INTERNET-DRAFT                               Charles H. Lindsey
Usenet Format Working Group                  University of Manchester
                                             July 2001

                          News Article Format

Status of this Memo

   This document is an Internet-Draft and is in full conformance with
   all provisions of Section 10 of RFC 2026.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups. Note that
   other groups may also distribute working documents as Internet-

   Internet-Drafts are draft documents valid for a maximum of six
   months and may be updated, replaced, or obsoleted by other
   documents at any time. It is inappropriate to use Internet-Drafts
   as reference material or to cite them other than as "work in

   The list of current Internet-Drafts can be accessed at

   The list of Internet-Draft Shadow Directories can be accessed at


   This Draft defines the format of Netnews articles and specifies
   the requirements to be met by software which originates,
   distributes, stores and displays them. It is intended as a
   standards track document, superseding RFC 1036, which itself dates
   from 1987.

   Since the 1980s, Usenet has grown explosively, and many Internet and
   non-Internet sites now participate. In addition, this technology is
   now in widespread use for other purposes.

   Backward compatibility has been a major goal of this endeavour, but
   where this standard and earlier documents or practices conflict, this
   standard should be followed. In most such cases, current practice is
   already compatible with these changes.

[The use of the words "this standard" within this document when
referring to itself does not imply that this draft yet has pretensions
to be a standard, but rather indicates what will become the case if and
when it is accepted as an RFC with the status of a proposed or draft
                          News Article Format                 April                  July 2001

[Remarks enclosed in square brackets and aligned with the left margin,
such as this one, are not part of this draft, but are editorial notes to
explain matters amongst ourselves, or to point out alternatives, or to
indicate work yet to be done.]

[Please note that this Draft describes "Work in Progress". Much remains
to be done, though the material included so far is unlikely to change in
any major way.]

                           Table of Contents

1.  Introduction ..................................................    5
  1.1.  Basic Concepts ............................................    5
  1.2.  Objectives ................................................    6
  1.3.  Historical Outline ........................................    6
  1.4.  Transport .................................................    6
2.  Definitions, Notations and Conventions ........................    6
  2.1.  Definitions.  .............................................  Definitions ...............................................    7
  2.2.  Textual Notations .........................................    8
  2.3.  Relation To Mail and MIME .................................    9   10
  2.4.  Syntax Notation ...........................................   10
  2.5.  Language ..................................................   12   13
3.  Changes to the existing protocols .............................   13
  3.1.  Principal Changes .........................................   13
  3.2.  Transitional Arrangements .................................   13   14
4.  Basic Format ..................................................   15
  4.1.  Syntax of News Articles ...................................   15
  4.2.  Headers ...................................................   16
    4.2.1.  Names and Contents ....................................   16
    4.2.2.  Header Properties .....................................   17   18  Experimental Headers ..............................   17   18  Inheritable Headers ...............................   18  Local Headers .....................................   18  Variant Headers ...................................   18
    4.2.3.  White Space and Continuations .........................   18   19
    4.2.4.  Comments ..............................................   19   20
    4.2.5.  Undesirable Headers ...................................   20
  4.3.  Body ......................................................   20   21
    4.3.1.  Body Format Issues ....................................   20   21
    4.3.2.  Body Conventions ......................................   21
  4.4.  Characters and Character Sets .............................   22   23
    4.4.1.  Character Sets within Article Headers .................   23
    4.4.2.  Character Sets within Article Bodies ..................   24
  4.5.  Size Limits ...............................................   24   25
  4.6.  Example ...................................................   25   26
5.  Mandatory Headers .............................................   26   27
  5.1.  Date ......................................................   26   27
    5.1.1.  Examples ..............................................   26   28
  5.2.  From ......................................................   27   28
    5.2.1.  Examples:  ............................................   27   28
  5.3.  Message-ID ................................................   28   29
  5.4.  Subject ...................................................   28   29
    5.4.1.  Examples ..............................................   29   30
  5.5.  Newsgroups ................................................   31
                          News Article Format                 April                  July 2001

  5.5.  Newsgroups ................................................   29

    5.5.1.  Forbidden newsgroup names .............................   31   35
  5.6.  Path ......................................................   32   36
    5.6.1.  Format ................................................   32   36
    5.6.2.  Adding a path-identity to the Path header .............   33   37
    5.6.3.  The tail-entry ........................................   34   38
    5.6.4.  Delimiter Summary .....................................   35   38
    5.6.5.  Suggested Verification Methods ........................   35   39
    5.6.6.  Example ...............................................   36   40
6.  Optional Headers ..............................................   37   41
  6.1.  Reply-To ..................................................   37   41
    6.1.1.  Examples ..............................................   38   41
  6.2.  Sender ....................................................   38   42
  6.3.  Organization ..............................................   38   42
  6.4.  Keywords ..................................................   38   42
  6.5.  Summary ...................................................   39   42
  6.6.  Distribution ..............................................   39   43
  6.7.  Followup-To ...............................................   40   44
  6.8.  Mail-Copies-To ............................................   41   44
  6.9.  Posted-And-Mailed .........................................   42   45
  6.10.  References ...............................................   42   46
    6.10.1.  Examples .............................................   43   46
  6.11.  Expires ..................................................   43   47
  6.12.  Archive ..................................................   43   47
  6.13.  Control ..................................................   44   48
  6.14.  Approved .................................................   44   48
  6.15.  Replaces / Supersedes ....................................   45   49
    6.15.1.  Syntax and Semantics .................................   45   49
    6.15.2.  Message-ID version procedure .........................   46   50  Message version numbers ..........................   47   51  Implementation and Use Note ......................   48   52  The Message-Version NNTP extension ...............   50   54  Examples .........................................   50   54
  6.16.  Xref .....................................................   51   55
  6.17.  Lines ....................................................   53   57
  6.18.  User-Agent ...............................................   53   57
    6.18.1.  Examples .............................................   54   58
  6.19.  Injector-Info ............................................   54   58
    6.19.1.  Usage of Injector-Info-header-parameters .............   56   60  The posting-host-parameter .......................   56   60  The posting-account-parameter ....................   57   61  The posting-sender-parameter .....................   57   61  The posting-logging-parameter ....................   57   61  The posting-date-parameter .......................   57   61
    6.19.2.  Example ..............................................   57   61
  6.20.  Complaints-To ............................................   57   61
  6.21.  MIME headers .............................................   58   62
    6.21.1.  Syntax ...............................................   58   62
    6.21.2.  Content-Transfer-Encoding ............................   58
    6.21.3.  Content-Type .........................................   59   62  Message/partial ..................................   59   63  Message/rfc822 ...................................   60   63  Message/external-body ............................   60   64  Multipart types ..................................   61
                          News Article Format                 April 2001   64
    6.21.3.  Content-Transfer-Encoding ............................   65
    6.21.4.  Character Sets .......................................   61   66
                          News Article Format                  July 2001

    6.21.5.  Content Disposition ..................................   61   67
    6.21.6.  Definition of some new Content-Types .................   61   67  Application/news-transmission ....................   62   67  Message/news withdrawn ...........................   63   68
  6.22.  Obsolete Headers .........................................   63   68
7.  Control Messages ..............................................   63   69
  7.1.  The 'newgroup' Control Message ............................   64   69
    7.1.1.  The Body of the 'newgroup' Control Message ............   65   70
    7.1.2.  Application/news-groupinfo ............................   65   71
    7.1.3.  Initial Articles ......................................   67   72
    7.1.4.  Example ...............................................   67   73
  7.2.  The 'rmgroup' Control Message .............................   68   74
    7.2.1.  Example ...............................................   69   74
  7.3.  The 'mvgroup' Control Message .............................   69   74
    7.3.1.  Single group ..........................................   69   74
    7.3.2.  Multiple Groups .......................................   70   75
    7.3.3.  Examples ..............................................   70   76
  7.4.  The 'checkgroups' Control Message .........................   71   77
    7.4.1.  Application/news-checkgroups ..........................   72   78
  7.5.  Cancel ....................................................   73   78
  7.6.  Ihave, sendme .............................................   74   80
  7.7.  Obsolete control messages.  ...............................   75   81
8.  Duties of Various Agents ......................................   76   81
  8.1.  General principles to be followed .........................   76   81
  8.2.  Duties of an Injecting Agent ..............................   76   82
    8.2.1.  Proto-articles ........................................   77   82
    8.2.2.  Procedure to be followed by Injecting Agents ..........   77   82
  8.3.  Duties of a Relaying Agent ................................   78   84
  8.4.  Duties of a Serving Agent .................................   79   85
  8.5.  Duties of a Posting Agent .................................   80   86
  8.6.  Duties of a Followup Agent ................................   80   86
  8.7.  Duties of a Moderator .....................................   81   87
  8.8.  Duties of a Gateway .......................................   82   88
    8.8.1.  Duties of an Outgoing Gateway .........................   83   89
    8.8.2.  Duties of an Incoming Gateway .........................   84   90
    8.8.3.  Example ...............................................   86   92
9.  Security and Related Considerations ...........................   87   93
  9.1.  Leakage ...................................................   87   93
  9.2.  Attacks ...................................................   87   93
    9.2.1.  Denial of Service .....................................   87   93
    9.2.2.  Compromise of System Integrity ........................   88   94
  9.3.  Liability .................................................   89   95
10.  References ...................................................   90   96
11.  Acknowledgements .............................................   92   98
12.  Contact Addresses ............................................   92   98
13.  Intellectual Property Rights .................................   92   99
Appendix A.1 - A-News Article Format ..............................   93  100
Appendix A.2 - Early B-News Article Format ........................   94  100
Appendix A.3 - Obsolete Headers ...................................   95  101
Appendix A.4 - Obsolete Control Messages ..........................   95  101
Appendix B - Collected Syntax .....................................   96  102
                          News Article Format                 April                  July 2001

1.  Introduction

1.1.  Basic Concepts

   "Netnews" is a set of protocols for generating, storing and
   retrieving news "articles" (which resemble mail messages) and for
   exchanging them amongst a readership which is potentially widely
   distributed. It is organized around "newsgroups," "newsgroups", with the
   expectation that each reader will be able to see all articles posted
   to each newsgroup in which he participates. These protocols most
   commonly use a flooding algorithm which propagates copies throughout
   a network of participating servers.  Typically, only one copy is
   stored per server, and each server makes it available on demand to
   readers able to access that server.

   An important characteristic of Netnews is the lack of any requirement
   for a central administration or for the establishment of any
   controlling host to manage the network. A network which limits
   participation to some restricted set of hosts (within some company,
   for example) is a "closed" network; otherwise it is an "open"
   network. A set of hosts within a network which, by mutual
   arrangement, operates some variant (whether more or less restrictive)
   of the Netnews protocols is a "cooperating subnet".

   "Usenet" is a particular worldwide open network based upon the
   Netnews protocols, with the newsgroups being organised into
   recognized "hierarchies".  Anybody can join (it is simply necessary
   to negotiate an exchange of articles with one or more other
   participating hosts). Usenet "belongs" to those who administer the
   hosts of which it is comprised. There is no Cabal with overall
   authority to direct what is to be be allowed. Nevertheless, there do
   exist agencies within Usenet that have authority to establish
   policies and to perform administrative functions, but such authority
   derives solely from the consent of those sites which choose to
   recognise it (and who can decline to exchange articles with sites
   which choose not to recognise it). Usually, the authority of such an
   agency is restricted to a particular hierarchy, or group of

   A "policy" is a rule intended to facilitate the smooth operation of a
   network by establishing parameters which restrict behaviour that,
   whilst technically unexceptionable, would nevertheless contravene
   some accepted standard of "Good Netkeeping". Since the ultimate
   beneficiaries of a network are its human readers, who will be less
   tolerant of poorly designed interfaces than mere computers, articles
   in breach of established policy can cause considerable annoyance to
   their recipients.

   Policies may well vary from network to network, from hierarchy to
   hierarchy within one network, and even between individual newsgroups
   within one hierarchy. It is assumed, for the purposes of this
   standard, that agencies with varying degrees of authority to
   establish such policies will exist, and that where they do not,
   policy will be established by mutual agreement.  For the benefit of
                          News Article Format                 April                  July 2001

   networks and hierarchies without such established agencies, and to
   provide a basis upon which all agencies can build, this present
   standard often provides default policy parameters, usually
   introducing them by a phrase such as "As a matter of policy ...".

1.2.  Objectives

   The purpose of this present standard is to define the protocols to be
   used for Netnews in general, and for Usenet in particular, and to set
   standards to be followed by software that implements those protocols.

   It is NOT the purpose of this standard to define how the authority of
   various agencies to exercise control or oversight of the various
   parts of Usenet is established (that is itself a matter of policy).
   Nevertheless, it is assumed that such authorities will exist, and
   tools are provided within the protocols for their use.

1.3.  Historical Outline

   Network news originated as the medium of communication for Usenet,
   circa 1980.  Since then, Usenet has grown explosively, and many
   Internet and non-Internet sites participate in it.  In addition, the
   news technology is now in widespread use for other purposes, on the
   Internet and elsewhere.

   The earliest news interchange used the so-called "A News" article
   format.  Shortly thereafter, an article format vaguely resembling
   Internet mail was devised and used briefly.  Both of those formats
   are completely obsolete; they are documented in Appendix A.1 and
   Appendix A.2 for historical reasons only.  With publication of [RFC
   850] in 1983, news articles came to closely resemble Internet mail
   messages, with some restrictions and some additional headers. [RFC
   1036] in 1987 updated [RFC 850] without making major changes.

   A Draft popularly referred to as "Son of 1036" [Son-of-1036] was
   written in 1994 by Henry Spencer. That document formed the original
   basis for this standard. Much is taken directly from Son of 1036, and
   it is hoped that we have followed its spirit and intentions.

1.4.  Transport

   As in this standard's predecessors, the exact means used to transmit
   articles from one host to another is not specified. NNTP [NNTP] is
   the most common transmission method on the Internet, but much
   transmission takes place entirely independent of the Internet. Other
   methods in use include the UUCP protocol [RFC 976] extensively used
   in the early days of Usenet, FTP, downloading via satellite, tape
   archives, and physically delivered magnetic and optical media.

2.  Definitions, Notations and Conventions
                          News Article Format                 April                  July 2001

2.1.  Definitions.  Definitions

   An "article" is the unit of news, analogous to a [MESSFOR] an [RFC 2822]
   "message". A "proto-article" is one that has not yet been injected
   into the news system.

   A "message identifier" (5.3) is a unique identifier for an article,
   usually supplied by the "posting agent" which posted it or, failing
   that, by the "injecting agent". It distinguishes the article from
   every other article ever posted anywhere. Articles with the same
   message identifier are treated as if they are the same article
   regardless of any differences in the body or headers.

   A "newsgroup" is a single news forum, a logical bulletin board,
   having a name and nominally intended for articles on a specific
   topic. An article is "posted to" a single newsgroup or several
   newsgroups. When an article is posted to more than one newsgroup, it
   is said to be "crossposted"; note that this differs from posting the
   same text as part of each of several articles, one per newsgroup.

   A newsgroup may be "moderated", in which case submissions are not
   posted directly, but mailed to a "moderator" for consideration and
   possible posting.  Moderators are typically human but may be
   implemented partially or entirely in software.

   A "hierarchy" is the set of all newsgroups whose names share a first
   component (as defined in 5.5).  The term "sub-hierarchy" is also used
   where several initial components are shared.

   A "poster" is the person or software that composes and submits a
   possibly compliant article to a "posting agent". The poster is
   analogous to [MESSFOR]'s [RFC 2822]'s author(s).

   A "posting agent" is the software that assists posters to prepare
   proto-articles, in compliance with this standard. The proto-article
   is then passed on to an "injecting agent" for final checking and
   injection into the news stream. If the article is not compliant, or
   is rejected by the injecting agent, then the posting agent informs
   the poster with an explanation of the error.

   A "reader" is the person or software reading news articles.

   A "reading agent" is software which presents articles to a reader.

   A "followup" is an article containing a response to the contents of
   an earlier article (the followup's "precursor").

   A "followup agent" is a combination of reading agent and posting
   agent that aids in the preparation and posting of a followup.

   An article's "reply address" is the address to which mailed replies
   should be sent. This is the address specified in the article's From
   header (5.2), unless it also has a Reply-To header (6.1).

                          News Article Format                 April                  July 2001

   A "reply agent" is a combination of reading agent and mailer that
   aids in the preparation and posting of an email response to an

   A "sender" is the person or software (usually, but not always, the
   same as the poster) responsible for the operation of the posting
   agent or, which amounts to the same thing, for passing the article to
   the injecting agent. The sender is analogous to [MESSFOR]'s [RFC 2822]'s sender.

   An "injecting agent" takes the finished article from the posting
   agent (often via the NNTP "post" command) performs some final checks
   and passes it on to a relaying agent for general distribution.

   A "relaying agent" is software which receives allegedly compliant
   articles from injecting agents and/or other relaying agents, and
   possibly passes copies on to other relaying agents and serving

   A "news database" is the set of articles and related structural
   information stored by a serving agent and made available for access
   by reading agents.

   A "serving agent" receives an article from a relaying agent and files
   it in a news database. It also provides an interface for reading
   agents to access the news database.

   A "control message" is an article which is marked as containing
   control information; a relaying or serving agent receiving such an
   article may (subject to the policies observed at that site) take
   actions beyond just filing and passing on the article.

   A "gateway" is software which receives news articles and converts
   them to messages of some other kind (e.g. mail to a mailing list), or
   vice versa; in essence it is a translating relaying agent that
   straddles boundaries between different methods of message exchange.
   The most common type of gateway connects newsgroup(s) to mailing
   list(s), either unidirectionally or bidirectionally, but there are
   also gateways between news networks using this standard's news format
   and those using other formats.

2.2.  Textual Notations

   This standard contains explanatory NOTEs using the following format.
   These may be skipped by persons interested solely in the content of
   the specification. The purpose of the notes is to explain why choices
   were made, to place them in context, or to suggest possible
   implementation techniques.

        NOTE: While such explanatory notes may seem superfluous in
        principle, they often help the less-than-omniscient reader grasp
        the purpose of the specification and the constraints involved.
        Given the limitations of natural language for descriptive
        purposes, this improves the probability that implementors and
        users will understand the true intent of the specification in
                          News Article Format                 April                  July 2001

        cases where the wording is not entirely clear.


   "US-ASCII" is short for "the ANSI X3.4 character set" [ANSI X3.4].
   While "ASCII" is often misused to refer to various character sets
   somewhat similar to X3.4, in this standard "ASCII" means "US-ASCII" is used to mean
   X3.4 and only X3.4. ASCII US-ASCII is a 7 bit character set. Please note
   that this standard requires that all agents be 8 bit clean; that is,
   they must accept and transmit data without changing or omitting the
   8th bit.

   Certain words, when capitalized, are used to define the significance
   of individual requirements. The key words "MUST", "REQUIRED",
   "SHOULD", "RECOMMENDED", "MAY" and "OPTIONAL", and any of those words
   associated with the word "NOT", are to be interpreted as described in
   [RFC 2119].

   In addition, the word "Ought", when applied to a poster, or to
   actions of posting and similar agents which a poster may easily
   override, indicates a recommendation whose violation would do no more
   than breach established policy, or accepted best practice.

        NOTE: The use of "MUST" or "SHOULD" implies a requirement that
        would or could lead to interoperability problems if not
        followed. Although not following an "Ought" recommendation might
        do no worse than cause extreme irritation to other readers,
        particularly in the case of the publicly distributed Usenet,
        that is no reason not to take it seriously. The essential
        distinction is that enforcement of a "MUST" or "SHOULD" is a
        matter of ensuring correct implementation, whereas enforcement
        of an "Ought" is more a matter of sensible design or of social
        pressure (whose effectiveness should not be underestimated, even
        though it cannot be prescribed by this standard).

        NOTE: A requirement imposed on a relaying or serving agent
        should be understood as applying only to articles actually
        accepted for processing by that agent (since any agent may
        always reject any article entirely, for reasons of site policy).

   All numeric values are given in decimal unless otherwise indicated.
   Octets are assumed to be unsigned values for this purpose.

   Throughout this standard we will give examples of various
   definitions, headers and other specifications. It needs to be
   remembered that these samples are for the aid of the reader only and
   do NOT define any specification themselves.  In order to prevent
   possible conflict with "Real World" entities and people the top level
   domain of ".example" is used in all sample domains and addresses. The
   hierarchy of example.* is also used as a sample hierarchy.
   Information on the ".example" top level domain is in [RFC 2606].

                          News Article Format                  July 2001

2.3.  Relation To Mail and MIME

   The primary intent of this standard is to describe the news article
   format.  Insofar as news articles are a subset of the Mail message
   format augmented by some new headers, this standard incorporates many
                          News Article Format                 April 2001
   (though not all) of the provisions of [MESSFOR], [RFC 2822], with the aim of
   enabling news articles to pass through mail systems and vice versa,
   provided only that they contain the minimum headers required for the
   mode of transport being used. Unfortunately, the match is not
   perfect, but it is the intention of this standard that gateways
   between Mail and News should be able to operate with the minimum of
[This standard has been designed to fit on top of the drafts currently
in preparation for Mail [MESSFOR].  It is expected that those drafts
will have progressed to the RFC stage by the time the present standard
in complete, at which time all references to [MESSFOR] in the present
text will be replaced by references to that RFC.]

   Likewise, this standard incorporates many (though not all) of the
   provisions of the MIME standards [RFC 2045] et seq which, though
   designed with Mail in mind, are mostly applicable to News.

2.4.  Syntax Notation

   This standard uses the Augmented Backus Naur Form described in [RFC
   2234].  A discussion of this is outside the bounds of this standard,
   but it is expected that implementors will be able quickly to
   understand it with reference to that defining document.

   Much of the syntax of News Articles is based on the corresponding
   syntax defined in [MESSFOR] [RFC 2822] or in the Mime MIME specifications [RFC 2045]
   et seq, which is deemed to have been incorporated into this standard
   as required. However, there are some important differences arising
   from the fact that [MESSFOR] [RFC 2822] does not recognise anything other than
   US-ASCII characters, that it does not recognise the MIME headers [RFC
   2045], and that it includes much syntax described as "obsolete".

        NOTE: News parsers historically have been much less permissive
        than Mail parsers, and this is reflected in the modifications
        referred to, and in some further specific rules.

   The following syntactic forms therefore supersede the corresponding
   rules given in [MESSFOR] [RFC 2822] and [RFC 2045], thus allowing UTF-8
   characters [RFC 2044] 2279] to appear in certain contexts (the four five rules
   begining with "strict-" reflect the corresponding original rules from

      UTF8-xtra-head  = %d192-253
   [RFC 2822]).

      UTF8-xtra-2-head= %xC2-DF
      UTF8-xtra-3-head= %xE0 %xA0-BF / %xE1-EC %x80-BF /
                      = %xED %x80-9F / %xEE-EF %x80-BF
      UTF8-xtra-4-head= %xF0 %x90-BF / %xF1-F7 %x80-BF
      UTF8-xtra-5-head= %xF8 %x88-BF / %xF9-FB %x80-BF
      UTF8-xtra-6-head= %xFC %x84-BF / %xFD    %x80-BF
      UTF8-xtra-tail  = %d128-191 %x80-BF
      UTF8-xtra-char  = UTF8-xtra-head 1*UTF8-xtra-tail UTF8-xtra-2-head 1( UTF8-xtra-tail ) /
                        UTF8-xtra-3-head 1( UTF8-xtra-tail ) /
                        UTF8-xtra-4-head 2( UTF8-xtra-tail ) /
                        UTF8-xtra-5-head 3( UTF8-xtra-tail ) /
                        UTF8-xtra-6-head 4( UTF8-xtra-tail )
                          News Article Format                  July 2001

      text            = %d1-9 /            ; all UTF-8 characters except
                        %d11-12 /          ; US-ASCII NUL, CR and LF
                        %d14-127 /
      ctext           = NO-WS-CTL /        ; all of <text> except
                        %d33-39 /          ; SP, HTAB, "(", ")"
                        %d42-91 /          ; and "\"
                        %d93-126 /
                          News Article Format                 April 2001
      qtext           = NO-WS-CTL /        ; all of <text> except
                        %d33 /             ; SP, HTAB, "\" and DQUOTE
                        %d35-91 /
                        %d93-126 /
      utext           = NO-WS-CTL /        ; Non white space controls
                        %d33-126 /         ; The rest of US-ASCII
      strict-text     = %d1-9 /            ; text restricted to
                        %d11-12 /          ; US-ASCII
      strict-qtext    = NO-WS-CTL /        ; qtext restricted to
                        %d33 /             ; US-ASCII
                        %d35-91 /
                      = "\" strict-text
      strict-qcontent = strict-qtext / strict-quoted-pair
                      = [CFWS]
                           DQUOTE *([FWS] (strict-qtext / strict-quoted-pair)) strict-qcontent) [FWS] DQUOTE

        NOTE: There are

   The syntax for UTF8-xtra-char excludes those redundant sequences of
   octets which cannot legitimately occur in UTF-8, even a few permitted as defined by [RFC 2279], either
   because they would not be the above syntax. shortest possible encodings of some UCS
   character, or they would represent one of the characters D800 through
   DFFF, disallowed in UCS because of their surrogate use in the UTF-16
   encoding.  These
        SHOULD sequences MUST NOT be generated by posting agents but, where agents.
   Where they occur inadavertently, they SHOULD MAY be passed on untouched by
        agents. agents, but they MUST NOT ever be interpreted as valid

   Wherever in this standard the syntax is stated to be taken from
   2822], it is to be understood as the syntax defined by [MESSFOR] [RFC 2822]
   after making the above changes, but NOT including any syntax defined
   in section 4 ("Obsolete syntax") of [MESSFOR]. [RFC 2822].  Software compliant
   with this standard MUST NOT generate any of the syntactic forms
   defined in that Obsolete Syntax, although it MAY accept such
   syntactic forms. Certain syntax from the MIME specifications [RFC
   2045] et seq is also considered a part of this standard (see 6.21).

   The following syntactic forms, taken from [RFC 2234] or from
   2822], are repeated here for convenience only:

                          News Article Format                  July 2001

      ALPHA           = %x41-5A /          ; A-Z
                        %x61-7A            ; a-z
      CR              = %x0D               ; carriage return
      CRLF            = CR LF
      DIGIT           = %x30-39            ; 0-9
      HTAB            = %x09               ; horizontal tab
      LF              = %x0A               ; line feed
      SP              = %x20               ; space
      NO-WS-CTL       = %d1-8 /            ; US-ASCII control characters
                        %d11 /             ; which do not include the
                        %d12 /             ; carriage return, line feed,
                        %d14-31 /          ; and whitespace characters
      specials        = "(" / ")" /        ; Special characters used in
                        "<" / ">" /        ;  other parts of the syntax
                        "[" / "]" /
                        ":" / ";" /
                        "@" / "
                        "," / "." /
      WSP             = SP / HTAB          ; Whitespace characters
                          News Article Format                 April 2001
      FWS             = ([*WSP CRLF] 1*WSP); Folding whitespace
      ccontent        = ALPHA / DIGIT /
                        "!" ctext / "#" quoted-pair / comment
      comment         = "(" *([FWS] ccontent) [FWS] ")"
      CFWS            = *([FWS] comment) (([FWS] comment) / FWS )
      DQUOTE          = %d34              ; quote mark
      quoted-pair     = "\" text
      atext           = ALPHA / DIGIT /
                        "!" / "#" /        ; Any character except
                        "$" / "%" /        ; controls controls, SP, and specials.
                        "&" / "'" /        ; Used for atoms
                        "*" / "+" /
                        "-" / "/" /
                        "=" / "?" /
                        "^" / "_" /
                        "`" / "}" /
                        "|" / "}" /
      atom            = [CFWS] 1*atext [CFWS]
      dot-atom        = [CFWS] dot-atom-text [CFWS]
      dot-atom-text   = 1*atext *( "." 1*atext )
      comment         = "(" *([FWS]
                           (ctext / quoted-pair / comment)) [FWS] ")"
      qcontent        = *([FWS] comment) (([FWS] comment) qtext / FWS )
      DQUOTE          = %d34              ; quote mark quoted-pair     = "\" text
      quoted-string   = [CFWS]
                           DQUOTE *([FWS] (qtext / quoted-pair)) qcontent) [FWS] DQUOTE
      word            = atom / quoted-string
      phrase          = 1*word
      unstructured    = *( [FWS] utext ) [FWS]

        NOTE: CFWS occurs at many places in the syntax in order to allow
        comments and extra whitespace to be inserted almost anywhere.
        The syntax is in fact ambiguous insofar as it may be impossible
        to tell in which of several possible ways a given comment or WS
        was produced. However, this does not lead to semantic ambiguity
                          News Article Format                  July 2001

        because, unless specifically stated otherwise, the presence of
        absence of a comment or additional WS has no semantic meaning
        and, in particular, it is a matter of indifference whether it
        forms a part of the syntactic construct preceding it or the one
        following it.

