Definitions of Managed Objects
                     for the DS3/E3 Interface Type

                        Tue Oct 24 22:34:37 1995

                   draft-ietf-trunkmib-ds3-mib-00.txt

                        Thu Feb  8 19:48:26 1996

                   draft-ietf-trunkmib-ds3-mib-01.txt

                         David Fowler (editor)
                           Newbridge Networks
                          davef@newbridge.com

Status of this Memo

   This document is an Internet-Draft.  Internet-Drafts are working
   documents of the Internet Engineering Task Force (IETF), its areas,
   and its working groups. Note that other groups may also distribute
   working documents as Internet-Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as ``work in progress.''

   To learn the current status of any Internet-Draft, please check the
   ``1id-abstracts.txt'' listing contained in the Internet-Drafts Shadow
   Directories on ds.internic.net (US East Coast), nic.nordu.net
   (Europe), ftp.isi.edu (US West Coast), or munnari.oz.au (Pacific
   Rim).

Abstract

   This memo defines an experimental portion of the Management
   Information Base (MIB) for use with network management protocols in
   the Internet community.  In particular, it describes objects used for
   managing DS3 and E3 interfaces.  This document is a companion
   document with Definitions of Managed Objects for the DS1/E1 DS1/E1/DS2/E2
   and SONET/SDH Interface Types, rfc1406 [8] [6]
    and rfc1595 [9]. [7].

   This memo specifies a MIB module in a manner that is both compliant
   to the SNMPv2 SMI, and semantically identical to the peer SNMPv1
   definitions.

   This memo does not specify a standard for the Internet community.

   This document entirely replaces RFC 1233, which contains a
   fundamental error: many objects are encoded as Counters that must be
   encoded as Integer32s or Gauge32s.  The magnitude of the change
   required is sufficient that virtually every object changed.
   Therefore, the MIB documented in RFC 1233 should not be implemented. 1407.

1.  The SNMPv2 Network Management Framework

   The SNMPv2 SNMP Network Management Framework presently consists of four three major
     components.  They are:

   0    RFC 1442 [1] which defines

   o    the SMI, described in RFC 1902 [1] - the mechanisms used for
        describing and naming objects for the purpose of management.

   0

   o    the MIB-II, STD 17, RFC 1213 [2] defines MIB-II, - the core set of managed
        objects for the Internet suite of protocols.

   0

   o    the protocol, RFC 1445 1157 [3] which defines the administrative and other
        architectural aspects of the framework.

   0 and/or RFC 1448 [4] which defines 1905 [4], - the protocol used
        for network
        access to accessing managed objects.

   The Framework permits new objects to be defined for the purpose of
   experimentation and evaluation.

2.  Objects  Object Definitions

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  Objects in the MIB are
   defined using the subset of Abstract Syntax Notation One (ASN.1)
   defined in the SMI.  In particular, each object type is named by an
   OBJECT IDENTIFIER, an administratively assigned name.  The object
   type together with an object instance serves to uniquely identify a
   specific instantiation of the object.  For human convenience, we
   often use a textual string, termed the descriptor, to also refer to
   the object type.

2.1.  Changes from RFC1233 RFC1407

   This MIB obsoletes RFC1233. RFC1407.  The changes from RFC1233 RFC1407 are the
   following:

     --  This MIB module contains information to manage
         an E3 interface, also.

     --  This MIB module contains three groups:
          DS3/E3 Near End Group which is mandatory,
          DS3 Far End Group which is optional, and
          DS3 Fractional Group which is optional.

     --  The DS3 Far End Group is a new group and contains
         configuration information and statistics
         that are collected from the far end DS3/E3 interface.
         Presently, the Far End Group may only be implemented by
         DS3 systems that use C-bit Parity or SYNTRAN.

     --

        (1)  The DS3 Fractional Group is a new group and is
         modeled after the DS1 Fractional Group.

     --  ds3CSUIndex Table has been redefined and renamed
         to dsx3LineIndex. deprecated

        (2)  This object
         is the identifier document uses SMIv2

        (3)  Values are given for ifTable and ifXTable

        (4)  Example usage of a DS3/E3 Interface on a device.
         On a CSU, a single DS3/E3 data stream will cross two DS3/E3
         interfaces, which have separate ifStackTable is included

        (5)  dsx3IfIndex and dsx3LineIndex values.

     --  ds3Index have been deprecated

        (6)  The definition of valid intervals has been redefined and renamed to
         dsx3IfIndex.  This value clarified
             for this
         object is equal to the value of ifIndex from case where the Interfaces
         table of MIB II (STD 17, RFC 1213).

     --  The ACCESS agent proxied for objects in other
             devices.  In particular, the dsx3ConfigTable treatment of missing
             intervals has been set to read-write for items that are configurable.

     --  The dsx3ZeroCoding clarified.

        (7)  An inward loopback has been renamed to dsx3LineCoding.

     --  A new object has been added called dsx3LoopbackConfig,
         which better describes the loopback capabilities of
         a DS3/E3 interface on a device.

     --  The dsx3SendCode object has been updated to reflect
         different types of loopback messages.

     --  A new object has been added called dsx3LineStatus.
         This object better describes the status (e.g.,
         failure state and loopback state) of a
         DS3/E3 interface.

     --  A new object has been added called dsx3TransmitClockSource.
         This object identifies the source for the transmit clock.

     --  All Counters added.

        (8)  Additional lineStatus bits have been changed to Gauge32s.

     --  A Line Errored Seconds object has been added to
         all near end tables.

     --  Line Coding Violations are counted instead of Bipolar
         Violations.

     --  A new Coding Violation counter has been added to count
         coding violations reported via the C-bits for Near End
             in Unavailable Signal State, Carrier Equipment Out of SYNTRAN
             Service, DS@ Payload AIS, and C-bit Parity DS3 applications.
         The original Coding Violation counter has been renamed
         to PCV to mean coding violations reported via the P-bits.
         This count is also added for symmetry with the far end
         statistics.

     -- DS@ Performance Threshold

        (9)  A new Errored Second counter and Severely Errored Second
         counter line Length object has been added to count these performance events
         via the C-bits of the SYNTRAN and C-bit Parity DS3
         applications.  The original ES and SES counters have been
         renamed to PES added.

        (10) Added a lineStatus last change, trap and PSES to mean reported via the P-bits.
         These counts are also added for symmetry with the far end
         statistics. enabler.

3.  Overview

   These objects are used when the particular media being used to
   realize an interface is a DS3/E3 interface.  At present, this applies
   to these values of the ifType variable in the Internet-standard MIB:

        ds3 (30)

   The DS3 definitions contained herein are based on the DS3
   specifications in ANSI T1.102-1987, ANSI T1.107-1988, ANSI T1.107a-
   1990, and ANSI T1.404-1989 [10,11,11a,12]. [8,9,9a,10].  The E3 definitions contained
   herein are based on the E3 specifications in CCITT G.751
   [14]. [12].

3.1.  Use of ifTable for DS1 DS3 Layer

   Only the ifGeneralGroup needs to be supported.

           ifTable Object    Use for DS1 DS3 Layer
======================================================================
           ifIndex           Interface index.

           ifDescr           Textual Description of the interface

           ifType            ds3(30)

           ifSpeed           Speed of line rate for DS3,
                             (either 43232000 or 30912000 bps).
                             DS3 - 44736000
                             E3  - 34368000

           ifPhysAddress     The value of the Circuit Identifier.
                             If no Circuit Identifier has been assigned
                             this object should have an octet string with
                             zero length.

           ifAdminStatus     Supports read-only access.
                             The desired administrative status of the
                             interface.

           ifOperStatus      The current operational status of the
                             interface.

           ifLastChange      sysUpTime at the last change in
                             ifOperStatus.

           ifName            Textual name of the interface or an
                             OCTET STRING of zero length.

           ifLinkUpDownTrapEnable   Set to enabled(1).
                                    Supports read-only access.

           ifHighSpeed       Speed of line in Mega-bits per second
                             (either 43 45 or 31) 34)

           ifConnectorPresent Set to true(1). true(1) normally, except for
                              cases such as DS3/E3 over AAL1/ATM where
                              false(2) is appropriate

3.2.  Using ifStackTable

   The objects dsx3IfIndex and dsx3LineIndex have been deprecated.
   These objects previously allowed a very special proxy situation to
   exist for Routers and CSUs. This section now describes how to use
   ifStackTable to represent this relationship.

   The paragraphs discussing dsx3IfIndex and dsx3LineIndex have been
   preserved in Appendix A for informational purposes.

   External&Internal interface scenario: the SNMP Agents resides on an
   host external from the device supporting DS3/E3 interfaces (e.g., a
   router). The Agent represents both the host and the DS3/E3 device.
   The index dsx3LineIndex is used

   Example:

   A shelf full of CSUs connected to not only represent the DS3/E3
   interfaces external from the host/DS3/E3-device combination, but also
   the DS3/E3 interfaces connecting the host and the DS3/E3 device.  The
   index dsx3IfIndex is always equal to ifIndex.

   Example:

   A shelf full of CSUs connected to a Router. An SNMP Agent residing on a Router. An SNMP Agent residing on
   the router proxies for itself and the CSU. The router has also an
   Ethernet interface:

         +-----+
   |     |     |
   |     |     |               +---------------------+
   |E    |     |  44.736 MBPS  |   ds3 M13    Line#A | ds3 C-bit Parity
   |t    |  R  |---------------+ - - - - -  - - -  - +------>
   |h    |     |               |                     |
   |e    |  O  |  44.736 MBPS  |   ds3 M13    Line#B | ds3 C-bit Parity
   |r    |     |---------------+ - - - - - - - - - - +------>
   |n    |  U  |               |                     |
   |e    |     |  44.736 MBPS  |   ds3 M13    Line#C | ds3 C-bit Parity
   |t    |  T  |---------------+ - - - -- -- - - - - +------>
   |     |     |               |                     |
   |-----|  E  |  44.736 MBPS  |   ds3 M13    Line#D | ds3 C-bit Parity
   |     |     |---------------+ -  - - - -- - - - - +------>
   |     |  R  |               |_____________________|
   |     |     |
   |     +-----+

   The assignment of the index values could for example be:

           ifIndex  Description
           1        Ethernet
           2        Line#A Router
           3        Line#B Router
           4        Line#C Router
           5        Line#D Router
           6        Line#A CSU Router
           7        Line#B CSU Router
           8        Line#C CSU Router
           9        Line#D CSU Router
           10       Line#A CSU Network
           11       Line#B CSU Network
           12       Line#C CSU Network
           13       Line#D CSU Network
   The ifStackTable is then used to show the relationships between the
   various DS3 interfaces.

           ifStackTable Entries

           HigherLayer   LowerLayer
           2             6
           3             7
           4             8
           5             9
           6             10
           7             11
           8             12
           9             13

   If the CSU shelf is managed by itself by a local SNMP Agent, the
   situation would be identical, except the Ethernet and the 4 router
   interfaces are deleted.  Interfaces would also be numbered from 1 to
   8.

           ifIndex  Description
           1        Line#A CSU Router
           2        Line#B CSU Router
           3        Line#C CSU Router
           4        Line#D CSU Router
           5        Line#A CSU Network
           6        Line#B CSU Network
           7        Line#C CSU Network
           8        Line#D CSU Network

           ifStackTable Entries

           HigherLayer   LowerLayer
           1             5
           2             6
           3             7
           4             8

3.3.  Objectives of this MIB Module

   There are numerous things that could be included in a MIB for DS3/E3
   signals:  the management of multiplexors, CSUs, DSUs, and the like.
   The intent of this document is to facilitate the common management of
   all devices with DS3/E3 interfaces.  As such, a design decision was
   made up front to very closely align the MIB with the set of objects
   that can generally be read from DS3/E3 devices that are currently
   deployed.

3.4.  DS3/E3 Terminology

   The terminology used in this document to describe error conditions on
   a DS3 interface as monitored by a DS3 device are based on the
   definitions from the ANSI T1.231 standard [13]. [11].  If the definition in
   this document does not match the definition in the ANSI T1.231
   document, the implementer should follow the definition described in
   this document.

