilities may require additional BEEP channels. When such capabilities are defined, a BEEP mapping must be defined as well. At this point, the NETCONF session is established. 2.2established, and capabilities have been exchanged. 2.3 NETCONF RPC ExecutionSession Usage Nearly all NETCONF operations are executed through the <RPC> tag. To issue an RPC, the manager transmits on the operational channel a BEEP MSG containing the RPC and its arguments. In accordance with the BEEP standard, RPC requests may be split across multiple BEEP frames. Once received and processed, the agent responds with BEEP RPYs on the same channel with the response to the RPC. In accordance with the BEEP standard, responses may be split across multiple BEEP frames. 2.32.4 NETCONF Session Teardown Either side may initiate the terminationUpon receipt of <close-session> from the manager, once the agent has completed all RPCs, it will close BEEP channel 0. When an NETCONF session. In This is done by issuingagent needs to initiate a BEEPclose onit will do so by closing BEEP channel 0 after0. Although not required to do so, the current RPCagent should allow for a reasonable period for a manager to release an existing lock prior to initiating a close. Once the agent has completed.closed channel 0, all locks are released, and each side follows tear down procedures as specified in . Having sent orreceived a BEEP close,close or having sent <close-session>, a manager MUST NOT send further requests, and an agent MUST NOT send additional responses.requests. If there are additional activities due to expanded capabilities, these MUST cease in an orderly manner, and should be properly described in the capability mapping. 2.42.5 BEEP Profile for NETCONF The operations channel will have two commands,There are three commands in the BEEP profile. <rpc> and <rpc-reply>. 2.4.1 Operations Channel2.5.1 BEEP Profile <!-- DTD for netconf operations over BEEP Refer to this DTD as: <!ENTITY % NETCONF PUBLIC "netconf/Operation/1.0" ""> %NETCONF; --> <!-- Contents Overview Includes Profile Summaries Entity Definitions Operations rpc rpc-reply --> <!-- Overview NETCONF operation channel --> <!-- Includes --> <!ENTITY % BEEP PUBLIC "-//Blocks//DTD BEEP//EN" ""> %BEEP; <!-- Profile summaries BEEP profile NETCONF-MANAGEMENTNETCONF role MSG RPY ERR ==== === === === I or L rpc ok error I or L rpc-reply ok error --> <!-- Entity Definitions entity syntax/reference example ====== ================ ======= a PRCRPC RPC-DATA Alpha a RPC reply number RPC-REPLY 1*3DIGIT --> <!ENTITY % RPC-REPLY "CDATA"> <!ENTITY % RPC-DATA "CDATA"> --> <!-- RPC command --> <!ELEMENT RPC (#PCDATA)> <!ATTLIST RPC RPC-DATA %RPC_DATA; #REQUIRED> <!-- Result of RPC. --> <!ELEMENT RPC-REPLY (#PCDATA)> <!ATTLIST RPC-REPLY RPC-REPLY %RPC-REPLY; #REQUIRED RPC-DATA %RPC-DATA #REQUIRED> <!-- End of DTD --> 2.4.2 Notification Channel Profile The NETCONF notification channel profile is defined in RFC 3195 .3. Security Considerations Configuration information is by its very nature sensitive. Its transmission in the clear and without integrity checking leaves devices open to classic so-called "person in the middle" attacks. Configuration information often times contains passwords, user names, service descriptions, and topological information, all of which are sensitive. A NETCONF application protocol, therefore, must minimally support options for both confidentiality and authentication. BEEP makes use of both transport layer security and SASL. We require that TLS be used in BEEP as described by the BEEP standard. Client-side certificates are strongly desirable, but an SASL authentication is the bare minimum. SASL allows for the use of protocols such as RADIUS ,, so that authentication can occur off the box. SASL authentication will occur on the first channel creation, and prior to issuance of any protocol operations. No further authentication may occur during the same session. This avoids a situation where rights are different between different channels. If an implementation wishes to support multiple accesses by different individuals with different rights, then multiple sessions are required. Different environments may well allow different rights prior to and then after authentication. Thus, anAn authorization model is not specified in this document. When an operation is not properly authorized then a simple "permission denied" is sufficient. Note that authorization information may be exchanged in the form of configuration information, which is all the more reason to ensure the security of the connection. 4. IANA Considerations The IANA will assign a TCP port for NETCONF. 5. Acknowledgments This work is the product of the NETCONF IETF working group, and many people have contributed to the NETCONF discussion. Most notably, Rob Ens, Phil Schafer, Andy Bierman, Wes Hardiger, Ted Goddard, and Margaret Wasserman all contributed in some fashion to this work, which was originally to be found in the NETCONF base protocol specification. Thanks also to Weijing Chen, Keith Allen, Juergen Schoenwaelder, and Eamon O'Tuathail for their very constructive participation. 6. References 6.1 Normative References  Enns, R., "NETCONF Configuration Protocol", draft-ietf-netconf-prot-01draft-ietf-netconf-prot-03 (work in progress), October 2003.June 2004.  Rose, M., "The Blocks Extensible Exchange Protocol Core", RFC 3080, March 2001.  Rose, M., "Mapping the BEEP Core onto TCP", RFC 3081, March 2001.  Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997.  Myers, J., "Simple Authentication and Security Layer (SASL)", RFC 2222, October 1997.  Dierks, T., Allen, C., Treese, W., Karlton, P., Freier, A. and P. Kocher, "The TLS Protocol Version 1.0", RFC 2246, January 1999.  New, D. and M. Rose, "Reliable Delivery for syslog", RFC 3195, November 2001. 6.2 Informative References  Bray, T., Paoli, J., Sperberg-McQueen, C. and E. Maler, "Extensible Markup Language (XML) 1.0 (Second Edition)", W3C REC REC-xml-20001006, October 2000.  Hollenbeck, S., Rose, M. and L. Masinter, "Guidelines for the Use of Extensible Markup Language (XML) within IETF Protocols", BCP 70, RFC 3470, January 2003.  Rigney, C., Willens, S., Rubens, A. and W. Simpson, "Remote Authentication Dial In User Service (RADIUS)", RFC 2865, June 2000. Authors' Addresses Eliot Lear Cisco Systems 170 W. Tasman Dr. San Jose, CA 95134-1706 USGlatt-com Glattzentrum, Zurich 8301 CH EMail: email@example.com Ken Crozier Cisco Systems 170 W. Tasman Dr. San Jose, CA 95134-1706 US EMail: firstname.lastname@example.org Appendix A. Change Log 02: added comments about locking 01: Removed management channel, rpc-status, rpc-abort, and associated profile changes. Intellectual Property Statement The IETF takes no position regarding the validity or scope of any intellectual propertyIntellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; neithernor does it represent that it has made any independent effort to identify any such rights. Information on the IETF'sprocedures with respect to rights in standards-track and standards-related documentationRFC documents can be found in BCP-11.BCP 78 and BCP 79. Copies of claims of rightsIPR disclosures made available for publicationto the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementorsimplementers or users of this specification can be obtained from the IETF Secretariat.on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights whichthat may cover technology that may be required to practiceimplement this standard. Please address the information to the IETF Executive Director. Full Copyright Statement Copyright (C) The Internet Society (2004). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purposeat email@example.com. Disclaimer of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assignees.Validity This document and the information contained herein isare provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMSDISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Copyright Statement Copyright (C) The Internet Society (2004). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. Acknowledgment Funding for the RFC Editor function is currently provided by the Internet Society.