        NOTE: Following [RFC 2234], literal text included in the syntax
        is to be regarded as case-insensitive.  However, in
        contradistinction to [MESSFOR], [RFC 2822], the Netnews protocols are
        sensitive to case in some instances (as in newsgroup names, some
        header parameters, etc.). Care has been taken to indicate this
        explicitly where required.

   The complete syntax defined in this standard is repeated, for
   convenience, in Appendix B.

2.5.  Language

   Various constant strings in this standard, such as header names and
   month names, are derived from English words. Despite their
   derivation, these words do NOT change when the poster or reader
   employing them is interacting in a language other than English.
   Posting and reading agents MAY translate as appropriate in their
   interaction with the poster or reader, but the forms that actually
                          News Article Format                 April 2001
   appear in articles MUST be the English-derived ones defined in this

3.  Changes to the existing protocols

   This standard prescribes many changes, clarifications and new
   features since the protocols described in [RFC 1036] and [Son-of-
   1036].  It is the intention that they can be assimilated into Usenet
   as it presently operates without major interruption to the service,
   though some of the new features may not begin to show benefit until
   they become widely implemented. This section summarizes the main
   changes, and comments on some features of the transition.

3.1.  Principal Changes

     o The [MESSFOR] [RFC 2822] conventions for parenthesis-enclosed comments in
       headers are supported.
     o Whitespace is permitted in Newsgroups headers, permitting folding
       of such headers. Indeed, all news headers can now be folded.
     o An enhanced syntax for the Path header enables the injection
       point of and the route taken by an article to be determined with
     o Netnews is firmly established as an 8bit medium.
     o Large parts of MIME are recognised as an integral part of
     o The charset for headers is always UTF-8. This will, inter alia,
       permit newsgroup-names with non-ASCII characters.
     o There is a new Control command 'mvgroup' to facilitate moving a
       group to a different place (name) in a hierarchy.
     o There are several new headers defined, such as Replaces and
                          News Article Format                  July 2001

       Author-Ids, leading to increased functionality.
     o There are numerous other small changes, clarifications and
[Doubtless many other changes should be listed, but there is little
point in doing so until our text is nearing completion. The above gives
the flavour of what should be said. There should also be references to
Appendix A.3 and Appendix A.4 ]

3.2.  Transitional Arrangements

   An important distinction must be made between serving and relaying
   agents which are responsible for the distribution and storage of news
   articles, and user agents which are responsible for interactions with
   users. It is important that the former should be upgraded to conform
   to this standard as soon as possible to provide the benefit of the
   enhanced facilities.  Fortunately, the number of distinct
   implementations of such agents is rather small, at least so far as
   the main "backbone" of Usenet is concerned, and many of the new
   features are already supported. Contrariwise, there are a great
   number of implementations of user agents, installed on a vastly
   greater number of small sites. Therefore, the new functionality has
   been designed so that existing agents may continue to be used,
   although the full benefits may not be realised until a substantial
   proportion of them have been upgraded.

                          News Article Format                 April 2001

   In the list which follows, care has been taken to distinguish the
   implications for both kinds of agent.

     o [MESSFOR] [RFC 2822] style comments in headers do not affect serving and
       relaying agents (note that the Newsgroups and Path headers do not
       contain them). They are unlikely to hinder their proper display
       in existing user agents except in the case of the References
       header in agents which thread articles. Therefore, it is provided
       that they SHOULD NOT be generated except where permitted by the
       previous standards.
     o Because of its importance to all serving agents, the extension
       permitting whitespace and folding in Newsgroup headers SHOULD NOT
       be used until it has been widely deployed amongst relaying
       agents. User agents are unaffected.
     o The new style of Path header is already consistent with the
       previous standards. However, the intention is that relaying
       agents should eventually reject articles in the old style, and so
       this should be offered as a configurable option for relaying
       agents. User agents are unaffected.
     o The vast majority of serving, relaying and transport agents are
       believed to be already 8bit clean (in the slightly restricted
       sense in which that term is used in the MIME standards). User
       agents that do not implement MIME may be disadvantaged, but no
       more so than at present when faced with 8bit characters (which
       currently abound in spite of the previous standards).
     o The introduction of MIME reflects a practice that is already
       widespread.  Articles in strict compliance with the previous
       standards (using strict US-ASCII) will be unaffected. Many user
       agents already support it, at least to the extent of widely used
                          News Article Format                  July 2001

       charsets such as ISO-8859-1. Users expecting to read articles
       using the more exotic other charsets will need to acquire suitable reading
       agents. It is not intended, in general, that any single user
       agent will be able to display every charset known to IANA, but
       all such agents MUST support US-ASCII. Serving and relaying
       agents are not affected.
     o The use of the UTF-8 charset for headers will not affect any
       existing usage, since US-ASCII is a strict subset of UTF-8.
       Insofar as newsgroup names containing non-ASCII characters can
       now be expected to arise, support from serving and relaying
       agents will be necessary. It is believed that the customary
       storage structure used by serving agents can already cope
       (perhaps not ideally) with such names. Note that it is not
       necessary for serving and relaying agents to understand all the
       characters available in UTF-8, though it is desirable for them to
       be displayable for diagnostic purposes via some escape mechanism
       using, for example, the visible subset of US-ASCII. For users
       expecting to use the more exotic charsets possibilities available under
       UTF-8, the remarks already made in connection with MIME will
     o The new Control: mvgroup command will need to be implemented in
       serving agents. It SHOULD be used in conjunction with pairs of
       matching rmgroup and newgroup commands (injected shortly after
       the mvgroup) until such time as mvgroup is widely implemented.
       The new Replaces header is also effectively a Control command,
       and transitional arrangements are provided which should be used
                          News Article Format                 April 2001
       in the meantime. User agents are unaffected.
     o The headers newly introduced by this standard can safely be
       ignored by existing software, albeit with loss of the new

4.  Basic Format

4.1.  Syntax of News Articles

   The overall syntax of a news article is:

      article           = 1*header separator body
      header            = header-name ":" 1*SP header-content CRLF
      header-name       = 1*name-character *( "-" 1*name-character )
      name-character    = ALPHA / DIGIT
      header-content    = USENET-header-content
                               *( [CFWS] ";" header-parameter ) /
                        = <the header-content defined in this standard
                           (or an extension of it) for a specific
                           USENET header>
                        = <a header-content defined (explicitly or
                           implicitly) by some other standard>
      header-parameter  = USENET-header-parameter /
                          News Article Format                  July 2001

                        = <an other-header-parameter defined in
                           this standard for use in conjunction with
                           a specific USENET-header-content>
                        = attribute "=" value
      attribute         = USENET-token / iana-token / x-token
      value             = token / quoted-string
      USENET-token      = <A token defined in this standard for
                           use in conjunction with a specific
      iana-token        = <A token defined in an experimental
                           or standards-track RFC and registered with
      x-token           = [CFWS] "x-" token-core [CFWS]
      token             = [CFWS] token-core [CFWS]
      token-core        = 1*<any (US-ASCII) CHAR except SP, CTLs,
                                    or tspecials>
      tspecials         = "(" / ")" / "<" / ">" / "@" /
                          "," / ";" / ":" / "\" / DQUOTE /
                          "/" / "[" / "]" / "?" / "="
      separator         = CRLF
      body              = *( *998text CRLF )

   An article consists of some headers followed by a body. An empty line
   separates the two. The headers contain structured information about
   the article and its transmission. A header begins with a header-name
                          News Article Format                 April 2001
   identifying it, and can be continued onto subsequent lines as
   described in section 4.2.3.  The body is largely unstructured text
   significant only to the poster and the readers.

        NOTE: Terminology here follows the current custom in the news
        community, rather than the [MESSFOR] [RFC 2822] convention of referring to
        what is here called a "header" as a "header-field" or "field".

   Note that the separator line must be truly empty, not just a line
   containing white space. Further empty lines following it are part of
   the body, as are empty lines at the end of the article.

        NOTE: The syntax above defines the canonical form of a news
        article as a sequence of lines each terminated by CRLF. This
        does not prevent serving agents or transport agents from storing
        or handling the article in other formats (e.g. using a single LF
        in place of CRLF) so long as the overall effects achieved are as
        defined by this standard when operating on the canonical form.

4.2.  Headers

4.2.1.  Names and Contents

   Despite the restrictions on header-name syntax imposed by the
   grammar, relayers and reading agents SHOULD tolerate header names
   containing any US-ASCII printable character other than colon (":",
   US-ASCII 58).
[To bring it into line with <optional-field> as given in [MESSFOR].]

                          News Article Format                  July 2001

   Header-names SHOULD be either those for which a USENET-header-content
   is defined in established by this standard, or those defined in [MESSFOR], by [RFC 2822], or those
   defined in by any
   extension to either of these standards including, in particular, the Mime
   MIME standards [RFC 2045] et seq., or else experimental headers
   beginning with "X-" (as defined in  Software SHOULD NOT
   attempt to interpret headers not described in this standard or in its
   extensions, but relaying agents MUST pass them on unaltered and
   reading agents MUST enable them to be displayed, at least optionally.

   The possibility of allowing header-parameters to appear in all
   headers is provided mainly for the purpose of allowing future
   extensions to existing headers, since only a very few USENET-header-
   parameters are actually defined in this standard. Observe that such
   header-parameters do not, in general, occur in headers defined in
   other standards, except for the Mime MIME standards [RFC 2045] et seq. and
   their extensions. Nevertheless, compliant software MUST accept all
   such header-parameters in headers defined by this standard and its
   extensions (ignoring them if their meaning is unknown) and SHOULD
   accept (and ignore) them in all headers.
[but what about
address = mailbox / group
group = phrase ":" [mailbox-list] ";"
Does the following NOTE cover the situation?]
                          News Article Format                 April 2001

        NOTE: The presence of a ";" in a header-content does not
        indicate the presence of a header-parameter in the few
        situations where it can be parsed as part of some USENET-
        header-content or other-header-content.

   On the other hand, posting agents SHOULD NOT generate them header-
   parameters (even those using x-tokens) except in those headers for
   which a USENET-
   header-parameter USENET-header-parameter has been defined, or where that usage
   is permitted by some other standard (notably one of the Mime MIME
   standards). This restriction is likely to removed in a future version
   of this standard.

        NOTE: The given syntax is ambiguous insofar as a USENET-header-
        content that is defined to be <unstructured> could contain,
        within that <unstructured>, text of the form <*(";" header-
        parameter)>. The intention is therefore that any such apparent
        header-parameters are to be regarded as part of the
        <unstructured>. This standard therefore does not (and extensions
        to it SHOULD NOT) define any USENET-header-parameter to be
        associated with such an unstructured USENET-header-content.

   The order of headers in an article is not significant. However,
   posting agents are encouraged to put mandatory headers (section 5)
   first, followed by optional headers (section 6), followed by
   experimental headers and headers not defined in this standard or its
   extensions. Relaying agents MUST NOT change the order of the headers
   in an article, though they MAY add additional headers (notablt local
   headers (, preferably either before or after all the existing
   ones. article.

                          News Article Format                  July 2001

   Header-names are case-insensitive. There is a preferred case
   convention, which posters and posting agents SHOULD Ought to use: each
   hyphen-separated "word" has its initial letter (if any) in uppercase
   and the rest in lowercase, except that some abbreviations have all
   letters uppercase (e.g. "Message-ID" and "MIME-Version"). The forms
   used in this standard are the preferred forms for the headers
   described herein. Relaying and reading agents MUST, however, tolerate
   articles not obeying this convention.

4.2.2.  Header Properties

   There are four three special properties that may apply to particular
   headers, namely: "experimental", "inheritable", "local", and "variant". When a
   header is defined, in this (or any future) standard, as having one
   (or possibly more) of these properties, it is subject to special
   treatment, as indicated below.  Experimental Headers

   Experimental headers are those whose header-names begin with "X-".
   They are to be used for experimental Netnews features, or for
   enabling additional material to be propagated with an article. There
   are no established headers (see 4.2.1) that are considered
   experimental headers; an established header cannot be experimental.

                          News Article Format                 April 2001

        NOTE: Some such headers may eventually be adopted as standard by
        some extension to this standard, at which point they will lose
        their "X-" prefix.  Inheritable Headers

   Subject only to the overriding ability of the poster to determine the
   contents of the headers in a proto-article, headers with the
   inheritable property MUST be copied by followup agents (perhaps with
   some modification) into the followup article, and headers without
   that property MUST NOT be so copied.  Examples include:
     o Newsgroups (5.5) - copied from the precursor, subject to any
       Followup-To header.
     o Subject (5.4) - modified by prefixing with "Re: ", but otherwise
       copied from the precursor.
     o References (6.10) - copied from the precursor, with the addition
       of the precursor's Message-ID.
     o Distribution (6.6) - copied from the precursor.

        NOTE: The Keywords header is not inheritable, though some older
        newsreaders treated it as such.  Local  Variant Headers

   Headers with the local variant property may differ between (or even be
   completely absent from) copies of the same article as stored or
   relayed throughout a Netnews system. The manner of the difference (or
   absence) MUST be as specified in this (or any future) standard.
   Typically, these headers are significant only to modified as articles are propagated, or
                          News Article Format                  July 2001

   they reflect the status of the article on a particular serving agent (or perhaps a agent,
   or cooperating group of such agents). They
   MAY be removed by relaying agents before propagation, and MUST be
   removed (and replaced as necessary) by serving agents when received. agents. The replaced variant header MAY be placed
   anywhere within the headers (though placing it first is recommended).
   The principle example is: examples are:
     o Path (5.6) - augmented at each relaying agent that an article
       passes through.
     o Xref (6.16) - used to keep track of the article locators of
       crossposted articles so that newsreaders serviced by a particular
       serving agent can mark such articles as read.  Variant Headers

   Headers with the variant property are modified as articles are
   propagated. The modified header MAY be placed anywhere within the
   headers (though placing it first is recommended). The principle
   example is:
     o Path (5.6) - augmented at each relaying agent that an article
       passes through.

4.2.3.  White Space and Continuations

[The following text is taken from [MESSFOR], adapted to the different
terminology used for this standard.]

   Each header is logically a single line of characters comprising the
   header-name, the colon with its following SP, and the header-content.
   For convenience, however, the header-content can be split into a
   multiple line representation; this is called "folding". The general
   rule is that wherever this standard allows for FWS or CFWS (but not
   simply SP or HTAB) a CRLF may be inserted before any WSP. For
                          News Article Format                 April 2001
   example, the header:
      Approved: modname@modsite.example (Moderator of
   can be represented as:
      Approved: modname@modsite.example
         (Moderator of

        NOTE: Though header-contents are defined in such a way that
        folding can take place between many of the lexical tokens (and
        even within some of them), folding SHOULD be limited to placing
        the CRLF at higher-level syntactic breaks, and SHOULD also avoid
        leaving trailing WSP on the preceding line. For instance, if a
        header-content is defined as comma-separated values, it is
        recommended that folding occur after the comma separating the
        structured items, even if it is allowed elsewhere.

   Folding MUST NOT be carried out in such a way that any line of a
   header is made up entirely of WSP characters and nothing else.

   The colon following the header name on the first line MUST be
   followed by a WSP, even if the header is empty. If the header is not
   empty, at least some of the content MUST appear on the first line
   (this is to avoid the possibility of harm by any non-compliant agent
   that might eliminate a trailing SP). Posting agents MUST enforce
   these restrictions, but relaying agents SHOULD accept even articles
   that violate them.

        NOTE: This standard differs from [MESSFOR] [RFC 2822] in requiring that
        WSP followng the colon (it was also an [RFC 1036] requirement).

   Posters and posting agents SHOULD use SP, not HTAB, where white space
   is desired in headers (some existing software expects this), and MUST
   use SP immediately following the colon after a header-name. Relaying
   agents SHOULD accept HTAB in all such cases, however.

                          News Article Format                  July 2001

   Since the white space beginning a continuation line remains a part of
   the logical line, headers can be "broken" into multiple lines only at
   FWS or CFWS. Posting agents Ought Not to break headers unnecessarily
   (but see 4.5 4.5).


   Strings of characters which are treated as comments may be included
   in header-contents wherever the syntactic element CFWS occurs. They
   consist of characters enclosed in parentheses. Such strings are
   considered comments so long as they do not appear within a quoted-
   string. Comments may be nested.

   A comment is normally used to provide some human readable
   informational text, except at the end of an address which contains no
   phrase, as in (Fred Bloggs)
   as opposed to
      "Fred Bloggs" <> .

                          News Article Format                 April 2001

   The former is a deprecated, but commonly encountered, usage and
   reading agents SHOULD take special note of such comments as
   indicating the name of the person whose address it is. In all other
   situations a comment is semantically interpreted as a single SP.
   Since a comment is allowed to contain FWS, folding is permitted
   within it as well as immediately preceding and immediately following
   it. Also note that, since quoted-pair is allowed in a comment, the
   parenthesis and backslash characters may appear in a comment so long
   as they appear as a quoted-pair. Semantically, the enclosing
   parentheses are not part of the comment content; the content is what
   is contained between the two parentheses.

   Since comments have not hitherto been permitted in news articles,
   except in a few specified places, posters and posting-agents SHOULD
   NOT insert them except in those places, namely following addresses in
   From and similar headers, and to indicate the name of the timezone in
   Date headers.  However, compliant software MUST accept them in all
   places where they are syntactically allowed.

4.2.5.  Undesirable Headers

   A header whose content is empty is said to be an empty header.
   Relaying and reading agents SHOULD NOT consider presence or absence
   of an empty header to alter the semantics of an article (although
   syntactic rules, such as requirements that certain header names
   appear at most once in an article, MUST still be satisfied). Posting
   and injecting agents SHOULD delete empty headers from articles before
   posting them; relaying agents MUST pass them untouched.

   Headers that merely state defaults explicitly (e.g., a Followup-To
   header with the same content as the Newsgroups header, or a Mime MIME
   Content-Type header with contents "text/plain; charset=us-ascii") or
   state information that reading agents can typically determine easily
   themselves (e.g.  the length of the body in octets) are redundant and
                          News Article Format                  July 2001

   posters and posting agents Ought Not to include them.

4.3.  Body

4.3.1.  Body Format Issues

   The body of an article SHOULD NOT be empty. A posting or injecting
   agent which does not reject such an article entirely SHOULD at least
   issue a warning message to the poster and supply a non-empty body.
   Note that the separator line MUST be present even if the body is

        NOTE: Some existing news software is known to react badly to
        body-less articles, hence the request for posting and injecting
        agents to insert a body in such cases. The sentence "This
        article was probably generated by a buggy news reader" has
        traditionally been used is this situation.

                          News Article Format                 April 2001

   Note that an article body is a sequence of lines terminated by CRLFs,
   not arbitrary binary data, and in particular it MUST end with a CRLF.
   However, relaying agents SHOULD treat the body of an article as an
   uninterpreted sequence of octets (except as mandated by changes of
   CRLF representation and by control-message processing) and SHOULD
   avoid imposing constraints on it. See also section 4.5.

   Posters SHOULD avoid using control characters and escape sequences
   except for tab (ASCII (US-ASCII 9), formfeed (ASCII (US-ASCII 12) and, possibly,
   backspace (ASCII (US-ASCII 8).  Tab signifies sufficient horizontal white
   space to reach the next of a set of fixed positions; posters are
   warned that there is no standard set of positions, so tabs should be
   avoided if precise spacing is essential. Formfeed (which is sometimes
   referred to as the "spoiler character") signifies a point at which a
   reading agent Ought to pause and await reader interaction before
   displaying further text. Reading agents MUST NOT pass

        NOTE: Passing other control characters or escape sequences
        unaltered to an output device. a display or printing device is likely to have
        unpredictable results, except in the case of a device adapted to
        the special needs of some particular character set.

        NOTE: Backspace was historically used for underlining, done by
        an underscore (ASCII (US-ASCII 95), a backspace, and a character,
        repeated for each character that should be underlined. Posters
        are warned that underlining is not available on all output
        devices or supported by all reading agents and is best not
        relied on for essential meaning.

4.3.2.  Body Conventions

   A body is by default an uninterpreted sequence of octets for most of
   the purposes of this standard. However, a Mime MIME Content-Type header
   may impose some structure or intended interpretation upon it, and may
   also specify the character set in accordance with which the octets
   are to be interpreted.

                          News Article Format                  July 2001

   It is a common practice for followup agents to enable the
   incorporation of the followed-up article (the "precursor") as a
   quotation. This SHOULD be done by prefacing each line of the quoted
   text (even if it is empty) with the character ">" (or perhaps with
   "> " in the case of a previously unquoted line). This will result in
   multiple levels of ">" when quoted content itself contains quoted
   content, and it will also facilitate the automatic analysis of

        NOTE: Posters should edit quoted context to trim it down to the
        minimum necessary. However, followup agents Ought Not to attempt
        to enforce this beyond issuing a warning (past attempts to do so
        have been found to be notably counter-productive).

   The followup agent SHOULD also precede the quoted content by an
   "attribution line" (however, readers are warned not to assume that
   they are accurate, especially within multiply nested quotations). The
   following convention for such lines, whilst not mandated by this
   standard, is intended to facilitate their automatic recognition and
   processing by sophisticated reading agents. The attribution SHOULD
   contain the name or the email address of the precursor's poster, as
                          News Article Format                 April 2001
      Joe D. Bloggs <jdbloggs@foo.example> wrote:
      Helmut Schmidt <helmut@bar.example> schrieb:

   The attribution MAY contain also a single Newsgroup name (the one
   from which the followup is being made), the precursor's Message-ID
   and/or the precursor's Date and Time. Any of these that are present,
   SHOULD precede the name and/or email address. However, the inclusion
   or not of such fields Ought always to be under the control of the

   To enable this line, and the Message-ID and the Email address within
   it, to be recognised (for example to enable suitable reading agents
   to retrieve the precursor or email its poster by clicking on them),
   the following conventions SHOULD be observed:
     o The precursor's Message-ID SHOULD be enclosed within <...> or
     o The precursor's poster's Email address SHOULD be enclosed within
     o The various fields may be separated by arbitrary text and they
       may be folded in the same way as headers, but attributions SHOULD
       always be terminated by a ":" followed by CRLF.

   Further examples:

      On in <1234@bar.example> on 24 Dec 1997 16:40:20 +0000,
         Joe D. Bloggs <jdbloggs@bar.example> wrote:

      Am 24. Dez 1997 schrieb Helmut Schmidt <helmut@bar.example>:

                          News Article Format                  July 2001

   A "personal signature" is a short closing text automatically added to
   the end of articles by posting agents, identifying the poster and
   giving his network addresses, etc. If a poster or posting agent does
   append such a signature to an article, it MUST be preceded with a
   delimiter line containing (only) two hyphens (ASCII (US-ASCII 45) followed
   by one SP (ASCII (US-ASCII 32). The signature is considered to extend from
   the last occurrence of that delimiter up to the end of the article
   (or up to the end of the part in the case of a multipart Mime MIME body).
   Followup agents, when incorporating quoted text from a precursor,
   Ought Not to include the signature in the quotation. Posting agents
   Ought to discourage (at least with a warning) signatures of excessive
   length (4 lines is a commonly accepted limit).

4.4.  Characters and Character Sets

   Transmission paths for news articles MUST treat news articles as
   uninterpreted sequences of octets, excluding the values 0 (ASCII (US-ASCII
   NUL) and 13 and 10 (ASCII (US-ASCII CR and LF, which MUST ONLY appear in the
   combination CRLF which denotes a line separator).

        NOTE: this correspponds to the range of octets permitted for
        MIME "8bit data" [RFC 2045].  Thus raw binary data cannot be
        transmitted in an article body except by the use of a Content-
                          News Article Format                 April 2001
        Transfer-Encoding such as base64.

   Character data is represented by octets in accordance with some
   encoding scheme (UTF-8 for headers, and determined by the Content-
   Type and Content-Transfer-Encoding headers for bodies).

   If it comes to a relaying agent's attention that it is being asked to
   pass an article using the Content-Transfer-Encoding "8bit" to a
   relaying agent that does not support it, it SHOULD report this error
   to its administrator. It MUST refuse to pass the article and MUST NOT
   re-encode it with different Mime MIME encodings.

        NOTE: This strategy will do little harm. The target relaying
        agent is unlikely to be able to make use of the article on its
        own servers, and the usual flooding algorithm will likely find
        some alternative route to get the article to destinations where
        it is needed.

4.4.1.  Character Sets within Article Headers

   Within article headers, characters are represented as octets
   according to the UTF-8 encoding scheme [ISO 10646] or [RFC 2279] or [ISO/IEC 10646],
   and hence all the characters in Unicode [UNICODE 3.1] or in the
   Universal Multiple-Octet Coded Character Set (UCS) [ISO [ISO/IEC 10646]
   (which is essentially a superset of Unicode [UNICODE] and expected to remain
   so) are potentially available. However, interpreting the processing all octets directly in the
   same manner as US-ASCII characters should ensure correct behaviour in
   most situations.

                          News Article Format                  July 2001

        NOTE: UTF-8 is an encoding for 16bit (and even 32bit) character
        sets with the property that any octet less than 128 immediately
        represents the corresponding US-ASCII character, thus ensuring
        upwards compatibility with previous practice.  Non-ASCII
        characters from UCS Unicode are represented by sequences of octets
        satisfying the syntax of a UTF8-xtra-char (2.4).  Only those (2.4), which excludes
        certain octet sequences not explicitly permitted by [RFC 2044] shall be
        used.  UCS 2279].
        Unicode includes all characters from the ISO-8859 series of
        characters sets [ISO 8859] (which includes all Cyrillic, Greek
        and Arabic characters) as well as together with the more elaborate
        characters used in
        Japan and China. Asian countries. See the following section
        for the appropriate treatment of UCS Unicode characters by reading

   Notwithstanding the great flexibility permitted by UTF-8, there is
   need for restraint in its use in order that the essential components
   of headers may be discerned using reading agents that cannot present
   the full UCS Unicode range. In particular, header-names and tokens MUST
   be in US-ASCII, and certain other components of headers, as defined
   elsewhere in this standard - notably msg-ids, date-times, dot-atoms,
   domains and path-identities - MUST be in US-ASCII.  Comments, phrases
   (as in addresses) and unstructureds (as in Subject headers) MAY use
   the full range of UTF-8 characters. For characters, but SHOULD nevertheless be
   invariant under Unicode normalization NFC [UNICODE 3.1].

        NOTE: The effect of normalization NFC is to place composite
        characters (made by overlaying one character with another) into
        a canonical form (usually represented by a single character
        where one is available - thus E-acute is preferred over E
        followed by a non-spacing acute accent), and to make a
        consistent choice among equivalent forms (e.g. the Angstrom sign
        is replaced by A-ring). At least for the main European
        languages, for which all the needed composites are already
        available as single characters, it is unlikely that posting
        agents will need to take any special steps to ensure

   In the particular case of newsgroup-names see 5.5. (see 5.5) there are more
   stringent requirements regarding the use of UTF-8 and Unicode.

   Where the use of non-ASCII characters, encoded in UTF-8, is permitted
   as above, they MAY also be encoded using the Mime MIME mechanism defined
   in [RFC 2047], but this usage is deprecated within news articles
                          News Article Format                 April 2001
   (even though it is required in mail messages) since it is less
   legible in older reading agents which support neither it nor UTF-8.
   Nevertheless, reading agents SHOULD support this usage, but only in
   those contexts explicitly mentioned in [RFC 2047].