3.4.1.  Error Events

          Bipolar Violation (BPV) Error Event
            A bipolar violation error event, for B3ZS(HDB3)-coded
            signals, is the occurrence of a pulse of the same polarity
            as the previous pulse without being part of the zero
            substitution code, B3ZS(HDB3).  For B3ZS(HDB3)-coded
            signals, a bipolar violation error event may also include
            other error patterns such as:  three(four) or more
            consecutive zeros and incorrect polarity. (See T1.231)

          Excessive Zeros (EXZ) Error Event
            An EXZ is the occurrence of any zero string length equal
            to or greater than 3 for B3ZS, or greater than 4 for HDB3.
            (See T1.231)

          Line Coding Violation (LCV) Error Event
            This parameter is a count of both BPVs and EXZs
            occurring over the accumulation period.  An EXZ
            increments the LCV by one regardless of the length
            of the zero string.

          P-bit Coding Violation (PCV) Error Event
            For all DS3 applications, a coding violation error
            event is a P-bit
            Parity Error event.  A P-bit Parity Error event is the
            occurrence of a received P-bit code on the DS3 M-frame
            that is not identical to the corresponding locally-
            calculated code. (See T1.231)

          C-bit Coding Violation (CCV) Error Event
            For C-bit Parity and SYNTRAN DS3 applications, this is
            the count of coding violations reported via the C-bits.

            For C-bit Parity, it is a count of CP-bit parity errors
            occurring in the accumulation interval.  For SYNTRAN, it
            is a count of CRC-9 errors occurring in the accumulation
            interval. (See T1.231)

3.4.2.  Performance Parameters

   All performance parameters are accumulated in fifteen minute
   intervals and up to 96 intervals (24 hours worth) are kept by an
   agent.  Fewer than 96 intervals of data will be available if the
   agent has been restarted within the last 24 hours.  In addition,
   there is a rolling 24-hour total of each performance parameter.

   There is no requirement for an agent to ensure fixed relationship
   between the start of a fifteen minute interval and any wall clock;
   however some agents may align the fifteen minute intervals with
   quarter hours.

   Performance parameters are of type Gauge32 because it is possible for
   these objects to decrease.  Objects may decrease when Unavailable
   Seconds occurs across a fifteen minutes interval boundary. See
   Unavailable Seconds discussion later in this section.
          Line Errored Seconds (LES)
            A Line Errored Second is a second in which one or more CV
            occurred OR one or more LOS defects.  (See T1.231)

          P-bit Errored Seconds (PES)
            An PES is a second with one or more PCVs OR one or more
            Out of Frame defects OR a detected incoming AIS. This
            gauge is not incremented when UASs are counted. (See T1.231)

          P-bit Severely Errored Seconds (PSES)
            A PSES is a second with 44 or more PCVs OR one or more
            Out of Frame defects OR a detected incoming AIS. This
            gauge is not incremented when UASs are counted. (See T1.231)

          C-bit Errored Seconds (CES)
            An CES is a second with one or more CCVs OR
            one or more Out of Frame defects OR a detected incoming AIS.
            This count is only for the SYNTRAN and C-bit Parity DS3
            applications. This gauge is not incremented when UASs are
            counted. (See T1.231)

          C-bit Severely Errored Seconds (CSES)
            A CSES is a second with 44 or more CCVs OR
            one or more Out of Frame defects OR a detected incoming AIS.
            This count is only for the SYNTRAN and C-bit Parity DS3
            applications.  This gauge is not incremented when UASs
            are counted. (See T1.231)

          Severely Errored Framing Seconds (SEFS)
            A SEFS is a second with one or more Out of Frame defects
            OR a detected incoming AIS. (See T1.231)

          Unavailable Seconds (UAS)
            UAS are calculated by counting the number of seconds that
            the interface is unavailable.  The DS3 interface is said
            to be unavailable from the onset of 10 contiguous PSESs, or
            the onset of the condition leading to a failure (see Failure
            States).  If the condition leading to the failure was
            immediately preceded by one or more contiguous PSESs, then
            the DS3 interface unavailability starts from the onset of
            these PSESs.  Once unavailable, and if no failure is
            present, the DS3 interface becomes available at the onset
            of 10 contiguous seconds with no PSESs.  Once unavailable,
            and if a failure is present, the DS3 interface becomes
            available at the onset of 10 contiguous seconds with no
            PSESs, if the failure clearing time is less than
            or equal to 10 seconds.  If the failure clearing time is
            more than 10 seconds, the DS3 interface becomes available
            at the onset of 10 contiguous seconds with no PSESs, or
            the onset period leading to the successful clearing
            condition, whichever occurs later. With respect to the
            DS3 error counts, all counters are incremented
            while the DS3 interface is deemed available.  While the
            interface is deemed unavailable, the only count that is
            incremented is UASs. (See T1.231)

            A special case exists when the 10 or more second period
            crosses the 900 second statistics window boundary, as the
            foregoing description implies that the PSES and UAS
            counters for the PREVIOUS interval must be adjusted when
            the Unavailable Signal State is entered. Clearly,
            successive GETs of the affected dsx3IntervalPSESs and
            dsx3IntervalUASs objects will return differing values
            if the first GET occurs during the first few seconds of
            the window.  This is viewed as an unavoidable side-effect
            of selecting the presently defined managed objects as
            a basis for this memo.

            To summarize, when the unavialable state is entered, SES
            is reduced by 10 and UAS is increased by 10.  The linkDown
            trap is sent at the start of the unavailable period, but
            the time on the trap will be tate of the first UAS,
            (i.e. 10 seconds earlier).

            The UAS effect can be acheived by using a delay technique.
            This is described in Appendix B.

3.4.3.  Performance Defects

          Failure States:
            The Remote Alarm Indication (RAI) failure, in SYNTRAN
            applications, is declared after detecting
            the Yellow Alarm Signal on the alarm channel.  See ANSI
            T1.107a-1990 [11a]. [9a]. The Remote Alarm Indication failure,
            in C-bit Parity DS3 applications, is declared
            as soon as the presence of either one or two alarm signals
            are detected on the Far End Alarm Channel.  See [11]. [9].
            The Remote Alarm Indication failure may also be declared
            after detecting the far-end SEF/AIS defect (aka yellow).
            The Remote Alarm Indication failure is cleared as soon as
            the presence of the any of the above alarms are removed.

            Also, the incoming failure state is declared when a defect
            persists for at least 2-10 seconds.  The defects are
            the following:  Loss of Signal (LOS), an Out of Frame (OOF)
            or an incoming Alarm Indication Signal (AIS).
            The Failure State is cleared when the defect is absent
            for less than or equal to 20 seconds.

          Far End SEF/AIS defect (aka yellow)
            A Far End SEF/AIS defect is the occurrence of the two X-bits
            in a M-frame set to zero.  The Far End SEF/AIS defect is
            terminated when the two X-bits in a M-frame are set to
            one. (See T1.231)

          Out of Frame (OOF) defect
            A DS3 OOF defect is detected when any three or more errors
            in sixteen or fewer consecutive F-bits occur within a DS3
            M-frame.  An OOF defect may also be called a Severely
            Errored Frame (SEF) defect.  An OOF defect is cleared when
            reframe occurs.  A DS3 Loss of Frame (LOF) failure is
            declared when the DS3 OOF defect is consistent for 2 to 10
            seconds.  The DS3 OOF defect ends when reframe occurs.
            The DS3 LOF failure is cleared when the DS3 OOF
            defect is absent for 10 to 20 seconds. (See T1.231)

            An E3 OOF defect is detected when four consecutive frame
            alignment signals have been incorrectly received in there
            predicted positions in an E3 signal. E3 frame alignment
            occurs when the presence of three consecutive frame
            alignment signals have been detected.

          Loss of Signal (LOS) defect
            The DS3 LOS defect is declared upon observing 175 +/- 75
            contiguous pulse positions with no pulses of either
            positive or negative polarity.
            The DS3 LOS defect is terminated upon observing an average
            pulse density of at least 33% over a period of 175 +/- 75
            contiguous pulse positions starting with the receipt of a
            pulse. (See T1.231)

          Alarm Indication Signal (AIS) defect
            The DS3 AIS is framed with "stuck stuffing."  This implies
            that it has a valid M-subframe alignments bits, M-frame
            alignment bits, and P bits.  The information bits are set
            to a 1010... sequence, starting with a one (1) after each
            M-subframe alignment bit, M-frame alignment bit, X bit, P
            bit, and C bit.  The C bits are all set to zero giving
            what is called "stuck stuffing."  The X bits are set to
            one. The DS3 AIS defect is declared after DS3 AIS is
            present in contiguous M-frames for a time equal to or
            greater than T, where 0.2 ms <= T <= 100 ms.
            The DS3 AIS defect is terminated after AIS is absent in
            contiguous M-frames for a time equal to or greater than T.

            The E3 binary content of the AIS is nominally a continuous
            stream of ones.  AIS detection and the application of
            consequent actions, should be completed within a time
            limit of 1 ms. (See T1.231)

3.4.4.  Other Terms
          Circuit Identifier
            This is a character string specified by the circuit
            vendor, and is useful when communicating with the vendor
            during the troubleshooting process.

4.  Object Definitions

          DS3-MIB DEFINITIONS ::= BEGIN

          IMPORTS
               MODULE-IDENTITY, OBJECT-TYPE, Gauge32 Gauge32, NOTIFICATION-TYPE
                     FROM SNMPv2-SMI
               DisplayString
               DisplayString, TimeStamp
                     FROM SNMPv2-TC
               MODULE-COMPLIANCE, OBJECT-GROUP
                     FROM SNMPv2-CONF
               ifIndex,
               transmission
                     FROM RFC1213-MIB; RFC1213-MIB
               ifIndex
                     FROM IF-MIB;

          --  This is the MIB module for the DS3 and E3 Interface
          --  objects.

          ds3 MODULE-IDENTITY
              LAST-UPDATED "9510250400Z" "9602032200Z"
              ORGANIZATION "IETF Trunk MIB Working Group"
              CONTACT-INFO
                "        David Fowler

                 Postal: Newbridge Networks Corporation
                         600 March Road
                         Kanata, Ontario, Canada K2K 2E6

                         Tel: +1 613 591 3600
                         Fax: +1 613 591 3680

                      E-mail: davef@newbridge.com"
              DESCRIPTION
                   "The MIB module to describe
                    DS3/E3 interfaces objects."

              ::= { transmission 30 }
          -- The DS3/E3 Near End Group

          -- Implementation of this group is mandatory for all
          -- systems that attach to a DS3/E3 Interface.