4.4.2.  Character Sets within Article Bodies

   Within article bodies, characters are represented as octets according
   to the encoding scheme implied by any Content-Transfer-Encoding and
   Content-Type headers [RFC 2045].  In the absence of such headers,
   reading agents cannot be relied upon to display correctly more than
                          News Article Format                  July 2001

   the US-ASCII characters.

        NOTE: Observe that reading agents are not forbidden to "guess",
        or to interpret as UTF-8 regardless, which would be the simplest
        course for them to take.

        NOTE: It is not expected that reading agents will necessarily be
        able to present characters in all possible character sets,
        although they MUST be able to present all US-ASCII characters.
        For example, a reading agent might be able to present only the
        ISO-8859-1 (Latin 1) characters [ISO 8859], in which case it
        Ought to present undisplayable characters using some distinctive
        glyph, or by exhibiting a suitable warning. Older reading agents
        that do not understand Mime MIME headers or UTF-8 should be able to
        display bodies in US-ASCII (with some loss of human
        comprehensibility) except possibly when the Content-Transfer-
        Encoding is "8bit".

   Followup agents MUST be careful to apply appropriate encodings to the
   outbound followup. A followup to an article containing non-ASCII
   material is very likely to contain non-ASCII material itself.

4.5.  Size Limits

   Posting agents SHOULD endeavour to keep all header lines, so far as
   is possible, within 79 characters by folding them at suitable places
   (see 4.2.3).  However, posting agents MUST permit the poster to
   include longer headers if he so insists, and compliant software MUST
   support headers of at least 998 octets. Likewise, injecting agents
   SHOULD fold any headers generated automatically by themselves.
   Relaying agents MUST NOT fold headers (i.e. they must pass on the
   folding as received).

        NOTE: There is NO restriction on the number of lines into which
        a header may be split, and hence there is NO restriction on the
        total length of a header (in particular it may, by suitable
        folding, be made to exceed the 998 octets restriction pertaining
        to a single header line).

   The syntax provides for the lines of a body to be up to 998 octets in
   length, not including the CRLF. All software compliant with this
   standard MUST support lines of at least that length, both in headers
   and in bodies, and all such software SHOULD support lines of
                          News Article Format                 April 2001
   arbitrary length. In particular, relaying agents MUST transmit lines
   of arbitrary length without truncation or any other modification.

        NOTE: The limit of 998 octets is consistent with the
        corresponding limit in [MESSFOR].
[RFC8222? now expresses it as 1000 incl. CRLF] [RFC 2822].

   In plain-text messages (those with no Mime MIME headers, or those with a
   MIME Content-Type of text/plain) posting agents Ought to endeavour to
   keep the length of body lines within some reasonable limit. The size
   of this limit is a matter of policy, the default being to keep within
   79 characters at most, and preferably within 72 characters (to allow
                          News Article Format                  July 2001

   room for quoting in followups).  Exceptionally, posting agents Ought
   Not to adjust the length of quoted lines in followups unless they are
   able to reformat them in a consistent manner.  Moreover, posting
   agents MUST permit the poster to include longer lines if he so

        NOTE: Plain-text messages are intended to be displayed "as-is"
        without any special action (such as automatic line splitting) on
        the part of the recipient. The policy limit (e.g. 72 or 79)
        should be expressed as a number of characters (as they will be
        displayed by a reading agent) rather than as the number of
        octets used to encode them.

        NOTE: This standard provides no upper bound on the overall size
        of a single article, but neither does it forbid relaying agents
        from dropping articles of excessive length. It is, however,
        suggested that any limits thought appropriate by particular
        agents would be more appropriately expressed in megabytes than
        in kilobytes.

4.6.  Example

   Here is a sample article:

      Path: server.example/unknown.site2.example@site2.example/
      Newsgroups: example.announce,
      Message-ID: <9urrt98y53@site.example>
      From: Ann Example <a.example@site1.example>
      Subject: Announcing a new sample article.
      Date: Fri, 27 Mar 1998 12:12:50 +1300
      Approved: example.announce moderator <jsmith@site.example>
      Reply-To: Ann Example <a.example+replies@site1.example>
      Expires: Wed, 22 Apr 1998 12:12:50 -0700
      Organization: Site1, The Number one site for examples.
      User-Agent: ExampleNews/3.14 (Unix)
      Keywords: example, announcement, standards, RFC 1036, Usefor
      Summary: The URL for the next standard.

      Just a quick announcemnt that a new standard example article has
                          News Article Format                 April 2001
      been released; it is in the new USEFOR draft obtainable from

      Ann Example <a.example@site1.example>   Sample Poster to the Stars
      "The opinions in this article are bloody good ones" - J. Clarke.

                          News Article Format                  July 2001

5.  Mandatory Headers

   An article MUST have one, and only one, of each of the following
   headers: Date, From, Message-ID, Subject, Newsgroups, Path.

   Note also that there are situations, discussed in the relevant parts
   of section 6, where References, Sender, or Approved headers are
   mandatory. In control messages, specific values are required for
   certain headers.

   For the overall syntax of headers, see section 4.1.  In the
   discussions of the individual headers, the content of each is
   specified using the syntax notation. The convention used is that the
   content of, for example, the Subject header is defined as <Subject-

   A proto-article (see 8.2.1) may lack some of these mandatory headers,
   but they MUST then be supplied by the injecting agent.

5.1.  Date

   The Date header contains the date and time that the article was
   prepared by the poster ready for transmission and SHOULD express the
   poster's local time. The content syntax makes use of syntax defined
   in [MESSFOR]. [RFC 2822], subject to the following revised definition of zone.

      Date-content        = date-time

        NOTE: It
      zone                = (( "+" / "-" ) 4DIGIT) / "UT" / "GMT"

   The forms "UT" and "GMT" (indicating universal time) are to be
   regarded as obsolete synonyms for "+0000". They MUST be be accepted,
   and passed on unchanged, by all agents, but they MUST NOT be
   generated as part of new articles by posting and injecting agents.
   Although folding white space is permitted throughout the date-time
   syntax, it is RECOMMENDED that a useful single space be used in each place
   that FWS appears (whether it is required or optional).

        NOTE: A convention that is sometimes followed is to follow the date-time with add a
        comment, after the date-time, containing the time zone in
        human-readable form. The use form, but many of folding in a date-time is deprecated, even though permitted the abbreviations commonly used
        for this purpose are ambiguous. The value given by [MESSFOR].
[There the <zone> is a specific RECOMMENDED about this in MESSFOR now.]
        the only definitive form.

   In order to prevent the reinjection of expired articles into the news
   stream, relaying and serving agents MUST refuse articles whose Date
   header predates the earliest articles of which they normally keep
   record, or which is more than 24 hours into the future (though they
   MAY use a margin less than that 24 hours). Relaying agents MUST NOT
   modify the Date header in transit.

                          News Article Format                  July 2001

5.1.1.  Examples

      Date: Fri, 2 Apr 1999 20:20:51 -0500 (EST)
      Date: 26 May 1999 16:13 +0000
                          News Article Format                 April 2001
      Date: 26 May 1999 16:13 GMT (Obsolete)

5.2.  From

   The From header contains the electronic address(es), and possibly the
   full name, of the article's author(s). poster(s). The content syntax makes use
   of syntax defined in [MESSFOR], [RFC 2822], subject to the following revised
   definition of local-part.

      From-content        = mailbox-list
      addr-spec           = local-part "@" domain
      local-part          = dot-atom / strict-quoted-string

        NOTE: This syntax ensures that the local-part of an addr-spec is
        restricted to pure US-ASCII (and is thus in strict compliance
        with [MESSFOR]), [RFC 2822]), whilst allowing any UTF-8 character to be used
        in a preceding quoted-string containing the author's poster's full name.
        If some future extension to the Mail protocols should relax this
        restriction, one would expect the Netnews protocols to follow.

   The mailbox in the From-content SHOULD be a valid address, belonging
   to the poster(s) of the article, or person or agent on whose behalf
   the post is being sent (see the Sender header, 6.2).  When, for
   whatever reason, the poster does not wish to include such an
   adddress, the From-content SHOULD then be an address which ends in
   the top level domain of ".invalid" [RFC 2606].

        NOTE: Since such addresses ending in ".invalid" are
        undeliverable, user agents Ought to warn any user attempting to
        reply to them and Ought Not, in any case, to attempt to deliver
        to them (since that would be pointless anyway).  Whether or not
        a valid address can subsequently be extracted from such an
        address falls outside the scope of this standard (though it
        would be pointless to use a disguise so easily penetrable).

        Be warned also that some injecting agents that have
        authentication information may choose to replace the From-
        content based upon the authenticated identity.

5.2.1.  Examples:

      From: John Smith <jsmith@site.example>
      From: "John Smith" <jsmith@site.example>, dave@isp.example
      From: "John D. Smith" <jsmith@site.example>, andrew@isp.example,
      From: Jan Jones <jan@please_setup_your_system_correctly.invalid>
      From: Jan Jones <joe@guess-where.invalid>
      From: dave@isp.example (Dave Smith)
                          News Article Format                  July 2001

        NOTE: the last example shows a now deprecated convention of
        putting an author's a poster's full name in a comment following the mailbox,
        rather than in a phrase at the start of that mailbox. Observe
        that the quotes around the "John D. Smith" example were
        required, on account of the '.' character, and they would also
        have been required had any UTF8-xtra-char been present.

                          News Article Format                 April 2001

5.3.  Message-ID

   The Message-ID header contains the article's message identifier, a
   unique identifier distinguishing the article from every other
   article. The content syntax makes use of syntax defined in [MESSFOR], [RFC
   2822], subject to the following revised definition of no-fold-quote. no-fold-quote
   and no-fold-literal.

      Message-ID-content = msg-id
      id-left            = dot-atom-text / no-fold-quote
      id-right           = dot-atom-text / no-fold-literal
      no-fold-quote      = DQUOTE *( strict-qtext / strict-quoted-pair )
      no-fold-literal    = DQUOTE *( dtext / strict-quoted-pair ) DQUOTE

   A msg-id MUST NOT contain any SP within any strict-quoted-pair.  The
   msg-id MUST NOT be more than 250 octets in length.

        NOTE: The syntax ensures that a msg-id is restricted to pure
        US-ASCII (and
        US-ASCII, and is thus in a strict compliance subset of that defined by [RFC
        2822].  The exclusion of SP is to ensure compatibility with [MESSFOR]).
        existing software.  The length restriction ensures that systems
        which accept message identifiers as a parameter when retrieving
        an article (e.g. [NNTP]) can rely on a bounded length. Observe
        that msg-id includes the '<' and '>'.
[Do something about whitespace in dot-atom-text and no-fold-quote.]

   Following the provisions of [MESSFOR], [RFC 2822], an agent generating an
   article's message identifier MUST ensure that it is unique and that
   it is NEVER reused (either in Netnews or email). Moreover, even
   though commonly derived from the domain name of the originating site
   (and domain names are case-insensitive), a message identifier MUST
   NOT be altered in any way during transport, or when copied (as into a
   References header), and thus a simple (case-sensitive) comparison of
   octets will always suffice to recognise that same message identifier
   wherever it subsequently reappears.

        NOTE: some old software may treat message identifiers that
        differ only in case within their id-right part as equivalent,
        and implementors of agents that generate message identifiers
        should be aware of this.

5.4.  Subject

   The Subject header contains a short string identifying the topic of
   the message. This is an inheritable header ( to be copied
   into the Subject header of any followup, in which case the new
   header-content SHOULD then default to the string "Re: " (a "back
                          News Article Format                  July 2001

   reference") followed by the contents of the pure-subject of the
   precursor. Any leading "Re: " in the pure-subject MUST be stripped.

      Subject-content     = [ back-reference ] pure-subject
      pure-subject        = 1*( [FWS] utext )
      back-reference      = %x52.65.3A.20
                                    ; which is a case-sensitive "Re: "

   The pure-subject MUST NOT begin with "Re: ".

                          News Article Format                 April 2001

        NOTE: The given syntax differs from that prescribed in [MESSFOR] [RFC
        2822] insofar as it does not permit a header content to be
        completely empty, or to consist of WSP only (see remarks in
        4.2.5 concerning undesirable headers).

   Followup agents MAY remove instances of non-standard strings that are known to be used
   erroneously as back-reference (such as "Re(2): ", "Re:", "RE: ", or
   "Sv: ") from the Subject-
   content Subject-content when composing the subject of a
   followup and add a correct back-reference in front of the result.

        NOTE: that would be "SHOULD remove instances" except that we
        cannot find a sufficiently robust and simple algorithm to do the
        necessary natural language processing.

   Followup agents MUST NOT use any other string except "Re: " as a back
   reference. Specifically, a translation of "Re: " into a local
   language or usage MUST NOT be used.

        NOTE: "Re" is an abbreviation for the Latin "In re", meaning "in
        the matter of", and not an abbreviation of "Reference" as is
        sometimes erroneously supposed.

   Agents SHOULD NOT depend on nor enforce the use of back references by
   followup agents. For compatibility with legacy news software the
   Subject-content of a control message (i.e. an article that also
   contains a Control header) MAY start with the string "cmsg ", and
   non-control messages MUST NOT start with the string "cmsg ". See also
   section 6.13.

5.4.1.  Examples

   In the following examples, please note that only "Re: " is mandated
   by this standard. "was: " is a convention used by many English-
   speaking posters to signal a change in subject matter.  Software
   should be able to deduce this information from References.

      Subject: Film at 11
      Subject: Re: Film at 11
      Subject: Godwin's law considered harmful (was: Film at 11)
      Subject: Godwin's law (was: Film at 11)
      Subject: Re: Godwin's law (was: Film at 11)
                          News Article Format                  July 2001

5.5.  Newsgroups

   The Newsgroups header's content specifies the newsgroup(s) in which
   the article is intended to appear. It is an inheritable header
   ( which then becomes the default Newsgroups header of any
   followup, unless a Followup-To header is present to prescribe

   References to "Unicode" or "the latest version of the Unicode
   Standard" mean [UNICODE 3.1] contains guarantees of strict future
   upwards compatibility (e.g. no character will be removed or change
   classification). Implementors should be aware that currently
   unassigned code points (Unicode category Cn) may become valid
   characters in future versions of Unicode. Since the poster of an
   article might have access to a newer version of that standard,
   relaying and serving agents MUST accept such characters, but posting
   agents (and indeed all agents) MUST NOT generate them.

      Newsgroups-content  = newsgroup-name
                               *( *FWS ng-delim *FWS newsgroup-name )
      newsgroup-name      = component *( "." component )
                          News Article Format                 April 2001
      component           = component-start
                               *( component-start / component-other )
      component-start 1*component-glyph
      ng-delim            = Un-lowercase / Un-digit
      Un-lowercase ","
      component-glyph     = combiner-base *combiner-mark
      combiner-base       = <Unicode Letter, Lowercase> /
                            <Unicode Letter, Other>
      Un-digit            = <Unicode Number, Decimal Digit> /
                            <Unicode Number, Other>
      component-other combiner-ASCII / combiner-extended
      combiner-ASCII      = "0"-"9" / %x41-5A / %x61-7A / "+" / "-" / "_"
      combiner-extended   = ","
   where the <Unicode ...> items are as described in [UNICODE].

   The inclusion of folding white space within <any character with a Newsgroups-content is Unicode code value of
                             0080 or greater and a
   newly introduced feature combining class of 0,
                             but excluding any character in this standard. It MUST be accepted by all
   conforming implementations (relaying agents, serving agents Unicode
                             categories Cc, Cf, Cs, Zs, Zl, and
   reading agents).  Posting agents should be aware that such postings
   may be rejected by overly-critical old-style relaying agents. When Zp>
      combiner-mark       = <any character with a
   sufficient number Unicode code value of relaying agents
                             0080 or greater and a combining class other
                             than 0>

        NOTE: the excluded characters are in conformance, posting
   agents SHOULD generate such control characters (Cc),
        format control characters (Cf), surrogates (Cs), and separators
        (Zs, Zl, Zp). In particular, this excludes all whitespace in the form of <CRLF WS> so as
   to keep the length of lines in

   Each component MUST be invariant under Unicode normalization NFKC
   (cf. the relevant weaker normalization requirement for other headers (notably
   Newsgroups and Followup-To) to in
   section 4.4.1 which specified no more than than 79 normalization NFC).

        NOTE: Alternatively, this restriction could have been expressed
        by saying:
          o All characters (or
   other agreed policy limit - see 4.5).  Before such critical mass
   occurs, injecting agents MAY reformat with a compatibility decomposition are
        or else
          o All characters with property NFKC-NO are forbidden.
        The effect is to exclude variant forms of characters, such headers by removing
   whitespace inserted by the posting agent, but relaying agents MUST
   NOT do so.

   A newsgroup-name consists as
        superscripts and subscripts, wide and narrow forms, font
        variants, encircled forms, ligatures, and so on, as their use
        could cause confusion.

                          News Article Format                  July 2001

        As a result of of this restriction, a name has only one valid
        form. Implementations can assume that a straight comparison of
        characters or more components. Components MAY
   contain octets is sufficient to compare two newsgroup-

        NOTE: An implementation is not required to apply NFKC, or any
        other normalization, to newsgroup names. Only agencies that
        create new groups need to be careful to obey this restriction
        (7.1).  However, if a posting agent neglects to normalize a
        newsgroup-name entered manually, this may lead to the user
        posting to a non-existent group without understanding why.

   Newsgroup-names containing non-ASCII letters, but these characters MUST be encoded in
   UTF-8 and not according to [RFC 2047].  A component MUST contain at least one
   letter (and MUST, according to the syntax, begin

   Components beginning with a letter underline ("_") are reserved for use by
   future versions of this standard and MUST NOT occur in newsgroup
   names (whether in Newsgroup headers or
   digit). in newgroup control messages
   (7.1)).  However, such names MUST be accepted.

   Components SHOULD begin beginning with a letter.  Composite characters
   (made "+" or "-" are reserved for use by overlaying one character with another)
   implementations and format
   characters, as allowed MUST NOT occur in certain parts of Unicode and needed by
   certain languages, must use whatever canonical conventions apply to
   those parts of Unicode (such conventions are newsgroup names (whether in
   Newsgroup headers or in newgroup control messages). Implementors may
   assume that this rule will not defined change in any future version of this
   Standard). The

        NOTE: For example, implementors may safely use of "_" in a component is deprecated. Serving
   agents MAY refuse leading "+" and
        "-" to accept newsgroups using such "escape" other entities within something that looks like
        a component.

        NOTE: Components composed entirely of digits would cause
        problems newsgroup-name.

   Agencies responsible for the commonly used implementation technique administration of using particular hierarchies
   Ought to place additional restrictions on the component characters they allow
   in newsgroup-names within those hierarchies (such as the name of a directory, whilst also using
        sequential numbers to distinguish accord with
   the articles languages commonly used within a group.
        Components containing other non-permitted characters could cause
        problems when newsgroup-names appear in URLs [RFC 1738] (for
        example an '@' character would prevent distinguishing between
        newsgroup-names and message identifiers).

        NOTE: According those hierarchies, or to the syntax, uppercase letters cannot occur in
        newsgroup-names, but this standard imposes avoid
   perceived ambiguities pertinent to those languages). Where there is
   no requirement on
        software such specific policy, the following restrictions SHOULD be applied
   to check this condition, since it would newsgroup names.

        NOTE: These restrictions are intended to reflect existing
        practice, with some additions to accomodate foreseeable
        enhancements, and are intended both to avoid certain technical
        difficulties and to avoid unnecessary confusion. It may well be unreasonable
        that experience will allow future extensions to expect it this standard to do so
        relax some or all of these restrictions.

   The specific restrictions (to be applied in parts the absence of Unicode for which it was not
        configured (in general, a table lookup is required). Rather, it
   established policies to the responsibility contrary) are:

   1. The following characters are forbidden, subject to the comments
      and notes at the end of those creating the list:

      characters in category Cn (Other, Not assigned)         [1]
      characters in category Co (Other, Private Use)          [2]
      characters in category Lt (Letter, Titlecase)           [3]
                          News Article Format                  July 2001

      characters in category Lu (Letter, Uppercase)           [3]
      characters in category Me (Mark, Enclosing)             [4]
      characters in category Pd (Punctuation, Dash)           [4][5]
      characters in category Pe (Punctuation, Close)          [4]
      characters in category Pf (Punctuation, Final quote)    [4]
      characters in category Pi (Punctuation, Initial quote)  [4]
      characters in category Po (Punctuation, Other)          [4]
      characters in category Ps (Punctuation, Open)           [4]
      characters in category Sc (Symbol, Currency)            [4]
      characters in category Sk (Symbol, Modifier)            [4]
      characters in category Sm (Symbol, Math)                [4][5]
      characters in category So (Symbol, Other)               [4]

      [1] As new newsgroups (7.1) not characters are added to violate it. It is, moreover, Unicode, the code point moves
          from category Cn to some other category. As stated above,
          implementors should be expected that prepared for this.

      [2] Specific private use characters can be used within a hierarchy
          or co-operating subnet that has agreed meanings for them.

      [3] Traditionally, newsgroup-names have been written in lowercase.
          Posting agents MAY convert these characters to the
          corresponding lowercase forms.
      [That may be better left unsaid, or rewritten]

      [4] Traditionally newsgroup
        created names have only used letters, digits,
          and the three special characters "+", "-" and "_". These
          categories correspond to characters outside that set.

      [5] Although the characters "+" and "-" are within categories Pd
          and Sm, they are not forbidden.

   2. A component name is forbidden to consist entirely of digits.

        NOTE: This requirement was in violation [RFC 1036] but nevertheless
        several such groups have appeared in practice and implementors
        should be prepared for them. A common implementation technique
        uses each component as the name of a directory and uses numeric
        filenames for each article within a group. Such an
        implementation needs to be careful when this could cause a clash
        (e.g. between article 123 of group xxx.yyy and the directory for
        group xxx.yyy.123).
[Open issue a number of people think this condition will should not be propagated
                          News Article Format                 April 2001

        particularly well. a default
requirement but simply be a NOTE; wording for such is further down.]

   3. A component is limited to 30 component-glyphs and a newsgroup-name
      to 71 component-glyphs. Whilst there is no longer any technical
      reason to limit the length of a component (formerly, it was
      limited to 14 characters) octets) nor to limit
   the total length of a newsgroup-name, it should be noted
      that these names are also used in the newsgroups line (7.1.2)
      where an overall policy limit applies, and moreover applies and, moreover, excessively
      long names can be exceedingly inconvenient in practical use.  Agencies responsible for
   individual hierarchies Ought therefore, as a matter of policy, to set
   reasonable limits for the length of a component

                          News Article Format                  July 2001

        NOTE: To all intents and of purposes, a newsgroup-
   name. In the absence of such explicit policies, the default limits
   are 30 characters and 71 characters respectively.
[If the checkpolicies proposal component-glyph is included in the Standard, there should
be what a reference to it here.]

        NOTE: The newsgroup-name
        user might regard as encoded in UTF-8 should be regarded a single "character" as the canonical form. Reading agents may convert displayed on his
        screen, though it might be transmitted as several actual
        characters (e.g. q-circumflex is two characters).

   Serving and relaying agents MUST accept any newsgroup-name that meets
   the above requirements, even if they violate one or more of the
   policy restrictions. Posting and injecting agents MAY reject articles
   containing newsgroup-names that do not meet these restrictions, and
   posting agents MAY attempt to correct them (e.g. by lowercasing).
   However, because of the large and changing tables required to do
   these checks and corrections throughout the whole of Unicode, this
   standard does not require them to do so. Rather, the onus is placed
   on those who create new newsgroups (7.1) to check the mandatory
   requirements, to consider the effects of relaxing the other
   restrictions, and to consider how all this may affect propagation of
   the group.

   Since future extensions to this standard and the Unicode standard,
   plus any relaxations of the default restrictions introduced by
   specific hierarchies, might invalidate some such checks, warnings,
   and adjustments, implementations MUST incorporate means to disable
   them. In particular, implementations must be prepared for a
   relaxation of the normalization requirements (e.g. from NFKC down to
   NFC), which have been made rather stringent due to a lack of
   practical experience in this area.

[Alternative text for Open issue]

        NOTE: Components composed entirely of digits were forbidden by
        [RFC 1036] but have nevertheless been used in practice, and are
        therefore permitted by this specification. A common
        implementation technique uses each component as the name of a
        directory and uses numeric filenames for each article within a
        group. Such an implementation needs to be careful when this
        could cause a clash (e.g. between article 123 of group xxx.yyy
        and the directory for group xxx.yyy.123).
[Open issue: delete the above text if we retain the default requirement

        NOTE: The newsgroup-name as encoded in UTF-8 should be regarded
        as the canonical form. Reading agents may convert it to whatever
        character set they are able to display (see 4.4.1) and serving
        agents may possibly need to convert it to some form more
        suitable as a filename. Simple algorithms for both kinds of
        conversion are readily available.  Observe that the syntax does
        not allow comments within the Newsgroups header; this is to
        simplify processing by relaying and serving agents which have a
        requirement to process this header extremely rapidly.

   The inclusion of folding white space within a Newsgroups-content is a
   newly introduced feature in this standard. It MUST be accepted by all
   conforming implementations (relaying agents, serving agents and
   reading agents).  Posting agents should be aware that such postings
                          News Article Format                  July 2001

   may be rejected by overly-critical old-style relaying agents. When a
   sufficient number of relaying agents are in conformance, posting
   agents SHOULD generate such whitespace in the form of <CRLF WS> so as
   to keep the length of lines in the relevant headers (notably
   Newsgroups and Followup-To) to no more than than 79 characters (or
   other agreed policy limit - see 4.5).  Before such critical mass
   occurs, injecting agents MAY reformat such headers by removing
   whitespace inserted by the posting agent, but relaying agents MUST
   NOT do so.

   Posters SHOULD use only the names of existing newsgroups in the
   Newsgroups header. However, it is legitimate to cross-post to
   newsgroup(s) which do not exist on the posting agent's host, provided
   that at least one of the newsgroups DOES exist there, and followup
   agents SHOULD accept this (posting agents MAY accept it, but Ought at
   least to alert the poster to the situation and request confirmation).
   Relaying agents MUST NOT rewrite Newsgroups headers in any way, even
   if some or all of the newsgroups do not exist on the relaying agent's
   host. Serving agents MUST NOT create new newsgroups simply because an
   unrecognised newsgroup-name occurs in a Newsgroups header (see 7.1
   for the correct method of newsgroup creation).

   The Newsgroups header is intended for use in Netnews articles rather
   than in mail messages. It MAY be used in a mail message to indicate
   that it is a copy also posted to the listed newsgroups, but it SHOULD
   NOT be used in a mail-only reply to a Netnews article (thus the
   "inheritable" property of this header applies only to followups to a
   newsgroup, and not to followups to the poster). Moreover, if a
   newsgroup-name contains any non-ASCII character, it MAY be encoded
   using the mechanism defined in [RFC 2047] when sent by mail but, if
   it is subsequently returned to the Netnews environment, it MUST then
   be re-encoded into UTF-8.

5.5.1.  Forbidden newsgroup names

   The following forms of newsgroup-name MUST NOT be used except for the
   specific purposes indicated:

                          News Article Format                 April 2001

     o Newsgroup-names having only one component. These are reserved for
       newsgroups whose propagation is restricted to a single host or
       local network, and for pseudo-newsgroups such as "poster" (which
       has special meaning in the Followup-To header - see section 6.7),
       "junk" (often used by serving agents), "control" (likewise),
       "revise" and "repost" (which have special meanings in the Xref
       header - see 6.16)

     o Any newsgroup-name beginning with "control." (used as pseudo-
       newsgroups by many serving agents)
     o Any newsgroup-name containing the component "ctl" (likewise)
     o "to" or any newsgroup-name beginning with "to." (reserved for the
       ihave/sendme protocol described in section 7.6, and for test
       messages sent on an essentially point-to-point basis)
                          News Article Format                  July 2001

     o Any newsgroup-name beginning with "example." (reserved for
       examples in this and other standards)
     o Any newsgroup-name containing the component "all" (because this
       is used as a wildcard in some implementations)

   A newsgroup-name SHOULD NOT appear more than once in the Newsgroups
   header.  The order of newsgroup names in the Newsgroups header is not
   significant, except for determining which moderator to send the
   article to if more than one of the groups is moderated (see 8.2).