          -- The DS3/E3 Near End Group consists of four tables:
          --    DS3/E3 Configuration
          --    DS3/E3 Current
          --    DS3/E3 Interval
          --    DS3/E3 Total

          -- the DS3/E3 Configuration

          dsx3ConfigTable OBJECT-TYPE
              SYNTAX  SEQUENCE OF Dsx3ConfigEntry
              MAX-ACCESS  not-accessible
              STATUS  current
              DESCRIPTION
                      "The DS3/E3 Configuration table."
              ::= { ds3 5 }

          dsx3ConfigEntry OBJECT-TYPE
              SYNTAX  Dsx3ConfigEntry
              MAX-ACCESS  not-accessible
              STATUS  current
              DESCRIPTION
                      "An entry in the DS3/E3 Configuration table."
              INDEX   { ifIndex }
              ::= { dsx3ConfigTable 1 }

          Dsx3ConfigEntry ::=
              SEQUENCE {
                  dsx3LineIndex
                      INTEGER,
                  dsx3IfIndex
                      INTEGER,
                  dsx3TimeElapsed
                      INTEGER,
                  dsx3ValidIntervals
                      INTEGER,
                  dsx3LineType
                      INTEGER,
                  dsx3LineCoding
                      INTEGER,
                  dsx3SendCode
                      INTEGER,
                  dsx3CircuitIdentifier
                      DisplayString,
                  dsx3LoopbackConfig
                      INTEGER,
                  dsx3LineStatus
                      INTEGER,
                  dsx3TransmitClockSource
                      INTEGER
          }
                      INTEGER,
                  dsx3InvalidIntervals
                      INTEGER,
                  dsx3LineLength
                      INTEGER,
                  dsx3LineStatusLastChange
                      TimeStamp,
                  dsx3LineStatusChangeTrapEnable
                      INTEGER}

          dsx3LineIndex OBJECT-TYPE
              SYNTAX  INTEGER (1..65535)
              MAX-ACCESS  read-only
              STATUS  deprecated
              DESCRIPTION
                      "This object is the identifier of a DS3/E3
                      Interface on a managed device.  If there is an
                      ifEntry that is directly associated with this and
                      only this DS3/E3 interface, it should have the
                      same value as ifIndex.  Otherwise, number the
                      dsx3LineIndices with an unique identifier
                      following the rules of choosing a number that is
                      greater than ifNumber and numbering the inside
                      interfaces (e.g., equipment side) with even
                      numbers and outside interfaces (e.g, network side)
                      with odd numbers."
              ::= { dsx3ConfigEntry 1 }

          dsx3IfIndex OBJECT-TYPE
              SYNTAX  INTEGER (1..65535)
              MAX-ACCESS  read-only
              STATUS  deprecated
              DESCRIPTION
                      "This value for this object is equal to the value
                      of ifIndex from the Interfaces table of MIB II
                      (RFC 1213)."
              ::= { dsx3ConfigEntry 2 }
          dsx3TimeElapsed OBJECT-TYPE
              SYNTAX  INTEGER (0..899)
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The number of seconds that have elapsed since the
                      beginning of the near end current error-
                      measurement period."
              ::= { dsx3ConfigEntry 3 }

          dsx3ValidIntervals OBJECT-TYPE
              SYNTAX  INTEGER (0..96)
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The number of previous near end intervals for
                      which valid data was collected.  The value will be
                      96 unless the interface was brought online within
                      the last 24 hours, in which case the value will be
                      the number of complete 15 minute near end
                      intervals since the interface has been online.  In
                      the case where the agent is a proxy, it is
                      possible that some intervals are unavailable.  In
                      this case, this interval is the maximum interval
                      number for which valid data is available."
              ::= { dsx3ConfigEntry 4 }

          dsx3LineType OBJECT-TYPE
              SYNTAX  INTEGER {
                          dsx3other(1),
                          dsx3M23(2),
                          dsx3SYNTRAN(3),
                          dsx3CbitParity(4),
                          dsx3ClearChannel(5),
                          e3other(6),
                          e3Framed(7),
                          e3Plcp(8)
                      }
              MAX-ACCESS  read-write
              STATUS  current
              DESCRIPTION
                      "This variable indicates the variety of DS3 C-bit
                      or E3 application implementing this interface. The
                      type of interface affects the interpretation of
                      the usage and error statistics.  The rate of DS3
                      is 44.736 Mbps and E3 is 34.368 Mbps.  The
                      dsx3ClearChannel value means that the C-bits are
                      not used except for sending/receiving AIS.
                      The values, in sequence, describe:

                      TITLE:            SPECIFICATION:
                      dsx3M23            ANSI T1.107-1988 [11] [9]
                      dsx3SYNTRAN        ANSI T1.107-1988 [11] [9]
                      dsx3CbitParity     ANSI T1.107a-1990 [11a] [9a]
                      dsx3ClearChannel   ANSI T1.102-1987 [10] [8]
                      e3Framed           CCITT G.751 [14] [12]
                      e3Plcp             ETSI T/NA(91)18 [15]." [13]."
              ::= { dsx3ConfigEntry 5 }

          dsx3LineCoding OBJECT-TYPE
              SYNTAX  INTEGER {
                          dsx3Other(1),
                          dsx3B3ZS(2),
                          e3HDB3(3)
                      }
              MAX-ACCESS  read-write
              STATUS  current
              DESCRIPTION
                      "This variable describes the variety of Zero Code
                      Suppression used on this interface, which in turn
                      affects a number of its characteristics.

                      dsx3B3ZS and e3HDB3 refer to the use of specified
                      patterns of normal bits and bipolar violations
                      which are used to replace sequences of zero bits
                      of a specified length."
              ::= { dsx3ConfigEntry 6 }

          dsx3SendCode OBJECT-TYPE
                 SYNTAX  INTEGER {
                         dsx3SendNoCode(1),
                         dsx3SendLineCode(2),
                         dsx3SendPayloadCode(3),
                         dsx3SendResetCode(4),
                         dsx3SendDS1LoopCode(5),
                         dsx3SendTestPattern(6)
                         }
                 MAX-ACCESS  read-write
                 STATUS  current
                 DESCRIPTION
                      "This variable indicates what type of code is
                      being sent across the DS3/E3 interface by the
                      device.  (These are optional for E3 interfaces.)
                      Setting this variable causes the interface to
                      begin sending the code requested.
                      The values mean:

                         dsx3SendNoCode
                             sending looped or normal data

                         dsx3SendLineCode
                             sending a request for a line loopback

                         dsx3SendPayloadCode
                             sending a request for a payload loopback
                             (i.e., all DS1/E1s in a DS3/E3 frame)

                         dsx3SendResetCode
                             sending a loopback deactivation request

                         dsx3SendDS1LoopCode
                             requesting to loopback a particular DS1/E1
                             within a DS3/E3 frame

                         dsx3SendTestPattern
                             sending a test pattern."
                 ::= { dsx3ConfigEntry 7 }

          dsx3CircuitIdentifier OBJECT-TYPE
              SYNTAX  DisplayString (SIZE (0..255))
              MAX-ACCESS  read-write
              STATUS  current
              DESCRIPTION
                      "This variable contains the transmission vendor's
                      circuit identifier, for the purpose of
                      facilitating troubleshooting."
              ::= { dsx3ConfigEntry 8 }

          dsx3LoopbackConfig OBJECT-TYPE
                 SYNTAX  INTEGER {
                           dsx3NoLoop(1),
                           dsx3PayloadLoop(2),
                           dsx3LineLoop(3),
                           dsx3OtherLoop(4),
                           dsx3InwardLoop(5)
                         }
                 MAX-ACCESS  read-write
                 STATUS  current
                 DESCRIPTION
                    "This variable represents the loopback configuration
                    of the DS3/E3 interface.
                    The values mean:

                    dsx3NoLoop
                      Not in the loopback state.  A device that is
                      not capable of performing a loopback on
                      the interface shall always return this as
                      it's value.

                    dsx3PayloadLoop
                      The received signal at this interface is looped
                      through the device.  Typically the received signal
                      is looped back for retransmission after it has
                      passed through the device's framing function.

                    dsx3LineLoop
                      The received signal at this interface does not
                      go through the device (minimum penetration) but
                      is looped back out.

                    dsx3OtherLoop
                      Loopbacks that are not defined here.

                    dsx3InwardLoop
                      The sent signal at this interface is looped back
                      through the device."
                 ::= { dsx3ConfigEntry 9 }

          dsx3LineStatus OBJECT-TYPE
              SYNTAX  INTEGER (1..1023) (1..4095)
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                 "This variable indicates the
                 Line Status of the interface.
                 It contains loopback state information
                 and failure state information.
                 The dsx3LineStatus is a bit map represented
                 as a sum, therefore,
                 it can represent multiple failures
                 and a loopback (see dsx3LoopbackConfig object
                 for the type of loopback)
                 simultaneously.
                 The dsx3NoAlarm should be set if and only if
                 no other flag is set.

                 If the dsx3loopbackState bit is set, the loopback in ef-
                 fect can be determined from the dsx3loopbackConfig object.

                 The various bit positions are:
                    1     dsx3NoAlarm         No alarm present
                    2     dsx3RcvRAIFailure   Receiving Yellow/Remote
                                              Alarm Indication
                    4     dsx3XmitRAIAlarm    Transmitting Yellow/Remote
                                              Alarm Indication
                    8     dsx3RcvAIS          Receiving AIS failure state
                   16     dsx3XmitAIS         Transmitting AIS
                   32     dsx3LOF             Receiving LOF failure state
                   64     dsx3LOS             Receiving LOS failure state
                  128     dsx3LoopbackState   Looping the received signal
                  256     dsx3RcvTestCode     Receiving a Test Pattern
                  512     dsx3OtherFailure    any line status not defined
                                            here"
                                              here
                 1024     dsx3UnavailSigState Near End in Unavailable Signal
                                              State
                 2048     dsx3NetEquipOOS     Carrier Equipment Out of Service"
              ::= { dsx3ConfigEntry 10 }

          dsx3TransmitClockSource OBJECT-TYPE
              SYNTAX  INTEGER {
                          loopTiming(1),
                          localTiming(2),
                          throughTiming(3)
                      }
              MAX-ACCESS  read-write
              STATUS  current
              DESCRIPTION
                 "The source of Transmit Clock.  transmit clock, is
                 derived from the recovered receive clock of another DS3
                 interface."
             ::= { dsx3ConfigEntry 11 }
         -- the DS3/E3 Current

         -- The DS3/E3 current table contains various statistics being
         -- collected for the current 15 minute interval

         dsx3CurrentTable

         dsx3InvalidIntervals OBJECT-TYPE
             SYNTAX  SEQUENCE OF Dsx3CurrentEntry  INTEGER (0..96)
             MAX-ACCESS  not-accessible  read-only
             STATUS  current
             DESCRIPTION
                     "The DS3/E3 Current table." number of intervals for which no valid data is
                      available."
              ::= { ds3 6 dsx3ConfigEntry 12 }

          dsx3CurrentEntry

          dsx3LineLength OBJECT-TYPE
              SYNTAX  Dsx3CurrentEntry  INTEGER (0..64000)
              MAX-ACCESS  not-accessible  read-only
              STATUS  current
              DESCRIPTION
                      "An entry in
                      "The length of the DS3/E3 Current table."
              INDEX   { dsx3CurrentIndex } ds3 line in meters."
              ::= { dsx3CurrentTable 1 dsx3ConfigEntry 13 }

          Dsx3CurrentEntry ::=
              SEQUENCE {
                  dsx3CurrentIndex
                      INTEGER,
                  dsx3CurrentPESs
                      Gauge32,
                  dsx3CurrentPSESs
                      Gauge32,
                  dsx3CurrentSEFSs
                      Gauge32,
                  dsx3CurrentUASs
                      Gauge32,
                  dsx3CurrentLCVs
                      Gauge32,
                  dsx3CurrentPCVs
                      Gauge32,
                  dsx3CurrentLESs
                      Gauge32,
                  dsx3CurrentCCVs
                      Gauge32,
                  dsx3CurrentCESs
                      Gauge32,
                  dsx3CurrentCSESs
                      Gauge32

          dsx3LineStatusLastChange OBJECT-TYPE
               SYNTAX  TimeStamp
               MAX-ACCESS  read-only
               STATUS  current
               DESCRIPTION
                                   "The value of MIB II's sysUpTime
                      object at the
                                   time this DS3/E3 entered its current
                                   line status state.
                                   If the current state was entered
                      prior to the last
                                   re-initialization of the proxy-agent,
                      then this
                                   object contains a zero value."
               ::= { dsx3ConfigEntry 14 }

          dsx3LineStatusChangeTrapEnable  OBJECT-TYPE
              SYNTAX      INTEGER { enabled(1),
                                    disabled(2) }
              MAX-ACCESS  read-write
              STATUS      current
              DESCRIPTION
                      "Indicates whether dsx3LineStatusChange traps
                      should be generated for this interface.  By
                      default, this object should have the value
                      disabled(2)."
             ::= { dsx3ConfigEntry 15 }
          -- the DS3/E3 Current Table

          -- The DS3/E3 current table contains various statistics being
          -- collected for the current 15 minute interval

          dsx3CurrentTable OBJECT-TYPE
              SYNTAX  SEQUENCE OF Dsx3CurrentEntry
              MAX-ACCESS  not-accessible
              STATUS  current
              DESCRIPTION
                      "The DS3/E3 Current table."
              ::= { ds3 6 }

          dsx3CurrentEntry OBJECT-TYPE
              SYNTAX  Dsx3CurrentEntry
              MAX-ACCESS  not-accessible
              STATUS  current
              DESCRIPTION
                      "An entry in the DS3/E3 Current table."
              INDEX   { dsx3CurrentIndex }
              ::= { dsx3CurrentTable 1 }

          Dsx3CurrentEntry ::=
              SEQUENCE {
                  dsx3CurrentIndex
                      INTEGER,
                  dsx3CurrentPESs
                      Gauge32,
                  dsx3CurrentPSESs
                      Gauge32,
                  dsx3CurrentSEFSs
                      Gauge32,
                  dsx3CurrentUASs
                      Gauge32,
                  dsx3CurrentLCVs
                      Gauge32,
                  dsx3CurrentPCVs
                      Gauge32,
                  dsx3CurrentLESs
                      Gauge32,
                  dsx3CurrentCCVs
                      Gauge32,
                  dsx3CurrentCESs
                      Gauge32,
                  dsx3CurrentCSESs
                      Gauge32
              }

          dsx3CurrentIndex OBJECT-TYPE
              SYNTAX  INTEGER (1..65535)
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The index value which uniquely identifies the
                      DS3/E3 interface to which this entry is
                      applicable.  The interface identified by a
                      particular value of this index is the same
                      interface as identified by the same value an
                      dsx3LineIndex object instance."
              ::= { dsx3CurrentEntry 1 }

          dsx3CurrentPESs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of P-bit
                      Errored Seconds, encountered by a DS3 interface in
                      the current 15 minute interval." interval.  noSuchInstance
                      will be returned if no data is available."
              ::= { dsx3CurrentEntry 2 }

          dsx3CurrentPSESs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of P-bit
                      Severely Errored Seconds, encountered by a DS3
                      interface in the current 15 minute interval." interval.
                      noSuchInstance will be returned if no data is
                      available."
              ::= { dsx3CurrentEntry 3 }

          dsx3CurrentSEFSs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of
                      Severely Errored Framing Seconds, encountered by a
                      DS3/E3 interface in the current 15 minute
                      interval."
                      interval.  noSuchInstance will be returned if no
                      data is available."
              ::= { dsx3CurrentEntry 4 }

          dsx3CurrentUASs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of
                      Unavailable Seconds, encountered by a DS3
                      interface in the current 15 minute interval." interval.
                      noSuchInstance will be returned if no data is
                      available."
              ::= { dsx3CurrentEntry 5 }

          dsx3CurrentLCVs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of Line
                      Coding Violations encountered by a DS3/E3
                      interface in the current 15 minute interval." interval.
                      noSuchInstance will be returned if no data is
                      available."
              ::= { dsx3CurrentEntry 6 }

          dsx3CurrentPCVs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of P-bit
                      Coding Violations, encountered by a DS3 interface
                      in the current 15 minute interval." interval.  noSuchInstance
                      will be returned if no data is available."
              ::= { dsx3CurrentEntry 7 }

          dsx3CurrentLESs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The number of Line Errored Seconds encountered by
                      a DS3/E3 interface in the current 15 minute
                      interval."
                      interval.  noSuchInstance will be returned if no
                      data is available."
              ::= { dsx3CurrentEntry 8 }

          dsx3CurrentCCVs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The number of C-bit Coding Violations encountered
                      by a DS3 interface in the current 15 minute
                      interval."
                      interval.  noSuchInstance will be returned if no
                      data is available."
              ::= { dsx3CurrentEntry 9 }

          dsx3CurrentCESs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The number of C-bit Errored Seconds encountered
                      by a DS3 interface in the current 15 minute
                      interval."
                      interval.  noSuchInstance will be returned if no
                      data is available."
              ::= { dsx3CurrentEntry 10 }

          dsx3CurrentCSESs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The number of C-bit Severely Errored Seconds
                      encountered by a DS3 interface in the current 15
                      minute interval." interval.  noSuchInstance will be returned
                      if no data is available."
              ::= { dsx3CurrentEntry 11 }
          -- the DS3/E3 Interval Table

          -- The DS3/E3 Interval Table contains various statistics
          -- collected by each DS3/E3 Interface over the previous
          -- 24 hours of operation.  The past 24 hours are broken
          -- into 96 completed 15 minute intervals.

          dsx3IntervalTable OBJECT-TYPE
              SYNTAX  SEQUENCE OF Dsx3IntervalEntry
              MAX-ACCESS  not-accessible
              STATUS  current
              DESCRIPTION
                      "The DS3/E3 Interval table."
              ::= { ds3 7 }

          dsx3IntervalEntry OBJECT-TYPE
              SYNTAX  Dsx3IntervalEntry
              MAX-ACCESS  not-accessible
              STATUS  current
              DESCRIPTION
                      "An entry in the DS3/E3 Interval table."
              INDEX   { dsx3IntervalIndex, dsx3IntervalNumber }
              ::= { dsx3IntervalTable 1 }

          Dsx3IntervalEntry ::=
              SEQUENCE {
                  dsx3IntervalIndex
                      INTEGER,
                  dsx3IntervalNumber
                      INTEGER,
                  dsx3IntervalPESs
                      Gauge32,
                  dsx3IntervalPSESs
                      Gauge32,
                  dsx3IntervalSEFSs
                      Gauge32,
                  dsx3IntervalUASs
                      Gauge32,
                  dsx3IntervalLCVs
                      Gauge32,
                  dsx3IntervalPCVs
                      Gauge32,
                  dsx3IntervalLESs
                      Gauge32,
                  dsx3IntervalCCVs
                      Gauge32,
                  dsx3IntervalCESs
                      Gauge32,
                  dsx3IntervalCSESs
                      Gauge32
              }
                      Gauge32,
                  dsx3IntervalValidData
                      INTEGER
              }

          dsx3IntervalIndex OBJECT-TYPE
              SYNTAX  INTEGER (1..65535)
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The index value which uniquely identifies the
                      DS3/E3 interface to which this entry is
                      applicable.  The interface identified by a
                      particular value of this index is the same
                      interface as identified by the same value an
                      dsx3LineIndex object instance."
              ::= { dsx3IntervalEntry 1 }

          dsx3IntervalNumber OBJECT-TYPE
              SYNTAX  INTEGER (1..96)
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "A number between 1 and 96, where 1 is the most
                      recently completed 15 minute interval and 96 is
                      the least recently completed 15 minutes interval
                      (assuming that all 96 intervals are valid)." completed 23 hours and 45
                      minutes prior to interval 1."
              ::= { dsx3IntervalEntry 2 }

          dsx3IntervalPESs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of P-bit
                      Errored Seconds, encountered by a DS3 interface in
                      one of the previous 96, individual 15 minute,
                      intervals. In the case where the agent is a proxy
                      and valid data is not available, return
                      noSuchName."
                      noSuchInstance."
              ::= { dsx3IntervalEntry 3 }
          dsx3IntervalPSESs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of P-bit
                      Severely Errored Seconds, encountered by a DS3
                      interface in one of the previous 96, individual 15
                      minute, intervals. In the case where the agent is
                      a proxy and valid data is not available, return
                      noSuchName."
                      noSuchInstance."
              ::= { dsx3IntervalEntry 4 }

          dsx3IntervalSEFSs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of
                      Severely Errored Framing Seconds, encountered by a
                      DS3/E3 interface in one of the previous 96,
                      individual 15 minute, intervals. In the case where
                      the agent is a proxy and valid data is not
                      available, return noSuchName." noSuchInstance."
              ::= { dsx3IntervalEntry 5 }

          dsx3IntervalUASs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of
                      Unavailable Seconds, encountered by a DS3
                      interface in one of the previous 96, individual 15
                      minute, intervals. In the case where the agent is
                      a proxy and valid data is not available, return
                      noSuchName.
                      noSuchInstance. This object may decrease if the
                      occurance of unavailable seconds occurs across an
                      inteval boundary."
              ::= { dsx3IntervalEntry 6 }

          dsx3IntervalLCVs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of Line
                      Coding Violations encountered by a DS3/E3
                      interface in one of the previous 96, individual 15
                      minute, intervals. In the case where the agent is
                      a proxy and valid data is not available, return
                      noSuchName."
                      noSuchInstance."
              ::= { dsx3IntervalEntry 7 }

          dsx3IntervalPCVs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of P-bit
                      Coding Violations, encountered by a DS3 interface
                      in one of the previous 96, individual 15 minute,
                      intervals. In the case where the agent is a proxy
                      and valid data is not available, return
                      noSuchName."
                      noSuchInstance."
              ::= { dsx3IntervalEntry 8 }

          dsx3IntervalLESs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The number of Line Errored  Seconds  (BPVs  or
                      illegal  zero  sequences) encountered by a DS3/E3
                      interface in one of the previous 96, individual 15
                      minute, intervals. In the case where the agent is
                      a proxy and valid data is not available, return noSuchName."
                      noSuchInstance."
              ::= { dsx3IntervalEntry 9 }

          dsx3IntervalCCVs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The number of C-bit Coding Violations encountered
                      by a DS3 interface in one of the previous 96,
                      individual 15 minute, intervals. In the case where
                      the agent is a proxy and valid data is not
                      available, return noSuchName." noSuchInstance."
              ::= { dsx3IntervalEntry 10 }

          dsx3IntervalCESs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The number of C-bit Errored Seconds encountered
                      by a DS3 interface in one of the previous 96,
                      individual 15 minute, intervals. In the case where
                      the agent is a proxy and valid data is not
                      available, return noSuchName." noSuchInstance."
              ::= { dsx3IntervalEntry 11 }

          dsx3IntervalCSESs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The number of C-bit Severely Errored Seconds
                      encountered by a DS3 interface in one of the
                      previous 96, individual 15 minute, intervals. In
                      the case where the agent is a proxy and valid data
                      is not available, return noSuchName." noSuchInstance."
              ::= { dsx3IntervalEntry 12 }

          dsx3IntervalValidData OBJECT-TYPE
              SYNTAX  INTEGER {
                          true(1),
                          false(2)
                      }
              MAX-ACCESS read-only
              STATUS current
              DESCRIPTION
                      "This variable indicates if there is valid data
                      for this interval.  A value of true(1) indicates
                      the data is valid."
              ::= {dsx3IntervalEntry 13 }
          -- the DS3/E3 Total

          -- The DS3/E3 Total Table contains the cumulative sum of the
          -- various statistics for the 24 hour period preceding the
          -- current interval.

          dsx3TotalTable OBJECT-TYPE
              SYNTAX  SEQUENCE OF Dsx3TotalEntry
              MAX-ACCESS  not-accessible
              STATUS  current
              DESCRIPTION
                      "The DS3/E3 Total table.  24 hour interval."
              ::= { ds3 8 }

          dsx3TotalEntry OBJECT-TYPE
              SYNTAX  Dsx3TotalEntry
              MAX-ACCESS  not-accessible
              STATUS  current
              DESCRIPTION
                      "An entry in the DS3/E3 Total table."
              INDEX   { dsx3TotalIndex }
              ::= { dsx3TotalTable 1 }