5.6.  Path

   The Path header shows the route taken by a message since its entry
   into the Netnews system. It is a variant header (, (, each agent
   that processes an article being required to add one (or more) entries
   to it. This is primarily to enable relaying agents to avoid sending
   articles to sites already known to have them, in particular the site
   they came from, and additionally to permit tracing the route articles
   take in moving over the network, and for gathering Usenet statistics.
   Finally the presence of a '%' delimiter in the Path header can be
   used to identify an article injected in conformance with this

5.6.1.  Format

      Path-content        = *( path-identity [FWS] delimiter [FWS] )
                               tail-entry *FWS
      path-identity       = 1*( ALPHA / DIGIT / "-" / "." / ":" / "_" )
      delimiter           = "/" / "?" / "%" / "," / "!"
      tail-entry          = 1*( ALPHA / DIGIT / "-" / "." / ":" / "_" )

        NOTE: A Path-content will inevitably contain at least one path-
        identity, except possibly in the case of a proto-article that
        has not yet been injected onto the network.

        NOTE: Observe that the syntax does not allow comments within the
        Path header; this is to simplify processing by relaying and
        injecting agents which have a requirement to process this header
        extremely rapidly.

                          News Article Format                 April 2001

   A relaying agent SHOULD NOT pass an article to another relaying agent
   whose path-identity (or some known alias thereof) already appears in
   the Path-content. Since the comparison may be either case sensitive
   or case insensitive, relaying agents SHOULD NOT generate a name which
   differs from that of another site only in terms of case.

   A relaying agent MAY decline to accept an article if its own path-
   identity is already present in the Path-content or if the Path-
   content contains some path-identity whose articles the relaying agent
   does not want, as a matter of local policy.

        NOTE: This last facility is sometimes used to detect and decline
        control messages (notably cancel messages) which have been
        deliberately seeded with a path-identity to be "aliased out" by
                          News Article Format                  July 2001

        sites not wishing to act upon them.

5.6.2.  Adding a path-identity to the Path header

   When an injecting, relaying or serving agent receives an article, it
   MUST prepend its own path-identity followed by a delimiter to the
   beginning of the Path-content. In addition, it SHOULD then add CRLF
   and WSP if it would otherwise result in a line longer than 79

   The path-identity added MUST be unique to that agent. To this end it
   SHOULD be one of:

   1. A fully qualified domain name (FQDN) associated (by the Internet
      DNS service [RFC 1034]) with an A record, which SHOULD identify
      the actual machine prepending this path-identity. Ideally, this
      FQDN should also be "mailable" in the sense that it enables the
      construction of a valid E-mail address of the form "usenet@<FQDN>"
      or "news@<FQDN>" [RFC 2142] whereby the administrators of that
      agent may be reached.

   2. A fully qualified domain name (FQDN) associated (by the Internet
      DNS service) with an MX record which MUST then enable the
      construction of a valid E-mail address of the form "usenet@<FQDN>"
      or "news@<FQDN>" whereby the administrators of that agent may be

   3. A An arbitrary name believed to be unique and registered previously in the UUCP maps database (found in at least
      with all sites immediately downstream from the newsgroup comp.mail.maps), containing no '.' character. given site.

   4. An encoding of an IP address - <dotted-quad> [RFC 820] or <ipv6-
      numeric> [RFC 2373] (the requirement to be able to use an <ipv6-
      numeric> is the reason for including ':' as an allowed character
      within a path-identity).

   5. A '.' followed by an arbitrary name not in the UUCP maps database,
      but believed to be unique and registered at least with all sites
      immediately downstream from the given site.

                          News Article Format                 April 2001

   Of the above options, nos. 1 to 3 are much to be preferred, unless
   there are strong technical reasons dictating otherwise. In
   particular, the injecting agent's path-identity MUST, as a special
   case, be an FQDN mailable address in the sense defined under option
   1, or with an associated MX record as in option 2.

   The injecting agent's path-identity MUST be followed by the special
   delimiter '%' which serves to separate the pre-injection and post-
   injection regions of the Path-content (see 5.6.3).

   In the case of a relaying or serving agent, the delimiter is chosen
   as follows.  When such an agent receives an article, it MUST
   establish the identity of the source and compare it with the leftmost
   path-identity of the Path-content. If it matches, a '/' should be
   used as the delimiter when prepending the agent's own path-identity.
   If it does not match then the agent should prepend two entries to the
   Path-content; firstly the true established path-identity of the
   source followed by a '?'  delimiter, and then, to the left of that,
   the agent's own path-identity followed by a '/' delimiter as usual.

                          News Article Format                  July 2001

   This prepending of two entries SHOULD NOT be done if the provided and
   established identities match.

   Any method of establishing the identity of the source may be used
   (but see 5.6.5 below), with the consideration that, in the event of
   problems, the agent concerned may be called upon to justify it.

        NOTE: The use of the '%' delimiter marks the position of the
        injecting agent in the chain. In normal circumstances there
        should therefore be only one `%` delimiter present, and
        injecting agents MAY choose to reject proto-articles with a '%'
        already in them. If, for whatever reason, more than one '%' is
        found, then the path-identity in front of the leftmost '%' is to
        be regarded as the true injecting agent.

5.6.3.  The tail-entry

   For historical reasons, the tail-entry (i.e. the rightmost entry in
   the Path-content) is regarded as a "user name", and therefore MUST
   NOT be interpreted as a site through which the article has already
   passed. Moreover, the Path-content is not an E-mail address and MUST
   NOT be used to contact the poster. Posting and/or injecting agents
   MAY place any string here. When it is not an actual user name, the
   string "not-for-mail" is often used, but in fact a simple "x" would
   be sufficient.

   Often this field will be the only entry in the region (known as the
   pre-injection region) after the '%', although there may be entries
   corresponding to machines traversed between the posting agent and the
   injecting agent proper. In particular, injecting agents that receive
   articles from many sources MAY include information to establish the
   circumstances of the injection such as the identity of the source
   machine (especially if the Injector-Info header (6.19) is absent).
   Any such inclusion SHOULD NOT conflict with any genuine site
   identifier. The '!'  delimiter may be used freely within the pre-
                          News Article Format                 April 2001
   injection region, although '/' and '?' are also appropriate if used

5.6.4.  Delimiter Summary

   A summary of the various delimiters. The name immediately to the left
   of the delimiter is always that of the machine which added the

   '/' The name immediately to the right is known to be the identity of
       the machine from which the article was received (either because
       the entry was made by that machine and we have verified it, or
       because we have added it ourselves).

   '?' The name immediately to the right is the claimed identity of the
       machine from which the article was received, but we were unable
       to verify it (and have prepended our own view of where it came
       from, and then a '/').

                          News Article Format                  July 2001

   '%' Everything to the right is the pre-injection region followed by
       the tail-entry.  The name on the left is the FQDN of the
       injecting agent. The presence of two '%'s in a path indicates a
       double-injection (see 8.2.2).

   '!' The name immediately to the right is unverified. The presence of
       a '!' to the left of the '%' indicates that the identity to the
       left is that of an old-style system not conformant with this

   ',' Reserved for future use, treat as '/'.

       Old software may possibly use other delimiters, which should be
       treated as '!'.  But note in particular that ':', '-' and '_' are
       components of names, not delimiters, and FWS on its own MUST NOT
       be used as the sole delimiter.

        NOTE: Old Netnews relaying and injecting programs almost all
        delimit Path entries with the '!' delimiter, and these entries
        are not verified. As such, the presence of '%' as a delimiter
        will indicate that the article was injected by software
        conforming to this standard, and the presence of '!' as a
        delimiter to the left of a '%' will indicate that the message
        passed through systems developed prior to this standard. It is
        anticipated that relaying agents will reject articles in the old
        style once this new standard has been widely adopted.

5.6.5.  Suggested Verification Methods

   The following approaches for common transports are suggested in order
   to meet a site's verification obligations. They are not required, but
   following them should avoid the necessity for wasteful double-entry
   Path additions.

                          News Article Format                 April 2001

   If the incoming article arrives through some TCP/IP protocol such as
   NNTP, the IP address of the source will be known, and will likely
   already have been checked against a list of known FQDNs or IP
   addresses that the receiving site has agreed to peer with (this will
   have involved a DNS lookup of a known FQDN, following CNAME chains as
   required, to find an A record containing that source IP).

   1. Where the path-identity is an FQDN (or even an arbitrary name
      starting with a '.') it is now a simple matter to check that it is
      the proper FQDN for the source, or some known registered alias
      thereof. Alternatively, where the FQDN in the path-identity has an
      associated A record, an immediate DNS lookup as above can be used
      to verify it.

   2. Where the path-identity is an encoding of an IP address which does
      not immediately match the known IP address of the source, a
      reverse-DNS ( PTR record) lookup may be done on the
      provided address, followed by a regular DNS "A" record lookup on
      the returned name. There may be A records for several IP
                          News Article Format                  July 2001

      addresses, of which one should match the path-identity and another
      should match the source.

   3. If the path-identity fails to match any known alias for the source
      (requiring the insertion of an extra path-identity for the true
      source followed by a '?'), simply doing a reverse DNS (PTR) lookup
      on the source IP address is not sufficient to generate the true
      FQDN. The returned name must be mapped back to A records to assure
      it matches the source's IP address.

   If the incoming article arrives through some other protocol, such as
   UUCP, that protocol MUST include a means of verifying the source
   site. In UUCP implementations, commonly each incoming connection has
   a unique login name and password, and that login name (or some alias
   registered for it) would be expected as the path-identity.
[The above description may still contain more detail that we would wish.
My aim so far was to retain everything in Brad's original, but expressed
in a more palatable manner. We can now decide how much of it we want to

5.6.6.  Example

      Path: foo.isp.example/

        NOTE: That article was injected into the news stream by
        baz.isp.example (complaints may be addressed to
        usenet@baz.isp.example). The injector has taken care to record
        that it got it from dialup123.baz.isp.example. "x" is the
        default tail entry, though sometimes a real userid is put there.

                          News Article Format                 April 2001

        The article was relayed, perhaps by UUCP, to the machine known
        in the UUCP maps database known,
        at least to its downstream, as "barbaz".

        Barbaz relayed it to, which does not yet
        conform to this standard (hence the '!' delimiter). So one
        cannot be sure that it really came from barbaz. relayed it to a site claiming to have the IP
        address [], and claiming (by using the '/' delimiter)
        to have verified that it came from

        [] relayed it to ".foo-server" "foo-server" which, not being
        convinced that it truly came from [], did a reverse
        lookup on the actual source and concluded it was known as
        bar.isp.example (that is not to say that [] was not a
        correct IP address for bar.isp.example, but simply that that
        connection could not be substantiated by .foo-server). foo-server).  Observe
        that .foo-server foo-server has now added two entries to the Path.


                          News Article Format                  July 2001

        "foo-server" is a locally significant name (observe the
        presence of the '.') within the complex
        site of many machines run by foo.isp.example, so the latter
        should have no problem recognizing .foo-server foo-server and using a '/'
        delimiter.  Presumably foo.isp.example then delivered the
        article to its direct clients.

        It appears that foo.isp.example and decided to
        fold the line, on the grounds that it seemed to be getting a
        little too long.

6.  Optional Headers

   The headers appearing in this section have established meanings and
   MUST be interpreted according to the definitions given here. None of
   them is required to appear in every article but some of them are
   required in certain types of article, such as followups. Any header
   defined in this (or any other) standard MUST NOT appear more than
   once in an article unless specifically stated otherwise.
   Experimental headers ( and headers defined by cooperating
   subnets are exempt from this requirement.  See section 8 "Duties of
   Various Agents" for the full picture.

6.1.  Reply-To

   The Reply-To header specifies a reply address(es) to be used for
   personal replies for the author(s) poster(s) of the article when this is
   different from the author's poster's address(es) given in the From header. The
   content syntax makes use of syntax defined in [MESSFOR], [RFC 2822], but subject
   to the revised definition of local-part given in section 5.2.

      Reply-To-content    = From-content  ; see 5.2
                          News Article Format                 April 2001

   In the absence of Reply-To, the reply address(es) is the address(es)
   in the From header. For this reason a Reply-To SHOULD NOT be included
   if it just duplicates the From header.

        NOTE: Use of a Reply-To header is preferable to including a
        similar request in the article body, because reply agents can
        take account of Reply-To automatically.

   An address of "<>" in the Reply-To header MAY be used to indicate
   that the poster does not wish to recieve email replies.

6.1.1.  Examples

      Reply-To: John Smith <jsmith@site.example>
      Reply-To: John Smith <jsmith@site.example>, dave@isp.example
      Reply-To: John Smith <jsmith@site.example>,andrew@isp.example,
      Reply-To: Please do not reply <>
                          News Article Format                  July 2001

6.2.  Sender

   The Sender header specifies the mailbox of the entity which actually
   sent this article, if that entity is different from that given in the
   From header or if more than one address appears in the From header.
   This header SHOULD NOT appear in an article unless the sender is
   different from the author. poster. This header is appropriate for use by
   automatic article posters. The content syntax makes use of syntax
   defined in [MESSFOR]. [RFC 2822].

      Sender-content      = mailbox

6.3.  Organization

   The Organization header is a short phrase identifying the author's poster's

      Organization-content= 1*( [FWS] utext )

        NOTE: Posting and injecting agents are discouraged from
        providing a default value for this header unless it is
        acceptable to all posters using those agents. Unless this header
        contains useful information (including some indication of the
        posters physical location) posters are discouraged from
        including it.

6.4.  Keywords

   The Keywords field contains a comma separated list of important words
   and phrases intended to describe some aspect of the content of the
   article. The content syntax makes use of syntax defined in [MESSFOR]. [RFC

      Keywords-content    = phrase *( "," phrase )
                          News Article Format                 April 2001

        NOTE: The list is comma separated NOT space separated.

6.5.  Summary

   The Summary header is a short phrase summarizing the article's

      Summary-content     = 1*( [FWS] utext )

   The summary should be terse. Authors Ought to avoid trying to cram
   their entire article into the headers; even the simplest query
   usually benefits from a sentence or two of elaboration and context,
   and not all reading agents display all headers. On the other hand the
   summary should give more detail than the Subject.

                          News Article Format                  July 2001

6.6.  Distribution

   The Distribution header is an inheritable header (see which
   specifies geographical or organizational limits to an article's

      Distribution-content= distribution *( dist-delim distribution )
      dist-delim          = ","
      distribution        = positive-distribution /
                          = *FWS distribution-name *FWS
                          = *FWS "!" distribution-name *FWS
      distribution-name   = letter ALPHA 1*distribution-rest
      distribution-rest   = letter ALPHA / "+" / "-" / "_"

        NOTE: The use of ALPHA in the syntax ensures that distribution
        names are always in US-ASCII.

   Articles MUST NOT be passed between relaying agents or to serving
   agents unless the sending agent has been configured to supply and the
   receiving agent to receive BOTH of
       (a) at least one of the newsgroups in the article's Newsgroups
       header, and
       (b) at least one of the positive-distributions (if any) in the
       article's Distribution header and none of the negative-
   Additionally, reading agents MAY be configured so that unwanted
   distributions do not get displayed.

        NOTE: Although it would seem redundant to filter out unwanted
        distributions at both ends of a relaying link (and it is clearly
        more efficient to do so at the sending end), many sending sites
        have been reluctant, historically speaking, to apply such
        filters (except to ensure that distributions local to their own
        site or cooperating subnet did not escape); moreover they tended
        to configure their filters on an "all but those listed" basis,
        so that new and hitherto unheard of distributions would not be
        caught. Indeed many "hub" sites actually wanted to receive all
        possible distributions so that they could feed on to their
        clients in all possible geographical (or organizational)
                          News Article Format                 April 2001

        Therefore, it is desirable to provide facilities for rejecting
        unwanted distributions at the receiving end. Indeed, it may be
        simpler to do so locally than to inform each sending site of
        what is required, especially in the case of specialized
        distributions (for example for control messages, such as cancels
        from certain issuers) which might need to be added at short
        notice.  Tha possibility for reading agents to filter
        distributions has been provided for the same reason.

                          News Article Format                  July 2001

   Exceptionally, ALL relaying agents are deemed willing to supply or
   accept the distribution "world", and NO relaying agent should supply
   or accept the distribution "local".  However, "world" SHOULD NEVER be
   mentioned explicitly since it is the default when the Distribution
   header is absent entirely.  "All" MUST NOT be used as a
   distribution-name.  Distribution-names SHOULD contain at least three
   characters, except when they are two-letter country names as in [ISO
   3166].  Distribution-names are case-insensitive (i.e. "US", "Us" and
   "us" all specify the same distribution).

        NOTE: "Distribution: !us" can be used to cause an article to go
        to the whole of "world" except for "us".

   Posting agents Ought Not to provide a default Distribution header
   without giving the poster an opportunity to override it. Followup
   agents SHOULD initially supply the same Distribution header as found
   in the precursor.

6.7.  Followup-To

   The Followup-To header specifies which newsgroup(s) followups should
   be posted to.

      Followup-To-content = Newsgroups-content / "poster"

   The syntax is the same as that of the Newsgroups-content, with the
   exception that the magic word "poster" is allowed. In the absence of
   a Followup-To header, the default newsgroup(s) for a followup are
   those in the Newsgroups header, and for this reason the Followup-To
   header SHOULD NOT be included if it just duplicates the Newsgroups

   A Followup-To header consisting of the magic word "poster" indicates
   that the author poster requests no followups to be sent in response to this
   article, only personal replies to the article's reply address.

        NOTE: An author A poster who wishes both  a personal reply and a followup
        post should include a Mail-Copies-To header (6.8).

                          News Article Format                 April 2001

6.8.  Mail-Copies-To

   The Mail-Copies-To header indicates whether or not the poster wishes
   to have followups to an article emailed in addition to being posted
   to Netnews and, if so, establishes the address to which they should
   be sent.

   The content syntax makes use of syntax defined in [MESSFOR], [RFC 2822], but
   subject to the revised definition of local-part given in section 5.2.

      Mail-Copies-To-content    = copy-addr / "nobody" / "poster"
      copy-addr                 = mailbox
                          News Article Format                  July 2001

   The keyword "nobody" indicates that the author poster does not wish copies
   of any followup postings to be emailed. This indication is widely
   seen as a very strong wish, and is to be taken as the default when
   this header is absent.

   The keyword "poster" indicates that the author poster wishes a copy of any
   followup postings to be emailed to him.

   Otherwise, this header contains a copy-addr to which the author poster
   wishes a copy of any followup postings to be sent.

        NOTE: Some existing practice uses the keyword "never" in place
        of "nobody" and "always" in place of "poster". These usages are
        deprecated, but followup agents MAY observe them.

   The automatic actions of a followup agent in the various cases
   (subject to manual override by the user) are as follows:

   nobody (or when the header is absent)
      The followup agent SHOULD NOT, by default, email such a copy and
      Ought, especially when there is an explicit "nobody", to issue a
      warning and ask for confirmation if the user attempts to do so.

      The followup agent Ought, by default, to email a copy, which MUST
      then be sent to the address in the Reply-To header, and in the
      absence of that to the address(es) in the From header.

      The followup agent Ought, by default, to email a copy, which MUST
      then be sent to the copy-addr.

        NOTE: This header is only relevant when posting followups to
        Netnews articles, and is to be ignored when sending pure email
        replies to the author, poster, which are handled as prescribed under the
        Reply-To header (6.1).  Whether or not this header will also
        find similar usage for replies to messages sent to mailing lists
        falls outside the scope of this standard.

                          News Article Format                 April 2001

   When emailing a copy, the followup agent SHOULD also include a
   "Posted-And-Mailed: yes" header (6.9).

        NOTE: In addition to the Posted-And-Mailed header, some followup
        agents also include within the body a mention that the article
        is both posted and mailed, for the benefit of reading agents
        that do not normally show that header.

6.9.  Posted-And-Mailed

      Posted-And-Mailed-content = "yes" / "no"

   This header, when used with the "yes" keyword, indicates that the
   article has been both posted to the specified newgroups newsgroups and emailed.
   It SHOULD be used when replying to the author poster of an article to which
                          News Article Format                  July 2001

   this one is a followup (see the Mail-Copies-To header in section 6.8)
   and it MAY be used when any article is also mailed to a recipient(s)
   identified in a To and/or Cc header that is also present. The "no"
   keyword is included for the sake of completeness; it MAY be used to
   indicate the opposite state, but is redundant insofar as it only
   describes the default state when this header is absent.

   This header, if present, MUST be included in both the posted and
   emailed versions of the article. The Newsgroups header of the posted
   article SHOULD be included in the email version as recommended in
   section 5.5.  All other headers defined in this standard (excluding
   variant and local headers, but including specifically the Message-ID header)
   MUST be identical in both the posted and mailed versions of the
   article, and so MUST the body.

        NOTE: This leaves open the question of whether a To or a Cc
        header should appear in the posted version. Naturally, a Bcc
        header should not appear, except in a form which indicates that
        there are additional unspecified recipients.

6.10.  References

   The References header lists optionally CFWS-separated message
   identifiers of precursors. The content syntax makes use of syntax
   defined in [MESSFOR]. [RFC 2822].

      References-content  = msg-id *( CFWS msg-id )

        NOTE: This differs from the syntax of [MESSFOR] [RFC 2822] by requiring at
        least one CFWS between the msg-ids (this was an [RFC 1036]

   A followup MUST have a References header, and an article that is not
   a followup MUST NOT have a References header. In a followup, if the
   precursor did not have a References header, the followup's
   References-content MUST be formed by the message identifier of the
   precursor. A followup to an article which had a References header
   MUST have a References header containing the precursor's References-
   content (subject to trimming as described below) plus the precursor's
                          News Article Format                 April 2001
   message identifier appended to the end of the list (separated from it
   by CFWS).

   Followup agents SHOULD NOT trim message identifiers out of a
   References header unless the number of message identifiers exceeds
   21, at which time trimming SHOULD be done by removing sufficient
   identifiers starting with the second so as to bring the total down to
   21. However, it would be wrong to assume that References headers
   containing more than 21 message identifiers will not occur.

6.10.1.  Examples

      References: <i4g587y@site1.example>
      References: <i4g587y@site1.example> <kgb2231+ee@site2.example>
                          News Article Format                  July 2001

      References: <i4g587y@site1.example> <kgb2231+ee@site2.example>
         <222@site1.example> <87tfbyv@site7.example>
      References: <i4g587y@site1.example> <kgb2231+ee@site2.example>

6.11.  Expires

   The  Expires  header specifies a date and time when the article is
   deemed to be no longer relevant and  could usefully  be removed
   ("expired"). The content syntax makes use of syntax defined in

      Expires-content     = date-time

   An Expires header should only be used in an article if the requested
   expiry time is earlier or later than the time typically to be
   expected for such articles. Local policy for each serving agent will
   dictate whether and when this header is obeyed and authors posters SHOULD NOT
   depend on it being completely followed.

6.12.  Archive

   This optional header is a signal to automatic archival agents on
   whether this provides an indication of the poster's intent
   regarding preservation of the article is available for long-term in publicly accessible long-
   term or permanent storage.

      Archive-content     = [CFWS] ("no" | "yes" ) [CFWS]
                          = Filename-token "=" value
                            ; for USENET-header-parameters see 4.1
      Filename-token      = [CFWS] "filename" [CFWS]

   Agents which see

   The presence of an "Archive: no" MUST NOT keep the header in an article past indicates that
   date when it would otherwise have expired. poster does not permit redistribution from publicly accessible
   long-term or permanent archives. The absence of this header, or an
   explicit "Archive: yes" merely
   confirms what is already yes", indicates that the default state. poster is willing for
   such redistribution to take place. The optional Filename parameter MAY
   can then be used to suggest a filename under which the article should
   be archived. stored. Further extensions to this standard may provide additional
   parameters for administration of the archiving process.

        NOTE: This standard does not attempt to define the length of
        "long-term", since it is dependent on many factors, including
        the retention policies of individual sites, and the customs or
        policies established for particular newsgroup or hierarchies.

        NOTE: Posters are cautioned that some sites may not implement
        the "no" option of the Archive header correctly. In some
        jurisdictions non-compliance with this header may constitute a
        breach of copyright or of other legal provisions.  Moreover,
        even if this header prevents the poster's words from being
        archived publicly, it does nothing to prevent the archiving of a
        followup in which those words are quoted.

                          News Article Format                 April                  July 2001

6.13.  Control

   The Control header marks the article as a control message, and
   specifies the desired actions (other than the usual ones of storing
   and/or relaying the article).

      Control-content     = CONTROL-verb CONTROL-argument
      CONTROL-verb        = <the verb defined in this standard
                               (or an extension of it) for a specific
                               CONTROL message>
      verb                = token
      CONTROL-arguments   = <the argument defined in this standard
                               (or an extension of it) for a specific
                               CONTROL message>
      arguments           = *( CFWS value )  ; see 4.1
[Observe that <value> reqires the use of a quoted-string if any
tspecials or NON-ASCII non-ASCII characters are involved. This is a restriction on
present usage, but follows Mime MIME practice.]

   The verb indicates what action should be taken, and the argument(s)
   (if any) supply details. In some cases, the body of the article may
   also contain details. Section 7 describes all of the standard verbs.

   An article with a Control header MUST NOT also have a Replaces or
   Supersedes header.

        NOTE: The presence of a Subject header starting with the string
        "cmsg " and followed by a Control-content MUST NOT be construed,
        in the absence of a proper Control header, as a request to
        perform that control action (as may have occurred in some legacy
        software). See also section 5.4.

6.14.  Approved

   The Approved header indicates the mailing addresses (and possibly the
   full names) of the persons or entities approving the article for

      Approved-content    = From-content  ; see 5.2

   Each mailbox contained in the Approved-content MUST be that of the
   person or entity in question, and one of those mailboxes MUST be that
   of the actual injector of the article.
[This is the start of an attempt to strengthen this header. It should be
a TOSSable offence to put a dummy or invalid address in here. Later,
when we have some form of authentication, I would hope to be able to say

   An Approved header is required in all postings to moderated
   newsgroups. If this header is not present in such postings, then
   relaying and serving agents MUST reject the article. Please see
   section 8.2.2 for how injecting agents should treat postings to
   moderated groups that do not contain this header.

                          News Article Format                 April                  July 2001

   An Approved header is also required in certain control messages, to
   reduce the risk of accidental posting of same; see the relevant parts
   of section 7.

6.15.  Replaces / Supersedes

   These two headers contain one or more message identifiers that the
   current article is expected to replace or supersede. All listed
   articles MUST be treated as though a "cancel" control message had
   arrived for the article (but observe that a site MAY choose not to
   honour a "cancel" message, especially if its authenticity is in

6.15.1.  Syntax and Semantics

   The  Replaces and Supersedes headers specify articles to be cancelled
   on arrival of this one. The content syntax makes use of syntax
   defined in [MESSFOR]. [RFC 2822].

      Replaces-content    = msg-id *( CFWS msg-id )
                          = Disposition-token "=" [CFWS]
                               ( Disposition-value /
                                 DQUOTE Disposition-value DQUOTE )
                            ; for USENET-header-parameters see 4.1
      Disposition-token   = [CFWS] "disposition" [CFWS]
      Disposition-value   = "replace" / "revise" / "repost"
      Supersedes-content  = msg-id

        NOTE: There is no "c" in "Supersedes".

   If an article contains a Replaces header, then the old articles
   mentioned SHOULD simply be deleted by the serving agent, as in a
   cancel message (7.5), and the new article inserted into the system as
   any other new article would be.

   A Replaces-header-parameter is only meaningful when it occurs within
   a Replaces-content. If its Disposition-value is "revise" or "repost"
   (or if the Replaces-header-parameter is absent, then by default)
   reading agents Ought Not to show the article as an "unread" article
   unless the replaced article(s) were themselves all unread, except
   when the reader has configured his reading agent otherwise.