          Dsx3TotalEntry ::=
              SEQUENCE {
                  dsx3TotalIndex
                      INTEGER,
                  dsx3TotalPESs
                      Gauge32,
                  dsx3TotalPSESs
                      Gauge32,
                  dsx3TotalSEFSs
                      Gauge32,
                  dsx3TotalUASs
                      Gauge32,
                  dsx3TotalLCVs
                      Gauge32,
                  dsx3TotalPCVs
                      Gauge32,
                  dsx3TotalLESs
                      Gauge32,
                  dsx3TotalCCVs
                      Gauge32,
                  dsx3TotalCESs
                      Gauge32,
                  dsx3TotalCSESs
                      Gauge32
              }

          dsx3TotalIndex OBJECT-TYPE
              SYNTAX  INTEGER (1..65535)
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The index value which uniquely identifies the
                      DS3/E3 interface to which this entry is
                      applicable.  The interface identified by a
                      particular value of this index is the same
                      interface as identified by the same value an
                      dsx3LineIndex object instance."
              ::= { dsx3TotalEntry 1 }

          dsx3TotalPESs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of P-bit
                      Errored Seconds, encountered by a DS3 interface in
                      the previous 24 hour interval" interval. Invalid 15 minute
                      intervals count as 0."
              ::= { dsx3TotalEntry 2 }

          dsx3TotalPSESs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of P-bit
                      Severely Errored Seconds, encountered by a DS3
                      interface in the previous 24 hour interval." interval.
                      Invalid 15 minute intervals count as 0."
              ::= { dsx3TotalEntry 3 }

          dsx3TotalSEFSs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of
                      Severely Errored Framing Seconds, encountered by a
                      DS3/E3 interface in the previous 24 hour
                      interval." interval.
                      Invalid 15 minute intervals count as 0."
              ::= { dsx3TotalEntry 4 }

          dsx3TotalUASs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of
                      Unavailable Seconds, encountered by a DS3
                      interface in the previous 24 hour interval." interval.
                      Invalid 15 minute intervals count as 0."
              ::= { dsx3TotalEntry 5 }

          dsx3TotalLCVs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of Line
                      Coding Violations encountered by a DS3/E3
                      interface in the previous 24 hour interval." interval.
                      Invalid 15 minute intervals count as 0."
              ::= { dsx3TotalEntry 6 }

          dsx3TotalPCVs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of P-bit
                      Coding Violations, encountered by a DS3 interface
                      in the previous 24 hour interval." interval. Invalid 15
                      minute intervals count as 0."
              ::= { dsx3TotalEntry 7 }

          dsx3TotalLESs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The number of Line Errored  Seconds  (BPVs  or
                      illegal  zero  sequences) encountered by a DS3/E3
                      interface in the previous 24 hour interval." interval.
                      Invalid 15 minute intervals count as 0."
              ::= { dsx3TotalEntry 8 }

          dsx3TotalCCVs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The number of C-bit Coding Violations encountered
                      by a DS3 interface in the previous 24 hour
                      interval."
                      interval. Invalid 15 minute intervals count as 0."
              ::= { dsx3TotalEntry 9 }

          dsx3TotalCESs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The number of C-bit Errored Seconds encountered
                      by a DS3 interface in the previous 24 hour
                      interval."
                      interval. Invalid 15 minute intervals count as 0."
              ::= { dsx3TotalEntry 10 }

          dsx3TotalCSESs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The number of C-bit Severely Errored Seconds
                      encountered by a DS3 interface in the previous 24
                      hour interval." interval. Invalid 15 minute intervals count
                      as 0."
              ::= { dsx3TotalEntry 11 }
          -- The DS3 Far End Group

          -- Implementation of this group is optional for all systems
          -- that attach to a DS3 Interface.
          -- However, only C-bit Parity and SYNTRAN DS3 applications
          -- have the capability (option) of providing this information.

          -- The DS3 Far End Group consists of four tables:
          --   DS3 Far End Configuration
          --   DS3 Far End Current
          --   DS3 Far End Interval
          --   DS3 Far End Total

          -- The DS3 Far End Configuration Table contains
          -- configuration information
          -- reported in the C-bits from the remote end.

          dsx3FarEndConfigTable OBJECT-TYPE
              SYNTAX  SEQUENCE OF Dsx3FarEndConfigEntry
              MAX-ACCESS  not-accessible
              STATUS  current
              DESCRIPTION
                      "The DS3 Far End Configuration table."
              ::= { ds3 9 }

          dsx3FarEndConfigEntry OBJECT-TYPE
              SYNTAX  Dsx3FarEndConfigEntry
              MAX-ACCESS  not-accessible
              STATUS  current
              DESCRIPTION
                      "An entry in the DS3 Far End Configuration table."
              INDEX   { dsx3FarEndLineIndex }
              ::= { dsx3FarEndConfigTable 1 }

          Dsx3FarEndConfigEntry ::=
              SEQUENCE {
                  dsx3FarEndLineIndex
                      INTEGER,
                  dsx3FarEndEquipCode
                      DisplayString,
                  dsx3FarEndLocationIDCode
                      DisplayString,
                  dsx3FarEndFrameIDCode
                      DisplayString,
                  dsx3FarEndUnitCode
                      DisplayString,
                  dsx3FarEndFacilityIDCode
                      DisplayString
               }

          dsx3FarEndLineIndex OBJECT-TYPE
              SYNTAX  INTEGER (1..65535)
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The index value which uniquely identifies the DS3
                      interface to which this entry is applicable.  The
                      interface identified by a particular value of this
                      index is the same interface as identified by the
                      same value an dsx3LineIndex object instance."
             ::= { dsx3FarEndConfigEntry 1 }

          dsx3FarEndEquipCode OBJECT-TYPE
              SYNTAX  DisplayString (SIZE (0..10))
              MAX-ACCESS  read-write
              STATUS  current
              DESCRIPTION
                      "This is the Far End Equipment Identification code
                      that describes the specific piece of equipment.
                      It is sent within the Path Identification
                      Message."
              ::= { dsx3FarEndConfigEntry 2 }

          dsx3FarEndLocationIDCode OBJECT-TYPE
              SYNTAX  DisplayString (SIZE (0..11))
              MAX-ACCESS  read-write
              STATUS  current
              DESCRIPTION
                      "This is the Far End Location Identification code
                      that describes the specific location of the
                      equipment.  It is sent within the Path
                      Identification Message."
              ::= { dsx3FarEndConfigEntry 3 }

          dsx3FarEndFrameIDCode OBJECT-TYPE
              SYNTAX  DisplayString (SIZE (0..10))
              MAX-ACCESS  read-write
              STATUS  current
              DESCRIPTION
                      "This is the Far End Frame Identification code
                      that identifies where the equipment is located
                      within a building at a given location.  It is sent
                      within the Path Identification Message."
              ::= { dsx3FarEndConfigEntry 4 }

          dsx3FarEndUnitCode OBJECT-TYPE
              SYNTAX  DisplayString (SIZE (0..6))
              MAX-ACCESS  read-write
              STATUS  current
              DESCRIPTION
                      "This is the Far End code that identifies the
                      equipment location within a bay.  It is sent
                      within the Path Identification Message."
              ::= { dsx3FarEndConfigEntry 5 }

          dsx3FarEndFacilityIDCode OBJECT-TYPE
              SYNTAX  DisplayString (SIZE (0..38))
              MAX-ACCESS  read-write
              STATUS  current
              DESCRIPTION
                      "This code identifies a specific Far End DS3 path.
                      It is sent within the Path Identification
                      Message."
              ::= { dsx3FarEndConfigEntry 6 }

          -- The DS3 Far End Current

          -- The DS3 Far End Current table contains various statistics
          -- being collected for the current 15 minute interval.
          -- The statistics are collected from the far end block error
          -- code within the C-bits.

          dsx3FarEndCurrentTable OBJECT-TYPE
              SYNTAX  SEQUENCE OF Dsx3FarEndCurrentEntry
              MAX-ACCESS  not-accessible
              STATUS  current
              DESCRIPTION
                      "The DS3 Far End Current table."
              ::= { ds3 10 }

          dsx3FarEndCurrentEntry OBJECT-TYPE
              SYNTAX  Dsx3FarEndCurrentEntry
              MAX-ACCESS  not-accessible
              STATUS  current
              DESCRIPTION
                      "An entry in the DS3 Far End Current table."
              INDEX   { dsx3FarEndCurrentIndex }
              ::= { dsx3FarEndCurrentTable 1 }

          Dsx3FarEndCurrentEntry ::=
              SEQUENCE {
                  dsx3FarEndCurrentIndex
                      INTEGER,
                  dsx3FarEndTimeElapsed
                      INTEGER,
                  dsx3FarEndValidIntervals
                      INTEGER,
                  dsx3FarEndCurrentCESs
                      Gauge32,
                  dsx3FarEndCurrentCSESs
                      Gauge32,
                  dsx3FarEndCurrentCCVs
                      Gauge32,
                  dsx3FarEndCurrentUASs
                      Gauge32
                      Gauge32,
                  dsx3FarEndInvalidIntervals
                      INTEGER
              }

           dsx3FarEndCurrentIndex OBJECT-TYPE
              SYNTAX  INTEGER (1..65535)
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The index value which uniquely identifies the DS3
                      interface to which this entry is applicable.  The
                      interface identified by a particular value of this
                      index is the same interface as identified by the
                      same value an dsx3LineIndex object instance."
              ::= { dsx3FarEndCurrentEntry 1 }

          dsx3FarEndTimeElapsed OBJECT-TYPE
              SYNTAX  INTEGER (0..899)
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The number of seconds that have elapsed since the
                      beginning of the far end current error-measurement
                      period."
              ::= { dsx3FarEndCurrentEntry 2 }

          dsx3FarEndValidIntervals OBJECT-TYPE
              SYNTAX  INTEGER (0..96)
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The number of previous far end intervals for
                      which valid data was collected.  The value will be
                      96 unless the interface was brought online within
                      the last 24 hours, in which case the value will be
                      the number of complete 15 minute far end intervals
                      since the interface has been online."
              ::= { dsx3FarEndCurrentEntry 3 }

          dsx3FarEndCurrentCESs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of Far Far
                      End C-bit Errored Seconds encountered by a DS3
                      interface in the current 15 minute interval." interval.
                      noSuchInstance will be returned if no data is
                      available."
              ::= { dsx3FarEndCurrentEntry 4 }

          dsx3FarEndCurrentCSESs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of Far End
                      C-bit Severely Errored Seconds encountered by a
                      DS3 interface in the current 15 minute interval." interval.
                      noSuchInstance will be returned if no data is
                      available."
              ::= { dsx3FarEndCurrentEntry 5 }

          dsx3FarEndCurrentCCVs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of Far End
                      C-bit Coding Violations reported via the far end
                      block error count encountered by a DS3 interface
                      in the current 15 minute interval." interval.  noSuchInstance
                      will be returned if no data is available."
              ::= { dsx3FarEndCurrentEntry 6 }

          dsx3FarEndCurrentUASs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of Far End
                      unavailable seconds encountered by a DS3 interface
                      in the current 15 minute interval." interval.  noSuchInstance
                      will be returned if no data is available."
              ::= { dsx3FarEndCurrentEntry 7 }

          dsx3FarEndInvalidIntervals OBJECT-TYPE
              SYNTAX  INTEGER (0..96)
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The number of intervals for which no valid data
                      is available."
              ::= { dsx3FarEndCurrentEntry 8 }

          -- The DS3 Far End Interval Table

          -- The DS3 Far End Interval Table contains various statistics
          -- collected by each DS3 interface over the previous 24
          -- hours of operation.  The past 24 hours are broken into 96
          -- completed 15 minute intervals.

          dsx3FarEndIntervalTable OBJECT-TYPE
              SYNTAX  SEQUENCE OF Dsx3FarEndIntervalEntry
              MAX-ACCESS  not-accessible
              STATUS  current
              DESCRIPTION
                     "The DS3 Far End Interval table."
              ::= { ds3 11 }

          dsx3FarEndIntervalEntry OBJECT-TYPE
              SYNTAX  Dsx3FarEndIntervalEntry
              MAX-ACCESS  not-accessible
              STATUS  current
              DESCRIPTION
                      "An entry in the DS3 Far End Interval table."
              INDEX   { dsx3FarEndIntervalIndex,
                        dsx3FarEndIntervalNumber }
              ::= { dsx3FarEndIntervalTable 1 }

          Dsx3FarEndIntervalEntry ::=
              SEQUENCE {
                   dsx3FarEndIntervalIndex
                        INTEGER,
                   dsx3FarEndIntervalNumber
                        INTEGER,
                   dsx3FarEndIntervalCESs
                        Gauge32,
                   dsx3FarEndIntervalCSESs
                        Gauge32,
                   dsx3FarEndIntervalCCVs
                        Gauge32,
                   dsx3FarEndIntervalUASs
                        Gauge32
              }

          dsx3FarEndIntervalIndex OBJECT-TYPE
              SYNTAX  INTEGER (1..65535)
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The index value which uniquely identifies the DS3
                      interface to which this entry is applicable.  The
                      interface identified by a particular value of this
                      index is the same interface as identified by the
                      same value an dsx3LineIndex object instance."
              ::= { dsx3FarEndIntervalEntry 1 }

          dsx3FarEndIntervalNumber OBJECT-TYPE
             SYNTAX  INTEGER (1..96)
             MAX-ACCESS  read-only
             STATUS  current
             DESCRIPTION
                      "A number between 1 and 96, where 1 is the most
                      recently completed 15 minute interval and 96 is
                      the least recently completed 15 minutes interval (assuming that all 96 intervals are
                    valid)." completed 23 hours and 45
                      minutes prior to interval 1."
             ::= { dsx3FarEndIntervalEntry 2 }
          dsx3FarEndIntervalCESs OBJECT-TYPE
             SYNTAX  Gauge32
             MAX-ACCESS  read-only
             STATUS  current
             DESCRIPTION
                      "The counter associated with the number of Far End
                      C-bit Errored Seconds encountered by a DS3
                      interface in one of the previous 96, individual 15
                      minute, intervals." intervals. In the case where the agent is
                      a proxy and valid data is not available, return
                      noSuchInstance."
            ::= { dsx3FarEndIntervalEntry 3 }

          dsx3FarEndIntervalCSESs OBJECT-TYPE
             SYNTAX  Gauge32
             MAX-ACCESS  read-only
             STATUS  current
             DESCRIPTION
                      "The counter associated with the number of Far End
                      C-bit Severely Errored Seconds encountered by a
                      DS3 interface in one of the previous 96,
                      individual 15 minute, intervals." intervals. In the case where
                      the agent is a proxy and valid data is not
                      available, return noSuchInstance."
            ::= { dsx3FarEndIntervalEntry 4 }

          dsx3FarEndIntervalCCVs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of Far End
                      C-bit Coding Violations reported via the far end
                      block error count encountered by a DS3 interface
                      in one of the previous 96, individual 15 minute, intervals."
                      intervals. In the case where the agent is a proxy
                      and valid data is not available, return
                      noSuchInstance."
              ::= { dsx3FarEndIntervalEntry 5 }

          dsx3FarEndIntervalUASs OBJECT-TYPE
              SYNTAX  Gauge32
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The counter associated with the number of Far End
                      unavailable seconds encountered by a DS3 interface
                      in one of the previous 96, individual 15 minute, intervals."
              ::= { dsx3FarEndIntervalEntry 6 }

          -- The DS3 Far
                      intervals. In the case where the agent is a proxy
                      and valid data is not available, return
                      noSuchInstance."
              ::= { dsx3FarEndIntervalEntry 6 }

          -- The DS3 Far End Total

          -- The DS3 Far End Total Table contains the cumulative sum
          -- of the various statistics for the 24 hour period preceding
          -- the current interval.

          dsx3FarEndTotalTable OBJECT-TYPE
              SYNTAX  SEQUENCE OF Dsx3FarEndTotalEntry
              MAX-ACCESS  not-accessible
              STATUS  current
              DESCRIPTION
                      "The DS3 Far End Total table.  24 hour interval."
              ::= { ds3 12 }

          dsx3FarEndTotalEntry OBJECT-TYPE
              SYNTAX  Dsx3FarEndTotalEntry
              MAX-ACCESS  not-accessible
              STATUS  current
              DESCRIPTION
                      "An entry in the DS3 Far End Total table."
              INDEX   { dsx3FarEndTotalIndex }
              ::= { dsx3FarEndTotalTable 1 }

          Dsx3FarEndTotalEntry ::=
              SEQUENCE {
                  dsx3FarEndTotalIndex
                      INTEGER,
                  dsx3FarEndTotalCESs
                      Gauge32,
                  dsx3FarEndTotalCSESs
                      Gauge32,
                  dsx3FarEndTotalCCVs
                      Gauge32,
                  dsx3FarEndTotalUASs
                      Gauge32
              }
          dsx3FarEndTotalIndex OBJECT-TYPE
              SYNTAX  INTEGER (1..65535)
              MAX-ACCESS  read-only
              STATUS  current
              DESCRIPTION
                      "The index value which uniquely identifies the DS3
                      interface to which this entry is applicable.  The
                      interface identified by a particular value of this
                      index is the same interface as identified by the
                      same value an dsx3LineIndex object instance."
              ::= { dsx3FarEndTotalEntry 1 }

          dsx3FarEndTotalCESs OBJECT-TYPE
             SYNTAX  Gauge32
             MAX-ACCESS  read-only
             STATUS  current
             DESCRIPTION
                      "The counter associated with the number of Far End
                      C-bit Errored Seconds encountered by a DS3
                      interface in the previous 24 hour interval." interval.
                      Invalid 15 minute intervals count as 0."
             ::= { dsx3FarEndTotalEntry 2 }

          dsx3FarEndTotalCSESs OBJECT-TYPE
             SYNTAX  Gauge32
             MAX-ACCESS  read-only
             STATUS  current
             DESCRIPTION
                      "The counter associated with the number of Far End
                      C-bit Severely Errored Seconds encountered by a
                      DS3 interface in the previous 24 hour interval." interval.
                      Invalid 15 minute intervals count as 0."
             ::= { dsx3FarEndTotalEntry 3 }

          dsx3FarEndTotalCCVs OBJECT-TYPE
             SYNTAX  Gauge32
             MAX-ACCESS  read-only
             STATUS  current
             DESCRIPTION
                      "The counter associated with the number of Far End
                      C-bit Coding Violations reported via the far end
                      block error count encountered by a DS3 interface
                      in the previous 24 hour interval." interval. Invalid 15
                      minute intervals count as 0."
             ::= { dsx3FarEndTotalEntry 4 }
          dsx3FarEndTotalUASs OBJECT-TYPE
             SYNTAX  Gauge32
             MAX-ACCESS  read-only
             STATUS  current
             DESCRIPTION
                      "The counter associated with the number of Far End
                      unavailable seconds encountered by a DS3 interface
                      in the previous 24 hour interval." interval.  Invalid 15
                      minute intervals count as 0."
             ::= { dsx3FarEndTotalEntry 5 }
          -- the DS3/E3 Fractional Group

          -- This group is deprecated.
          -- Implementation of this group is was optional.  It is was designed
          -- for those systems dividing a DS3/E3 into channels
          -- containing different data streams that are of local
          -- interest.

          -- The DS3/E3 fractional table identifies which DS3/E3 channels
          -- associated with a CSU are being used to support a
          -- logical interface, i.e., an entry in the interfaces table
          -- from the Internet-standard MIB.

          -- For example, consider a DS3 device with 4 high speed links
          -- carrying router traffic, a feed for voice, a feed for video,
          -- and a synchronous channel for a non-routed protocol.
          -- We might describe the allocation of channels, in the
          -- dsx3FracTable, as follows:

          -- dsx3FracIfIndex.2. 1 = 3    dsx3FracIfIndex.2.15 = 4
          -- dsx3FracIfIndex.2. 2 = 3    dsx3FracIfIndex.2.16 = 6
          -- dsx3FracIfIndex.2. 3 = 3    dsx3FracIfIndex.2.17 = 6
          -- dsx3FracIfIndex.2. 4 = 3    dsx3FracIfIndex.2.18 = 6
          -- dsx3FracIfIndex.2. 5 = 3    dsx3FracIfIndex.2.19 = 6
          -- dsx3FracIfIndex.2. 6 = 3    dsx3FracIfIndex.2.20 = 6
          -- dsx3FracIfIndex.2. 7 = 4    dsx3FracIfIndex.2.21 = 6
          -- dsx3FracIfIndex.2. 8 = 4    dsx3FracIfIndex.2.22 = 6
          -- dsx3FracIfIndex.2. 9 = 4    dsx3FracIfIndex.2.23 = 6
          -- dsx3FracIfIndex.2.10 = 4    dsx3FracIfIndex.2.24 = 6
          -- dsx3FracIfIndex.2.11 = 4    dsx3FracIfIndex.2.25 = 6
          -- dsx3FracIfIndex.2.12 = 5    dsx3FracIfIndex.2.26 = 6
          -- dsx3FracIfIndex.2.13 = 5    dsx3FracIfIndex.2.27 = 6
          -- dsx3FracIfIndex.2.14 = 5    dsx3FracIfIndex.2.28 = 6

          -- For dsx3M23, dsx3SYNTRAN, dsx3CbitParity, and
          -- dsx3ClearChannel there are 28 legal channels,
          -- numbered 1 through 28.

          -- For e3Framed there are 16 legal channels,
          -- numbered 1 through 16.  The channels (1..16) correspond
          -- directly to the equivalently numbered time-slots.

          dsx3FracTable OBJECT-TYPE
              SYNTAX  SEQUENCE OF Dsx3FracEntry
              MAX-ACCESS  not-accessible
              STATUS  current  deprecated
              DESCRIPTION
                      "The DS3 Fractional table."
              ::= { ds3 13 }

          dsx3FracEntry OBJECT-TYPE
               SYNTAX  Dsx3FracEntry
               MAX-ACCESS  not-accessible
               STATUS  current  deprecated
               DESCRIPTION
                              "An entry in the DS3 Fractional table."
              INDEX   { dsx3FracIndex, dsx3FracNumber }
              ::= { dsx3FracTable 1 }

          Dsx3FracEntry ::=
              SEQUENCE {
                  dsx3FracIndex
                      INTEGER,
                  dsx3FracNumber
                      INTEGER,
                  dsx3FracIfIndex
                      INTEGER
              }

          dsx3FracIndex OBJECT-TYPE
              SYNTAX  INTEGER (1..'7fffffff'h)
              MAX-ACCESS  read-only
              STATUS  current  deprecated
              DESCRIPTION
                      "The index value which uniquely identifies  the
                      DS3  interface  to which this entry is applicable
                      The interface identified by a  particular value
                      of  this  index is the same interface as
                      identified by the same value  an  dsx3LineIndex
                      object instance."
             ::= { dsx3FracEntry 1 }

          dsx3FracNumber OBJECT-TYPE
              SYNTAX  INTEGER (1..31)
              MAX-ACCESS  read-only
              STATUS  current  deprecated
              DESCRIPTION
                      "The channel number for this entry."
             ::= { dsx3FracEntry 2 }
          dsx3FracIfIndex OBJECT-TYPE
              SYNTAX  INTEGER (1..'7fffffff'h)
              MAX-ACCESS  read-write
              STATUS  current  deprecated
              DESCRIPTION
                      "An index value that uniquely identifies an
                      interface.  The interface identified by a
                      particular value of this index is the same
                      interface as  identified by the same value an
                      ifIndex object instance. If no interface is
                      currently using a channel, the value should be
                      zero.  If a single interface occupies more  than
                      one  time slot,  that ifIndex value will be found
                      in multiple time slots."
             ::= { dsx3FracEntry 3 }

          -- conformance information

          ds3Conformance OBJECT IDENTIFIER ::= { ds3 14 }

          ds3Groups      OBJECT IDENTIFIER ::= { ds3Conformance 1 }
          ds3Compliances OBJECT IDENTIFIER ::= { ds3Conformance 2 }

          -- compliance statements

          ds3Compliance MODULE-COMPLIANCE
              STATUS  current
              DESCRIPTION
                      "The compliance statement for DS3/E3 interfaces."
              MODULE  -- this module
                  MANDATORY-GROUPS { ds3NearEndConfigGroup,
                                     ds3NearEndCurrentGroup,
                                     ds3NearEndIntervalGroup,
                                     ds3NearEndTotalGroup }

                  GROUP       ds3FarEndGroup
                  DESCRIPTION
                      "Implementation of this group is optional for all
                      systems that attach to a DS3 Interface.  However,
                      only C-bit Parity and SYNTRAN DS3 applications
                      have the capability (option) of providing this
                      information."
                  GROUP       ds3FracGroup       ds3NearEndOptionalConfigGroup
                  DESCRIPTION
                      "Implementation of this group is mandatory optional for all
                      systems dividing a DS3 into channels containing
                      different data streams that are of local interest.
                      Systems which are indifferent attach to data content,
                      such as CSUs, need not implement it." a DS3 interface."
              ::= { ds3Compliances 1 }