   Moreover, if a Disposition-value is "revise" or "repost", serving
   agents that generate a local Xref header MUST then include additional
   "revise" or "repost" information as set out in section 6.16.

        NOTE: A replacement with "disposition=replace" is intended to be
        used in the case of an article that is sufficiently different
        from its predecessors that it is advisable for readers to see it
        again.  A replacement with "disposition=revise" is intended to
        be used in the case of a minor change, unworthy of being brought
                          News Article Format                 April                  July 2001

        to the attention of a reader who has already read one of its
        predecessors. A replacement with "disposition=repost" is
        intended to be used in the case of an article identical to the
        one replaced (but possibly being reposted because the earlier
        one had likely expired).

        NOTE: A reader who elects to ignore all the articles available
        in a newsgroup (perhaps on the occasion of accessing that
        newsgroup for the first time) will likely have them all marked
        as "already read", unless the reading agent provides a distinct
        mark such as "never offered". This could lead to a later
        replacement with "revise" or "repost" for one of those articles
        being missed.

   The Supersedes header is obsolescent, is provided only for
   compatibility with existing software, and may be removed entirely in
   some future version of this standard. Its meaning is the same as that
   of a corresponding Replaces header with its Replaces-header-parameter
   set to "disposition=replace", and whenever a Supersedes header is
   provided a matching Replaces header SHOULD be provided as well.
   Observe that the Supersedes header makes provision for only a single

   Until the Replaces header has become widely implemented, software
   SHOULD generate Replaces headers with only one msg-id, and cancel
   control messages SHOULD be issued if needed for further identifiers.
   Moreover, until that time, any article containing a Replaces header
   SHOULD contain also a Supersedes header (or alternatively be
   accompanied by a Control cancel message) for that same msg-id, to
   ensure that older systems still at least remove the predecessor.

   When a message contains both a Replaces and a Supersedes header they
   MUST be for the same msg-id.  Furthermore, to resolve any doubt, the
   Replaces header shall be deemed to take priority.

   Whatever security or authentication mechanisms are required for a
   Control cancel message MUST also be required for an article with a
   Replaces or Supersedes header. In the absence or failure of such
   checks, the article SHOULD be discarded, or at most stored as an
   ordinary article.
[We can write something more constructive in here as soon as the
situation with regard to cancel-locks and signed headers has been

6.15.2.  Message-ID version procedure

   Whilst this procedure is not essential for the operation of Netnews,
   it SHOULD be supported by all serving agents. However, for the
   procedure to work, all the msg-ids in the Replaces-content MUST be
   those of successive replacements of the same original article, and
   all be generated as described below.
[Whilst the procedure about to be described will undoubtedly work, it
must be pointed out that life would be much simpler if there was only a
single msg-id allowed in a Replaces-content.]
                          News Article Format                 April                  July 2001  Message version numbers

   According to [MESSFOR], and omitting the obsolete forms, the syntax
   of the left hand side of a msg-id (the part before the "@") is given

      id-left-side        = dot-atom-text / no-fold-quote

   Consider this to be replaced by:

      id-left-side        = ( atom-text / no-fold-quote )
                               *( dollars-sequence )
      dollars-sequence    = version-number / random-dollars-sequence
      version-number      = "$" %d118 "=" 1*DIGIT ; $v=digits
                          = "$" 1*atom-text

   Whilst this is admittedly ambiguous ("$" is already a possible value
   of atom-text) and does not in fact change what is allowable as an
   id-left-side, it does serve to allow dollars-sequences such as
   version-number (and any others that may be added by extensions to
   this standard) to be distinguished within a message identifier and
   utilized by agents which can understand them.  Observe that no-fold-
   quotes cannot occur within a dollars-sequence.

   Posters and/or posting agents when replacing (or superseding)
   articles SHOULD arrange that the message identifier of the
   replacement follows the following convention, generating what are
   known as "version-number" message identifiers. This is to enable the
   new version of the article to be retrieved by its original message
   identifier, notably when it occurs in a URL of the form
   <news:message-identifier> [RFC 1738].

   1. If the id-left-side of the most recent predecessor's message
      identifier contains a leftmost version-number "$v=<n>", where <n>
      is an integer version number, possibly followed by one or more
      random-dollars-sequences, the replacement message identifier
      should be obtained by replacing the <n> with the integer <n+1> and
      providing a different random-dollars-sequence(s). For example
      <foo$v=3$XYZ@faq-site.example> becomes <foo$v=4$PQR@faq-

   2. If the id-left-side of the predecessor's message identifier does
      not contain a version-number, the replacement message identifier
      should be obtained by appending the string "$v=1", preferably
      followed by a random-dollars-sequence(s), to that id-left-side.
      For example <foo@faq-site.example> becomes <foo$v=1$ABC@faq-

   Any random-dollars-sequence so added MUST NOT start with "$<l>=" for
   any letter <l>.

                          News Article Format                 April                  July 2001

        NOTE: The presence of a random-dollars-sequence following the
        version-number is intended to prevent a malicious poster from
        preempting the posting of a replacement article by guessing its
        likely message identifier.

   Attempts to fetch a replaced (or superseded) article by its message
   identifier SHOULD retrieve instead its most recent successor which
   has used the version-number convention. This is intended to ensure
   that "news:" URLs [RFC-1738] [RFC 1738] will continue to work even when an
   article has been replaced, but agents Ought then to draw the user's
   attention to the fact that the message identifier retrieved differed
   from that requested.  Implementation and Use Note

[Here is the implementation technique that we discussed, based on the
use of a conventional History file. This is a sanity check for our own
use, not intended to go in the final text. There are two cases to
A. Traditional implementations (e.g. CNEWS) where each History file line
includes a full message-identifier plus an item for each group in which
the article appears. Thus History file entries are of variable length,
and it is impractical to update them in situ.
B. History files made up of fixed length records (e.g. as proposed for
INN), which enables entries to be overwritten in situ. The History line
typically contains a hash of the message identifier plus some pointer to
an object representing the article as stored.

We consider the traditional case first:

1A. Ensure that the implementation of DBZ is not upset if the same key
is attempted to be stored a second time, and that such a key always
retrieves the latest record indexed by that key.

2A. Additions to the History file are always made at the end. Removals
or changes to existing entries are only made by the expire program. An
entry for a Replaced (or otherwise cancelled) article will remain until,
first, the expire program removes the links to the articles that are no
longer stored, and later on removes the entire entry according to its
expiry date. For every entry containing a '$v=n' followed by random-
dollars-sequences there will be an immediately following entry identical
but for the omission of that '$v=n' and of the random-dollars-sequences.
Thus there may be several entries with identical message-ids but,
because of the change to DBZ just described, only the most recent will
ever be seen except by programs that access the History file directly,
rather than by its index.
3A. When an article is Replaced, at the same time as the successor
article is entered into the History file, with '$v=7' say, a duplicate
entry (same article list) is entered under the same key, modified by
removing any leftmost '$v=n' and the following random-dollars-sequences
from it.

For the fixed length implementations, these steps become:

                          News Article Format                 April                  July 2001

1B. DBZ does not need to be changed.
2B. History file entries may be updated in situ. An entry for a Replaced
(or otherwise cancelled) article can be overwritten with that for the
new article (or with a suitable indication of cancellation). For every
entry containing a '$v=n' followed by random-dollars-sequences there
will always exist a second entry identical but for the omission of that
'$v=n' and of the random-dollars-sequences, both entries pointing to the
same article object.
3B. When an article is Replaced, at the same time as the successor
article is entered into the History file, with '$v=7' say, the existing
entry without the leftmost '$v=n' and the following random-dollars-
sequences is overwritten (with the new article and new expiry date,
after destroying the old article, of course).  If no such entry exists,
one is created.

>From here on, the two cases are the same:

4. Provide a call to a routine which, if asked to retrieve any message
identifier with '$v=n' and finding it missing (or rather linked to no
stored groups), immediately tries again without the '$v=n' and its
random-dollars-sequences.  NOTE. We don't want this behaviour when
checking whether we already have an article offered to us by IHAVE, only
in response to an ARTICLE command. So this needs to be an extra call in
DBZ, in addition to the 'fetch' or 'dbzfetch' calls, to be used in the
proposed extension to the NNTP ARTICLE command. Observe that if the
requested '$v=n' is present and linked to stored articles (for whatever
reason) then you will be given exactly that version, even if later ones
are stored as well.

5. NOTE that I have dropped the idea of having '$v=0', because you can
never be sure that the very first issue of the FAQ used it, so you have
to provide the versionless root as well. If someone asks for '$v=0' (or
any '$v=n') the algorithm I gave will still find it via the root. So we
don't care what people put in URLs.

6. You are supposed to cancel the replaced/superseded article. If you
REALLY want to keep the old ones around a little longer, then this
implementation will not work if you want the latest to be retrieved
automatically - you will have to invent something much more complicated.

7. Having said all that, here follows a brief account of the same thing,
but short enough to be included in our document (the convention being
that implementation issues are hinted at, rather than being described in
full detail).]

   Typically, a news database will index a Replacement article both by
   its "version-number" message identifier (containing a "$v=" tag
   followed by a random-dollars-sequence) and by its "root" version
   (without the "$v=" tag or any following random-dollars-sequence).
   Thus when a request for an article comes in that is not present under
   the version-number requested, any article that is present and indexed
   by the corresponding root version can be retrieved instead. The
   indexing mechanism needs to be such that, although the root version
   may have at times referred to many different articles, it is always
                          News Article Format                 April                  July 2001

   the current one that is retrieved.

        NOTE: The presence of a version-number in the message identifier
        of an article without a Replaces or Supersedes header causes no
        extra action (it is just an ordinary article). Observe also that
        if an article with the exact message identifier (even though it
        contains a version-number) is, for whatever reason, already
        present on the serving agent, that article will always be
        retrieved in preference to the one indexed by any root version.  The Message-Version NNTP extension

   The following Service Extension to the NNTP protocol is defined in
   accordance with the framework set out in [NNTP], and is to be
   registered with IANA.

   Name of the extension:                             Message-Version
   Extension Label (for the LIST EXTENSIONS command): MESSAGE-VERSION
   Additional keywords, syntax and parameters:        None

   In a server supporting this extension, the behaviour of the ARTICLE,
   HEAD, BODY and STAT commands when the parameter is a <message-id> is
   modified as follows.

   If the specified article is available on the server then it (or its
   Head, Body or Status as appropriate) is returned in the normal
   manner.  Otherwise, if a leftmost id-left-side of the <message-id>
   (the part before the '@') contains "$v=<n>", where <n> is an integer
   version number, that "$v=<n>"and everything following it is stripped
   from that id-left-side and the article (Head, Body or Status) with
   the stripped <message-id> is returned instead.  Otherwise (no article
   is available under the original, or any stripped, <message-id>), a
   430 response is given as usual.

        NOTE: If the client is concerned to know whether the article
        found was exactly the one requested or a replacement article
        corresponding to a stripped <message-id>, then it has only to
        compare the <message-id> requested with that returned in the 220
        (221, 222, or 223) response. The intent of this extension is to
        enable the retrieval of the current version of an article (such
        as a regularly posted FAQ) referenced by a "news:" URL [RFC-
        1738] which quotes the <message-id> of an earlier version.

        NOTE: This extension has no effect on the IHAVE command.  Examples

   Example 1. The first edition of a FAQ is posted with a message
   identifier of the form:  <examplegroup-faq@faq-site.example>. The
   next (but identical) version, a month later, has:

      Message-ID: <examplegroup-faq$v=1$A1b@faq-site.example>
      Replaces: <examplegroup-faq@faq-site.example>; disposition=repost
      Supersedes: <examplegroup-faq@faq-site.example>
                          News Article Format                 April                  July 2001

   Observe the inclusion of a Supersedes header as well, it being
   presumed that the Replaces header was not yet widely implemented at
   that time.

   The next one, another month later (and with some significant changes
   justifying the use of "replace" rather than "repost") has:

      Message-ID: <examplegroup-faq$v=2$B2b@faq-site.example>
      Replaces: <examplegroup-faq$v=1$A1b@faq-site.example>
         <examplegroup-faq@faq-site.example>; disposition=replace
      Supersedes: <examplegroup-faq$v=1$A1b@faq-site.example>

   The next one, another month later, has:

      Message-ID: <examplegroup-faq$v=3$C3c@faq-site.example>
      Replaces: <examplegroup-faq$v=2$B2b@faq-site.example>
         <examplegroup-faq$v=1$A1b@faq-site.example>; disposition=repost
      Supersedes: <examplegroup-faq$v=2$B2b@faq-site.example>

   Note that the only reason to include more than one message identifier
   in the Replaces is in case a site had missed the previous
   Replacement. It is hardly necessary with such a long interval between
   the postings.

   Under the above, on systems using the version-number system (which is
   optional) requests for any message identifier in the chain will
   always return the most recent. As such the URL "news:examplegroup-
   faq@faq-site.example" will always work, making it suitable to appear
   in HTML documents.

   Example 2. A user posts a message <myuniquepart@mysite.example> to
   the net.  She notices a typo and, 2 minutes later, posts with:

      Message-ID: <myuniquepart$v=1$xxx@mysite.example>
      Replaces: <myuniquepart@mysite.example>; disposition=revise

   3 minutes later she sees another typo, and posts:

      Message-ID: <myuniquepart$v=2$yyy@mysite.example>
      Replaces: <myuniquepart$v=1$xxx@mysite.example>
         <myuniquepart@mysite.example>; disposition=revise

   The two bad versions will be replaced with the 3rd, even if a site
   never sees the 2nd due to batching or feed problems (thus the use of
   two message identifiers is quite useful in this case, in
   contradistinction to the first example). Requests for the original
   will return the 3rd.

6.16.  Xref

   The Xref header is a local variant header ( which indicates where
   an article was filed by the last server to process it, and whether it
   is a Replacement (6.15) for an earlier article.

                          News Article Format                 April                  July 2001

      Xref-content      = [CFWS] server-name 1*( CFWS location )
      server-name       = path-identity  ; see 5.6.1
      location          = newsgroup-name ":" article-locator
                             [ CFWS ( "revise" / "repost" )
                               ":" article-locator ]
      article-locator   = 1*( %x21-7E ) ; US-ASCII printable characters

   The server-name is included so that software can determine which
   serving agent generated the header. The locations specify what
   newsgroups the article was filed under (which may differ from those
   in the Newsgroups header) and where it was filed under them. The
   exact form of an article-locator is implementation-specific.

        NOTE: The traditional form of an article-locator is a decimal
        number, with articles in each newsgroup numbered consecutively
        starting from 1. NNTP demands that such a model be provided, and
        much other software expects it, but it seems desirable to permit
        flexibility for unorthodox implementations.

   Whenever an Xref header is created by an agent for an article which
   includes a Replaces header with "disposition=revise" or
   "disposition=repost" (6.15), it SHOULD include, within the location
   field of each newsgroup in the Newsgroups header of whichever of the
   old articles referenced in that Replaces header is still current, a
   corresponding "revise:<old-article-locator>" or "repost:<old-
   article-locator>" for the oldest article known to be being replaced,
   where <old-article-locator> is the article-locator under which that
   oldest article was filed. If the Replaces header has a
   "disposition=replace" (explicit or implicit) the Xref header MUST NOT
   include any such reference to an <old-article-locator>.

        NOTE: This is to enable reading agents to avoid showing that
        article to users who have already read any of those older
        articles (see 6.15).  Because several replacements for a given
        article may arrive in the period between attempts by a reader to
        read a given newsgroup, it is useful to include the oldest one
        in the Xref header. The information necessary to determine this
        article can be obtained from the Xref header of the current
        version of the article just before it is deleted. Observe that a
        server that never received one of the replaced articles can
        still generate suitable information from whichever earlier
        version it actually has. This is why it is useful for a Replaces
        header to mention more than one earlier article, especially when
        replacements are being issued in quick succession.

        NOTE: "revise" and "repost" are case-insensitive.

   An agent inserting an Xref header into an article MUST delete any
   previous Xref header(s). A relaying agent MAY delete it before
   relaying, but otherwise it SHOULD be ignored (and usually replaced)
   by any relying or serving agent receiving it.

                          News Article Format                 April                  July 2001

   An agent MUST use the same serving-name in Xref headers as the path-
   identity it uses in Path headers.

6.17.  Lines

   The Lines header indicates the number of lines in the body of the

      Lines-content       = [CFWS] 1*digit

   The line count includes all body lines, including the signature if
   any, including empty lines (if any) at the beginning or end of the
   body, and including the whole of all Mime MIME message and multipart parts
   contained in the body (the single empty separator line between the
   headers and the body is not part of the body). The "body" here is the
   body as found in the posted article as transmitted by the posting

   This header is to be regarded as obsolete, and it will likely be
   removed entirely in a future version of this standard. In the
   meantime, its use is deprecated.

6.18.  User-Agent

   The User-Agent header contains information about the user agent
   (typically a newsreader) generating the article, for statistical
   purposes and tracing of standards violations to specific software
   needing correction. Although not one of the mandatory headers,
   posting agents SHOULD normally include it.

      User-Agent-content  = product-token *( CFWS product-token )
      product-token       = value ["/" product-version]  ; see 4.1
      product-version     = value

   This header MAY contain multiple product-tokens identifying the agent
   and any subproducts which form a significant part of the posting
   agent, listed in order of their significance for identifying the
   application. Product-tokens should be short and to the point - they
   MUST NOT be used for information beyond the canonical name of the
   product and its version.  Injecting agents MAY include product
   information for servers (such as "INN/1.7.2"), but serving and
   relaying agents MUST NOT generate or modify this header to list

        NOTE: Variations from [RFC 2616] which describes a similar
        facility for the HTTP protocol:

        1.    use of arbitrary text or octets from character sets other
              than US-ASCII in a product-token may require the use of a

        2.    "{" and "}" are allowed in a value (product-token and
              product-version) in Netnews,
                          News Article Format                 April                  July 2001

        3.    UTF-8 replaces ISO-8859-1 as charset assumption.

        NOTE: Comments should be restricted to information regarding the
        product named to their left such as platform information and
        should be concise. Use as an advertising medium (in the mundane
        sense) is discouraged.

6.18.1.  Examples

      User-Agent: tin/1.2-PL2
      User-Agent: tin/1.3-950621beta-PL0 (Unix)
      User-Agent: tin/unoff-1.3-BETA-970813 (UNIX) (Linux/2.0.30 (i486))
      User-Agent: tin/pre-1.4-971106 (UNIX) (Linux/2.0.30 (i486))
      User-Agent: Mozilla/4.02b7 (X11; I; en; HP-UX B.10.20 9000/712)
      User-Agent: Microsoft-Internet-News/4.70.1161
      User-Agent: Gnus/5.4.64 XEmacs/20.3beta17 ("Bucharest")
      User-Agent: Pluto/1.05h (RISC-OS/3.1) NewsHound/1.30
      User-Agent: inn/1.7.2
      User-Agent: telnet

        NOTE: This header supersedes the role performed redundantly by
        experimental headers such as X-Newsreader, X-Mailer, X-Posting-
        Agent, X-Http-User-Agent, and other headers previously used on
        Usenet for this purpose. Use of these experimental headers
        SHOULD be discontinued in favor of the single, standard User-
        Agent header which can be used freely both in Netnews and mail.

6.19.  Injector-Info

   The Injector-Info header SHOULD be added to each article by the
   injecting agent in order to provide information as to how that
   article entered the Netnews system and to assist in tracing its true

                          = path-identity
                          = posting-host-parameter /
                            posting-account-parameter /
                            posting-sender-parameter /
                            posting-logging-parameter /
                            ; for USENET-header-parameters see 4.1
                          = [CFWS] "posting-host" [CFWS] "=" [CFWS]
                              ( host-value /
                                DQUOTE host-value DQUOTE ) [CFWS]
      host-value          = dot-atom /
                            [ dot-atom ":" ]
                              ( dotted-quad / ; see [RFC 820]
                                ipv6-numeric ) ; see [RFC 2373]
                          =  [CFWS] "posting-account" [CFWS] "=" value
                          News Article Format                 April                  July 2001

                          = [CFWS] "sender" [CFWS] "=" [CFWS]
                              ( sender-value /
                                DQUOTE sender-value DQUOTE ) [CFWS]
      sender-value        = ( mailbox / "verified" )
                          = [CFWS] "logging-data" [CFWS] "=" value
                          = [CFWS] "posting-date" [CFWS] "=" [CFWS]
                              ( date-value /
                                DQUOTE date-value DQUOTE ) [CFWS]
      date-value          = 1*DIGIT [ ":" date-time ]

   An Injector-Info header MUST NOT be added to an article by any agent
   other than an injecting agent. Any Injector-Info header present when
   an article arrives at an injecting agent MUST be removed. In
   particular if, for some exceptional reason (8.2.2), an article gets
   injected twice, the Injector-Info header will always relate to the
   second injection.

   The path-identity MUST be the same as the path-identity prepended to
   the Path header by that same injecting agent which, following section
   5.6.2, MUST therefore be a fully qualified domain name (FQDN)
   mailable address.

   Although comments and folding of white space are permitted throughout
   the Injector-Info-content specification, it is RECOMMENDED that
   folding is not used within any header-parameter (but only before or
   after the ";" separating parameters), and that comments are only used
   following the last parameter. It is also RECOMMENDED that such
   parameters as are present are included in the order in which they
   have been defined in the syntax above.  An injecting agent SHOULD use
   a consistent form of this header for all articles emanating from the
   same or similar origins.

        NOTE: The effect of those recommendations is to facilitate the
        recognition of articles arising from certain designated origins
        (as in the so-called "killfiles" which are available in some
        reading agents). Observe that the order within the syntax has
        been chosen to place last those parameters which are most likely
        to change between successive articles posted from the same

        NOTE:  To comply with the overall "attribute = value" syntax of
        USENET-header-parameters, any value containing an ipv6-numeric,
        a date-time, a mailbox or any CFWS MUST be quoted using
        <DQUOTE>s (the quoting is optional in other cases).

        NOTE: This header is intended to replace various currently-used
        but nowhere-documented headers such as "NNTP-Posting-Host",
        "NNTP-Posting-Date" amd "X-Trace". Any of these headers present
        when an article arrives at an injecting agent SHOULD also be
        removed as above.

                          News Article Format                 April                  July 2001

6.19.1.  Usage of Injector-Info-header-parameters

   The purpose of these parameters is to enable the injecting agent to
   make assertions about the origin of the article, in fulfilment of its
   responsibilities towards the rest of the network as set out in
   section 8.2.  These assertions can then be utilized as follows:

   1. To enable the administrator of the injecting agent to respond to
      complaints and queries concerning the article. For this purpose,
      the parameters included SHOULD be sufficient to enable the
      administrator to identify its true origin (which parameters are
      best suited to this purpose will vary with the nature of the
      injecting site and of its relationship to the posters who use it -
      there is no benefit in including parameters which contribute
      nothing to this aim).  An administrator MAY, with those parameters
      where the syntax so allows, use cryptic notations interpretable
      only by himself if he considers it appropriate to protect the
      privacy of that origin.

   2. To enable relaying, serving and reading agents to recognize
      articles from origins which they might wish to reject, divert, or
      otherwise handle specially, for reasons of site policy.

   3. To enable the timely identification of spews af articles arising
      from a common origin.

   An injecting agent MUST NOT include any Injector-Info-header-
   parameter unless it has positive evidence of its correctness. An
   injecting agent MAY include other-header-parameters with x-token
   attributes which will assist in identifying the origin of the

      NOTE: It will be observed that the range of parameters provided
      allows much choice as to the precise manner in which an injecting
      agent fulfils its responsibilities. Whilst this standard does not
      seek to establish any preferences in this matter, administrators
      of injecting agents need to be aware of the privacy implications
      of the choices that they make.  The posting-host-parameter

   If a dot-atom is present, it MUST be a FQDN identifying the specific
   host from which the injecting agent received the article.
   Alternatively, an IP address (dotted-quad or ipv6-numeric) identifies
   that host. If both forms are present, then they MUST identify the
   same host, or at least have done so at the time the article was

        NOTE: It is commonly the case that this header identifies a
        dial-up point-of-presence, in which case a posting-account or
        logging-data may need to be consulted to find the true origin of
        the article.

                          News Article Format                 April                  July 2001  The posting-account-parameter

   This parameter identifies the source from which the injecting agent
   received the article. It MAY be in a cryptic notation understandable
   only by the administrator of the injecting agent, but it MUST be such
   that a given source always gives rise to the same posting-account (if
   the injecting agent is unable to meet that obligation, then it should
   use a posting-logging-parameter instead).  The posting-sender-parameter

   This parameter identifies the mailbox of the verified sender of the
   article (alternatively, it uses the token "verified" to indicate that
   at least any addr-spec in the Sender header of the article, or in the
   From header if the Sender header is absent, is correct).

        NOTE: An injecting agent is unlikely to be able to make use of
        this parameter except in cases where it is running on a machine
        which is aware of the user-space in which the posting agent is
        operating. This parameter should be used in preference to a
        posting-account-parameter in such situations.  The posting-logging-parameter

   This parameter contains information (typically a serial number or a
   session number) which will enable the true origin of the article to
   be determined by reference to logging information kept by the
   injecting agent.  The posting-date-parameter

   This parameter identifies the time at which the article was injected
   (as distinct from the Date header, which indicates when it was
   written). It is in the form of the number of seconds elapsed since
   January 1st 1970, optionally followed by a date-time which MUST
   indicate the same time.

6.19.2.  Example

         posting-account=client0002623; logging-data=2427;
         posting-date="965243133: Wed 2 Aug 2000 20:05:33 -0100 (BST)"

6.20.  Complaints-To

   The Complaints-To header is added to an article by an injecting agent
   in order to indicate the mailbox to which complaints concerning the
   poster of the article may be sent.

                          = mailbox
                          News Article Format                 April                  July 2001

   A Complaints-To header MUST NOT be added to an article by any agent
   other than an injecting agent. Any Complaints-To header present when
   an article arrives at an injecting agent MUST be removed. In
   particular if, for some exceptional reason (8.2.2), an article gets
   injected twice, the Complaints-To header will always relate to the
   second injection.

   The specified mailbox is for sending complaints concerning the
   behaviour of the poster of the article; it SHOULD NOT be used for
   matters concerning propagation, protocol problems, etc. In the
   absence of this header, such complaints should be sent to "usenet@"
   or "news@" the path-identity which was prepended to the Path header
   by the injecting agent following section 5.6.2.

6.21.  MIME headers

6.21.1.  Syntax

   The following headers, as defined within [RFC 2045] and its
   extensions, may be used within articles conforming to this standard.


   Insofar as the syntax for these headers, as given in [RFC 2045], does
   not specify precisely where whitespace and comments may occur
   (whether in the form of WSP, FWS or CFWS), the usage defined in this
   standard, and failing that in [MESSFOR], [RFC 2822], and failing that in [RFC
   822] MUST be followed. In particular, there MUST NOT be any WSP
   between a header-name and the following colon and there MUST be a SP
   following that colon.

   The meaning of the various MIME headers is as defined in [RFC 2045]
   and [RFC 2046], and in extensions registered in accordance with [RFC
   2048].  However, their usage is curtailed as described in the
   following sections.

6.21.2.  Content-Transfer-Encoding

   Posting agents SHOULD specify "Content-Transfer-Encoding: 8bit" for
   all articles not written in pure US-ASCII and not requiring full
   binary. They MAY use "8bit" encoding even when "7bit" encoding would
   have sufficed. They SHOULD specify "base64" when  Content-Type

   The Content-Type: "text/plain" is the content default type
   implies binary (i.e. content intended for machine, rather than human,

        NOTE: If a future extension to any news
   article, but the MIME standards were recommendations and limits on line lengths set out
   in section 4.5 Ought to
        provide be observed

   The acceptability of other subtypes of Content-Type: "text" (such as
   "text/html") is a more compact encoding matter of binary suited policy (see 1.1), and posters Ought Not
   to transport
        over an 8bit channel, it could be considered as an alternative
                          News Article Format                 April 2001

        to base64 once it had gained widespread acceptance.

   Posting agents SHOULD NOT specify encoding "quoted-printable", but
   reading agents MUST interpret that encoding correctly.  Encoding
   "binary" MUST NOT be used (except in cooperating subnets with
   alternative transport arrangements) because this standard does not
   mandate a transport mechanism that could support it.