          -- units of conformance

          ds3NearEndConfigGroup  OBJECT-GROUP
              OBJECTS { dsx3TimeElapsed,
                        dsx3ValidIntervals,
                        dsx3LineType,
                        dsx3LineCoding,
                        dsx3SendCode,
                        dsx3CircuitIdentifier,
                        dsx3LoopbackConfig,
                        dsx3LineStatus,
                        dsx3TransmitClockSource
                        dsx3TransmitClockSource,
                        dsx3InvalidIntervals,
                        dsx3LineLength }
              STATUS  current
              DESCRIPTION
                      "A collection of objects providing configuration
                      information applicable to all DS3/E3 interfaces."
              ::= { ds3Groups 1 }

          ds3NearEndCurrentGroup OBJECT-GROUP
              OBJECTS { dsx3CurrentIndex,
                        dsx3CurrentPESs,
                        dsx3CurrentPSESs,
                        dsx3CurrentSEFSs,
                        dsx3CurrentUASs,
                        dsx3CurrentLCVs,
                        dsx3CurrentPCVs,
                        dsx3CurrentLESs,
                        dsx3CurrentCCVs,
                        dsx3CurrentCESs,
                        dsx3CurrentCSESs }
              STATUS  current
              DESCRIPTION
                      "A collection of objects providing statistics
                      information for the current interval applicable to
                      all DS3/E3 interfaces."
              ::= { ds3Groups 2 }
          ds3NearEndIntervalGroup OBJECT-GROUP
              OBJECTS { dsx3IntervalIndex,
                        dsx3IntervalNumber,
                        dsx3IntervalPESs,
                        dsx3IntervalPSESs,
                        dsx3IntervalSEFSs,
                        dsx3IntervalUASs,
                        dsx3IntervalLCVs,
                        dsx3IntervalPCVs,
                        dsx3IntervalLESs,
                        dsx3IntervalCCVs,
                        dsx3IntervalCESs,
                        dsx3IntervalCSESs
                        dsx3IntervalCSESs,
                        dsx3IntervalValidData }
              STATUS  current
              DESCRIPTION
                      "A collection of objects providing statistics
                      information for the last 96 intervals applicable
                      to all DS3/E3 interfaces."
              ::= { ds3Groups 3 }

          ds3NearEndTotalGroup OBJECT-GROUP
              OBJECTS { dsx3TotalIndex,
                        dsx3TotalPESs,
                        dsx3TotalPSESs,
                        dsx3TotalSEFSs,
                        dsx3TotalUASs,
                        dsx3TotalLCVs,
                        dsx3TotalPCVs,
                        dsx3TotalLESs,
                        dsx3TotalCCVs,
                        dsx3TotalCESs,
                        dsx3TotalCSESs }
              STATUS  current
              DESCRIPTION
                      "A collection of objects providing statistics
                      information for the total of the last 96 intervals
                      applicable to all DS3/E3 interfaces."
              ::= { ds3Groups 4 }

          ds3FarEndGroup  OBJECT-GROUP
              OBJECTS { dsx3FarEndLineIndex,
                        dsx3FarEndEquipCode,
                        dsx3FarEndLocationIDCode,
                        dsx3FarEndFrameIDCode,
                        dsx3FarEndUnitCode,
                        dsx3FarEndFacilityIDCode,
                        dsx3FarEndCurrentIndex,
                        dsx3FarEndTimeElapsed,
                        dsx3FarEndValidIntervals,
                        dsx3FarEndCurrentCESs,
                        dsx3FarEndCurrentCSESs,
                        dsx3FarEndCurrentCCVs,
                        dsx3FarEndCurrentUASs,
                        dsx3FarEndInvalidIntervals,
                        dsx3FarEndIntervalIndex,
                        dsx3FarEndIntervalNumber,
                        dsx3FarEndIntervalCESs,
                        dsx3FarEndIntervalCSESs,
                        dsx3FarEndIntervalCCVs,
                        dsx3FarEndIntervalUASs,
                        dsx3FarEndTotalIndex,
                        dsx3FarEndTotalCESs,
                        dsx3FarEndTotalCSESs,
                        dsx3FarEndTotalCCVs,
                        dsx3FarEndTotalUASs }
              STATUS  current
              DESCRIPTION
                      "A collection of objects providing remote
                      configuration and statistics information
                      applicable to C-bit Parity and SYNTRAN DS3
                      interfaces."
              ::= { ds3Groups 5 }

          ds3FracGroup

          ds3DeprecatedGroup OBJECT-GROUP
              OBJECTS { dsx3IfIndex,
                        dsx3LineIndex,
                        dsx3FracIndex,
                        dsx3FracNumber,
                        dsx3FracIfIndex }
              STATUS  current  deprecated
              DESCRIPTION
                      "A collection of obsolete objects providing information
                      about the division of a DS3 into channels of
                      different data." that may be
                      implemented for backwards compatibility."
              ::= { ds3Groups 6 }

          ds3DeprecatedGroup

          ds3NearEndOptionalConfigGroup OBJECT-GROUP
              OBJECTS { dsx3LineIndex,
                        dsx3IfIndex dsx3LineStatusLastChange,
                        dsx3LineStatusChangeTrapEnable }
              STATUS  deprecated    current
              DESCRIPTION
                      "A collection of obsolete objects that may be implemented for backwards compatibility."
                      on DS3/E3 interfaces."
              ::= { ds3Groups 7 }
           -- Ds3 TRAPS

          ds3Traps OBJECT IDENTIFIER ::= { ds3 15 }

          dsx3LineStatusChange NOTIFICATION-TYPE
              OBJECTS { dsx3LineStatus,
                        dsx3LineStatusLastChange }
              STATUS  current
              DESCRIPTION
                      "A dsx3LineStatusChange trap is sent when the
                      value of an instance dsx1LineStatus changes. It
                      can be utilized by an NMS to trigger polls.  When
                      the line status change results in a lower level
                      line status change (i.e. ds1), then no traps for
                      the lower level are sent."
                         ::= { ds3Traps 1 }

                      END

5.  Appendix A - Use of dsx3IfIndex and dsx3LineIndex

   Different physical configurations for the support of SNMP with DS3/E3
   equipment exist. To accommodate these scenarios, two different
   indices for DS3/E3 interfaces are introduced in this MIB.  These
   indices are dsx3IfIndex and dsx3LineIndex.

   External interface scenario: the SNMP Agent represents all managed
   DS3/E3 lines as external interfaces (for example, an Agent residing
   on the device supporting DS3/E3 interfaces directly):

   For this scenario, all interfaces are assigned an integer value equal
   to ifIndex, and the following applies:

      ifIndex=dsx3IfIndex=dsx3LineIndex for all interfaces.

   The dsx3IfIndex column of the DS3/E3 Configuration table relates each
   DS3/E3 interface to its corresponding interface (ifIndex) in the
   Internet-standard MIB (MIB-II STD 17, RFC1213).

   External&Internal interface scenario: the SNMP Agents resides on an
   host external from the device supporting DS3/E3 interfaces (e.g., a
   router). The Agent represents both the host and the DS3/E3 device.
   The index dsx3LineIndex is used to not only represent the DS3/E3
   interfaces external from the host/DS3/E3-device combination, but also
   the DS3/E3 interfaces connecting the host and the DS3/E3 device.  The
   index dsx3IfIndex is always equal to ifIndex.

   Example:

   A shelf full of CSUs connected to a Router. An SNMP Agent residing on
   the router proxies for itself and the CSU. The router has also an
   Ethernet interface:

         +-----+
   |     |     |
   |     |     |               +---------------------+
   |E    |     |  44.736 MBPS  |   ds3 M13    Line#A | ds3 C-bit Parity
   |t    |  R  |---------------+ - - - - -  - - -  - +------>
   |h    |     |               |                     |
   |e    |  O  |  44.736 MBPS  |   ds3 M13    Line#B | ds3 C-bit Parity
   |r    |     |---------------+ - - - - - - - - - - +------>
   |n    |  U  |               |                     |
   |e    |     |  44.736 MBPS  |   ds3 M13    Line#C | ds3 C-bit Parity
   |t    |  T  |---------------+ - - - -- -- - - - - +------>
   |     |     |               |                     |
   |-----|  E  |  44.736 MBPS  |   ds3 M13    Line#D | ds3 C-bit Parity
   |     |     |---------------+ -  - - - -- - - - - +------>
   |     |  R  |               |_____________________|
   |     |     |
   |     +-----+

   The assignment of the index values could for example be:

           ifIndex (= dsx3IfIndex)                     dsx3LineIndex

                   1                   NA                  NA (Ethernet)
                   2      Line#A   Router Side             6
                   2      Line#A   Network Side            7
                   3      Line#B   Router Side             8
                   3      Line#B   Network Side            9
                   4      Line#C   Router Side            10
                   4      Line#C   Network Side           11
                   5      Line#D   Router Side            12
                   5      Line#D   Network Side           13
   For this example, ifNumber is equal to 5.  Note the
   following description of dsx3LineIndex:
   the dsx3LineIndex identifies a DS3/E3 Interface on a managed
   device.  If there is an ifEntry that is directly associated with
   this and only this DS3/E3 interface, it should have the same value
   as ifIndex.  Otherwise, number the dsx3LineIndices with an unique
   identifier following the rules of choosing a number greater
   than ifNumber and numbering inside interfaces rules of choosing a number greater
   than ifNumber and numbering inside interfaces (e.g., equipment
   side) with even numbers and outside interfaces
   (e.g, network side) with odd numbers.

   If the CSU shelf is managed by itself by a local SNMP Agent,
   the situation would be:

           ifIndex (= dsx3IfIndex)                      dsx3LineIndex

                   1      Line#A     Network Side            1
                   2      Line#A     RouterSide              2
                   3      Line#B     Network Side            3
                   4      Line#B     RouterSide              4
                   5      Line#C     Network Side            5
                   6      Line#C     Router Side             6
                   7      Line#D     Network Side            7
                   8      Line#D     Router Side             8

6.  Appendix B - The delay approach to Unavialable Seconds.

   According to ANSI T1.231 unavailable time begins at the _onset_ of 10
   contiguous severely errored seconds -- that is, unavailable time
   starts with the _first_ of the 10 contiguous SESs.  Also, while an
   interface is deemed unavailable all counters for that interface are
   frozen except for the UAS count.  It follows that an implementation
   which strictly complies with this standard must _not_ increment any
   counters other than the UAS count -- even temporarily -- as a result
   of anything that happens during those 10 seconds.  Since changes in
   the signal state lag the data to which they apply by 10 seconds, an
   ANSI-compliant implementation must pass the the one-second statistics
   through a 10-second delay line prior to updating any counters.  That
   can be done by performing the following steps at the end of each one
   second interval.

   i)   Read near/far end CV counter and alarm status flags from the
        hardware.

   ii)  Accumulate the CV counts for the preceding second and
        compare them to the ES and SES threshold for the layer
        in question.  Update the signal state and shift the
        one-second CV counts and ES/SES flags into the 10-element
        delay line.  Note that far-end one-second statistics are
        to be flagged as "absent" during any second in which there
        is an incoming defect at the layer in question or at any
        lower layer.

   iii) Update the current interval statistics using the signal
        state from the _previous_ update cycle and the one-second
        CV counts and ES/SES flags shifted out of the 10-element
        delay line.

   This procedure is illustrated below for a SONET interface.  Similar
   rules would apply for DS1 and DS3 interfaces.  Note that the
   procedure guarantees that the statistical counters will be correctly
   updated at all times, although they will lag real time by 10 seconds.
   Each 15 minutes one would transfer the current interval counts into
   the previous interval counts and drop the oldest set of interval
   counts off the cliff.  Note that signal state calculations would
   _not_ start afresh at each interval boundary;  signal state
   information _would_ be carried across interval boundaries.  A scheme
   similar to this one has been used at least one DS1 product I know of
   -- the Tektronix/LP COM TC-2000 PCM test set.  This product was first
   put on the market in 1987 and featured G.821 performance statistics
   collected in the manner shown below.
       +--------------------------------------------------------------+
       |          READ COUNTERS & STATUS INFO FROM HARDWARE           |
       |                                                              |
       |LOS OOF/ SECT  LINE LINE LINE LINE  PATH PATH PATH PATH PATH  |
       |    LOF   CV    AIS  CV   RDI FEBE   AIS  LOP  CV   RDI  CV   |
       +--------------------------------------------------------------+
         |   |     |     |    |    |   |      |    |    |    |    |
         |   |     |     |    |    |   |      |    |    |    |    |
         V   V     V     V    V    V   V      V    V    V    V    V
       +--------------------------------------------------------------+
       | ACCUM ONE-SEC STATS, CHK ERR THRESHOLDS, & UPDT SIGNAL STATE |
       |                                                              |
       |                                                              |
       |                  NEAR END/FAR END       NEAR END/FAR END     |
       |SECT SECT SECT  LINE LINE LINE  LINE   PATH PATH PATH  PATH   |
       |CV   ES   SES    CV   ES   SES AVA/UNA  CV   ES   SES AVA/UNA |
       +--------------------------------------------------------------+
         |    |    |      |    |    |     |      |    |    |     |
         |    |    |      |    |    |     |      |    |    |     |
         V    V    V      V    V    V     |      V    V    V     |
       +-------------+  +-------------+   |    +-------------+   |
       |ONE-SEC DELAY|  |ONE-SEC DELAY|   |    |ONE-SEC DELAY|   |
       | (1 OF 10)   |  | (1 OF 10)   |   |    | (1 OF 10)   |   |
       |CV   ES   SES|  |CV   ES   SES|   |    |CV   ES   SES|   |
       +-------------+  +-------------+   |    +-------------+   |
         |    |    |      |    |    |     |      |    |    |     |
         /    /    /      /    /    /     /      /    /    /     /
         /    /    /      /    /    /     /      /    /    /     /
         |    |    |      |    |    |     |      |    |    |     |
         V    V    V      V    V    V     |      V    V    V     |
       +-------------+  +-------------+   |    +-------------+   |
       |ONE-SEC DELAY|  |ONE-SEC DELAY|   |    |ONE-SEC DELAY|   |
       | (10 OF 10)  |  | (10 OF 10)  |   |    | (10 OF 10)  |   |
       |CV   ES   SES|  |CV   ES   SES|   |    |CV   ES   SES|   |
       +-------------+  +-------------+   |    +-------------+   |
         |    |    |      |    |    |     |      |    |    |     |
         |    |    |      |    |    |     |      |    |    |     |
         V    V    V      V    V    V     V      V    V    V     V
       +--------------------------------------------------------------+
       |              UPDATE STATISTICS COUNTERS                      |
       |                                                              |
       |                   NEAR END/FAR END       NEAR END/FAR END    |
       |   SECTION               LINE                   PATH          |
       | CV ES EFS SES   CV ES EFS SES AS UAS   CV ES EFS SES AS UAS  |
       +--------------------------------------------------------------+

       Figure X.  Accumulation of SONET/SDH performance statistics.

   Adopting such a procedure would, however, raise another issue:  for
   the first ten seconds after a system comes up the interface is in an
   unknown state.  It would be necessary to allow for up to ten seconds
   of dead time during the current interval.  Hence the dsx1TimeElapsed,
   dsx1FarEndTimeElapsed, dsx3TimeElapsed, dsx3FarEndTimeElapsed, and
   sonetMediumTimeElapsed objects _would_ need to be replaced by objects
   that allow for the possibility that _no_ valid data has yet been
   collected for the current interval.  Here are some possible
   replacement objects:
             dsx1NearEndElapsedTime OBJECT-TYPE
                 SYNTAX  INTEGER (0..900)
                 MAX-ACCESS  read-only
                 STATUS  current
                 DESCRIPTION
                         "The number of seconds, including partial
                          seconds, that have elapsed since the beginning of
                         the current near-end error-measurement period."
                 ::= { dsx1ConfigEntry xxx }

            dsx1FarEndElapsedTime OBJECT-TYPE
                SYNTAX  INTEGER (0..900)
                MAX-ACCESS  read-only
                STATUS  current
                DESCRIPTION
                         "The number of seconds, including partial
                          seconds, that have elapsed since the beginning of
                         the current far-end error-measurement period."
               ::= { dsx1FarEndCurrentEntry xxx }

             dsx3NearEndElapsedTime OBJECT-TYPE
                 SYNTAX  INTEGER (0..900)
                 MAX-ACCESS  read-only
                 STATUS  current
                 DESCRIPTION
                         "The number of seconds, including partial
                          seconds, that have elapsed since the beginning of
                         the current near-end error-measurement period."
                 ::= { dsx3ConfigEntry xxx }

             dsx3FarEndElapsedTime OBJECT-TYPE
                 SYNTAX  INTEGER (0..900)
                 MAX-ACCESS  read-only
                 STATUS  current
                 DESCRIPTION
                         "The number of seconds, including partial
                          seconds, that have elapsed since the beginning of
                          the current far-end error-measurement period."
                 ::= { dsx3FarEndCurrentEntry xxx }

             sonetMediumElapsedTime OBJECT-TYPE
                 SYNTAX  Integer32 (0..900)
                 MAX-ACCESS  read-only
                 STATUS  current
                 DESCRIPTION
                    "The number of seconds, including partial
                    seconds, that have elapsed since the beginning of
                    the current error-measurement period."
                 ::= { sonetMediumEntry xxx }
   These objects should assume the value 0 whenever there are no current
   interval statistics to report.  That would happen if the interface
   was off-line (e.g., equipment
   side) with even numbers in a disabled or testing state) and outside interfaces
   (e.g, network side) (in an
   implementation which fully complies with odd numbers.

   If ANSI T1.231 UAS definition)
   during the CSU shelf is managed by itself by a local SNMP Agent, initial 10-second period after the situation would be:

           ifIndex (= dsx3IfIndex)                      dsx3LineIndex
                   1      Line#A     Network Side            1
                   2      Line#A     RouterSide              2
                   3      Line#B     Network Side            3
                   4      Line#B     RouterSide              4
                   5      Line#C     Network Side            5
                   6      Line#C     Router Side             6
                   7      Line#D     Network Side            7
                   8      Line#D     Router Side             8

6. interface is brought
   on-line.

7.  Acknowledgments

   This document was produced by the Trunk MIB Working Group:

7.

8.  References

      [1] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and
          S. Waldbusser, "Structure of Management Information for version Version 2
          of the Simple Network Management Protocol (SNMPv2)", RFC 1442,
          SNMP Research,Inc., Hughes LAN Systems, Dover Beach
          Consulting, Inc., Carnegie Mellon University, April 1993. 1902,
          January 1996.

      [2] McCloghrie, K., and M. Rose, Editors, "Management
          Information Base for Network Management of TCP/IP-based
          internets: MIB-II", STD 17, RFC 1213, Hughes LAN Systems,
          Performance Systems International, March 1991.

      [3] Galvin, Case, J., Fedor, M., Schoffstall, M., and K. McCloghrie, "Administrative Model for
          version 2 of the J. Davin. " A Simple
          Network Management Protocol
          (SNMPv2)", (SNMP)", STD 15, RFC 1445, Trusted Information Systems, Hughes
          LAN Systems, April 1993. 1157, SNMP
          Research, Performance Systems International, MIT Lab for
          Computer Science, May 1990.

      [4] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and
          S. Waldbusser, "Protocol Operations for version Version 2 of the Simple
          Network Management Protocol (SNMPv2)", RFC 1448, SNMP
          Research,Inc., Hughes LAN Systems, Dover Beach
          Consulting, Inc., Carnegie Mellon University, April 1993. 1905, January 1996.

      [5] McCloghrie, K. and F. Kastenholz, "Evolution of the
          Interfaces Group of MIB-II", RFC 1573, Hughes LAN
          Systems, FTP Software, January 1994.

      [6] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
          "Textual Conventions for SNMPv2", RFC1443, SNMP
          Research,Inc., Hughes LAN Systems, Dover Beach
          Consulting, Inc., Carnegie Mellon University, April 1993.

      [7] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
          "Conformance Statements for SNMPv2", RFC1444, SNMP
          Research,Inc., Hughes LAN Systems, Dover Beach
          Consulting, Inc., Carnegie Mellon University, April 1993.

      [8] Baker, F., and Watt, J., Fowler D., "Definitions of Managed Objects
          for the DS1 and E1 Interface Types", RFC1406, RFCxxxx, Advanced
          Computer Communications, Newbridge Networks Corporation,
          January 1993.

      [9]

      [7] Brown, T., and Tesink, K., "Definitions of Managed Objects
          for the SONET/SDH Interface Type", RFC1595, Bell Communications
          Research, March 1994.

     [10]

      [8] American National Standard for telecommunications - digital
          hierarchy - electrical interfaces, ANSI T1.102- 1987.

     [11]

      [9] American National Standard for telecommunications - digital
          hierarchy - formats specification, ANSI T1.107- 1988.

     [11a]

     [9a] ANSI T1.107a-1990.

     [12]

     [10] American National Standard for telecommunications - Carrier-to-
          Customer Installation - DS3 Metallic Interface,
          ANSI T1.404-1989.

     [13]

     [11] American National Standard for Telecommunications --
          Layer 1 In-Service Digital Transmission Performance Monitoring
          T1.231, Sept 1993.

     [14]

     [12] CCITT - Digital Multiplex Equipment Operating at the Third
          Order Bit Rate of 34 368 Kbit/s and the Forth Order Bit Rate
          of 139 264 Kbit/s and Using Positive Justification, G.751

     [15]

     [13] European Telecommunications Standards Institute --
          ETS "34M" -- Metropolitan Area Network Physical Convergence
          Layer Procedure for 34.368 Megabits per Second,
          T/NA(91)18, May 1991.

8.

9.  Security Considerations

   Security issues are not discussed in this memo.

9.

10.  Authors' Addresses

      David Fowler
      Newbridge Networks
      600 March Road
      Kanata, Ontario, Canada K2K 2E6

      Phone: (613) 599-3600, ext 3538

      EMail: davef@newbridge.com
   Table of Contents

   1 The SNMPv2 Network Management Framework ......................    2
   2 Objects ...................................................... Object Definitions ...........................................    3
   2.1 Changes from RFC1233 RFC1407 .......................................    3
   3 Overview .....................................................    5    4
   3.1 Use of ifTable for DS1 DS3 Layer ...............................    5    4
   3.2 Using ifStackTable .........................................    6    5
   3.3 Objectives of this MIB Module ..............................    8    7
   3.4 DS3/E3 Terminology .........................................    8
   3.4.1 Error Events .............................................    9    8
   3.4.2 Performance Parameters ...................................    9
   3.4.3 Performance Defects ......................................   11
   3.4.4 Other Terms ..............................................   13   12
   4 Object Definitions ...........................................   14
   5.1   13
   4.1 The DS3/E3 Near End Group ..................................   15
   5.1.1   14
   4.1.1 The DS3/E3 Configuration .................................   15
   5.1.2   14
   4.1.2 The DS3/E3 Current ....................................... Table .................................   22
   5.1.3
   4.1.3 The DS3/E3 Interval ...................................... Table ................................   26
   5.1.4
   4.1.4 The DS3/E3 Total .........................................   31
   5.2
   4.2 The DS3 Far End Group ......................................   35
   5.2.1
   4.2.1 The DS3 Far End Configuration ............................   35
   5.2.2
   4.2.2 The DS3 Far End Current ..................................   37
   5.2.3
   4.2.3 The DS3 Far End Interval ................................. Table ...........................   40
   5.2.4
   4.2.4 The DS3 Far End Total ....................................   43
   5.3
   4.3 The DS3/E3 Fractional Group ................................   46
   4.4 Conformance Groups .........................................   48
   4.5 The DS3 Trap Group .........................................   53
   5 Appendix A - Use of dsx3IfIndex and dsx3LineIndex ............   52   53
   6 Appendix B - The delay approach to Unavialable Seconds.  .....   55
   7 Acknowledgments ..............................................   54
   7   59
   8 References ...................................................   55
   8   60
   9 Security Considerations ......................................   57
   9   62
   10 Authors' Addresses ...........................................   57 ..........................................   62