   Injecting and relaying agents MUST NOT change the encoding of
   articles passed to them. Gateways SHOULD NOT change the encoding
   unless absolutely necessary.

6.21.3.  Content-Type

   The Content-Type: "text/plain" is the default type for any news
   article, but the recommendations and limits on line lengths set out
   in section 4.5 Ought to be observed

   The acceptability of other subtypes of Content-Type: "text" (such as
   "text/html") is a matter of policy (see 1.1), and posters Ought Not
   to use them unless established policy or custom in the particular
   hierarchies or groups involved so allows.  Moreover, even in those
   cases, for the benefit of readers who see use them unless established policy or custom in the particular
   hierarchies or groups involved so allows.  Moreover, even in those
   cases, for the benefit of readers who see it only in its transmitted
   form, the material SHOULD be "pretty-printed" (for example by
                          News Article Format                  July 2001

   restricting its line length as above and by keeping sequences which
   control its layout or style separate from the meaningful text).

   In the same way, Content-Types requiring special processing for their
   display, such as "application", "image", "audio", "video" and
   "multipart/related" are discouraged except in groups specifically
   intended (by policy or custom) to include them. Exceptionally, those
   application types defined in [RFC 1847] and [RFC 2015] and/or [RFC
   2015bis] for use within "multipart/signed" articles, and the type
   "application/pgp-keys" (or other similar types containing digital
   certificates) may be used
   freely but, contrary to [RFC 2015] and unless the article is intended
   to be sent by mail also, the Content-Transfer-Encoding SHOULD be left
   as "8bit" (or "7bit" as appropriate). freely.

   Reading agents SHOULD NOT, unless explicitly configured otherwise,
   act automatically on Application types which could change the state
   of that agent (e.g. by writing or modifying files), except in the
   case of those prescribed for use in control messages (7.1.2 and
   7.4.1).  Message/partial

   The Content-Type "message/partial" MAY be used to split a long news
   article into several smaller ones, but this usage ones.

        NOTE: This Content-Type is discouraged on not recommended for textual articles
        because the grounds that Content-Type, and in particular the charset, of the
        complete article cannot be determined by examination of the
        second and subsequent parts, and hence it is not possible to
        read them as separate articles (except when they are written in
        pure US-ASCII). Moreover, for full compliance with [RFC 2046] it
        would be necessary to use the "quoted-printable" encoding to
        ensure the material was 7bit-safe.  In any case, breaking such
        long texts into several parts is usually unnecessary, since
        modern transport agents should have no difficulty in handling
        articles of arbitrary length.


        On the other hand, "message/partial" may be useful for binaries
        of excessive length, since reading of the individual parts on
        their own is not required and they would in any case be encoded
        in a manner that was 7bit-safe.

   IF this feature Content-Type is used, then the "id" parameter SHOULD be in
   the form of a unique message identifier (but different from that in
   the Message-ID header of any of the parts).  Contrary to the
                          News Article Format                 April 2001

   requirements specified in [RFC 2046], the Transfer-Encoding SHOULD be
   set to "8bit" at least in each part that requires it. The second and subsequent
   parts SHOULD contain References headers referring to all the previous
   parts, thus enabling reading agents with threading capabilities to
   present them in the correct order. Reading agents MAY then provide a
   facility to recombine the parts into a single article (but this
   standard does not require them to do so).  Message/rfc822

   The Content-Type "message/rfc822" should be used for the
   encapsulation (whether as part of another news article or, more
   usually, as part of a mail message) of complete news articles which
                          News Article Format                  July 2001

   have already been posted to Netnews and which are for the information
   of the recipient, and do not constitute a request to repost them.

   In the case where the encapsulated article has Content-Transfer-
   Encoding "8bit", it will be necessary to change that encoding if it
   is to be forwarded over some mail transport that only supports
   "7bit". However, this should not be necessary for any mail transport
   that supports the 8BITMIME feature [SMTP]. [RFC 2821].  Moreover, where the
   headers of the encapsulated article contain any UTF8-xtra-chars
   (2.4), it may not be possible to transport them over mail transports
   even where 8BITMIME is supported. In such cases, it will be necessary
   to encode those headers as provided in [RFC 2047] (notwithstanding
   that such usage is deprecated for news headers by this standard, and
   actually forbidden in the case of the Newsgroups header).

   In the event that the encapsulated article has to be encoded for
   either of these reasons, it may be necessary to reverse that encoding
   if certain forms of digital signatures have been employed, or if the
   article is to be reintroduced into some Netnews system (however, in
   the latter case, the Content-Type "application/news-transmission"
   should have been used instead).

        NOTE: It is likely, though not guaranteed, that headers
        containing UTF8-xtra-chars will pass safely through mail
        transports supporting 8BITMIME if the "message/rfc822" object is
        sent as an attachment (i.e.  as a part of a multipart) rather
        than as the top-level body of the mail message. Moreover, it is
        anticipated that future extensions to the mail standards will
        permit headers containing UTF8-xtra-chars to be carried without
        further ado over conforming transports.
[In fact, of current transports supporting 8BITMIME, only sendmail will
have problems with UTF-8 in top-level headers.]  Message/external-body

   The Content-Type "message/external-body" could be apropriate for
   texts which it would be uneconomic (in view of the likely readership)
   to distribute to the entire network.

                          News Article Format                 April 2001  Multipart types

   The Content-Types "multipart/mixed", "multipart/parallel" and
   "multipart/signed" may be used freely in news articles.  However,
   except where policy or custom so allows, the Content-Type:
   "multipart/alternative" SHOULD NOT be used, on account of the extra
   bandwidth consumed and the difficulty of quoting in followups, but
   reading agents MUST accept it.

   The Content-Type: "multipart/digest" is commended for any article
   composed of multiple messages more conveniently viewed as separate
   entities, thus enabling reading agents to move rapidly between them.
   The "boundary" should be composed of 28 hyphens (US-ASCII 45) (which
   makes each boundary delimiter 30 hyphens, or 32 for the final one) so
   as to enable reading agents which currently support the digest usage
                          News Article Format                  July 2001

   described in [RFC 1153] to continue to operate correctly.
[Actually, this conflicts with some present digest usage (such as the
news.answers rules), but should still be the right way to go. There
remains go. There
remains the possibility that future MIME-compliant readers could enable
one to proceed directly to some particular message by clicking on it in
a table of contents, but that feature is not yet supported by the
current MIME standards.]

        NOTE: The various recomendations given above regarding the usage
        of particular Content-Types apply also to the individual parts
        of these multiparts.

6.21.3.  Content-Transfer-Encoding

   "Content-Transfer-Encoding: 7bit" is sufficient for article bodies
   (or parts of multiparts) written in pure US-ASCII (or most other
   material representable in 7 bits).  Posting agents SHOULD specify
   "Content-Transfer-Encoding: 8bit" for all other cases unless there
   are pressing reasons to do otherwise. They MAY use "8bit" encoding
   even when "7bit" encoding would have sufficed. Examples of such
   pressing reasons are the following:

   1. The content type implies that the content is (or may be) "8bit-
      unsafe"; i.e.  it may contain octets equivalent to the US-ASCII
      characters CR or LF (other than in the combination CRLF) or NUL.
      In that case one of the Content-Transfer-Encodings "base64" or
      "quoted-printable" MUST be used, and reading agents MUST be able
      to handle both of them. Encoding "binary" MUST NOT be used (except
      in cooperating subnets with alternative transport arrangements)
      because this standard does not mandate a transport mechanism that
      could support it.

        NOTE: If a future extension to the MIME standards were to
        provide a more compact encoding of binary suited to transport
        over an 8bit channel, it could be considered as an alternative
        to base64 once it had gained widespread acceptance.

   2. It is often the case that "application" Content-Types are textual
      in nature, and intelligible to humans as well as to machines, and
      where this state can be recognized by the posting agent (either
      through knowledge of the particular application type or by
      testing) the material SHOULD NOT be treated as 8bit-unsafe; this
      has the added benefit, where the posting agent uses other than
      CRLF for line endings internally, of automatically ensuring that
      line endings are processed correctly during transport.

      If, on the other hand, the posting agent recognizes that the
      material is not textual, or cannot reasonably determine it to be
      so, then the material MUST be encoded as for 8bit-unsafe (however,
      in that case, it is the responsibility of the agent generating the
      material to ensure that lines endings, if any, are represented

                          News Article Format                  July 2001

        NOTE: All the application types defined by this standard, namely
        "application/news-transmission", "application/news-groupinfo"
        and "application/news-checkgroups" are textual, and indeed
        designed for human reading.

   3. Although the "text" Content-Types should normally be encoded as
      8bit (or 7bit), if the character set specified by the "charset="
      parameter can include the 3 disallowed octets, then the material
      MUST be encoded as for 8bit-unsafe.  This is most likely to arise
      in the case of 16-bit character sets such as UTF-16 ([UNICODE3.1]
      or [ISO/IEC 10646]).  In addition, where it is known that the
      material is subseqently to be gatewayed from news to mail (8.8),
      the encoding "quoted-printable" MAY be used (otherwise the gateway
      might have to re-encode it itself).

   4. Some protocols REQUIRE the use of a particular Content-Transfer-
      Encoding. In particular, the authentication protocol based on
      [Open]PGP defined in [RFC 2015] and/or [RFC 2015bis] mandates the
      use of one of the encodings "quoted-printable" or "base64".
      Whilst posters might be tempted to risk the use of "8bit" or
      "7bit" encodings (and indeed the referenced standard recommends
      that signed messages using those encodings be accepted and
      interpreted), they should be warned that differences in the
      treatment of trailing whitespace between OpenPGP [RFC 2440] and
      earlier versions of PGP may render signatures written with the one
      unverifiable by the other; and, moreover, Usenet articles are very
      likely to include trailing whitespace in the possibility form of a personal
      signature (4.3.2).
[It is to be hoped that future Mime-compliant readers could enable
one [RFC 2015bis] will have progressed to proceed directly a full RFC
by the time this draft is finalized.]

   5. The Content-Type message/partial [RFC 2046] is required to some particular use
      encoding "7bit" (the encapsulated complete message by clicking on it in
a table of contents, may itself use
      encoding "quoted-printable" or "base64", but that feature information is not yet supported by
      only conveyed along with the
curremt Mime standards.] first of the partial parts).

        NOTE: The various recomendations given above regarding Although there would actually be no problem using encoding
        "8bit" in a pure Netnews (as opposed to mail) environment, this
        standard discourages (see the usage use of particular Content-Types apply also "message/partial"
        except for binary material, which will be encoded to pass
        through "7bit" in any case.

   Injecting and relaying agents MUST NOT change the individual parts encoding of these multiparts.
   articles passed to them. Gateways SHOULD NOT change the encoding
   unless absolutely necessary.

6.21.4.  Character Sets

   In principle, any character set may be specified in the "charset="
   parameter of a content type. However, only those character sets (and
   the corresponding parts of UTF-8) should be used which are
   appropriate for the customary language(s) of the hierarchy or
   newsgroup concerned (whose readers could be expected to possess
   agents capable of displaying them).

                          News Article Format                  July 2001

6.21.5.  Content Disposition

   Reading agents Ought to honour any Content-Disposition header that is
   provided (in particular, they Ought to display any part of a
   multipart for which the disposition is "inline", possibly
   distinguished from adjacent parts by some suitable separator). In the
   absence of such a header, the body of an article or any part of a
   multipart with Content-Type "text" Ought to be displayed inline.
   Followup agents which quote parts of a precursor (see 4.3.2) Ought
   initially to include all parts of the precursor that were displayed
   inline, as if they were a single part.

6.21.6.  Definition of some new Content-Types

   This standard defines (or redefines) several new Content-Types, which
   require to be registered with IANA as provided for in [RFC 2048].
   For "application/news-groupinfo" see 7.1.2, for "application/news-
   checkgroups" see 7.4.1, and for "application/news-transmission" see
                          News Article Format                 April 2001
   the following section.  Application/news-transmission

   The Content-Type "application/news-transmission" is intended for the
   encapsulation of complete news articles where the intention is that
   the recipient should then inject them into Netnews. This Application
   type SHOULD be used when mailing articles to moderators and to mail-
   to-news gateways (see 8.2.2).

        NOTE: The benefit of such encapsulation is that it removes
        possible conflict between news and email headers and it provides
        a convenient way of "tunnelling" a news article through a
        transport medium that does not support 8bit characters.

   The MIME content type definition of "application/news-transmission"

   MIME type name:           application
   MIME subtype name:        news-transmission
   Required parameters:      none
   Optional parameters:      usage=moderate
   Encoding considerations:  A transfer-encoding (such as Quoted-
                             Printable or Base64) different from that of
                             the article transmitted MAY be supplied
                             (perhaps en route) to ensure correct
                             transmission over some 7bit transport
   Security considerations:  A news article may be a "control message",
                             which could have effects on the recipient
                             host's system beyond just storage of the
                             article. However, such control messages
                             also occur in normal news flow, so most
                             hosts will already be suitably defended
                          News Article Format                  July 2001

                             against undesired effects.
   Published specification:  [USEFOR]
   Body part:                A complete article or proto-article, ready
                             for injection into Netnews, or a batch of
                             such articles.

        NOTE: It is likely that the recipient of an "application/news-
        transmission" will be a specialised gateway (e.g. a moderator's
        submission address) able to accept articles with only one of the
        three usage parameters "moderate", "inject" and "relay", hence
        the reason why they are optional, being redundant in most
        situations. Nevertheless, they MAY be used to signify the
        originator's intention with regard to the transmission, so
        removing any possible doubt.

   When the parameter "relay" is used, or implied, the body part MAY be
   a batch of articles to be transmitted together, in which case the
   following syntax MUST be used.

                          News Article Format                 April 2001

      batch             = 1*( batch-header article )
      batch-header      = "#!" SP "rnews" SP article-size CRLF
      article-size      = 1*digit

   where the "rnews" is case-sensitive. Thus a batch is a sequence of
   articles, each prefixed by a header line that includes its size. The
   article-size is a decimal count of the octets in the article,
   counting each CRLF as one octet regardless of how it is actually

        NOTE: Despite the similarity of this format to an executable
        UNIX script, it is EXTREMELY unwise to feed such a batch into a
        command interpreter in anticipation of it running a command
        named "rnews"; the security implications of so doing would be
        disastrous.  Message/news withdrawn

   The Content-Type "message/news", as previously registered with IANA,
   is hereby obsoleted and should be withdrawn. It was never widely
   implemented, and its default treatment as "application/octet-stream"
   by agents that did not recognise it was counter productive. The
   Content-Type "message/rfc822" SHOULD be used in its place, as already
   described above.

6.22.  Obsolete Headers

   Persons writing new agents SHOULD ignore any former meanings of the
   following headers:

                          News Article Format                  July 2001

7.  Control Messages

   The following sections document the control messages.  "Message" is
   used herein as a synonym for "article" unless context indicates
   otherwise.  Group control messages are the sub-class of control
   messages that request some update to the configuration of the groups
   known to a serving agent, namely "newgroup".  "rmgroup", "mvgroup"
   and "checkgroups", plus any others created by extensions to this

   All of the group control messages MUST have an Approved header
   (6.14).  Moreover, in those hierarchies where appropriate
   administrative agencies exist (see 1.1), group control messages Ought
   Not to be issued except as authorized by those agencies.
[They SHOULD also use one of the authentication mechanisms which we may
define when we get a Round Tuit.]
                          News Article Format                 April 2001

   The Newsgroups header of each control message MUST SHOULD include the
   newsgroup-name(s) for the group(s) affected (i.e. groups to be
   created, modified or removed, or containing articles to be canceled).
   This is to ensure that the message progagates to all sites which
   receive (or would receive) that group(s). It MAY include other
   newsgroup-names so as to improve propagation (but this practice may
   cause the control message to propagate also to places where it is
   unwanted, so it should not be regarded as exceptional rather than normal).

   The used without good reason).

   For convenience, the descriptions below are generally phrased in terms suggesting
   mandatory actions, but any or all on the assumption
   that control messages will be honoured by sites receiving them.
   Naturally, this does not apply where they have not been issued by the
   appropriate administrative agencies (and sites SHOULD take such steps
   as are reasonable practicable to validate their authenticity).
   Moreover, acceptance of these such messages MAY be subject to local
   administrative restrictions, and MAY be denied or referred to an
   administrator for approval (either as a class or on a case-by-case
   basis).  Analogously, where the description below specifies that a
   message or portion thereof is to be ignored, this action MAY include
   reporting it to an administrator.

   Relaying Agents MUST propagate even control messages that they do not

   In the following sections, each type of control message is defined
   syntactically by defining its verb, its arguments, and possibly its

7.1.  The 'newgroup' Control Message

      newgroup-verb       = "newgroup"
      newgroup-arguments  = CFWS newsgroup-name [ CFWS newgroup-flag ]
      newgroup-flag       = "moderated"

   The "newgroup" control message requests that the specified group be
   created or changed. The newgroup-flag "moderated" If the request is appended to mark honoured, or if the group as moderated. The absence of this flag marks
   already exists on the serving agent, and if the newgroup-flag
                          News Article Format                  July 2001

   "moderated" is present, then the group MUST be marked as
   unmoderated. moderated,
   and vice versa. "Moderated" is the only such flag defined by this
   standard; other flags MAY be defined for use in cooperating subnets,
   but newgroup messages containing them MUST NOT be acted on outside of
   those subnets.

        NOTE: Specifically, some alternative flags such as "y" and "m",
        which are sent and recognised by some current software, are NOT
        part of this standard.  Moreover, some existing implementations
        treat any flag other than "moderated" as indicating an
        unmoderated newsgroup. Both of these usages are contrary to this

   The message body comprises or includes a "application/news-groupinfo"
   (7.1.2) part containing machine- and human-readable information about
   the group.


   It is REQUIRED that the newsgroup-name MUST conform conforms to all requirements
   set out in section 5.5, and it is 5.5.  This includes the responsibility of restrictions as to the
   permitted characters, and the requirement that they be invariant
   under NFKC normalization. It is essential that those who issue
   newgroup message
   issuer messages are aware of their responsibility to ensure enforce this (since
   requirement, since some of those requirements conditions are hard to enforce mechanically). Moreover,

   Additionally, the newsgroup-name Ought to conform to whatever
   policies have been established by the administrative agency, if any,
   for that hierarchy.

                          News Article Format                 April 2001 Serving agents SHOULD, insofar as they are
   conveniently able to detect them, reject all newgroup messages not
   meeting those requirements.

   The newgroup command is also used to update the newsgroups-line or
   the moderation status of a group.

7.1.1.  The Body of the 'newgroup' Control Message

   The body of the newgroup message contains the following subparts,
   preferably in the order shown:

   1. An "application/news-groupinfo" part (7.1.2) containing the name
      and newsgroups-line of the group(s). This part MUST be present.

   2. Other parts containing useful information about the background of
      the newsgroup message (typically of type "text/plain").

   3. Parts containing initial articles for the newsgroup. See section
      7.1.3 for details.

   In the event that there is only the single (i.e. application/news-
   groupinfo) subpart present, it will suffice to include a "Content-
   Type:  application/news-groupinfo" amongst the headers of the control
   message.  Otherwise, a "Content-Type: multipart/mixed header" will be
   needed, and each separate part will then need its own Content-Type

                          News Article Format                  July 2001

7.1.2.  Application/news-groupinfo

   The "application/news-groupinfo" body part contains brief information
   about a newsgroup, i.e. the group's name, it's newsgroup-description
   and the moderation-flag.

        NOTE: The presence of the newsgroups-tag "For your newsgroups
        file:" is intended to make the whole newgroup message compatible
        with current practice as described in [Son-of-1036].

   The MIME content type definition of "application/news-groupinfo" is:

   MIME type name:           application
   MIME subtype name:        news-groupinfo
   Required parameters:      none
   Disposition:              by default, inline
   Encoding considerations:  "7bit" or "8bit" is sufficient and MUST be
                             used to maintain compatibility.
   Security considerations:  this type MUST NOT be used except as part
                             of a control message for the creation or
                             modification of a Netnews newsgroup
   Published specification:  [USEFOR]

   The content of the "application/news-groupinfo" body part is defined

      groupinfo-body      = [ newsgroups-tag CRLF ]
                               1*( newsgroups-line CRLF )
                          News Article Format                 April 2001
      newsgroups-tag      = %x46.6F.72 SP %x79.6F.75.72 SP
                               %x6E. SP
                               ; case sensitive
                               ; "For your newsgroups file:"
      newsgroups-line     = newsgroup-name
                               [ 1*HTAB newsgroup-description ]
                               [ 1*WSP moderation-flag ]
                          = 1*( [WSP] utext)
      moderation-flag     = %x28.4D.6F.
                               ; case sensitive "(Moderated)"
   The whole groupinfo-body is intended to be interpreted as a text
   written in the UTF-8 character set.

   The "application/news-groupinfo" is used in conjunction with the
   "newgroup" (7.1) and "mvgroup" (7.3) control messages.  The
   newsgroup-name(s) in the newsgroups-line MUST agree with the
   newsgroup-name(s) in the "newgroup" or "mvgroup" control message (and
   thus there cannot be more than a single newsgroups-line except in the
   case of a "mvgroup" control message affecting a whole
   (sub)hierarchy).  The Content-Type "application/news-groupinfo" MUST
   NOT be used except as a part of such control messages.  Although
   optional, the newsgroups-tag SHOULD be included until such time as
   this standard has been widely adopted, to ensure compatibility with
   present practice.

                          News Article Format                  July 2001

   Moderated newsgroups MUST be marked by appending the case sensitive
   text " (Moderated)" at the end. It is NOT recommended that the
   moderator's email address be included in the newsgroup-description as
   has sometimes been done.

   Although, in accordance with [MESSFOR] [RFC 2822] and section 4.5 of this
   standard, a newsgroups-line could have a maximum length of 998
   octets, as a matter of policy a far lower limit, expressed in
   characters, Ought to be set. The current convention is to limit its
   length so that the newsgroup-name, the HTAB(s) (interpreted as 8-
   character tabs that takes one at least to column 24) and the
   newsgroup-description (excluding any moderation-flag) fit into 79
   characters.  However, this standard does not seek to enforce any such
   rule, and reading agents SHOULD therefore enable a newsgroups-line of
   any length to be displayed, e.g. by wrapping it as required.

        NOTE: The newsgroups-line is intended to provide a brief
        description of the newsgroup, written in the UTF-8 character
        set.  Since newsgroup-names are required to be expressed in
        UTF-8 when they appear in headers, and since [NNTP] requires the
        use of UTF-8 when such a description is transmitted by the LIST
        NEWSGROUPS command, it would also be convenient for servers that
        keep a "newsgroups" file to store them in that form, so as to
        avoid unnecessary conversions.

                          News Article Format                 April 2001

7.1.3.  Initial Articles

   Some subparts of a "newgroup" or "mvgroup" control message MAY
   contain an initial set of articles to be posted to the affected
   newsgroup(s) as soon as it has been created. These parts are
   identified by having the Content-Type "application/news-
   transmission", possibly with the parameter "usage=inject".  The body
   of each such part should be a complete proto-article, ready for
   posting. This feature is intended for the posting of charters,
   initial FAQs and the like to the newly formed group(s).

   The Newsgroups header of the proto-article MUST include the
   newsgroup-name of the newly created group (or one of them, if more
   than one). It MAY include other newsgroup-names. If the proto-article
   includes a Message-ID header, the message indentifier in it MUST be
   different from that of any existing article and from that of the
   control message as a whole, though it MAY be derived from it by
   appending "$p=<n>", where <n> is an integer part number (see also, immediately after its id-left-side (i.e.  before the "@").
   Alternatively such a message identifier MAY be derived by the
   injecting agent when the proto-article is posted. The proto-article
   SHOULD include the header "Distribution: local".

   The proto-article SHOULD be injected at the serving agent that
   processes the control message AFTER the newsgroup(s) in question has
   been created. It MUST NOT be injected if the newsgroup is not, in
   fact, created (for whatever reason). It MUST NOT be submitted to any
   relaying agent for transmission beyond the server(s) upon which the
   newsgroup creation has just been effected (in other words, it is to
                          News Article Format                  July 2001

   be treated as having a "Distribution: local" header, whether such a
   header is actually present or not).

        NOTE: The "$p=<n>" convention, if applied uniformly, should
        ensure that initial articles relayed beyond the local server in
        contravention of the above prohibition will not propagate in
        competition with similar copies injected at other local servers.

        NOTE: It is not precluded that the proto-article is itself a
        control message or other type of special article, to be
        activated only upon creation of the new newsgroup. However,
        except as might arise from that possibility, any
        "application/news-transmission" within some nested "multipart/*"
        structure within the proto-article is not to be activated.

7.1.4.  Example

   A "newgroup" with bilingual charter and policy information:

      From: "example.all Administrator" <admin@example.invalid>
      Newsgroups: example.admin.groups,example.admin.announce
      Date: 27 Feb 1997 12:50:22 +0200
      Subject: cmsg newgroup moderated
      Approved: admin@example.invalid
      Control: newgroup moderated
                          News Article Format                 April 2001
      Message-ID: <>
      Content-Type: multipart/mixed; boundary="nxtprt"
      Content-Transfer-Encoding: 8bit

      This is a MIME control message.
      Content-Type: application/news-groupinfo

      For your newsgroups file:      About the example.* groups (Moderated)

      Content-Type: application/news-transmission

      From: "example.all Administrator" <admin@example.invalid>
      Subject: Charter for
      Message-ID: <$p=1@example.invalid>
      Distribution: local
      Content-Type: multipart/alternative ;
         differences = content-language ;
         boundary = nxtlang

      Content-Type: text/plain; charset=us-ascii
      Content-Transfer-Encoding: 7bit
      Content-Language: en

      The group contains regularly posted
                          News Article Format                  July 2001

      information on the example.* hierarchy.

      Content-Type: text/plain; charset=iso-8859-1
      Content-Transfer-Encoding: 8bit
      Content-Language: de

      Die Gruppe enthaelt regelmaessig versandte
      Informationen ueber die example.*-Hierarchie.

7.2.  The 'rmgroup' Control Message

      rmgroup-verb        = "rmgroup"
      rmgroup-arguments   = CFWS newsgroup-name

   The "rmgroup" control message requests that the specified group be
   removed from the list of valid groups. The Content-Type of the body
   is unspecified; it MAY contain anything, usually an explanatory text.

        NOTE: It is entirely proper for a serving agent to retain the
        group until all the articles in it have expired, provided that
        it ceases to accept new articles.

                          News Article Format                 April 2001

7.2.1.  Example

   Plain "rmgroup":

      From: "example.all Administrator" <admin@example.invalid>
      Newsgroups: example.admin.groups, example.admin.announce
      Date: 4 Jul 1997 22:04 -0900 (PST)
      Subject: cmsg rmgroup example.admin.obsolete
      Message-ID: <rm-example.admin.obsolete-19970730@example.invalid>
      Approved: admin@example.invalid
      Control: rmgroup example.admin.obsolete

      The group example.admin.obsolete is obsolete. Please remove it
      from your system.

7.3.  The 'mvgroup' Control Message

      mvgroup-verb      = "mvgroup"
      mvgroup-arguments = CFWS ( mvgrp-groups / mvgrp-hrchy )
      mvgrp-groups      = newsgroup-name
                             CFWS newsgroup-name [ CFWS newgroup-flag ]
      mvgrp-hrchy       = groupnamepart ".*" CFWS groupnamepart ".*"
      groupnamepart     = newsgroup-name    ; syntactically

7.3.1.  Single group

   The "mvgroup" control message requests that the first specified group
   be moved to the second specified group. The message body MUST contain
   a "application/news-groupinfo" (7.1.2) containing machine- and
                          News Article Format                  July 2001

   human-readable information about the new group, and possibly other
   subparts as for a newgroup control message.

   When this message is received, and the new group SHOULD be does not already
   exist, it is created (and MUST be moderated if a newgroup-flag
   "moderated" is present) and all existing articles SHOULD be copied or
   moved to the new group; then the old, now empty group SHOULD be

   If the old group does not exist, the message is ignored unless the
   new group does not exist either, in which case the message SHOULD be
   treated as if it had been an equivalent "newgroup" message.

   If both groups exist, the groups MAY be "merged". If this is done, it
   MUST be done correctly, i.e. implementations MUST take care that the
   messages in the group being deleted are renumbered accordingly to
   avoid overwriting articles in one group with those of the other, and
   that crossposted articles do not appear twice. Otherwise, the old
   group is just removed.

        NOTE: Due to the severe difficulties of implementing this
        merging, those proposing to merge existing groups using this
        control message should be aware that it may not be implemented
        on many (if not most) sites, and should therefore be prepared
        for such disruption as may ensue.

                          News Article Format                 April 2001

   An indication that the old group was replaced by the new group MAY be
   retained by the serving agent so that continuity of service may be
   maintained, and clients made aware of the new arrangements.

        NOTE: Some serving agents that use an "active" file permit an
        entry of the form "oldgroup xxx yyy =newgroup", which enables
        any articles arriving for oldgroup to be diverted to newgroup,
        and could even enable users already subscribed to oldgroup to
        receive articles from newgroup instead.

   In all cases, the information conveyed in the "application/news-
   groupinfo" body part is applied to the new group.

   Until most serving agents conform to this standard, whenever a
   mvgroup control message for a single group is issued, a corresponding
   pair of rmgroup and newgroup control messages SHOULD be issued a few
   days later.

7.3.2.  Multiple Groups

   If the two names ends with the character sequence ".*", the newgroup
   message requests that a whole (sub)hierarchy be moved.  The same
   procedure as for single groups (7.3.1) applies to each matched group,
   except that the moderation status of each old group MUST be copied to
   the corresponding new group.

                          News Article Format                  July 2001

   To avoid recursion, the new groups' names MUST NEVER match the old
   groups' name pattern; i.e., moving a whole (sub)hierarchy to a
   subhierarchy of the original hierarchy is explicitly disallowed.

   Until most serving agents conform to this standard, whenever a
   mvgroup control message for multiple groups is issued, a
   corresponding set of rmgroup and newgroup control messages for all
   the affected groups SHOULD be issued a few days later.

7.3.3.  Examples

   Plain "mvgroup":

      From: "example.all Administrator" <admin@example.invalid>
      Newsgroups: example.admin.groups, example.admin.announce
      Date: 30 Jul 1997 22:04 -0500 (EST)
      Subject: cmsg mvgroup example.oldgroup example.newgroup moderated
      Message-ID: <mvgroup-example.oldgroup-19970730@example.invalid>
      Approved: admin@example.invalid
      Control: mvgroup example.oldgroup example.newgroup moderated
      Content-Type: multipart/mixed; boundary=nxt

      Content-Type: application/newgroupinfo

      For your newsgroups file:

                          News Article Format                 April 2001
      example.newgroup        The new replacement group (Moderated)


      The moderated group example.oldgroup is replaced by
      example.newgroup. Please update your configuration.

   More complex "mvgroup" for a whole hierarchy:

   The charter of  the group contained a reference to, which is also being moved. So the charter is

      From: "example.all Administrator" <admin@example.invalid>
      Newsgroups: example.admin.groups, example.admin.announce
      Date: 30 Jul 1997 22:04 -0500 (EST)
      Subject: cmsg mvgroup* example.conversation
      Message-ID: <>
      Approved: admin@example.invalid
      Control: mvgroup* example.conversation
      Content-Type: multipart/mixed; boundary=nxt

      Content-Type: application/news-groupinfo

      For your newsgroups file:
      example.conversation.boring     Boring conversations
                          News Article Format                  July 2001

      example.conversation.better     Better conversations
      example.conversation.jokes      Funny stuff
      example.conversation.jokes.d    Discussion of funny stuff

      Content-Type: application/news-transmission

      Newsgroups: example.conversation.jokes
      From: "example.all Administrator" <admin@example.invalid>
      Subject: Charter for renamed group example.conversation.jokes
      Distribution: local
      Message-ID: <$p=1@example.invalid>

      This group is to publish jokes and other funny stuff.
      Discussions about the articles posted here should be redirected
      to example.conversation.jokes.d; adding a Followup-To: header
      is recommended.


7.4.  The 'checkgroups' Control Message

   The "checkgroups" control message contains a list of all the valid
   groups in a complete hierarchy.

                          News Article Format                 April 2001

      checkgroup-verb     = "checkgroups"
      checkgroup-arguments= [ chkscope ] [ chksernr ]
      chkscope            = 1*( CFWS ["!"] newsgroup-name )
      chksernr            = CFWS "#" 1*DIGIT

   The chkscope parameter(s) specifies the (sub)hierarchy(s) for which
   this "checkgroups" message applies. The chksernr parameter is a
   serial number, which can be any positive integer (e.g. just numbered
   or the date in YYYYMMDD).  It SHOULD increase by an arbitrary value
   with every change to the group list and MUST NOT ever decrease.

        NOTE: This was added to circumvent security problems in
        situations where the Date header cannot be authenticated.


      Control: checkgroups de !de.alt #248

        NOTE: Some existing software does not support the "chkscope"
        parameter.  Thus a "checkgroups" message SHOULD also contain the
        groups of other subhierarchies the sender is not responsible
        for. "New" software MUST ignore groups which do not fall into
        the scope of the "checkgroups" message.

   If no scope for the checkgroups message is given, it applies to all
   hierarchies for which group statements appear in the message.

                          News Article Format                  July 2001

   The body of the message has the Content-Type "application/news-
   checkgroups".  It asserts that the newsgroups it lists are the only
   newsgroups in the specified hierarchies.

        NOTE: The checkgroups nessage is intended to synchronize the
        list of newsgroups stored by a serving agent, and their
        newsgroup-descriptions, with the lists stored by other serving
        agents throughout the network. However, it might be inadvisable
        for the serving agent actually to create or delete any
        newsgroups without first obtaining the approval of its
        administrators for such proposed actions.

7.4.1.  Application/news-checkgroups

   The "application/news-checkgroups" body part contains a complete list
   of all the newsgroups in a hierarchy, their newsgroup-descriptions
   and their moderation status.

   The MIME content type definition of "application/news-checkgroups"

   MIME type name:           application
   MIME subtype name:        news-checkgroups
   Required parameters:      none
   Disposition:              by default, inline
   Encoding considerations:  "7bit" or "8bit" is sufficient and MUST be
                             used to maintain compatibility.

                          News Article Format                 April 2001
   Security considerations:  this type MUST NOT be used except as part
                             of a checkgroups control message

   The content of the "application/news-checkgroups" body part is
   defined as:

      checkgroups-body    = *( valid-group CRLF )
      valid-group         = newsgroups-line ; see 7.1.2
   The whole checkgroups-body is intended to be interpreted as a text
   written in the UTF-8 character set.

   The "application/news-checkgroups" content type is used in
   conjunction with the "checkgroups" control message (7.4).

        NOTE: The possibility of removing a complete hierarchy by means
        of an "invalidation" line beginning with a '!' is no longer
        provided by this standard. The intent of the feature was widely
        misunderstood and it was misused more often than it was used
        correctly. The same effect, if required, can now be obtained by
        the use of an appropriate chkscope argument in conjunction with
        an empty checkgroups-body.

7.5.  Cancel

   The cancel message requests that a target article be "canceled" i.e.
   be withdrawn from circulation or access. A cancel message may be
   issued in the following circumstances.

                          News Article Format                  July 2001

   1. The poster of an article (or, more specifically, any entity
      mentioned in the From header or the Sender header, whether or not
      that entity was the actual poster) is always entitled to issue a
      cancel message for that article, and serving agents SHOULD honour
      such requests. Posting agents SHOULD facilitate the issuing of
      cancel messages by posters fulfilling these criteria.

   2. The agent which injected the article onto the network (more
      specifically, the entity identified by the path-identity in front
      of the leftmost '%' delimeter in the Path header (5.6) or in the
      Injector-Info header (6.19) and, where appropriate, the moderator
      (more specifically, any entity mentioned in the Approved header)
      is always entitled to issue a cancel message for that article, and
      serving agents SHOULD honour such requests.

   3. Other entities MAY be entitled to issue a cancel message for that
      article, in circumstances where established policy for any
      hierarchy or group in the Newsgroup header, or established custom
      within Usenet, so allows (such policies and customs are not
      defined by this standard). Such cancel messages MUST include an
      Approved header identifying the responsible entity. Serving agents
      MAY honour such requests, but SHOULD first take steps to verify
      their appropriateness.
[I think that accords with the accepted norms for 1st, 2nd and 3rd party
cancels (or is a moderator a 1st party?). Observe the use of an Approved
header in place of the present X-Cancelled-By (I cannot see that we need
                          News Article Format                 April 2001
a new header for that when Approved is available). The definitions given
are sufficient to establish which category a cancel was in, assuming
that nobody told any lies, and to establish who had committed abuse
otherwise. So far so good, but we now need authentication methods on top
of all that.]

[A future draft of this standard may contain provisions for a Cancel-
Lock header to enable verification of the authenticity of 1st (and even
2nd) party cancels, and means for digital signatures to establish the
authenticity of 3rd party cancels.]

[A future draft of this standard may also contain provision for a "block
cancel" message, with a list of messages to be canceled contained in its
body rather than in the headers. Whether this needs to have a Control
header at all, and whether the existing "nocem-on-spool" is adequate for
this purpose, and indeed whether NOCEM as such should be part of this,
or some other, standard are issues that are yet to be addressed.]

      cancel-verb         = "cancel"
      cancel-arguments    = CFWS message-id

   The argument identifies the article to be cancelled by its message
   identifier.  The body SHOULD contain an indication of why the
   cancellation was requested. The cancel message SHOULD be posted to
   the same newsgroup(s), with the same distribution(s), as the article
   it is attempting to cancel.

                          News Article Format                  July 2001

   A serving agent that elects to honour a cancel message SHOULD delete
   the target article completely and immediately (or at the minimum make
   the article unavailable for relaying or serving) and also SHOULD
   reject any copies of this article that appear subsequently. See also
   sections 8.3 and 8.4.

        NOTE: The former requirement [RFC 1036] that the From and/or
        Sender headers of the cancel message should match those of the
        original article has been removed from this standard, since it
        only encouraged cancel issuers to conceal their true identity,
        and it was not usually checked or enforced by canceling
        software.  Therefore, both the From and/or Sender headers and
        any Approved header should now relate to the entity responsible
        for issuing the cancel message.

7.6.  Ihave, sendme

   The "ihave" and "sendme" control messages implement a crude batched
   predecessor of the NNTP [NNTP] protocol. They are largely obsolete on
   the Internet, but still see use in conjunction with some transort
   protocols such as UUCP, especially for backup feeds that normally are
   active only when a primary feed path has failed. There is no
   requirement for relaying agents that do not support such transport
   protocols to implement them.

                          News Article Format                 April 2001

        NOTE: The ihave and sendme messages defined here have ABSOLUTELY
        NOTHING TO DO WITH NNTP, despite similarities of terminology.

   The two messages share the same syntax:

      ihave-arguments     = *( msg-id SP ) relayer-name
      sendme-arguments    = ihave-arguments
      relayer-name        = path-identity  ; see 5.6.1
      ihave-body          = *( msg-id CRLF )
      sendme-body         = ihave-body

   Msg-ids MUST appear in either the arguments or the body, but NOT
   both. Relayers SHOULD generate the form putting msg-ids in the body,
   but the other form MUST be supported for backward compatibility.

   The ihave message states that the named relaying agent has received
   articles with the specified message identifiers, which may be of
   interest to the relaying agents receiving the ihave message.  The
   sendme message requests that the agent receiving it send the articles
   having the specified message identifiers to the named relaying agent.

   These control messages are normally sent essentially as point-to-
   point messages, by using newgroups-names newsgroup-names in the Newsgroups header of
   the form "to." followed by one of more components in the form of a
   relayer-name (see section 5.5.1 which forbids "to" as the first
   component of a newgroup-name). newsgroup-name). The control message SHOULD then be
   delivered ONLY to the relaying agent(s) identitifed by that relayer-
   name, and any relaying agent receiving such a message which includes
   its own relayer-name MUST NOT propagate it further. Each pair of
                          News Article Format                  July 2001

   relaying agent(s) sending and receiving these messages MUST be
   immediate neighbors, exchanging news directly with each other. Each
   relaying agent advertises its new arrivals to the other using ihave
   messages, and each uses sendme messages to request the articles it

   To reduce overhead, ihave and sendme messages SHOULD be sent
   relatively infrequently and SHOULD contain reasonable numbers of
   message IDs. If ihave and sendme are being used to implement a backup
   feed, it may be desirable to insert a delay between reception of an
   ihave and generation of a sendme, so that a slightly slow primary
   feed will not cause large numbers of articles to be requested
   unnecessarily via sendme.

7.7.  Obsolete control messages.

   The following control message verbs are declared obsolete by this

                          News Article Format                 April 2001

8.  Duties of Various Agents

   The following section sets out the duties of various agents involved
   in the creation, relaying and serving of Usenet articles.

   In this section, the word "trusted", as applied to the source of some
   article, means that an agent processing that article has verified, by
   some means, the identity of that source (which may be another agent
   or a poster).

        NOTE: In many implementations, a single agent may perform
        various combinations of the injecting, relaying and serving
        functions. Its duties are then the union of the various duties

8.1.  General principles to be followed

   There are two important principles that news implementors (and
   administrators) need to keep in mind. The first is the well-known
   Internet Robustness Principle:

        Be liberal in what you accept, and conservative in what you

   However, in the case of news there is an even more important
   principle, derived from a much older code of practice, the
   Hippocratic Oath (we will thus call this the Hippocratic Principle):

                          News Article Format                  July 2001

        First, do no harm.

   It is VITAL to realize that decisions which might be merely
   suboptimal in a smaller context can become devastating mistakes when
   amplified by the actions of thousands of hosts within a few minutes.

   In the case of gateways, the primary corollary to this is:

        Cause no loops.

8.2.  Duties of an Injecting Agent

   An Injecting Agent is responsible for taking a proto-article from a
   posting agent and either forwarding it to a moderator or injecting it
   into the relaying system for access by readers.

   As such, an injecting agent is considered responsible for ensuring
   that any article it injects conforms with the rules of this standard
   and the policies of any newsgroups or hierarchies that the article is
   posted to. It is also expected to bear some responsibility towards
   the rest of the network for the behaviour of its posters (and
   provision is therefore made for it to be easily contactable by

                          News Article Format                 April 2001

   To this end injecting agents MAY cancel articles which they have
   previously injected (see 7.5).

8.2.1.  Proto-articles

   A proto-article is one that has been created by a posting agent and
   has not yet been injected into the news system by an injecting agent.
   It SHOULD NOT be propagated in that form to other than injecting
   agents. A proto-article has the same format as a normal article
   except that some of the following mandatory headers MAY be omitted:
   Message-Id, Date and Path. These headers MUST NOT contain invalid
   values; they MUST either be correct or not present at all.

   A proto-article SHOULD NOT contain the '%' delimiter in any Path
   header, except in the rare cases where an article gets injected
   twice. It MAY contain path-identities with other delimiters in the
   pre-injection portion of the Path header (5.6.3).

8.2.2.  Procedure to be followed by Injecting Agents

   A injecting agent receives proto-articles from posting and followup
   agents. It verifies them, adds headers where required and then either
   forwards them to a moderator or injects them by passing them to
   serving or relaying agents.

   If an injecting agent receives an otherwise valid article that has
   already been injected it SHOULD either act as if it is a relaying
   agent or else pass the article on to a relaying agent completely
   unaltered. Exceptionally, it MAY reinject the article, perhaps as a
   part of some complex gatewaying process (in which case it will add a
                          News Article Format                  July 2001

   second '%' delimiter to the Path header).  It MUST NOT forward an
   already injected article to a moderator.

   An injecting agent processes articles as follows:

   1. It MUST remove any Injector-Info or Complaints-To header already
      present (though it might be useful to copy them to suitable X-
      headers). It SHOULD likewise remove any NNTP-Posting-Host or other
      undocumented tracing header.

   2. It SHOULD verify that the article is from a trusted source.
      However, it MAY allow articles in which headers contain "forged"
      email addresses, that is, addresses which are not valid for the
      known and trusted source, especially if they end in ".invalid".

   3. It MUST reject any article whose Date header is more than 24 hours
      into the past or into the future (cf. 5.1).

   4. It MUST reject any article that does not have the correct
      mandatory headers for a proto-article (5 and 8.2.1) present, or
      which contains any header that does not have legal contents.

                          News Article Format                 April 2001

   5. If the article is rejected, or is otherwise incorrectly formatted
      or unacceptable due to site policy, the posting agent MUST be
      informed (such as via an NNTP 44x response code) that posting has
      failed and the article MUST NOT then be processed further.

   6. The Message-ID and Date headers (and their content) MUST be added
      when not already present.

   7. A Path header with a tail-entry (5.6.3) MUST be correctly added if
      not already present (except that it SHOULD NOT be added if the
      article is to be forwarded to a moderator).

   8. The path-identity of the injecting agent with a '%' delimiter
      (5.6.2) MUST be prepended to the Path header; moreover, that
      path-identity MUST be an FQDN mailable address (5.6.2).

   9  An Injector-Info header (6.19) SHOULD be added, identifying the
      trusted source of the article, and a suitable Complaints-To header
      (6.20) MAY be added (except that these two headers SHOULD NOT be
      added if the article is to be forwarded to a moderator).

   10.The injecting agent MAY add other headers not already provided by
      the poster, but SHOULD NOT alter, delete or reorder any headers
      already present in the article (except for headers intended for
      tracing purposes, such as Injector-Info and Complaints-To, as
      already mentioned). The injecting agent MUST NOT alter the body of
      the article in any way.

   11.If the Newsgroups line contains one or more moderated groups and
      the article does NOT contain an Approved header, then the
      injecting agent MUST forward it to the moderator of the first
      (leftmost) moderated group listed in the Newsgroups line via
                          News Article Format                  July 2001

      email. The complete article SHOULD be encapsulated (headers and
      all) within the email, preferably using the Content-Type
      "application/news-transmission" (

        NOTE: This standard does not prescribe how the email address of
        the moderator is to be determined, that being a matter of policy
        to be arranged by the agency responsible for the oversight of
        each hierarchy. Nevertheless, there do exist various agents
        worldwide which provide the service of forwarding to moderators,
        and the address to use with them is obtained by replacing each
        '.' in the newsgroups-name with a '-'. For example, articles
        intended for "news.announce.important" would be emailed to
[There is an issue with regard to newsgroup-names using UTF-8.]

   12.Otherwise, the injecting agent forwards the article to one or more
      relaying or serving agents.

8.3.  Duties of a Relaying Agent

   A Relaying Agent accepts injected articles from injecting and other
   relaying agents and passes them on to relaying or serving agents
   according to mutually agreed policy. Relaying agents SHOULD accept
   articles ONLY from trusted agents.

   A relaying agent processes articles as follows:

   1. It MUST verify the leftmost entry in the Path header and then
      prepend its own path-identity with a '/' delimiter, and possibly
      also the verified path-identity of its source with a '?' delimiter

                          News Article Format                 April 2001

   2. It MUST reject any article whose Date header is stale (see 5.1).

   3. It MUST reject any article that does not have the correct
      mandatory headers (section 5) present with legal contents.

   4. It SHOULD reject any article whose optional headers (section 6) do
      not have legal contents.

   5. It SHOULD reject any article that has already been sent to it (a
      database of message identifiers of recent messages is usually kept
      and matched against).

   6. It SHOULD reject any article that has already been Canceled,
      Superseded or Replaced by its author poster or by another trusted entity.

   7. It MAY reject any article without an Approved header posted to
      newsgroups known to be moderated (this practice is strongly
      recommended, but the information necessary to do it may not be
      available to all agents).

                          News Article Format                  July 2001

   8. It then passes articles which match mutually agreed criteria on to
      neighboring relaying and serving agents. However, it SHOULD NOT
      forward articles to sites whose path-identity is already in the
      Path header.

        NOTE: It is usual for relaying and serving agents to restrict
        the Newsgroups, Distributions, age and size of articles that
        they wish to receive.

   If the article is rejected as being invalid, unwanted or unacceptable
   due to site policy, the agent that passed the article to the relaying
   agent SHOULD be informed (such as via an NNTP 43x response code) that
   relaying failed. In order to prevent a large number of error messages
   being sent to one location, relaying agents MUST NOT inform any other
   external entity that an article was not relayed UNLESS that external
   entity has explicitly requested that it be informed of such errors.

        NOTE: In order to prevent overloading, relaying agents should
        not routinely query an external entity (such as a DNS-server) in
        order to verify an article (though a local cache of the required
        information might usefully be consulted).

   Relaying agents MUST NOT alter, delete or rearrange any part of an
   article expect for the Path and Xref Headers. headers designated as variant (

8.4.  Duties of a Serving Agent

   A Serving Agent takes an article from a relaying or injecting agent
   and files it in a "news database". It also provides an interface for
   reading agents to access the news database. This database is normally
   indexed by newsgroup with articles in each newsgroup identified by an
   article-locater (usually in the form of a decimal number - see 6.16).

                          News Article Format                 April 2001

        NOTE: Since control messages are often of interest, but should
        not be displayed as normal articles in regular newsgroups, it is
        common for serving agents to make them available in a pseudo-
        newsgroup named "control" or in a pseudo-newsgroup in a sub-
        hierarchy under "control." (e.g. "control.cancel").

   A serving agent processes articles as follows:

   1. It MUST verify the leftmost entry in the Path header and then
      prepend its own path-identity with a '/' delimiter, and possibly
      also the verified path-identity of its source with a '?' delimiter

   2. It MUST reject any article whose Date header is stale (see 5.1).

   3. It MUST reject any article that does not have the correct
      mandatory headers (section 5) present, or which contains any
      header that does not have legal contents.

                          News Article Format                  July 2001

   4. It SHOULD reject any article that has already been sent to it (a
      database of message identifiers of recent messages is usually kept
      and matched against).

   5. It SHOULD reject any article that has already been Canceled,
      Superseded or Replaced by its author poster or by another trusted entity,
      and delete any of such article that it already has in its news

   6. It MUST reject any article without an Approved header posted to
      any moderated newsgroup which it is configured to receive, and it
      MAY reject such articles for any newsgroup it knows be moderated.

   7. It SHOULD remove any variant headers ( from each article
      and MUST, in particular, remove any Xref header (6.16).  It then
      MAY (and usually will) generate a correct fresh Xref header (6.16) for each article. header.

   8. Finally, it stores the article in its news database.

8.5.  Duties of a Posting Agent

   A Posting Agent is used to assist the poster in creating a valid
   proto-article and forwarding it to an injecting agent.

   Postings agents SHOULD ensure that proto-articles they create are
   valid Netnews articles according to this standard and other
   applicable policies.

   Posting agents meant for use by ordinary posters SHOULD reject any
   attempt to post an article which cancels, Supersedes or Replaces
   another article of which the poster is not the author.

8.6.  Duties of a Followup Agent

   A Followup Agent is a special case of a posting agent and as such is
   bound by all the posting agent's requirements plus additional ones.
   Followup agents MUST create valid followups, in particular by
                          News Article Format                 April 2001
   providing correctly adjusted forms of those headers described as
   inheritable (, notably the Newgroups Newsgroups header (5.5), the
   Subject header (5.4) and the References header (6.10), and they Ought
   to observe appropriate quoting conventions in the body (see 4.3.2).

   Followup agents SHOULD initialize the Newsgroups header from the
   precursor's Followup-To header, if present, when preparing a
   followup; however posters MAY then change this before posting if they

   Followup agents MUST NOT attempt to send email to any address ending
   in ".invalid".  Followup agents SHOULD NOT email copies of the
   followup to the author poster of the precursor unless this has been
   explicitly requested by means of a Mail-Copies-To header (6.8), but
   they SHOULD include a Posted-And-Mailed header (6.9) whenever a copy
   is so emailed.

                          News Article Format                  July 2001

8.7.  Duties of a Moderator

   A Moderator receives news articles by email, decides whether to
   accept them and, if so, either injects them into the news stream or
   forwards them to further moderators.

   A moderator processes an article, as submitted to any newsgroup that
   he moderates, as follows:

   1. He decides, on the basis of whatever moderation policy applies to
      his group, whether to accept or reject the article. He MAY do this
      manually, or else partially or wholly with the aid of appropriate
      software for whose operation he is then responsible. He MAY modify
      the article if that is in accordance with the applicable
      moderation policy (and in particular he MAY remove redundant
      headers and add Comments and other informational headers). He MAY
      inform the poster as to whether the article has been accepted or

      If the article is rejected, then it fails for all the newsgroups
      for which it was intended (in particular the moderator SHOULD NOT
      resubmit the article, with a reduced Newsgroups header, to any
      remaining groups, especially if this will break any authentication
      checks present in the article). If the article is accepted, the
      moderator proceeds with the following steps.

   2. The Date header SHOULD be retained, except that if it is stale
      (5.1) for reasons understood by the moderator (e.g. delays in the
      moderation process) he MAY substitute the current date (but must
      then take responsibility for any loops that ensue). Any local
      headers ( or variant
      headers ( ( MUST be removed, except that a Path header MAY
      be truncated to only its pre-
      injection pre-injection region (5.6.3).  Any
      Injector-Info header (6.19) or Complaints-To header (6.20) MUST be
[Note several differences from Kent Landfield's 'Moderator's Handbook'.
The original Date and Message-ID are retained.
Any Distribution header is retained.

                          News Article Format                 April 2001
Any Sender header is retained.
Various other minor headers are retained (though the moderator MAY, of
course, remove them.

   3. He adds an Approved header (6.14) containing a mailbox identifying
      himself (or, if the article already contains an Approved header
      from another moderator, he adds that identifying information to
      it). He MAY also add further headers to authenticate that the
      article has been properly approved.
[That can be strengthened when we have defined proper authentication

   4. If the Newsgroups header contains further moderated newsgroups for
      which approval has not already been given, he forwards the article
      to the moderator of the leftmost such group (which, if this
      standard has been followed correctly, will always be the group
                          News Article Format                  July 2001

      immediately to the right of the group(s) for which he is
      responsible). However, he MUST NOT alter the order in which the
      newsgroups are listed in the Newsgroups header.

   5. Otherwise, he causes the article to be injected, having first
      observed all the duties of a posting agent (8.5).

        NOTE: This standard does not prescribe how the moderator or
        moderation policy for each newsgroup is established; rather it
        assumes that whatever agencies are responsible for the relevant
        network or hierarchy (1.1) will have made appropriate
        arrangements in that regard.

   It SHOULD be the case that articles will be received by the moderator
   encapsulated as an object of Content-Type application/news-
   transmission (8.2.2), or possibly encapsulated but without an
   explicit Content-Type header. In such a case, the complete article is
   immediately available for processing by the moderator.

   However, prior to the introduction of this standard, it was more
   common for injecting agents to transform proto-articles into mail
   messages, mixing the Netnews headers with the Mail headers.
   Moderators SHOULD therefore be prepared to accept submission in this
   format, although they need then to be aware of the Duties of an
   Incoming Gateway (8.8.2) (and, in particular, they SHOULD adopt the
   Message-ID and Date headers of the mail message, though they SHOULD
   NOT add any Sender header).

8.8.  Duties of a Gateway

   A Gateway transforms an article into the native message format of
   another medium, or translates the messages of another medium into
   news articles. Encapsulation of a news article into a message of MIME
   type application/news-transmission, or the subsequent undoing of that
   encapsulation, is not gatewaying, since it involves no transformation
   of the article.

                          News Article Format                 April 2001

   There are two basic types of gateway, the Outgoing Gateway that
   transforms a news article into a different type of message, and the
   Incoming Gateway that transforms a message from another medium into a
   news article and injects it into a Netnews system. These are handled
   separately below.

   The primary dictat for a gateway is:

        Above all, prevent loops.

   Transformation of an article into another medium stands a very high
   chance of discarding or interfering with the protection inherent in
   the news system against duplicate articles. The most common problem
   caused by gateways is "spews," gateway loops that cause previously
   posted articles to be reinjected repeatedly into Usenet. To prevent
   this, a gateway MUST take precautions against loops, as detailed

                          News Article Format                  July 2001

   If bidirectional gatewaying (both an incoming and an outgoing
   gateway) is being set up between Netnews and some other medium, the
   incoming and outgoing gateways SHOULD be coordinated to avoid
   reinjection of gated articles. Circular gatewaying (gatewaying a
   message into another medium and then back into Netnews) SHOULD NOT be
   done; encapsulation of the article SHOULD be used instead where this
   is necessary.

   A second general principal of gatewaying is that the transformations
   applied to the message SHOULD be as minimal as possible while still
   accomplishing the gatewaying. Every change made by a gateway
   potentially breaks a property of one of the media or loses
   information, and therefore only those transformations made necessary
   by the differences between the media should be applied.

   It is worth noting that safe bidirectional gatewaying between a
   mailing list and a newsgroup is far easier if the newsgroup is
   moderated. Posts to the moderated group and submissions to the
   mailing list can then go through a single point that does the
   necessary gatewaying and then sends the message out to both the
   newsgroup and the mailing list at the same time, eliminating most of
   the possibility of loops. Bidirectional gatewaying between a mailing
   list and an unmoderated newsgroup, in contrast, is difficult to do
   correctly and is far more fragile.

   Newsgroups intended to be bidirectionally gated to a mailing list
   SHOULD therefore be moderated where possible, even if the moderator
   is a simple gateway and injecting agent that correctly handles
   crossposting to other moderated groups and otherwise passes all

8.8.1.  Duties of an Outgoing Gateway

   From the perspective of Netnews, an outgoing gateway is just a
   special type of reading agent. The exact nature of what the outgoing
   gateway will need to do to articles depends on the medium to which
                          News Article Format                 April 2001
   the articles are being gated. The operation of the outgoing gateway
   is only subject to additional constraints in the presence of one or
   more corresponding incoming gateways back from that medium to
   Netnews, since this opens the possibility of loops.

   It is recommended, however, that the following practices be followed
   by all outgoing gateways regardless of whether there is known to be a
   related incoming gateway, both as a precautionary measure and as a
   guideline to quality of implementation.

   1. Only the minimal necessary changes should be made, as stated

   2. The message identifier of the news article should be preserved if
      at all possible, preferably as or within the corresponding unique
      identifier of the other medium, but if not at least as a comment
      in the message. This helps greatly with preventing loops.

                          News Article Format                  July 2001

   3. The Date of the news article should also be preserved if possible,
      for similar reasons.

   4. The message should be tagged in some way so as to prevent its
      reinjection into Netnews. This may be impossible to do without
      knowledge of potential incoming gateways, but it is better to try
      to provide some indication even if not successful; at the least, a
      human-readable indication that the article should not be gated
      back to Netnews can help locate a human problem.

   5. News control messages should not be gated to another medium unless
      they would somehow be meaningful in that medium.

8.8.2.  Duties of an Incoming Gateway

   The incoming gateway has the serious responsibility of ensuring that
   all of the requirements of this standard are met by the articles that
   it forms. In addition to its special duties as a gateway, it bears
   all of the duties and responsibilities of an injecting agent as well,
   and additionally has the same responsibility of a relaying agent to
   reject articles that it has already gatewayed.

   An incoming gateway MUST NOT gate the same message twice. It may not
   be possible to ensure this in the face of mangling or modification of
   the message, but at the very least a gateway, when given a copy of a
   message it has already gated identical except for trace headers (like
   Received in e-mail or Path in Netnews) MUST NOT gate the message
   again.  An incoming gateway SHOULD take precautions against having
   this rule bypassed by modifications of the message that can be

   News articles prepared by gateways MUST be legal news articles. In
   particular, they MUST include all of the mandatory headers and MUST
   fully conform to the restrictions on said headers. This often
   requires that a gateway function not only as a relaying agent, but
   also partly as a posting agent, aiding in the synthesis of a
                          News Article Format                 April 2001
   conforming article from non-conforming input.

   Incoming gateways MUST NOT pass control messages (articles containing
   a Control header) without removing or renaming that header. Gateways
   MAY, however, generate their own cancel messages, under the general
   allowance for injecting agents to cancel their own messages (7.5).
   If a gateway receives a message that it can determine is a valid
   equivalent of a cancel message in the medium it is gatewaying, it
   SHOULD discard that message without gatewaying it, generate a
   corresponding cancel message of its own, and inject that cancel

   Incoming gateways MUST NOT inject control messages other than
   cancels.  Encapsulation SHOULD be used instead of gatewaying, when
   direct posting is not possible or desirable.

                          News Article Format                  July 2001

        NOTE: It is not unheard of for mail-to-news gateways to be used
        to post control messages, but encapsulation should be used for
        these cases instead. Gateways by their very nature are
        particularly prone to loops. Spews of normal articles are bad
        enough; spews of control messages with special significance to
        the news system, possibly resulting in high processing load or
        even e-mail sent for every message received, are catastrophic.
        It is far preferable to construct a system specifically for
        posting control messages that can do appropriate consistency
        checks and authentication of the originator of the message.

   If there is a message identifier that fills a role similar to that of
   the Message-ID header in news, it SHOULD be used in the formation of
   the message identifier of the news article, perhaps with
   transformations required to meet the uniqueness requirement of
   Netnews. This transformation SHOULD be designed so that two messages
   with the same identifier generate the same Message-ID header.

        NOTE: Message identifiers play a central role in the prevention
        of duplicates, and their correct use by gateways will do much to
        prevent loops. Netnews does, however, require that message
        identifiers be unique, and therefore message identifiers from
        other media may not be suitable for use without modification. A
        balance must be struck by the gateway between preserving
        information used to prevent loops and generating unique message

   Exceptionally, if there are multiple incoming gateways for a
   particular set of messages, each to a different newsgroup(s), each
   one SHOULD generate a message identifier unique to that gateway. Each
   incoming gateway nonetheless MUST ensure that it does not gate the
   same message twice.

        NOTE: Consider the example of two gateways of a given mailing
        list into the world-wide Usenet newsgroups, both of which
        preserve the mail message identifier. Each newsgroup may then
        receive a portion of the messages (different sites seeing
        different portions).  In these cases, where there is no one
                          News Article Format                 April 2001
        "official" gateway, some other method of generating message
        identifiers has to be used to avoid collisions. It would
        obviously be preferable for there to be only one gateway which
        crossposts, but this may not be possible to coordinate.

   If no date information is available, the gateway MAY supply a Date
   header with the gateway's current date. If only partial information
   is available (e.g. date but not time), this SHOULD be fleshed out to
   a full Date header by adding default values rather than discarding
   this information. Only in very exceptional circumstances should Date
   information be discarded, as it plays an important role in preventing
   reinjection of old messages.

   An incoming gateway MUST add a Sender header to the news article it
   forms containing the mailbox of the administrator of the gateway.
   Problems with the gateway may be reported to this address. The
                          News Article Format                  July 2001

   display-name portion of this mailbox SHOULD indicate that the entity
   responsible for injection of the message is a gateway. If the
   original message already had a Sender header, it SHOULD be renamed so
   that its contents can be preserved.

8.8.3.  Example

   To illustrate the type of precautions that should be taken against
   loops, here is an example of the measures taken by one particular
   combination of mail-to-news and news-to-mail gateways at Stanford
   University designed to handle bidirectional gatewaying between
   mailing lists and unmoderated groups.

   1. The news-to-mail gateway preserves the message identifier of the
      news article in the generated mail message. The mail-to-news
      gateway likewise preserves the mail message identifier provided
      that it is syntactically valid for Netnews.  This allows the news
      system's built-in suppression of duplicates to serve as the first
      line of defense against loops.

   2. The news-to-mail gateway adds an X-Gateway header to all messages
      it generates. The mail-to-news gateway discards any incoming
      messages containing this header. This is robust against mailing
      list managers that replace the message identifier, and against any
      number of mail hops, provided that the other message headers are

   3. The mail-to-news gateway inserts the host name from which it
      received the mail message in the pre-injection region of the Path
      (5.6.3).  The news-to-mail gateway refuses to gateway any message
      that contains the list server name in the pre-injection region of
      its Path header. This is robust against any amount of munging of
      the message headers by the mailing list, provided that the mail
      only goes through one hop.

   4. The mail-to-news gateway is designed never to generate bounces to
      the envelope sender. Instead, articles that are rejected by the
      news server (for reasons not warranting silent discarding of the
                          News Article Format                 April 2001
      message) result in a bounce message sent to an errors address
      known not to forward to any mailing lists, so that they can be
      handled by the news administrators.

   These precautions have proven effective in practice at preventing
   loops for this particular application (bidirectional gatewaying
   between mailing lists and locally distributed newsgroups where both
   gateways can be designed together). General gatewaying to world-wide
   newsgroups poses additional difficulties; one must be very wary of
   strange configurations, such as a newsgroup gated to a mailing list
   which is in turn gated to a different newsgroup.

                          News Article Format                  July 2001

9.  Security and Related Considerations

   There is no security. Don't fool yourself. Usenet is a prime example
   of an Internet Adhocratic-Anarchy; that is, an environment in which
   trust forms the basis of all agreements.  It works.

9.1.  Leakage

   Articles which are intended to have restricted distribution are
   dependent on the goodwill of every site receiving them.  The
   "Archive: no" header (6.12) is available as a signal to automated
   archivers not to file an article, but that cannot be guaranteed.

   The Distribution header makes provision for articles which should not
   be propagated beyond a cooperating subnet. The key security word here
   is "cooperating". When a machine is not configured properly, it may
   become uncooperative and tend to distribute all articles.

   The flooding algorithm is extremely good at finding any path by which
   articles can leave a subnet with supposedly restrictive boundaries,
   and substantial administrative effort is required to avoid this.
   Organizations wishing to control such leakage are strongly advised to
   designate a small number of official gateways to handle all news
   exchange with the outside world (however, making such gateways too
   restrictive can also encourage the setting up of unofficial paths
   which can be exceedingly hard to track down).

   The sendme control message (7.6), insofar as it is still used, can be
   used to request articles with a given message identifier, even one
   that is not supposed to be supplied to the requestor.

9.2.  Attacks

9.2.1.  Denial of Service

   The proper functioning of individual newsgroups can be disrupted by
   the massive posting of "noise" articles, by the repeated posting of
   identical or near identical articles, by posting followups unrelated
   to their precursors, or which quote their precursors in full with the
   addition of minimal extra meterial material (especially if this process is
   iterated), and by crossposting to, or setting followups to, totally
   unrelated newsgroups.

                          News Article Format                 April 2001

   Many have argued that "spam", massively multiposted (and to a lesser
   extent massively crossposted) articles, usually for advertising
   purposes, also constitutes a DoS attack in its own regard.  This may
   be so.

   Such articles intended to deny service, or other articles of an
   inflammatory nature, may also have their From or Reply-To addresses
   set to valid but incorrect email addresses, thus causing large
   volumes of mail to descend on the true owners of those addresses.

                          News Article Format                  July 2001

   It is a violation of this standard for a poster to use as his address
   a mailbox which he is not entitled to use.  Even addresses with an
   invalid local-part but a valid domain can cause disruption to the
   administrators of such domains.  Posters who wish to remain anonymous
   or to prevent automated harvesting of their addresses, but who do not
   care to take the additional precautions of using more sophisticated
   anonymity measures, should avoid that violation by the use of
   addresses ending in the ".invalid" top-level-domain (see 5.2).

   A malicious poster may also prevent his article being seen at a
   particular site by preloading that site into the Path header (5.6.1)
   and may thus prevent the true owner of a forged From or Reply-To
   addresse from ever seeing it.

   Administrative agencies with responsibility for establishing policies
   in particular hierarchies can and should set bounds upon the
   behaviour that is considered acceptable within those hierarchies (for
   example by promulgating charters for individual newsgroups, and other
   codes of conduct).

   Whilst this standard places an onus upon injecting agents to bear
   responsibility for the misdemeanours of its their posters, (which include
   includes non-adherence to established policies of the relevant
   hierarchies as provided in section 8.2), and to provide assistance to
   the rest of the network by making proper use of the Injector-Info
   (6.19) and Complaints-To (6.20) headers, it makes no provision for
   enforcement, which may in consequence be patchy. Nevertheless,
   injecting sites which persistently fail to honour their
   respobsibilities or to comply with generally accpted standards of
   behaviour are likely to find themselves blacklisted, with their
   articles refused progagation and even subject to cancellation, and
   other relaying sites would be well advised to withdraw peering
   arrangements from them.

9.2.2.  Compromise of System Integrity

   The posting of unauthorized (as determined by the policies of the
   relevant hierarchy) control messages can cause unwanted newsgroups to
   be created, or wanted ones removed, from serving agents.
   Administrators of such agents SHOULD therefore take steps to verify
   the genuiness of such control messages, either by manual inspection
   (particularly of the Approved header) or by checking any digital
   signatures that may be provided. In addition, they SHOULD
   periodically compare the newsgroups carried against any regularly
   issued checkgroups messages, or against lists maintained by trusted
                          News Article Format                 April 2001
   servers and accessed by out-of-band protocols such as FTP or HTTP.

   Malicious cancel messages (7.5) can cause valid articles to be
   removed from serving agents. Administrators of such agents SHOULD
   therefore take steps to verify that they originated from the poster,
   the injector or the moderator of the article, or that in other cases
   they came from a place that is trusted to work within established
   policies and customs. Articles containing Replaces and/or Supersedes
   headers (6.15) are effectively cancel messages, and SHOULD be subject
                          News Article Format                  July 2001

   to the same checks.  Currently, many sites choose to ignore all
   cancel messages on account of the difficulty of conducting such
[But we cannot really say much more until we have Cancel Locks and
digital signatures in place.]

   Improperly configured serving agents can allow articles posted to
   moderated groups onto the net without first being approved by the
   moderator. Injecting agents SHOULD verify that moderated articles
   were was received from one of the entities given in its their Approved
   headers and/or check any digital signatures that may be provided.

   The filename parameter of the Archive header (6.12) can be used to
   attempt to store archived articles in inappropriate locations.
   Archiving sites should be suspicious of absolute filename parameters,
   as opposed to those relative to some location of the archiver's

   There may be weaknesses in particular implementations that are
   subject to malicious exploitation. In particular, it has not been
   unknown for complete shell scripts to be included within Control
   headers. Implementors need to be aware of this.

   Reading agents should be chary of acting automatically upon Mime
   objects with an "application" Content-Type that could change the
   state of that agent, except in contexts where such applications are
   specifically expected (see 6.21).  Even the Content-Type "text/html"
   could have unexpected side effects on account of embedded objects,
   especially embedded executable code or URLs that invoke non-news
   protocols such as HTTP [RFC 2616].  It is therefore generally
   recommended that reading agents do not enable the execution of such
   code (since it is extremely unlikely to have a valid application
   within Netnews) and that they only honour URLs referring to other
   parts of the same article.

   Non-printable characters embedded in article bodies may have
   surprising effects on printers or terminals, notably by reconfiguring
   them in undesirable ways which may become apparent only after the
   reading agent has terminated.

9.3.  Liability

   There is a presumption that a poster who sends an article to Usenet
   intends it to be stored on a multitude of serving agents, and has
   therefore given permission for it to be copied to that extent.
   Nevertheless, Usenet is not exempt from the Copyright laws, and it
   should not be assumed that permission has been given for the article
   to be copied outside of Usenet, not nor for its permanent archiving
   contrary to any Archive header that may be present.

                          News Article Format                 April 2001

   Posters also need to be aware that they are responsible if they
   breach Copyright, Libel, Harrassment or other restrictions relating
   to material that they post, and that they may possibly find
   themselves liable for such breaches in jurisdictions far from their
                          News Article Format                  July 2001

   own. Serving agents may also be liable in some jurisdictions,
   especially if the breach has been explicitly drawn to their

   Users who are concerned about such matters should seek advice from
   competent legal authorities.

10.  References

   [ANSI X3.4] "American National Standard for Information Systems -
        Coded Character Sets - 7-Bit American National Standard Code for
        Information Interchange (7-Bit ASCII)", ANSI X3.4, 1986.

   [ISO 10646] "International Standard - Information technology -
        Universal Multiple-Octet Coded Character Set (UCS) - Part 1:
        Architecture and Basic Multilingual Plane", ISO/IEC 10646-1,

   [ISO 3166] "Codes for the representation of names of countries and
        their subdivisions -- Part 1: Country codes", ISO 3166, 1997.

   [ISO 8859] International Standard - Information Processing - 8-bit
        Single-Byte Coded Graphic Character Sets.  Part 1: Latin
        alphabet No. 1, ISO 8859-1, 1987 Part 2: Latin alphabet No. 2,
        ISO 8859-2, 1987 Part 3: Latin alphabet No. 3, ISO 8859-3, 1988
        Part 4: Latin alphabet No. 4, ISO 8859-4, 1988 Part 5:
        Latin/Cyrillic alphabet, ISO 8859-5, 1988 Part 6: Latin/Arabic
        alphabet, ISO 8859-6, 1987 Part 7: Latin/Greek alphabet, ISO
        8859-7, 1987 Part 8: Latin/Hebrew alphabet, ISO 8859-8, 1988

   [MESSFOR] P. Resnick, "Internet Message Format Standard", draft-
        ietf-drums-msg-fmt-07.txt, March 1998.

   [ISO/IEC 10646] "International Standard - Information technology -
        Universal Multiple-Octet Coded Character Set (UCS) - Part 1:
        Architecture and Basic Multilingual Plane", ISO/IEC 10646-
        1:2000, 2000.

   [NNTP] S. Barber, "Network News Transport Protocol", draft-ietf-

   [RFC 1034] P. Mockapetris, "Domain Names - Concepts and Facilities",
        RFC 1034, November 1987.

   [RFC 1036] M. Horton and R. Adams, "Standard for Interchange of
        USENET Messages", RFC 1036, December 1987.

   [RFC 1153] F. Wancho, "Digest Message Format", RFC 1153, April 1990.

   [RFC 1738] T. Berners-Lee, L. Masinter, and M. McCahill, "Uniform
        Resource Locators (URL)", RFC 1738, December 1994.

   [RFC 1847] J. Galvin, S. Murphy, S. Crocker, and N. Freed, "Security
        Multiparts for MIME: Multipart/Signed and Miltipart/Encrypted",
                          News Article Format                 April 2001
        RFC 1847, October 1995.

   [RFC 2015] M. Elkins, "MIME Security with Pretty Good Privacy (PGP)",
        RFC 2015, October 1996.

   [RFC 2044] F. Yergeau, "UTF-8, a transformation format for Unicode 2015bis] M. Elkins, D. Del Torto, R. Levien, and ISO 10646", RFC 2044, October 1996. T. Roessler,
        "MIME Security with OpenPGP", draft-ietf-openpgp-mime-06.txt,
                          News Article Format                  July 2001

        April 2001.

   [RFC 2045] N. Freed and N. Borenstein, "Multipurpose Internet Mail
        Extensions (MIME) Part One: Format of Internet Message Bodies",
        RFC 2045, November 1996.

   [RFC 2046] N. Freed and N. Borenstein, "Multipurpose Internet Mail
        Extensions (MIME) Part Two: Media Types", RFC 2046, November

   [RFC 2047] K. Moore, "MIME (Multipurpose Internet Mail Extensions)
        Part Three: Message Header Extensions for Non-ASCII Text", RFC
        2047, November 1996.

   [RFC 2048] N. Freed, J. Klensin, and J. Postel, "Multipurpose
        Internet Mail Extensions (MIME) Part Four: Registration
        Procedures", RFC 2048, November 1996.

   [RFC 2119] S. Bradner, "Key words for use in RFCs to Indicate
        Requirement Levels", RFC 2119, March 1997.

   [RFC 2142] D. Crocker, "Mailbox Names for Common Services, Roles and
        Functions", RFC 2142, May 1997.

   [RFC 2234] D. Crocker and P. Overell, "Augmented BNF for Syntax
        Specifications: ABNF", RFC 2234, November 1997.

   [RFC 2279] F. Yergeau, "UTF-8, a transformation format of ISO 10646",
        RFC 2279, January 1998.

   [RFC 2373] R. Hinden and S. Deering, "IP Version 6 Addressing
        Architecture", RFC 2373, July 1998.

   [RFC 2440] J. Callas, L. Donnerhacke, H. Finney, and R. Thayer,
        "OpenPGP Message Format", RFC 2440, November 1998.

   [RFC 2606] D. Eastlake and A. Panitz, "Reserved Top Level DNS Names",
        RFC 2606, June 1999.

   [RFC 2616] R. Fielding, J. Gettys, J. Mogul, H. Frystyk, L. Masinter,
        P. Leach, and T. Berners-Lee, "Hypertext Transfer Protocol --
        HTTP/1.1", RFC 2616, June 1999.

   [RFC 2821] John C. Klensin and Dawn P. Mann, "Simple Mail Transfer
        Protocol", RFC 2821, April 2001.

   [RFC 2822] P. Resnick, "Internet Message Format", RFC 2822, April

   [RFC 820] J. Postel and J. Vernon, "Assigned Numbers", RFC 820,
        January 1983.

   [RFC 822] D. Crocker, "Standard for the Format of ARPA Internet Text
        Messages.", STD 11, RFC 822, August 1982.

                          News Article Format                  July 2001

   [RFC 850] Mark R. Horton, "Standard for interchange of Usenet
        messages", RFC 850, June 1983.

                          News Article Format                 April 2001

   [RFC 976] Mark R. Horton, "UUCP mail interchange format standard",
        RFC 976, February 1986.

   [SMTP] John C. Klensin and Dawn P. Mann, "Simple Mail Transfer
        Protocol", draft-ietf-drums-smtpupd-*.txt.

   [Son-of-1036] Henry Spencer, "News article format and transmission",
        <>, June 1994.


   [UNICODE 3.0] The Unicode Consortium, "The Unicode Standard - Version
        3.0", Addison-Wesley, 1996. 2000.

   [UNICODE 3.1] The Unicode Consortium, "The Unicode Standard - Version
        3.1, being an amendment to [UNICODE 3.0]", Unicode Standard
        Annex #27 <>, 2001.

   [USEFOR] Charles H. Lindsey, "News Article Format", draft-ietf-

11.  Acknowledgements

[It is intended to insert a list of those who have been prominent
contributors to the mailing list of the working group at this point.]

12.  Contact Addresses


        Charles. H. Lindsey
        5 Clerewood Avenue
        Heald Green
        Cheshire SK8 3JU
        United Kingdom
        Phone: +44 161 436 6131

Working group chair

        David Barr
        Digital Island

   Comments on this draft should preferably be sent to the mailing list
   of the Usenet Format Working Group at

   This draft expires six months after the date of publication (see Page
   1) (i.e. in October 2001). January 2002).

                          News Article Format                  July 2001

13.  Intellectual Property Rights

[The following are taken from RFC 2026. It is not entirely clear whether
all of this is necessary at this stage. Please can someone explain it to
                          News Article Format                 April 2001

   The IETF takes no position regarding the validity or scope of any
   intellectual property or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; neither does it represent that it
   has made any effort to identify any such rights.  Information on the
   IETF's procedures with respect to rights in standards-track and
   standards-related documentation can be found in BCP-11.  Copies of
   claims of rights made available for publication and any assurances of
   licenses to be made available, or the result of an attempt made to
   obtain a general license or permission for the use of such
   proprietary rights by implementors or users of this specification can
   be obtained from the IETF Secretariat.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights which may cover technology that may be required to practice
   this standard.  Please address the information to the IETF Executive

   Copyright (C) The Internet Society (date). All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implmentation may be prepared, copied, published and
   distributed, in whole or in part, without restriction of any kind,
   provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the  purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an

                          News Article Format                  July 2001

Appendix A.1 - A-News Article Format

   The obsolete "A News" article format consisted of exactly five lines
   of header information, followed by the body. For example:

                          News Article Format                 April 2001

      Fri Nov 19 16:14:55 1982
      Usenet Etiquette - Please Read

   The first line consisted of an "A" followed by an article ID
   (analogous to a message ID and used for similar purposes).  The
   second line was the list of newsgroups. The third line was the path.
   The fourth was the date, in the format above (all fields fixed
   width), resembling an Internet date but not quite the same. The fifth
   was the subject.

   This format is documented for archeological purposes only.  Articles
   MUST NOT be generated in this format.

Appendix A.2 - Early B-News Article Format

   The obsolete pseudo-Internet article format, used briefly during the
   transition between the A News format and the modern format, followed
   the general outline of a MAIL message but with some non-standard
   headers. For example:

      From: cbosgd!mhuxj!mhuxt!eagle!jerry (Jerry Schwarz)
      Newsgroups: news.misc
      Title: Usenet Etiquette -- Please Read
      Article-I.D.: eagle.642
      Posted: Fri Nov 19 16:14:55 1982
      Received: Fri Nov 19 16:59:30 1982
      Expires: Mon Jan 1 00:00:00 1990


   The From header contained the information now found in the Path
   header, plus possibly the full name now typically found in the From
   header. The Title header contained what is now the Subject content.
   The Posted header contained what is now the Date content. The
   Article-I.D. header contained an article ID, analogous to a message
   ID and used for similar purposes. The Newsgroups and Expires headers
   were approximately as now. The Received header contained the date
   when the latest relayer to process the article first saw it. All
   dates were in the above format, with all fields fixed width,
   resembling an Internet date but not quite the same.

                          News Article Format                  July 2001

   This format is documented for archeological purposes only.  Articles
   MUST NOT be generated in this format.

                          News Article Format                 April 2001

Appendix A.3 - Obsolete Headers

   Early versions of news software following the modern format sometimes
   generated headers like the following:

      Relay-Version: version B 2.10 2/13/83; site cbosgd.UUCP
      Posting-Version: version B 2.10 2/13/83; site eagle.UUCP
      Date-Received: Friday, 19-Nov-82 16:59:30 EST

   Relay-Version contained version information about the relayer that
   last processed the article. Posting-Version contained version
   information about the posting agent that posted the article. Date-
   Received contained the date when the last relayer to process the
   article first saw it (in a slightly nonstandard format).

   In addition, this present standard obsoletes certain headers defined
   in [Son-of-1036] (see 6.22): 6.22

      Also-Control: cancel <9urrt98y53@site.example>
      See-Also: <i4g587y@site1.example> <kgb2231+ee@site2.example>
      Article-Updates: <i4g587y@site1.example>

   Also-Control indicated a control message that was also intended to be
   filed as a normal article. See-Also listed related articles, but
   without the specfic relationship with followups that pertains to the
   References header.  Article-Names indicated some special significance
   of that article in relation to the indicated newsgroup. Article-
   Updates indicated that an earlier article was updated, without at the
   same time being superseded.

   These headers are documented for archeological purposes only.
   Articles containing these headers MUST NOT be generated.

Appendix A.4 - Obsolete Control Messages

   This present standard obsoletes certain control messages defined in
   [RFC 1036] (see 7.7), 7.7 all of which had the effect of requesting a
   description of a relaying or serving agent's software, or its peering
   arrangements with neighbouring sites, to be emailed to the article's
   reply address. Whilst of some utility when Usenet was much smaller
   than it is now, they had become no more than a tool for the malicious
   sending of mailbombs. Moreover, many organizations now consider
   information about their internal connectivity to be confidential.

                          News Article Format                  July 2001

   "Version" requested details of the transport software in use at a
   site.  "Sendsys" requested the full list of newsgroups taken, and the
   peering arrangements. "Who gets" was similar, but restricted to a
   named newsgroup.  "Senduuname" resembled "sendsys" but restricted to
                          News Article Format                 April 2001
   the list of peers connected by UUCP.

   Historically, a checkgroups body consisting of one or two lines, the
   first of the form "-n newsgroup", caused check-groups to apply to
   only that single newsgroup.

   Historically, an article posted to a newsgroup whose name had exactly
   three components of which the third was "ctl" signified that article
   was to be taken as a control message.  The Subject header specified
   the actions, in the same way the Control header does now.

   These forms are documented for archeological purposes only; they MUST
   NO LONGER be used.

Appendix B - Collected Syntax